Micrologix 1000 Features Preconfigured 1K programming and data memory — help ease configuration (bit, integer, timers, counters, etc) Fast processing — allows for typical throughput time of 1.5 ms for a 500- instruction program Built-in EEPROM memory — retains all of your ladder logic and data if the controller loses power, eliminating the need for battery back-up or separate memory module RS-232 communication channel — allows for simple connectivity to a personal computer for program upload, download and monitoring using multiple protocols, including DF1 Full Duplex RTU slave protocol support — use DF1 Half-Duplex Slave, which allows up to 254 notes to communicate with a single master using radio modems, leased-line modems or satellite uplinks Product Design The MicroLogix 1000 controller contains the power supply, processor, and all its I/O circuits packaged in a single unit. Four I/O sizes (10, 16, 25, and 32) cover many applications.
Transcript
Micrologix 1000Features
Preconfigured 1K programming and data memory — help ease configuration (bit, integer, timers, counters, etc)
Fast processing — allows for typical throughput time of 1.5 ms for a 500-instruction program
Built-in EEPROM memory — retains all of your ladder logic and data if the controller loses power, eliminating the need for battery back-up or separate memory module
RS-232 communication channel — allows for simple connectivity to a personal computer for program upload, download and monitoring using multiple protocols, including DF1 Full Duplex
RTU slave protocol support — use DF1 Half-Duplex Slave, which allows up to 254 notes to communicate with a single master using radio modems, leased-line modems or satellite uplinks
Product Design
The MicroLogix 1000 controller contains the power supply, processor, and all its I/O circuits
packaged in a single unit.
Four I/O sizes (10, 16, 25, and 32) cover many applications.
Various electrical configurations of digital I/O offer you a controller that meets your electrical requirements:
o 24V DC inputs and relay outputs with a 24V DC
power supply.o 24V DC inputs and 24V DC FET and relay outputs
with a 24V DC power supply.
o 24V DC inputs and relay outputs with a
120/240V AC power supply.o 24V AC inputs and relay outputs with a
120/240V AC power supply.o 120V AC inputs and relay outputs with a
120/240V AC power supply.o 120V AC inputs and triAC and relay outputs with
a 120/240V AC power supply. Isolated relay contact outputs (at least two per
controller). Allow outputs on the same unit to switch different control voltages.
The 25-I/O models include 4 analog inputs and an analog output in addition to the 12 digital inputs and the 8 digital (contact) outputs.
Communication
Point-to-Point—RS-232 communication port configurable for direct connection to your programming device.
DH-485—RS-232 communication port configurable for DH-485 communication through an AIC+ (1761-NET-AIC) converter. Lets you communicate with SLC 500 processors, other MicroLogix controllers, operator interfaces, or programming devices in a DH-485 network.
EtherNet/IP—RS-232 communication port configurable for EtherNet/IP communication through an EtherNet/IP-to-RS-232 interface (1761-NET-ENI). The 1761-NET-ENI supports program monitoring and upload/download, data collection from PCs or mainframes, and controller peer-to-peer communication. It can also send e-mail messages via SMTP (Simple Mail Transfer Protocol), and can display status and configuration information through a built-in Internet server.
DeviceNet—RS-232 communication port configurable for communication through a DeviceNet interface (1761-NET-DNI) lets the controller function as a slave node in a DeviceNet network or as a peer to other controllers also using the 1761-NET-DNI interface.
DF1, half-duplex—RS-232 communication port configurable for DF1 half-duplex slave protocol for connection to a modem in SCADA applications.
Communication Port RS-232-C (Can be configured for communication through 1761-NET-AIC in a DH-485 network)
Relays are derated an additional 2.5g on 32 I/O controllers. DIN rail mounted controller is 1g.
