Sony A 55 Manual 081800 Manual

4-075-080-21 (1)

1999 by Sony Electronics Inc. Reproduction in whole or in part without writtenpermission is prohibited. All rights reserved.

DIRECTV Digital Satellite Receiver

Operating Instructions

SAT-A55SAT-B55

Before you begin using your Digital Satellite Receiver for the first time, follow the instructions in Connecting Your Digital Satellite Receiver on pages 6-13 and Setting Up Your Digital Satellite Receiver (SYSTEM) on pages 22-34.Also, make sure your Satellite Dish Antenna has been properly installed and call your service provider to begin service:DIRECTV: 1-800-DIRECTV (347-3288)

SAT-A55 MODEL ONLYRF ANTENNA: This Digital Satellite Receiver is shipped with IR reception enabled and RF reception disabled. To use the RF feature (and the RF Antenna) you must change the factory setting (IR only) to the RF setting (RF only) using the on-screen displays, as described in these Operating Instructions.

2

To reduce the risk of fire or shock hazard, do not expose the unitto rain or moisture.

This symbol is intended to alert the user to thepresence of uninsulated dangerous voltagewithin the products enclosure that may be ofsignificant magnitude to constitute a risk ofelectric shock to persons.

This symbol is intended to alert the user to thepresence of important operating andmaintenance (servicing) instructions in theliterature accompanying the appliance.

Note to the CATV InstallerThis reminder is provided to call the CATV system installersattention to Article 820-40 of the NEC that provides guidelines forproper grounding and, in particular, specifies that the cableground shall be connected to the grounding system of the buildingas close to the point of cable entry as practical.

Note to the Satellite Dish Antenna InstallerThis reminder is provided to call the Satellite Dish Antennainstallers attention to Article 810 and in particular Article 810-15of the NEC, which covers proper installation and grounding oftelevision receiving equipment, as well as to Article 820-40 of theNEC, which specifies that the Satellite Dish Antenna cable groundshall be connected to the grounding system of the building as closeto the point of cable entry as practical.

Telephone Line InterruptionPeriodically, information on your DIRECT TICKET and Pay PerView selections is sent, free of charge, via your telephone line to an800 number. If you use your telephone during the time theinformation is being forwarded, you will hear static noise forapproximately 30 seconds. If youwould like to use your telephonewhile the information is being sent, you can interrupt the sendingof this information at any time by temporarily unplugging thephone line to the receiver.

Local ProgrammingWith this Digital Satellite Receiver and a DIRECTV Plus satellitedish antenna, you may be able to receive local channels fromDIRECTV in certain areas. Additional equipment may be requiredin some areas. Checkwith your retailer or visitwww.directv.com forinformation on availability of local channels from DIRECTV inyour area.

The Digital Satellite Receiver is intended for use only within theUnited States.

The model and serial numbers are located on the bottom of theDigital Satellite Receiver. The number for theAccess Card is on theback of the card and on the carton label. Record these numbers inthe space provided below. Refer to these numbers whenever youneed to call your sales or service representative regarding thisproduct.

For ProgrammingFor subscription information, or to resolve problems related toprogramming, call:DIRECTV at 1-800-DIRECTV (347-3288)

For Hardware and InstallationTo arrange for the installation of your Digital Satellite Receiver,call the dealer from whom you purchased your system.For general information, or to resolve problems related to theoperation of your Digital Satellite Receiver or Satellite DishAntenna, please contact your Sony dealer. If your dealer orinstaller is unable to answer your questions, call the Sony SatelliteSystem Information Center at 1-800-838-7669.

Trademark and CopyrightsSony, Media Window, Signal Seeker, Remote Commander andSmartFile are trademarks of Sony. DIRECTV is a trademark ofDIRECTV, Inc., a unit of Hughes Electronics, and is used withpermission.Manufactured under license from Dolby Laboratories. Dolbyand the double-D symbol are trademarks of Dolby Laboratories.Confidential Unpublished Works. 19921997 DolbyLaboratories Inc. All rights reserved.

Macrovision InformationThis product incorporates copyright protection technology that isprotected by U.S. patents and other intellectual property rights.Use of this copyright protection technology is granted byMacrovision for home and other limited pay per view uses only.Reverse engineering or disassembly is prohibited.

Note on Recording ProgrammingProgramming may be taped for home viewing only. All othertaping is expressly prohibited. Some programming may not betaped. An additional taping fee may be applied. Call yourprogram providers for details.

StarSight LicensedThe manufacture and sale of the television schedule feature of thisproduct was licensed under one or more of the following patentsof StarSight Telecast, Inc.: U.S. Patent Nos. 4,706,121; 4,977,455;5,151,789; and 5,353,121; with use rights reserved.

These Operating Instructions describe how to use the SAT-A55and its remote control. Any differences in operation for theSAT-B55 are noted in the text.The z icon indicates hints and tips for making the task easier.A Note provides information that may be necessary to completethe task.

You are cautioned that any changes or modifications notexpressly approved in thismanual could void your authority tooperate this equipment.

WARNING

Attention

Model Number:

Serial Number:

Access Card Number:

Owners Record

Customer Support

About These Operating Instructions

S

SATELLITERECEIVER

+

2

8

3

4 5 6

9

1

7

0

Connecting Your Digital Satellite Receiver (Page 6)

Using Your Remote Control (Page 14)

Setting Up Your Digital Satellite Receiver (Page 22)

Using the Program Guide (Page 37)

Using the Favorite Stations Guide (Page 40)

Setting Locks & Limits (Page 53)

Getting to Know Your Digital Satellite Receiver3

4

Features

Congratulations on your purchase of the Sony Digital Satellite Receiver. This manual canhelp you to become familiar with the many great features of the Digital Satellite Receiver.Check below to find out about some of the most exciting features.

Convenience and Ease-of-Use The ProgramGuide shows the picture and sound in theMediaWindowwhile you checkstation and program information. See page 37.

The One Button Record and VCR Control features allow you to easily record your favoriteprogramming on your VCR. See pages 2628 and page 60.

SAT-A55 model: Operate your Digital Satellite Receiver from another room or fromoutside a cabinet by setting up the RF feature on your remote control. See pages 3234.

Excellent Performance The Auto Title Insert feature for VCR recording can display program information at thebeginning of any Timer & Rec event. Youll have a convenient title recorded at thebeginning of your tapes. See page 26.

Choose to listen to different audio tracks available with many programs. See page 64

SAT-A55 model: Select Dolby Digital audio to truly make your home theater come alive.See page 64.

Easy to Customize Organize the channels your family watches most often by setting up the Favorite Stationsguide. See pages 4042.

Control access to programming with the Locks & Limits feature. See pages 5358.

Set up the Custom Stations feature to exclude stations that you dont want to see from theProgram Guide, Category Guide and Station Index. See pages 5051.

Choose your favorite color palette for the on-screen displays. See pages 4748

Using

theOn-Screen

Displays

Connecting

Your

Digital

SatelliteReceiver

5

View

ingPictures

FromYour

DigitalSatellite

Receiver

Other

Information

Table of Contents

Connecting Your Digital Satellite ReceiverCarton Contents ................................................... 6

Connection Overview .......................................... 7

Step 1: Inserting the Batteries ............................. 7

Step 2: Connecting the Satellite Dish Antenna and Telephone Line ........................................... 8

Step 3: Connecting Your TV ................................. 9

Step 4: Adding a VCR and Audio System ......... 10

Step 5: Connecting the VCR Controller ............. 11Connecting a Sony SmartFile VCR .................................. 11

Step 6: Connecting the RF Antenna (SAT-A55 only) ................................................. 12

Step 7: Connecting the AC Power Cord ............ 13

Step 8: Inserting the Access Card ...................... 13

Viewing Pictures From Your Digital Satellite ReceiverUsing Your Remote Control ............................... 14

RM-Y802 Remote Control (SAT-A55 model) ..................... 14

RM-Y139 Remote Control (SAT-B55 model) ...................... 16

Selecting Items ................................................... 18

Turning On the Power ....................................... 19

Changing Channels ............................................ 20

Using the On-Screen DisplaysUsing the Main Menu ........................................ 21

