Flash:Flash range (ISO sensitivity (Recommended exposure Index) set to Auto): approx. 0.2 to 3.3 m (7 7/8 inches to 10 feet 10 inches) (W)/approx. 0.4 to 1.8 m (1 feet 3 3/4 inches to 5 feet 10 7/8 inches) (T)
[Input and Output connectors]Multi connector Video output
Audio output (Monaural)USB communication
USB communication: Hi-Speed USB (USB 2.0 compliant)
[LCD screen]LCD panel: 6.2 cm (2.5 type) TFT driveTotal number of dots: 115 200 (480 × 240) dots
[Power, general]Power: Rechargeable battery pack NP-BG1, 3.6 V
AC-LS5K AC Adaptor (not supplied), 4.2 VPower consumption (during shooting with the
LCD screen on):1.1 W
Operating temperature: 0 to 40°C (32 to 104°F)Storage temperature: –20 to +60°C (–4 to +140°F)Dimensions: 91.0 × 58.0 × 22.9 mm (3 5/8 ×
CND, AEP, UK, E,E, AUS, HK, CH, UK, E, AUS, HK, UK, E, AUS, HK, UK, E, AUS, HK,
AUS, KRKR, AR, BR, J, JE CH, KR, JE CH, KR, J, JE CH, KR, J, JE
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. FLEXIBLE Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°Cduring repairing.
• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
• Be careful not to apply force on the conductor when solderingor unsoldering.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
Model information table
• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European model
— 4 —DSC-W80/W85_L2
TABLE OF CONTENTS
1. SERVICE NOTE1-1. Precaution on Replacing the SY-173 Board ···················· 1-11-2. Self-diagnosis Function ··················································· 1-11-3. Process After Fixing Flash Error ····································· 1-21-4. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-31-5. How to Write Data to Internal Memory ·························· 1-4
2. DISASSEMBLY2-1. Identifying Parts ······························································ 2-22-2. Disassembly ····································································· 2-32-3. Exchange method of barrier block ·································· 2-62-4. Exchange method of zoom gear block ···························· 2-8
5. REPAIR PARTS LIST5-1. Exploded Views ······························································· 5-25-2. Electrical Parts List ························································· 5-7
Section Title Page
1-1
ENGLISH JAPANESEENGLISH JAPANESE
DSC-W80/W85_L2
1. SERVICE NOTE
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis FunctionWhen problems occur while the unit is operating, the self-diagnosisfunction starts working, and displays on the LCD screen what todo.Details of the self-diagnosis functions are provided in the Instructionmanual.
1-2-2. Self-diagnosis DisplayWhen problems occur while the unit is operating, the LCD screenshows a 4-digit display consisting of an alphabet and numbers, whichblinks at 3.2 Hz. This 5-character display indicates the “repairedby:”, “block” in which the problem occurred, and “detailed code”of the problem.
0 03 2C
Repaired by:
Refer to “1-2-3. Self-diagnosis Code Table”.Indicates the appropriatestep to be taken.E.g.13 ....Format the “Memory Stick Duo”.32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2 Hz
C : Corrected by customerE : Corrected by service
engineer
LCD screen
1-1. PRECAUTION ON REPLACING THE SY-173 BOARD
DESTINATION DATAWhen you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.The set is shipped with a unique ID (USB Serial No.) written in it.This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-2
ENGLISH JAPANESEENGLISH JAPANESE
DSC-W80/W85_L2
1-3. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flashis changed automatically to disabling charge and flash setting.After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
1-2-3. Self-diagnosis Code Table
C
C
E
E
E
E
E
E
E
E
E
BlockFunction
1 3
3 2
6 1
6 1
6 2
6 2
6 2
6 2
6 2
9 1
9 2
DetailedCode
0 1
0 1
0 0
1 0
0 2
1 0
1 1
1 2
2 0
0 1
0 0
Symptom/State
The internal memory has experienced aformat error.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” type error
The camera cannot read or write dataon the “Memory Stick Duo”.
Trouble with hardware
Difficult to adjust focus(Cannot initialize focus)
Turn the power off and on again, or taking out and inserting the“Memory Stick Duo” several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does notrecover, check the focus reset sensor of lens block (pin ws ofCN402 on the SY-173 board). If it is OK, check the focus motordrive IC (IC401 on the SY-173 board).
Retry turn the power on by the power switch. Check the zoomreset sensor of lens block (pin ra of CN402 on the SY-173board), if zooming is performed when the zoom button isoperated. If it is OK, check the zoom motor drive IC (IC401 onthe SY-173 board).
Check or replacement of the IC for steadyshot (IC503 on the SY-173 board).
Check or replacement of the IC for steadyshot (IC503 on the SY-173 board).
Check the HALL element (PITCH) of optical image stabilizer(pin 5, 6 of CN402 on the SY-173 board). If it is OK, checkPITCH angular velocity sensor (SE502 on the SY-173 board)peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pinql, w; of CN402 on the SY-173 board). If it is OK, check YAWangular velocity sensor (SE501 on the SY-173 board) peripheralcircuits.
Check the OIS temp sensor of optical image stabilizer (pin 4 ofCN402 on the SY-173 board).
Checking of flash unit or replacement of flash unit. (Note)
Use the compatible battery only.
Note: After repair, be sure to perform “1-3. PROCESS AFTER FIXING FLASH ERROR”.
