Solutions for Extrusion and Converting Drives and Servo...

Solutions for Extrusion and Converting Drives and Servo Systems

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 392

Your partner for eXtruSIon anD ConVertInG applICatIonS

SSD Parvex has been involved in the design and manufacture of electrical motors and drives since its creation in 1948. Years after years, SSD Parvex has managed to keep its know-how at the cutting edge of technology, building one of the most extended offer in the marketplace, including AC, DC, servo and torque motors and drives solutions. Fully owned company of Parker Hannifin Corporation since 2005, SSD Parvex has gained a worldwide recognition, as a major specialist in electrical motion control technologies.

A GLOBAL APPROACH The compagny has developed its organization and know-how in order to propose only the best technico-economic solutions, that perfectly fit customers needs.

This is made possible because SSD Parvex adopts a global approach, supported by :• a sales network capable of understanding Machine Builders and End-users specific needs• a highly qualified technical staff offering all the assistance needed throughout the specification and integration stages• a flexible industrial organization

As a servosystem specialist, SSD Parvex can carry out any necessary adaptations, based on the standard offer, would it be :• Mechanical adaptations : shaft, flange, Nema flange, housing, ...• Electrical adaptations : speed, speed/torque, voltage, winding, ...• Specific sensor mounting : Endat, Hiperface, incremental encoder, absolute encoder, hall effect sensor, ...• Motor accessories mounting like gearboxes, cables, connectors, ...

When even more flexibility is required, for demanding applications, SSD Parvex can also propose truly « tailored » solutions based on frameless servomotor technologies, resulting in cost, space, stiffness and reliability constraints being handled with maximum care.

thorouGh buSIneSS knowleDGeExtrusion and Converting industries have been part of SSD Parvex core business activities for more than 30 years. Result of close cooperations and long term commitments to various major machine-builders and end-users in Plastics, Rubber, Pulp, Paper and other industries involving extrusion and converting processes, SSD Parvex has acquired thorough business knowledge.More than just products, SSD Parvex has developped a broad range of focused solutions, integrating dedicated features and functionalities that perfectly meet extrusion and converting industries specific needs. Whether they need energy efficient and maintenance free direct drive solutions for extruders, whether they need high precision and dynamic performances servosystems for fly cutting applications, or whether they need compact and cost effective solutions for winders, customers will find the appropriate answer in SSD Parvex offer.

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 3

eXtruSIon anD ConVertInG

p. 22

p. 16

p. 24

p. 26

p. 30

Torque Moors for Extrudersup to 22 100 n.mtMw Series

• Compact direct drive solution• High efficiency• No maintenance• No gearbox• Thrust bearing• Dedicated drive : AC890 with specific algorithms and association table

ATEX Servo Motors1,75 to 35 n.meX Series

• »d» flameproof according to ATEX 94/9/CE directive• Brushless technology• Integrated thermal protection• Brake option

AC Servo Drives1 to 30 a637f / 638 Series

• Ultra fast control loops• Multi-axes synchronization• Electronic Cams• EN954-1 Cat.3 Safety Option• Standard Fieldbuses• 230 or 400Vac Power Supply

Compact Induction Motors 0,75 to 315 kwMa Series

• Compact square shape• High maximal speed• High overload capabilities• Thermal probe• Incremental encoder

Standard Induction Motors0,75 to 315 kwMe-MY Series

• Cost effective solution• Thermal probe• Encapsulated Encoder• Forced Ventilation

BRUSHLESS Servo Motors0,45 to 64 n.mnX Series

• High torque density• Low inertia• Exceptional movement quality• Robust and compact construction

up to 9 000 rpm

p. 4

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 394

Torque MoTors

TMW series 1 200 to 22 100 n.m

DeSCrIptIonThe torque motor is a permanent magnets brush-less motor, optimized to operate at low speeds. It is particularly suitable for direct drive applications requiring high torque capabilities at low speeds. Torque motor can replace favourably asynchro-nous or direct current motors with gearbox. The obtained system is more compact, less noisy and does not require any maintenance.

This system offers many advantages:. no more gearbox. no more maintenance: all the maintenance which comes along with the gearbox disappears: draining, joints replacement... Furthermore, as it is based on a brushless technology, the torque motor does not require any maintenance.. better speed regulation: as a servosystem, the torque motor offers exceptional dynamic perfor-mances, resulting in a more accurate speed regu-lation and a better extrusion quality.. Increased compactness . Silent operation. energy savings

NO mORe GeARBOx NO mAiNteNANCe eNeRGy SAviNGS SiLeNt OPeRAtiON (euROPeAN DiReCtive 2003/20/Ce)BetteR SPeeD ReGuLAtiON iNCReASeD COmPACtNeSS

teChnICal SpeCIfICatIonS

• Torque range 1200 – 22100 N.m (water-cooling)

• Shaft heights 200, 315 or 400 mm

• Rated Voltage 400 VAC and 480 VAC

• Speed 50 – 500 rpm (size dependent)- Field weakening operation up to 1.2xnrated

- Other speeds available on request

• Cooling Water Jacket as standard- Natural ventilation with derating (consult us)

• Mounting IMB3

• Protection degree IP 54

• Thermal protection 1 x KTY sensor and 2 x PTC probes

- Temperature alarm and default

• Shaft end Hollow shaft with keyway as standard- Customized interfaces available on request

• Thrust bearing SKF 294__E as standard

• Feedback sensor

Endat Encoder as standard- High Precision Endat encoder (option)- Resolver (option)

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 5

tMw Series - 400 VaC power Supply(1)

Model pn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow

rate

(l/min)

Drive reference

50 - 75 rpm

TMW305LU 29 70 3940 68 80 5880 4,40 17 AC890SD/4/0073E

TMW306LV 38 75 4830 86 85 7200 4,55 20 AC890SD/4/0087E

TMW406LV 81 75 10300 169 90 15300 16,20 28 AC890SD/4/0180F

TMW408LW 90 60 14200 197 75 21000 19,40 37 AC890SD/4/0216G

TMW40ALW 95 50 18200 219 60 26800 25,10 47 AC890SD/4/0250G

TMW40CLW 116 50 22100 271 60 32500 25,90 56 AC890SD/4/0316G

TMW40CLS 161 70 22000 348 85 32500 25,90 56 AC890SD/4/0420H

75 - 100 rpm

TMW304LR 32 100 3040 70 115 4550 3,45 14 AC890SD/4/0073E

TMW305LT 39 95 3930 84 115 5880 4,40 17 AC890SD/4/0087E

TMW308LU 59 85 6620 133 105 9870 6,50 27 AC890SD/4/0145F

TMW30ALU 71 80 8430 163 95 12500 6,80 34 AC890SD/4/0180F

TMW30ALS 88 100 8410 191 125 12500 6,80 34 AC890SD/4/0216G

TMW406LS 108 100 10300 216 125 15300 16,20 28 AC890SD/4/0250G

TMW408LS 126 85 14200 261 105 21000 19,40 38 AC890SD/4/0316G

TMW408LP 148 100 14100 306 120 21000 19,40 38 AC890SD/4/0361G

TMW40ALQ 151 80 18100 313 100 26800 25,10 47 AC890SD/4/0361G

TMW40CLK 207 90 21900 428 110 32500 25,90 57 AC890SD/4/0520H

100 - 125 rpm

TMW204LU 15 120 1220 35 140 1810 0,75 9 AC890SD/5/0045D

TMW205LT 21 125 1570 47 155 2320 0,78 11 AC890SD/5/0059D

TMW208LU 30 110 2640 71 125 3910 1,03 18 AC890SD/4/073E

TMW304LQ 40 125 3030 81 150 4550 3,45 14 AC890SD/4/0087E

TMW306LS 53 105 4810 115 130 7200 4,55 21 AC890SD/4/0105F

TMW306LR 63 125 4800 129 155 7200 4,55 21 AC890SD/4/0145F

TMW308LQ 79 115 6590 167 140 9870 6,50 28 AC890SD/4/0180F

TMW30ALQ 105 120 8380 216 150 12500 6,80 34 AC890SD/4/0250G

TMW406LP 134 125 10200 266 155 15300 16,20 29 AC890SD/4/0316G

TMW40ALM 198 105 18000 398 130 26800 25,10 47 AC890SD/4/0480H

TMW40ALK 225 120 17900 446 150 26800 25,10 48 AC890SD/4/0590J

TMW40CLI 274 120 21800 536 150 32500 25,90 57 AC890SD/4/0685K

(2) This reference corresponds to the optimum drive for operation at nominal point. May be adapted regarding the application requirements

(1) Other speeds available, consult us.

