LCD PROJECTION TELEVISIONSERVICE MANUALLA-4 CHASSISMODEL NAMEREMOTE COMMANDERDESTINATION9-883-709-02KDF-46E2000RM-YD010US/CND KDF-46E2010RM-YD010MEXICO KDF-50E2000RM-YD010US/CND KDF-50E2010RM-YD010MEXICO KDF-55E2000RM-YD010US/CND KDF-55E2010RM-YD010MEXICO HISTORY INFORMATION FOR THE FOLLOWING MANUAL:ORIGINAL MANUAL ISSUE DATE:5/2006 :UPDATED ITEM REVISION DATESUBJECT 5/2006No revisions or updates are applicable at this time.6/2006Replaced Pages 70, 72, & 73 to include Power supply note.LCD PROJECTION TELEVISIONSERVICE MANUALLA-4 CHASSISMODEL NAMEREMOTE COMMANDERDESTINATION9-883-709-02KDF-46E2000RM-YD010US/CND KDF-46E2010RM-YD010MEXICO KDF-50E2000RM-YD010US/CND KDF-50E2010RM-YD010MEXICO KDF-55E2000RM-YD010US/CND KDF-55E2010RM-YD010MEXICO Self DiagnosisSupported modelKDF-50E2010 RM-YD010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20103TABLE OF CONTENTSSECTION TITLEPAGE SECTION TITLEPAGESpecications ................................................................................. 4Warnings and Cautions .................................................................. 6Safety Check-Out ........................................................................... 7Self-Diagnostic Function ................................................................. 8SECTION 1:DISASSEMBLY ............................................................... 141-1.Overview .............................................................................. 141-2.Rear Cover Removal ............................................................ 151-3.Chassis Removal and Service Position ............................... 161-4.G Board Removal ................................................................. 161-5.B Block Assembly, A Block Assembly, Antenna, U Board and K Board Removal ............................................ 171-6.Lamp Block Assembly and Optical Block Removal .............. 181-6-1.Lamp Connector and T2 Board Removal ................ 191-6-2.Lamp Driver Fan Removal ....................................... 201-7.HC Board Removal .............................................................. 211-8.HA Board and HB Board Removal ....................................... 211-9. Screen Frame Assebmly and Speaker Removal ................ 221-10. Mirror Assembly and Mirror Cover Assembly Removal ........ 23Wire Dressing ....................................................................... 24Caution Points ...................................................................... 42SECTION 2:CIRCUIT ADJUSTMENTS .............................................. 492-1.Using the Remote Commander for Electrical Adjustments .. 492-2.Accessing Service Adjustment Mode ................................... 492-3.Viewing the Service Menus .................................................. 492-4.Using the Remote Commander to Change Service Data .... 502-4-1.Exiting Service Mode ............................................... 512-5.Verifying Service Data Changes .......................................... 512-6.Resetting Wega (User) Menu to Factory Defaults ............... 512-7.H/V Center Conrmation and Adjustments .......................... 522-8.IRIS Adjustments .................................................................. 52SECTION 3:DIAGRAMS ..................................................................... 533-1.Circuit Boards Location ........................................................ 533-2.Printed Wiring Boards and Schematic Diagrams Information ......................................... 533-3.Signal Flow Block Diagram .................................................. 553-4.Schematics and Supporting Information .............................. 56A Board Schematic Diagram ................................................ 56B Board Schematic Diagram (1 of 11) .................................. 58B Board Schematic Diagram (2 of 11) .................................. 59B Board Schematic Diagram (3 of 11) .................................. 60B Board Schematic Diagram (4 of 11) .................................. 61B Board Schematic Diagram (5 of 11) .................................. 62B Board Schematic Diagram (6 of 11) .................................. 63B Board Schematic Diagram (7 of 11) .................................. 64B Board Schematic Diagram (8 of 11) .................................. 65B Board Schematic Diagram (9 of 11) .................................. 66B Board Schematic Diagram (10 of 11) ................................ 67B Board Schematic Diagram (11 of 11) ................................ 68G Board Schematic Diagram (1 of 2) ................................... 70G Board Schematic Diagram (2 of 2) ................................... 71HA Board Schematic Diagram ............................................. 74HB Board Schematic Diagram ............................................. 76HC Board Schematic Diagram ............................................. 78K Board Schematic Diagram ................................................ 80S2 Board Schematic Diagram .............................................. 83T1 Board Schematic Diagram .............................................. 86T2 Board Schematic Diagram .............................................. 86U Board Schematic Diagram ................................................ 913-5.Semiconductors ................................................................... 93SECTION 4:EXPLODED VIEWS ........................................................ 944-1.Covers .................................................................................. 944-2.Chassis ................................................................................ 954-3.Optics Unit Block Assembly and Lamp Assembly ................ 96SECTION 5:ELECTRICAL PARTS LIST ............................................ 97APPENDIX A:REPLACING THE LAMP ............................................A-1KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20104SPECIFICATIONSDesign and specications are subject to change without notice.120V AC, 60Hz200WLess than 0.8WHDMI IN2 Video - 1080i, 720p, 480p, 480i1 Audio - Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20, and 24 bitVideo (IN)3 total (1 on side panel)1Vp-p, 75ohms unbalanced, sync negative S Video (IN)1 totalY: 1Vp-p, 75ohms unbalanced, sync negative C: 0.286Vp-p (Burst signal), 75ohmsAudio (IN)5 total (1 on side panel) 500 mVrms (100% modulation)Impedance:47 kilo ohmsPower RequirementsPower Consumption (W)In Use (Max)In Standby Inputs/Outputs Component Video Input3 (Y, PB/CB) (1 on Side Panel)Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative PB: 0.7 Vp-p, 75 ohms;PR: 0.7 Vp-p, 75 ohms Audio (VAR/FIX) Out1 total 500 mVrms at the maximum volume setting (Variable)500 mVrms (Fixed)Impedance (Output):2 kilo ohmRF Input2 totalDigital Audio Optical Output (PCM/Dolby Digital)1 totalOptical RectangularKDF-46E2000KDF-46E2010KDF-50E2000KDF-50E2010KDF-55E2000KDF-55E2010Speaker Output (W)Dimensions (W x H x D)mm 1096 x 766 x 382 mm 1184 x 827 x 408 mm 1301 x 907 