Setting Up Your Digital Satellite Receiver (SYSTEM) .......................................................... 22Using the System Menu ..................................................... 22

Setting Up the Satellite Dish Antenna .............................. 23

Setting Up the VCR Control Feature .................................. 26

Performing a System Test .................................................. 29

Setting the Aspect Ratio ..................................................... 30

Replacing Your Access Card ............................................... 31

Selecting RF or IR Remote Control Reception (SAT-A55 only) ................................................................. 32

Using the Guides Menu ...................................................... 35

Viewing Station and Program Information (GUIDES) ........................................................... 35Using the Alpha List ............................................................ 36

Using the Program Guide ................................................... 37

Using the Category Guide .................................................. 38

Using the Station Index ...................................................... 39

Using the Favorite Stations Guide ..................................... 40

Using Other Guides ............................................................. 43

Viewing Pay Per View Programs ........................................ 45

Adjusting the Displays (PREFERENCES) .................................................46Using the Preferences Menu .............................................. 46

Setting Display Options ...................................................... 47

Setting Up Custom Stations ............................................... 50

Selecting Data Services ....................................................... 51

Viewing Messages (MESSAGES) .....................................................52

Setting Locks and Limits (LOCKS & LIMITS) .............................................53Using the Locks & Limits Display ........................................ 53

Locking Your Receiver ......................................................... 57

Unlocking Your Receiver ..................................................... 58

Checking Pay Per View Purchases (PURCHASES) ....................................................59Checking Your Purchases .................................................... 59

Scheduling Programs (TIMER & REC) ..................................................60Using One Button Timer & Rec ........................................... 60

Using the Timer & Rec Feature ........................................... 61

Editing Timer Events ........................................................... 63

Setting Audio Options (AUDIO) ............................................................64Using the Audio Display ..................................................... 64

Other InformationSetting Up the Remote Control .........................65

Manufacturer Codes ...........................................66

Location and Function of Controls ....................68Front Panel ........................................................................... 68

SAT-A55 Back Panel ............................................................. 69

SAT-B55 Back Panel ............................................................. 70

Specifications ......................................................71

Troubleshooting .................................................72

FCC Regulations and Information ......................76

Limited Warranty ................................................77

Index ....................................................................78

6

Connecting Your Digital Satellite Receiver

Carton ContentsCheck to make sure the following items are in the Digital SatelliteReceivers carton.If you are missing any items, contact your Sony dealer.

* The RM-Y802 Remote Control shown.** The RF Antenna and S-Video cable are not included with the SAT-B55

model.

NoteKeep the original carton and packing materials to safely transport the Digital SatelliteReceiver in the future.

Digital Satellite Receiver

Access Card

S

SATE

LLITE

RECE

IVER

+ 2

8

3

45

691

7 0

AC Power Cord

Telephone Cord

RF Antenna**

Remote Control*

Size AA Batteries VCR Controller Audio/Video Cable

RF Coaxial Cable S-Video Cable**

Connecting

Your

Digital

SatelliteReceiver

Connection Overview

Step 1: Inserting the BatteriesFollow the procedures or make the connections ineach of the steps to connect your Digital SatelliteReceiver.

Before you can use the remote control, you mustinsert the supplied batteries. If you want to use thisremote control to operate other audio/videoequipment, such as a TV or VCR, youmust set up theremote control (see page 65).

1 Push and slide open the battery compartment.

2 Insert two size AA batteries (supplied).Be sure to match the + and marks on thebatteries with the + and marks inside the batterycompartment.

Notes When the batteries become weak, the Function buttonindicators flash. If the remote control does not workproperly, the batteries may be weak.

When replacing batteries, replace both batteries with newones. Do not mix different types of batteries together.

When you remove the batteries, any manufacturer codesyouve set up may be erased. To set up the remote controlagain, see Setting Up the Remote Control on page 65.

v

v

v

v

v

v

v

Step 1: Inserting the BatteriesPage 7

Step 2: Connecting the Satellite Dish Antenna and Telephone Line

Page 8

Step 2: Connecting the Satellite Dish Antenna and Telephone Line

Page 8

Step 3: Connecting Your TVPage 9

Step 4: Adding a VCR and Audio System

(advanced connection) Page 10

Step 5: Connecting the VCR Controller


Step 6: Connecting the RF Antenna (SAT-A55 only)


Step 7: Connecting the AC Power Cord

Page 13

Step 8: Inserting the Access Card

Page 137

8

Step 2: Connecting the Satellite Dish Antenna and Telephone LineThe SATELLITE IN jack sends power to, and receives satellite signalsfrom, the Satellite Dish Antenna. The telephone line connectionperiodically sends information about your receiver and Access Card toyour service provider.

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN

VHF(SAT)/UHFOUT TEL LINE

AC IN~

1

2


Connect the SATELLITE IN jack to your Satellite Dish Antenna using RG-6 coaxial cable.

RG-6 Coaxial Cable from Satellite Dish Antenna

Telephone Cord

Connect the TEL LINE jack to a telephone line wall jack using the supplied telephone cord.

Notes The SAT-A55 model is shown.Connections for the SAT-B55model are the same.

Your Satellite Dish AntennaInstallation Instructionsprovides detailed instructionson how to install RG-6 coaxialcable from your Satellite DishAntenna.

CAUTIONOnly connect your authorizedSatellite Dish Antenna to theSATELLITE IN jack as describedin the Installation Instructions.Connecting any other equipmentto this jack could result in damageto the equipment and/or receiver.

11 2 2

Connecting

Your

Digital

SatelliteReceiver

Step 3: Connecting Your TVConnect your TV to the Digital Satellite Receiver as shown below. Referto your TVs instruction manual for more information.

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

VHF/UHF

VIDEO

L(MONO)

R

S VIDEO

IN

-AUDIO-

If you have a local TV antenna or cable company serviceConnect it to the VHF/UHF IN jack on your DigitalSatellite Receiver using a coaxial cable or RFadapter (not supplied).You can view local stations using your TV controls.

NoteYou must use the VHF(SAT)/UHF OUT jack toconnect to your TV orVCRwhen a local TV antennaor cable company service is connected to theVHF/UHF IN jack (see 2c below and on page 10).

If your TV has A/V input jacksConnect the VIDEO OUTjacks on your DigitalSatellite Receiver to theA/V input jacks on yourTVusing the supplied A/Vcable. (Be sure to match thecolors on the jacks with thecolored plugs on the A/Vcable.)

If your TV has an S-Video inputUse the S-Video cableinstead of the yellow videoconnection.If your TV has only oneaudio input, connect it tothe L(MONO) jack on thereceiver.

If your TV does not have A/V jacksConnect the VHF(SAT)/UHFOUT jack to the VHF/UHFinput jack on your TV usingcoaxial cable.Set the CH3/CH4 switch to thechannel that does not carry off-air broadcasts in your area.

NoteWith this connection, yourinput source is channel 3 orchannel 4 depending on howyou set the CH3/CH4 switchon the receiver.


Coaxial Cable

A/V CableVIDEO

(yellow) OR

S-Video

S-Video Cable

TVCoaxial Cable

1

1

2a

2a

2b

2b

2c

2c9

10

Step 4: Adding a VCR and Audio SystemYou can record programs by adding a VCR. You can also connect yourDigital Satellite Receiver to an audio system for enhanced soundenjoyment.

VHF/UHF

VIDEO

L(MONO)-AUDIO-R

S VIDEO

IN

VIDEO S VIDEOAUDIO

LINEIN

LINEOUT

IN

OUT

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

LINEIN

LINEOUT

AUDIO

OPTICALIN

If you have a digital or Dolby Digital audio system (SAT-A55 only)Connect theDIGITAL OUT(OPTICAL) of theDigital SatelliteReceiver to theoptical digitalinput of your audiosystem.

z TipIf you connect yourDigital SatelliteReceiver to a DolbyDigital receiver, setthe Dolby Digitaloption of theAudiodisplay to AutoSelect. See SettingAudio Options(AUDIO) on page64 for moreinformation.