MicroLogix 1000 Controllers
Cat. No. I/O
Digital Inputs
AnalogInputs
Digital Outputs
Analog Outputs
Real Input Power
Apparent Input Power
Transformer Load
1761-L10BWA 10 6 inputs24V DC sink/source
0 4 contact outputs
0 13W @ 120V AC14W @ 240V AC
24 VA @ 120V AC32 VA @ 240V AC
33 VA @ 120V AC35 VA @ 240V AC
1761-L10BWB 10 6 inputs24V DC sink/source
0 4 contact outputs
0 5W @ 24V DC
— —
1761-L10BXB 10 6 inputs24V DC sink/source
0 2 contact outputs2 source
0 5W @ 24V DC
— —
24V DC outputs
1761-L16AWA 16 10 inputs120V AC
0 6 contact outputs
0 7W @ 120V AC8W @ 240V AC
15 VA @ 120V AC21 VA @ 240 AC
18 VA @ 120V AC20 VA @ 240V AC
1761-L32AWA 32 20 inputs120V AC
0 12 contact outputs
0 9.1W @ 120V AC10.6W @ 240V AC
19 VA @ 120V AC25 VA @ 240V AC
23 VA @ 120V AC27 VA @ 240V AC
1761-L16BWA 16 10 inputs24V DC sink/source
0 6 contact outputs
0 14W @ 120V AC15W @ 240V AC
26 VA @ 120V AC33 VA @ 240V AC
35 VA @ 120V AC38 VA @ 240V AC
1761-L16NWA 16 10 inputs24V DC sink/source or 24V AC
0 6 contact outputs
0 14W @ 120V AC15W @ 240V AC
26 VA @ 120V AC33 VA @ 240V AC
35 VA @ 120V AC38 VA @ 240V AC
1761-L32BWA 32 20 inputs24V DC sink/source
0 12 contact outputs
0 15W @ 120V AC16W @ 240V AC
29 VA @ 120V AC36 VA @ 240V AC
38 VA @ 120V AC40 VA @ 240V AC
1761-L32AAA 32 20 inputs120V AC
0 10 triAC outputs, 120/240V AC2 contact outputs
0 7W @ 120V AC9W @ 240V AC
16 VA @ 120V AC22 VA @ 240V AC
18 VA @ 120V AC23 VA @ 240V AC
1761-L16BWB 16 10 inputs24V DC sink/source
0 6 contact outputs
0 5W @ 24V DC
— —
1761-L16NWB 16 10 inputs24V DC
0 6 contact outputs
0 5W @ 24V DC
— —
sink/source or24V AC
1761-L32BWB 32 20 inputs24V DC sink/source
0 12 contact outputs
0 7W @ 24V DC
— —
1761-L16BBB 16 10 inputs24V DCsink/source
0 4 source 24V DC outputs 2 contact outputs
0 5W @ 24V DC
— —
1761-L32BBB 32 20 inputs24V DC sink/source
0 10 source 24V DC outputs2 contact outputs
0 7W @ 24V DC
— —
1761-L20AWA-5A
25 12 inputs120V AC
2 voltage (±10V) 2 current (0…20 mA)
8 contact outputs
1 voltage/current(0…10V, 4…20 mA)
12W @ 120V AC13W @ 240V AC
20 VA @ 120V AC27 VA @ 240V AC
30 VA @ 120V AC33 VA @ 240V AC
1761-L20BWA-5A
25 12 inputs24V DC sink/source
2 voltage (±10V) 2 current (0…20 mA)
8 contact outputs
1 voltage/current(0…10V, 4…20 mA)
18W @ 120V AC19W @ 240V AC
30 VA @ 120V AC38 VA @ 240V AC
45 VA @ 120V AC48 VA @ 240V AC
1761-L20BWB-5A
25 12 inputs24V DC sink/source
2 voltage (±10V) 2 current (0…20 mA)
8 contact outputs
1 voltage/current(0…10V, 4…20 mA)
7W @ 24V DC
— —
Analog Input Specifications
Voltage Range ±10.5V -1LSB
Current Range 0…20 mA -1LSB
Data Format Natural binary 16-bit signed integer
Voltage Input Impedance
210 kW
Current Input Impedance
160 kW
Resolution 16 bits
Overall Accuracy 0…55 °C
±0.7% of full scale
Also a function of the input filter selection.
