E2S Datasheet 2.2.4 v10b G205054 0786-CPD-20191 Part codes: Version: Part code: 24V dc SONF1DC24[x] 24V ac SONF1AC24[x] 115V ac SONF1AC115[x] 230V ac SONF1AC230[x] Suffix part number with ‘-UL’ for UL approved version A100 back box with mounting lugs: 24V dc SONF1DC24A[x] 24V ac SONF1AC24A[x] 115V ac SONF1AC115A[x] 230V ac SONF1AC230A[x] [x] = Housing colour: G: Grey R: Red W: White Features: • Automatic synchronisation on multi-sounder system. • Continuously rated. • Stainless steel fixings. • Mounting via internal BESA compatible fixing positions (standard version) or via external mounting lugs. • Duplicate cable terminations (in & out for daisy-chain installations). • Tropicalisation available on request. • Available with custom tone configurations and frequencies. Approvals: • VdS approved to EN54-3 (CPD 89/106/EEC). • UKOOA/PFEER compliant alarm tones. • UL approved version available. • GOST-R approved. Cert: POCC GB-JB05-B02228 Available as the SONFL1 alarm horn sounder & beacon combination unit. The SONF1 is a compact, high output, 100dB(A) alarm sounder. Low current consumption and high SPL in a robust fire retardant housing ensure the SONF1 is suitable for all general signalling applications including fire, security and process control. SONF1 Alarm Sounder
Transcript
E2S Datasheet 2.2.4 v10b
G205054
0786-CPD-20191
Part codes:Version: Part code:
24V dc SONF1DC24[x]
24V ac SONF1AC24[x]
115V ac SONF1AC115[x]
230V ac SONF1AC230[x]
Suffix part number with ‘-UL’ for UL approved version
A100 back box with mounting lugs:
24V dc SONF1DC24A[x]
24V ac SONF1AC24A[x]
115V ac SONF1AC115A[x]
230V ac SONF1AC230A[x]
[x] = Housing colour: G: Grey R: Red W: White
Features:• Automatic synchronisation on multi-sounder system.• Continuously rated.• Stainless steel fixings.• Mounting via internal BESA compatible fixing positions
(standard version) or via external mounting lugs.• Duplicate cable terminations
(in & out for daisy-chain installations).• Tropicalisation available on request.• Available with custom tone configurations
and frequencies.
Approvals:• VdS approved to EN54-3 (CPD 89/106/EEC).• UKOOA/PFEER compliant alarm tones.• UL approved version available.• GOST-R approved. Cert: POCC GB-JB05-B02228
Available as the SONFL1alarm horn sounder & beaconcombination unit.
The SONF1 is a compact, high output, 100dB(A) alarm sounder. Lowcurrent consumption and high SPL in a robust fire retardant housing ensurethe SONF1 is suitable for all general signalling applications including fire, security and process control.
SONF1 Alarm Sounder
Eddie
New Stamp
E2S Datasheet 2.2.4 v10b
E2S, Impress House, Mansell Road, London, UK, W3 7QH Telephone +44 20 8743 8880 www.e2s.comNo liability is accepted for any consequence of the use of this document. The technical specification of this unit is subject to change without notice due to our policy of continual product development. All dimensions are approximate. This unit is sold subject to our standard conditions of sale, a copy of which is available on request.
Specification:Maximum output: 100dB(A) @ 1 metre
Nominal output: 99dB(A) @ 1m +/- 3dB - Tone 1
No. of tones: 10 (UKOOA / PFEER compliant)
No. of stages: 2
Volume control: On board potentiometer
Effective range: 30m @ 1KHz
Voltages DC: 24V dc (10-30V dc) Reverse polarity diodeprotection on DC units.
Voltages AC: 24V ac; 115V ac; 230V ac
Ingress protection: IP66 (UL version Type 13 & 3R )
Housing material: High impact UL94 V0 & 5VA FR ABS
Colour: Red (RAL3000), grey (RAL7038) & white.
