Solar Carport System...2015/12/30 · Mibet (Xiamen) New Energy Co., Ltd. No 69, Xintian Rd., Jimei...

Mibet (Xiamen) New Energy Co., Ltd.

No 69, Xintian Rd., Jimei District, Tel: +86592 3754999

Xiamen, China 361022 Fax: +86 592 6771575

www.mbt-energy.com Email: [email protected]

1

MRac Solar Carport System

Installation Guide

Content 1 Product Introduction ------------------------------------------P2

2 Installation Tool & Components-------------------------------P3

3 Installation Procedure -----------------------------------------P4

4 Warranty--------------------------------------------------------P8



Xiamen, China 361022 Fax: +86 592 6771575


2

1. Product Introduction

MRac Carport System is uniquely designed applying to large scale

commercial and utility system, offering shades to your cars while much

environment-friendly.

Please read this Installation Guide thoroughly before installing the MRac

Carport system. This Guide offers the planning and installation

instruction for MRac Carport.

MRac Carport products, when installed in accordance with this guide,

will be structurally adequate and will meet the local standards. During

installation, especially when working on the roof, be sure to observe the

appropriate safety regulations and please pay attention to the relevant

regulations of your local region. Please check that you are using the

current version of the installation manual by contact Mibet Energy by

mail on [email protected], or your local representative.

The installer is solely responsible for:

Complying with all applicable local or national building codes,

including any that may supersede this manual;

Ensuring that MRac and other products are appropriate for the

particular installation and the installation environment;

Using only MRac parts and installers-supplied parted as specified by

MRac (Substitution of parts may void the warranty and invalidate the

letter of certification on page 2);

How to recycle: according to the local relative statute;

How to disassemble: countermove with installation;

Ensure that there are no less than two professional workers in panel

installation;

Ensure the installation of relative electrical equipment is

performance by professional electrician.

Ensure safe installation of all electrical aspects of the PV array.



Xiamen, China 361022 Fax: +86 592 6771575


3

2. Installation Tool & Components

2.1 Installation Tool

L-Inner Hexagon

Spanner

Monkey Spanner Socket Wrench Electric Tool

Nylon Wire Tape Square Marker

2.2 Components List

Components List

Full-edge End Clamp Kit

U27 Inter Clamp Kit Rail 115 Rail 115 Connector

Beam 100 Beam 100 Connector C Clamp Kit Carport T-shape Jointer Kit



Xiamen, China 361022 Fax: +86 592 6771575


4

Carport Basement 80*80 Square Tube

2.3 Carport System Overview

（1）Full-edge End Clamp Kit （2）U27 Inter Clamp Kit

（3）Rail 115 （4）C Clamp Kit （5）Beam 100

（6) Carport T-shape Jointer Kit

（7）Carport Basement （8）80*40 Square Tube

②

①

③

④

⑤

⑥

⑦

⑧



Xiamen, China 361022 Fax: +86 592 6771575


5

3. Installation Guide

3.1 Install Each Unit

3.1.1

Fix the Carport

Basements onto the

pre-made concrete

bases according to the

technical drawing

provided, place the

nuts without fastened;

make sure all the

Carport Basements are

in a line both vertical

and landscape by a

Nylon Wire.

Showed as Drawing 1,

2, 3, and 4.

Nylon Wire

All basements have to be in

a line vertically

Nylon Wire

All basements have to

be in a line landscape

Drawing 1 Drawing 2

Drawing 3

Drawing 4



Xiamen, China 361022 Fax: +86 592 6771575


6

3.1.2

(1). Pre-assemble the

C Clamp Kit 150 onto

the T-shape Carport

Jointer by M8*25

bolts, as Drawing 5.

(Don’t fasten the

bolts tightly for the

convenience of next

step)

(2). Slide the

pre-assembled

T-shape Carport

Jointer to the

planned position on

the Beam 100, then

fasten the bolts

tightly now. Showed

as Drawing 6&7.

(3). Assemble the 80

Square Tube onto

the T-shape Carport

Jointer by M20*130

bolts.

Showing as Drawing

8&9.

Drawing 5

Drawing 6

Drawing 7



Xiamen, China 361022 Fax: +86 592 6771575


7

(4). Connect the

pre-assembled

Beam 100 Support

with the Carport

Basements, which

have already been

installed onto the

concretes, by

M20*130. 3 to 4

experienced worker

need to cooperate

to finish this step as

Drawing 10&11

showed.

Note: Make sure all

the bolts in this

system are

assembled from the

same direction as

showing in Drawing

12.

Drawing 8

Drawing 9



Xiamen, China 361022 Fax: +86 592 6771575


8

Drawing 10

Drawing 11

Keep all the nut in the same

direction for the whole system

Drawing 12



Xiamen, China 361022 Fax: +86 592 6771575


9

(5). Repeat above step

as per the technical

drawing suggested till

the whole system

finished.

Note: Make sure all

the bolts should be

fastened tightly.

3.2 Install Rail

3.2.1

The drawings

shows how the

Cross Module

being installed,

which is the main

component in C

Clamp Kit, Inter

Clamp Kit and End

Clamp Kit.

3.2.2

Check the length

of Rail 115, using

the Rail 115

Connector to

extend it

according to the

technical drawing

before assembled

onto the Beam.