Analog Output Specifications
Voltage Range 0…10V -1LSB
Current Range 4…20 mA -1LSB
Data Format Natural binary 16-bit signed integer
Step Response 2.5 ms @ 95%
Load Range 0…500
Current Output Coding (4…20 mA -1LSB, 0…10V -1LSB)
0…32,767
Resolution 15 bits
Overall Accuracy 0…55 °C ±1.0% of full scale
System Overview
The MicroLogix 1000 family provides
small, economical programmable
controllers. They are available in
configurations of 10 digital I/O (6
inputs and 4 outputs), 16 digital I/O
(10 inputs and 6 outputs), 25 I/O (12
digital inputs, 4 analog inputs, 8 digital
outputs, and 1 analog output), or 32
digital I/O (20 inputs and 12 outputs) in
multiple electrical configurations of digital I/O. The I/O options and electrical configurations
make them ideal for many applications.
Benefits
Compact design—Lets the MicroLogix 1000 controller thrive in limited panel space.
Choice of communication networks—An RS-232-C communication port is configurable for: DF1 protocol for direct connection to a programming device or operator interface; DH-485 networking through a 1761-NET-AIC converter; DeviceNet networking through a 1761-NET-DNI interface; EtherNet/IP networking through a 1761-NET-ENI interface; or for half-duplex slave protocol in SCADA applications.
Simple programming with your choice of programming device—You can program these controllers in familiar
ladder logic with MicroLogix 1000 A.I. Series Software®, PLC 500 A. I. Series Programming Software, RSLogix 500™ Windows Programming Software, or the MicroLogix Hand-Held Programmer (1761-HHP-B30). This symbolic programming language is based on relay ladder wiring diagrams that simplify the creation and troubleshooting of your control program.
Comprehensive instruction set—Over 65 instructions including simple bit, timer, and counter instructions, as well as instructions for powerful applications like sequencers, high-speed counter, and shift registers.
9324-RL0100ENE RSLogix 500 Starter Edition Programming Software for SLC 500 and MicroLogix controller families. (CD-ROM)
9324-RL0300ENE RSLogix 500 Standard Edition Programming Software for SLC 500 and MicroLogix controller families. (CD-ROM)
9324-RL0700NXENE
RSLogix 500 Professional Edition. CD-ROM also includes RSLogix Emulate 500, RSNetWorx for DeviceNet and RSNetWorx for ControlNet.
RSLogix Emulate 500 Software
Test and debug all of your ladder logic programs prior to commissioning and startup. RSLogix Emulate 5, RSLogix Emulate 500 and RSLogix Emulate 5000 are Microsoft Windows-based software packages that emulate one or more PLC-5, SLC 500 or Logix5000 processors, respectively. You determine which PLC-5, SLC 500, Logix5000 ladder programs you want to run, and RSLogix Emulate scans the ladder logic like an actual processor. In addition, RSLogix Emulate 5000 has built-in support for all RSLogix 5000 supported languages such as ladder logic, function block, sequential function chart and structured text.
1763 MicroLogix 1100 Controllers
With online editing and a built-in 10/100 Mbps EtherNet/IP port for peer-to-
peer messaging, the MicroLogix 1100 controller adds greater connectivity
and application coverage to the MicroLogix family of Allen-Bradley
controllers. This next generation controller's built-in LCD screen displays
controller status, I/O status, and simple operator messages; enables bit and
integer manipulation; offers digital trim pot functionality, and a means to
make operating mode changes (Prog / Remote / Run).
With 10 digital inputs, 2 analog inputs and 6 digital outputs, the MicroLogix
1100 can handle a wide variety of tasks. The MicroLogix 1100 controllers
also support expansion I/O. Up to four 1762 I/O modules (also used on the
MicroLogix 1200 and 1400) may be added to the embedded I/O, providing
application flexibility and support of up to 80 digital I/O.