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 396


tMw Series - 400 VaC power Supply (1)

Model pn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow

rate

(l/min)

Drive reference (2)

125 - 150 rpm

TMW207LS 31 130 2280 70 160 3380 1,00 15 AC890SD/4/073E

TMW208LT 39 140 2630 86 175 3910 1,03 18 AC890SD/4/0087E

TMW305LP 59 145 3900 118 180 5880 4,40 17 AC890SD/4/0105F

TMW308LN 100 145 6560 198 180 9870 6,50 28 AC890SD/4/0216G

TMW406LJ 160 150 10200 306 180 15300 16,20 29 AC890SD/4/0361G

TMW408LL 198 135 14000 388 165 21000 19,40 38 AC890SD/4/0480H

TMW40ALH 270 145 17800 526 180 26800 25,10 48 AC890SD/4/0685K

TMW40CLG 318 140 21700 626 175 32500 25,90 57 AC890SD/4/0798K

150 - 175 rpm

TMW204LR 22 175 1210 47 215 1810 0,75 9 AC890SD/5/0059D

TMW206LR 33 165 1920 71 205 2850 0,81 13 AC890SD/4/073E

TMW207LR 39 165 2270 85 205 3380 1,00 16 AC890SD/4/0087E

TMW305LN 67 165 3880 133 205 5880 4,40 17 AC890SD/4/0145F

TMW306LN 82 165 4760 161 205 7200 4,55 21 AC890SD/4/0180F

TMW308LM 116 170 6530 225 210 9870 6,50 28 AC890SD/4/0250G

TMW30ALN 135 155 8330 268 190 12500 6,80 35 AC890SD/4/0316G

TMW406LI 185 175 10100 353 215 15300 16,20 29 AC890SD/4/0420H

TMW408LJ 226 155 13900 434 190 21000 19,40 38 AC890SD/4/0520H

TMW40ALE 324 175 17700 626 205 26800 25,10 48 AC890SD/4/0798K

175 - 200 rpm

TMW206LQ 40 200 1910 83 250 2850 0,81 13 AC890SD/4/0087E

TMW208LQ 55 200 2620 114 250 3910 1,03 18 AC890SD/4/0105F

TMW304LM 58 185 3000 114 230 4550 3,45 14 AC890SD/4/0105F

TMW306LL 99 200 4730 191 240 7200 4,55 21 AC890SD/4/0216G

TMW308LK 136 200 6490 261 250 9870 6,50 28 AC890SD/4/0316G

TMW30ALL 156 180 8290 305 225 12500 6,80 35 AC890SD/4/0361G

TMW406LH 209 200 10000 391 250 15300 16,20 29 AC890SD/4/0480H

TMW408LF 289 200 13800 538 250 21000 19,40 39 AC890SD/4/0590J

200 - 250 rpm

TMW205LQ 34 205 1560 70 255 2320 0,78 11 AC890SD/4/073E

TMW207LN 59 250 2260 119 310 3380 1,00 16 AC890SD/4/0105F

TMW208LP 63 230 2620 128 280 3910 1,03 18 AC890SD/4/0145F

TMW304LL 67 215 2980 128 265 4550 3,45 14 AC890SD/4/0145F

TMW305LK 87 215 3840 165 265 5880 4,40 18 AC890SD/4/0180F

TMW306LI 118 240 4690 224 300 7200 4,55 21 AC890SD/4/0250G

TMW308LH 165 245 6420 311 305 9870 6,50 29 AC890SD/4/0361G

TMW30ALJ 185 215 8230 354 265 12500 6,80 35 AC890SD/4/0420H

TMW30ALH 210 245 8170 396 305 12500 6,80 36 AC890SD/4/0480H

TMW406LG 239 230 9930 440 285 15300 16,20 30 AC890SD/4/0520H


Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 7


Modelpn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow

rate

(l/min)

Drive reference (2)

250 - 300 rpm

TMW204LP 35 280 1200 70 350 1810 - 9 AC890SD/4/0073E

TMW205LP 42 260 1550 85 325 2320 - 11 AC890SD/4/0087E

TMW206LM 60 300 1900 116 375 2850 - 14 AC890SD/4/0105F

TMW207LM 68 290 2250 134 360 3380 - 16 AC890SD/4/0145F

TMW304LH 90 295 2920 167 350 4550 - 15 AC890SD/4/0180F

TMW305LH 105 265 3800 196 325 5880 - 18 AC890SD/4/0216G

TMW305LF 116 295 3770 217 365 5880 - 18 AC890SD/4/0250G

TMW308LG 183 275 6370 343 340 9870 - 29 AC890SD/4/0420H

300 - 350 rpm

TMW204LM 45 355 1200 85 440 1810 - 9 AC890SD/4/0087E

TMW206LL 69 350 1890 131 435 2850 - 14 AC890SD/4/0145F

TMW208LL 84 310 2600 163 385 3910 - 18 AC890SD/4/0180F

TMW306LG 147 305 4610 271 370 7200 - 22 AC890SD/4/0316G

TMW306LF 154 320 4590 283 385 7200 - 22 AC890SD/4/0361G

350 - 400 rpm

TMW205LL 60 370 1540 113 460 2320 - 11 AC890SD/4/0105F

TMW205LK 64 400 1530 128 500 2320 - 11 AC890SD/4/0145F

TMW206LJ 79 400 1880 151 500 2850 - 14 AC890SD/4/0180F

TMW207LJ 88 375 2240 167 465 3380 - 16 AC890SD/4/0180F

TMW207LI 93 400 2230 181 500 3380 - 16 AC890SD/4/0216G

TMW208LJ 102 375 2580 193 465 3910 - 18 AC890SD/4/0216G

TMW208LH 108 400 2580 213 500 3910 - 18 AC890SD/4/0250G

TMW304LE 109 365 2860 199 425 4550 - 15 AC890SD/4/0216G

TMW304LC 119 400 2830 220 475 4550 - 15 AC890SD/4/0250G

TMW305LC 149 390 3660 271 450 5880 - 19 AC890SD/4/0316G



Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 398


Modelpn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow rate

(l/min)Drive reference (2)

50 - 75 rpm

TMW408LW 112 75 14200 196 90 21000 19,40 37 AC890SD/4/0216G

TMW40ALW 114 60 18100 219 70 26800 25,10 47 AC890SD/4/0250G

TMW40CLW 150 65 22000 271 75 32500 25,90 56 AC890SD/4/0316G

75 - 100 rpm

TMW305LU 35 85 3930 67 95 5880 4,40 17 AC890SD/4/0073E

TMW306LV 45 90 4820 86 100 7200 4,55 20 AC890SD/4/0087E

TMW30ALU 88 100 8410 162 120 12500 6,80 34 AC890SD/4/0180F

TMW406LV 97 90 10300 169 105 15300 16,20 28 AC890SD/4/0180F

TMW40ALQ 179 95 18000 312 115 26800 25,10 47 AC890SD/4/0361G

TMW40CLS 195 85 22000 347 100 32500 25,90 56 AC890SD/4/0420H

100 - 125 rpm

TMW304LR 40 125 3030 70 140 4550 3,45 14 AC890SD/4/0073E

TMW305LT 47 115 3920 84 135 5880 4,40 17 AC890SD/4/0087E

TMW308LU 76 110 6600 133 135 9870 6,50 27 AC890SD/4/0145F

TMW30ALS 110 125 8370 190 155 12500 6,80 34 AC890SD/4/0216G

TMW406LS 129 120 10200 215 145 15300 16,20 28 AC890SD/4/0250G

TMW408LS 155 105 14100 260 125 21000 19,40 38 AC890SD/4/0316G

TMW408LP 184 125 14100 304 145 21000 19,40 38 AC890SD/4/0361G

TMW40CLK 252 110 21800 426 130 32500 25,90 57 AC890SD/4/0520H

125 - 150 rpm

TMW204LU 19 150 1210 35 170 1810 0,75 9 AC890SD/5/0045D

TMW208LU 37 135 2630 71 150 3910 1,03 18 AC890SD/4/073E

TMW304LQ 47 150 3020 81 180 4550 3,45 14 AC890SD/4/0087E

TMW306LS 68 135 4790 114 165 7200 4,55 21 AC890SD/4/0105F

TMW308LQ 100 145 6560 167 175 9870 6,50 28 AC890SD/4/0180F

TMW30ALQ 127 145 8350 215 180 12500 6,80 34 AC890SD/4/0250G

TMW40ALM 243 130 17900 396 160 26800 25,10 47 AC890SD/4/0480H

TMW40ALK 271 145 17800 444 180 26800 25,10 48 AC890SD/4/0590J

TMW40CLI 329 145 21700 533 180 32500 25,90 57 AC890SD/4/0685K



Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 9


Modelpn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow rate


150 - 175 rpm

TMW205LT 25 155 1560 47 190 2320 0,78 11 AC890SD/5/0059D

TMW207LS 38 160 2270 70 195 3380 1,00 15 AC890SD/4/073E

TMW208LT 48 175 2630 86 215 3910 1,03 18 AC890SD/4/0087E

TMW305LP 71 175 3880 117 215 5880 4,40 17 AC890SD/4/0105F

TMW306LR 77 155 4770 128 190 7200 4,55 21 AC890SD/4/0145F

TMW308LN 120 175 6520 197 215 9870 6,50 28 AC890SD/4/0216G

TMW406LP 165 155 10100 264 190 15300 16,20 29 AC890SD/4/0316G

TMW408LL 240 165 13900 385 200 21000 19,40 38 AC890SD/4/0480H

TMW40ALH 324 175 17700 522 215 26800 25,10 48 AC890SD/4/0685K

TMW40CLG 394 175 21500 621 215 32500 25,90 57 AC890SD/4/0798K

175 - 200 rpm

TMW306LN 99 200 4730 160 245 7200 4,55 21 AC890SD/4/0180F

TMW30ALN 165 190 8270 267 230 12500 6,80 35 AC890SD/4/0316G

TMW406LJ 190 180 10100 304 215 15300 16,20 29 AC890SD/4/0361G

TMW408LJ 268 185 13800 431 225 21000 19,40 38 AC890SD/4/0520H

200 - 225 rpm

TMW204LR 27 215 1210 47 260 1810 0,75 9 AC890SD/5/0059D

TMW206LR 41 205 1910 71 250 2850 0,81 13 AC890SD/4/073E

TMW207LR 49 205 2270 84 250 3380 1,00 16 AC890SD/4/0087E

TMW304LM 70 225 2970 113 275 4550 3,45 14 AC890SD/4/0105F

TMW305LN 83 205 3850 132 250 5880 4,40 17 AC890SD/4/0145F

TMW308LM 139 205 6480 224 250 9870 6,50 28 AC890SD/4/0250G

TMW30ALL 189 220 8220 303 275 12500 6,80 35 AC890SD/4/0361G

TMW406LI 225 215 9970 349 260 15300 16,20 29 AC890SD/4/0420H

TMW40ALE 393 215 17500 619 250 26800 25,10 48 AC890SD/4/0798K

225 - 250 rpm

TMW206LQ 50 250 1900 83 310 2850 0,81 13 AC890SD/4/0087E

TMW208LQ 68 250 2610 114 310 3910 1,03 18 AC890SD/4/0105F

TMW306LL 120 245 4680 189 290 7200 4,55 21 AC890SD/4/0216G

TMW308LK 162 240 6430 259 300 9870 6,50 28 AC890SD/4/0316G

TMW406LH 249 240 9890 387 300 15300 16,20 29 AC890SD/4/0480H

TMW408LF 342 240 13600 532 295 21000 19,40 39 AC890SD/4/0590J



Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3910


Modelpn

(kw)

nn

(rpm)