Audio Receiver

If you have a stereo or Dolby Pro Logic audio systemConnect the upperAUDIO R and L(MONO)jacks on the DigitalSatellite Receiver to theaudio inputs of yourstereo amplifier.

If your TV and VCR have A/V jacksConnect the VIDEOOUT jacks ofyour Digital Satellite Receiver tothe A/V input jacks of your VCRusing the supplied A/V cable.Then, connect the A/V outputjacks of your VCR to the A/Vinput jacks of your TV using anA/V cable. (Be sure to match thecolors on the jacks with thecolored plugs on the A/V cable.)

If your TV and VCR have S-Video jacksUse the S-Video cable instead ofthe yellow video connection.

z TipTo allow your Digital SatelliteReceiver to control the recordingfunctions of your VCR, see Step5: Connecting the VCRController on page 11.

Stereo Cable

Optical Cable (SAT-A55 only)(optional Sonyaccessory POC-15A)


If your TV and VCR do not have A/V jacksConnect the VHF(SAT)/UHF OUT jack on theDigital Satellite Receiver tothe VHF/UHF input jackon your VCR using coaxialcable.Then, connect the VHF/UHF output jack on yourVCR to the VHF/UHFinput jack on your TVusingcoaxial cable.Set the CH3/CH4 switch tothe channel that does notcarry off-air broadcasts inyour area.

NoteWith this connection,your input source ischannel 3 or channel 4depending on how youset the CH3/CH4 switchon your VCR.

A/V Cable

VIDEO (yellow) OR S-Video

S-Video Cable Coaxial

Cable

TV

1a

1a1b

1b

2a

2a

2b

2b

2a 2b 2c

2c

VCR

2c

Connecting

Your

Digital

SatelliteReceiver

Step 5: Connecting the VCR ControllerConnect the VCR Controller to allow the Timer & Rec feature toautomatically operate your VCR.See Setting Up the VCR Control Feature on page 26 for informationabout setting up the Digital Satellite Receiver to work with your VCR.

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

1/2" to 1"

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

VIDEO S VIDEOAUDIO

LINEIN

LINEOUT

IN

OUT

CPD IN

To allow the Digital Satellite Receiver to control your VCRConnect theVCRControllerto the VCR CONTROL jackon the receiver.

If you are using a Sony SmartFile VCR to take advantage of the Program Data Download featureUse this connection instead of theVCR Controller connection. Forinformation about setting up theVCR Control feature, see page 26.For details about the Program DataDownload feature, refer to yourSmartFile VCR OperatingInstructions.


VCR ControllerCable VCR Controller

IR Sensor VCR (front view)

VCR (side view)

VCR Controller

Connecting a Sony SmartFile VCRDigital Satellite Receiver

Monaural Cable (supplied with SmartFile VCR)

Sony SmartFile VCR

In front of the VCRPlace theVCRController under and infront of the VCR.The VCR Controller must extend justin front of the infrared sensor of theVCR.

z TipIf the infrared sensor is not markedon your VCR, shine a flashlight intothe front panel of the VCR to locatethe sensor.

1b

1b

1a

1a11

12

Step 6: Connecting the RF Antenna (SAT-A55 only)With the SAT-A55 model you can connect the RF Antenna and operatethe Digital Satellite Receiver when installed in a cabinet or from anotherroom in your house using the remote control. See page 32 for informationabout how to set up the Digital Satellite Receiver to use the RF feature.

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

If you want to use the RF featureConnect the RF Antenna tothe RF REMOTE jack of theDigital Satellite Receiver.Then, place the RF Antennain a convenient location.

RF Antenna


Notes Do not place the RF Antennadirectly on top of the DigitalSatellite Receiver or any othermetal object. For best results,place the RFAntenna in a visiblelocation.

The operating range of theremote control is about 100 feetwhen using the RF feature. Thismay decrease due to ambientreception conditions, weakbatteries, etc.

1

1

Connecting

Your

Digital

SatelliteReceiver

Step 7: Connecting the AC Power CordAfter all other connections are complete, connect the AC Power Cord tothe Digital Satellite Receiver.

After you insert the Access Card and your Satellite Dish Antenna isinstalled, you are ready to begin enjoying digital satellite programming.Call DIRECTV at 1-800-DIRECTV (347-3288) to begin service.

ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2

AC Power Cord

to power outlet


ACCESS CARD

LOW SPEED DATA

VCR CONTROL

DIGITALOUT

(OPTICAL)

SATELLITE IN

RF REMOTE

R L(MONO)VIDEO OUT

AUDIO VIDEO

S VIDEO

CH3CH4

VHF/UHF IN


AC IN~

1

2


Access Card

Step 8: Inserting the Access Card13

14

Viewing Pictures From Your Digital Satellite Receiver

Using Your Remote ControlRM-Y802 Remote Control (SAT-A55 model)

NoteYou may need to set up the remote control to operate yourother audio/video equipment. See Setting Up the RemoteControl on page 65 for details.

1 MUTING buttonMutes the volume. Press again to restore thevolume. To operate your TV, you must first setup the remote control (see page 65).

2 AUDIO VOLUME buttonsAdjust the volume of your audio receiver. Tooperate your audio receiver, youmust first set upthe remote control (see page 65).

3 SLEEP buttonSets the TV to turn off automatically after acertain amount of time (if your TV has the Sleepfeature). To operate your TV, you must first setup the remote control (see page 65).

4 DISPLAY buttonOpens the program information display for thecurrent program.

5 ALT AUDIO buttonSwitches among the available audio broadcasts.

6 FAVORITE buttonOpens the Favorite Stations guide.

7 INDEX buttonOpens the Station Index.

8 VOL buttonsAdjust the volume. To operate your TV, youmust first set up the remote control (see page 65).

9 JoystickMoving the joystick up, down, left, right, anddiagonally moves the highlight in on-screendisplays. Press the joystick to select thehighlighted item.

q; CODE SET buttonLets you program the remote control to operateyour TV and other audio/video equipment (seepage 65).

SLEEP TV/SAT TV/VIDEO

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL

RM-Y802VTR3 2 DVD AMP

MENU

EXIT

CH

CATEGORY

CODE SET

+

2

8

3

4 5 6

9

FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

1

7

TV

0

MUTINGCABLE TV

POWER

1

2

3

4

5

6

8

9

0

7

qs

qd

qg

qh

qj

ql

w;

ws

qk

qf

qaSAT

wa

--POSITION

CH

SWAP PIP

+

TV SATCABLETV/VTRFUNCTION

--AUDIO OFF CH

+

POWER

MUTINGCABLE TV

POWER

wh

wj

wk

wd

wg

wf

SAT

View

ingPictures

FromYour

DigitalSatellite

Receiverqa POWER buttonsTurn on and off the Digital Satellite Receiver, TVand VTR (VCR). To operate your TV or VTR(VCR), you must first set up the remote control(see page 65).

qs FUNCTION buttonsSelect the equipment (CABLE, TV or SAT) thatyou want to operate. The indicators light up toshow which device the remote control isoperating. To operate your TV or cable box, youmust first set up the remote control (see page 65).

qd TV/VIDEO buttonSwitches between the various inputs of your TV.To operate your TV, you must first set up theremote control (see page 65).

qf TV/SAT buttonSwitches the output of your Digital SatelliteReceiver between regular TV and satellitebroadcasts. To receive regular TV broadcasts,you must have a local TV antenna or cablecompany connection (see page 9).

qg 09 and ENTER buttonsChange channels directly, and enter numericalvalues in on-screen displays.

qh JUMP buttonChanges channels to the previously tunedchannel.

qj GUIDE buttonOpens the Program Guide.

qk CATEGORY buttonOpens the Category Guide.

ql MENU buttonOpens the Main Menu.

w; CH buttonsChange channels. When a program guide isopen, pressing the CH buttons pages through theguide.

wa EXIT buttonCloses all on-screen displays including programguides and menus.

ws VTR3/2/DVD/AMP switchSets the remote to operate other devices in yourA/V system. To operate these other devices, youmust first set up the remote control (see page 65).

wd TV/VTR buttonSwitches between the TV and VTR (VCR) inputsof your TV. To operate your TV, you must firstset up the remote control (see page 65).

wf VCR Control buttonsOperate VCR features such as play, record,pause, stop, and fast wind. To operate your VCR,youmust first set up the remote control (see page65).

wg PIP control buttonsOperate the Picture-in-picture features of yourTV (if your TV has PIP). To operate your TV, youmust first set up the remote control (see page 65).

wh FUNCTION buttonsSelect the equipment (CABLE, TV or SAT) thatyou want to operate. The indicators light up toshow which device the remote control isoperating. To operate your TV or cable box, youmust first set up the remote control (see page 65).

wj POWER buttonTurns on or off the equipment selected with theVTR3/2/DVD/AMP switch.

wk CH +/ buttonsChange channels in numerical order on theequipment selected with the VTR3/2/DVD/AMP switch.15

16

Using Your Remote Control (continued)RM-Y139 Remote Control (SAT-B55 model)

NoteYou may need to set up the remote control to operate yourother audio/video equipment. See Setting Up the RemoteControl on page 65 for details.

