Solution 880 Operators Manual - Security Strategies Solution 880 user guide.pdf · Introduction...

Solution 880Operators Manual

Issue 1.00

Solution 880Operators Manual

Copyright 1998 by Electronics Design and Manufacturing Pty Limited,

SYDNEY, AUSTRALIA

Document Part Number MA408O

Document ISSUE 1.00

Printed 15 June 1998

This documentation is provided to suit Solution 880 Control Panel (CC408)

Firmware Revision 1.00

Hardware Revision A

Copyright Notice

All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrievalsystem in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,without the prior written permission of Electronics Design and Manufacturing Pty Limited.

Trademarks

Throughout this document trademark names may have been used. Rather than put a trademark symbolin every occurrence of a trademark name, we state that we are using the names only in an editorialfashion and to the benefit of the trademark owner with no intention of infringement of the trademark.

Notice of Liability

While every precaution has been taken in the preparation of this document, neither Electronics Designand Manufacturing Pty Limited nor any of its official representatives shall have any liability to anyperson or entity with respect to any liability, loss or damage caused or alleged to be caused directly orindirectly by the information contained in this book.

Electronics Design and Manufacturing Pty Limited reserves the right to make changes to features andspecifications at any time without prior notification in the interest of ongoing product development andimprovement.

Table Of Contents

Introduction........................................................................................................................................ 7

Features.............................................................................................................................................. 7

Basic System Operation...................................................................................................................... 8

Code Retries........................................................................................................................................ 9Codepad Lockout Time .............................................................................................................................. 9

Codepad Extinguish Mode ................................................................................................................. 9

Alarm Memory ................................................................................................................................... 9

Sensor Watch Time .......................................................................................................................... 10

Day Alarm ........................................................................................................................................ 10Day Alarm Resetting................................................................................................................................. 10

Day Alarm Latching ................................................................................................................................. 10Operation...............................................................................................................................................................10

Entry Time........................................................................................................................................ 11

Exit Time.......................................................................................................................................... 11

System Date and Time ...................................................................................................................... 11User Codes 1 - 16 ...................................................................................................................................... 11

User Codes 9 – 16...................................................................................................................................... 11User Code Priority..................................................................................................................................................12

System Indicators and Operations ........................................................................................................... 14

CP5 Eight Zone Codepad ......................................................................................................................... 14Zone Indicators ......................................................................................................................................................14AWAY Indicator....................................................................................................................................................14STAY Indicator......................................................................................................................................................14MAINS Indicator ...................................................................................................................................................15FAULT Indicator ...................................................................................................................................................15Audible Indicators..................................................................................................................................................15

CP5 Eight Zone LCD Codepad......................................................................................................... 16Zone Indicators ......................................................................................................................................................16AWAY Indicator....................................................................................................................................................16STAY Indicator......................................................................................................................................................16System Disarmed ...................................................................................................................................................17MAINS Indicator ...................................................................................................................................................17Zone Isolating Mode ..............................................................................................................................................17FAULT Indicator ...................................................................................................................................................17Programming Mode................................................................................................................................................17Off Indicator/Zone Sealed ......................................................................................................................................18On Indicator/Zone In Alarm ...................................................................................................................................18Audible Indicators..................................................................................................................................................18

System Operations ............................................................................................................................ 19Arming The System In AWAY Mode ...................................................................................................... 19

Disarming The System From AWAY Mode ............................................................................................ 19

Arming The System In STAY Mode 1 .............................................................................................. 20Disarming The System From STAY Mode 1 ........................................................................................... 21

Arming The System In STAY Mode 2 ..................................................................................................... 21

Disarming The System From STAY Mode 2 ........................................................................................... 22

Codepad Functions........................................................................................................................... 22

Isolating Zones ................................................................................................................................. 23Standard Isolating..................................................................................................................................... 23

Code To Isolate ......................................................................................................................................... 23

Fault Analysis Mode .........................................................................................................................24Fault Descriptions ..................................................................................................................................... 24

Low Battery........................................................................................................................................................... 24Date and Time ....................................................................................................................................................... 25Sensor Watch......................................................................................................................................................... 25Horn Speaker Monitor ........................................................................................................................................... 25Telephone Line Fault ............................................................................................................................................. 25E2 Fault ................................................................................................................................................................. 25Codepad Fuse Fail ................................................................................................................................................. 25Communication Failure.......................................................................................................................................... 25AC Mains Failure .................................................................................................................................................. 25

Codepad Duress Alarm............................................................................................................................. 26

Codepad Panic Alarm............................................................................................................................... 26

Codepad Fire Alarm ................................................................................................................................. 26

Codepad Medical Alarm........................................................................................................................... 26

Remote Radio Transmitter Operation ...............................................................................................27Arming Via Transmitter In AWAY Mode .............................................................................................................. 27Disarming Via Transmitter From AWAY Mode ..................................................................................................... 27Arming Via Transmitter In STAY Mode ................................................................................................................ 27Disarming Via Transmitter From STAY Mode ....................................................................................................... 28Panic Alarm Via Transmitter.................................................................................................................................. 28

Operating Remote Outputs Via Transmitter........................................................................................... 28

Master Code Functions.....................................................................................................................29Arm Or Disarm Both Areas At The Same Time...................................................................................................... 29Changing and Deleting User Codes ........................................................................................................................ 30Changing and Deleting Radio Remote User Codes ................................................................................................. 32Changing Domestic Phone Numbers ...................................................................................................................... 33Changing Telco Arm/Disarm Sequence .................................................................................................................. 34Setting STAY Mode 2 Zones ................................................................................................................................. 36Turning Outputs On/Off......................................................................................................................................... 37Setting The Date and Time..................................................................................................................................... 38Walk Test Mode .................................................................................................................................................... 38Event Memory Recall Mode................................................................................................................................... 39

User Code Functions – Partitioned Systems Only.............................................................................40Arm Or Disarm Both Areas At The Same Time...................................................................................................... 40

Hold Down Functions ............................................................................................................................... 41Arm The System In AWAY Mode ......................................................................................................................... 41Arm The System In STAY Mode 1 ........................................................................................................................ 41Arm The System In STAY Mode 2 ........................................................................................................................ 41Horn Speaker Test ................................................................................................................................................. 41Bell Test ................................................................................................................................................................ 41Strobe Test ............................................................................................................................................................ 42Turning Day Alarm On and Off.............................................................................................................................. 42Fault Analysis Mode .............................................................................................................................................. 42Initiate A Modem Call ........................................................................................................................................... 42Reset Latching Outputs .......................................................................................................................................... 42Codepad ID and Beeper Tone Change .................................................................................................................... 43Initiate A Test Report............................................................................................................................................. 43

Partitioning.......................................................................................................................................44

Communication Options ...................................................................................................................45Remote Arming Via The Telephone......................................................................................................... 46

Domestic Dialling Reporting..................................................................................................................... 46

Basic Pager Reporting .............................................................................................................................. 47

Optional Equipment..........................................................................................................................48Glossary Of Terms.................................................................................................................................... 50

Warranty........................................................................................................................................... 52Limitations.............................................................................................................................................................52Maintenance...........................................................................................................................................................52Specifications.........................................................................................................................................................53Quality Policy ........................................................................................................................................................53Advice To Users.....................................................................................................................................................54New Zealand Telepermit Notes...............................................................................................................................54

Installation Notes ............................................................................................................................. 55

Service Notes .................................................................................................................................... 57

Index................................................................................................................................................. 58

IntroductionCongratulations on selecting the Solution 880 control panel to protect you and your property. Sothat you can obtain the most from your unit, we suggest that you take the time to read through thismanual and familiarise yourself with the numerous outstanding operating features of this system.

You will notice that in all aspects of planning, engineering, styling, operation, convenience andadaptability, we have sought to anticipate your every possible requirement. Programming simplicityand speed have been some of the major considerations and we believe that our objectives in this areahave been more than satisfied.

This manual will explain all aspects of operating the control panel. All system parameters and optionsare detailed, however suitability is left up to the individual. Every system can be tailored to meet allrequirements quickly and easily.

The Solution range of control panels are very popular with thousands of people throughout manycountries of the globe, all of whom have various levels of technical aptitude and ability. We have triedto aim this manual at all levels of readers.

FeaturesThe Solution 880 control panel uses the very latest in microprocessor technology to provide youwith more useful features and superior reliability and performance.

Following is a list of the main features that the control panel will provide.

• Sixteen Programmable User Codes • Eight Radio Remote User Codes

• STAY Mode and AWAY Mode Operation • Entry and Exit Warning Beeper

• Eight Programmable Burglary Zones • Partitionable To 2 Areas

• Siren and/or Dialler Lockout Per Zone • Dual Reporting

• Delayed Reporting • Telco Arm/Disarm Sequence (Call Forwarding)

• Built In Telephone Line Fail Monitor • Sensor Watch

• Day Alarm • Dynamic Battery Testing

• Remote Arming • Automatic Arming and Automatic Disarming

• Answering Machine Bypass • AC Fail and System Fault Indicators

• Event Memory Recall • Walk Test Mode

• Upload/Download Programmable • Monitored Siren Output (Output 1)

• Auxiliary Output (Output 2) • Strobe Output

• Relay Output • EDMSAT – Satellite Siren Compatible

• Separate Fire Alarm Sound

Solution 880 Operators Manual 7

Electronics Design and Manufacturing Pty Limited ISSUE100.DOC

One option that can be programmed by your installer will prevent another installer ortechnician from performing any service to your system. This should be discussed withyour installer.

Refer to “Optional Equipment” on page 48 for more information on accessories and other features thatcan be used with your system.

Basic System OperationThe overall purpose of your alarm system is to deter any would be intruder from entering yourpremises.

Before leaving your home or office, make sure all windows and doors are closed. Enter yourdesignated code followed by the AWAY button. Your alarm system will now arm in AWAY Modeand commence counting down the exit time.

After the exit time has expired, you will hear one long beep at the remote codepad to indicate that thesystem has been armed in AWAY Mode. Any unsealed zones will be automatically isolated. Thecontrol panel is now ready to activate the sirens and strobe lights should an alarm occur.

If a zone that is sealed has triggered after exit time has expired, a number of events will occur.Following is a typical sequence of events.

1. The control panel will activate any audible devices such as sirens, flashing blue strobe light andthe communications dialler.

2. The communication dialler will transmit all relevant alarm information via the telephone linealerting the respective persons of the current state of events.

3. The siren timer will commence counting down as soon as an alarm occurs. When the siren runtime expires, the siren will automatically reset and be placed into a ready state for the next alarm.

4. Upon your return, the blue strobe light may still be operating to inform you that there has beenan alarm.

5. One or a number of zone indicators will be flashing, allowing you to identify the particularzone(s) that caused the alarm condition.

This is a very basic outline of the general system operation. As there are many features available inthe Solution 880 control panel, there could be numerous variations from the above sequence.

8 Solution 880 Operators Manual

ISSUE100.DOC Electronics Design and Manufacturing Pty Limited

Code RetriesCode retries restricts the amount of times an invalid user code can be used in an attempt to operate thesystem. An alarm caused by this is known as a "Codepad Tamper Alarm". When a codepad tamperalarm occurs, the system will carry out the following events;

1. Activate the sirens and strobe connected to the control panel. Contact your installer if yourequire this to be silent.

2. Shutdown all codepads that are connected and automatically disable them from operating thesystem. Your installer programs the length of time they are disabled for. Refer to "InstallationNotes" on page 55 for the length of time the codepad/s will be shut down for.

3. Send an "Access Denied" report to the base station receiver (Optional).

This function operates when the system is in the armed or disarmed state. Each time the system isarmed or disarmed, the code retry counter will be reset. The number of incorrect code attempts can beanywhere between 1 to 15. This value is programmed by your installer. Refer to "Installation Notes"on page 55 for the number of code retries set by your installer.

