WALL CARE PUTTY

VIJAYWHITE

Vijay White Wall Care Putty is a specially formulated powder putty with unique

raw materials & additives.

1 Kg 20 Kg 40 KgPACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White lump-free powderDrying time Initial = 40 – 60 min Final = 4 – 6 hoursPot Life ofthinned material 1 – 1.5 hours Tensile adhesion > 1.0 N/mm2 after 28 days

Water retentivity > 98% Tapped density 1.5 – 1.7 g/ccRecoatability 2 – 3 hoursUSESInterior & Exterior plastered surfacesI concrete, rendered wall, hollow block, precast walls, concrete ceilings,aerated light-weight blocks.BENEFITSExcellent whiteness & smooth finishI Excellent workability and ease of application I Prevents water leakageI Prevents growth of algae and fungusI Provides ideal base for painting I Never peels off I Provides good breathabilityI Anti-flaking I No blisteringI No chalking I No curing required.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protectfrom direct sunlight.Recommended Dilution1st coat = 40% v/w dependingon surface conditions 2nd coat = 45 - 50% v/w dependingon surface conditions

COVERAGE2 sq.mtr / kg / 2 coats on well prepared substrate.DIRECTIONS OF USEClean the surface with emery paper,putty blade or wire brush. Moisten the wall with clean water. There should be no dirt, oil traces or algae on the surface I Mix the putty with 40 % water by volume to Vijay White to prepare a uniform paste. Add the water gradually. Stir the mix thoroughly to avoid formation of lumps. Let it rest for 10 minutes. Give the paste a good mix once more I Apply first coat of putty starting from the bottom of the wall in an upward direction uniformly using a putty knife I Allow it to dry for 2 -3 hours and then rib the surface gently with fine emery paper to remove loose particlesI Apply the second coat with fresh material and maintain the total thicknessof the two coats to about 1.5 mmI Allow it to dry for at least 10 – 12 hours.NOTENot recommended for paintedor non-cementitious surfacesI Ensure the material is mixedhomogenously with waterI Once the putty paste is hardened,it should not be softened by the additionof water and applied on the wall.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of waterI Keep out of reach of children.

M-Sand Boozter is a chloride-free, synthetic polymer-based cement enhancer which allows replacing river sand with M-Sand completely

for plastering, concrete and brick works.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquid Colour Dark brown Specific gravity @ 27°C 1.25 ± 0.05 Non-volatile content 35 ± 3 % pH 10 ± 3 USESCement brick works, cement plaster and cement concrete I Ready mix concrete, concrete piles, and precast concrete I Dams, bridges, tunnels, fly-overs, canals and sea shore projects I Foundations, floor slaps, walls, columns, beams, ceilings, balconies, etc I All slender components with heavy reinforcement.BENEFITSEffectively helps replace river sand I While plastering, smooth and ease of application by locking the pores I Increases in compressive strength and plasticity I Development of early strength, workability, slump retention and setting time I Reduction of cement content, cracks, creeps and shrinkage I Reduction of cost and time of construction and amount of labour required.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.ADVANTAGESDevelopment of early strength, workability, slump retention and setting time. I Reduction of cost and time for construction and the amount of labour required.RECOMMENDED DOSAGE200 ml / 50 kg of cement. DIRECTIONS OF USECement, sand and other aggregates are mixed with 90-95% of required water for 2-3 minutes I The recommended quantity of M-Sand Boozter is measured and added to the balance 5-10% of water and added to wet concrete I This mixture is mixed thoroughly for further 2-3 minutes to get a homogenous mix.NOTEDo not add M-Sand Boozter directly to dry mix I Maintain water-cement ratio as low as possible I Do not increase the dosage of M-Sand Boozter beyond the recommended level I Over dosage may lead to delay in setting time.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

M SAND BOOZTERM SAND LUBRICATOR

200 ml 1 Lt 5 Lt 20 Lt

SUPER PLASTICISER

Flow Faast is a chloride-free super plasticiser which allows mixing water to be reduced

considerably and enhances the concrete strength significantly, particularly at early stages.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Wine red/dark brownSpecific gravity @ 27°C 1.05 – 1.15Non-volatilecontent 15 ± 3 %ph 9-13Water reduction Max 20%USESReady mix concrete, concrete piles and precast concrete I Dams, bridges, tunnels, fly-overs, canals and sea shore projects I Foundations, floor slaps, walls, columns, beams, ceilings, balconies, etc I All slender components with heavy reinforcement.BENEFITSIncreases in compressive strength and plasticity I Reduces water to cement ratio by about 20% and significantly reduces water permeability I Development of early strength, workability, slump retention and setting time I Reduction of cement content, cracks, creeps and shrinkage I Reduction of cost and time of construction and amount of labour required I Provides faster mould release and increases bonding to reinforcement steels I Improvesflow up to 120 mm slump test.