Cable entries: 4 x M20 clearance gland knockouts in side & back
Terminals: 0.5 to 1.5mm² cables.
Operating temperature: -25 to +55°C
Storage temperature: -40 to +70°C
Relative humidity: 90% at 20°C.
Weight : 0.30kg
Alarm sounder:Version: Voltage range: Current mA:
24V dc 10-30V dc 25mA
24V ac 50/60Hz +/-10% 40mA
115V ac 50/60Hz +/-10% 13mA
230V ac 50/60Hz +/-10% 13mA
SONF1 24V dc tone table:Stage 1 Frequency Description dB @ 1m Stage 2 Tone 1 800/1000Hz @ 0.25 sec Alternating - BS5839 Alarm tone 99dB(A) @ 1m Tone 8Tone 2 500/1200Hz @ 0.3Hz 0.5 sec Slow Whoop - NEN 2575:2000 100dB(A) @ 1m Tone 1Tone 3 1200/500Hz @ 1Hz - DIN / PFEER P.T.A.P. 99dB(A) @ 1m Tone 8Tone 4 544Hz (100mS)/440Hz (400mS) - AFNOR NF S 32-001 97dB(A) @ 1m Tone 9Tone 5 Bell 95dB(A) @ 1m Tone 1Tone 6 800/1000Hz @ 7Hz Sweeping 99dB(A) @ 1m Tone 8Tone 7 500-1200Hz 3.75sec /0.25sec. Australian Evac. 100dB(A) @ 1m Tone 10Tone 8 1000Hz Continuous - PFEER toxic gas 100dB(A) @ 1m -Tone 9 554Hz Continuous 97dB(A) @ 1m -Tone 10 420Hz @ 0.625 sec Australian Alert 97dB(A) @ 1m -
SONF1 115V ac and 230V ac tone table:Stage 1 Frequency Description dB @ 1mTone 1 800/1000Hz @ 0.25 sec Alternating - BS5839 Alarm tone 99dB(A) @ 1mTone 2 500/1200Hz @ 0.3Hz 0.5 sec Slow Whoop - NEN 2575:2000 100dB(A) @ 1mTone 3 1200/500Hz @ 1Hz - DIN / PFEER P.T.A.P. 99dB(A) @ 1mTone 4 544Hz (100mS)/440Hz (400mS) - AFNOR NF S 32-001 97dB(A) @ 1mTone 5 1000Hz Continuous - PFEER toxic gas 100dB(A) @ 1mTone 6 Bell 95dB(A) @ 1mTone 7 800/1000Hz @ 7Hz Sweeping 99dB(A) @ 1mTone 8 2400/2900Hz @ 50Hz Sweeping 100dB(A) @ 1mTone 9 420Hz @ 0.625 sec Australian Alert 97dB(A) @ 1mTone 10 500-1200Hz 3.75sec /0.25sec. Australian Evac. 100dB(A) @ 1m
Country specific or custom tone configurations and alarm frequencies are available upon request.
*SPL data +/-3dB(A). Measured at optimum voltage.
64.50 mm
86.0
0 m
m
86.00 mm�6.00 mm
98.0
0 m
m
86.0
0 m
m86.00 mm
55.50 mm
Eddie
New Stamp
Tel : 0044(0)2087438880 mail : [email protected] Fax : 0044(0)2087404200 web : www.e2s.com
IN
STA
LL
AT
ION
IN
ST
RU
CT
ION
SSONF1 AC - 10 Tone ‘Sonora’
•Volume Control•Réglage du volume•Steuerung der Lautstärke•Controllo volume•Controlo do Volume•Control Volumen•Volumen kontrol•Volum eregeling•Volum kontro ll•Volym kontro ll
• Tone selection. To select a tone place the pin link in the position shown above (Fig. 1).
• Sélection de la tonalité / réglage des commutateurs. Pour sélectionner une tonalité, mettre les socles à broches dans lespositions illustrées (Fig. 1).
