Solutions for Mining – Field Projects

1 866-458-0101

smsequip.com

Scheduled & Unscheduled ShutdownsA scheduled shutdown is the most efficient and controllable means by which to effectively service, repair, and maintain large mining equipment such as shovels, draglines, haul trucks, and loaders. Due to the nature of mining, un-scheduled shutdowns are also a reality that SMS is well equipped to handle when a customer is in need.

Cable Shovel Maintenance & RepairsIncluding but not limited to:

• Overhauls for swing system, hoist systems, crowd systems, propel systems, point sheaves, and undercarriage

• Boom lowering and raising

• Suspension rope replacement

• Decommissioning disassembly

• Bucket fabrication

• Structural repairs for booms, sticks, buckets, revolving frames, and car bodies

• Line boring and machining

• Coupling and motor laser alignment

• Thermographic troubleshooting and audits

• Component repair and replacement

• Fault diagnosis and repair

• Machine relocation

• Parts supply and sales

Machining ServicesIncluding but not limited to:

• Portable Circular Surface Milling Machine capable of 8 – 21’ diameters

• Climax BB7100 5” line boring and facing from 10.25 - 58.25 inches

• Climax BB500 2.25” line boring and facing from 1.5 - 24 inches

Solutions for Mining – Field Projects

Hydraulic Shovels Maintenance & RepairsIncluding but not limited to:

• Component repair and replacement

• Overhauls for undercarriage

• Structural repairs for booms, sticks, buckets, revolving frames, and car bodies

• Line boring and machining

• Thermographic troubleshooting and audits

• Fault Diagnosis and repair

• Machine relocation

• Bucket fabrication

• Parts supply and sales

Dragline Maintenance & RepairsIncluding but not limited to:

• Overhauls for swing system, hoist systems, drag systems, propel systems, point sheaves, and fairleads

• Boom lowering and raising

• Suspension rope replacement

• Decommissioning disassembly

• Bucket Fabrication

• Structural repairs for booms, tubs, and revolving frames

• Line boring and machining

• Coupling and motor laser alignment

• Thermographic troubleshooting and audits

• Gearing supply and sales

Climax Surface Mill

WA1200 assembly in progress

Gahcho Kue PC5500 in progress

Whitewood 8200 dragline disassembly Did you know?Our Field Services group also has service capabilities for off-highway and remote locations. Some of the tooling available is:

• 3-53ft van body tool trailers fully equipped with gen sets, furnaces, and lunch rooms.

• Fully equipped mechanical trucks, welding trucks, crew trucks, and flatdecks all mine-site ready including: – beacons – buggy whips – radios – GPS

Lift-N-Lock SystemSMS Equipment has the capability to efficiently un-deck/separate cable and hydraulic shovels with its new Lift-N-Lock system. When the Lift-N-Lock system is set up and ready, an operator drives the shovel into position, and SMS personnel go to work lifting the house from the car body and separating the two. This procedure is reversed when putting the shovel back together. The efficiency of the system reduces down time up to 5 days, because the system is assembled and operational before the shovel arrives to the work pad. The SMS Equipment’s Lift-N-Lock system was built from suggestions and ideas from customers like you. This prototype our company put together, can lift up to 4.8 million pounds, has a 48-foot inside width, allows stick/bucket to stay on, and allows work to be done in the machine house. As well we can lower the house back to the ground so normal boarding and regular working heights are attainable. The 48 foot inside width allows for even the largest mining shovels, including oil-sands wide-track machines to move into the system without removing any major parts. We have had complete swing case rebuilds, outer panels replacement, crowd box repairs and extensive compartment welding while the shovel was in the Lift and Lock system.

• Single stage cylinder

• Fifteen foot eight inch stroke

• Wireless remote control

• Heated oil reservoirs

• Capacity 2,400 Ton / 4,800,000 Lbs.

• Foot print on four 6’ X 30’ mats 103,680 square inches

• P&H 4100XPC with Boom, Stick & Bucket the ground bearing pressure is 22 lbs. per sq. inch. Suspended on the LNL, a P&H 4100XPC with Boom, Stick & Bucket has a ground bearing pressure of approximately 22psi compared to the machine working pressure of approximately 37psi with 87” shoes

• Required hydraulic pressure to lift the estimated 2,200,000 lbs. is approximately 1200 psi.

• Specifically engineered to accommodate Oil sands wide-track machines

• Trained Staff for 24/7 Maintenance Projects

smsequip.com

We are registered and certified with ISO 9001:2008 conforming to regulatory standards and processes. We are continuously improving our Quality Management System to meet and exceed our customer quality and service requirements.

We are certified and registered with the CWB (Canadian Welding Bureau) and the Canadian Welding Association. Assuring com-pliance to proper standards, regulations and training services. All welders at the Acheson Reman facility are CWB certified.

We are members of the CWA (Canadian Welding Association) ensur- ing that we are meeting or exceeding current CSA standards. We also ensure that we are compliant to CWA quality assurance criteria.

Our CWB Certified Welding Inspectors are trained by the Inter- national NDT Education & Training Group to conduct various tests ensuring compliance to standards.

Patented Lift-N-Lock system in action

Safety Features:

• Front and rear stabilizing beams

• Centering struts in fourteen locations

• Spring applied cam locking system

• Low pressure system

• Spill proof containment

• Trained technicians to operate systems

Acheson Branch53113 Range Road 263AAcheson, AB T7X 5A5

1 866-458-0101smsequip.com