SHELF LIFE & STORAGEBest before 12 monthsin an unopened, undamaged,originally sealed packing and if storedin dry conditions I Protectfrom direct sunlight.Recommended Dilution100 – 200 ml / 50 kg of cement.DIRECTIONS OF USECement, sand and other aggregates are mixed with 90-95% of required water for 2-3 minutesI The recommended quantityof Flow Faast is measured and addedto the balance 5-10% of water and added to wet concrete I This mixture is mixed thoroughly for further 2-3 minutes to get a homogenous mix.NOTEDo not add Flow Faast directly to dry mix I Maintain water-cementratio as low as possible I Do not increase the dosage of Flow Faast beyond the recommended level I Over dosage may lead to delay in setting time.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

FLOW FAAST

1 Lt 5 Lt 20 Lt

Veco Latex is a rubberised polymer, specifically designed for use with cement formulations,

in making cement modified coatings, polymer modified mortars and concrete.

PACKAGING

SUPER LATEX POLYMER

250 ml 500 ml 1 Lt 3 Lt 5 Lt

VECOLATEX

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquidColour Milky WhiteSpecific gravity @ 27°C 1.00 ± 0.10Non-volatile content 35.00 ± 3.00% pH range 8 – 10USESFor concrete repair, particularly those concrete structures which are damaged due to Corrosion of reinforcement I Bridge deck overlays and cement patching work I Waterproofing treatment I For bonding old to new concrete I As an admixture for making polymer modified mortar & concrete I For fixing tiles I Abrasion resistant and anti-corrosive floor.BENEFITSWaterproofing I Corrosion inhibition I Protects surface from attack of salty petre I Universal repair product.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGEWaterproofing 1 part Veco Latex : 4 or bonding coat part water : 6 part CementRepair, 1 part Veco Latex: 4 part plastering and Water : Cement & Sand sealing mortar as requiredAbrasion resistant Add 5 to 10% by weight flooring of cementDIRECTIONS OF USEThe surfaces must be be clean and free from oil, grease, dust, rust, etc I Prepare Veco Latex solution by mixing it with water. Add this mixture to the required cement and sand combination to prepare cement mortar, plastering, waterproofing / bond coat, putty I Dampen the surface and apply the Veco Latex modified cementitious mixture by brush or trowel I Cure by spraying water periodically for 2– 3 days.NOTEPrepared material must be usedwithin 30 minutes I Never add Veco Latex directly to cement.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Corrosolve is a corrosion inhibiting admixture for steel reinforced concrete.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Amber colourSpecific gravity @ 27°C 1.10 – 1.20 Non-volatile content 20 – 30%pH 7 – 8USESConventional steel reinforced concrete I Parking garage decks, bridge decks and marine structures.BENEFITSPenetrates concrete and protects the rebars from corrosion I Provides effective protection against corrosion by chlorides in concrete I Enhancing the life and strength of reinforced concrete I Environment friendly I Easy to use, neutral set liquid admixture.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packing and if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE100 ml Corrosolve for 1 bag (50 kg) cement.

DIRECTIONS OF USE Dry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 75% of required water and mix for 2-3 minutes I In the remaining portion of the required water add Corrosolve. Then add thisto concrete mixer and mix for another2-3 minutes for a homogenous mixI Flow Faast and Water Seal can be added to the mixture I Cure as per the normal procedure.NOTEDo not add Corrosolve directly to dry cement or aggregate mix I Do not increase the dosage of Corrosolve than the recommended level.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with water immediately after use I Cured material can be removed mechanically.

500ml 1 Lt 5 Lt 20 Lt

CORROSOLVERUST INHIBITOR ADMIXTURE

1 Lt 5 Lt 20 Lt

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquidColour Dark brownSpecific gravity @ 27°C 1.00 – 1.10Non-volatile content 8 – 12 % pH range 5 – 7BENEFITSTime-tested and traditional method I Cost effective I Avoids crack formation I Resists water leakage I Excellent resistance to all weather conditions I Enhances the strength of concrete roof.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packing

and if stored in dry conditionsI Protect from direct sunlight.RECOMMENDED DOSAGE1 litre / for 20 litre of water.DIRECTIONS OF USEThoroughly clean the roof surface I Add 1 litre Surki Bond to 20 litre water and mix well I Mix the Surki Bond solution with recommended cement or lime, sand, brick aggregates then spread over the surface. NOTEDo not add Surki Bond directly to dry cement or aggregate mix. HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Surki Bond is a traditional weatherproof admixture which is used along with sand, aggregates, cement

or lime wash in the concrete roofs.

PACKAGING

WEATHER PROOF ADMIXTURE

SURKI BOND

Tile Plus is a specially designed pleasant paint for Kollam and Mangaluru clay roofing tiles.