1 MUTING buttonMutes the volume. Press again to restore thevolume. To operate your TV, you must first setup the remote control (see page 65).

2 TV/VIDEO buttonSwitches between the inputs of your TV. Tooperate your TV, youmust first set up the remotecontrol (see page 65).

3 TV/VTR buttonSwitches between the inputs of your VCR. Tooperate your VCR, you must first set up theremote control (see page 65).

4 TV/SAT buttonSwitches the output of your Digital SatelliteReceiver between regular TV and satellitebroadcasts. To receive regular TV broadcasts,you must have a local TV antenna or cablecompany connection (see page 9).

5 DISPLAY buttonOpens the program information display for thecurrent program.

6 INDEX buttonOpens the Station Index.

7 JUMP buttonChanges channels to the previously tunedchannel.

8 EXIT buttonCloses all on-screen displays including programguides and menus.

CHVOL

GUIDECATEGORYINDEX

ENTER

TV/VTR

FUNCTION

SATTVTV/VIDEO

DISPLAY

TVPOWER

PAGE

SAT

MUTINGVTR

VTR

TV/SAT

FAVORITEMENUJUMP EXIT

CODE SETRM-Y139

SATELLITERECEIVER

0

1 2

8

3

4 5 6

7 9

1

2

3

4

5

6

8

9

0

7

qs

qd

qf

qj

w;

qk

qa

qg

qh

ql

View

ingPictures

FromYour

DigitalSatellite

Receiver9 VOL buttonsAdjust the volume. To operate your TV, youmust first set up the remote control (see page 65).

q; CODE SET buttonLets you program the remote control to operateyour TV and other audio/video equipment (seepage 65).

qa POWER buttonsTurn on and off the Digital Satellite Receiver, TVand VTR (VCR). To operate your TV or VTR(VCR), you must first set up the remote control(see page 65).

qs FUNCTION buttonsSelect the equipment (SAT, TV, VTR) that youwant to operate. The indicators light up to showwhich device the remote control is operating. Tooperate your TV or VTR (VCR), youmust first setup the remote control (see page 65).

qd VCR Control buttonsOperate VCR features such as play, record,pause, stop, and fast wind. To operate your VTR(VCR), you must first set up the remote control(see page 65).

qf 09 and ENTER buttonsChange channels directly and enter numericalvalues in on-screen displays.

qg GUIDE buttonOpens the Program Guide.

qh CATEGORY buttonOpens the Category Guide.

qj Arrow and buttonsThe arrow buttons move the highlight inon-screen displays. The button selects thehighlighted item.

qk FAVORITE buttonOpens the Favorite Stations guide.

ql MENU buttonOpens the Main Menu.

w; CH/PAGE buttonsChange channels. When a program guide isopen, these buttons page through the guide.17

18

Selecting ItemsIn on-screen displays such as the Main Menu and program guides, youmust first move the highlight to the item you want, then select the item.

RM-Y802 Remote Control (SAT-A55 model)

RM-Y139 Remote Control (SAT-B55 model)

S

SATELLITERECEIVER

+

2

8

3

4 5 6

9

1

7

0

S

SATELLITERECEIVER

+

2

8

3

4 5 6

9

1

7

0

2 Press down on the joystick toselect the item.

1 Move the joystick in anydirection to move thehighlight to the item youwant.

0

1 2 34 5 6

87 9

SATELLITERECEIVER

0

1 2 34 5 6

87 9

SATELLITERECEIVER

1 Press the V/v/B/b buttonsto move the highlight to theitem you want.

2 Press the button toselect the item.

Note (SAT-B55 model)Whenever these Operating Instructionsrefer to using the joystick, use the arrowV/v/B/b buttons surrounding thebutton.

z TipBe sure to press the SAT FUNCTIONbutton before operating the DigitalSatellite Receiver with the remote control.

9

View

ingPictures

FromYour

DigitalSatellite

Receiver

Turning On the Power1

+

SATELLITERECEIVER

1 2

8

3

4 5 6

7 9


FUNCTIONTV SATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGTVCABLE

ALT AUDIO JUMP

CATEGORY GUIDEINDEXFAVORITE

MENU

EXIT

CHVOL

RM-Y802VTR3 2 DVD AMPCODE SET

0

POWER

SAT

z TipThe FUNCTION button indicators lightup to show you which equipment theremote control is operating.

NoteYou may need to set up the remotecontrol to operate your other audio/video equipment. See Setting Up theRemote Control on page 65 for details.

RM-Y802Remote Control

1 Press the POWER SAT button to turn on the Digital Satellite Receiver.The POWER indicator lights up.

2 Press the TV button to turn on the TV.

3 Press the TV FUNCTION button, then select the TVs input source to which you connected the Digital Satellite Receiver.Depending on how you connected your Digital Satellite Receiverto your TV, the input source could be channel 3 or channel 4, or youmay need to use the TV/VIDEO button to select one of the A/Vinput sources.

To make sure you are viewing satellite picturesPress the SAT FUNCTION button, then press theMENU button toopen the Main Menu.

If the MainMenu does not appear, turn off your equipment, checkyour connections and repeat from step 1.Press the EXIT button to close the Main Menu.

POWER

SAT

TV

FUNCTIONTV

3 4 TV/VIDEO/ /

FUNCTIONSAT

MENU

20

Changing Channels+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP


VOL


MENU

EXIT

CH

1

7

TV

TV

CODE SET

0

POWER

SAT

z TipYou can see information about aprogram you are watching by pressingthe DISPLAY button.


1 Press the SAT FUNCTION button.

12 Press the CH +/ buttons.The Digital Satellite Receiver tunes to the next channel, and theStation ID and channel number appear in the upper right corner ofyour TV screen.

You can also change channels by entering the three digit channelnumber using the 09 buttons, and either pressing the ENTERbutton or waiting several seconds.

The Digital Satellite Receiver tunes to that channel, and the StationID and channel number appear in the upper right corner of yourTV screen.

FUNCTIONSAT

CH

1 2 3ENTER

Using

theOn-Screen

Displays

Using the On-Screen Displays

Using the Main MenuThe Main Menu acts as a gateway to all of the features your DigitalSatellite Receiver has to offer.

Closing the Main Menu Highlight and select EXIT to close theMainMenu (the current programappears on your screen). You can also press the EXIT button on yourremote control.

The on-screen displays close automatically after several minutes.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

1 Press the MENU button.The Main Menu appears.

2 Highlight and select the feature you want to access.

MENU

SYSTEM (Page 22)Adjust and test your DigitalSatellite Receivers settings.AntennaVCR ControlSystem TestAspect RatioAccess CardRemote Control(SAT-A55 only)

GUIDES (Page 35)Access the many guides that help youfind the program you want.Alpha ListProgram GuideCategory GuideStation IndexFavorite StationsOther Guides

PREFERENCES (Page 46)Adjust the way menus andinformation appear.Display OptionsCustom StationsData Services(future application)

LOCKS & LIMITS (Page 53)Set limits on spending and ratings.Block stations and pay per viewprograms.

AUDIO (Page 64)Choose a preferred language for thedefault audio and current audio formultiple language programs.You can also select theDolbyDigitalsettings (SAT-A55 only).