Features
Built-in 10/100 Mbps EtherNet/IP port for peer-to-peer messaging — offers users high speed connectivity between controllers, with the ability to access, monitor and program from anywhere an Ethernet connection is available
Online editing functionality — modifications can be made to a program while it is running, making fine tuning of an operating control system possible, including PID loops. Not only does this reduce development time, but it aids in troubleshooting
Embedded Web server — allows a user to custom configure data from the controller to be displayed as a web page
Isolated RS-232/RS-485 combo port — provides a host of different point-to-point and network protocols
Embedded LCD screen — allows user to monitor data within the controller, optionally modify that data, and interact with the control program. Displays status of embedded digital I/O and controller functions, and acts as a pair of digital trim pots to allow a user to tweak and tune a program
Cat. No. Function Communication Interface
Communication RatesSupported (bit/s)
Current Load
1761-NET-AIC AIC+ Advanced Interface Converter
Lets you connect a MicroLogix controller (or other DH-485 protocol-capable RS232-C device) to the DH-485 network. This allows the controller to initiate or respond to communication with any other device (SLC 500 processors, other MicroLogix controllers, operator interfaces, or programming devices) on the network. With the ability to initiate communication, the MicroLogix controller can act as a single initiator (also referred to as a master or parent) on the network.
3 ports:• 2 RS-232• 1 DH-485
DH-485 protocol on all ports for networking
• 600• 1200• 2400• 4800• 9600• 14400• 19200
• 120 mA @ 24V DC• 200 mA inrush at power turn-on
1761-NET-DNI
DeviceNet RS-232-C Interface
Lets you connect a MicroLogix controller (or other DF1 Full-duplex addressable RS-232-C device) to the DeviceNet network. This allows the controller to function as a DeviceNet slave node to provide 16 words of input data and 16 words of output data that can be exchanged with the DeviceNet scanner. This also allows peer-to peer messaging between controllers. Lets you connect a PC-compatible computer to the DeviceNet network for peer-to-peer messaging, for programming, and for on-line monitoring.
1761-NET-ENI EtherNet/IP Lets you connect a 10/100 Base-T EtherNet/ RS-232-C 100 mA @
RS-232-C Interface
MicroLogix controller (or other DF1 full-duplex addressable RS-232-C device) to the EtherNet/IP network. This module supports:• program monitoring and upload/download.• data collection from PCs or mainframe computers.• controller peer-to-peer communication.• sending e-mail messages via SMTP.• access to configuration reference information via the Internet through built-in web-page server.
(RJ45) Port with embedded LEDs
DF1 Full-duplex protocol on RS-232 port
IP10/100 MHz
selectable• 2400• 4800• 9600• 19200• 38400
24V DC
1761-NET-ENIW
EtherNet/IP RS-232-C Interface
Lets you connect a MicroLogix controller (or other DF1 full-duplex addressable RS-232-C device) to the EtherNet/IP network. This module supports:• program monitoring and upload/download.• data collection from PCs or mainframe computers.• controller peer-to-peer communication.• sending e-mail messages via SMTP.• access to configuration reference information via the Internet, and offers built-in user-configurable web-page server with read/write capability.
The Hand-Held Programmer (1761-HHP-B30) lets you create
and modify programs for your MicroLogix Controller, and
monitor programs through features such as textual fault
messages, trace, and multi-point monitoring.
Benefits
Optional EEPROM memory modules—Offer you two convenient and safe ways to store or transfer eight programs (maximum of 64K bytes) between MicroLogix 1000 Programmable Controllers. The memory module is located in the back of the HHP. The 1761-HHMK08 memory module has 8K bytes. The 1761-HHMK64 memory module has 64K bytes.
Trace function—You can quickly find faulty input elements that prevent an output from turning on or off, which saves valuable troubleshooting time.
Multi-point monitor—Lets you monitor your most crucial bit addresses at the same time. All 16 addresses are stored with the controller.
Simple user interface—Reduces your keystrokes when entering and monitoring programs.
Small size—Makes the Hand Held Programmer unit easy for you to carry around and store.
Global programmer—You can program in English, French, German, Italian, Spanish, and Japanese through a six language multilingual display.