Initializes the setting to the default setting. Even if you execute this function, the images stored in the internal memory are retained.
1 Select [Initialize] with v/V/b/B, then press z.The message “Initialize all settings” appears.
2 Select [OK] with v, then press z.The settings are reset to the default setting.
To cancel the resettingSelect [Cancel] in step 2, then press z.
• Make sure that the power is not disconnected during resetting.
Initialize
1-3
ENGLISH JAPANESEENGLISH JAPANESE
DSC-W80/W85_L2
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the SY-173 board, erase the data in internal memory of the board before replacement.Note 2: When replacing the SY-173 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having 32 MB or larger capacity.
2 Select [Copy] with v/V/b/B on the control button, then press z.The message “All data in internal memory will be copied” appears.
3 Select [OK] with v, then press z.Copying starts.
To cancel the copyingSelect [Cancel] in step 3, then press z.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot copy individual images.• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in [Internal Memory Tool].
• When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied. You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be copied.
• Even if you copy data, a (Print order) mark is not copied.
Copy
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
Formats the internal memory.• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V/b/B on the control button, then press z.The message “All data in internal memory will be erased” appears.
2 Select [OK] with v, then press z.The format is completed.
To cancel the formattingSelect [Cancel] in step 2, then press z.
Format
1-4
ENGLISH JAPANESEENGLISH JAPANESE
DSC-W80/W85_L2
1-5. HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.To change the setting, use the write enable tool “WriteEnableTool.exe”.
Data writing method1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”.2) Start the Write Enable Tool and the SeusEX.3) Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).6) Write the data read out into the PC to the internal memory of the camera.7) Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
1-5
ENGLISH JAPANESEENGLISH JAPANESE
DSC-W80/W85_L2
1. SERVICE NOTE
1-1. SY-173基板交換時の注意
仕向けデータ補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-2. 自己診断機能1-2-1. 自己診断機能について本機の動作に不具合が生じたとき，自己診断機能が働き，L C D 画面に，どう処置したらよいか判断できる表示を行います。自己診断機能については取扱説明書にも掲載されています。
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt which comes off at the point.(Be careful or some pieces of gilt may be left inside)
DISCHARGING OF THE ST-160 BOARD’S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of the ST-160 board is chargedup to the maximum 300 V potential.There is a danger of electric shock by this high voltage when thecapacitor is handled by hand. The electric shock is caused bythe charged voltage which is kept without discharging when themain power of the unit is simply turned off. Therefore, theremaining voltage must be discharged as described below.
Preparing the Short JigTo preparing the short jig, a small clip is attached to each end ofa resistor of 1 kΩ /1 W (1-215-869-11).Wrap insulating tape fully around the leads of the resistor toprevent electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the CapacitorShort-circuit between the two points with the short jig about 10 seconds.
2-2-3. LCD/BT HOLDER SECTION ⋅ BT Holder ⋅ Flash Unit ⋅ LCD Module ⋅ Main Frame ⋅ SW-494 Board
2-3. EXCHANGE METHOD OFBARRIER BLOCK
2-4. EXCHANGE METHOD OFZOOM GEAR BLOCK
- DISASSEMBLY FLOW -
2-3DSC-W80/W85_L2
EXPLODED VIEW HARDWARE LIST2-2. DISASSEMBLY
2-2-1. CABINET SECTIONFollow the disassembly in the numerical order given.1Cabinet (Front) (1-1 to 1-8)2Cabinet (Rear) (2-1 to 2-2)
HELPHELP
Note:On installation of the cabinet (rear), adjust the position of the mode dial switch and the mode dial.
1Cabinet (Front)
Main Board Section(See Page 2-4)
2-1 (#65)
2-2 (#65)
1-1 (#65)
1-4 (#65)
1-5 (#65)
1-6 (#65)
1-7 (Open)
1-8 (Claw)
1-2 (Claw)
1-3
2Cabinet (Rear)
HELP
2-4DSC-W80/W85_L2
EXPLODED VIEW HARDWARE LIST2-2-2. MAIN BOARD SECTIONFollow the disassembly in the numerical order given.1Release Block (1-1 to 1-3)2 Lens Block (2-1 to 2-5)3SY-173 Board (3-1 to 3-11)
2Lens Block(See Page 2-6, 2-8)
1Release Block
3-4 (Solder)
2-42-5
3-5 (#3)
3-8 (#5)
3-1
3-7 (Claw)
3-2
2-2
3-6
3-3
3-10
3-9
1-1
1-3
1-2 (Claw)
3SY-173 Board
HELP
HELP
LCD/BT Holder Section(See Page 2-5)
2-1(Claw)
2-3(Release the clawthat is the fixation of the flash unit once)
Note: High-voltage cautions
Discharging the CapacitorShort-circuit between the two points with the short jig about 10 seconds.
C901
Flash Unit
ST-160 Board
R:1 kΩ/1 W (Part code: 1-215-869-11)
SY-173
3-11
2-5DSC-W80/W85_L2
EXPLODED VIEW HARDWARE LIST
1Flash Unit
2-1 (#5)
1-1 (Claw)
2LCD Panel/SW-494 Board
3BT Holder
3-33-1 (#65)
HELP
HELP
3-2
SW-494
2-2 (Claw)
2-3 (Claw)
2-4 (Claw)
HELP
2-2-3. LCD/BT HOLDER SECTIONFollow the disassembly in the numerical order given.1 Flash Unit (1-1)2 LCD Panel/SW-494 Board (2-1 to 2-4)3 BT Holder (3-1 to 3-3)
2-6DSC-W80/W85_L2
2-3. EXCHANGE METHOD OF BARRIER BLOCK
4 Ornamental ring (A)
2-3-1. HOW TO REMOVE THE ORNAMENTAL RING (A)
1 Turn on the power switch. 2 With the ornamental ring (A) extended, remove the battery forcibly.3 Apply a solvent to the tweezers or a needle, and dissolve the adhesive on
the barrier tapes that secure the ornamental ring (A) to the barrier block.4 Rotate the ornamental ring (A) clockwise to remove.