x 442 mmin 431/4 x 30 1/4 x 15 1/8 in 46 5/8 x 32 5/8 x 16 1/8 in 511/4x 35 3/4 x 17 1/2 inMasskg 27 kg 29.3 kg 34 kglbs 59 lbs 5 oz 64 lbs 7 oz 75 lbs12W (L), 12W (R)Trademark InformationAs an ENERGY STAR Partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a U.S. registered mark.TruSurround XT, SRS and the ( ) symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. BBE and BBE Symbol are trademarks of BBE Sound, Inc. and are licensed by BBE Sound, Inc. under U.S. Patent No. 4,638,258 and 4,482,866.This TV incorporates High-Definition Multimedia Interface (HDMI) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.This TV is manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.Macintosh is a trademark licensed to Apple Computer, Inc., registered in the U.S.A and other countries. WEGA, Grand WEGA, WEGA GATE, Steady Sound, Digital Reality Creation and CineMotion are registered trademarks of Sony Corporation.BRAVIA andare trademarks of Sony Corporation.KDF-46E2000/50E2000/55E2000 KDF-46E2010/50E2010/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20105Television systemAmerican TV standard, NTSCATSC Compliant 8VSB, ATSC (8VSB terrestrial)ANSI/SCTE 07 2000, QAM on cableChannel coverageTerrestrial 2-69/ Cable TV: 2-125 (analog)Terrestrial 2-69/ Cable TV: 2-135 (digital)Screen Size (measured diagonally)46 inches (KDF-46E2000/46E2010 Only) 50 inches (KDF-50E2000/50E2010 Only) 55 inches (KDF-55E2000/55E2010 Only) Antenna75-ohm external antenna terminal for VHF/UHFProjection System3 LCD Panels, 1 lens projection systemLCD Panel0.73 inch TFT LCD panel (1,280 x 720 pixels)Projection LensHigh Performance, large diameter hybrid lens F2.4Lamp100W, XL-2400 Ultra High Pressure LampSupplied AccessoriesRemote Commander RM-YD010Two Size AA (R6) BatteriesOperating InstructionsQuick Setup GuideWarranty CardProduct Registration CardOptional AccessoriesHDMI CableHDMI-to-DVI CableComponent Video CableS VIDEO CableA/V CableAudio CableTV Stand: SU-RG12S (KDF-46E2000/46E2010 Only)SU-RG12L (KDF-50E2000/50E2010/55E2000/55E2010 Only)KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20106WARNINGS AND CAUTIONSCAUTIONThese servicing instructions are for use by qualied service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualied to do so.WARNING!!An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is directly connected to the AC power line.! SAFETY-RELATED COMPONENT WARNING!!Components identied by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identied in this manual. Follow these procedures whenever critical components are replaced or improper operation is suspected. ATTENTION!!Ces instructions de service sont lusage du personnel de service quali seulement. Pour prvenir le risque de choc lectrique, ne pas faire lentretien autre que celui contenu dans le Mode demploi moins que vous soyez quali faire ainsi.An deviter tout risque delectrocution provenant dun chssis sous tension, un transformateur disolement doit etre utilis lors de tout dpannage. Le chssis de ce rcepteur est directement raccord lalimentation du secteur.! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!Les composants identies par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont dune importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont limportance est critique pour la securite du fonctionnement sont identies dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsquun mauvais fonctionnement suspecte.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20107SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer:1.Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.2.Check the interboard wiring to ensure that no wires are pinched or touching high-wattage resistors.3.Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.4.Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.5.Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.6.Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.7.Check the B+ and HV to see if they are specied values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV.8.Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.Leakage TestThe AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instructions.2.A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate low voltage scale. The Simpsons 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).How to Find a Good Earth GroundA cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also at earth ground. If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground potential (see Figure B).To Exposed MetalParts on Set0.15 FEarth GroundACVoltmeter(0.75V)Trouble LightAC Outlet BoxOhmmeterCold-water PipeFigure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20108SELF-DIAGNOSTIC FUNCTION Self DiagnosisSupported modelThe units in this manual contain a self-diagnostic function. If an error occurs, the POWER/STANDBY will automatically begin to ash. The number of times the LED ashes translates to a probable source of the problem. A denition of the POWER/STANDBY ash indicators is listed in the instruction manual for the users knowledge and reference. If an error symptom is difcult to reproduced use the Remote Commander to display the record that is stored at the internal NVM to specify the cause of the failure.Diagnostic Test IndicatorsWhen an error occurs, the POWER/STANDBY will ash a set number of times to indicate the possible cause of the problem. If there is more than one error, the POWER/STANDBY will identify the rst of the problem areas. If the errors occur simultaneously, the one that corresponds to the fewest ashes is identied rst.Results for all of the following diagnostic items are displayed on screen. (No error has occurred if the screen displays a 0.)Detected symptomsLamp cover /Lamp position errorTemp error3 times2 times4 times5 times6 times8 times- Lamp cover is notsecurely attached (T1 Bd) - Set temperture is high.- Temp sensor connector is not attached securely.(CN110 on HB board,CN160 on S2 board)-Lamp is not inserted properly (T2 Bd)Diagnosis ItemNumber of timesPOWER/STANDBYindicator blinksProbable Cause/LocationLamp driver error- Lamp driver is faulty.LowB LVP Thermal Fuse Open - Check 10.5Vaudio IC(B Board)- Lamp is burnt out.LowB OVP-B -10.5V is over voltage.