Codepad Lockout TimeThe codepad will be locked out for the time programmed by your installer if the wrong code has beenentered more times than allowed by the code retry attempts.

Codepad Extinguish ModeThis option when programmed by your installer will allow the indicators on your codepad toautomatically extinguish when the codepad is not used for a period of sixty seconds.

The indicators will illuminate once a button has been pressed on the remote codepad, when an alarmhas occurred or when the systems entry time has been activated. The indicators will not illuminatewhen a silent alarm has been triggered. This option can only be programmed by your installer.

Alarm MemoryIf you return to your premises and you notice the strobe light flashing, then care should be taken as thisindicates that there has been an alarm condition while you were away.

When you enter the building and disarm the system, you will notice one or a number of zone indicatorsflashing rapidly. This indicates that the zone(s) in question have triggered into alarm.

You should take note of this information so that it can be passed onto your installer should they requireit.

It is also possible to interrogate your alarm system using the event memory recall function. This willallow you or your installer to interpret the exact sequence of events that had occurred. Refer to “EventMemory Recall Mode” on page 39 for more information.



Sensor Watch TimeSensor watch is part of the control panel's watchdog circuitry. It is a feature designed to ensure that allyour detection devices are working correctly.

Sensor watch time determines how many days (0-99) a zone may remain sealed before registering as afault. This feature is only active while the system is in the disarmed state because while your system isarmed, the detection devices are on stand-by waiting to be activated.

If a zone programmed for sensor watch has not triggered and reset during this time, the FAULTindicator will illuminate and the codepad will beep once every minute. To cancel the codepad beepingonce every minute, press the AWAY button. Refer to "Fault Analysis Mode" on page 42 for moreinformation. Refer to "Installation Notes" on page 55 for the sensor watch time set by your installer.

Day AlarmDay alarm may be used to monitor the front door of a shop or a pool gate. Day alarm enables acombination of zones to be monitored while the system is in the disarmed state. An indication isavailable via any of the programmable outputs including the codepad buzzer. Only zones 1 - 4 may beused as day alarm monitored zones. Refer to the "Installation Notes" on page 55 to check which zoneshave been allocated to operate for day alarm.

Day Alarm ResettingAn output that has been programmed for day alarm resetting will operate when a zone selected for dayalarm is triggered. The output will reset when the zone returns to normal. This can only occur whenthe system is disarmed.

Day Alarm LatchingAn output that has been programmed for day alarm latching will operate when a zone selected for dayalarm is triggered. The output will reset when the AWAY button has been pressed. This can onlyoccur when the system is disarmed.

ExampleIf you have multiple zones programmed for day alarm and one of them has triggered, it is difficult toknow which zone caused the day alarm. Using the option of day alarm latching will solve thisproblem. When a day alarm zone triggers, all zone indicators are turned off leaving only the zone orzones that caused the day alarm illuminated. To clear the day alarm memory, press the AWAY button.

OperationDay alarm is turned on and off by holding the 4 button down for two seconds. Refer to "Hold DownFunctions" on page 41 for more information. Three beeps indicate that day alarm is turned on and twobeeps indicate that day alarm is turned off.

If a zone has been programmed for day alarm, it can be isolated in the normal way. The isolated zonetherefore will not register as a day alarm zone.



Entry TimeEntry time is the amount of time allowed to disarm your system after you have opened the entry delayzone. During the entry time, the codepad buzzer will beep twice per second warning you to disarmyour system. An alarm will activate if you do not disarm your system before the entry time expires.Refer to "Installation Notes" on page 55 for the entry time set by your installer.

Exit TimeExit time is the amount of time you have to leave your premises after you have entered your code toarm the system. You will hear a long beep from the codepad to indicate the end of exit time. Makesure you exit your premises before this time expires. Refer to "Installation Notes" on page 55 for theexit time set by your installer.

System Date and TimeThe control panel has a real time 12 month calendar and 24 hour clock that needs to be set andchanged for daylight savings. This will allow the system to log events and send test reports withaccurate time and date stamping if programmed. Refer to “Setting The Date and Time” on page 38 formore information on setting the date and time.

User Codes 1 - 16The purpose of user codes is to arm and disarm the system as well as perform other specific functionsas described in “User Code Priority” on page 12.

User codes can be any length between one to four digits long. Each user code can have a differentpriority level allocated to it. This controls the behaviour of the code, allowing it to arm only or to armand disarm etc.

There are a total of 16 user codes available that can be changed or deleted at any time by the MasterCode holder. Multiple Master Codes may be programmed. Refer to “” on page 30 for more information on adding, deleting or changing user codes.

The priority level for each user code can only be programmed or changed by the installer.

User Codes 9 – 16The control panel has the ability to be remotely armed and disarmed via remote radio transmitters. Upto eight remote user codes may be allocated for radio transmitter operation. Before the control panelwill accept radio On/Off signals, you must teach the control panel which transmitter is used for eachuser code. User codes 9 – 16 can have both a user code and a remote radio user code allocated tothem. The user codes act as per their allocated priority level, and the radio remote codes act asarm/disarm codes only.



Teaching Radio User CodesTeaching radio user codes can only be carried out using the Master Code. Refer to “Changing andDeleting Radio Remote User Codes” on page 32 for more information.

User Code 16 will report to the monitoring company when any of the following methods for armingand disarming are used.

1. Arm and disarm via remote radio control equipment connected to the optional RadioKey/Keyswitch Interface or Night Arm Station.

2. Arm the system remotely over the telephone.

3. Automatic arming when the preset time is reached.

4. Single button arming in AWAY Mode, STAY Mode 1 or STAY Mode 2.

5. Single button disarming from STAY Mode 1 or STAY Mode 2.

User Code PriorityThere are ten different priority levels that can be allocated to the user codes. Each priority level allowsor restricts the functions that different user code holders may perform.

If user code priority levels 4, 6, 12 or 14 have been programmed to any of the available 16user codes, the method of standard isolating will no longer operate. Only those usercodes with the priority level of 4, 6, 12 or 14 will be allowed to isolate zones using themethod code to isolate.

Priority Description0 Arm and Disarm1 Arm Only2 Arm and Disarm + Open/Close Reports3 Arm Only + Close Report4 Arm and Disarm + Code To Isolate6 Arm and Disarm + Code To Isolate + Open/Close Reports8 Arm and Disarm + Master Code Functions10 Arm and Disarm + Master Code Functions + Open/Close Reports12 Arm and Disarm + Master Code Functions + Code To Isolate14 Arm and Disarm + Master Code Functions + Code To Isolate +

Open/Close Reports

Table 1: User Code Priority Levels

Arm and DisarmThis priority level allows the user code holder to arm and disarm the system.

Arm OnlyThis priority level allows the user code holder to arm the system but not disarm it.



Arm and Disarm + Open/Close ReportsThis priority level allows the user code holder to arm and disarm the system. When this priority levelis used, the control panel will send an opening and closing report to the base station.

Arm Only + Close ReportThis priority level allows the user code holder to arm the system but not disarm it. When this prioritylevel is used, the control panel will send a closing report to the base station.

Arm and Disarm + Code To IsolateThis priority level allows the user code holder to arm and disarm the system.Isolating of zones will only be allowed by using the method “Code To Isolate” once this priority levelhas been set. Refer to “Zone Isolating Mode" on page 17 for more information.

Arm and Disarm + Code To Isolate + Open/Close ReportsThis priority level allows the user code holder to arm and disarm the system. Isolating of zones willonly be allowed by using the method “Code To Isolate” once this priority level has been set. Refer to“Zone Isolating Mode" on page 17 for more information. When this priority level is used, the controlpanel will send an opening and closing report to the base station.

Arm and Disarm + Master Code FunctionsThis priority level allows arming and disarming of the system and the ability to carry out any of theMaster Code Functions described on page 23. More than one user code can be allocated to thispriority level.

Arm and Disarm + Master Code Functions + Code To IsolateThis priority level allows arming and disarming of the system and the ability to carry out any of theMaster Code Functions described on page 23.

Isolating zones will only be allowed by using the method "Code To Isolate" once this priority level hasbeen set. Refer to “Zone Isolating Mode" on page 17 for more information. More than one user codecan be allocated to this priority level.

Arm and Disarm + Master Code Functions + Code To Isolate + Open/Close ReportsThis priority level allows arming and disarming of the system and the ability to carry out any of theMaster Code Functions described on page 23.

Isolating zones will only be allowed by using the method "Code To Isolate" once this priority level hasbeen set. Refer to “Zone Isolating Mode" on page 17 for more information. More than one user codecan be allocated to this priority level.

When this priority level is used, the control panel will send an opening and closing report to the basestation.



System Indicators and Operations

CP5 Eight Zone CodepadThe codepad is the communications interface between you andyour alarm system. It allows you to issue commands and offersboth visual and audible indications that guide you through thegeneral operation.

The codepad incorporates numerous indicators. There areZONE indicators which are used to show the condition of eachzone and four other indicators for general status. The followingis a list of situations and the relevant indications that will beseen.

Figure 1: CP5 Eight Zone Codepad

Zone IndicatorsThe ZONE indicators are used to show the status of the zones. The following table lists the variouscircumstances that the indicators will display (ie. Zone Sealed, Zone Unsealed).

Indicator DefinitionOn Zone Is UnsealedOff Zone Is Sealed

Flashing Fast(0.25 Sec On – 0.25 Sec Off)

Zone Is In Alarm Condition

Flashing Slow(1 Sec On – 1 Sec Off)

Zone Is Manually Isolated

Table 2: Zone Indicators

AWAY IndicatorThe AWAY indicator is used to inform you that the system is armed in the AWAY Mode.

Indicator DefinitionOn System Is Armed In AWAY ModeOff System Is Not Armed In AWAY Mode

Table 3: AWAY Indicator

STAY IndicatorThe STAY indicator is used to indicate that the system is armed in STAY Mode.

Indicator DefinitionOn System Is Armed In STAY ModeOff System Is Not Armed In STAY Mode

Flashing System Is In Isolating Mode

Table 4: STAY Indicator



MAINS IndicatorThe MAINS indicator is used to indicate that the systems AC mains supply is normal or has failed.

Indicator DefinitionOn AC Mains Power Normal

Flashing AC Mains Failure

Table 5: MAINS Indicator

FAULT IndicatorThe FAULT indicator is used to indicate that the system has detected a system fault. Refer to “FaultAnalysis Mode” on page 42 for more information on system faults.

Indicator DefinitionOn There Is A Fault That Needs To Be RectifiedOff The System Is Normal, There Are No Faults

Flashing There Is A Fault Waiting To Be Acknowledged

Table 6: FAULT Indicator

Audible IndicatorsIn general, the audible indications emitted by the codepad are as follows:

Indicator DefinitionOne Short Beep A Button Has Been Pressed On The Codepad Or End

Of Exit Time When Armed In STAY ModeTwo Short Beeps The System Has Accepted Your Code

Three Short Beeps The Requested Function Has Been ExecutedOne Long Beep Indicates End Of Exit Time For AWAY Mode Or

The Requested Operation Has Been Denied OrAborted

One Short Beep Every Second Walk Test Mode Is ActiveOne Short Beep Every Minute There Is A Fault Waiting To Be Acknowledged

Table 7: Audible Indications



CP5 Eight Zone LCD Codepad

The codepad is the communications interface between you andyour alarm system. It allows you to issue commands and offersboth visual and audible indications that guide you through thegeneral operation.

The codepad incorporates numerous indicators. There areZONE indicators which are used to show the condition of eachzone and seven others for general status. The following is a listof situations and the relevant indications that will be seen.

Figure 2: CP5 Eight Zone LCD Codepad

Zone Indicators1 2 3 .... The ZONE indicators are used to show the status of the zones. The following

table list the various circumstances that the indicators will display (ie. ZoneSealed, Zone Unsealed).