It is composed of advanced polymer ingredients and is a water-soluble

environmental friendly product.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSType Solvent based Colour As per customer requirement Specific gravity @ 27°C 1.00 ± 0.05 Non-volatile content 40.00 ± 5.00%Viscosity 100 - 200 cPFinish Rich Matt Touch dry 1 hourHard dry 8 hoursOver coating interval 4 – 6 hoursUSESKollam and Mangaluru clay roofing tiles I Exterior brick works.BENEFITSRich matt finish I Good hiding property I Allows the surface to breathe and expel moisture I Colour never faded I Algae and fungal resistance I Waterproofing I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE400 ml of water per litre of cement primer.COVERAGE80 – 90 sq.ft / litre / coat. DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Dampen the surface with water I Dilute with 40% of water by volume to Tile Plus and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours with brush/rollers I After 4 – 6 hours, apply another coat I Two coats are recommended.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with proper thinner or kerosene immediately after use.

1 Lt 4 Lt 10 Lt 20 Lt

TILEPLUS

A PLEASANT PAINT FOR ROOF TILES

500 ml 1 Lt 4 Lt

Shine-Tile is a paint composed of special polymers along with technically advanced ingredients in a unique formulation for providing a high

gloss, long lasting coating.

PACKAGING

SHINETILE

ROOF CLAY TILE POLISH PAINT

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSType Solvent based Colour As per customer requirement Specific gravity @ 27°C 1.00 ± 0.05 Non-volatile content 40.00 ± 5.00%Viscosity 100 - 200 cPFinish GlossyTouch dry 1 hourHard dry 8 hoursOver coating interval 4 – 6 hoursUSESKollam and Mangaluru clay roofing tiles I Exterior brick works.BENEFITSGlossy finish I UV resistance I Dust resistance I Colour never faded I Algae and fungal resistance I Water repellent property I Ideal for wood, metal & cement surfaces.SHELF LIFE & STORAGEBest before 24 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE2 Coats.COVERAGE100 – 120 sq.ft / litre / coat. DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Prime the surfaces with V-Repel water repellent primer I Apply a single coat and allow it to dry for about 4 – 6 hours with brush/rollers I After 4 – 6 hours, apply another coat I Two coats are recommended.NOTEDon’t thin the paint with any solvent I Never apply on wet/damp surfaces.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with proper thinner or kerosene immediately after use. Cured material can be removed mechanically.

Gosana is a water-based emulsion composed of acrylic polymers and selected ingredients.

It is specially formulated to be used as floor paint, as an alternate for applying cow dung

on the floor, at the entrance of buildings.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth paste Colour Cow dung colour Specific gravity @ 27°C 1.40 ± 0.05 Non-volatile content 55.00 ± 5.00%Viscosity 3000 – 5000 cPpH 8.00 ± 1.00Finish Rich mattSurface dry 30 minutesOver coating interval 4 – 6 hoursStability of thinned paint 24 hours USESConcrete flooring I Artificial and natural stones.BENEFITSRich matt finish I Good hiding property I Abrasion resistance I Waterproofing & does not fade with weather I Very good intercoat adhesion I Can be applied by brush or rollers or spray I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE400 ml of water per litre of cement primer.COVERAGE60 – 70 sq.ft/ litre/ coat .DIRECTIONS OF USEFloor must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Application should start 4 hours after the application of Primer I Dilute with 40% of water by volume to Gosana and stir thoroughly to get homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

FLOOR PAINT

GOSANA

1 Lt 4 Lt 10 Lt 20 Lt

5 Kg

TOP COOL COAT

Solar Koat is a two component cooling coating for the roof which reduces the room temperature.

PACKAGING

SOLAR KOATPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance after mixing White, smooth pasteMix density 1.40±0.05pH 9.00±1.00Surface dry 30 minutes Over coating interval 6 hoursUSESTerraces, rooftops, parapet walls, lime terraced roofs, roof slabs I RCC, asbestos, sunshades I Exterior walls of buildings.BENEFITSIdeal for R.C.C. Asbestos, G.I. Sheets, exterior walls and pathways I Reduces power and water consumption of humidification plants I Prevents emission of highly polluting particles from asbestos sheets I Glass wool padding and false ceiling are eliminated I Cost effective.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

COVERAGE300 sq.ft / 5 kg bag / 2 coats.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Wet the surface enough prior to painting I Mix 125 ml of Solar Koat liquid into 8 litres of clean water I Add 5 kg of Solar Koat powder slowly and stir into the mixed solution I Apply the paint over the wet surface uniformly and allow it to dry completely I After 2-4 hours, apply another coat.NOTEDo not apply in hot sunlight (generally don’t paint between 10 a.m. to 5 p.m.) I Don’t mix the liquid directly to the powder I In a single shot, mix all the contents.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.