(B board)- Fan 1-4 power is notsupplied. (B board)- F-Fan caught wires or harnesses.an connector is notsecurely attached . .Lamp Error LAMP-LED flashes- No Picture/No sound- No Picture/No sound- No Picture/No sound- No Picture/No sound- Relay click on/off- No Picture/No sound- No Picture/No soundFan errorKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20109DISPLAY OF POWER/STANDBY OR LAMP LED FLASH COUNTPUSH OPEN POWER/STANDBY POWER TIMER LAMPIndicatorsScreen- One flash is not used for self-di agnosis.Number of times LED FlashLamp cover 3 timesFan 4 timesLED ON : 0.3 secLED OFF : 0.3sec LED OFF3.0 secLED OFF3.0 secExampleDiagnosisRELEASING THE POWER/STANDBY LED FLASHUnplug the power cord from the outlet to temporarily stop the POWER/STANDBY lamp from ashing.Self-Diagnostic Screen DisplayFor failures that are difcult to reproduce, or accompany occasional power off and/or picture mute, the Self-Diagnostic screen display is useful to specify the cause.VIEWING THE SELF-DIAGNOSTIC SCREEN1.TV must be in standby mode. (Power off).2.Press the following buttons on the Remote Commander within a second of each other: DISPLAY Channel 5 Volume - POWERNOTE:This differs from the method of accessing service mode which is Volume+Sample Self-Diagnostic Screen Display SELF CHECK1 : LAMP_ERR 002 : Lamp Temp Over 03 :4 :LAMP_ COVERFAN_ERR 15 : LAMP_DRIVER6 : LowB-ERROR 008 : D_OVP 0WDT 101 : 0Name:KDF-50E2000Serial:XXXXXXX"1" is displayed when an error is detected one or more times"0" is displayed when no error has been detectedNOTE: To refresh the Self Check menu when all the items are not displayed, press JUMP on the Remote Commander. 3.Proceed to Viewing the Self-Diagnostic Errors.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201010VIEWING THE SELF-DIAGNOSTIC ERRORSThe TV MICRO service menu contains a Log category that stores the errors. To view the rst error detected, display the SHUTDOWN_LOG1 Adjustment Item of the STATUS category. If other errors are detected, they are stored in the SHUTDOWN_LOG2 Adjustment Item of the STATUS category.1.TV must be in standby mode. (Power off).2.Press the following buttons on the Remote Commander within a second of each other: DISPLAY Channel 5 Volume+POWER. ServiceMenuCategoryAdjustmentItemItem NumberData ValueVERSION0 0 SERVICEVERS Wide ZoomVideo 1WSL:480IF/A:0000000000000000CBA:00000000000000003.Do one of the following:a.If the TV MICRO Service Menu is displayed, proceed to the next step.b.If the TV Micro Service Menu is not displayed, press JUMP on the Remote Commander until the TV MICRO service menu is displayed.4.Do one of the following:a.If the STATUS Category is displayed, proceed to the next step.b.If the STATUS Category is not displayed, press2 or5 on the Remote Comman until the STATUS Category is displayed.5.The SHUTDOWN_LOG1 Adjustment Item is the rst item of the STATUS Category and contains the rst error the set detected.6.To view additional errors, press1 until the SHUTDOWN_LOG2 Adjustment Item is displayed7.After repairing the errors, proceed to Clearling the Self-Diagnostic Screen. CLEARING THE SELF-DIAGNOSTIC SCREENThe self-diagnostic results displayed on the screen are not cleared automatically, therefore you should always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the self-diagnostic screen to reset the results to 0. Note: The self-diagnostic function will not be able to detect any subsequent faults after completion of the repairs unless the Self-Diagnostic result display is cleared to reset the results to 0.1.If the Self-Diagnostic screen is already displayed, proceed to step 3. If not, Power off (Set to Standby mode).2.Press DISPLAY Channel 5 Sound Volume - POWER3.Press Channel 8 ENTThe status in the upper right corner changes to WRITE. When the operation is complete, the status returns to SERVICE and the Self-Diagnostic screen is reset.4.To exit the Self-Diagnostic screen, turn the power off.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201011SELF-DIAGNOSTIC FUNCTION OPERATION7HPS :KHQWKHWHPSHUDWXUHVHQVRURQWKH6ERDUGGHWHFWVKLJKWHPSHUDWXUHRU,&OLQHFRQQHFWRU&1*ERDUG&16ERDUGLVQRWVHDWHGVHFXUHO\WKH79PLFURWXUQVRIIWKHODPS:KHQWKHWHPSHUDWXUHVHQVRURQWKH+%ERDUGGHWHFWVKLJKWHPSHUDWXUHRU,&OLQHFRQQHFWRU&1%ERDUG&1+%ERDUGLVQRWVHDWHGVHFXUHO\WKH79PLFURWXUQVRIIWKHODPS /DPS&RYHU/DPS3RVLWLRQ7KHULEDWWKHEDFNRIWKHODPSFRYHUFORVHVWKH6:RQWKH7ERDUG7KHODPSFORVHVWKH6:RQWKH7ERDUG,WLVPRQLWRUHGE\WKH79PLFURSLQRI,&DQGWXUQVRIIWKHODPSZKHQLWLVRSHQHG )DQ(UURU )DQURWDWLRQLVGHWHFWHGE\)$13527DQGWKH79PLFURSLQRI,&WXUQVRIIWKHODPSZKHQLWLVKLJK /DPSGULYHU :KHQWKH/$033527SLQ,&LVKLJKWKHODPSLVQRWWXUQHGRQ,IWKH/$03+9'(7SLQ,&LVORZDWWKHVDPHWLPHLWLVFODVVLILHGDVQRKLJKYROWDJHRIWKHODPSGULYHU /RZ%/93 :KHQQR%B9LVGHWHFWHGSLQRI79PLFURLVORZDQGLWWXUQVRIIWKHPDLQSRZHU /RZ%293 :KHQRYHUYROWDJHRI%B9LVGHWHFWHGSLQRIWKH79PLFURLVORZDQGLWWXUQVRIIWKHPDLQSRZHU /$03/DPS :KHQWKH/$033527SLQRI,&QRUPDOO\DW9LVKLJK9WKH6HOI'LDJQRVLVGHWHFWVWKHSUREOHPDQGSXWVWKHVHWLQWR/DPSSURWHFWPRGHDQGWXUQVWKHODPSRII,IWKH/$03+9'(7SLQRI,&LVKLJKDWWKHVDPHWLPHLWVFODVVLILHGDVQRODPSRUDEXUQHGRXWODPS

KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201012SELF-DIAGNOSTIC BLOCK DIAGRAMFAN 1FAN 2FAN 3FAN 4S2 BOARDIC160TEMPSENSORIC110TEMPHB BOARDSENSORGBOARD B BOARD137I_FAN_PROT129126LB-ERRORD_OVP10. 5VI 2CI 2CI 2CI 2CT1 BOARDT2 BOARD31SW3SW1HV-DETLAMP DRIVER150I_LAMP_COVERI_LAMP_PROT151I_HV_DET152IC3002TV Micro-computer3322CN6800CN6805CN6801CN680298101171CN6804CN680310612CN69042CN6904CN30022CN300212610KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201013READING LAMP AND PANEL TIMEThe TV_Micro menu of the Service Menu displays the current lamp and panel time of a set. The Lamp Hours and Panel Hours are shown in hexadecimal format.1.TV must be in standby mode. (Power off).2.Press the following buttons on the Remote Commander within a second of each other: DISPLAY Channel 5 Volume+POWER.One of the three Service Menu displays. (For more information regarding the Service Menus, see 2-2. Accessing Service Adjustment Mode.)VERSION0 0 SERVICEVERS Wide ZoomVideo 1WSL:480I3.To read the Lamp time, press 4 to display the TIME category and the LMPH item.The screen displays:Wide ZoomTVTIME0 0 SERVICELMPHLMPH:01HLMPL:A0HTotal LAMP TIME is 416 hours Total hours 256Total hours 1604.To read the Panel time, press 4 to display the PHLH item.Wide ZoomTVTIME0 0 SERVICEPNLHPNLH:01HPNLL:A0HThe screen displays:Total PANEL TIME is 416 hours Total hours 256Total hours 1605.Do one of the following:a.If you have replaced the lamp, proceed to step 4 of Resetting the Lamp Time.b.If you have not replaced the lamp, turn off the set by pressing POWERRESETTING THE LAMP TIMEWhen replacing the lamp, use the following to reset the lamp time.1.If the Self-Diagnostic screen is already displayed, proceed to step 4. If not, Power off (Set to Standby mode).2.Press DISPLAY Channel 5 Sound Volume - POWER3.To access the Lamp reset, press 5 until the TIME category displays.4.Press 1 until the RSET item displays. Wide ZoomTVTIME0 0 SERVICERSET5.To reset the Lamp time, press3 to change the data value to 1.Wide ZoomTVTIME0 1 SERVICERSET6. PressMUTING ENTto write the change into memory.Wide ZoomTVTIME0 1 WRITERSET6.To verify the Lamp has been resetpress 5 until the TIME category displays, and then press 1 until the LMPH item displays.NOTE: You cannot reset the Panel time with the Service menu.EXITING SERVICE MODEAfter completing the changes, exit service mode by turning off the set using the Remote Commander or the power switch.NOTE: After exiting service mode wait 2 minutes before restarting the set to allow the fans to shut down properly.