Indicator DefinitionOn Zone Is UnsealedOff Zone Is Sealed

Flashing Fast(0.25 Sec On – 0.25 Sec Off)

Zone Is In Alarm Condition

Flashing Slow(1 Sec On – 1 Sec Off)

Zone Is Manually Isolated

Table 8: Zone Indicators

AWAY IndicatorThe AWAY indicator illuminates when the system is armed in the AWAYMode. The indicator will also illuminate when the system is armed in theAWAY Mode.

Indicator DefinitionOn System Is Armed In AWAY ModeOff System Is Not Armed In AWAY Mode

Table 9: AWAY Indicator

STAY IndicatorThe STAY indicator illuminates when the system is armed in STAY Mode 1 orSTAY Mode 2. The indicator will also illuminate when the system isarmed in STAY Mode 1 or STAY Mode 2.

Indicator DefinitionOn System Is Armed In STAY Mode 1 Or 2Off System Is Not Armed In STAY Mode 1 Or 2

Flashing System Is In Zone Isolating Mode

Table 10: STAY Indicator



System Disarmed

This indicator will illuminate when the system has been disarmed. The indicator will also illuminate when the system has been disarmed.

MAINS IndicatorThe MAINS indicator is used to indicate that the systems AC mains supply isnormal or has failed.

Indicator DefinitionOn AC Mains Power Normal

Flashing AC Mains Failure

Table 11: MAINS Indicator

Zone Isolating Mode

Flashing

This indicator will illuminate when you attempt to isolate zones. The personwill flash once every 3 seconds.

FAULT IndicatorThe FAULT indicator is used to indicate that the system has detected a systemfault. Refer to “Fault Analysis Mode” on page 42 for more information onsystem faults.

Indicator DefinitionOn There Is A Fault That Needs To Be RectifiedOff The System Is Normal, There Are No Faults

Flashing There Is A Fault Waiting To Be Acknowledged

Table 12: FAULT Indicator

Programming Mode

Flashing

This indicator will illuminate when the system has entered the operatorsprogramming mode (ie Master Code Functions). Both persons will flash.



Off Indicator/Zone SealedThe indicator will illuminate when the system is in the disarmed state andwill flash when a zone becomes unsealed. If will stop flashing when all zonesare sealed.

On Indicator/Zone In AlarmThe indicator will illuminate when the system is armed in the AWAYMode or STAY Mode 1 or STAY Mode 2 and will flash when an alarm occurs.The indicator will reset once a valid user code has been entered.

Audible IndicatorsIn general, the audible indications given out by the codepad are as follows:

Indicator DefinitionOne Short Beep A Button Has Been Pressed On The Codepad Or End

Of Exit Time When Armed In STAY ModeTwo Short Beeps The System Has Accepted Your Code

Three Short Beeps The Requested Function Has Been ExecutedOne Long Beep Indicates End Of Exit Time For AWAY Mode Or

The Requested Operation Has Been Denied OrAborted

One Short Beep Every Second Walk Test Mode Is ActiveOne Short Beep Every Minute There Is A Fault Waiting To Be Acknowledged

Table 13: Audible Indications



System OperationsThe following pages will describe how to use and interpret the many codepad functions that areavailable on the Solution 880 control panel.

Arming The System In AWAY ModeThere are two methods for arming your system in AWAY Mode.

Method OneEnter your code followed by the AWAY button. Two beeps will be heard and the AWAY indicator willilluminate. Exit time will now commence.

+

Method TwoHold down the AWAY button until two beeps are heard. The AWAY indicator will illuminate and exittime will now commence.

If a zone is not sealed at the end of exit time, the zone will be automatically isolated. The zone willbecome an active part of the system again as soon as it has resealed (ie. If a window is left open afterexit time has expired, the window will not be an active part of the system until it has closed. Openingthe window after exit time has expired will cause an alarm condition).

Single button arming in AWAY Mode will report as user code number 16.

Forced ArmingThe feature of arming the system when a zone is not sealed is known as forced arming.

If the AWAY indicator does not illuminate and a long beep is heard when you attempt to arm thesystem, forced arming is not permitted. If this is the case you must ensure that all zones are sealed ormanually isolated before you can arm the system.

Disarming The System From AWAY Mode

To Disarm The System From AWAY ModeEnter your code followed by the AWAY button.Two beeps will be heard and the AWAY indicator will extinguish. A flashing ZONE indicatorrepresents a previous alarm on that zone.

+



Arming The System In STAY Mode 1STAY Mode 1 is when the system has been armed with particular zones automatically isolated. Thesezones must be programmed by the installer.

When there is a need to arm only the system perimeter, this mode is extremely handy. It automaticallydisables the interior detection zones allowing movement within the protected area while at the sametime arming the perimeter zones.

There are two methods for arming your system in STAY Mode 1. Refer to the “Installation Notes” onpage 55 for information on which zones have been programmed for STAY Mode isolation.

Method OneEnter your code followed by the STAY button.Two beeps will be heard and the STAY indicator will illuminate. Exit time will now commence.

Any zones that have been programmed for STAY Mode 1 will be automatically isolated and theirrespective indicators will begin to flash until exit time expires. At the end of exit time, the ZONEindicators will extinguish and the codepad will give one short beep.

+

Method TwoHold down the STAY button until two beeps are heard.The STAY indicator will illuminate and exit time will now commence.

Any zones that have been programmed for STAY Mode 1 will be automatically isolated and theirrespective indicators will begin to flash until exit time expires. At the end of exit time, the ZONEindicators will extinguish and the codepad will give one short beep.

Single button arming in STAY Mode 1 will report as user code number 16.

If a zone is not sealed at the end of exit time, the zone will be automatically isolated. The zone willbecome an active part of the system again as soon as it has resealed (ie. If a window is left open afterexit time has expired, the window will not be an active part of the system until it has closed. Openingthe window after exit time has expired will cause an alarm condition).

Forced ArmingThe feature of arming the system when a zone is not sealed is known as forced arming.

If the STAY indicator does not illuminate and a long beep is heard when you attempt to arm the system,forced arming is not permitted. If this is the case you must ensure that all zones are sealed or manuallyisolated before you can arm the system.



Disarming The System From STAY Mode 1There are two methods for disarming the system from STAY Mode 1. Method one is standard and willalways operate. Method two is optional and needs to be programmed by your installer.

Method OneEnter your code followed by the STAY button.Two beeps will be heard and the STAY indicator will extinguish. A flashing ZONE indicator representsa previous alarm on that zone.

+

Method TwoA flashing ZONE indicator represents a previous alarm on that zone. If this is the case, a valid usercode will need to be used to disarm the system.

Hold down the STAY button until two beeps are heard. The STAY indicator will extinguish and thesystem will disarm.

Single button disarming from STAY Mode 1 will report as user code number 16.

Arming The System In STAY Mode 2STAY mode 2 is when the system has been armed with particular zones automatically isolated. AnyMaster Code user can program these zones before the system is armed in STAY mode 2. Refer to“Setting STAY Mode 2 Zones” on page 36 for details on how to program zones for STAY mode 2.

When there is a need to arm the perimeter of your building, this mode is extremely handy. Itautomatically disables the interior detection zones allowing for movement within the protected areawhile at the same time arming the perimeter zones.

To Arm Your System In STAY Mode 2

Hold the 0 button down until two beeps are heard.The STAY indicator will illuminate and any zones that have been programmed for STAY mode 2 will beautomatically isolated and their respective indicators will begin to flash until exit time expires. At theend of exit time the zone indicators will extinguish.

00

If a zone is not sealed at the end of exit time it will be automatically isolated. It will become an activepart of the system as soon as it is sealed (ie. If a window is opened before the end of exit time, it willnot be an active part of the system until it is closed. Opening the window after this time will cause analarm condition).

The feature of arming the system when a zone is not sealed is known as forced arming. If this featureis not suitable, your installer can program your system so that it will not arm unless all zones aresealed. If the STAY indicator does not illuminate and a long beep is heard, forced arming is notpermitted. If this is the case, you must ensure that all zones are sealed or manually isolated before youwill be allowed to arm the system.



Disarming The System From STAY Mode 2There are two methods for disarming the system from STAY Mode 2. Method one is standard and willalways operate. Method two is optional and needs to be programmed by your installer.

Method OneEnter your code followed by the STAY button. Two beeps will be heard and the STAY indicator willextinguish. A flashing ZONE indicator represents a previous alarm on that zone.

+

Method TwoA flashing ZONE indicator represents a previous alarm on that zone. If this is the case, a valid usercode will need to be used to disarm the system.

Hold down the 0 button until two beeps are heard. The STAY indicator will extinguish and the systemwill disarm.

0

Single button disarming from STAY Mode 2 will report as user code number 16.

Codepad FunctionsThe following pages will describe how to use and interpret the many codepad functions that areavailable on the Solution 880 control panel.

Most functions are performed using the Master Code. Refer to “Master Code Functions” on page 29for more information.

Before attempting to enter any of the Master Code functions, ensure that the system is in the disarmedstate and that there are no alarm memory indicators flashing. If this is not the case, the following willbe required.

1. If any of the zone indicators are flashing fast, enter your code followed by the AWAYbutton. This will reset any zone alarms that have occurred (If the system becomes armed,enter your code followed by the AWAY button a second time to disarm the system).

2. If the system has been armed in AWAY Mode, STAY Mode 1 or STAY Mode 2 (ie. TheAWAY or STAY indicator is illuminated), enter your code followed by the AWAY buttonto disarm the system.

The factory default Master Code is 2580 and can be changed at any time. Therefore, if your system’sMaster Code differs from the default, please substitute your existing Master Code in the followingexamples.

The Master Code allows you to change any user code and even the Master Code itself. The MasterCode is the only code that allows the execution of Master Code functions detailed later in this manual.



Isolating ZonesWhen a zone has been isolated, access is allowed into that zone at all times. Isolating zones isperformed by one of two methods. One way requires the use of a valid user code while the other waydoes not. The ability to isolate zones is governed by the priority level allocated to each user codeholder. Some user code holders may not be able to isolate zones. Refer to "User Code Priority" onpage 12 for further information.

Standard Isolating1. Press the STAY button twice. Three beeps will be heard.

2. * Enter the zone number required to be isolated followed by the STAY button. Thezone you have just selected to be isolated will now begin to flash.

Repeat step 2 if more than one zone is required to be isolated.

3. Press the AWAY button when finished selecting the zones to be isolated. Two beeps willbe heard.

The zones selected to be isolated will now continue to flash until the system has next been disarmed.The system is now ready to be armed in AWAY Mode.

+ + + +

* As each zone is isolated, the corresponding ZONE indicator will begin to flash. If amistake is made, press the zone number that was incorrectly entered followed by theSTAY button. This zone is now no longer isolated and the ZONE indicator willextinguish.

Code To Isolate1. Press the STAY button.

2. Enter your code.

3. Press the STAY button. Three beeps will be heard.

4. * Enter the zone number required to be isolated followed by the STAY button. The zoneyou have just selected to be isolated will now begin to flash. Repeat step 4 if more thanone zone is required to be isolated.

5. Press the AWAY button when finished selecting the zones to be isolated. Two beeps willbe heard.

The zones selected to be isolated will now continue to flash until the system has next been disarmed.The system is ready to be armed in AWAY Mode.

+ + + + +




Fault Analysis ModeWhenever a system fault occurs, the FAULT or MAINS indicator will flash and the codepad will beeponce every minute.

If the MAINS indicator is flashing, this is because the AC mains supply has been disconnected. Thereis no need to determine this type of system fault. Pressing the AWAY button once will acknowledgethe AC mains fail and will stop the codepad beeping once every minute.