Mn

(nm)

In

(arms)

nmax

(rpm)

Mmax

(nm)

Inertia

(kgm²)

water flow rate


250 - 300 rpm

TMW205LQ 42 255 1550 69 315 2320 0,78 11 AC890SD/4/073E

TMW208LP 78 285 2600 127 345 3910 1,03 18 AC890SD/4/0145F

TMW304LL 80 260 2950 127 320 4550 3,45 14 AC890SD/4/0145F

TMW305LK 104 260 3800 164 320 5880 4,40 18 AC890SD/4/0180F

TMW306LI 143 295 4620 221 365 7200 4,55 21 AC890SD/4/0250G

TMW308LH 199 300 6330 307 370 9870 6,50 29 AC890SD/4/0361G

TMW30ALJ 222 260 8140 351 320 12500 6,80 35 AC890SD/4/0420H

TMW30ALH 253 300 8060 391 370 12500 6,80 36 AC890SD/4/0480H

TMW406LG 281 275 9770 433 340 15300 16,20 30 AC890SD/4/0520H

300 - 350 rpm

TMW204LP 43 345 1200 69 430 1810 0,75 9 AC890SD/4/0073E

TMW205LP 52 320 1550 84 400 2320 0,78 11 AC890SD/4/0087E

TMW207LN 73 310 2250 118 380 3380 1,00 16 AC890SD/4/0105F

TMW305LH 125 320 3740 194 390 5880 4,40 18 AC890SD/4/0216G

TMW308LG 220 335 6270 338 410 9870 6,50 29 AC890SD/4/0420H

350 - 400 rpm

TMW206LM 72 365 1890 116 455 2850 0,81 14 AC890SD/4/0105F

TMW207LM 83 355 2240 134 440 3380 1,00 16 AC890SD/4/0145F

TMW208LL 102 375 2590 162 465 3910 1,03 18 AC890SD/4/0180F

TMW304LH 107 355 2870 164 420 4550 3,45 15 AC890SD/4/0180F

TMW305LF 139 360 3700 213 445 5880 4,40 18 AC890SD/4/0250G

TMW306LG 175 370 4520 266 445 7200 4,55 22 AC890SD/4/0316G

TMW306LF 181 385 4500 278 460 7200 4,55 22 AC890SD/4/0361G

400 - 450 rpm

TMW204LM 54 435 1190 85 535 1810 0,75 9 AC890SD/4/0087E

TMW205LL 72 450 1530 113 555 2320 0,78 11 AC890SD/4/0105F

TMW206LL 83 420 1880 131 520 2850 0,81 14 AC890SD/4/0145F

TMW207LJ 106 455 2220 166 560 3380 1,00 16 AC890SD/4/0180F

TMW208LJ 122 455 2570 192 560 3910 1,03 18 AC890SD/4/0216G

TMW304LE 129 440 2790 194 510 4550 3,45 15 AC890SD/4/0216G

450 - 500 rpm

TMW205LK 81 511 1520 127 630 2320 0,78 11 AC890SD/4/0145F

TMW206LJ 97 495 1860 150 615 2850 0,81 14 AC890SD/4/0180F

TMW207LI 116 500 2210 180 625 3380 1,00 16 AC890SD/4/0216G

TMW208LH 136 510 2550 211 635 3910 1,03 18 AC890SD/4/0250G

TMW304LC 143 500 2720 213 590 4550 3,45 15 AC890SD/4/0250G

TMW305LC 175 470 3550 264 540 5880 4,40 19 AC890SD/4/0316G



Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 11

Dimensions Drawings :

Shaft Height 200 mm / Thrust Bearing 29420*

Rear view Side view

Front view

Shaft End

Dimensions (mm)

Model L1 Max L2 Max L3 L4

TMW204 750 615 362 360

TMW205 750 615 362 360

TMW206 750 615 362 360

TMW208 850 715 462 460

* Other Thrust Bearings available, consult us.

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3912



Rear view Side view

Front view

Shaft End

Dimensions (mm)


TMW204 750 615 362 360

TMW205 750 615 362 360

TMW206 750 615 362 360

TMW208 850 715 462 460


Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 13



Front view

Shaft End

Dimensions (mm)


TMW406 880 720 310 250

TMW408 980 820 410 350

TMW40A 1180 1020 610 550

TMW40C 1180 1020 610 550

Rear view Side view


Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3914

T M W 3 0 6 L X C 2 0

product SeriesTM: Torque Motors

Cooling MethodW: Water coolingA: Natural Ventilation (available with derating, consult us)

Shaft Height20: 200 mm30: 315 mm40: 400 mm

Torque/Speed Characteristics(see motors data tables)

feedback SensorC: Remote Endat Encoder (Standard)B: Direct Endat Encoder (Option)A: Remote Resolver (Option)

Thrust BearingSee base configurations table below

TM Torque Motors Codification

Base Configurations

Motor Model Thrust Bearing availabilityordering Code

Thrust Bearing Mechanical Interface

TMW204...208SKF 29420 Standard 20 001

SKF 29424 Option 24 002

TMW304

SKF 29422 Standard 22 003

SKF 29426 Option 26 004

SKF 29430 Option 30 005

TMW305...30ASKF 29426 Standard 26 004

SKF 29430 Option 30 005

TMW406

SKF 29430 Standard 30 006

SKF 29434 Option 34 007

SKF 29440 Option 40 008

TMW407...40CSKF 29434 Standard 34 007

SKF 29440 Option 40 008

All No thrust bearing, with ball bearings

Option00 Consult us

All No thrust bearing, with roller bearings

Option01 Consult us

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 15

U F R 0 0 0 3

Mechanical InterfaceSee base configurations table on previous page

Shaft EndSee Table below

extruder Screw extraction/Cooling F: Frontside extruder screw extractionP: Frontside extruder screw extraction Extruder screw cooling possibilityR: Backside extruder screw extraction (consult us) Extruder screw cooling possibilityZ: No screw extraction - No screw cooling possibility

terminal boxU: Upper Rear (Standard)L: At the rear on the Left side (front view) (Option)R: At the rear on the Right side (front view) (Option)

Shaft End availability Code

Hollow Shaft with keyway Standard 0

Hollow Shaft with spline profile, module 0.8 Option 1

Hollow Shaft with spline profile, module 1 Option 2





Full shaft, smooth Option 7

Full shaft, with keyway Option 8

Other (Consult us) Option 9

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3916

Brushless servoMoTors NX series

from 0.45 n.m to 64 n.m

DESCRIPTIONThe NX series is the new brushless servo motor range. The NX series brushless servo motors are characterized by a 10-pole innovative design for highest quality of motion, improved torque density and a compact and robust design.With a large choice of torque and speed and an economical design, the NX series is the ideal solution for servo application.

230v AND 400v POweR SuPPLy mOtiON quALity AND HiGH DyNAmiC CHARACteRiStiCS ROBuSt AND COmPACt CONStRuCtiON ROtOR witH CONCeNtRAteD-fLux RARe eARtH mAGNetS 10-POLe DeSiGN ReSOLveR AS StANDARD , OPtiON POSivex® eCONOmiCAL ABSOLute eNCODeR, HiPeRfACe® eNCODeR BRAke OPtiON ADjuStABLe CONNeCtORS (exCePt Nx1) iP64* PROteCtiON (iP65 AS OPtiON) * NX8V : IP44

(1) NX1 to NX8 with connectors

Technical Specifications - NX SeriesRéférence CO

(N.m)IO

(Arms)Speed230V(rpm)

Speed400V(rpm)

Cmax*(N.m)

Imax*(N.m)

Inertie(kg.cm2)