2-3-2. HOW TO REMOVE THE BARRIER BLOCK
1 Remove two screws.2 Remove the barrier block and the inner ring.
Barrier block
Barrier tape
3 Solvent
2 Barrier block
2 Inner ring
1 Two screws
Tweezers
Note: Do not hold the part of spring.
2-7DSC-W80/W85_L2
2 Ornamental ring (A)
2-3-3. HOW TO INSTALL THE BARRIER BLOCK
1 Install the inner ring and the barrier block.Note: When installing the barrier block, the CAV No. must be located in the lower left position.
2 Secure the barrier block with two screws.*Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)
Note: Check that the barrier feather of the barrier block is not opened slightly or half-closed.
Note: Turn on and off the power to check the opening and closing of the barrier block with the camera in horizontal, up and down directions respectively.Further, check the zoom motion.Rotate the ornamental ring (A) lightly to check that it is not removed.
2-3-4. HOW TO INSTALL THE ORNAMENTAL RING (A)
1 Affix two barrier tapes to the barrier block.Note: The barrier tape must not cover the boss of the barrier block.
2 Install the ornamental ring (A).
Barrier block
CAV No.
Barrier feather
Boss
1 Barrier tape
1 Barrier tape
1 Barrier block
1 Inner ring
2 Two screws
2-8DSC-W80/W85_L2
2-4. EXCHANGE METHOD OF ZOOM GEAR BLOCK
2-4-1. HOW TO REMOVE THE ZOOM GEAR BLOCK
• HOW TO REMOVE THE REAR ASSEMBLY1 Remove the screw, and then the OVF.
2 Remove the shutter flexible board from the connector.3 Remove the vibration-proof flexible board from the connector.4 Peel the adhesive sheet that secures the vibration-proof flexible board.
* When peeling the adhesive sheet, turn it over from the opposite side of the hook.
Screw
2 Shutter flexible board
Connector
Connector
3 Vibration-proof flexible board
4 Adhesive sheet
Vibration-proof flexible board
OVF
Hook
Note: Do not hold the part of terminal and the part of spring.
2-9DSC-W80/W85_L2
5 Peel the adhesive sheet (upper) that secures the main flexible board.6 Disengage the main flexible board from the hook of the ring assembly, and then slide the main flexible board
to remove.7 Peel the adhesive sheet (lower) that secures the main flexible board.
* The FOCUS motor must remain soldered.
8 Remove four screws that secure the rear assembly.9 Remove the rear assembly, disengaging the bosses at four places.
* Take care not to get stuck with the vibration-proof flexible board.
q; Unhook the Z leaf spring to remove.qa Remove the main flexible board from the ring assembly, and remove the rear assembly and the nuruto gear.
6 Main flexible board
7 Adhesive sheet (lower)
Hook
Ring assembly
Ring assembly
qa Nuruto gear
Ring assembly
Vibration-proof flexible board
Boss
Solder of FOCUS motor
5 Adhesive sheet (upper)
8 Four screws
9
Rear assembly
Hook
qa Main flexible board
q; Z leaf spring
qa Rear assemblyBoss
2-10DSC-W80/W85_L2
• HOW TO REMOVE THE ZOOM GEAR BLOCK1 Unsolder the zoom motor.2 Remove the FG leaf spring.3 Remove the main flexible board from the zoom gear block.4 Remove the zoom gear block.
2-4-2. HOW TO INSTALL THE ZOOM GEAR BLOCK
• HOW TO INSTALL THE ZOOM GEAR BLOCK1 Solder the main flexible board to the zoom gear block.2 Install the main flexible board to the zoom gear block.3 Attach the FG leaf spring.
1 Solder 2 FG leaf springHook
Hook
4 Zoom gear block
3 Main flexible board
3 Main flexible board
Rear assembly
1 Solder 3 FG leaf spring
Zoom gear block
2 Main flexible board
2 Main flexible board
Rear assembly
2-11DSC-W80/W85_L2
4 Apply the lubricant (SRX-4339) to the nuruto gear, and insert it into the ring assembly.* Rotate the gear in the ring assembly in the arrow direction until the end of the gear is not engaged
with a concave portion of the ring assembly (because a convex portion of the rear assembly enters the convex portion).
5 Install the zoom gear block on the rear assembly.6 Engaging four bosses, install the rear assembly on the ring assembly.
* The vibration-proof flexible board must be engaged with the hook of the rear assembly.7 Tighten four screws in the order of A to D.
8 Check that the projection of the nuruto shaft that protrudes from the rear assembly is within the specified value given below.*Specified value: 0.005 – 0.395mm
4 Nuruto gear
Ring assembly
Ring assembly
7 Four screws
Hook
6 Vibration-proof flexible board
Nuruto shaft
Nuruto shaft
5 Zoom gear block 6 Rear assembly
Convex portionGear
Boss
Boss
0.005 – 0.395mm
8D
A
B
C
2-12DSC-W80/W85_L2
9 Secure and connect the main flexible board.
q; Secure and connect the vibration-proof flexible board and the shutter flexible board respectively.
