LID SU

PPOR

TS319

1-800-562-5267(U.S.A. Only)

www.sugatsune.com

Face Frame Bracket: FFCB-SD-1(Sold separately, see P.345)

Mounting Plate SDS-A(Included)

White Black

SDS-C100/BLK

SDH-001/NI(Sold separately)

Hinge Type A A´ B B´ C C´Single Knuckle Hinge 100 (3-15/16") - 135 (5-5/16") - 218 (8-37/64") -

Drop Hinge* - 107 (4-7/32") - 142 (5-19/32") - 225 (8-55/64")

Material Finish/ColorSteel, Zinc Alloy Nickel

Plastic Black, White

Item No. Color Weight (g) Box (pcs) Carton (pcs) SDS-C100/WHT White

167 20 100 SDS-C100/BLK Black

• For DOWNWARD-OPENING FLAP DOOR used with piano, butt or drop hinges (SDH-001, SDH-P, P.238).

• SDS-C100 (with catch) is designed to hold door in closed position.

• SDS-100 does not have a catch feature. Designed to be used with a magnetic catch or touch latch.

• Non-handed.• Torque Calculation:

Torque = Door Height × 1/2 × Door Weight Per Piece: 35~50 kg·cm (30~43 lbs·inch) Per Pair: 70~100 kg·cm (60~86 lbs·inch)

• Recommended Door Thickness: 20 mm (25/32")• Short-arm version SDS-100TV (or C100TV) for

smaller door height available.

*Overlay: 16 mm (5/8")

SOFT-DOWN STAY SDS-C100

SOFT-D

OW

N STAYS

3.5×14

1-25/32”(45mm)

3-15/16”(100mm)

1-17/64”(32mm)

5-5/16”(135mm)

13/32”(10.5mm)

13/3

2” +

Ove

rlay

(10.

5mm

+ O

verla

y)

Hinge Center

1-25/32”(45mm)

4-7/32”(107mm)

5-19/32”(142mm)

1-17/64”(32mm)

13/32”(10.5mm)

13/3

2” +

Ove

rlay

(10.

5mm

+ O

verla

y)

Door Edge

SDS-C100 InstallationFor Downward Opening Door

Step 1 - Position and Install Mounting PlatesThe hinge type and the coverage a�ect the placement of the mounting plate and arm �xing plate. Please use the corresponding diagram(Fig. 1 ~2) to determine the mounting dimensions for your application. Position and install mounting plate and arm �xing plate using supplied screws.

For installation of the mounting plate on the right hand side, the arrow of “R” on the “DS” side should point upward vertically. For the left side, the arrow of “L” on the “DS” side should point upward vertically.

All diagrams(Fig. 1~2) are shown for right side mounting.

DoorHeight(inch)

Door Weight(lbs)

Min Max

10 12.2 17.211 10.9 15.612 10.0 14.313 9.2 13.214 8.6 12.315 8.0 11.516 7.5 10.817 7.1 10.118 6.7 9.619 6.3 9.120 6.0 8.621 5.7 8.222 5.5 7.823 5.2 7.524 5.0 7.225 4.8 6.926 4.6

Door Weight Range per pair

8 15.0 21.59 13.3 19.1

Weight and Door HeightThe SDS-C100 must be used taking the weight and door height into consideration. The table indicates the usable weight range per door height when using two stays. When using one stay, the weight range will be half of what is shown. For doors outside of the recommended weight range, please contact Sugatsune for the recommended lid stay.

Height

Single Knuckle Hinge Installation Drop Hinge Installation

(A)

(B)

Screw (Z)

Step 3 - Adjustment and OperationIf the lid stay is sagging (A), turn the adjustment screw(Z) at the base of the arm until the lid stay straightens (B). The lid can then be opened by pushing down gently on the lid. When the lid is opening, do not put additional pressure on the lid (to open more quickly, etc.) as it may damage the stay. If you have di�culty with operation or adjustment of the lid stay, please contact Sugatsunefor technical assistance.

Insert the “key” of the arm into the arm �xing plate. The main body must be placed at90 degrees angle against the �xing angle.

Turn the main body 90 degrees and insert the center gear of the mounting plate to the hole of the main body.

③

③ Fix the main body with the bind screw.

①

①

②

②

Step 2 - Install the Main Body

6.6

18101 Savarona Way, Carson, CA 90746(310) 329-6373 Toll Free (800) 562-5267 Fax (310) 329-0819www.sugatsune.com