NX110EAP 0.45 0.99 6000 - 1.71 3.95 1.3

NX205EAV 0.45 1.01 5000 7500 1.47 3.48 2.1

NX205EAS 0.45 1.4 7500 8900 1.47 4.8 2.1

NX210EAT 1 1.34 4000 6000 2.59 3.64 3.8

NX210EAP 1 1.99 6000 7000 2.59 5.43 3.8

NX310EAP 2 1.39 2300 4000 4.25 3.11 7.9

NX310EAK 2 2.43 4000 7000 4.25 5.44 7.9

NX420EAV 4 1.36 900 2000 8.3 2.97 29

NX420EAP 4 2.71 2300 4000 8.3 5.92 29

NX420EAJ 4 4.69 4000 6000 8.3 10.25 29

NX430EAF 5.5 6.64 4000 6000 12.3 15.68 42.6

NX430EAJ 5.5 5.24 3200 5500 12.3 12.38 42.6

NX430EAV 5.5 1.41 550 1000 12.3 3.33 42.6

NX430EAP 5.5 2.82 1700 3000 12.3 6.66 42.6

NX430EAL 5.5 3.78 2300 4000 12.3 8.93 42.6

NX620EAV 8 2.83 1100 2000 20 7.46 98

NX620EAR 8 5.31 2200 3900 20 14 98

NX620EAJ 8 9.89 4000 5700 20 26.1 98

NX630EAV 12 2.62 750 1350 30.1 6.92 147

NX630EAR 12 5.25 1450 2700 30.1 13.85 147

NX630EAK 12 9.86 2800 4900 30.1 26 147

NX630EAG 12 13.9 4000 5000 30.1 36.77 147

NX630EAN 12 7.92 2300 4000 30.1 20.9 147

NX820EAL 16 17.5 3600 6200 29.2 33.68 320

NX820EAX 16 5.16 1000 1900 29.2 9.91 320

NX820EAR 16 11 2200 3900 29.2 21.06 320

NX840EAJ 28 18.9 2200 3900 58.3 41.46 620

NX840EAQ 28 10.1 1200 2100 58.3 22.12 620

NX840EAK 28 16.8 2000 3500 58.3 36.87 620

NX860EAD 41 33 2600 3200 88.4 74.78 920

NX860EAJ 41 18.5 1450 2600 88.4 42.06 920

NX860VAG 64 39.1 2000 3400 94.9 61.5 920

NX860VAJ 64 29.3 1450 2600 94.9 45.79 920

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 17

NX1 and NX2 Dimensions (output wires version)

MotorN

(mm)

D

(mm)

E

(mm)

T

(mm)

P

(mm)

S

(mm)

M

(mm)

No brake With brake Fr* Fa*

Weight(kg)

L(mm)

Weight(kg)

L(mm) (daN) (daN)

NX110 30 9 25 2.5 42.5 3.2 50 0.8 110 1 141 15 6.9

NX205 40 11 25 2.5 56.5 5.5 63 0.8 100 1.1 137 28 15.5

NX210 40 11 25 2.5 56.5 5.5 63 1.3 120 1.6 157 30 16.7

* Fr and Fa not cumulative : At 1500 rpm for a bearing service life of 20000 hours

NX2 Dimensions (connector version)

MotorN

(mm)

D

(mm)

E

(mm)

T

(mm)

P

(mm)

S

(mm)

M

(mm)

No brake With brake Fr*

(daN)

Fa*

(daN)Weight

(kg)L

(mm)Weight

(kg)L

(mm)

NX205 40 11 25 2.5 56.5 5.5 63 0.8 100 1.1 137 28 15.5

NX210 40 11 25 2.5 56.5 5.5 63 1.3 120 1.6 157 30 16.7

NX3, NX4 and NX6 Dimensions

MotorN

(mm)

D

(mm)

E

(mm)

T

(mm)

P

(mm)

S

(mm)

M

(mm)


Weight(kg)

L(mm)

Weight(kg)

L(mm) (daN) (daN)

NX310 60 11 23 2.5 71 5.5 75-80 2 147 2.4 195 36 20

NX420 80 19 40 3 91.5 7 100 3.7 175 4.5 226 72 24

NX430 80 19 40 3 91.5 7 100 4.6 200 5.4 251 82 24

NX620 110 24 50 3.5 121 9 130 6.9 181 8 236 82 52

NX630 110 24 50 3.5 121 9 130 8.8 210 10 265 86 54* Fr and Fa not cumulative : At 1500 rpm for a bearing service life of 20000 hours


Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3918

NX8 Dimensions

Motor


Weight(kg)

L(mm)

Weight(kg)

L(mm) (daN) (daN)

NX820 13 200 16.5 266 151 28

NX840 20 260 23.5 326 165 33

NX860 27 320 30.5 386 172 37


NX8 Dimensions (ventilated version)

Motor


Weight(kg)

L(mm)

Weight(kg)

L(mm) (daN) (daN)

NX860V 30.5 424 34 490 172 37


Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 19

NX series : a roBusT aNd secure coNsTrucTioN

for high level perforMaNces

NX servo MoTor codificaTioN

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3920

NX series

ul recogNiTioN

DESCRIPTIONThe NX series is UL recognized for models with connectors.

Nx SeRieS witH CONNeCtORS iS uL ReCOGNizeD Nx1, Nx2 AND Nx8 uL veRSiON iS SLiGHtLy DiffeReNt fROm StANDARD veRSiON

Characteristics

Type Torque (N.m)

Temperature class

Length (mm) Connection

No brake With brake Output wires Connectors

NX1 0.31 A 134 141 not available NX110A - - R7- - -

NX2

NX205 0.4 A 129 137 NX205A - - R4- - - NX205A - - R7- - -

NX210 0.7 A 149 157 NX210A - - R4- - - NX210A - - R7- - -

NX3

NX3, 4, 6 and NX8 standard version with connectors is UL without specification (torque, insulation class, length) and codification change.

NX310E - - R7- - -

NX4 NX420E - - R7- - -NX430E - - R7- - -

NX6 NX620E - - R7- - -NX630E - - R7- - -

NX8NX820E - - R7- - -NX840E - - R7- - -NX860E - - R7- - -

NX8V (ventilated) Same specifications as standard version (torque, insulation class, length) but codification changes

Terminal box

NX860V - - R5 - - -

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 21

*Fr and Fa not cumulative - At 1500 rpm for a bearing service life of 20000 hours

Motor No brake With brake Fr* Fa* N D E T P S M Weight L Weight L (mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (mm) (kg) (mm) (daN) (daN)

NX110 30 9 25 2.5 42.5 3.2 50 0.8 134 1 141 15 6.9


For NX3, NX4, NX6 and NX8 drawings, please refer to pages 38 and 39


Motor No brake With brake Fr* Fa* N D E T P S M Weight L Weight L (mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (mm) (kg) (mm) (daN) (daN)NX205 40 11 25 2.5 56.5 5.5 63 0.8 129 1.1 137 28 15.5NX210 40 11 25 2.5 56.5 5.5 63 1.3 149 1.6 157 30 16.7


Motor No brake With brake Fr* Fa* N D E T P S M Weight L Weight L (mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (mm) (kg) (mm) (daN) (daN)

NX205 40 11 25 2.5 56.5 5.5 63 0.8 129 1.1 137 28 15.5

NX210 40 11 25 2.5 56.5 5.5 63 1.3 149 1.6 157 30 16.7


NX2 Dimensions (wire version)

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3922

aTeX servoMoTors

EX Serie

1.75 to 35n.m

DESCRIPTIONEX servo motors are “d” flameproof apparatus designed to operate in potentially explosive atmosphere according to 94/9/CE “New Approach” ATEX directive.Based on an innovative 10-pole design, they are characterised by an excellent motion quality for a high torque density.

«D» fLAmePROOf equiPmeNt iN ACCORDANCe witH Atex 94/9/Ce DiReCtive 230v OR 400v POweR SuPPLy iNteGRAteD tHeRmO-CONtACt AND tHeRmO-fuSe fOR tHeRmAL PROteCtiON BRAke OPtiON

TEChNICal SPECIfICaTIONS ex SeRvO mOtORS Classification : • II 2G EEx d IIB T4 (Gas) • or II 2GD EEx d IIB T4 IP65 T135°C (Gas & Dust)• Standard EN 50014, EN 50018 et EN 50281-1-1Protection :

thermo-switches and thermo-fuse inside winding for over-temperature protection

Connection : through flameproof cable glands for resolver and power (no pre-equipped cables)

Option : • With or without key • With or without brake

GA GeARBOxeS

Classification : • Standard EN 13463-1

EX Series - 230V power supplyMotor M0 N

max Inertia Weight

(N.m) (rpm) (kgm2.10-5) (kg)EX310EAP 1.75 2300 7.9 2.7EX310EAK 1.75 4000 7.9 2.7EX420EAP 3.5 2300 29 5EX420EAJ 3.5 4000 29 5EX430EAJ 4.8 3200 43 6EX430EAF 4.8 4000 43 6EX620EAO 6.6 2500 98 9.1EX630EAI 10.4 3000 147 11EX820EAR 14 2200 320 24EX820EAL 14 3600 320 24EX840EAJ 24.5 2200 620 32EX860EAD 35 2600 920 40

EX Series - 400V power supplyMotor M0 N

max Inertia Weight

(N.m) (rpm) (kgm2.10-5) (kg)EX310EAP 1.75 4000 7.9 2.7EX420EAV 3.5 2000 29 5EX420EAP 3.5 4000 29 5EX430EAP 4.8 3000 43 6EX430EAL 4.8 4000 43 6EX620EAO 7 4300 98 9.1EX630EAY 10.4 2900 147 11EX630EAN 10.4 4000 147 11EX820EAW 14 2200 320 24EX820EAR 14 3600 320 24EX840EAQ 24.5 2100 620 32EX840EAK 24.5 3300 620 32EX860EAJ 35 2600 920 40

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 23

eX3 DIMenSIonS

eX6 anD eX8 DIMenSIonS

eX4 DIMenSIonS

Dimensions

Motor L no brake with brakeEX310 225 255

EX3 Dimensions (mm)

EX4 Dimensions (mm)Motor L no brake with brakeEX420 265 290EX430 290 315

EX6 and EX8 Dimensions (mm)Motor N D E B P S M L no brake with brake

EX620 110 24 50 130 120 8.4 130 275 300EX630 110 24 50 130 120 8.4 130 300 325EX820 130 32 58 165 155 12 165 290 325EX840 130 32 58 165 155 12 165 350 385EX860 130 32 58 165 155 12 165 410 445