Main flexible board
Main flexible board
Adhesive sheet (lower)
Hook
Hook
Ring assembly
Adhesive sheet (upper)
Z leaf spring
HookHook
Shutter flexible board
Connector
Connector
Bousin flexible board
Adhesive sheet
Vibration-proof flexible board
2-13EDSC-W80/W85_L2
qa Install the OVF.*When installing the OVF, fit a projection of OVF in the groove of the ring assembly.
Screw
Ring assembly
OVF
Projection
Groove
2-4-3. CHECK THE OPERATION
Confirm the operation after installing the lens block in the set.1 Power ON/OFF2 Expansion and contraction confirming of lens and opening and shutting confirmation of barrier.
Confirm there are neither dirt nor wounds in the surface of the ornamental ring (A) and lens if there is no problem in operation.Wipe off when dirty.
3 Confirm the operation with Wide/Tele.Note: Do not be of caught etc.
Do not allophone.
HELPDSC-W80/W85_L2
HELPSheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Harness (Black)
MicrophoneHarness (Red)
LC flexible sheet
1mmLight interceptionsheet
Cabinet (front) assy
Main frame
BT holder
SY electrostatic sheet
RL-071/078 board
HELPDSC-W80/W85_L2
BT holder
Notch
Battery terminal board
Battery terminal board
NotchNotch Battery terminal board
1 Insert the battery terminal board into a slit in the BT holder to install.* The battery terminal board is attached with the notch for installation.
2 Fold the notch 3 or 4 times repeatedly to break.
INSTALLATION METHOD OF BATTERY TERMINAL BOARD
• HARNESS ARRANGEMENT
Harness (Red)
Harness (White)
Harness (Black)SY-173 board
DSC-W80/W85_L2
LinkLink
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (2/2)
OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (2/2)
3-1DSC-W80/W85_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
A : VIDEO SIGNALA : AUDIO SIGNALA : VIDEO/AUDIO SIGNAL
SY-173 BOARD (1/2)
VSUB_CONT_PRE,VSUB_CONT_POST
135
Y13Y12
2
AF18GEN_TG_CLK
GEAR_ONGEN_SYS_CLK
CPU(4/10, 5/10)
AF22CA_FD
CA_FD
AE23CA_HD
CA_AD00 - CA_AD13
LENS
7M CCDIMAGER
IC003
IC004
CD-701 FLEXIBLE BOARD
RL-071/078BOARD (1/2)
MC-176 BOARD (1/2)
17 1410 H10
K4
LENS BLOCK
CN301
ZOOMMOTOR
M
SHUTTERMOTOR
M
FOCUSMOTOR
M
FOCUSRESET
SENSOR
ZOOMRESET
SENSORZOOM
FG
YAWMOTOR M
HALLELEMENT
11, 1
3-16
, 18-
2430
, 28,
31, 2
7
K6, K
5, J6
, J5
C3, C
2, B3
C25,
D19,
V19
6
LENS TEMPSENSOR
BUFFER
31, 3
2, 21
, 22
19 34
CCD_OUT
V1, V2, V3A, V3B, V4,V5A, V5B, V6 - V10
H1A,H2A,H1B,H2B
VSTVHLD
39
1712
38
RG
D5D6
27
Q302
CCD SIGNALPROCESS,
TIMINGGENERATOR
(1/10)
IC304
CLOCKGENERATOR
(6/10)
IC202
26
25
C4
E7
VSUBVSUB_CONT
Q301
A4
XLENS_DRIVER_PS H11D4
A2A3
R7, A
F25
AE3
Y10
AD26
IRIS(METER)
IRISMOTOR
M
IC401
IC506
50, 4
938
- 35
33 -
30
FOCUSMOTORDRIVER
IRIS_M_IN, IRIS_M_BRK_2B
FC_DIR_A, FC_DIR_B, FC_EN_A
ZM_DIR_A, ZM_EN_A, ZM_BRK_B
MSHUT_DIR, MSHUT_ENSHUTTER_±SHUTTER(±)
ZOOMMOTORDRIVER
SHUTTERMOTORDRIVER
IRIS MOTORDRIVER
48 -
4524
, 28
FOCUS_A, A, B, BF_MOTOR_A, F_MOTOR_A(-),F_MOTOR_B, F_MOTOR_B(-)
2. Adjust the distance so that the output waveform ofFig. a and the Fig. b can be obtain.
When indicating parts by reference number, pleaseinclude the board name.
(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolyticsand tantalums.
• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.Example C541 L452
22U 10UHTA A 2520
• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.
• Parts with differ according to the model/destination.Refer to the mount table for each function.
• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.
• Signal nameXEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor• 5: fusible resistor• C: panel designation• A: B+ Line• B: B– Line• J : IN/OUT direction of (+,–) B LINE.• C: adjustment for repair.• A: not use circuit(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the
measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon inputimpedance of VOM used.)