TIMER & REC (Page 60)Schedule program tuning andrecording.

PURCHASES (Page 59)Review the pay per viewprogram purchases andcancellations you have made.

MESSAGES (Page 52)Read messages from yourservice provider.

RM-Y802Remote Control21

22

Setting Up Your Digital Satellite Receiver (SYSTEM)Using the System MenuThe System Menu provides many ways to adjust your Digital SatelliteReceiver so it matches your preferences and optimizes the conditions ofyour home entertainment system.

1 Press the MENU button, then highlight and select SYSTEM.The SYSTEM pop-up appears.

2 Highlight and select the item you want to set up.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET


MENU

ReturnCloses the SYSTEM pop-up toshow the Main Menu.

AntennaLets you find the position of thesatellite and helps you get thestrongest signal from yourSatellite Dish Antenna(see page 23).

VCR ControlLets you set up and test yourVCR using the VCR Controller(see page 26).

System TestLets you test the connectionsto your Satellite Dish Antenna,and telephone line(see page 29).

Aspect RatioLets you set the receivers output tomatch the aspect ratio of your TV(see page 30).

Access CardLets you initialize a replacementcard (see page 31).

Remote Control (SAT-A55 only)Lets you set up the receiver so theremote control can operate thereceiver from behind a cabinet orfrom another room (see page 32).

Using

theOn-Screen

DisplaysSetting Up the Satellite Dish AntennaThis display helps you aim your Satellite Dish Antenna to get thestrongest signal.For complete information on installation of your Satellite Dish Antenna,see the Satellite Dish Antenna Installation Instructions.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET 1 Press the MENU button, then highlight and select SYSTEM.The SYSTEM pop-up appears.

2 Highlight and select Antenna.The Antenna display appears.

MENU

NoteMost areas of the United States willnot receive a peak signal strength of100. Although there is no picturequality difference between a signalstrength of 60 and 100, a highersignal strength will limit anynegative effects in degraded

Antenna TypeSelect Round, Oval 2-Sat or Oval 3-Satdepending on your Satellite DishAntenna type.

TransponderLets you select the transponder fromwhich the Satellite Dish Antennareceives its signal.You do not need to change this settingunless instructed by your serviceprovider.

Antenna LocationLets you find out the direction of thesatellite from your location.

ReturnCloses the Antenna display toshow the Main Menu.

HelpOpens information about theAntenna display.

Signal Strength MeterShows the current and peaklevels of the signal strength.

Azimuth, Elevation and TiltShows how to aim your Satellite DishAntenna depending on your antennatype and location.

StatusLocked shows that your SatelliteDish Antenna is receiving a signal.Unlocked shows that a signal is notbeing received.

Signal SeekerWhen using a Round antenna,shows that your Satellite DishAntennas Signal Seeker can beused.

RM-Y802Remote Control23conditions such as rain or snow.

24

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)Selecting an Antenna TypeThe Antenna Type display lets you or your professional installer enterwhich type of Satellite Dish Antenna you use. After you have enteredyour antenna type, you can use the Antenna Location pop-up to help aimyour antenna

1 Highlight and select Antenna Type from the Antenna Display.The Antenna Type display appears.

2 Highlight and select the Satellite Dish Antenna type that you have installed.The Signal Seeker pop-up appears if you have selected Round.The Antenna Type display closes if you have selected Oval 2-Sator Oval 3-Sat.

3 Highlight and select On if you selected Round.The Signal Seeker pop-up closes to show the Antenna Display.z TipSelecting off in the Signal Seeker

pop-up may allow you to see theSignal Strength Meter if you use adiplexer or certain other accessorieswith your Satellite Dish Antenna.

NoteThe Signal Seeker feature is availableonlywith the RoundAntenna. See yourSatellite Dish Antenna InstallationInstructions for more informationabout this feature.

Using

theOn-Screen

DisplaysEntering Your Antenna LocationTheAntena Location pop-uphelps you or your professional installer aimyour Satellite Dish Antenna based on your zip code or your latitude andlongitude location.

1 Highlight and select Antenna Location from the Antenna display.The Antenna Location pop-up appears.

2 Select Zip Code.The Zip Code pop-up appears.

3 Enter your Zip Code, then select OK.If you have a Round Satellite Dish Antenna, you or yourprofessional installer can use the azimuth and elevation readingsto aim the antenna. If you have anOval 2-Sat orOval 3-Sat SatelliteDish Antenna, you or your professional installer can use theazimuth, elevation and tilt readings to aim the antenna.

z TipIf it is more convenient for you toenter latitude and longitude, selectLatitude & Longitude instead ofZip Code.

To change the number

To move to the next digit

OKCloses thepop-upandsaves your changes.

CancelCloses the pop-upwithout saving thechanges.

m

M

< ,

NoteRound Satellite Dish Antennas do nothave a Tilt setting.25

26

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)Setting Up the VCR Control FeatureThe VCR Control feature lets the Digital Satellite Receiver control yourVCR using the Timer & Rec feature (see page 60). To use the VCRControlfeature you must connect the VCR Controller or a Sony SmartFile VCR(see page 11).

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET


2 Highlight and select VCR Control.The VCR Control display appears.

MENU

ManufacturerLets you select themanufacturer code for yourVCR (see page 27).

Auto Title InsertLets you turn on the Auto TitleInsert feature (see page 28).

ReturnCloses the VCR Controldisplay to show the MainMenu.

HelpOpens information about theVCR Control display.


Using

theOn-Screen

DisplaysSetting the VCR Manufacturer CodeThe VCR Manufacturer Code allows the Digital Satellite Receiver tocontrol your VCR using the VCR Controller or a Sony SmartFile VCR.

1 Highlight and select Manufacturer from the VCR Control display (see page 26).The Manufacturer pop-up appears.

2 Highlight and select the manufacturer of your VCR.The manufacturers pop-up appears.

3 Select a VCR manufacturer code from the list.The Test pop-up appears.Some manufacturers have more than one code to choose from.If the VCR manufacturer code you select does not work in step 4below you can select another code for that manufacturer.

4 Select Yes to perform a VCR test.If you select Yes, a pop-up appears giving you instructions onhow to perform a VCR test.

If the test is unsuccessful, check your connections and the VCRController placement, then repeat this procedure selecting adifferent VCR manufacturer code in step 3 (if your VCRmanufacturer has more than one code).

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT


z TipIf you connected a Sony SmartFile VCR,use the manufacturer code of 99.

NoteDo not stop or interrupt the VCR test bypressing any buttons until after the VCRtest is complete.

continued27

28

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)Setting Up Auto Title InsertThe Auto Title Insert feature lets you display information about theprogram at the beginning of a Timer & Rec event. This is convenient ifyou want a title to appear at the beginning of programs you scheduleor record.

1 Highlight and select Auto Title Insert from the VCR Control display (see page 26).The Auto Title Insert pop-up appears.

2 Select On or Off.The Auto Title Insert pop-up closes to show the VCR Controldisplay.

When the scheduled event beginsA title appears at the beginning of any Timer & Rec event.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

Note


Program description

RatingDate

Program name ChannelNetwork

Program lengthWhen you schedule two or moreconsecutive programs, the Auto TitleInsert feature will only appear before thefirst program.

Using

theOn-Screen

DisplaysPerforming a System TestThe system test checks your Access Card, telephone line, and SatelliteDish Antenna connections for proper operation.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT


2 Highlight and select System Test.The System Test display appears.

3 Highlight and select Test.The system test begins.If the system test fails, check your connections before calling yourservice provider or Sony.

4 Select Return.The System Test display closes to show the Main Menu.

MENU

ReturnCloses the System Testdisplay to show theMain Menu.

TestStarts the system test.

HelpOpens informationabout the System Testdisplay.

continued


30

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)Setting the Aspect RatioThe aspect ratio refers to the proportion of your TV screen. Some newerTVsmay offer the 16:9 ratiowhich is similar to the proportions of amoviescreen. Most TVs use the standard 4:3 ratio.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

NoteTo use the Wide aspect ratio feature, youmust receive a 16:9 aspect ratio signal.Checkwith your service provider to see if16:9 programming is available.