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201014SECTION 1:DISASSEMBLY1-1.OVERVIEWThe connectors in the MIX5 chassis have been redesigned to ensure they are securely fasten to the boards. Please review the illustrations below.TOOLS NEEDEDLong Phillips ScrewdriverNeedle Nose PliersSmall Flathead Screwdriver or Jewelers ScrewdriverLIFT ONE SIDE AT A TIME BY PUSHING TAB IN WITH SMALL SCREWDRIVERTYPE1TYPE2SQUEEZE DOWN ON TAB TO RELEASESQUEEZE LOCKING TAB TOWARDS CONNECTOR BEFORE PULLING FREETYPE3CAUTION! IF THE TYPE 2 FEMALE CONNECTOR HAS A SLOT (AS SHOWN) MAKE SURE THE LOCK TAB SEATS INSIDE THIS SLOT.Use caution not to rock the Type 2 or Type 3 connectors when removing or reinstalling to avoid breaking the solder leads off the Printed Circuit Boards. KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010153Lamp door121-2.REAR COVER REMOVALLamp doorTurn the handle until it is in the CLOSE positionLamp doorWhen reassembling the rear cover, be sure to securely lock the lamp door to avoid a lamp cover failure warning. 1Pull down the claw to release the Lamp Door2Remove the Lamp Door3Remove 13 screws (+BVTP2 4X16) to remove the Rear CoverKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010161-3.CHASSIS REMOVAL AND SERVICE POSITION3142567891Remove 2 screws to release the Left Stay2Disconnect CN8400 from U Board3Disconnect CN2500 from K Board4Release wires from purse locks5Gently pull chassis out towards the right of the TV to access connectors on B Block Assembly.6Disconnect CN308 and CN3750 on B Block Assembly7Release connectors from Wire Holders8Remove 4 screws to release the G Board9Remove 6 screws to detach Metal Shield from G BoardUsing the picture above as a reference, disconnect CN6018, CN6801, CN6804, CN6803, CN6800, CN6805, CN6900, CN6901, CN6009, CN6002, CN6904, and CN6010.1-4.G BOARD REMOVALKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010171-5.B BLOCK ASSEMBLY, A BLOCK ASSEMBLY, ANTENNA, U BOARD AND K BOARD REMOVAL1Remove 6 screws and 2 hexagon washers to release the Terminal Bracket from the U Board.On the U Board, disconnect CN8400 then using a at head screw driver gently release the CN3006 connector from the B Board to remove the U Board.2Disconnect the coaxial cable to release the antenna switch. Remove 3 screws then gently lift the A Block Assembly up to disconnect CN1002 from the B Block Assembly.3Using caution remove the LVDS cable from the B Board, then remove 1 screw (connecting the B Block Assy & K Board to the Main Bracket) and lift up on the tab of the Main Bracket to release the B Block Assembly.4Using tweezers gently pinch the fan dampers to release the fan. 5On the K Board, disconnect CN2502 then remove 1 screw to release the K Board. Gently pull the K Board out of the Main Bracket.25413A Block AssemblyLVDS ConnectionB Block AssemblyU BoardK BoardKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010180111-6.LAMP BLOCK ASSEMBLY AND OPTICAL BLOCK REMOVAL89562341Note: Remove the Lamp door and Lamp before removing the Lamp Block Assembly(See Replacing the Lamp in the Appendix section of this service manual.) S2 BoardT1Board71Remove 2 screws to release the Right Stay.2Disconnect CN150 T1 Board3Disconnect CN155 T2 Board4Disconnect the Termal Fuse connector.5Disconnect CN160 S2 Board6Remove 2 screws then pull out the fan cover.7Turn the fan cover over to remove the T1 Board and S2 Board.8Using caution remove the LVDS cable and 2 screws.9Remove 2 screws to release the Lamp Block Assembly and the Optical Block assembly from the cabinet.0Gently pull the Lamp Block Assembly and the Optical Block Assembly out of the cabinet.11Turn the assemblies around 180 degrees and release the high voltage lead from the purse lock.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201019231-6-1.LAMP CONNECTOR AND T2 BOARD REMOVAL1Pull retaining clip outward to release and drop the high voltage connector and the T2 Bracket.2Separate the HV Connector from the bracket3Remove 1 screw to release the T2 Board.11KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201020Lamp duct coverNote position of wiresNote: Watch forfan grommetsNOTE: Reinsert the fan grommets when replacing the fan2345611From the inside of the assembly, release the 3 claws securing the fan duct, then remove the fan duct by grasping as shown.2Remove 1 screw.3Release 3 clips to detach cover.4Remove Fan. 5Release wire from wire holders.6Remove 2 screws.1-6-2.LAMP DRIVER FAN REMOVALKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010211-7.HC BOARD REMOVAL1Remove 2 screws to detach the H2 Bracket.2Disconnect connector.3Remove 2 screws.4Lift out to remove HC Board.1431-8.HA BOARD AND HB BOARD REMOVAL4352HA BoardHB Board11Remove 2 screws from inside the front panel.2Using a screwdriver, gently push through the hole to release the speaker grill.3Firmly pull on the speaker grill to detach from the cabinet.4Disconnect CN7000 and remove 2 screws to release the HA Board5Disconnect CN7020 and remove 2 screws to release the HB BoardKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010221231-9. SCREEN FRAME ASSEBMLY AND SPEAKER REMOVALCAUTION:When removing the Screen Frame Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles.541Release the wire harness from the purse locks.2Disconnect the CN2500 from the K Board.3Remove 15 screws to detach the Mirror Cover Assembly from the Screen Frame Assembly.4Remove 4 screws to detach the Screen Frame Assembly from the front bezel.5Gently pull the Screen Frame Assembly forward.6Remove 20 screws from the screen frame to release the disfussion plates. Be sure to keep the retaining brackets.7To remove the speakers, remove 2 screws and release the speaker wires.677KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010231-10. MIRROR ASSEMBLY AND MIRROR COVER ASSEMBLY REMOVAL43211Remove 4 screws to release the 2 top mirror brackets.2Remove 3 screws to release the mirror holders (46 & 50 models only)3Using caution gently lift the mirror up and out of the mirror cover. (Slide the mirror up and to one side on the 55 model to release it from the mirror holders.)4Remove 4 screws to detach the front of the Mirror Cover Assembly from the cabinet. 5Remove 2 screws from back of the cover and then lift the Mirror Cover Assembly off of the cabinet.5CAUTION:When removing the Mirror Cover Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201024 WIRE DRESSINGTop LeadBottomLeadDress Lamp Driver Leads as shownbelow to wire holders.After Installing Duct Block assy toOptical Block Dress TOP Lamp Leadto Purse Lock on [C] Shield1-910-024-31 Connector Assy should bedressed around Heat Sink and around DuctBlock Cover as shown above.Dress "Bottom" Lamp Driver Lead asshown to wire holder on Duct Block AssyBALLAST WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201025 1-910-024-31 Connector Assy should bedressed around Heat Sink and around DuctBlock Cover as shown above.BALLAST WIRE DRESSING (CONTINUED)KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201026 Before installing chassisDress CN3004[B],CN8400[U], and CN3008[B]to purse lock on bottomblock as shown.Loop Video 2 Connectorbefore installing into PurseLock as shown to avoidConnector assy fromTouching [K] Board HeatSink.ONLY FOR 46" and 50"modelsInstall Ferrite Clamp154383011 to the followingConnector Assys1. Speaker Conn Assy2. HA/HB Conn Assy3. HC Conn AssyBOTTOM BLOCK WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201027 Install Conn Assy 1-910-024-21 to "FAN1"Optical Block Fan.Dress 15P CN9000 [C]LVDS Connector and FanConnector to Purse Lockon [C] ShieldRoute Optical Block Fanto Wire Holder to avoidbeing Pinched when [G]Shield is installedC BLOCK WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201028 Dress [B] Block Fan and [K] Board Connector Assy to PurseLock on [B] Block as shown above.CHASSIS WIRE DRESSINGDress the followingConnector Assys toPurse Lock on Duct BlockAssy :1. CN150 [T1]2. X1 (Ballast)3. X2 (Ballast)Note:Duct Block Fan is notinstalled to Purse LockDress the followingConnector Assys to WireHolder on Bottom Block:1. 