To Determine The Type Of System FaultHold down the 5 button until two beeps are heard or alternatively, enter your MASTER CODEfollowed by 5 and the AWAY button.

The FAULT indicator should remain steady and the STAY and AWAY indicators should flash in unisonwith each other.

The type of system fault will be indicated by the ZONE indicators. Refer to "Table 14: Fault Indicators"for the list of different system faults that may occur.

Zone Indicator Fault Description1 Low Battery2 Date and Time3 Sensor Watch4 Horn Speaker Disconnected5 Telephone Line Fault6 E2 Fault7 Codepad Fuse Fail8 Communications Failure

Table 14: Fault Indicators

To exit fault analysis mode, press the AWAY button. The STAY and AWAY indicators will extinguishand the FAULT indicator will remain illuminated.

To Acknowledge The System FaultTo acknowledge the system fault, press the AWAY button. The FAULT indicator will remainilluminated and the codepad will cease its once a minute beep.

Fault DescriptionsLow BatteryA low battery fault will register when the battery supply voltage falls below 10.5 volts or when adynamic battery test detects a low capacity battery. This fault will clear after a successful dynamicbattery test. A dynamic battery test is performed every four hours once power has been connected tothe control panel and also every time the system is armed in AWAY Mode, STAY Mode 1 or STAYMode 2.



Date and TimeThe date and time fault will register every time the control panel has been powered down. This faultwill not cause the FAULT indicator on the codepad to illuminate unless an Auto-arming time has beenprogrammed by the installer.

This fault will clear once the date and time has been programmed if an Auto-arming time has beenprogrammed. Refer to “Setting The Date and Time” on page 38 for further information.

Sensor WatchA sensor watch fault will register because one of the detection devices has stopped working or hasfailed to detect movement for the programmed time period whilst the system is disarmed. The faultwill clear after the registered zone has been unsealed and resealed again. Hold down the 5 button asecond time to display the zone that registered the sensor watch fault.

Horn Speaker MonitorA horn speaker fault will register when the horn speaker is disconnected from the control panel. Thisfault will clear when the horn speaker has been reconnected.

Telephone Line FaultA telephone line fault will register when the telephone line connected to the control panel has been cutor disconnected for a continuous period of 40 seconds or more. This fault will clear when thetelephone line has been reconnected for a period of over 40 seconds.

E2 FaultAn E2 fault will register when the control panel detects an internal checksum error.

Codepad Fuse FailA codepad fuse fail fault will register when either the codepad fuse or the accessories fuse has blownor is disconnected. This fault will clear when the blown fuse is replaced or reconnected.

Communication FailureA communication failure fault will register if the control panel was unsuccessful in calling thereceiving party after the control panel has exhausted its maximum number of attempts.

AC Mains FailureAn AC mains failure will flash the MAINS indicator, sound the codepad buzzer once every minute andsend an "AC Fail" report to the monitoring station. This fault will clear once the AC mains has beenreconnected. An "AC Restore" report will be transmitted once the AC mains has been restored formore than two minutes.



Codepad Duress AlarmA codepad duress alarm can be used as a hold up alarm. This will occur when the number 9 is addedto the end of any valid user code that is being used to disarm the system. A duress alarm is alwayssilent and can only be made use of if your system is reporting back to a monitoring station or numericpager.

+ 9 +

There is a feature available that allows the number 3 to be used for a codepad duressalarm instead of the number 9. Contact your installer if you wish the codepad duress alarmto use the number 3 button.

Codepad Panic AlarmA codepad panic alarm will be triggered when either the 1 and 3 buttons or the STAY and AWAYbuttons are pressed simultaneously. This is an audible alarm. Contact your installer if you wishcodepad panic to be silent.

1 + 3 or +

Codepad Fire AlarmA codepad fire alarm will be triggered when the 4 and 6 buttons on the remote codepad are pressedsimultaneously. A distinct fire sound is emitted through the horn speaker to indicate this type of alarmcondition. The fire sound is different to the burglary sound. This is an audible alarm. Contact yourinstaller if you require this to be silent.

4 + 6

Codepad Medical AlarmA codepad medical alarm will be triggered when the 7 and 9 buttons on the codepad are pressedsimultaneously. This is an audible alarm. Contact your installer if you require this to be silent.

7 + 9



Remote Radio Transmitter OperationThe Solution 862 control panel has the ability to be remotely operated using a Hand Held 2Channel Radio Transmitter. The radio transmitter has 4 buttons, each of which can perform variousfunctions such as arming and disarming the system and to operate remote outputs. These are describedbelow in detail.

When using the hand held transmitter to operate the system, audible indications can be providedthrough the horn speakers and visual indications provided by the blue strobe light. This will allow youto operate the system from outside the building with confidence. The feature of audible indicationbeeps and strobe flashes can only be programmed by your installer.

No Of Beeps System Status1 System Disarmed2 System Armed In AWAY Mode

Two tone beep System Armed In STAY Mode

Table 15: Horn Speaker Beeps

Strobe Operation System Status3 Seconds Duration System Disarmed6 Seconds Duration System Armed In AWAY Mode

6 Seconds Duration System Armed In STAY Mode

Table 16: Strobe Indications

Before any of these features will operate, you will need to teach the control panel the transmitter radiocode. Refer to “Error! Reference source not found.” on page 32 for more information.

Arming Via Transmitter In AWAY ModePress button one on the transmitter for two seconds.Two beeps will be heard on the remote codepad and the AWAY indicator will illuminate. Exit time willnow commence.

If the horn speaker indication beeps have been enabled, two beeps will be heard from the horn speaker.If strobe flashes have been enabled, the strobe will operate for six seconds.

Disarming Via Transmitter From AWAY ModePress button one on the transmitter for two seconds.Two beeps will be heard on the remote codepad and the AWAY indicator will extinguish.

If the horn speaker indication beeps have been enabled, one beep will be heard from the horn speaker.If strobe flashes have been enabled, the strobe will operate for three seconds.

Arming Via Transmitter In STAY ModePress button two on the transmitter for two seconds.Two beeps will be heard on the remote codepad and the STAY indicator will now illuminate.

If horn speaker indication beeps have been enabled, a two-tone beep will be heard from the hornspeaker. If strobe flashes have been enabled, the strobe will operate for six seconds.



Disarming Via Transmitter From STAY ModePress button one on the transmitter for two seconds.Two beeps will be heard on the remote codepad and the STAY indicator will extinguish.

If the horn speaker indication beeps have been enabled, one beep will be heard from the horn speaker.If strobe flashes have been enabled, the strobe will operate for three seconds.

Panic Alarm Via TransmitterPress both buttons 1 and 2 together for two seconds on the hand held transmitter. This will cause apanic alarm which will activate the horn speaker, strobe and internal sirens.

Operating Remote Outputs Via TransmitterThere are two remote outputs that can be operated from buttons 3 and 4 on the Hand Held 2 ChannelRadio Transmitter. These outputs can only be programmed by your installer.

Turning Output 1 ‘ON’Press button 3 on the transmitter for two seconds. Output 1 will now turn on.

Turning Output 1 ‘OFF’Press button 3 on the transmitter for two seconds. Output 1 will now turn off.

Turning Output 2 ‘ON’Press button 4 on the transmitter for two seconds. Output 2 will now turn on.

Turning Output 2 ‘OFF’Press button 4 on the transmitter for two seconds. Output 2 will now turn off.



Master Code FunctionsMaster Code functions are designed to allow those users that have the appropriate priority level toperform certain functions of a supervisory level. These functions can only be carried out while thesystem is in the disarmed state.

The default Master Code is 2580 and is known as User 1. It is possible for this system tohave multiple Master Codes. Please check with your installer as to how your system isconfigured.

To enter the required Master Code Function, enter your MASTER CODE followed by the requiredFUNCTION digit and the AWAY button.

+ +

These functions can only be carried out when the system is in the disarmed state.

Function Description0 Arm Or Disarm Both Areas At The Same Time1 Changing Or Deleting User Codes/Remote Radio User Codes2 Changing Domestic Phone Numbers3 Changing Telco Arm/Disarm Sequence4 Setting STAY Mode 2 Zones5 Turning Outputs On/Off6 Setting The Date and Time7 Walk Test Mode8 Event Memory Recall9 Reserved

Table 17: Master Code Functions

Arm Or Disarm Both Areas At The Same TimeThis option allows you to arm or disarm both areas at the same time when the system has beenpartitioned. Both areas will arm or disarm to follow the state of the area that the code was enteredfrom (ie: If you disarm an area, the other area will disarm, or if you arm an area, the other area willarm as well). This allows a user to ensure that both areas will be armed by pressing one extra buttonrather than entering a user code at both area codepads.

How To Arm Or Disarm Both Areas At The Same TimeEnter your MASTER CODE followed by 0 and the AWAY button. Two beeps will be heard and bothareas will arm or disarm.

+ 0 +



Changing and Deleting User CodesThis function allows a Master Code holder to add/change or delete any of the system user codes.

When changing or deleting user codes it is important that you know the number of the user you wish tochange or delete. Your installer should provide you with this information at the time of installation.

To Add Or Change A User Code1. Enter your MASTER CODE followed by 1 and the AWAY button. Three beeps will be

heard and the STAY and AWAY indicators will begin to flash.

2. Enter the user number (1-16) that you wish to add or change followed by the AWAY button.

Two beeps will be heard and the corresponding ZONE indicator will illuminate. Refer to"Table 18: Zone Indicators Showing Relative User Numbers" on page 31.

3. Enter the digits required (from 1-4 digits) for the new code followed by the AWAY button.Two beeps will be heard and the STAY and AWAY indicators will extinguish.

If you wish to change any further user codes, repeat this procedure as many times as required.

+ 1 + + + + +

When adding or changing user codes, this function will automatically terminate if a buttonis not pressed within sixty seconds. Pressing the AWAY button will also terminate thesession at anytime. One long beep indicates the code entered already exists or anincorrect user number has been selected.

To Delete A User Code1. Enter your MASTER CODE followed by 1 and the AWAY button. Three beeps will be


2. Enter the user number (1-16) that you wish to delete followed by the AWAY button.

Two beeps will be heard and the corresponding ZONE indicator will illuminate. Refer to“Table 18: Zone Indicators Showing Relative User Numbers” on page 31 for moreinformation.

3. Press the STAY button to delete the user code. Two beeps will be heard and the STAY andAWAY indicators will extinguish.

If you wish to delete any further user codes, repeat this procedure as many times as required.

+ 1 + + + +

When deleting user codes, this function will automatically terminate if a button is notpressed within sixty seconds. Pressing the AWAY button will also terminate the sessionat anytime. One long beep indicates an incorrect user number has been selected.



UserNo

Zone 1Indicator

Zone 2Indicator

Zone 3Indicator

Zone 4Indicator

Zone 5Indicator

Zone 6Indicator

Zone 7Indicator

Zone 8Indicator

MainsIndicator

1 ü 2 ü 3 ü 4 ü 5 ü 6 ü 7 ü 8 ü 9 ü ü

10 ü 11 ü ü 12 ü ü 13 ü ü 14 ü ü 15 ü ü 16 ü ü

Table 18: Zone Indicators Showing Relative User Numbers



Changing and Deleting Radio Remote User CodesThis function allows a Master Code holder to add/change or delete any of the system radio remote usercodes.

When changing or deleting radio remote user codes it is important that you know the number of theuser you wish to change or delete. Your installer should provide you with this information at the timeof installation.

To Add Or Change A Remote Radio User Code1. Enter your MASTER CODE followed by 1 and the AWAY button. Three beeps will be


2. Enter the user number (9-16) that you wish to add or change followed by the AWAY button.

Two beeps will be heard and the corresponding ZONE indicator will illuminate. Refer to“Table 19: Zone Indicators Showing Relative Remote Radio User Numbers” on page 33.