2 Highlight and select Aspect Ratio.The Aspect Ratio display appears.

3 Highlight and select the aspect ratio of your TV.The highlight moves to Return.

4 Select Return.The Aspect Ratio display closes to show the Main Menu.

MENU

ReturnCloses the Aspect Ratiodisplay to show theMain Menu.

HelpOpens informationabout the Aspect Ratiodisplay.

Using

theOn-Screen

DisplaysReplacing Your Access CardOccasionally your service provider may send you a new Access Card.Use this display to set up your new card. See Inserting the Access Cardon page 13 for information about inserting the Access Card into theDigital Satellite Receiver.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT


2 Highlight and select Access Card from the System pop-up.The Access Card display appears.

3 Highlight and select OK.The display shows instructions on how to proceed.

4 Follow the instructions in each display to complete the replacement process.

MENU

ReturnCloses the Access Carddisplay to show theMainMenu.

OKStarts the Access Cardreplacement process.

HelpOpens informationabout the Access Carddisplay.

continued


32

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)Selecting RF or IR Remote Control Reception (SAT-A55 only)The RF feature allows you to operate the Digital Satellite Receiver fromoutside a cabinet or from another room within your home. The RFAntenna must be connected to use the RF feature (see page 12).

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET 1 Press the MENU button, then highlight and select SYSTEM.The SYSTEM pop-up appears.

2 Highlight and select Remote Control.The Remote Control display appears.

MENU

Remote SignalLets you select IR or RF as the typeof signal the receiver accepts.

RF Security ControlLets you change the security code.RF signals are used to controlmany devices. You may need tochange the security code so thatthis remote control operates theDigital Satellite Receiver only.

ReturnCloses the Remote Controldisplay to show the Main Menu.

HelpOpens information about theRemote Control display.

3 Highlight and select Remote Signal.The Remote Signal pop-up appears.


Using

theOn-Screen

DisplaysSetting the Security CodeIf the Digital Satellite Receiver is receiving signals from another RFremote control in your home (or from your neighbors home), you caneliminate this problem by changing the security codes for the DigitalSatellite Receiver and remote control, or by selecting IR control.Both the Digital Satellite Receiver and the remote control must use thesame three digit security code.

1 Select Remote Control from the SYSTEM pop-up (see page 32).The Remote Control display appears.

2 Highlight and select RF Security Code.The confirmation pop-up appears.

4 Highlight and select RF.The Remote Signal pop-up closes to show the Remote Controldisplay.

5 Highlight and select Return.The display closes to show theMainMenu, and theDigital SatelliteReceiver is set to receive RF signals from the remote control.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

MENU

continuedRM-Y802Remote Control33

34

Setting Up Your Digital Satellite Receiver (SYSTEM) (continued)3 Select Yes.The RF Security Code pop-up appears.

4 Select a different security code.The conformation pop-up appears.

5 Press the CODE SET button on the remote control.The CABLE and TV FUNCTION indicators flash.

6 Enter the three digit security code you selected for the receiver in step 4 above.

7 Press the enter button.The remote control and Digital Satellite Receiver are now set to anew security code.

8 Select OK to save your changes.The Remote Control display appears.Note

If the remote control no longer operatesyour Digital Satellite Receiver aftercompleting this procedure, use thecontrols on the front panel to open theRemote Control display (see page 32).Then repeat the steps in Setting theSecurity Code to try again.

CODE SET

FUNCTIONSATCABLE TV

ENTER

Using

theOn-Screen

Displays

Viewing Station and Program Information (GUIDES)Using the Guides MenuThe Guides Menu helps you find the program you want to watch. Youcan choose to see all stations or just a few. You can also create your ownfavorite station guides for fast access to your favorite stations.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

1 Press the MENU button, then highlight and select GUIDES.The GUIDES Menu appears.

2 Highlight and select the guide you want to use.

MENU

ReturnCloses the GUIDES Menu toshow the Main Menu.

Alpha ListShows a list of categories(movies, sports, etc.) andonly the programs that matchthe category you select inalphabetical order (see page 36).

Program GuideOpens your custom list ofstations and shows programinformation for up to three daysin advance (see page 37).

Category GuideShows a list of categories(movies, sports, etc.) and onlythose stations broadcastingprograms that match thecategory you select(see page 38).

z Tips Be sure to press the SATFUNCTION button beforeoperating the DigitalSatellite Receiver with theremote control.

You can see informationabout a program you arewatching by pressing theDISPLAY button.

Station IndexOpens your custom list ofstations as a grid of station logos(see page 39).

Favorite StationsOpens the Favorite Stationsguide which allows you to createand access up to four differentsets of stations you enjoywatching most (see page 40).

Other GuidesOpens the Other Guides displaywhich shows a variety of specialcategories provided byDIRECTV. Each category isdivided into subcategories so youcan find exactly the kind ofprogram you want (see page 43).

continued


36

Viewing Station and Program Information (GUIDES) (continued)Using the Alpha ListThe Alpha List shows program information in the category you select(such as movies, sports, etc.) in alphabetical order. Program informationis available for up to four hours in advance.

1 Press the MENU button, then highlight and select GUIDES.The GUIDES Menu appears.

2 Highlight and select Alpha List.The Alpha List guide appears.

3 Highlight and select a category.Programs appear in alphabetical order.

4 Highlight and select a program.If you select a current program, the Alpha List guide closes. Forinformation about selecting a future program see Using OneButton Timer & Rec on page 60.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

MENU


Using

theOn-Screen

DisplaysUsing the Program GuideThe Program Guide shows program information for up to three days inadvance. You can open the Program Guide using the Main Menu or bypressing the GUIDE button.

SATELLITERECEIVER

ALT AUDIO JUMP


VOL


MENU

EXIT

CH

CODE SET

M

m


1 Press the GUIDE button.The ProgramGuide opens and the current program appears in theMedia Window.

2 Highlight the program you want. The sound and the picture in the Media Window change as youhighlight different programs.Skipped stations do not appear (see page 50).

GUIDE

Media WindowInformation Area

Move the joystick upand down to highlightdifferent stations.

Press the CH V/vbuttons to move thehighlight to the nextpage of stations.

List Area

< ,Move the joystick right tohighlight future programs.

3 Select the program you want.If you select a current program, the Program Guide closes. Forinformation about selecting a future program, see One ButtonTimer & Rec on page 60.

z TipPress the EXIT button to close theProgram Guide and return to theprevious station.

NoteIf you select a program and the station isblocked or a limit has been reached, youcan temporarily unlock your DigitalSatellite Receiver using your passcode.See Locking Your Receiver on page 57for information about the passcode.

continued37

38

Viewing Station and Program Information (GUIDES) (continued)Using the Category GuideThe Category Guide shows programs in the category you select (such asmovies, sports, etc.). Program information is available for up to threedays in advance. You can open the Category Guide using theMainMenuor by pressing the CATEGORY button.

1 Press the CATEGORY button.The CategoryGuide opens and the current program appears in theMedia Window.

2 Highlight and select the category you want.The program list changes each time you select a different category.Skipped stations do not appear (see page 50).

3 Highlight and select the program you want.If you select a current program, the Program Guide closes. Forinformation about selecting a future program, see One ButtonTimer & Rec on page 60.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

CATEGORY

z TipPress the EXIT button to close theCategory Guide and return to theprevious station.


Using

theOn-Screen

DisplaysUsing the Station IndexThe Station Index displays each stations logo and channel number in agrid format. Program information is available for the current time only.You can open the Station Index using the Main Menu or by pressing theINDEX button.

1 Press the INDEX button.The Station Index opens and the current program appears in theMedia Window.

2 Highlight the station you want.The sound and the picture in the Media Window change as youhighlight different stations.Skipped stations do not appear (see page 50).

3 Select the station you want.The Station Index closes and the program broadcast by the stationyou selected appears on your TV screen.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

INDEX

z Tips Press the EXIT button to close theStation Index and return to theprevious station.