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3924

AC Servo Drives 637f / 638

1 to 30a

DESCRIPTION637f/638 servo drives series with integrated motion controller have been designed for the most demanding servo systems.Their ultra-fast control loops and process bus make them adapted to single or multi axis applications.Their EN954-1 category 3 safety input and their second optional application bus simplify their integration into machines.Furthermore, 637f/638 servo drives integrate advanced PLC functions which can be built-up with various input/ output options.Available as compact version, the 637f series is also offered as rack version, integrating up to 9 axes.

uLtRA-fASt CONtROL LOOP muLti AxiS SyNCHRONiSAtiON tHROuGH PROCeSS BuS APPLiCAtiON BuS : PROfiBuS-DP, DeviCeNet, … eN954-1 CAt. 3 SAfety OPtiON 1500 SteP iNteRNAL mOtiON CONtROLLeR eLeCtRONiC CAmS SimPLe COmmiSSiONiNG AND PROGRAmmiNG SOftwARe HiPeRfACe AND SSi eNCODeR iNPut, ... 230v OR 400v SuPPLy

TEChNICal SPECIfICaTIONSPower Supply - 1 or 3 phases 230 VAC ±10%, 50-60 Hz (638)3 phases 380-460VAC ±10%, 50-60 Hz (637f)Overload - 200% during 5 sec

Operating temperature - 0-40°C (derate by 2% per °C >40°C to 50°C max.)Altitude - 1000m (derate by 1% per 100m to 4000m max.)Humidity - 85% relative humidity non-condensing

Control Current loop 105µsSpeed loop 105µsPosition loop 105µs

Multi axis synchronization through process busVirtual master axisMulti axis synchronization

Embedded PLC functionsProgrammable electronic camTrajectory generator - 3 configurable independent blocks

Inputs/OutputsDigital Inputs : 10, incl. 8 configurable (638) 8, incl. 7 configurable (637f)Digital Outputs : 3 configurable Relay Outputs : 2, incl. 1 configurableAnalogue inputs 2 (0-10V, +/-10V)Analogue outputs 2 (+/-10V)Resolver feedback (standard) or Hiperface (option)Configurable encoder terminal : Incremental encoder input / output Absolute single or multi turn SSI encoder inputRS232 (COM1) serial communication port

Specifications

Model Power Supply

Output current

Continuous(Arms)

Peak(Arms)

638 A 01 1 or 3 ph. 230 VAC 1.0 2.0

638 A 02 1 or 3 ph. 230 VAC 2.0 4.0

638 A 04 1 or 3 ph. 230 VAC 4.0 8.0

638 A 06 1 or 3 ph. 230 VAC 6.0 12.0

637f K 02-6 3 ph. 380-460 VAC 2.0 4.0

637f K 04-6 3 ph. 380-460 VAC 4.0 8.0

637f K 06-6 3 ph. 380-460 VAC 6.0 12

637f K 10-6 3 ph. 380-460 VAC 10 20

637f K 16-6 3 ph. 380-460 VAC 16 32

637f K 22-6 3 ph. 380-460 VAC 22 44

637f K 30-6 3 ph. 380-460 VAC 30 60

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 25

sTaNdards

marked EN61800-3 (EMC compliance) with integral filter EN50178 (safety, low voltage)

and

DimensionsModel Current

ratingA

(mm)B

(mm)C

(mm)

638 All 56 250 232

637f 1 to 10 A 61,5 400 280

637f 10 to 30 A 104 400 280

637f

OPTIONSHiperface option4096 revolutions absolute encoder1048576 inc. per rev.Input/Output expansion options14 Digital inputs/10 Additional Digital outputs4 Digital inputs/4 Additional Digital outputs5 Digital inputs/2 Additional Digital outputsApplication communication option (COM2)RS232, RS422, RS485PROFIBUS-DPSUCOnet KDeviceNetCANopen DS402INTERBUS SInter axis communication option (COM3)CANopen cardCANopen card + 4 digital inputs extension/4 digital outputs

EN954-1 Category 3 safety option«Safe Stop»

638

Description TypeCoMplete SCreeneD CableS SetS wIth ConneCtorSPower Power cable with Molex connector for NX1, NX2 CS1UP1F9R00xxPower cable for NX and I0 <15Arms CS2UP1F1R00xxPower cable for NX and I0 <22Arms CS2UP2F1R00xxResolver Resolver cable for NX1, NX2 with Molex connectors CS1UA1F9R00xxResolver cable for NX CS1UA1F1R00xxxx = Length in m; standard Length 2, 5, 10m. ferrIteSFerrite for cable length > 15m (I<10A) FR3Ferrite for cable length > 15m (I>10A) FR6CoM2 CoMMunICatIon optIon RS232 Communication board RP232RS422 Communication board RP422RS485 Communication board RP485CAN / CANopen Communication board RPCANPROFIBUS DP Communication board RPPDPDeviceNet Communication board RPDEVSUCOnet-K Communication board RPSUCINTERBUS-S Communication board RPIBSCoM3 CoMMunICatIon optIon for 637fRPM2CA/637f-8 CANopen for 637f 02A to 10A RP 2CA-8RPM2CA/637f-16 CANopen for 637f 16A to 30A RP 2CA-16RPM2C8/637f-8 CANopen for 637f 02A to 10A RP 2C8-8RPM2C8/637f-16 CANopen for 637f 16A to 30A RP 2C8-16eXtenDeD I/o optIon boarD14 I/ 10 O digital for 637f RPEAEExternal plug 26 pins for RPEAE SUB D-HD 26 S/M SafetY MoDule optIon for 637fEN954-1 Cat.3 Safety module RP SBTeMC fIlterS for 637f230V 12A 1 phase RFI filter LNFE1-230/012230 ou 400V 8A 3 phases RFI filter LNFB3-480/008230 ou 400V 18A 3 phases RFI filter LNFB3-480/018400V 33A 3 phases RFI filter LNFB3-480/033400V 46A 3 phases RFI filter LNFB3-480/046400V 60A 3 phases RFI filter LNFB3-480/060400V 82A 3 phases RFI filter LNFB3-480/082400V 142A 3 phases RFI filter LNFB3-480/142eMC kItS 02A to 10A Kit for 637f EMVBU-D6K08V116A to 30A Kit for 637f EMVBU-D6K16V1output Choke (power Cable lenGth > 50m) Remark: Ferrite has also to be mounted Output choke In ≤ 8A E32-0011Output choke In ≤ 24A E32-0031Output choke In ≤ 35A E32-0046brake reSIStorResistor 100W 100W Ω B100/100-6Resistor 300W 33W Ω B300/33-6Resistor 560W 26W Ω B560/26-6SoftwareEASYRIDER / TESIWIN / PROGRAMMING EXAMPLES CD SERVOPC to 637f drive cable Kn PC/631-03.0

AAccessories

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3926

optionsteRmiNAL BOx ON ONe SiDePtC PROBeCLASS S BALANCiNGiP55 SeALBeARiNG ON Size 100ANti-CONDeNSAtiON HeAteR

DESCRIPTIONThe MA series is a family of asynchronous motors desi-gned to meet the requirement of dynamic or high speed applications.They are developed to work with 690P or 650V AC vector drives.

COmPACt SquARe fORm

SAme SizeS AS DC mOtORS witH SAme POweR

tHeRmAL PROBe

iNCRemeNtAL eNCODeR

iP54 OR iP23 PROteCtiON

CLASS f iNSuLAtiON ACCORDiNG tO eN60034 (ieC 34-1)AuxiLiARy veNtiLAtiON fOR NOmiNAL tORque At zeRO SPeeD

HiGH OveRLOAD CAPABiLity HiGH mAximum SPeeD

Technical Specifications - MA Series - IP23 - 3x400Vrms max..Motor Code Nom.

Speed

nn(rpm)

Nom. Power

Pn(Kw)

Nom. Torque

Tn(Kw)

Inertia

J(kgcm2)

Nom. Voltage

Vn(Vrms)

Nom. Current

In(Arms)

Magne-tizing

CurrentIµ

(Arms)

Nom. Frequency

Fn(Hz)

Max. speed at Pn

Nmax1(rpm)

Max. speed

Nmax1(rpm)

Weight

W(kg)

MA133 K K

FAG2

15002850

2136

134121

670670

395400

4168

1626

51.796.6

21003400

70007000

132132

MA133 S S

FAG2

15002600

2841

178151

860860

400380

5382

1834

51.888.1

15005900

70007000

157157

MA133 M M

FAG1

15002600

3144

197162

980980

400395

5986

2237

51.688.0

17004300

70007000

175175

MA133 P P

FAG1

15002600

3648

229176

12001200

400390

6897

2748

51.587.8

18005500

70007000

200200

MA160 M M

E1G1

11502550

4271

349266

24002400

380395

85132

2345

39.786.0

19003700

60006000

270270

MA160 l l

E1FA

11502200

4876

399330

30503050

380395

95143

2449

39.774.4

18003200

60006000

325325

MA160 P P

E1G1

11502400

5288

432350

36003600

390390

102171

3469

39.480.9

17004500

50005000

365365

MA180 M M

E1G1

11502500

78122

648466

50505050

395380

140225

4364

39.484.4

16004500

45004500

480480

MA180 P P

E2G1

11502500

101155

839592

63006300

390385

187285

6088

39.684.5

18004500

45004500

570570

MA225 S S

E1F1

11501800

114161

947854

1050010500

380390

217295

6081

39.360.9

20002700

35003500

640640

MA225 L L

E1F1

12001750

166218

13211190

1500015000

400400

299393

129169

41.059.3

16002300

35003500

860860

MA225 X X

E1F1

12001750

240314

19101713

2100021000

400400

433566

186243

41.159.4

16002300

35003500

11001110

coMpacT asyNchroNous MoTors Ma series

from 0.75 to 314 kw

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 27

Technical Specifications - MA Series - IP54 - 3x400Vrms max..Motor Code Nominal

Speed

nn(rpm)