3. Now press any button on the transmitter.

Two beeps will be heard and the STAY and AWAY indicators will extinguish. The control panel hasnow been taught the code of the hand held radio transmitter.

If you wish to change any further radio remote user codes, repeat this procedure as many times asrequired.

+ 1 + + + +

When adding or changing user codes, this function will automatically terminate if a buttonis not pressed within sixty seconds. Pressing the AWAY button will also terminate thesession at anytime. One long beep indicates the code entered already exists or anincorrect user number has been selected.

To Delete A Radio Remote User Code1. Enter your MASTER CODE followed by 1 and the AWAY button. Three beeps will be


2. Enter the user number (9-16) that you wish to delete followed by the AWAY button.

Two beeps will be heard and the corresponding ZONE indicator will illuminate. Refer to"Table 19: Zone Indicators Showing Relative Remote Radio User Numbers" on page 33.

3. Press the STAY button to delete the user code. Two beeps will be heard and the STAY andAWAY indicators will extinguish.

If you wish to delete any further user codes, repeat this procedure as many times as required.

+ 1 + + + +

When deleting user codes, this function will automatically terminate if a button is notpressed within sixty seconds. Pressing the AWAY button will also terminate the sessionat anytime. One long beep indicates an incorrect user number has been selected.



UserNo

Zone 1Indicator

Zone 2Indicator

Zone 3Indicator

Zone 4Indicator

Zone 5Indicator

Zone 6Indicator

Zone 7Indicator

Zone 8Indicator

MAINSIndicator

9 ü ü 10 ü 11 ü ü 12 ü ü 13 ü ü 14 ü ü 15 ü ü 16 ü ü

Table 19: Zone Indicators Showing Relative Remote Radio User Numbers

User codes 9-16 and Radio user codes 9-16 share the same user numbers. It is thenpossible to have a 4 digit user number and a radio user allocated to the same usernumber.When deleting user numbers 9-16, both the 4 digit user number and the radio user will beerased when deleting the user number selected.

Changing Domestic Phone NumbersThis option allows the Master Code holder to view and program the required telephone numbers thatthe system will call in the event of an alarm. For a more detailed description, refer to "DomesticDialling Reporting" on page 46 for further information.

To Change Domestic Phone NumbersEnter your MASTER CODE followed by 2 and the AWAY button. Three beeps will be heard and theSTAY and AWAY indicators will begin to flash. If there are telephone numbers already programmed,they will be displayed one digit at a time via the zone indicators on the codepad. Refer to "Table 20:Zone Indicators For Changing Phone Numbers" on page 34 for the indicators and their meanings.

If there are no telephone numbers programmed, a further two beeps will be heard after entering thismode. These two beeps are normally heard after the last digit of the last phone number has beendisplayed.

1. Enter all the digits for Phone Number 1, one digit at a time. As each digit is entered, thecorresponding codepad indicators will illuminate.

2. After you have entered all the digits of the first telephone number press the STAY buttonfollowed by the 4 button if there is more than one phone number to be programmed. Thiswill insert a break between the first telephone number and the second telephone number. Ifthere is only one telephone number, press the AWAY button to exit this mode.

3. Enter all the digits for Phone Number 2, one digit at a time. As each digit is entered, thecorresponding codepad indicators will illuminate. After the last digit of the secondtelephone number, press the AWAY button to exit this mode unless a third telephonenumber is required.

+ 2 + + + + 4 + +



The maximum number of digits allowed is 48. This includes any pauses and any breaksthat you have programmed.

The feature of Domestic Dialling must be programmed by your installer. Refer to the“Installation Notes” on page 55 for information on whether your system has beenprogrammed for domestic tone reporting.

To Disable Domestic Dialling1. Enter your MASTER CODE followed by 2 and the AWAY button. Three beeps will be


2. Press the STAY button followed by the 4 button and the AWAY button to disable domesticdialling.

+ 2 + + + 4 +

DigitZone 1

IndicatorZone 2

IndicatorZone 3

IndicatorZone 4

IndicatorZone 5

IndicatorZone 6

IndicatorZone 7

IndicatorZone 8

IndicatorMAINS

Indicator0 ü 1 ü 2 ü 3 ü 4 ü 5 ü 6 ü 7 ü 8 ü 9 ü ü ∗∗ ü ü # ü ü

Pause ü ü Break ü ü

Table 20: Zone Indicators For Changing Phone Numbers

Changing Telco Arm/Disarm SequenceThis feature allows you to automatically divert all incoming phone calls at your home or office toanother phone number of your choice. This feature is only available if your telecommunicationprovider has the call forward option available.

When arming the system in AWAY Mode, the control panel will automatically dial thetelecommunication exchange to redirect all calls to your mobile phone, pocket pager or answeringservice. When activated, your telephone will not ring but outgoing calls may still be made.

When the system is next disarmed, the control panel will automatically dial the telecommunicationexchange to undivert your home or office phone.

Contact your telecommunications provider for more information on call forward operations.



How To Program Telco Arming Sequence - Easy Call Forward (Immediate On)

1. Enter your MASTER CODE followed by 3 and the AWAY button.Three beeps will be heard and the STAY and AWAY indicators will begin to flash.

2. Press button 1 followed by the AWAY button to change the Telco arming sequence. Threebeeps will be heard.

If a previous call forwarding sequence has already been programmed, the sequence will bedisplayed one digit at a time via the remote codepad indicators. Refer to “Table 20: ZoneIndicators For Changing Phone Numbers” on page 34 for the indicators and their meanings.

If there is no call forward sequence programmed, a further two beeps will be heard afterentering this mode. These two beeps are normally heard after the last digit of the callforward sequence has been displayed.

3. Enter STAY + 121 followed by the Phone Number you wish the control panel to divert allcalls to followed by STAY + 2 and the AWAY button. Two beeps will be heard and thesystem will return to the disarmed state.

+ 3 + + 1 + + + 121+ + + 2 +

How To Program The Telco Disarming Sequence – Easy Call Forward (Immediate Off)

1. Enter your MASTER CODE followed by 3 and the AWAY button.Three beeps will be heard and the STAY and AWAY indicators will begin to flash.

2. Press button 2 followed by the AWAY button to change the Telco disarming sequence.Three beeps will be heard.

If a previous Telco disarming sequence has already been programmed, the sequence will bedisplayed one digit at a time via the remote codepad indicators. Refer to “Table 20: ZoneIndicators For Changing Phone Numbers” on page 34 for the indicators and their meanings.

If no Telco disarming sequence has been programmed, a further two beeps will be heardafter entering this mode. These two beeps are normally heard after the last digit of the callforward disarming sequence has been displayed.

3. Enter STAY + 221 + STAY + 2 and the AWAY button.Two beeps will be heard and the system will return to the disarmed state.

+ 3 + + 2 + + + 221+ + 2 +



Setting STAY Mode 2 ZonesThis function allows the master code holder to select which zones are to be automatically isolatedwhen the system is armed in STAY Mode 2.

Every time the system is armed in STAY Mode 2, the zones selected using this function will beautomatically isolated.

To arm the system in STAY Mode 2, hold down the 0 button until two beeps are heard. Refer to“Hold Down Functions" on page 41 or “Arming The System In STAY Mode 2” on page 21 for moreinformation.

How To Set STAY Mode 2 Zones1. Enter your MASTER CODE followed by 4 and the AWAY button.

Three beeps will be heard and the STAY indicator will begin to flash.

2. * Enter the zone number that you wish to automatically isolate followed by the STAYbutton. The corresponding ZONE indicator will now begin to flash to display that you haveselected the zone to be automatically isolated when the system has been armed in STAYMode 2.

If more than one zone is required to be automatically isolated, repeat step 2 until all zonesrequired have been selected.

3. Press the AWAY button to exit this function.Two beeps will be heard and the system will return to the disarmed state. The zones thatwere selected to be automatically isolated in STAY Mode 2 and the STAY indicator willextinguish.

+ 4 + + + +




Turning Outputs On/OffIf an output has been programmed for remote operation, you may turn the remote output on oroff using this Master Code function.

To Turn An Output On From The Remote Codepad1. Enter your MASTER CODE followed by 5 and the AWAY button. Three beeps will be


2. Enter the required Output Number followed by the AWAY button. Three beeps will beheard and the output will now turn on. Repeat step 2 if more than one output is required tobe turned on.

3. Press the AWAY button again to exit this function. Two beeps will be heard and the STAY

and AWAY indicators will extinguish.

+ 5 + + + +

To Turn An Output Off From The Remote Codepad1. Enter your MASTER CODE followed by 5 and the AWAY button. Three beeps will be


2. Enter the required Output Number followed by the STAY button. Two beeps will be heardand the output will now turn off. Repeat step 2 if more than one output is required to beturned off.

3. Press the AWAY button to exit this function. Two beeps will be heard and the STAY andAWAY indicators will extinguish.

+ 5 + + + +



Setting The Date and TimeThis function needs to be used when the date and time needs to be changed or the system hasbeen powered down.

To Set The New Date and Time1. Enter your MASTER CODE followed by 6 and the AWAY button.

Three beeps will be heard and the STAY and AWAY indicators will begin to flash.

2. Enter the day, month, year, hour and minute using the (DD, MM, YY, HH, MM) format.

3. Press the AWAY button when finished to exit this function.Two beeps will be heard and the STAY and AWAY indicators will extinguish.

+ 6 +

ExampleIf the date and time needs to be set for the 1st January 1998 at 10:30 PM, program the date and time asfollows;

+ 6 +

0 + 1 + 0 + 1 + 9 + 8 + 2 + 2 + 3 + 0 +

Walk Test ModeWalk test mode allows you to test the detection devices that are connected to your system toensure that they are functioning correctly. This should be performed on a weekly basis.

Before activating walk test mode, isolate any zones that are not required for testing. Refer to“Zone Isolating Mode" on page 17 for more information on isolating zones.

To Enter Walk Test Mode1. Enter your MASTER CODE followed by 7 and the AWAY button.

Three beeps will be heard and the STAY and AWAY indicators will begin to flash. Thecodepad will beep once every second while the system is in walk test mode.

2. Unseal and seal the zones to be tested. The codepad will sound one long beep and the hornspeaker will sound one short beep every time a zone is sealed or unsealed.

3. Press the AWAY button to exit this function.Two beeps will be heard and the STAY and AWAY indicators will extinguish.

+ 7 +



Event Memory Recall ModeThis feature allows you to playback the last forty events that have occurred to the system. The eventmemory recall mode reports all alarms and arming/disarming of the system in the AWAY Mode andSTAY Mode 1 and 2. This function helps with trouble shooting system faults. The events aredisplayed via the codepad indicators.

To Enter The Event Memory Recall Mode1. Enter your MASTER CODE followed by 8 and the AWAY button. Three beeps will be

heard. The events will be played back via the codepad indicators in reverse chronologicalorder.

+ 8 + Example

If the events were as follows:

Event No Event Description1 System Armed In AWAY Mode2 Alarm In Zone 33 Alarm In Zone 44 System Disarmed

Table 21: Event Memory Recall - Example Events

The event memory playback will report as follows:

Event No Codepad Indicator Event Description4 All Indicators Off Except MAINS System Disarmed3 Zone 4 + AWAY Indicator Illuminates Alarm In Zone 42 Zone 3 + AWAY Indicator Illuminates Alarm In Zone 31 AWAY Indicator Illuminates System Armed In AWAY Mode

Table 22: Event Memory Recall - Example Event Playback

Each event is indicated by a beep and an illuminated indicator. Resetting a 24 hour alarm in thedisarmed state is indicated by one beep only. After the last event, three beeps will be heard to indicatethe end of playback. The replay can be terminated at any time by pressing the AWAY button.