Kinds of capacitorCase size
External dimensions (mm)
Yello
w
A AB BA=B
Fig. a (Video output terminal output waveform)
H
Cya
nG
reen
Whi
teM
agen
ta
Red
Blu
e
Fig.b (Picture on monitor TV)
CRT picture frame
Electronic beamscanning frame
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
Precautions for Replacement of Imager• If the imager has been replaced, carry out all the adjustments
for the camera section.• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.In addition, ensure that the receiver is not covered withdusts nor exposed to strong light.
The components identified by mark 0 or dotted line withmark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque 0 sontcritiques pour la sécurité.Ne les remplacer que par une pièce portant le numérospécifie.
DSC-W80/W85_L2
Schematic diagrams of the CD-701 flexible and SY-173 boards are not shown.Pages from 4-5 to 4-15 are not shown.
4-16DSC-W80/W85_L2
MC-176
CN101 XX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V_GND
USB_DM
HD Pr
CHARGE_V
ACV_GND
USB_GND
UART Rx
CHARGE_V
USB_DP
CHARGE_V
V_LINE_OUT
ACV_UNREG
HD Pb
XACC_IN
USB_GND
UART TX
XACV_DET
USB_VBUS
HD Y
AU_LINE_OUT
A_GND
XPOWER_ON
REG_GND
REG_GND
REG_GND
ACV_GND
ACV_UNREG
ACV_GND
ACV_UNREG
REG_GND
Note:CN102 (multi connector) is not supplied,but this is included in MC-176 complete board.
Note:CN101 is not mounted.Flexible flat cable (FFC-095) issoldered to this location instead.This FFC-095 is not supplied, but this is included inMC-176 complete board.
CN102
2
4
6
8
10
12
14
16
18
20
22
24
26
1
3
5
7
9
15
17
19
21
23
25
LND102
USB_DM
V_OUT
HD Pb
CHARGE_V
UART Tx
A_GND
ACV_GND
UART Rx
ACV_UNREG
USB_GND
ACV_GNDHD Pr
USB_DP
ACV_GND
XACC_IN
CHARGE_V
XPOWER_ON
XACV_DET
A_OUT_L
HD Y
USB_VBUS
V_GND
USB_GND
ACV_UNREG
STATIC_GND
MULTI CONNECTORXX MARK:NO MOUNT
(MULTI CONNECTOR)To AV/USB multi cable
Page 4-15
CN710(10/10)SY-173
of Level 3
5
05
A
62 983
D
E
C
F
G
B
7 121141 10
Through the
(FFC-095)flexible flat cable
MC-176 BOARD
4-17DSC-W80/W85_L2
• Refer to page 4-3 for mark 0.
SW-494
XDIRECT_PB
XAE_LOCK_LED
KEY_AD2
KEY_AD1
XSTRB_LED
REG_GND
BL_H
VL_3V
BL_L
D_3.0V
MODE_DIAL1
MODE_DIAL2
D004XX
D003XX
D005XX
54
3 2 1
CN001 XX
1
2
3
4
5
6
7
8
9
10
11
12
Note:CN001 is not mounted. Flexible flat cable (FFC-092) is soldered to this location instead.
Note:S011(mode dial) is not supplied, but this isincluded in SW-494 complete board.
STATIC_GND
BL_H
BL_L
STATIC_GND
(AE/AF LOCK/SELF-TIMER)
(FLASH CHARGING/RECORD)
CONTROL SWITCHXX MARK:NO MOUNT
LITHIUMBATTERY
(MODE DIAL)
(MACRO)(FLASH)(SELF-TIMER) (SET)(DISP)
T(ZOOM)W MENU HOME
BACKLIGHT
LCD901(2/2)
of Level 3
(10/10)CN708
Page 4-15
SY-173
5
05
A
H
62 983
D
E
C
F
G
B
7 121141 10
(FFC-092)
Through theflexible flat cable
R0052200
D001SML-510MWT86S
R0012200
D002SML-310YTT86
BT001
S001
1
3
2
4
S004
1
3
2
4
S006
1
3
2
4
S008
1
3
2
4
S010
1
3
2
4
S002
1
3
2
4
S005
1
3
2
4
S007
1
3
2
4
S009
1
3
2
4
S003
1
3
2
4
LND001
LND002
LND003
LND004
RB0022200
1 23 45 67 8
RB0012200
1 23 45 67 8
RB0032200
1 23 45 67 8
R0062200
R0072200S011
3
4
5
6
1COM
7
8
9
10
11
12
13
14
2
COM
15
16
17
18
SW-494 BOARD
AUTO
AUTO
HIGH SENS
SOFT SNAP
TWILIGHT PORTRAIT
TWILIGHT
LANDSCAPE
LANDSCAPE
BEACH
SNOW
MOVIE
PROGRAM AUTO
4-18DSC-W80/W85_L2
• Refer to page 4-3 for mark 0.