Nominal Power

Pn(Kw)

Nominal Torque

Tn(Kw)

Inertia

J(kgcm2)

Nominal Voltage

Vn

(VRMS)

Nominal Current

In(ARMS)

Magne-tizing

CurrentIµ

(ARMS)

Nominal Frequency

Fn(Hz)

Max. speed at Pn

Nmax1(rpm)

Max. speed

Nmax1(rpm)

Weight

W(kg)

MA80 M M

F1H1

15003000

0.751.4

4.84.5

1212

380380

2.03.4

1.11.7

53.8104.0

64008200

90009000

1414

MA80 L L

F1H1

15003000

1.53.0

9.59.5

4949

390395

3.86.6

1.52.4

55.3106.0

26004200

90009000

2222

MA90 M M

F1H1

15003000

1.42.8

8.98.9

2727

340370

4.07.3

2.03.5

54.7104.7

45009000

90009000

2020

MA90 L L

F1H1

15003000

3.26.4

20.420.4

5858

365390

8.213.7

4.47.5

54.9105.0

90009000

90009000

3232

MA100 S S

FAG2

15003000

3.76.8

23.621.7

190190

380390

9.016.3

4.28.3

52.3102.1

26004700

80008000

5050

MA100 M M

FBG2

15003000

6.011.0

38.235.0

250250

385400

13.724.2

6.111.2

52.2102.1

24003600

80008000

6565

MA100 l l

FCG2

15003000

8.214.5

52.246.2

310310

390390

18.432.0

8.415.7

52.0101.9

24005000

80008000

8080

MA100 P P

FBG2

15003000

10.017.0

63.754.1

370370

380400

23.036.8

11.519.2

51.8101.6

31003900

80008000

9090

MA133 K K

FAG2

15002850

1628

10294

670670

390400

3456

1627

51.496.2

28004200

70007000

132132

MA133 S S

FAG2

15002850

2133

134111

860860

400400

4266

1933

51.396.1

20004200

70007000

157157

MA133 M M

FAG1

15002600

2434

153125

980980

395390

4871

2237

51.287.7

25006000

70007000

175175

MA133 P P

FAG1

15002600

3040

191147

12001200

400385

5885

2747

51.287.6

20007000

70007000

200200

MA160 M M

E1G1

12002600

3353

263195

24002400

400395

64103

2745

40.987.4

17004800

60006000

255255

MA160 L L

E1FA

12002200

3756

294243

30203020

400400

70111

2753

40.974.0

15003500

60006000

310310

MA160 P P

E1G1

12002400

4064

318255

36003600

400385

79134

3569

40.880.6

17005000

50005000

350350

MA180 M M

E1G1

12002500

5385

422325

50505050

400380

97159

4466

40.884.0

16004500

45004500

480480

MA180 P P

E2G1

12002500

64105

509401

63006300

390380

122199

5988

40.884.1

27004500

45004500

550550

MA225 S S

EBF1

12001800

77105

613557

1050010500

400395

142200

5491

40.660.5

16003500

35003500

640640

MA225 L L

E1F1

12001750

108142

863776

1500015000

400400

202264

87114

40.959.2

16002300

35003500

860860

MA225 X X

E1F1

12001750

156204

12401116

2100021000

400400

260381

125164

40.959.2

16002300

35003500

11001100

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3928

encoders

Encoder connection for MA100 to MA225 motors

1 pink Ch. /B2 blue Power supply encoder 10-30V3 red Top encoder4 black /Top encoder 5 brown Ch. A6 green Ch. /A7 purple /encoder defect8 grey Ch. B910 white-green 0V encoder11 white 0V encoder12 brown-green encoder Power supply 10-30V

Encoder connection for MA80 to MA90 motorsmax. speed 6000 rpmA red +VdcB green Ch. AC yellow Ch. BDE black 0 VoltF welded -G brown Ch. A*H orange Ch. B*I blue Ch. Z**J white Ch. Z**

TYPE: MS 3102 A18-1P with MS 3106 A18-1S

Ma series - diMeNsioNs

MA80 - MA90 DimensionsMotor DA E S F B L L1 KB P O W M K H Q Q1 N C R Z Z1 Z2 D T V d

MA80 M 100 60 3.5 40 255 320 - 9 175 151 195 165 9.5 80 205 219 130 101 184 79 82 8 19 21.5 6 M8

L 180 60 3.5 40 335 400 590 9 175 151 195 165 9.5 80 205 219 130 181 184 79 82 8 19 21.5 6 M8

MA90 M 125 70 3.5 50 293 448 - 9 190 165 215 165 12 90 230 240 130 123 192 108 110 / 24 27 8 M8

L 207 70 3.5 50 375 530 690 9 190 165 215 165 12 90 230 240 130 205 192 108 110 / 24 27 8 M8

FansMotor Ventilated

versionVoltage(Vrms)

Current(Arms)

frequency 50Hz

Noise(dB)

MA80 M-F1MA80 L-F1MA80 M-H1

- 230 0.09 54

MA80 L-H1 - 230 0.19 55

MA 90 M-F1MA 90 L-F1MA 90 M-H1

- 230 0.11 65

MA90 L-H1 - 230 0.37 63

MA100 IP54 - PVAP 200-225 0.33 66

MA133 IP54 - PVAP 200-275 0.59 74

MA133 IP23 - PVA 180-290 1.82 75

MA160 IP54 - PVAP 380-400 0.44 78

MA160 IP23 - PVA 175-265 4.5 82

MA180 IP54 - PVA 220-230 2.35 88

MA180 IP54 - PVAIP23 - PVA

IP54 - PVAP2180-230 8.3 85

MA225 IP54 - PVAP 220-230 5.5 96

MA225 IP54 - PVAIP23 - PVA

220-240220-240

10.310.3

9090

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 29

MA100 - MA133 - MA160 DimensionsMotor A E S F B L KB P O M K H G Q N C R Z D T V d

MA100 S 198 63 4 80 336 500 12 160 198 215 14 100 99 270 180 230 131 146 38 41 10 M12

M 258 63 4 80 396 560 12 160 198 215 14 100 99 270 180 280 131 146 38 41 10 M12

L 318 63 4 80 456 620 12 160 198 215 14 100 99 270 180 330 131 146 38 41 10 M12

P 378 63 4 80 516 680 12 160 198 215 14 100 99 270 180 390 131 146 38 41 10 M12

MA133 K 308 66 5 110 478 690 13 216 260 300 18 132 130 345 250 310 170 245 48 51.5 14 M16

S 368 66 5 110 538 750 13 216 260 300 18 132 130 345 250 370 170 245 48 51.5 14 M16

M 408 66 5 110 578 790 13 216 260 300 18 132 130 345 250 410 170 245 48 51.5 14 M16

P 473 66 5 110 643 855 13 216 260 300 18 132 130 345 250 475 170 245 48 51.5 14 M16

MA160 M 402 108 5 110 642 872 14 254 316 350 18 160 158 400 300 473 170 245 55 59 16 M20

L 482 108 5 110 722 952 14 254 316 350 18 160 158 400 300 553 170 245 55 59 16 M20

P 552 108 5 110 792 1022 14 254 316 350 18 160 158 400 300 623 170 245 55 59 16 M20

MA133 - MA160 - MA180 - MA225 DimensionsMotor A E S F B L KB P O M K* H G Q N C W R Z D T V d

MA133 K 308 66 5 110 435 646 13 216 293 300 18 132 166 558 250 101 356 170 245 48 51.5 14 M16

S 368 66 5 110 495 706 13 216 293 300 18 132 166 558 250 161 356 170 245 48 51.5 14 M16

M 408 66 5 110 535 746 13 216 293 300 18 132 166 558 250 201 356 170 245 48 51.5 14 M16

P 473 66 5 110 600 811 13 216 293 300 18 132 166 558 250 266 356 170 245 48 51.5 14 M16

MA160 M 402 108 5 110 628 835 14 254 349 350 18 160 200 637 300 228 419 170 245 55 59 16 M20

L 482 108 5 110 708 915 14 254 349 350 18 160 200 637 300 308 419 170 245 55 59 16 M20

P 552 108 5 110 778 985 14 254 349 350 18 160 200 637 300 378 419 170 245 55 59 16 M20

MA180 M 567 121 5 140 816 1039 15 279 394 350 18 180 220 740 300 344 505 267 337 60 64 18 M20

P 667 121 5 140 916 1139 15 279 394 350 18 180 220 740 300 444 505 267 337 60 64 18 M20

MA225 S 475 149 5 140 791 1047 19 356 482 400 18 225 270 880 350 267 595 267 337 75 79.5 20 M20

L 615 149 5 140 931 1187 19 356 482 400 18 225 270 880 350 407 595 267 337 75 79.5 20 M20

X 855 149 5 140 1171 1427 19 356 482 400 18 225 270 880 350 647 595 267 337 75 79.5 20 M20

IP54 - PVAP

MA 180-225 IP54-PVA MA 133-160-180-225 IP23-PVA Shaft end

Shaft end

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3930

sTaNdard asyNchroNous MoTors

Me/My series

0,18 to 315 kw

DESCRIPTIONThe ME/MY series is a range of standard high performance aluminium three phaseasynchronous motors (size 56 to 132) or cast iron (size 180 to over) especially suitable for use with 650/650V drives.