1-910-024-292. X1 (Ballast)3. X2 (Ballast)4. Duct Block Assy Fan5. Optical Block FanRoute Lamp Faninside of 1-910-024-29and Inside of X2 (BallastPower)DUCT BLOCK ASSEMBLY WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201029 G-Board Wire Pin Holders Instructions.There are (3)wire pin Holders on the [G] board.See below to seewhich wires are dressed to each wire pin holder1.LVDS and 8P CN6009[G]2. LVDS, 8P CN6009, and 7P CN3004[B]3. LVDS and 7P CN3004[B]Ensure wires are dressed to the side of the G Boardas shown.312G BOARD WIRE DRESSINGInstall Purse Lock404928101 PURSE LOCK (DIA.11)Purse lock should hold the following:32P Conn Assy [G] to [B]3P Conn Assy [G] to [K]3P Conn Assy [G] to ANT SWT3P Conn Assy [G] to B-Blk FANAfter installing Purse Lock ensure open end isfacing towards the front of the set.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201030 OPTICAL BLOCK ASSEMBLY WIRE DRESSINGROUTE IRS CONNECTOR AS SHOWN APPLY HIMELONE TAPE AS SHOWN ABOVE AND DRESS IRIS CONNECTOR ASSY TO WIRE HOLDER AS SHOWN BELOWAPPLY HIMELONE TAPE TO SECURE IRIS CON-NECTOR AS SHOWN ABOVE.APPLY TAPE SO THAT THE CONNECTOR ASSEM-BLY WILL NOT BE IN SHADED AREA ABOVE.IF CONNECTOR ASSEMBLY IS IN THE SHADED ARER IT WILL GET PINCHED BETWEEN THE OPTICAL BLOCK ASSEMBLY AND THE BOTTOM BLOCK ASSEMBLY WHEN INSTALLED.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201031 x Secure Ring Terminal of1-910-016-90 to G-Block as shown above.x Install Faston Terminal to Antenna Switch.Note: Orientation of ring terminal should be towards the top of the set.1-910-016-90OPTICAL BLOCK ASSEMBLY LIGHTNING GROUND POSITIONKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201032 For 55, MUST use 2 screws on each side (total 4 screws) to secure Speaker Grill to Screen Frame.For 50 and 46 use only 1 screws each side (total 2 screws)SPEAKER GRILL WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201033 See above for Connector Assy Routing of CN110 [HB]See above forConnector Assy Routing of CN100 [HA]SPEAKER GRILL WIRE DRESSING (CONTINUED)KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201034 SPEAKER GRILL WIRE DRESSING (CONTINUED)Dress HA/HB Connector Assy to Wire holder as shown above.When routing HA/HB Connector Assy through Wire HolderRED tape should be approximately in the position shownabove.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201035 SPEAKER GRILL WIRE DRESSING (CONTINUED)1) Use Holder (M3), Wire 2-screw to wire dress as sh2) Wire must enter from the Holder 2-599-956-01 as s3) Must pull wire to the rightfrom wire assy (around Cand Cable Holder area)123NO Sound Cushion on 55 and 46 Speaker Grill-594-860-01 and 3x12howne bottom of Cable shownt to minimize sound vibControl Tray Bracket KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201036 SPEAKER GRILL ASSEMBLY CUSHIONSAdd 2-638-237-02 Cushion, Sound (SF) to 55 Speaker Grill 2-671-852-Align Sound (SF)Cushion to the lines as shownKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201037 aDress Positive Tab of Speaker wire around speaker bracketand then Himelon Tape should be installed to secure the wireas shown.Wire Should be pulled so that there is no excess wire.THIS IS VERY IMPORTANT TO AVOID NOISE DUE TOSPEAKER VIBRATIONTape should wrap around bracket as shown to the right andsecurely hold the speaker wire so that it does not move oncethe tape is applied.SPEAKER WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201038 1 23 4Speaker Bracket must be secured following the above ScrewOrder.On Left Speaker Secure Speakerwire as shown below using265206401 TAPE,HIMELON (20X40)Note:PCN MB607734 Shows different Tape positionplease disregard that location and use aboveSPEAKER WIRE DRESSING (CONTINUED)KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201039 RIGHT SPEAKER WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201040 LEFT SPEAKER WIRE DRESSINGKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201041 All these applies for 55, 46For 50, this starts from MP set #1 (no need to re-work PP and PVT sets)LEFT SPEAKER WIRE DRESSING (CONTINUED)KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201042CAUTION POINTSApply tape on B-Shield to keep LVDS Connector Assy and 7P CN3004 Connector on [B] from being "pinched" when Chassis is installed into Bottom BlockHimelon Tape should secure the (2) connectors coming from the Ballast, the Fan connector assy and 3P Connector Assy from T1ONLY FOR 50" MODELSHimelon Tape should secure Duct Block Assy fan Connector as shownConnector Assy should be pulled tight against fan Duct in order to avoid vibration of wire against bracket.BOTTOM BLOCK ASSEMBLY HIMELON TAPE LOCATIONKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201043After dressing Speaker Wire, HA/HB Connector Assy and HC Connector assy to Bottom Block.REMOVE as much excess slack in wires and dress to Purse Lock.Loop Video 2 Connector before installing into Purse Locak as shown to avoid Connector assy from Touching [K] Board Heat Sink.ONLY FOR 46" and 50" models Ensure no excess wire is hanging loose in this area.THIS IS VERY IMPORTANT TO AVOID NOISE DUE TO SPEAKER VIBRATIONBefore installing chassis Dress CN3004[B], CN8400[U], and CN3008[B] to purse lock on bottom block as shown.BOTTOM BLOCK WIRE DRESSING CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201044-Install Angled Purse Lock to C Shield as shown to the right.-Dress 15P connector Assy, LVDS ConnectorAssy and Optical Block Fan Connector Assy to Purse Lock as shown.435591211PURSE LOCK (DIA. 11)265206401TAPE, HIMELON (20X40)-Apply Himelon to [K] Board Power Connector Assy and tape to B Shield as shown.