ST-160
C005XX
C006XX
R005XX
NO MARK:REC/PB MODE
262
04.1
0
3.1
0 0
4.1
5
0
C00122u
C0040.047u250V
CL001
D001MA2YF8000LS0
L0012.2uH
LND016
CHARGE-
LND015
CHARGE+
LND020
XE_K(L)
LND019
XE_A(H)
LND018TRIG_GND
LND017
TRIGGER
R0021M
R0041M
CN001 12P
1
2
3
4
5
6
7
8
9
10
11
12
D002CL-360S-TD4-X-TL
54 3
12
6
R003100
C007220p
C0021u
T001
1
2 3
4
D003RB520S-40TE61
R0064700
Q001CY25BAJ-8F-T23-G02
1
8
5
2
3
4
6
7
IC001TPS65552RGTR
1 SW
2 SW
3 VCC4 F_ON
5
N.C
6I_
PEA
K7
G_I
GB
T
8
N.C
XFULL 9
CHG 10
PGND 11
PGND 12
N.C
13
N.C
14
VB
ATT
15
N.C
16
HG
ND
17
C90149u
315V
ST_UNREG
STB_CHG_CNT
XSTRB_FULL
REG_GND
XAF_LED
STRB_ON
STRB_CHG
TI_5.0V
REG_GND
AF_5.0V
ST_UNREG
NC
FLASH DRIVEXX MARK:NO MOUNT
SELF-TIMER/AF ILLUMINATOR
CAPACITORCHARGING UNIT
FLASH
SY-173
CN701
of Level 3Page 4-15
(10/10)
CHARGE CONTROLFLASH CONTROL,
5
05
A
62 983
D
E
C
F
B
7 121141 10
flexible flat cableThrough the
(FFC-093)
FLASH DRIVE
IC001
ST-160 BOARD
4-19DSC-W80/W85_L2
RL-071/078
CN101 XX
1
2
3
4
5
6
7
8
D_3.0V
X_PWR_LED
MIC_SIG
REG_GND
XAE_LOCK_SW
XSHUTTER_SW
MIC_GND
XPWR_ON
Note:CN101 is not mounted. Flexible flatcable (FFC-094) is soldered to thislocation instead.
Note:In this set, either RL-071 or RL-078 board is used.All mounted parts and schematic diagramare common to both RL boards.
S1021
3
2
4
LND102
D101SML-412MWT86
S101
56
1 3
4 2
LND101
LND103
LND104
C0010.047u
C0020.047u
MIC_GND
MIC_SIG
STATIC_GND
STATIC_GND
POWER
(POWER)
(SHUTTER)
XX MARK:NO MOUNT
CONTROL SWITCH,MIC MIC901MICROPHONE
BLOCK
(10/10)CN707
Page 4-15
SY-173
of Level 3
5
05
A
62 3
D
E
C
B
41
Through theflexible flat cable
(FFC-094)
RL-071/078 BOARD
4-3. PRINTED WIRING BOARDS
DSC-W80/W85_L2
LinkLink
SW-494 BOARD
MC-176 BOARD
RL-071/078 BOARD
ST-160 BOARD
MOUNTED PARTS LOCATIONCOMMON NOTE FOR PRINTED WIRING BOARDS
: Flexible boardPattern from the side which enables seeing.
: pattern of the rear side(The other layers’ patterns are not indicated)
• Through hole is omitted.• Circled numbers refer to waveforms.• There are a few cases that the part printed on diagram
isn’t mounted in this model.• C: panel designation
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
2 1
3
2 1
3
2 1
3
345
21
123
654
EB
C
31
5
2
46
123
654
31
5
2
46
123
54
4 3
1 2
31 2
45
53 4
12
14
23
46
2
5
31
12
43
14
23
• Chip parts.Transistor Diode
DSC-W80/W85_L2
Printed wiring boards of the CD-701 flexible and SY-173 boards are not shown.Pages from 4-23 to 4-25 are not shown.
4-26DSC-W80/W85_L2
MC-176 (4 layers), SW-494 (2 layers)
: Uses unleaded solder.
MC-176, SW-494
AK
AK
S001
S002
S003
S004
S005
S006
S007
S008
S009
S010
D001
D002
D003
D004
D005
LND002
LND003
LND004
RB001
RB002
RB003
R001
R005
R006
R007
S011
4 2
13
4 2
13
42 1
3
421
3
4 2
13
42
1 3
42 1
3
42 1
3
42 1
3
42 1
3
A K
AK
451 3
1 72 8
39
45
61
78
171614
132
1211
10
1815
1728
1 72 8
SW-494 BOARD (SIDE A)
1-871-501-
11 12
Note: S011 (mode dial) is not supplied, but this is includedin SW-494 complete board.
MENU
(DISP)
S011(MODE DIAL)
HOME
v
(MACRO)b
(SELF TIMER)V
(SET)z (FLASH)B
N
(ZOOM)W T
D001(AE/AF LOCK/SELF-TIMER)
D002(FLASH CHARGING/RECORD)
C
D
A
1 2 3 4 505
B
TO LCD901(BACKLIGHT)
BL-L
BL-H
CN001 BT00
1
LND001
112
–
+
SW-494 BOARD (SIDE B)
1-871-501- 11 12
BT001LITHIUMBATTERY
Note: CN001 is not mounted. Flexible flat cable (FFC-092) is soldered to this location instead.
C
D
A
1234505
B
MC-176-
>EP GW<
A226 2728 1
25CN102
MC-176 BOARD (SIDE A)
1-871-499- 11 12(MULTI CONNECTOR)
Note: CN102 (multi connector) is not supplied, but this is included in MC-176 complete board.
05
CN101
LND102
130
MC-176 BOARD (SIDE B)
1-871-499- 11 12
Note: CN101 is not mounted. Flexible flat cable (FFC-095) is soldered to this location instead. This FFC-095 is not supplied, but this is included in MC-176 complete board.
05
CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
4-27DSC-W80/W85_L2
ST-160 (4 layers), RL-071/078 (2 layers)
: Uses unleaded solder.