Motors dimensions are described on pages 22-25

Ordering informationWhen ordering, please indicate which mounting type will be used

TEChNICal SPECIfICaTIONS

HiGH effiCieNCy AND POweR fACtOR

ReDuCeD mAiNteNANCe COStS

LOw NOiSe LeveL

vOLtAGe 50Hz-380/415v AND 60Hz-440/480vHiGH tORque witH PROGReSSive ACCeLeRA- tiON At LOw CuRReNt

iP55 PROteCtiON

CLASS f iNSuLAtiON

CLASS B temPeRAtuRe RiSe

B3 fOOt mOuNtiNG, B5 OR B14 fLANGe mOuNtiNG By SimPLe PeRmutAtiON

MOTEURS 4 POLES 1500 rpm - Alimentation 400V *

RéférencesPn In N Rend. Cos fi Cn Bruit (dB) Inertie Poids

(kw) (A) (rpm) % - N.m Ch. Vide (kgcm²) (kg)

Me-xxxx-00632-4 0,2 0,6 1310 65 0,7 1,3 52 57 3,2 5

Me-xxxx-00711-4 0,3 0,7 1330 70 0,7 1,8 55 60 4,5 6,3

Me-xxxx-00712-4 0,4 1,0 1330 71 0,7 2,7 55 60 5,1 7

Me-xxxx-00801-4 0,6 1,4 1440 75 0,8 3,6 58 63 18 9,5

Me-xxxx-00802-4 0,8 1,9 1440 74,6 0,8 5,0 58 63 21 11

Me-xxxx-0090S-4 1,1 2,7 1400 76,2 0,8 7,5 61 66 21 14,5

Me-xxxx-0090L-4 1,5 3,5 1400 78,5 0,8 10,2 61 66 27 16

Me-xxxx-100L1-4 2,2 4,8 1430 81,5 0,8 14,7 64 69 540 23

Me-xxxx-100L2-4 3 6,4 1430 82,8 0,8 20,0 64 69 67 27

Me-xxxx-0112M-4 4 8,3 1435 84,4 0,8 26,6 65 70 95 33,5

Me-xxxx-0132S-4 5,5 11 1440 86,7 0,8 36,5 71 76 214 49,5

Me-xxxx-0132M-4 7,5 14,6 1440 88 0,8 49,7 71 76 296 57,5

Me-xxxx-0160M-4 11 21,2 1460 88 0,8 71,9 75 80 724 87

Me-xxxx-0160L-4 15 28,2 1460 89 0,9 98,1 75 79 929 94

My-xxxx-0180M-4 18,5 34 1470 90,5 0,9 120 76 80 - 182

My-xxxx-0180L-4 22 40 1470 91 0,9 143 76 80 - 190

My-xxxx-0200L-4 30 55 1470 92 0,9 195 79 83 - 270

My-xxxx-0225S-4 37 66 1475 92,5 0,9 240 81 85 - 284

My-xxxx-0225M-4 45 80 1475 92,8 0,9 291 81 84 - 320

My-xxxx-0250M-4 55 98 1475 93,1 0,9 356 83 86 - 427

My-xxxx-0280S-4 75 133 1485 93,8 0,9 482 86 89 - 562

My-xxxx-0280M-4 90 159 1485 94,2 0,9 579 86 89 - 667

My-xxxx-0315S-4 110 191 1485 94,5 0,9 707 93 96 - 1000

My-xxxx-0315M-4 132 229 1485 94,8 0,9 849 93 96 - 1100

* Other polarity available: 2, 6 and 8 poles. Consult us

CODIFICATION

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 31

MvMe-My, McMe-My aNd MvMcMe-My series

0,18 to 315 kw

DESCRIPTION The ME-MY asynchronous motors series is the base for the MV, MC and MVMC series, which include additional accessories used in demanding vector control applications: forced ventilation, PTC probe and encapsulated encoder.

Dimensions and mounting options of motors are identical to ME-MY series, pages 22 to 25.

LOw NOiSe LeveL iP55 PROteCtiON CLASS f iNSuLAtiON B3 fOOt mOuNtiNG, B5 OR B14 fLANGe mOuNtiNG By SimPLe PeRmutAtiON

encoderHEIDENHAIN ERN 430 type

10-30V Power supply

2048 pt/rev. (Other possible values as option)

Consumption: 350mA max with 300m cable

Outputs : totem-pôle A, /A, B, /B, Z, /Z

Temperature : -30 to +100°C (operating and storage)

IP64 Protection

Internal diameter : 12 mm (as option 8 or 10 mm)

Connection through plug on the motor

Forced ventilationShaft Heigth Absorbed Current

(A)230 V / 380 V / 400 V

Flowm3/h

FBI 056 0,1 / 0,06 / 0,06 250

FBI 063 0,1 / 0,06 / 0,06 250

FBI 071 0,1 / 0,06 / 0,06 250

FBI 080 0,15 / 0,09 / 0,09 330

FBI 090 0,21 / 0,13 / 0,12 500

FBI 100 0,21 / 0,13 / 0,12 660

FBI 112 0,21 / 0,13 / 0,12 900

FBI 132 0,25 / 0,15 / 0,14 780

FBI 160 0,33 / 0,20 / 0,19 1300

FBI 180 0,33 / 0,20 / 0,19 1300

FBI 200 0,83 / 0,50 / 0,48 2400

FBI 225 0,99 / 0,60 / 0,57 4200

FBI 250 1,16 / 0,70 / 0,67 4200

FBI 280 2,15 / 1,30 / 1,24 5000

FBI 315 2,31 / 1,4 / 1,33 6200

FBI 355 3,14 / 1,90 / 1,81 6500

Range

Accessories ME-MY MVME-MY

MCME-MY

MVMCME-MY

CTP Probe • • •

Forced ventilation • •

Encapsulated encoder • •

Encoder wiring

Terminals 1 2 3 4 5 6 7 8 9 10 11 12 Ground

Signal /B Z /Z A /A B 0V +Vp

Wires pink blue red black brown green purple grey white/green white brown/green yellow

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3932

Me-My series

Dimensions (mm)

Dimensions

Type Poles A B C D E H KL

AA AB AC AD BB HA HD LDE2/Y2 V C VC

56 2.4.6.8 90 71 36 9j6 20 56 6 192 - 292 - 25 110 121 - 90 8 154 45

63 2.4.6.8 100 80 40 11j6 23 63 7 215 405 315 405 34 120 121 - 110 8 165 49

71 2.4.6.8 112 90 45 14j6 30 71 7 250 440 350 440 36 132 137 - 120 9 180 49

80 2.4.6.8 125 100 50 19j6 40 80 10 280 482 380 482 41 152 156 - 132 10 205 51

90S 2.4.6.8 140 100 56 24j6 50 90 10 310 538 410 538 47 168 176 - 140 12 230 53

90L 2.4.6.8 140 125 56 24j6 50 90 10 335 563 435 563 47 168 176 - 165 12 230 53

100L 2.4.6.8 160 140 63 28j6 60 100 12 370 607 470 607 50 192 196 - 176 12 250 53

112M 2.4.6.8 190 140 70 28j6 60 112 12 395 623 495 623 60 222 220 - 180 14 280 57

132S 2.4.6.8 216 140 89 38k6 80 132 12 465 693 565 693 61 248 260 - 224 15 320 57

132M 2.4.6.8 216 178 89 38k6 80 132 12 495 723 595 723 61 248 260 - 224 15 320 57

160M 2.4.6.8 254 210 108 42k6 110 160 15 600 823 700 823 80 310 320 - 260 20 410 46

160L 2.4.6.8 254 254 108 42k6 110 160 15 640 863 740 863 80 310 320 - 260 20 410 146