• Tonwahl / Einstellung der Schalter. Zur Wahl eines Tons die Klemmenanschlüsse in die angegebenen Positionen bringen (Fig.1).
• Selezione tono / regolazione commutatore. Per selezionare un tono, disporre i collegamenti a cavallotto nelle posizioniindicate (Fig. 1).
• Seleção de tons / ajuste dos comutadores. Para seleccionar um tom, coloque as ligações dos pinos na posição mostrada (Fig.1)
• Selección Tono / programación interruptores. Para seleccionar un tono colocar las conexiones de los puentes en las posicionesmostradas (Fig. 1).
• Toonselectie. Om een toon te selecteren de pinverbinding in de hierboven aangetoonde positie plaatsen (Fig. 1)
• Valg af tone. Valg af en tone sker ved at anbringe stiftforbindelsen i ovenstående position (fig. 1).
• Velge tone. For å velge en tone må du plassere stiftleddet i posisjonen som vist ovenfor (fig. 1).
• Tonval. Välj en ton genom att placera stiftanslutningen i läget som visas ovan (fig. 1).
ISN0602-ANo liabil ity i s acce pted for an y con sequen ce of the u se of this docume nt. T he technica l specifica tion o f thi s unit issub ject to chan ge wi thout notice due to our policy of contin ual product devel opment . All dimen sions areapp roxima te.Thi s uni t is sold su bject to ou r stan dard condit ions of sal e, a copy o f which is a vaila ble on reque st.
Tone 1 Tone 2 Tone 3 Tone 4 Tone 5 Tone 6 Tone 7 Tone 8 Tone 9 Tone 10
Tel : 0044(0)2087438880 mail : [email protected] Fax : 0044(0)2087404200 web : www.e2s.com
IN
STA
LL
AT
ION
IN
ST
RU
CT
ION
SSONF1 AC - 10 Tone ‘Sonora’
•Volume Control•Réglage du volume•Steuerung der Lautstärke•Controllo volume•Controlo do Volume•Control Volumen•Volumen kontrol•Volum eregeling•Volum kontro ll•Volym kontro ll
• Tone selection. To select a tone place the pin link in the position shown above (Fig. 1).
• Sélection de la tonalité / réglage des commutateurs. Pour sélectionner une tonalité, mettre les socles à broches dans lespositions illustrées (Fig. 1).
• Tonwahl / Einstellung der Schalter. Zur Wahl eines Tons die Klemmenanschlüsse in die angegebenen Positionen bringen (Fig.1).
• Selezione tono / regolazione commutatore. Per selezionare un tono, disporre i collegamenti a cavallotto nelle posizioniindicate (Fig. 1).
• Seleção de tons / ajuste dos comutadores. Para seleccionar um tom, coloque as ligações dos pinos na posição mostrada (Fig.1)
• Selección Tono / programación interruptores. Para seleccionar un tono colocar las conexiones de los puentes en las posicionesmostradas (Fig. 1).
• Toonselectie. Om een toon te selecteren de pinverbinding in de hierboven aangetoonde positie plaatsen (Fig. 1)
• Valg af tone. Valg af en tone sker ved at anbringe stiftforbindelsen i ovenstående position (fig. 1).
• Velge tone. For å velge en tone må du plassere stiftleddet i posisjonen som vist ovenfor (fig. 1).
• Tonval. Välj en ton genom att placera stiftanslutningen i läget som visas ovan (fig. 1).
ISN0602-ANo liabil ity i s acce pted for an y con sequen ce of the u se of this docume nt. T he technica l specifica tion o f thi s unit issub ject to chan ge wi thout notice due to our policy of contin ual product devel opment . All dimen sions areapp roxima te.Thi s uni t is sold su bject to ou r stan dard condit ions of sal e, a copy o f which is a vaila ble on reque st.
Tone 1 Tone 2 Tone 3 Tone 4 Tone 5 Tone 6 Tone 7 Tone 8 Tone 9 Tone 10