To view the current program whilechecking the program information ofother stations, turn on the Surf feature(see page 49).

continued


40

Viewing Station and Program Information (GUIDES) (continued)Using the Favorite Stations GuideThe Favorite Stations guide shows four Favorite Titles that you cancustomize with eight stations each. Program information is available forthe current time only.You can open the Favorite Stations guide using the Main Menu or bypressing the FAVORITE button.Before you can use the Favorite Stations guide, you must set up yourfavorite stations in a personal guide by following the procedure on thenext page.

1 Press the FAVORITE button.The Favorite Stations guide opens and the current programappears in the Media Window.

2 Highlight and select the Favorite Title you want.The station list in the right half of the display changes as youhighlight different Favorite Titles.

3 Highlight and select the station you want.The Favorite Stations guide closes and the program broadcast bythe station you selected appears.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

FAVORITE

z TipPress the EXIT button to close theFavorite Stations guide and return to theprevious station.


Using

theOn-Screen

DisplaysCustomizing the Favorite Stations Guide

1 Highlight and select the Favorite Title you want to customize.The station list appears in the right half of the display.

2 Highlight and select Edit.The Edit pop-up appears.

3 Highlight and select Edit Stations.The station index appears in the right half of the display.

4 Highlight and select a station in the index.A checkmark appears in the lower left part of the icon to indicatethat the station is included in the Favorite Title, and the number inthe Count box increases by one.

5 Repeat step 4 to add up to eight stations to this Favorite Title.When you have added all the stations you want in this FavoriteTitle, highlight and select OK.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

z TipPress the EXIT button to close theFavorite Stations guide and return to theprevious station.

NoteThe Count box indicates how manystations are included in the personalguide.

continued


42

Viewing Station and Program Information (GUIDES) (continued)Editing the Title of a Favorite Title

1 Highlight and select the Favorite Title you want to edit.The station list appears in the right half of the display.

2 Highlight and select Edit.The Edit pop-up appears.

3 Select Edit Title from the pop-up menu.The Edit Title display appears in the lower left part of the display.

4 Enter a seven character title for this Favorite Title.You can enter upper and lower case letters, numbers, and symbolsin the title.

5 When your title is complete, highlight and select OK.The Edit Title pop-up closes to show the Favorite Stations guide.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

z TipPress the EXIT button to close theFavorite Stations guide and return to theprevious program.

F a v 1Move the joystick up anddown to select differentcharacters.

Move the joystick left or right tohighlight different positions. You canalso press to move to the nextposition.

m

M

< ,


Using

theOn-Screen

DisplaysUsing Other GuidesThe Other Guides display provides special categories supplied byDIRECTV. Each category is divided into subcategories to help you findthe exact program you want to watch. Program information is availablefor up to three days in advance.

1 Press the MENU button, then highlight and select GUIDES.The GUIDES pop-up appears.

2 Highlight and select Other Guides.The Other Guides display appears.

3 Select the Guide Type you want.The available time ranges appear.

4 Select the time range you want.The available categories appear.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

MENU

z TipPress the EXIT button to close the OtherGuides display and return to theprevious station.

NoteDIRECTV occasionally changes thecontents of the category and subcategorylists.

continued


44

Viewing Station and Program Information (GUIDES) (continued)5 Select the category you want.If the category you select has subcategories, the availablesubcategories appear.

6 Select the subcategory you want.The programs that match your selections appear in the lower halfof the display.

7 Highlight and select the program you want.If you select a current program, the Other Guides display closes.For information about selecting a future program, see One ButtonTimer & Rec on page 60.

45

Using

theOn-Screen

Displays

Viewing Pay Per View ProgramsManyprograms are available as pay per view. By selecting a pay per viewprogram you agree to be charged for that program.

Select a pay per view program using any of the methods described in the Viewing Station and Program Information (GUIDES) section on pages 35 through 44.The Purchase Program display appears. This display showsdetailed information about the program including the cost.

ReturnCloses the Purchase Programdisplay to show the previousscreen.

PurchaseOpens the Purchase pop-up.

PreviewCloses the Purchase Programdisplay to show a preview of theprogram if available.

TimesOpens the Other Show Timesdisplay so you can select anothertime to view the program.

HelpOpens information about thePurchase Program display.

NoteTo order pay per view by remote, aDIRECTV subscription is required andthe Digital Satellite Receiver must becontinuously connected to a land-basedphone line.

46

Adjusting the Displays (PREFERENCES)Using the Preferences MenuThe Preferences Menu lets you change the appearance of theon-screen displays, the stations you want to appear in the program listarea, and the order in which the stations are listed.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

1 Press the MENU button, then highlight and select PREFERENCES.The PREFERENCES Menu appears.

2 Highlight and select the item you want to adjust.

MENU

ReturnCloses the PREFERENCES Menu toshow the Main Menu.

Display OptionsLets you change the color scheme ofthe on-screen displays, choose howthe stations are ordered in the guidesand select what is displayed in theMedia Window when surfingthrough the Station Index(see page 47).

Custom StationsLets you customize whichstations appear in the programguides (see page 50).

Data ServiceA future application(see page 51).


Using

theOn-Screen

DisplaysSetting Display OptionsDisplay Options lets you choose the color scheme of the on-screendisplays and the order in which stations are listed in the program listarea. You can also turn the surf option on or off.


2 Highlight and select Display Options.The Display Options display appears.SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

MENU

ReturnCloses the Display Options displayto show the Main Menu.

HelpOpens information about theDisplay Options display.

ColorsLets you change the color of the on-screen displays (see page 48).

Station orderLets you select the order in whichstations appear in the list area(see page 49).

SurfLets you view the Current Programin the Station Index while viewother Program information(see page 49).

continued


48

Adjusting the Displays (PREFERENCES) (continued)Changing the Color Scheme

1 Highlight and select Colors from the Display Options display (see page 47).The Colors pop-up appears.

2 Highlight and select the color scheme you like.The display changes colors as you highlight each color scheme.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT


Using

theOn-Screen

DisplaysChanging the Station OrderYou can select numerical or alphabetical for the order in which stationsappear in the List Area of the ProgramGuide, Category Guide and OtherGuides display.

1 Highlight and select Station Order from the Display Options display (see page 47).The Station Order pop-up appears.

2 Highlight and select the order you like.The Station Order pop-up closes to show the Display Optionsdisplay.

Changing the Surf SettingWhen the Surf setting is On you can view the current program in theMedia Window of the Station Index while viewing the programinformation of other programs as you highlight them in the Station Index.

1 Highlight and select Surf from the Display Options display (see page 47).The Surf pop-up appears.

2 Highlight and select On or Off.The Surf pop-up closes to show the Display Options display.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

continued


50

Adjusting the Displays (PREFERENCES) (continued)Setting Up Custom StationsThe Custom Stations display lets you choose which stations will beskipped in the Program Guide, Category Guide and Station Index, andwhen you change channels using the CH +/ buttons.You can reduce the number of stations that appear by skipping unwantedstations.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET


2 Highlight and select Custom Stations.The Custom Stations display appears.

MENU

ReturnCloses the Custom Stations display toshow the Main Menu.

CancelCloses the Custom Stations displayand cancels your changes.

AutoScans all stations and automaticallyskips any stations to which you do notsubscribe.

Clear AllRemoves all skip settings.

HelpOpens information about the CustomStations display.

X Skip MarkShows that the station will be skippedwhen using the Program Guide,Category Guide, Station Index, orwhen using the CH +/ buttons.


Using

theOn-Screen

DisplaysSelecting Data ServicesThe Data Services feature is reserved for future applications.

3 Highlight and select a station icon to add or remove the X mark.The x mark indicates that the station will be skipped when youopen the Program Guide, Category Guide or Station Index, orchange channels using the CH +/ buttons.

4 Highlight and select Return.The Custom Stations display closes to show the Main Menu.51

52

Your service provider may occasionally send messages to your DigitalSatellite Receiver to inform you of changes to your service and otherspecial announcements.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

NoteYour receiver can hold a total of between10 and 20 new and old messages,depending on the size of the messages.Your receiver will continue to hold amessage until you delete it or until the ACPower Cord is disconnected. If yourreceiversmemory is full, youmust deleteold messages before you can receive newones.