180M 2.4.6.8 279 241 121 48 110 180 15 700 932 800 932 - 355 380 280 311 - 455 -

180L 2.4.6.8 279 279 121 48 110 180 15 740 972 840 972 - 355 380 280 349 - 455 -

200L 2.4.6.8 318 305 133 55 110 200 19 770 1043 870 1043 - 395 420 305 369 - 545 -

225S4.6.8 356 286 149 60 140 225 19 815 1094 915 1094 - 435 470 335 368 - 555 -

2 356 311 149 55 110 225 19 820 1099 920 1099 - 435 470 335 393 - 555 -

225M4.6.8 356 311 149 60 140 225 19 845 1124 945 1124 - 435 470 335 393 - 555 -

2 406 349 168 60 140 250 24 910 1196 1010 1196 - 490 510 370 455 - 615 -

2504.6.8 406 349 168 65 140 250 24 910 1196 1010 1196 - 490 510 370 455 - 615 -

2 457 368 190 65 140 280 24 985 1328 1085 1328 - 550 580 410 485 - 680 -

280S4.6.8 457 368 190 75 140 280 24 985 1328 1085 1328 - 550 580 410 485 - 680 -

2 457 419 190 65 140 280 24 1035 1378 1135 1378 - 550 580 410 536 - 680 -

280M4.6.8 457 419 190 75 140 280 24 1035 1378 1135 1378 - 550 580 410 536 - 680 -

2 508 406 216 65 140 315 28 1160 1505 1260 1505 - 635 645 530 570 - 845 -

315S4.6.8 508 406 216 80 170 315 28 1270 1615 1370 1615 - 635 645 530 570 - 845 -

2 508 457 216 65 140 315 28 1190 1535 1290 1535 - 635 645 530 680 - 845 -

315M4.6.8 508 457 216 80 170 315 28 1300 1645 1400 1645 - 635 645 530 680 - 845 -

2 508 508 216 65 140 315 28 1190 1535 1290 1535 - 635 645 530 680 - 845 -

315L4.6.8 508 508 216 80 170 315 28 1300 1645 1400 1645 - 635 645 530 680 - 845 -

2 610 560 254 75 140 355 28 1500 1850 1600 1850 - 730 710 655 750 - 1010 -

355M4.6.8 610 560 254 95 170 355 28 1530 1880 1630 1880 - 730 710 655 750 - 1010 -

2 610 560 254 75 140 355 28 1500 1850 1600 1850 - 730 710 655 750 - 1010 -

355L 4.6.8 610 560 254 95 170 355 28 1530 1880 1630 1880 - 730 710 655 750 - 1010 -

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 33

b3 foot Mounting

b5-b35 flange Mounting

B5 Flange

Type M N P S S num-ber T

56 100 80 120 7 4 3

63 115 95 140 10 4 3

71 130 110 160 10 4 3.5

80 165 130 200 12 4 3.5

90 165 130 200 12 4 3.5

100 215 180 250 15 4 4

112 215 180 250 15 4 4

132 265 230 300 15 4 4

160 300 250 350 19 4 5

180 300 250 350 19 4 5

200 350 300 400 19 8 5

225 400 350 450 19 8 5

250 500 450 550 19 8 5

280 500 450 550 19 8 5

315 600 550 660 24 8 6

355 740 680 800 24 8 6

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3934

BRIDE B14Types M N P S HD T L LD

56 65 50 80 M5 154 2.5 - 45

63 75 60 90 M5 165 2.5 405 49

71 85 70 105 M6 180 2.5 440 49

80 100 80 120 M6 205 3 482 51

90S 115 95 140 M8 230 3 538 53

90L 115 95 140 M8 230 3 563 53

100 130 110 160 M8 250 3.5 607 53

112 130 110 160 M8 280 3.5 623 57

132S 165 130 200 M10 320 3.5 693 57

132L 165 130 200 M10 320 3.5 723 57

b14-b34 flange Mounting

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 35

terminal box

Transmission Shaft

ARBRES BORNIER D’ALIMENTATION

Types Pôles D E F G GA GD DB X Y Z Presses étoupes

56 2.4.6.8 9j6 20 3 7.2 10.2 3 M3

92 92 50 2x M16x1.563 2.4.6.8 11j6 23 4 8.5 12.5 4 M4

71 2.4.6.8 14j6 30 5 11 16 5 M5

80 2.4.6.8 19j6 40 6 15.5 21.5 6 M6

90 2.4.6.8 24j6 50 8 20 27 7 M8100 100 51 2x M20x1.5

100 2.4.6.8 28j6 60 8 24 31 7 M10

112 2.4.6.8 28j6 60 8 24 31 7 M10112 112 59 2x M25x1.5

132 2.4.6.8 38j6 80 10 33 41 8 M12

160 2.4.6.8 42j6 110 12 37 45 8 M16 125 125 65 2x M32x1.5

180 2.4.6.8 48j6 110 14 42.5 - - - 150 160 105 2x M36x2

200 2.4.6.8 55j6 110 16 49 - - -

188 208 105 2x M48x2225S 2.4.6.8 60j6 140 18 53 - - -

225M2 55j6 110 16 53 - - -

4.6.8 60j6 140 18 58 - - -

2502 60j6 140 18 58 - - -

216 251 120 2x M64x2

4.6.8 65j6 140 18 67.5 - - -

280S2 65j7 140 18 58 - - -

4.6.8 75j6 140 20 71 - - -

280M2 65j6 140 18 58 - - -

4.6.8 75j6 140 20 71 - - -

315S2 65j6 140 18 58 - - -

300 358 198 2x M64x2

4.6.8 80j6 170 22 71 - - -

315M2 65j6 140 18 58 - - -

4.6.8 80j6 170 22 71 - - -

315L2 65j6 140 18 58 - - -

4.6.8 80j6 170 22 71 - - -

355M2 75j6 140 20 67.5 - - -

330 380 200 2x M72x24.6.8 95j6 170 25 86 - - -

355L2 75j6 140 20 67.5 - - -

4.6.8 95j6 170 25 86 - - -

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3936

TS8000 Series:

DLD/DuD/DSD Servo drives Series:• Economic and Compact Solution• Integrated EMC filter• Integrated braking resistor• 7 segments LCD Display

• Multilingual graphical interface• Pre-engineered projects• Built-in Web server• CompactFlash card slot• Integrated protocol conversion

SSD Parvex has been involved in the design and manufac-ture of electrical motors since its creation in 1948. Years after years, SSD Parvex managed to keep its know-how at the cutting edge of technology, building a complete range of AC, DC and torque motors.

Now part of Parker Hannifin’s group, SSD Parvex conti-nues to bring its unique know-how and experience accross various industries, serving machine builders as well as end-users.

• 1969 - DC Axem motors with flat rotor,• 1994 - Synchronous motors for electrospindles,• 1999 - Brushless servomotors in kit,• 2005 - Torque motors

SSD Parvex

Other SSD Parvex SOlutiOnS

SSD Parvex plant in Dijon

890 System drives: • 0,55 to 1000 kW• Power supply 380-500Vac +10%• Heating control of motor with prealarm• Standard Fieldbus : Profibus-DP, DeviceNet, Ethernet• System Drives for both AC & Servo motors

890PX Extruder driveSeries:• 30 to 400 kW• Energy supply 400V or 690V• Temperature monitoring with preventive alarm• Compact and modular structure

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 37

NOTES_________________________________________________________________________

____________________________________________________________________________________

______________________________________________________________________________________________________________________

______________________________________________________________________________________________________________________

____________________________________________________________________________________

___________________________________________________________________________________

_______________________________________________________________________________________________________________________

______________________________________________________________________________________________________________________

____________________________________________________________________________________

___________________________________________________________________________________

_______________________________________________________________________________________________________

_______________________________________________________________________________________________________

____________________________________________________________________________________

___________________________________________________________________________________

______________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________

____________________________________________________________________________________

___________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

____________________________________________________________________________________

___________________________________________________________________________________

_______________________________________________________________________________________________

______________________________________________________________________________________________

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 3938

NOTES___________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________________________________

____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

______________________________________________________________________________________________________

_____________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

____________________________________________________________________________________________________________________

____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_________________________________________________________________________________________________

________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

Tél: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39 39

NOTES___________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________________________________

____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________________________________

_____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

______________________________________________________________________________________________________

_____________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

____________________________________________________________________________________________________________________

____________________________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_________________________________________________________________________________________________

________________________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

Catalog “Extrusion/Converting” PVD3618/U.K - 09/2007

Parker SSD Parvex8, Avenue du Lac - B.P. 249 F-21007 Dijon Cedex Tel: +33 (0) 3 80 42 41 40 Fax: +33 (0) 3 80 42 41 39www.parker.com

Sales Offices

KR - South Korea, SeoulSSD Korea Co., Ltd #1308, Daeryung Techno Town 8th bldg, 481-11 Gasan-Dong, Geumchéon-Gu,Seoul 153-803, KoreaTel : +82 (0) 2 2163 6677Fax : +82 (0) 2 2163 8982

SE - Sweden, HalmstadSSD Drives ABMontörgatan 7 S-30260 HalmstadTel: +46 (0) 35 17 73 0Fax: +46 (0) 35 10 84 07

UK, United Kingdom,Electromechanical & Drives SalesParker Hannifin LtdTachbrook Park DriveTachbrook Park Warwick CV34 6TUTel: +44 (0) 1926 317970 Fax: +44 (0)1926 317980

US - USA, Charlotte/NCSSD Drives Inc9225 Forsyth Park Drive CharlotteNorth Carolina 28273Tel: +1 (704) 588 3246Fax: +1 (704) 588 3249

CA - Canada, Milton Parker Hannifin Canada - Motion and Control Division 160 Chisholm Drive Milton, Ontario L9T 3G9Tel: +1 (905) 693 3011 Fax: +1 (905) 876 0788

CN - China, ShanghaiParker China280, Yun Qiao Road, Jin Qiao Export Processing ZoneShanghai 201 206Tel: 86-21-2899 5000Tel: +86 10 6561 0520

DE - Germany, HeppenheimParker Hannifin GmbH & Co. KGVon-Humboldt-Strasse 10D-64646 HeppenheimTel: +49 (6252) 7982 00Fax: +49 (6252) 7982 05

DK - Denmark, VejleSSD Drives ABEnghavevej 11DK-7100 VejleTel: +45 (0) 70 201311Fax: +45 (0) 70 201312

PV

D36

18G

B E

d 2

007-

09-3

0

© 2007 Parker Hannifin Corporation. All rights reserved.

Your local authorized Parker distributor

ES - Spain, Gavá (Barcelona)Parker Hannifin GroupDelegación BarcelonaC/. Enginy n°6, nave 8Pol. Ind La PostE-08850 Gavá (Barcelona)Tel: +33 (0) 3 80 42 40 49Fax: +33 (0) 3 80 42 41 39

FR - France, DijonParker SSD Parvex SAS8, Avenue du LacBP 249F-21007 Dijon CedexTel: +33 (0) 3 80 42 41 40Fax: +33 3 80 42 41 39

IN - India, ChennaiSSD Drives India Pvt. Ltd151, Developed Plots EstatePerungudi, Chennai - 600 096Tel: +91 44 4391 0703Fax: +91 44 4313 2050

IT - Italy, Cinisello Balsamo /MI Parker Hannifin SpASSD SBCVia Gounod, 1I-20092 Cinisello Balsamo - MI Tel: +39 02 66012459Fax: +39 02 66012808

Date post:	06-Jul-2018
Category:	Documents
Upload:	trinhdung
View:	217 times
Download:	0 times

Solutions for Extrusion and Converting Drives and Servo...

Documents