During the event memory playback, arming the system in STAY Mode 1 and STAY Mode 2is indicated by the STAY indicator illuminating. There is no differentiation between armingthe system in STAY Mode 1 and STAY Mode 2.

If the control panel has been powered down, the memory of all events will be lost.



User Code Functions – Partitioned Systems OnlyTo enter the required user code function, enter your user code followed by the required FUNCTIONdigit and the AWAY button.

+ +

Function Description0 Arm Or Disarm Both Areas At The Same Time

Table 23: User Code Functions

Arm Or Disarm Both Areas At The Same TimeThis option allows you to arm or disarm both areas at the same time when the system has beenpartitioned. Both areas will arm or disarm to follow the state of the area that the code was enteredfrom (ie: If you disarm an area, the other area will disarm, or if you arm an area, the other area willarm as well).

This allows a user to ensure that both areas will be armed by pressing one extra button rather thanentering a user code at both area codepads.

To Arm Or Disarm Both Areas1. Enter your user code followed by 0 and the AWAY button. Two beeps will be heard and

both areas will arm or disarm.

+ 0 +



Hold Down FunctionsHold down function have been incorporated to allow easy activation of specific operations. When abutton is held down for two seconds, two beeps will be heard and a particular function will operate.The functions available are listed below.

Arm The System In AWAY ModeHolding the AWAY button down until two beeps are heard will arm the system inAWAY Mode.

If the system has been partitioned, holding down the AWAY button on an area addressable codepadwill only arm the area that the codepad belongs to in AWAY Mode. Holding down the AWAY buttonon a Master Partitioned Codepad will not arm the area that is currently displayed and will toggle to thenext available area.

Arm The System In STAY Mode 1Holding the STAY button down until two beeps are heard will arm the system in STAYMode 1. If there has not been an alarm during the armed cycle, holding the STAYbutton down a second time will disarm the system from STAY Mode 1.

If an alarm has occurred or entry warning has been triggered, a valid user code will need to be used todisarm the system.

If the system has been partitioned, holding down the STAY button until two beeps are heard will onlyarm the area that the codepad belongs to in STAY Mode 1.

Arm The System In STAY Mode 2Holding the 0 button down until two beeps are heard will arm the system in STAY

Mode 2. If there has not been an alarm during the armed cycle, holding the 0 buttondown a second time will disarm the system from STAY Mode 2.

If an alarm has occurred or entry warning has been triggered, a valid user code will need to be used todisarm the system.

If the system has been partitioned, holding down the 0 button will have no effect as STAY Mode 2does not operate when the system has been partitioned.

Horn Speaker TestHolding the 1 button down until two beeps are heard will sound the horn speaker for atwo second burst. No other sounding device will sound in this mode.

If An EDMSAT – Satellite Siren has been connected to the control panel, this function will test thehorn speaker for a two second burst followed by the strobe for two seconds.

Bell TestHolding the 2 button down until two beeps are heard will sound the speakers for a twosecond burst. No other sounding device will sound in this mode.

If an EDMSAT – Satellite Siren has been connected to the control panel, this function will test thehorn speaker for a two second burst followed by the strobe for two seconds.

1

2

0



Strobe TestHolding the 3 button down will operate the strobe. No other device will operate in thismode.

If an EDMSAT – Satellite Siren has been connected to the control panel, this function will also test thestrobe on the satellite siren.

1. Hold down the 3 button until three beeps are heard. The strobe will begin to flash.2. Hold down the 3 button until two beeps are heard. The strobe will stop flashing.

Turning Day Alarm On and OffHolding the 4 button down will turn day alarm on or off.

1. Hold down the 4 button until three beeps are heard. Day alarm has now been turned on.2. Hold down the 4 button until two beeps are heard. Day alarm has now been turned off.

Fault Analysis ModeThere are various system faults that can be detected by the control panel. When any of theseare present, the FAULT indicator will begin to flash and the codepad will beep once everyminute. Refer to "Fault Descriptions" on page 24 for a more detailed description on eachfault type.

1. Hold the 5 button down until two beeps are heard.The STAY and AWAY indicators will begin to flash in unison with the FAULT indicator. Oneor more ZONE indicators (1-8) will illuminate to indicate the type of fault that has occurred.

2. To exit fault analysis mode, press the AWAY button. The STAY and AWAY indicators willextinguish.

Zone Indicator Fault Description1 Low Battery2 Date and Time3 Sensor Watch4 Horn Speaker Disconnected5 Telephone Line Fault6 E2 Fault7 Codepad Fuse Fail8 Communications Failure

Table 24: Fault Indicators

Initiate A Modem CallHolding the 6 button down until two beeps are heard will force the control panel to dial thecallback telephone number programmed in an attempt to connect to the installer’s remotecomputer. Your installer may require you to do this for remote programming changes.

Reset Latching OutputsHolding the 7 button down until two beeps are heard will reset any programmable outputthat has been programmed to remain on once it has been activated. This could be a door bellthat is required to keep ringing until someone has acknowledged it. Your installer willadvise you if this feature has been set.

3

4

5

6

7



Codepad ID and Beeper Tone ChangeHolding down the 8 button for two seconds performs one of two functions.

The first function is to indicate the area that the codepad belongs to. The second function changes thetone of the codepad buzzer. There are fifty different tones to choose from between 1500 Hz and 5000Hz and they are specific to each codepad. In a multiple codepad installation, each codepad can have adifferent tone.

To Determine The Area That The Codepad Belongs ToThis function is only available if the system has been partitioned.

1. Hold the 8 button down until two beeps are heard before releasing the button.

A zone indicator will illuminate to indicate which area that the codepad belongs to.

Zone Indicator Codepad ID1 Area 1 Codepad2 Area 2 Codepad7 Master Partitioned Codepad

Table 25: Codepad ID Descriptions

If no zone indicator illuminates, the codepad cannot be used when the system has been partitioned.

2. Press the AWAY button to exit this function.

To Change The Tone Of The Buzzer1. Hold the 8 button down continuously. The tone of the buzzer will start to increase in pitch.

If the codepad is an addressable area codepad or a Master Partitioned codepad, two beeps will be heardindicating the area that the codepad belongs to as described above. Shortly after the two beeps areheard, the tone of the codepad buzzer will begin to increase in pitch.

2. Release the 8 button when the desired tone has been reached.

3. Press the AWAY button to exit this function.

Initiate A Test ReportHolding the 9 button down until two beeps are heard will send a "Test" report which isused to test the dialling and reporting capabilities of the system without causing the sirensto sound. This hold down function is only applicable if your system has a communicationdialler fitted and enabled.

8

9



PartitioningThe Solution 880 control panel can be partitioned or split into two individual areas. Both areascan be operated from one Master Partitioned codepad or from a number of separate area addressablecodepads. In this case, one of each will be designated to a particular area.

Master Partitioned Codepad IndicatorsThe indicators on a Master Partitioned codepad are configured in to four groups. Following is adescription of what the indicators show.

Zone IndicatorsZone indicators (1-8) display the status of each zone. These zones belong to the area that has the AREADISPLAY indicator illuminated (ie. If a ZONE indicator is illuminated, that zone is unsealed and if theZONE indicator is not illuminated, that zone is sealed).

Area On/Off IndicatorsThe group of four AREA ON/OFF DISPLAY indicators show the status of each area (ie. If an indicator isilluminated, that area is armed and if the indicator is not illuminated, that area is disarmed).

Area Display IndicatorsA group of four AREA DISPLAY indicators show what area the zones belong to that are currently beingdisplayed.

Status IndicatorsA group of four indicators show the following:

AUX IndicatorThe AUX indicator displays when the system is using the telephone line communicating to thereceiving party.

The AUX indicator will flash in conjunction with the PARTIAL indicator to indicate successful entry intoany programming mode. For example, this will occur when using Master Code functions.

Mains IndicatorThis indicator displays the status of the AC mains supply (ie. If the MAINS indicator is illuminated, theAC mains is normal and if the indicator is flashing, the AC mains has been disconnected).

Fault IndicatorThis indicator displays the status of the systems fault register (ie. If the FAULT indicator is flashing, thesystem has detected a fault that has not yet been acknowledged. If the indicator is illuminated, thefault has been acknowledged and if the indicator is not illuminated, the system has no system faults.

Partial IndicatorThe partial indicator displays whether an area is armed in STAY Mode 1 (ie. If the PARTIAL indicatoris illuminated, an area is armed in STAY Mode 1, and if the PARTIAL indicator is not illuminated, noareas are armed in STAY Mode 1). Whilst isolating zones, the PARTIAL indicator flashes to indicatethat you are in the isolate mode. The PARTIAL indicator will flash in conjunction with the AUXindicator to indicate successful entry into any programming mode. For example, this will occur whenusing Master Code functions.



Operating From A Master Partitioned CodepadIf you have a partitioned system with a MasterPartitioned codepad installed, the operating procedureis the same as described throughout this manual withone exception. All operations are relative to the areawhose AREA DISPLAY indicator is illuminated at thetime.

Figure 3: Master Partitioned Codepad

ExampleIf the AREA DISPLAY indicator number 2 is illuminated, all operations performed will effect only Area2. To perform any operations in another area, you will have to move the AREA DISPLAY illuminator tothe desired area.

To Move From One Area To The Next1. Press the AWAY button. The area display indicator will move to the next area.2. Press the AWAY button again. The area display indicator will move to the next area.

Operating From Area Addressable CodepadsIf you have a partitioned system with Area Addressable codepads, the operating procedure is exactlythe same as described throughout this manual. Refer to “Codepad ID and Beeper Tone Change” onpage 43 to determine which area a particular codepad belongs to.

Communication OptionsYour Solution 880 control panel has a communications dialler fitted to report all alarms andsystem events. These events can be reported to a number of destinations via different transmissionformats. These different formats have varying levels of ability. Some can report all events whileothers have limitations and may report alarms only. The suitability of the different formats should bediscussed with your installer.

Options and AccessoriesDomestic Tone Only ReportingBack To Base Reporting Via Digital CommunicatorBasic Pager ReportingPhone Controller



Remote Arming Via The TelephoneThis feature allows you to arm your system from any remote location via the telephone line. Forobvious security reasons, the system cannot be disarmed using this method. To make use of thisfeature, you will require a touch tone telephone or the phone controller.

To Remotely Arm Your System Via The Telephone1. Call the telephone number that your control panel has been connected to.

2. When the control panel answers the incoming call, a short jingle will be heard. Hold thephone controller to the mouth piece of the telephone and press the button on the side of theunit for 3 seconds. You can alternatively press the * button on the touch tone telephone for3 seconds to arm the system.

If you hear a number of strange sounding tones when the control panel answers theincoming call, this means that the system has been programmed for remote programmingfunctions. Simply wait for a pause in the tones and follow step 2 to remotely arm thesystem.

3. After releasing the button on the phone controller or the * button on the touch tonetelephone, two beeps will be heard to indicate that the system has armed in AWAY Mode.

4. Hang up the telephone and the system will remain armed.

If the control panel does not answer the call, this means that the system may already be armed, remotefunctions have not been enabled or the ring count has been set to zero so that the control panel does notanswer any incoming calls.

Where both remote arming and Upload/Download via the installer’s remote computer havebeen selected, the control panel will answer the call expecting the remote computer. Thisis easily noticed as the modem negotiating tones will be heard rather than the remotearming jingle.

If your system has been partitioned, when you remote arm the system, both areas will armin AWAY mode.

Domestic Dialling ReportingWhen the control panel has activated into an alarm condition, it will commence dialling the firstprogrammed telephone number. If a busy or engaged tone has been detected, the control panel willhang up and commence dialling the second telephone number (if one is programmed). The first callhowever will be counted as one unsuccessful dialling attempt. If the second telephone number is alsobusy or an engaged tone is detected, the control panel will hang up and commence dialling the thirdtelephone number (if one is programmed).