-Tape must be placed in this position to avoid connector from being pinched by [U] bracket when installed.CHASSIS WIRE DRESSING CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201045When Pulling the damper through the fan be careful not to use excessive force which may break the damper in this area269304701GASKET(5 X 10 X 30)DAMPER AND GASKET CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201046G-Board Wire Pin Holders Instructions.There are (3) wire pin Holders on the [G] board.See below to see which wires are dressed to each wire pin holder1.LVDS and 8P CN6009[G]2. LVDS, 8P CN6009, and7P CN3004[B]3. LVDS and 7P CN3004[B]123When Dressing 1-910-024-29 and Duct Block Fan to wire Holder ensure the wires are not positioned above capacitors on [G].This is to avoid the connector wires from touching the rear cover.Install Purse Lock 404928101 PURSE LOCK (DIA.11)Purselock should hold the following:32P Conn Assy [G] to [B]3P Conn Assy [G] to [K]3P Conn Assy [G] to ANT SWT3P Conn Assy [G] to B-Blk FANG BOARD WIRE DRESSING CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201047Dress Positive Tab of Speaker wire around speaker bracket and then Himelon Tape should be installed to secure the wire as shown.Wire Should be pulled so that there is no excess wire.THIS IS VERY IMPORTANT TO AVOID NOISE DUE TO SPEAKER VIBRATIONTape should wrap around bracket as shown to the right and securely hold the speaker wire so that it does not move once the tape is applied.RIGHT SPEAKER WIRE DRESSING CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201048Apply Himelon tape to speaker wire as shown to the left.Speaker wire must be placed inside Grooved slot in speaker and then secured with Himelon Tape.Before applying tape ensure asmuch slack is taken out of the wire by pulling it towards the negative terminal.Wire Holder is installed on speaker bracket as shown.Remove as much slack out of wire before dressing it to the wire holder. ONLY FOR 50" MODELSPull wire in direction of arrow to take out slack265206401 TAPE,HIMELON (20X40)After dressing to wire holder dress wire through speaker bracket as shown to the left.LEFT SPEAKER WIRE DRESSING CAUTION POINTSKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010492-1.USING THE REMOTE COMMANDER FOR ELECTRICAL ADJUSTMENTSTo adjust various set features, use the Remote Commander to put the set into service mode to display the service menus and categories.Equipment Needed:Pattern Generator (with component outputs)OscilloscopeDigital multimeter2-2.ACCESSING SERVICE ADJUSTMENT MODE1.TV must be in standby mode. (Power off).2.Press the following buttons on the Remote Commander within a second of each other: DISPLAY Channel 5 Volume+POWER.ENTNRUTERSLOOTTV/VIDEODVR/VCR SAT/CABLEFUNCTIONTV BD/DVDPOWERTV POWERJUMP ANT FREEZESOUND PICTURE WIDEVISUAL SEARCH PAUSEPLAYSTOPREC REC PAUSE REC STOPTOP MENUMENU F1 F2GD IUEDIPSYALREPLAY ADVANCE NEXT PREVTVCH VOLMENUMUTINGBD/DVDMODESLEEPSURROUNDDisplaysService MenusDISPLAYVOLUME (+)POWERJUMPRM-YD010The rst service menu (TV) displays.SECTION 2:CIRCUIT ADJUSTMENTS2-3.VIEWING THE SERVICE MENUSUse the Remote Commander to view the 3 service menus options.1.To display the Service Menu that contains the Category you want to adjust, press JUMP on the Remote Commander. (For a complete list of the service Categories refer to Service Menus)PressJUMPQ BoxTVPressJUMPVERSION0 0 SERVICEVERS Wide ZoomVideo 1WSL:480IQM0 0 SERVICEINFO DTVSample TV Service MenuKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010502-4.USING THE REMOTE COMMANDER TO CHANGE SERVICE DATAUse the buttons on the Remote Commander to access the service menu items and adjust the data values.ServiceMenuCategoryAdjustmentItemItem NumberData ValueVERSION0 0 SERVICEVERS Wide ZoomVideo 1WSL:480IF/A:0000000000000000CBA:00000000000000001.Access Service Adjustment Mode and select the Service Menu that contains the Category with the Adjustment Item you want to change.2.To change the Category, press2 or5 on the Remote Commander.Note: Pressing2 or5 only changes the categories within the Service Menu displayed. To change a Category on one of the other Service Menus, press the JUMP button until the correct Service Menu is displayed.3.To change the Adjustment Item, press 1 or 4 on the Remote Commander.4.To change the Data Value, press3 or6 on the Remote Commander.Note: To go back to the last saved Data Value, press0 thenENTon the Remote Commander to read the memory.5.To save the changes, pressMUTINGthenENTto write into memory.6.To exit service mode, turn the power off by pressingPOWER .Wait 2 minutes before restarting the set to allow the fans to completely shut down or the Service Menu will appear on the screen.ENTNRUTERSLOOTTV/VIDEODVR/VCR SAT/CABLEFUNCTIONTV BD/DVDPOWER TV POWERJUMP ANT FREEZESOUND PICTURE WIDEVISUAL SEARCH PAUSEPLAYSTOPREC REC PAUSE REC STOPTOP MENU MENU F1 F2GD IUEDIPSYALREPLAY ADVANCE NEXT PREVTVCH VOLMENUMUTINGBD/DVDMODESLEEPSURROUND6035124IncreaseData ValueDecreaseData ValueDisplayPrevious CategoryDisplayNext CategoryDisplayPrevious ItemDisplayNext ItemDisplaysService MenusMUTINGJUMPENTReads data from last saved NVMWrites data into memoryRM-YD010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201051SERVICE MENUS (CATEGORIES ONLY)TV MICRO TV MICRO (cont.) Q BOXVERSION IRIS_DBC QMID IRIS_ADJ QTNVM_SEL IRIS_UFOFSMODEL IRIS_WBOFSOSD IRIS_SCSBCCD IRIS_FIXEDCCT DSP_STEPOPTIONS DSP_SURRCXA2229Q DSP_MIXRUSER_NR DSP_AGCLPF_1 DSP_BTSNNR DSP_BBESNSS DSP_DRCCCPM_1 DSP_BQCCPM_2 FAN_CTRLCCPM_3 TEMP_SRVCCPM_4 TEMP_BRTOCCPM_5 PAWN_3DGCCPM_6 PAWN_SYSCCPM_7 PAWN_CAPCCPM_8 PAWN_MUTCCPM_9 PAWN_PICCCPM_10 PAWN_BLKCCPM_11 PAWN_WBOCCPM_12 PAWN_TSPHELIOS_1 PAWN_CURHELIOS_2 PAWN_TIMHELIOS_3 PAWN_HPFHELIOS_4 IRIS_APLHELIOS_5 TIMESCREEN IMG_SHIFTDCP_INT HDMIDCP_OSDDCP_BLKDCP_ADJ1DCP_ADJ2DCP_USERDCP_AVPA7001RA7001GA7001BA7007RA7007GA7007BA7007RGB2-4-1.EXITING SERVICE MODEAfter completing the changes, exit service mode by turning off the set using the Remote Commander or the power switch.NOTE: After exiting service mode wait 2 minutes before restarting the set to allow the fans to shut down properly.2-5.VERIFYING SERVICE DATA CHANGES1.After completing all adjustments turn the set off with the Remote Commander and WAIT for the fans to turn off before proceeding to the next step. Note: It may take up to two minutes for the fans to stop.Caution: To avoid over heating the lamp, do not unplug the set until the fans have stopped.2.After the fans have stopped, unplug the set from the AC outlet, then plug the set back in the AC outlet.3.To verify the changes repeat steps 1 through 3 of 2-4. Using the Remote Commander to Change Service Data.4.To exit service mode, turn the power off by pressingPOWER .Wait 2 minutes before restarting the set to allow the fans to completely shut down or the Service Menu will appear on the screen.NOTE: After exiting service mode wait 2 minutes before restarting the set to allow the fans to shut down properly.2-6.RESETTING WEGA (USER) MENU TO FACTORY DEFAULTSUse the following instructions to restore the User Controls and Channel Memory settings to the preset factory conditions.1.Turn the TV on by pressPOWER on the Remote Commander.2.While holding down the on the Remote Commander, press the POWER button on the Front Panel of the set.The set restarts and displays the initial setup screen. This may take several minutes.