1 Press the MENU button, then highlight and select MESSAGES.The Messages display appears.

2 Highlight and select the message you want to read.The message pop-up appears.

MENU

ReturnCloses the Messages display toshow the Main Menu.

HelpOpens information about theMessages display.

DeleteCloses the message pop-up anddeletes the message.

ReturnCloses the message pop-up andsaves the message.

3 Highlight and select Return or Delete.The message pop-up closes to show the Messages display.

Viewing Messages (MESSAGES)

Using

theOn-Screen

Displays

Setting Locks and Limits (LOCKS & LIMITS)Using the Locks & Limits DisplayThe Locks & Limits feature gives you control over access to your DigitalSatellite Receiver. You can restrict program viewing by cost, ratings, andstation. You can also set a lock to prevent the ordering of pay per viewprograms.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

NoteYou must lock the receiver before anylocks or limits take effect (see page 57).

1 Press the MENU button, then highlight and select LOCKS & LIMITS.The Locks & Limits display appears.

2 Highlight and select Edit.The Locks & Limits edit display appears.The following pages describe how to change the settings for eachof these items.

MENU

Spending LimitSets a maximum limit on chargesper event (see page 54).

Rating LimitSets a maximum limit on ratedcontent (see page 55).

Pay Per ViewBlocks access to pay per viewprograms (see page 55).

Stations BlockedBlocks access to specific stations(see page 56).

LockOpens the passcode pop-up. Youmust enter your passcode to lock thereceiver.

UnlockOpens the passcode pop-up forunlocking your receiver.

Receiver StatusShows if your Digital SatelliteReceiver is now locked or unlocked.

continued


54

Setting Locks and Limits (LOCKS & LIMITS) (continued)Changing the Spending LimitThe spending limit pop-up lets you limit the amount you can spend perevent on pay per view purchases.

1 Highlight and select Spending Limit from the Locks & Limits edit display (see page 53).The Spending Limit pop-up appears.

2 Press the 09 buttons to enter the dollar value.You can enter a value of less than $656.

3 Highlight and select OK.The Spending Limit pop-up closes to show the Locks & Limits editdisplay.Select Cancel to close the Spending Limit pop-upwithout savingchanges.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

6 5 5


Using

theOn-Screen

DisplaysChanging the Rating LimitThe Rating Limit pop-up lets you limit programs according to the contentrating.

1 Highlight and select Rating Limit from the Locks & Limits edit display (see page 53).The Rating Limit pop-up appears.

2 Highlight and select the highest content rating you want your Digital Satellite Receiver to access.The Rating Limit pop-up closes to show the Locks & Limits editdisplay.

Changing the Pay Per View Access SettingThe pay per view access setting lets you block access to pay per viewstations.

1 Highlight and select Pay Per View from the Locks & Limits edit display (see page 53).The Pay Per View Access pop-up appears.

2 Select Yes to block access to pay per view programs.Select No to allow access to pay per view programs.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

continued


56

Setting Locks and Limits (LOCKS & LIMITS) (continued)Changing the Stations Blocked SettingsThe Stations Blocked feature lets you block access to specific stations.

1 Highlight and select Stations Blocked from the Locks & Limits edit display (see page 53).The Stations Blocked display appears.

2 Highlight and select a station icon to block that station.The block symbol appears in the station icon to indicate that thestation is blocked.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

ReturnCloses the Station Blockeddisplay.

CancelCloses the Stations Blockeddisplay without saving yourchanges.

Clear AllUnblocks all stations.

HelpOpens the help display.

Block IconShows that this station willbe blocked.

Block AllBlocks all stations.


Using

theOn-Screen

DisplaysLocking Your ReceiverAfter you have made the changes you want to the Locks & Limitssettings, you must enter a passcode to lock the receiver.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

z TipDo not forget your passcode.Youwill need this number to unlock yoursystem or make any changes to the locksor limits you have set. If you forget yourpasscode, contact your program providerfor assistance.



2 Highlight and select Edit, then select Lock.The Lock Receiver pop-up appears.

3 Enter a four digit passcode using the 09 buttons.Each number you enter appears as an asterisk (*) which keeps yourpasscode secret.

4 Enter your passcode again.This confirms your selection of a passcode number.

5 Highlight and select Return.The Main Menu appears.Your receiver is now locked with your passcode using the locksand limits you have set.

MENU

1 2 3 4

continued57

58

Setting Locks and Limits (LOCKS & LIMITS) (continued)Unlocking Your ReceiverIf you want to make changes to the Locks & Limits settings, you mustenter your passcode to unlock the receiver.

+

SATELLITERECEIVER

2

8

3

4 5 6

9


FUNCTIONSATCABLE

AUDIOVOLUME

ENTERDISPLAY

MUTINGCABLE

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

1

7

TV

TV

CATEGORY

CODE SET

0

POWER

SAT

z TipYou can temporarily unlock your DigitalSatellite Receiver with your passcode ifyou select a program from a guide and thestation is locked or a limit has beenreached.



2 Highlight and select Edit.The Unlock Receiver pop-up appears.

3 Enter your four digit passcode using the 09 button.Each number you enter appears as an asterisk (*) which keeps yourpasscode secret.The Locks & Limits edit display appears.

4 Highlight and select Unlock.Your receiver is now unlocked.

5 Highlight and select Return.The Main Menu appears.

MENU

1 2 3 4

59

Using

theOn-Screen

Displays

Checking Your PurchasesYou can view a history of the pay per view purchases you have made.This display also shows the future purchases you have ordered and thosethat you have canceled.

SATELLITERECEIVER

ALT AUDIO JUMP

GUIDEINDEXFAVORITE

VOL


MENU

EXIT

CH

CATEGORY

CODE SET

1 Press the MENU button, then highlight and select PURCHASES.The Purchases display appears.

2 Highlight and select the purchase number you want to view.The information pop-up for that purchase appears.

MENU

ReturnCloses the Purchases display toshow the Main Menu.

HelpOpens information about thePurchases display.

Cancel PPVCancels the Pay Per Viewprogram.

OKCloses the information pop-up toshow the Purchases display.

3 Highlight and select OK.The information pop-up closes to show the Purchases display.z TipYou can purchase pay per viewprogramsfrom any guide. See Viewing Pay PerView Programs on page 45.

Checking Pay Per View Purchases (PURCHASES)


60

Scheduling Programs (TIMER & REC)Using One Button Timer & RecYou can easily set the timer to view or record programs by selectingfuture programs directly from program guides.To record a future program use the VCR Control feature to turn on yourVCR and start recording automatically. For information on how to set upthe VCR Control feature, see page 26.

Highlight and select a future program using any of the methods described in Viewing Station and Program Information (GUIDES) on pages 35 through 44.

ReturnCloses the futureprogram pop-up to showthe current guide.

Tune to StationCloses theprogramguideto show the currentprogram of the selectedstation.

Add to Timer & RecAdds the program to theTimer & Rec display forrecording, and opens theschedule pop-up.

Add to TimerAdds the program to theTimer & Rec display fortuning, and opens theschedule pop-up.

OnceAdds the program to theTimer & Rec display for onetime tuning and/or recording.

MondayFridayAdds the program to theTimer & Rec display for theremaining week days of thecurrent week for tuning and/or recording.

WeeklyAdds the program to theTimer & Rec display fortuning and/or recording onthe same day of the followingfour weeks.

DailyAdds the program to theTimer & Rec display fortuning and/or recordingevery day for the next 30 days.

z Tips You can set up the Digital Satellite Receiver to sendprogram information to your VCR so it records theinformation at the beginning of the recording. Seepage 28 for information.

Your Digital Satellite Receiver has a Program DataDownload feature and will automatically send thefollowing informationwhen you record a programwith a Sony SmartFile VCR: program title,program category, program date/time andduration.For further information regarding the SmartFilefunction, refer to your Sony SmartFile VCROperating Instructions.

Notes When using the VCR Control feature to record afuture program, make sure that the VCR is turnedoff before the program begins. The VCR Controlfeature will turn on your VCR and

Date post:	19-Nov-2015
Category:	Documents
Upload:	k6may
View:	229 times
Download:	3 times

Sony A 55 Manual 081800 Manual

Documents