ST-160, RL-071/078
>EP GW<
-
+
516
8131
4
129
17
CN001C001
C002
C004
C005
C006
D001
IC00
1
T001
LND017LND018
LND019LND020
CL001
L001
R004
R005
LND015
LND016
C007
D003 R0
06
1
2
11
12
AK
12
43
AK
ST-160 BOARD (SIDE A)
1-871-500- 11
12
FLASH UNITXE_K (L) XE_A (H)
TRIG_GND TRIGGER
C901CHARGINGCAPACITOR
+
A
1 2 305
B
BST-160
8
5
1
4
D002
Q001
R002
R003
134
6
ST-160 BOARD (SIDE B)
1-871-500- 11
12
SELF-TIMER/AF ILLUMINATOR
A
1 2 305
B
S102
D101
LND103
S101
C002
C001
421
3
341
2 65
RL-071 BOARD (SIDE A)
1-871-502- 12S101
(SHUTTER)
(POWER)
POWERS102
K A
05
-502-1-871
RL-071B
>EP GW<
R B
CN101
LND101LND102
LND104
18
RL-071 BOARD (SIDE B)
1-871-502- 12
MIC901MICROPHONE
BLOCK
Note: CN101 is not mounted. Flexible flat cable (FFC-094) is soldered to this location instead.
05
A
>EP
GW<
1-874-109-
RL-0
78
S102
D101
LND103
S101
C002
C001
421
3
341
2 65
RL-078 BOARD (SIDE A)
1-874-109- 11S101
(SHUTTER)
(POWER)
POWERS102
K A
05
-109-1-874
RL-078B
>EP GW<
R B
CN101
LND101LND102
LND104
18
RL-078 BOARD (SIDE B)
1-874-109- 11
MIC901MICROPHONE
BLOCK
Note: CN101 is not mounted. Flexible flat cable (FFC-094) is soldered to this location instead.
05
Note: In this set, either RL-071 or RL-078 board is used.All mounted parts and schematic diagram are common to both RL boards.
DSC-W80/W85_L2
Mounted parts location of the SY-171 board is not shown.Pages 4-29 and 4-30 are not shown.
• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European modelTW : Taiwan model
When indicating parts by reference number,please include the board name.
• Color Indication of Appearance PartsExample:(SILVER) : Cabinet’s Color(Silver) : Parts Color
5-2
5. REPAIR PARTS LIST5. REPAIR PARTS LIST
DSC-W80/W85_L2
DISASSEMBLY HARDWARE LIST
Ref. No. Part No. Description Ref. No. Part No. Description
The CD-ROM supplied contains all of language version ofThe CD-ROM supplied contains all of language version ofthe Handycam Handbook (PDF) for printing.・ The printed matter is not supplied. If required, please
order it with the part number below.・ (Only for destination Japanese model) 日本国内については日本語のみが印刷での部品供給可能です。
Ver. 1.1 2008.05The changed portions fromVer. 1.0 are shown in blue.
SUPPLEMENT-1File this supplement with the service manual.
(DI08-010)
• Change of Board’s Suffix No.• Change of Repair Parts• Revision of Accessories
Note: Please refer to Ver. 1.1 of SERVICE MANUAL (9-852-194-31) for the revision of accessories.
• Suffix No. of MC-176 and ST-160 boards have been changed from 11 , 12 into 12 , 22 .About suffix No. 11 and 12 , 22 , there are no change of schematic diagram and printed wiring board.
DSC-W80/W85US Model
Canadian ModelAEP Model
UK ModelE Model
Australian ModelHong Kong Model
Chinese ModelKorea Model
Argentine ModelBrazilian Model
Japanese ModelTourist Model
DSC-W80/W85_L2
— 2 —DSC-W80/W85_L2
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS& : Points added portion.
Page Former New
Ref. No. Part No. Description Ref. No. Part No. Description
Note 2: The RL-071 flexible board is compatible with theRL-078 flexible board.When replace the RL-078 flexible board, change itto the RL-071 flexible board.