If a busy tone is not detected, the control panel will assume that the phone has been answered and willbegin sending its transmission. The transmission consists of a siren tone followed by a unitidentification beep. The identification beep will allow the customer to verify which control panelmade the call if more than one control panel is reporting to the same telephone number.

After the identification beep, a long pause will follow allowing you to acknowledge the call. If the callis not acknowledged during the pause, the sequence of the siren tone, the identification beep and thepause will continue until you acknowledge the call or until the control panel hangs up after twominutes has expired.



A maximum of 6 calls per alarm event will be made when the control panel has been set upfor domestic dialling format. This count includes any unsuccessful calls. The counter willreset if the zone retriggers and a further 6 attempts will be made. The control panel willstop dialling after 6 attempts or 3 successful calls. The control panel will also stop diallingif a valid user code has been entered at the remote codepad.

To Acknowledge Domestic DiallingOnce the call has been received, if it is not acknowledged by pressing the * button on a touch tonetelephone or by using the phone controller, the control panel will continue to send its transmission fora period of 2 minutes. It will then hang up and commence dialling the next telephone number. If thecall is acknowledged, the control panel will hang up and no further calls will be made for that event.

Basic Pager ReportingBasic pager reporting has been introduced so that alarms and system information can be transmitted toa pocket pager allowing you to receive information from your alarm system at any time.

Basic pager format requires some interpretation of the numbers that appear on the display, however, itis possible to differentiate between 1000 different control panels when a number of control panels arereporting to the one pager.

Figure 4: Basic Pager Display

The example shows that the transmission has come from Subscriber ID Number 678 and that zone 2 isin alarm, zone 3 has been manually isolated, the system is armed, the panic zone is normal, the AC isconnected and there is no fault condition.



Optional EquipmentThere are numerous accessories and features that can be added to your alarm system. Contact yourinstaller for more information on any of the accessories listed below.

EDMSAT - Satellite SirenTo enhance the security of your system a satellite siren is available. When tampered with ordisconnected from your system it will still continue to emit its ear shattering warning sound.

Additional CodepadsNumerous codepads can be fitted giving you the ability to control your system from not only the entrypoint but even from your bedroom or anywhere else that you may require.

Night Arm StationThe night arm station is a touch pad that allows you to perform three basic functions. Firstly, it allowsyou to arm your alarm system in STAY Mode by pressing just one button. Secondly, it allows you toactivate a panic alarm 24 hours a day should an emergency situation arise. Thirdly, it provides systemstatus at all times via its indicator lights. Using a night arm station means that at the press of a buttonyou can arm your entire alarm system except for the zones that are designated for STAY Mode. Thenight arm station will allow the user to disarm the system from STAY Mode, providing that no alarmhas been triggered.

Radio Remote ControlThis equipment when fitted will enable you to control the general operation of your system from aportable hand held transmitter. It can even be used for basic arm/disarm where there is a requirementfor a keyswitch.

Phone ControllerThe phone controller can be used for remote arming of your system. Where this feature is required thephone controller can be used to generate a specific tone that will arm your system via the telephone.The phone controller can also be used to acknowledge domestic dialling.

Hand Held Radio Remote Control Panic ButtonAny number of hand held panic buttons can be connected to your system. These are ideal for medicalor emergency situations where help is required instantly. The benefits of these are only apparent ifyour system is monitored.

Smoke DetectorsAny number of smoke detectors may be connected to your system for an early warning of a fire. Adifferent sound is available for your horn speaker if a smoke detector is triggered. This different soundwill alert your neighbours to a fire rather than a burglary.

Photoelectric BeamsPhotoelectric beams can be connected to your system to provide perimeter protection. These beamscan be placed up to distances of 160 metres apart. Any movement across the beams (ie. a person orvehicle entering a driveway) will cause an alarm. These can be used in both indoor and outdoorapplications.



Passive Infrared DetectorsPassive infrared (PIR) detectors are the most common type of detection devices used. PIR's detecthuman body heat up to a distance of approximately 15 metres.

Magnetic Reed SwitchesReed switches are used to monitor the opening and closing of doors and windows. These are ideal forperimeter protection when used in conjunction with STAY Mode.

Glass Break DetectorsGlass break detectors are used to pick up the sound of breaking glass. These are ideal for shop frontwindows.

Vibration DetectorsVibration detectors are designed to pick up the vibrations of a rattling door or window.

Communications DiallerA communications dialler is fitted to your system to inform another party that an alarm has occurred.Refer to “Communication Options” on page 45 for more information.

Telephone Line Fault MonitorA telephone line fault monitor is designed to connect your alarm system to two telephone lines. Whenline A is disconnected the unit will automatically switch to line B. For added security, line B could beconnected to a stand-alone cellular unit.



Glossary Of TermsTerm Description

Alarm Condition Is when your alarm system is armed and one of the detection devices are violated.A 24 hour zone (eg. Smoke detector) may trigger when armed or disarmed.

Answering MachineBypass

Answering machine bypass has been incorporated so that it is possible to make aconnection with the control panel for remote arming or remote programmingoperations when there is a answering machine or facsimile machine on the sametelephone line.

Armed(System ON)

When the system is in a state ready to accept alarms.

This is the button on your codepad used to execute any given command.

AWAY Mode Is the mode used to arm your system when you leave your premises.

Codepad The codepad allows you to perform all functions such as arming, disarming andprogramming of your alarm system.

Day Alarm Day alarm allows a combination of zones to be monitored while the system is inthe disarmed state.

Detectors Are devices connected to your alarm system used to cause an alarm condition.Some common forms of detection devices are; passive infrared, smoke, photoelectric beams, reed switches and vibration sensors.

Dialler Is a device that is used for communicating to a monitoring station, mobile phoneor pocket pager etc.

Disarmed Is when your system is in a state that will not accept alarms except for 24 hourzones.

Dynamic BatteryTesting

Is a feature used to monitor and test the condition of your backup battery.

EDMSAT(Satellite Siren)

Is a self contained siren unit complete with flashing blue strobe light and a backupbattery. It offers a higher level of security for your alarm system.

Entry Time orEntry Delay

Is the time allowed after entering your premises, to disarm your system before analarm occurs.

Entry Warning Is the beeping from your codepad during entry time to remind you to disarm yoursystem.

Exit Time orExit Delay

Is the amount of time you have to leave your premises after arming your system.

External Equipment Is any device connected to your system such as detectors, codepads and sirens.

Forced Arming Is a situation where your alarm system is permitted to be armed when one or morezones are unsealed.

Handover Delay When your system is armed and zone one is violated, the entry delay starts timing.If zone two is then violated the entry delay time is handed over to zone two and soon through zones three and four. This is known as sequential hand over delay.



Hand Held RadioRemote Control

Can be used to arm and disarm your system or cause a panic alarm.

Lockout Dialler Lockout dialler means that the dialler will only activate once per zone per armingcycle.

Lockout Siren Lockout siren means that the sirens will only activate once per zone per armingcycle.

Master Code Is a numerical code used for arming and disarming the system as well as allowingaccess to all functions that are programmable through the codepad.

Monitoring Station Is a secure location where a digital receiver monitors numerous alarm systems anddeciphers their alarm transmission reports so that the operator can advise theappropriate authorities to take immediate action.

Panic This is a type of alarm raised by you to indicate to the monitoring station thatthere is an emergency situation at your premises.

Phone Controller Is a device used for arming your system via the telephone line. It is also used toacknowledge domestic alarm reports.

Sealed Refers to a zones status. If a zone is sealed, the detection devices are not violatedand the zone indicator will be extinguished (ie. a reed switch is closed or adetector is on stand by waiting for an intrusion).

Sensor Watch Sensor watch gives the control panel the ability to recognise that detection devicesmay have stopped working. This is a feature that monitors the operation of a zoneover a programmed time period.

Silent Alarm When programming your system, it is possible to have an individual zone forsilent alarm. This means that when the zone is violated your alarm system willcommunicate with the monitoring station without sounding the sirens. This canonly be programmed by your installer.

STAY Mode 1 Is a condition that automatically isolates certain zones when your system is armedin STAY Mode 1. These zones can only be programmed by your installer.

STAY Mode 2 Is a condition that automatically isolates certain zones when your system is armedin STAY Mode 2. These zones can only be programmed by a master code holder.

Unsealed Refers to zone status. If a zone is unsealed, the detection devices are violated andthe zone indicator will be illuminated (ie. a reed switch is open or a detector hasnoted an intrusion).

User Code A numerical code used to arm and disarm the system.

Zones A monitored input used to trigger an alarm condition.

24 Hour Zone A monitored input where tamper switches and emergency switches may beconnected. If at any time, (whether your system is armed or disarmed) one ofthese switches is violated, an alarm condition will be generated.



WarrantyElectronics Design and Manufacturing Pty limited warrants this product to be free from defects inmaterial and workmanship for a period of three years from the date of manufacture as indicated by thedate stamp and / or the serial number on the product.

Defective units returned by the purchaser at their own expense during this period will be repaired orreplaced at the option of the manufacturer. The repair or replacement will be free of charge providedthat the defects were not incurred during shipping or handling, or the damage was not due to causesbeyond the control of Electronics Design and Manufacturing Pty Limited, excessive voltage,mechanical shock or damage arising out of abuse, alteration or improper application of the equipment.

Should a product be returned for repair and it is out of warranty, normal repair charges will beapplicable. If the product is unrepairable or deemed uneconomical to repair in EDM’s opinion,another replacement unit will be made available for purchase. In the event of a product beingsuperseded, a similar or equivalent product may be offered for purchase.

LimitationsWhile this system is an advanced design security system, it does not offer guaranteed protectionagainst burglary, fire or any other emergency. An alarm system, whether commercial or residential, issubject to compromise or failure.

Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering,electrical or communications disruption, it is possible for the system to fail to perform as expected.Electronics Design and Manufacturing Pty Limited does not represent that the product or system maynot be compromised or circumvented; or that the product or system will prevent any personal injury orproperty loss by burglary, robbery, fire or otherwise; nor that the product or system will in all casesprovide adequate warning or protection. A properly installed and maintained alarm system may onlyreduce risk of burglary, robbery, fire or otherwise but it is not insurance or a guarantee that theseevents will not occur.

CONSEQUENTLY, ELECTRONICS DESIGN AND MANUFACTURING PTY LIMITED SHALLHAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHERLOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.

Electronics Design and Manufacturing Pty Limited is not an insurer of either the property or safety ofthe user's family or employees and limits its liability for any loss or damage including incidental orconsequential damages to Electronics Design and Manufacturing Pty Limited's original selling price ofthe product regardless of the cause of such loss or damage.

MaintenanceElectronics Design and Manufacturing Pty Limited recommend the system be checked on a weeklybasis for correct operation. Reference should also be made to Australian Standard 2201.1 in thatroutine maintenance should be carried out every six months by a licensed alarm technician.

Year 2000 ComplianceThis notice is to confirm that the Solution 880 control panel is not susceptible to, or will becorrupted by the “Year 2000 Millenium Bug”.

To date, all Solution products that incorporate time keeping facilities employ a rotating 100 yearcalendar. This means that Solution products do not use the century in any time keeping algorithms,only the year within the century.



SpecificationsTemperature Range: 0 – 45 Degrees Celsius

Humidity: 10% - 95%

Power Source: TF008 Plug Pack – 240 Volt / 18 Volt AC @ 1.3 Amp

Stand-By Current: 65 mA

Current Draw In Alarm Condition: 115 mA

Current Draw With No Alarm and Codepad Fitted: 105 mA

Back-Up Battery: 6.5 Ah / 12 Volt DC Rechargeable Sealed Lead AcidBattery

Dimensions: 306 mm x 262 mm x 84 mm (Packed In Carton)

Weight: 2.5 Kg

Austel Approval Number: A96/03/0096 – Only With TF008 Plug Pack

New Zealand Telepermit: PTC 211/96/007

Quality PolicyAS 3901 Clause 4.1.1 Refer to Procedure No 1The operations of Electronics Design and Manufacturing Pty Limited include design, development andmanufacturing of electronic equipment.