8pcs of bolts are

required for each

side, totally 16pcs

bolts for one Rail

115 Connector.

Note: Not

recommend

extending the Rail

Rail

115

Rail 115

Connector

Drawing 13



Xiamen, China 361022 Fax: +86 592 6771575


10

115 after

assemble the Rail

115 onto the

Beam.

3.2.3

Assemble Rail 115

onto the Beam

according to the

technical drawing,

a marker can be

used to mark the

right position, as

Drawing showed.

3.2.4

Assemble all the

Rail 115 as

planned.



Xiamen, China 361022 Fax: +86 592 6771575


11

3.2.5

Fix the Rail 115

onto the Beam by

C Clamp Kits,

fasten all M8

inner hexagon

bolts.

Note: 2 sets of C

Clamp Kits need

to be used in

each side as

showed.

3.2.6

Repeat above step

and get all Rail 115

assembled as

technical drawing

planned, make

sure the end of all

rails in a line.

Note: All bolts

have to be

fastened tightly.



Xiamen, China 361022 Fax: +86 592 6771575


12

3.3 Install Panels

3.3.1

a. Place the

panels according

to technical

drawing (Drawing

1: Section view),

fix the panel by

Full-edge End

Clamp Kit and

U27 Inter Clamp

Kit.

b. Repeat above

step, and make

sure all the

panels are being

installed

properly.

Drawing 1: Section view

Installation of End

Clamp Kit



Xiamen, China 361022 Fax: +86 592 6771575


13

3.3.2

Installation

completed, check

all the bolts have

been fastened.

Installation of Inter Clamp Kit

No slot should be

remained between two

rows



Xiamen, China 361022 Fax: +86 592 6771575


14

4．Warranty Declaration 15 year limited Product Warranty, 5 year limited Finish Warranty

Mibet (Xiamen) New Energy Co., Ltd. (hereinafter as “Mibet Energy”) warrants to

the original purchaser (“NSEW Trading Pty Ltd.”) of products that it manufactures

(“Solar PV Mounting Systems”) at the original installation site that the Product shall

be free from defects in material and workmanship for a period of fifteen (15) years,

except for the under normal atmospheric conditions for a period of five (5) years,

from the earlier of 1). The date the installation of the Product is completed, or 2). 30

days after the purchase of Product by the original Purchaser (“Finish Warranty”).

The Finish Warranty does not apply to any foreign residue deposited on the finish. All

installations in corrosive atmospheric conditions are excluded. The Finish Warranty is

VOID if the practices specified by AAMA 609 & 610-02 –“Cleaning and

Maintenance for Architecturally Finished Aluminum” (www.aamanet.org) are not

followed by Purchaser. This Warranty does not cover damage to the Product that

occurs during its shipment, storage, or installation.

This Warranty shall be VOID if installation of the Product is not performed in

accordance with Mibet’s written installation instructions, or if the Product has been

modified, repaired, or reworked in a manner not previously authorized by Mibet IN

WRITING, or if the Product is installed in an environment for which it was not

designed. Mibet shall not be liable for consequential, contingent or incidental

damages arising out of the use of the Product by Purchaser under any circumstances.

If within the specified Warranty periods the Product shall be reasonably proven to be

defective, then Mibet shall repair or replace the defective Product, or any part thereof,

in Mibet’s sole discretion. Such repair or replacement shall completely satisfy and

discharge all of Mibet’s liability with respect to this limited Warranty. Under no

circumstances shall Mibet be liable for special, indirect or consequential damages

arising out of or related to use by Purchaser of the Product.

In addition to our Warranty against Defects, the Frame also comes with guarantees

that cannot be excluded under the Australian Consumer Law (Consumer Guarantees).

In the event that the Frame fails to satisfy a Consumer Guarantee, you are entitled to a

replacement or refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the Frame repaired or

replaced if the Frame fails to be of acceptable quality and the failure does not amount



Xiamen, China 361022 Fax: +86 592 6771575


15

to a major failure. Please note that in addition to the rights and remedies set out in this

document, you may also have other rights and remedies available to you under the

law.

*Manufacturers of related items, such as PV modules and flashings, may provide

written warranties of their own. Mibet’s limited Warranty covers only its Product, and

not any related items.

Making a claim

If you believe that the Frame is defective and you are an End-User, you may either

make a claim against the installer or builder from whom you purchased the Frame or

you may make a claim against us directly. In order to make a claim against us, you

must post, fax or email us a notice, using the contact details set out below.

In your notice you must provide: details of why you believe the Frame is defective; a

copy of your invoice, receipt or any other document which provides proof of

purchase;

Details of any expenses you have incurred in making your claim; and details of how

we should contact you.

Within a reasonable time after receipt of your claim we will contact you to arrange a

time to attend the premises at which the Frame is located.

Jurisdiction

Our Warranty against Defects is to be construed in accordance with the laws of

Victoria and any disputes will be determined by the exclusive jurisdiction of the

courts of Victoria.

Contact Details

NSEW Trading Pty Ltd

Level 5, 24 Albert Road

South Melbourne Vic 3205

Tel: 0417 387673

Email: [email protected]

Date post:	05-Jul-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

Solar Carport System...2015/12/30 · Mibet (Xiamen) New Energy Co., Ltd. No 69, Xintian Rd., Jimei...

Documents