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part numberspecified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
#28: M1.4 X 4.0 (Tapping)(Dark Silver)3-348-998-61
1.4
4.0
#29: M1.4 X 2.5 (Black)2-662-396-01
#31: M3.0 X 4.0(Silver)2-102-434-01
2.5
1.4
#30: M1.2 X 3.5 (Tapping)(White)3-086-156-11
3.5
1.2
#32: M2.0 X 4.5 (Tapping)(Silver)2-102-498-01
#33: M3.0 X 6.0 (Silver)3-077-331-21
#35: M4.0 X 6.0 (Tapping)(Silver)3-975-291-02
#34: M3.0 X 8.0 (Black)3-077-331-41
#36: M3.0 X 6.0 (Silver)4-886-821-11
#37: M2.0 X 6.0 (Tapping)(Black)3-080-206-31
#38: M3.0 X 20.0 (Tapping)(Silver)7-685-651-79
#40: M2.0 X 4.0 (Tapping)(Silver)7-685-851-04
#39: M2.6 X 5.0 (Tapping)(Black)7-685-791-09
4.0
3.0
4.5
2.0
6.0
3.0
8.0
3.0 4.0
6.0 6.0
3.0
6.0
2.0
20.0
3.0
4.0
2.0
5.0
2.6
HARDWARE LIST (3/4)
#41: M3.0 X 8.0 (Tapping)(Silver)3-065-748-01
8.0
3.0
#42: M2.0 X 4.0 (Tapping)(Silver)7-628-253-00
2.0
4.0
#43: M1.7 X 4.0 (Red)2-660-401-31
4.0
1.7
#46: M1.7 X 3.0 (Red)2-660-401-11
#45: M1.4 X 2.5 (Silver)2-587-151-01
#47: M1.4 X 3.0 (Tapping)(Silver)2-665-774-01
3.0
1.4
#44: M1.7 X 3.0 (Tapping)(Silver)3-078-890-61
3.0
1.7
3.0
1.7
2.5
1.4
#48: M1.7 X 2.5(Silver)3-973-497-91
2.5
1.7
#49: M2.0 X 4.0(Black)2-630-005-31
#50: M2.0 X 3.0(Red)2-891-494-11
#51: M2.0 X 2.5 (Silver)3-073-686-01
#54: M1.75 X 6.0 (Tapping)(Black)3-318-203-11
#53: M2.0 X 5.0 (Tapping)(Black)3-080-206-21
#55: M2.0 X 4.0(Silver)2-655-582-11
#52: M2.0 X 4.0 (Tapping)(Black)3-080-206-11
#56: M2.0 X 3.5(Silver)3-067-187-11
4.0
2.0
3.0
2.0
2.5
2.0
5.0
2.0
4.0
2.0
6.0
1.75
4.0
2.0
3.5
2.0
#57: M1.7 X 4.0(Black)7-627-852-18
4.0
1.7
#58: M2.0 X 6.0 (Tapping)(Silver)3-719-408-11
6.0
2.0
#59: M2.0 X 5.0 (Tapping)(Silver)3-080-205-21
#60: M2.6 X 5.0(Black)3-061-062-11
5.0
2.0
5.0
2.6
HARDWARE LIST (4/4)
#61: M3.0 X 10.0(Black)7-682-549-09
10.0
3.0
#62: M2.0 X 3.0(Silver)3-080-202-21
3.0
2.0
#63: M5.0 X 12.5(Black)3-060-811-21
12.5
5.0
#64: M1.7 X 5.0 (Tapping)(Silver)2-666-551-21
5.0
1.7
#65: M1.4 X 3.5 (Silver)2-635-591-01
3.5
1.4
#66: M1.4 X 1.4 (Silver)2-635-591-41
1.4
1.4
#71: M1.4 X 2.0 (Red)3-208-537-01
2.0
1.4
#67: M1.4 X 2.0 (Silver)3-389-523-16
2.0
1.4
#68: M1.7 X 4.0 (Silver)2-655-581-01
4.0
1.7
#69: M1.7 X 3.0 (Silver)2-599-475-21
3.0
1.7
#70: M1.7 X 5.0 (Silver)2-599-475-41
5.0
1.7
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Printing a text1. Click the Print button .2. Specify a printer, print range, number of copies, and other op-
tions, and then click [OK].
Application of printing:To set a range to be printed within a page, select the graphic
selection tool and drag on the page to enclose a range tobe printed, and then click the Print button.
Finding a text1. Click the Find button .2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual:To execute “find” from current page toward the previous pages,select the check box “Find Backward” and then click the“Find”.
3. Open the find dialog box again, and click the [Find Again] andyou can find the matched character strings displayed next.(Character strings entered previously are displayed as they arein the text box.)
Application to the Service Manual:The parts on the drawing pages (block diagrams, circuit dia-grams, printed circuit boards) and parts list pages in a textcan be found using this find function. For example, find aRef. No. of IC on the block diagram, and click the [Find Again]continuously, so that you can move to the Ref. No. of IC onthe circuit diagram or printed circuit board diagram succes-sively.Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Switching a page• To move to the first page, click the .
• To move to the last page, click the .
• To move to the previous page, click the .
• To move to the next page, click the .
Reversing the screens displayed once• To reverse the previous screens (operation) one by one, click
the .
• To advance the reversed screens (operation) one by one, click
the .
Application to the Service Manual:This function allows you to go and back between circuit dia-gram and printed circuit board diagram, and accordingly itwill be convenient for the voltage check.
Moving with link
1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, orblue characters on the removal flowchart page or drawingpage), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:Click an item (text) on the bookmark pallet, and you can moveto the link destination. Also, clicking can display thehidden items.(To go back to original state, click )
Zooming or rotating the screen display“Zoom in/out”• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click or for zoom-
ing in or out.
“Rotate”• Click rotate tool , and the page then rotates 90 degrees each.
Application to the Service Manual:The printed circuit board diagram you see now can be changedto the same direction as the set.
Toolbar
Revision History
Reverse
DSC-W80/W85_L2
Ver.
1.0
1.1
Date
2007.03
2008.05
History
Official Release
Supplement-1(S1 DI08-010)
Contents
—
• Change of Board’s Suffix No.• Change of Repair Parts• Correction of Self-diagnosis Code Table• Revision of AccessoriesS.M. revised: Page 1-6, Page 5-14, Page 5-15
![POWER AMPLIFIER 25 - ATW.huusers.atw.hu/bazsielektron/Hang Auto/kenwood_kac-629s_[ET].pdf · POWER AMPLIFIER KAC-629S ... W85 R175 C81 R81 C51 C74 VR1 W117 W118 W119 W120 W121 ...](https://static.documents.pub/doc/80x56/5aabec757f8b9a693f8c92e5/power-amplifier-25-atw-autokenwoodkac-629setpdfpower-amplifier-kac-629s.jpg)