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010522-7.H/V CENTER CONFIRMATION AND ADJUSTMENTSUse the following instructions to adjust the pictures horizontal and vertical center after replacing either of the following:Optical Block AssemblyMirror Cover1.Set the signal to RF Monoscope, check the H/V center in Full picture mode.2.If the center is shifted, adjust the Horizontal and/or Vertical settings.a.Access Service Adjustment Mode.b.Press2 until the HELIOS_3 category displays.c.To adjust the Horizontal setting, press 1 until the DHPS (22) item displays.d.Press3 to increase the data value, or6 to decrease the data value.e.To adjust the Vertical setting, press 1 to display the DVPS (23) item.f.Press3 to increase the data value, or6 to decrease the data value.g.To save the changes, pressMUTINGthenENTto write into memory.h.To exit service mode, turn the power off by pressingPOWER .Wait 2 minutes before restarting the set to allow the fans to completely shut down or the Service Menu will appear on the screen.KDHPS 22(for H center)DVPS 23(for V center)DVPS DHPS2-8.IRIS ADJUSTMENTSUse the following instructions to adjust the IRIS after replacing either of the following:Optical Block Assembly B Block Assembly1.Access Service Adjustment Mode.2.Press2 until the IRIS_ADJ category displays.3.Press 1 until the AUTO (7) item displays.4.Press3 to change the data value to 1.5.Wait approximately 5 seconds until the data value is reset to 0.6.To exit service mode, turn the power off by pressingPOWER .Wait 2 minutes before restarting the set to allow the fans to completely shut down or the Service Menu will appear on the screen.KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201053SECTION 3:DIAGRAMS3-1.CIRCUIT BOARDS LOCATION3-2.PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS INFORMATIONAll capacitors are in F unless otherwise noted. pF : F 50WV or less are not indicated except for electrolytics and tantalums.All electrolytics are in 50V unless otherwise specied.All resistors are in ohms.k=1000, M=1000kIndication of resistance, which does not have one for rating electrical power, is as follows:Pitch : 5mm Rating electrical power : 1/ 4 W1/ 4 W in resistance, 1/10 W and 1/16 W in chip resistance.: nonammable resistor : fusible resistor : internal component : panel designation and adjustment for repair : earth ground : earth-chassisAll variable and adjustable resistors have characteristic curve B, unless otherwise noted.Readings are taken with a color-bar signal input.Readings are taken with a 10M digital multimeter.Voltages are DC with respect to ground unless otherwise noted.Voltage variations may be noted due to normal production tolerances.All voltages are in V.S : Measurement impossibility.: B+line.: B-line.(Actual measured value may be different).: signal path. (RF)Circled numbers are waveform references.The components identied by shading and ! symbol are critical for safety. Replace only with part number specied. The symbol indicates a fast operating fuse and is displayed on the component side of the board. Replace only with fuse of the same rating as marked.Les composants identies per un trame et une marque ! sont critiques pour la securite.Ne les remplacer que par une piece portant le numero specie.Le symbole indique une fusible a action rapide. Doit etre remplace par une fusible de meme yaleur, comme maque.T1S2HCAHAT2HBPowerSupplyBlockCBUGKThe C Board is part of the Optics Unit Block Assemblyand cannot be ordered separatelyKDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E201054REFERENCE INFORMATION RESISTOR : RN METAL FILM: RCSOLID: FPRDNONFLAMMABLE CARBON: FUSENONFLAMMABLE FUSIBLE: RWNONFLAMMABLE WIREWOUND: RSNONFLAMMABLE METAL OXIDE: RBNONFLAMMABLE CEMENT:ADJUSTMENT RESISTORCOIL : LF-8LMICRO INDUCTORCAPACITOR: TATANTALUM: PSSTYROL: PPPOLYPROPYLENE: PTMYLAR: MPSMETALIZED POLYESTER: MPPMETALIZED POLYPROPYLENE: ALBBIPOLAR: ALTHIGH TEMPERATURE: ALRHIGH RIPPLEGDSB1E1 C2B2 C1 E2234567890qaqsqfqhqjqk1GDSB2E2 C1B1 C2 E1B2E2 C1B1 C2 E1B2E2 C1B1 C2 E1qlB1E1 E2C1(B2) C2w;B1 E2C1 C2wswd(B2) E1(B2) E1E2 B1C2 C1waB1E1C2B2C1E2GS SDGDB1E1C2B2C1E2B1E2C2 C1(B2)E2B1C1C2 E1(B2)C2B1C1E2 E1(B2)C2B1C1E2B2E1C2Ver.1.5Transistor (FET)TransistorTransistorTransistorTransistorTransistorTransistorTransistorTransistorTransistorDiscrete semiconductot(Chip semiconductors that are not actually used are included.)DiodeDiodeDiodeDiodeDiodeDiodeDiodeDiodeDiodeDiodeSourceSourceAnode Anode(NC)(NC)CathodeAnodeCathodeCommonCathode CathodeCommonCathode CathodeCommonCommonCommonCommonCathodeAnodeBase EmitterCollectorBase EmitterCollectorDrainGateGateDrainDevice Printed symbol Terminal name CircuitTerminal name of semiconductors in silk screen printed circuit ()AnodeAnodeAnode CathodeAnode AnodeCathodeqdTransistor (FET)Transistor (FET)qgEmitterCollectorBaseTransistorSourceGateDrainCathodeAnodeAnodeCathodeAnodeAnode*55 KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20103-3.SIGNAL FLOW BLOCK DIAGRAMFY06 LA4 GW Signal FlowAIRANTSWCABLEBus I/FTunerDemod.NTSC/BTSCBus SWATi XILLEONx240HNANDFlash128MbSerialFlash1MbBIFVideoSWCXA2229RAudioSWCXA2188UAudioDACSPEAKER(L: 12W)SPEAKER(R: 12W)Audio DSPCXD9835Opt AudioCCPXACXD3814TV MicroSaiphHDMIMicroHDMI RxSiI9023SDRAM64MbHeliosCXD3808SDRAM64MbDCPCXD9690LVDSTxR LCDA7001PAWNCXD9809G LCDA7001B LCDA7001NVM256kNVM32kCEDID2kEDID2kAudioADCAudio OUTLinear AMPTA8258NVM128kAAudioDACGCXA1875I2SGraphicsLPFSM5302TMP75(FAN)TMP75(LAMP)S2HBLVDSRxAPLIRIS6568bit+syncYPbPr/RGBAudio SWCD4052FANS/VIDEO1VIDEO3COMP1COMP3AUDIO4For DVIVIDEO2COMP2KHCDeMUXFLIPFLOPMUX 24bit RGB13bitHDMI2 HDMI1Digital VideoAnalog VideoDigital AudioAnalog AudioDigital VideoMemoryControlUART-TVBus Level Shift5V 3.3VI2C-TV0I2C-TV1I2C-ADSP0Bus Level Shift5V 3.3VI2C-E0 I2C-E1Bus Level Shift3.3V 5VI2C-E11 11BUS ConnectorUART-JIGDDR256Mb*2DDR256Mb*2NVM64k 56 KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E20101|2|3|4|5|6|7|8|9|10|11|12|13|14|15|16|17|18|19|20|21|22| ABCDEFGHIJKLMNOPA BOARD SCHEMATIC DIAGRAM3-4.SCHEMATICS AND SUPPORTING INFORMATIONCHIP0 R1003CHIP0 R1004CHIP0 R1005CHIP0 R10061/10W RN-CP 5%1k R10071/10W RN-CP 5%1k R10081/10W RN-CP 5%1k R10091/10W RN-CP 5%1k R10101/10W RN-CP 5%2. 2k R10131/10W RN-CP 5%2. 2k R10140uHFB10000uHL100010V 100 C1000321610V 4. 7BC1001160816V 0. 1BC1002160816V 0. 1BC100316V 47 C10041/10W RN-CP 5%22kR101522uH L100116V 47 C1005160850V 0. 022FC10061.2mHL1002160850V 0. 022FC1007123 456TK11819MTLI C10001/10W RN-CP 5%1k R101650V 4. 7 C10081/10W RN-CP 5%100k R1017201250V 0. 1FC100950V 4. 7 C101022uH L10031/10W RN-CP 5%1kR1018CHIP0R1019321616V 4. 7BC1011160816V 0. 1BC10121/10W RN-CP 5%100R102154 321MIC5235YM5TRI C10011/10W RN-CP 0.5%470k R10221/10W RN-CP 0.5%68kR10231/10W RN-CP 0.5%6. 8k R1024321616V 4. 7BC1013160816V 0. 1BC1014UDZSTE-1710BD10000uHFB10010uHFB10020uHFB10030uHFB100410uHL100416V 100 C1015321616V 4. 7BC1016160825V 0. 1FC1017160816V 0. 1BC10182SA1235TP-1EFQ100010uHL100516V 47 C1019160825V 0. 01BC102010uHL1006160825V 0. 01BC1022160825V 0. 1FC1023CHIP0 R103150V 4. 7 C1025160850V 1000pBC102710V 470 C1028160825V 0. 01BC1029160850V 1000pBC10300uHFB10050uHFB10061/10W RN-CP 5%100 R10322SC3052EF-T1-LEFQ10011/10W RN-CP 5%15k R1033201210V 2. 2BC1032160850V 1000pBC10351/10W RN-CP 5%10k R1034160816V 0. 