Electronics Design and Manufacturing Pty Limited recognises that it is the responsibility of suppliersand contractors to meet their contractual obligations and carry out works which comply fully with therelevant specifications, drawings and contract documents.

It further recognises that the diligent operation of a Quality Management System leads to efficient andeffective execution of the works with a minimum of errors and rework.

Electronics Design and Manufacturing Pty Limited and its Employees are committed to theimplementation of this Quality Management System in accordance with Australian standard AS3901-1987, European standard ISO9001-1987 and New Zealand standard NZS9001-1990 implementingquality systems for design, development and production to the mutual benefit of the customers andElectronics Design and Manufacturing Pty Limited.

Meinrad FormosaManaging Director



Advice To UsersThe Austel permit that has been issued for this product is subject to the following conditions.

• The Solution 880 control panel may only be powered by an EDM Plug Pack TF008(Approval number Q92128).

New Zealand Telepermit NotesThe following notes are only relevant when this product is used in New Zealand.

• The grant of a Telepermit for a device in no way indicates Telecom's acceptance of responsibilityfor the correct operation of that device under all operating conditions.

• The equipment shall not be used in any manner, which could constitute a nuisance to otherTelecom customers.

• Immediately disconnect this equipment should it become physically damaged, and arrange for itsdisposal or repair.

• The transmit level from this device is set at a fixed level and because of this there may becircumstances where the performance is less than optimal. Before reporting such occurrences asfaults, please check the line using a standard Telepermitted telephone and do not report a faultunless the telephone performance is impaired.

• This device is equipped with pulse dialling while the Telecom standard is DTMF tone dialling.There is no guarantee that Telecom lines will always continue to support pulse dialling.

Use of dialling, when this equipment is connected to the same line as other equipment, may giverise to bell tinkle or noise and may also cause a false answer condition. Should such problemsoccur, the user should NOT contact the Telecom Faults Service.

• This equipment is set up to carry out test calls at pre-determined times. Such test calls willinterrupt any other calls that may be set up on the line at the same time. The timing set for suchtest calls should be discussed with the installer.

The timing set for test calls from this equipment may be subject to drift. If this proves to beinconvenient and your calls are interrupted, then the problem of timing should be discussed withthe equipment installer. The matter should NOT be reported as a fault to Telecom FaultsService.

• This equipment shall not be set up to make automatic calls to the Telecom 111 EmergencyService. This equipment should not be used under any circumstances which may constitute anuisance to other Telecom customers.

• In the event of any problem with this device, the systems battery, AC mains supply andtelephone line should be disconnected. The user is to then arrange with the supplier of thedevice to make the necessary repairs.

Should the matter be reported to Telecom as a wiring fault and the fault be proven to be due to thisproduct, a call-out charge will be incurred.



Installation Notes

Installation Company

Technician

Phone Number

Installation Date

Warranty Expires

Panel Software Version

Zone Descriptions

STAYMode

DayAlarm

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8



Entry and Exit Times

Entry Timer 1 Seconds

Entry Timer 2 Seconds

Exit Time Seconds

Entry Guard Time For STAY Mode 1 and STAY Mode 2 Seconds

User Code Options

Code Retry Count Attempts

Codepad Lockout Time Minutes

Arming Options

Forced Arming YES NO

Single Button Arming YES NO

Single Button Disarming YES NO

Remote Arming Via The Telephone YES NO

Automatic Arming YES NO Am/Pm

Automatic Disarming YES NO Am/Pm

Output Options

Output 1

Output 2

Output 3

Output 4



Isolating Options

Standard Isolating YES NO

Code To Isolate YES NO

Communication Options

Domestic Tone Reporting YES NO

Domestic Tone Reporting – Number Of Beeps

Others

Siren Run Time Minutes

Sensor Watch Time Days

Can Your System Be Serviced By Another Technician YES NO

If YES, Installer’s Code

Service Notes



Index

2

24 Hour Zone .............................................................51

A

AC Mains Failure.......................................................25Acknowledge Domestic Dialling ................................47Adding Radio Remote User Codes..............................32Adding User Codes .............................................. 30, 35Advice To Users.........................................................54Alarm Condition ........................................................50Alarm Memory.............................................................9Answering Machine Bypass........................................50Area Display Indicators ..............................................44Area On/Off Indicators...............................................44Arm In AWAY Mode.................................................19Arm In STAY Mode............................................. 20, 41Arm/Disarm Both Areas At Same Time................ 29, 40Armed........................................................................50Arming in STAY mode ................................................21Arming Via Telephone ...............................................46Audible Indicators................................................ 15, 18AUX Indicator ...........................................................44AWAY Indicator.................................................. 14, 16AWAY Mode.............................................................50AWAY or # ...............................................................50

B

Basic Pager Reporting ................................................47Basic System Operation................................................8Battery Testing...........................................................50Bell Test ....................................................................41

C

Changing Domestic Phone Numbers...........................33Changing Radio Remote User Codes ..........................32Changing User Codes ........................................... 30, 35Code Retries.................................................................9Code To Isolate ..........................................................23Codepad.....................................................................50Codepad Beeper Tone Change....................................43Codepad Duress .........................................................26Codepad Extinguish Mode............................................9Codepad Fire..............................................................26Codepad Functions.....................................................22Codepad Lockout Time ................................................9Codepad Medical .......................................................26Codepad Panic ...........................................................26Codepads ...................................................................48Communcation Dialler ...............................................49Communication Failure ..............................................25Communication Options.............................................45CP5 Codepad .............................................................14CP5 LCD Codepad.....................................................16

D

Date and Time................................................ 11, 25, 38Day Alarm ..................................................... 10, 42, 50Day Alarm Latching...................................................10Day Alarm Operation .................................................10Day Alarm Resetting ..................................................10Deleting Radio Remote User Codes ............................32Detectors....................................................................50

Dialler.................................................................. 49, 50Disarm From AWAY Mode........................................19Disarm From STAY Mode..........................................21Disarmed....................................................................50Domestic Dialling - Acknowledge ..............................47Domestic Dialling Reporting ......................................46Domestic Phone Numbers...........................................33Duress Alarm .............................................................26

E

E2 Fault .....................................................................25EDMSAT...................................................................50EDMSAT - Satellite Siren ..........................................48Entry Time ........................................................... 11, 50Entry Warning............................................................50Event Memory Recall .................................................39Exit Time ............................................................. 11, 50External Equipment ....................................................50

F

FAULT - AC Mains Failure........................................25FAULT - Communication Failure ...............................25FAULT - Date and Time.............................................25FAULT - E2 Fault ......................................................25FAULT - Horn Speaker ..............................................25FAULT - Low Battery ................................................24FAULT - Sensor Watch..............................................25Fault Analysis Mode............................................. 24, 42FAULT Indicator............................................ 15, 17, 44Features........................................................................7Fire Alarm..................................................................26Forced Arming ............................................... 19, 20, 50

G

Glass Break Detectors.................................................49

H

Hand Held Radio Remote Control...............................51Hand Held Radio Remote Control Panic .....................48Handover Delay..........................................................50Hold Down Function - Arm In AWAY Mode..............41Hold Down Function - Arm In STAY Mode ...............41Hold Down Function - Bell Test .................................41Hold Down Function - Codepad ID & Beeper Tone

Change ..................................................................43Hold Down Function - Fault Analysis Mode ...............42Hold Down Function - Horn Speaker Test...................41Hold Down Function - Initiate Modem Call ................42Hold Down Function - Initiate Test Report..................43Hold Down Function - Reset Latching Outputs ...........42Hold Down Function - Strobe Test..............................42Hold Down Function - Turn Day Alarm On/Off ..........42Hold Down Functions.................................................41Horn Speaker .............................................................25Horn Speaker Test ......................................................41

I

Initiate Modem Call....................................................42Initiate Test Report .....................................................43Installation Notes........................................................55Introduction..................................................................7Isolating Zones ...........................................................23



L

Latching Outputs ....................................................... 42Lockout Dialler.......................................................... 51Lockout Siren ............................................................ 51Low Battery............................................................... 24

M

Magnetic Reed Switches ............................................ 49MAINS Indicator ............................................15, 17, 44Master Code .............................................................. 51Master Code Function - Arm/Disarm Both Areas At

Same Time ............................................................ 29Master Code Function - Changing & Deleting Codes.. 30Master Code Function - Changing & Deleting Radio

Remote User Codes ............................................... 32Master Code Function - Changing Domestic Phone

Numbers ............................................................... 33Master Code Function - Event Memory Recall ........... 39Master Code Function - Set Date and Time................. 38Master Code Function - Set STAY Mode 2 Zones ...... 36Master Code Function - Turning Outputs On/Off........ 37Master Code Function - Walk Test Mode ................... 38Master Code Functions .............................................. 29Master Partitioned Codepad Indicators ....................... 44Modem Call............................................................... 42Monitoring Station..................................................... 51

N

New Zealand Telepermit Notes .................................. 54Night Arm Station...................................................... 48

O

OFF Indicator/Zone Sealed ........................................ 18ON Indicator/Zone In Alarm ...................................... 18Operating From A Master Partitioned Codepad .......... 45Operating From Area Addressable Codepads.............. 45Operating Remote Outputs Via Transmitter ................ 28Optional Equipment ................................................... 48Outputs - On/Off........................................................ 37

P

Panic ......................................................................... 51Panic Alarm............................................................... 26PARTIAL Indicator ................................................... 44Partitioning................................................................ 44Passive Infrared Detectors.......................................... 49Phone Controller...................................................48, 51Photoelectric Beams................................................... 48Programming Mode ................................................... 17

Q

Quality Policy ............................................................ 53

R

Radio Remote Control................................................ 48Remote Arming Via Telephone .................................. 46Remote Radio Transmitter Operation.......................... 27Reset Latching Outputs .............................................. 42

S

Satellite Siren....................................................... 48, 50Sealed ........................................................................ 51Sensor Watch....................................................... 25, 51Sensor Watch Time .................................................... 10Service Notes ............................................................. 57Silent Alarm............................................................... 51Smoke Detectors ........................................................ 48Standard Isolating ...................................................... 23Status Indicators......................................................... 44STAY Indicator ................................................... 14, 16STAY Mode .............................................................. 51STAY Mode 2 Zones ................................................. 36Strobe Test................................................................. 42System Disarmed ....................................................... 17System Indicators & Operations ................................. 14System Operation......................................................... 8System Operations ..................................................... 19

T

Teaching Remote Radio User Codes........................... 12Telco Arm/Disarm Sequence...................................... 34Telephone Line Fault Monitor .................................... 49Test Report ................................................................ 43Turn Day Alarm On/Off ............................................. 42Turning Outputs On/Off ............................................. 37

U

Unsealed .................................................................... 51User Code .................................................................. 51User Code Function - Arm/Disarm Both Areas At Same

Time...................................................................... 40User Code Priority...................................................... 12User Codes................................................................. 11User Codes 1 - 8......................................................... 11

V

Vibration Detectors .................................................... 49

W

Walk Test Mode......................................................... 38Warranty.................................................................... 52

Z

Zone Indicators ...............................................14, 16, 44Zone Isolating Mode Indicator.................................... 17Zones......................................................................... 51



Date post:	03-Jul-2018
Category:	Documents
Upload:	dinhhanh
View:	217 times
Download:	2 times

Solution 880 Operators Manual - Security Strategies Solution 880 user guide.pdf · Introduction...

Documents