SEPARADORESNEUMÁTICOS
PROCESADO DE SÓLIDOS
PNEUMATICSEPARATORS
SOLIDS PROCESSING
EVOLUTIVE TECHNOLOGY
TECNOLOGÍA
PNEUMATICSEPARATORS
SOLIDS PROCESSING
The pneumatic separators NOVATTIA are designed
for separating fine particles (<100 µm.) present in
products demanding controlled fine particles
processing. With such an equipment, two highly
differentiated products are obtained: a flux of fine
material with a high degree of purity and a flux of
coarse material containing clearly less fine particles
than when fed.
This type of pneumatic separators work in a closed
circuit without the need of external auxiliary
equipment such as fans, cyclones or filters. The
separation circuit is totally internal which simplifies
the installation and process application.
In the pneumatic separators NOVATTIA the fed
product enters, in a controlled way, through the
upper area, onto the feeding distribution plate where
it is dispersed by means of the generated current by
the main rotor. The ascending flowing, monitored by
the positioning of the intermediate diaphragm
shovels and by the rotor’s spin rate, drags the fine
particles which will be evacuated through the
equipment’s exterior casing. The coarse particles will
be deposited in the interior body and evacuated
through the bottom area.
There are different finishing options available in virtue
of the treated product and the process’ requirements:
anti abrasive coating of specific areas, separating by
the feeding distribution plate and rotor’s drive for
processing products with a higher degree of fineness,
combining different types of discharge valves and
introducing a vibration control module for predictable
maintenance.
SEPARADORESNEUMÁTICOS
PROCESADO DE SÓLIDOS
Los separadores neumáticos NOVATTIA están
concebidos para la separación de partículas finas (<100
µm.) presentes en productos con requerimientos de
proceso de contenido en finos controlado. En un equipo de
este tipo se obtienen dos productos marcadamente
diferenciados: un flujo de material fino de alta pureza y un
flujo de material grueso con un contenido en finos
claramente inferior al presente en la alimentación.
Este tipo de separadores neumáticos trabajan en circuito
cerrado sin requerir de ningún equipamiento externo
auxiliar como ventiladores, ciclones o filtros. El circuito de
separación es totalmente interno con lo cual se simplifica la
instalación y aplicación en proceso.
En los separadores neumáticos NOVATTIA el producto
alimentado, de forma controlada, por la zona superior entra
al plato repartidor el cual dispersa el material sobre la
corriente generada por el rotor principal. El fluido
ascendente, regulado por el posicionamiento de las palas
del diafragma intermedio y por la velocidad de giro del
rotor, arrastra las partículas finas que serán evacuadas a
través del encamisado exterior del equipo. Las partículas
gruesas se depositarán en el cuerpo interior y son
evacuadas por la zona inferior.
Existen distintas opciones de acabado en función del
producto a tratar y de los requerimientos del proceso:
recubrimiento en materiales antiabrasivos de zonas
específicas, separación del accionamiento del plato
distribuidor y del rotor para tratamiento de productos con
mayor finura, combinación de distintos tipos de válvulas de
descarga e implantación de módulo de control de
vibraciones para mantenimiento predictivo.
SEPARADORES NEUMÁTICOSPNEUMATIC SEPARATORS
15 21 25 28 31 38 42 49
A 1900 2250 2600 2800 3130 3650 4000 4600
B 600 950 1200 1400 1620 1700 1900 2200
C 600 600 600 750 750 950 950 950
D 1500 2100 2500 2800 3100 3800 4200 4900
E 1800 2450 2900 3200 3600 4250 4700 5440
L 3100 3800 4400 4950 5500 6350 6850 7750
H 1400 1800 2000 2400 2600 2900 3200 3600
S kW 11 15 22 30 37 45 75 110
D kW 7.5 11 15 22 30 37 55 90
D kW 4 7.5 11 15 18.5 22 30 37
A
E
ØD
L
H
CB
EVOLUTIVE TECHNOLOGY
TECNOLOGÍA
POWERPOTENCIA
MINIMUMMÍNIMO
SECONDARY POWERPOTENCIA SECUNDARIA
MAIN POWERPOTENCIA PRINCIPAL