1BC10241/10W RN-CP 5%100 R1038CHIP0 R10392SA1235TP-1EFQ10022SC3052EF-T1-LEFQ10032SC3052EF-T1-LEFQ1004 16081/10W RN-CP 5%R1040 1001/10W RN-CP 5%100 R10411/10W RN-CP 5%1k R10421/10W RN-CP 5%1k R10431/10W RN-CP 5%1k R10441/10W RN-CP 5%470 R104510uHL10071/10W RN-CP 0.5%100k R1030ADRAGCINA5VI FOUTA32VD_I F1D_I F2AGNDAFT_OUTDET_OUTAGNDSAP_IDTU SDATUSCLA5V_VIFST_I DIF_AGCMODEF_MONOA9V_MPXR_OUTL_OUTTU10005V9V32V9V5V32V5V5V9V5V0uHFB10070uHFB10080uHFB1009160850V 33pCHC1036160850V 33pCHC1037160850V 33pCHC1038160850V 15pCHC1039160850V 15pCHC1040160850V 15pCHC1043160850V 15pCHC1044160850V 1pCKC1041160850V 1pCKC10421/10W RN-CP 5%10k R1047160850V 1000pBC10456. 3V 1000 C10211/10W RN-CP 5%22k R10121/10W RN-CP 5%22k R10111/10W RN-CP 5%1k R1025160850V 0. 022FC1026160850V 33pCHC10481234567891 01 11 21 31 41 51 61 71 81 92 02 12 222P CN1002BLKNTCS_LNTSC_R5. 1VSAP_ID10. 5VF_MONODET_OUTST_IDAFT_OUTGNDIF_AGCGNDGNDMODED_IF2GNDD_IF1GNDGNDAGC_MUTED_SCLD_SDA1608CHIPR1046 0A BoardTUNER9-883-709-01ATO B BOARDCN7802AGC-MUTEVIDEO-BUFFVIDEORLDC-DC CONV.LDO REGULATORINVERTERBUFFERBUFFERDue to the complexity of this board, performing component level eld repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. 57 KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010[TUNER]COMPONENT SIDEACN1000TU-BVTU-BLTU-BRGNDGNDGNDD1000IC1001C1010C1009L1003C1008IC100061C1013C1014R1022R1023C1005C1006R1017R1035R1036R1037C1015R1019R1020D1001L1001R1018R1021R1024C1007L1002R1016C1017C1011TU10002612 7 1C1012R1015L1004C1016C1020 L1005C1019FB1002FB1003FB1004Q1003Q1002R1040Q1004R1041R1042R1043FB1001R1038Q1000R1025R1039R1044R1045R1046C1023R1030C1018C1021361-AC1022R1031C1024C1003L1006A-1168-C1004C1046R1007R1011R1010R1014C1025FB1000C1002L1000R1008R1012222121CN10021-869-670-11(172753811)C1026C1027C1028C1001R1005C1047R1006C1000C1042C1043L1009R1004C1029C1030L1007C1041C1044 R1009R1013R1003C1032C1033C1045C1048Q1001R1033R1047C1037C1038C1040C1039FB1008L1008C1031FB1005R1026R1028R1032C1036FB1009FB1007C1034C1035FB1006R1027R1029R10341ABCDEF2 3 4 5 6 7[TUNER]CONDUCTOR SIDEAJL1019JL1014JL101826JL1015EPGWGN1-869-670-11(172753811)JL1007JL1013JL1010JL1012JL1009JL101112NTSC-L1NTSC-R2JL100812JL1016DET-OUT5.1V10.5VST-IDSAP-IDF-MONOJL10067GNDIF-AGCAFT-OUTJL1017 MODEGNDGNDJL1004GNDD-IF1D-IF2AGC-MUTEGNDGNDJL1003D-I2C-SCL21D-I2C-SDA22JL1000JL1001J L 1 0 0 2J L 1 0 0 5CN1002212211ABCDEF2 3 4 5 6 7 58KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010Due to the complexity of this board, performing component level eld repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. 1 |2|3 |4 |5 |6 |7 |8 |9 |10 |11 |12 |13 |14 |15 |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |ABCDEFGHIJKLMNOPB BOARD SCHEMATIC DIAGRAM (1 OF 11)160816V 0. 1BC300012160816V 0. 1BC300212160816V 0. 1BC300412160816V 0. 1BC300712160816V 0. 1BC30091 2160816V 0. 1BC30101 2160816V 0. 1BC30151 2160816V 0. 1BC302112160816V0.1C302212160816V 0. 1BC302612160816V 0. 1BC302712160816V 0. 1BC303112160816V 0. 1BC30321 2160816V 0. 1BC303312160816V 0. 1BC303712160816V 0. 1BC303912160816V0.1B C3042121608 16V 0. 1 C30441 2160816V 0. 1BC30451 2160816V 0. 1BC305012160816V 0. 1BC305912160816V 0. 1BC307712160816V 0. 1BC30781216V 100 C3035 1216V 100 C30651216V 100 C30661216V 100 C30791216V 100 C308212160825V 0. 022BC30751 26. 3V 47 C3006126. 3V 47 C300812160816V 0. 22BC302012160816V 0. 22BC302512160816V 0. 22BC30301210V 22 C30131210V 22 C30601210V 47 C30011210V 47 C30031210V 47 C305712160850V 15pCHC30471 2160850V 18pCHC30461 2160850V 82pCHC3034 12160850V 1000pBC3038 12160850V 1000pBC304312160850V 2200pBC307412160825V 0. 01BC300512160825V 0. 01BC301112160825V 0. 01BC301212160825V 0. 01BC303612160825V 0. 01BC305612160825V 0. 01BC306212160825V 0. 01BC306312160825V 0. 01BC308012160825V 0. 01BC308312160825V 0. 1FC3052121/10W10R3071121/10W10R3073121/10W10R3074121/10W10R3075121/10W10R3077121/10W10R3078121/10W 22 R30121 21/10W RN-CP 5%22 R31351 21/10W 47 R3029 1 21/10W 47 R30311 21/10W 47 R30341 21/10W 47 R3041 121/10W47R3067 121/10W47R3069121/10W RN-CP 5%47 R30871 21/10W47R3090121/10W RN-CP 5%47 R3100121/10W 47 R31221 21/10W 47 R31251 21/10W 47 R3126 1 21/10W 47 R31271 2 1/10W 47 R31281 2 1/10W 47 R31291 21/10W RN-CP 5% 47 R31301 21/10W 47 R3132 1 21/10W 47 R31331 21/10W RN-CP 5%47 R31371 21/10W 47 R31381 21/10W RN-CP 5%47 R3140 121/10W RN-CP 5%47 R3142121/10W 100 R30061 21/10W 100 R30251 21/10W 100 R30321 21/10W RN-CP 5%100 R3038 1 21/10W RN-CP 5%100 R3039 121/10W 100 R30421 21/10W 100 R30511 21/10W 100 R30571 21/10W RN-CP 5%100 R3080 121/10W RN-CP 5%100 R3098121/10W100R3099121/10W 100 R31021 2 1/10W 100 R31031 21/10W RN-CP 5%100 R3104121/10W100R3105121/10W 100 R31101 21/10W 100 R31111 21/10W100R3115121/10W 100 R31161 21/10W 100 R31191 21/10W 100 R31211 21/10W 100 R31241 21/10W RN-CP 5%100 R31311 21/10W RN-CP 5%100 R31341 21/10W 100 R31611 2 1/10W 100 R31621 21/10W 100 R31791 21/10W 100 R31801 21/10W100R3190121/10W RN-CP 5%100 R3191 121/10W100R3192121/10W 100 R34631 21/10W100R3464121/10W100R3491121/10W RN-CP 5%470 R3141121/10W 1k R30221 21/10W1kR3050121/10W1kR3058121/10W1kR3060121/10W1kR3065121/10W RN-CP 5%1k R3092121/10W RN-CP 5%1k R3095121/10W RN-CP 5%1k R3446 121/10W RN-CP 5%1k R34561 21/10W RN-CP 5%1k R3489 121/10W RN-CP 5%1. 5k R30181 21/10W RN-CP 5%1. 8k R3168 12 1/10W RN-CP 5%1. 8k R3170 121/10W RN-CP 5%1. 8k R3454 12 1/10W RN-CP 5%1. 8k R3455 121/10W RN-CP 5%2. 2k R30681 21/10W RN-CP 5%2. 2k R3081 121/10W RN-CP 5%2. 2k R3153 121/10W RN-CP 5%2. 2k R30081 21/10W RN-CP 5%3. 3k R3049 121/10W RN-CP 5%3. 3k R3056121/10W RN-CP 5%3. 3k R3064121/10W RN-CP 5%4. 7k R30051 21/10W RN-CP10k R30211 21/10W10k R3082121/10W RN-CP 5%10k R31011 21/10W RN-CP 5%10k R3106121/10W RN-CP 5%10k R3107121/10W 10k R3117 1 21/10W RN-CP 5%10k R31181 21/10W 10k R31201 21/10W RN-CP 5%10k R3143121/10W RN-CP 5%10k R3146121/10W RN-CP 5%10k R31501 21/10W RN-CP 5%10k R3164121/10W RN-CP 5%10k R3169 12 1/10W RN-CP 5%10k R3173 121/10W RN-CP 5%10k R3181121/10W RN-CP 5%10k R31851 21/10W RN-CP 5%10k R3186121/10W10kR3193121/10W RN-CP 5%10k R344512 1/10W RN-CP 5%10k R3448121/10W RN-CP 5%10k R3449121/10W RN-CP 5%10k R34571 21/10W RN-CP 5%10k R3462121/10W RN-CP 5%10k R3465121/10W RN-CP 5%10k R3470121/10W RN-CP 5%10k R3488121/10W RN-CP 5%10k R3011121/10W RN-CP 5%10k R30151 21/10W RN-CP 5%10k R3016121/10W RN-CP 5%15k R3070121/10W RN-CP 5%47k R3003 121/10W RN-CP 5%47k R3036121/10W RN-CP 5%47k R3151121/10W RN-CP 5%47k R31761 21/10W RN-CP 5%47k R31841 21/10W RN-CP56k R30725%121/10W RN-CP 5%470k R30021 21/10W RN-CP 5%1M R3066 121/10W RN-CP 5%1M R30131 21/10W RN-CP 5%2. 2M R313612CHI P0 R304012CHI P0 R304712CHI P0 R305412CHI P0 R305912CHI P0 R3062120 R3079120 R308512CHIP0R3089 12CHI P0 R31541 2CHI P0 R31571 2CHI P0 R3159 1 2CHI P0 R3160 1 2CHI P0 R317512CHI P0 R3177 1 2CHIP0R317812CHI P 0 R31951 2CHI P0 R31961 2CHI P0 R3197 12CHI P 0 R31991 2CHI P 0 R32001 2CHI P 0 R32011 2CHI P 0 R32021 2CHI P 0 R32031 2CHI P 0 R32041 2CHI P 0 R32271 2CHI P 0 R3254 1 2CHI P 0 R3255 1 20 R32571 20 R32591 20 R32621 20 R3281 1 20 R3282 1 2CHI P 0 R3310 1 2CHI P 0 R3328 1 2CHI P 0 R3330 1 2CHI P 0 R3336 1 2CHI P 0 R33611 2CHIP0R336212CHIP0R336312CHIP0R336412CHI P 0 R33661 2CHI P 0 R33671 2CHI P 0 R33681 2CHI P 0 R33891 2CHI P 0 R33921 2CHI P 0 R3393 1 2CHIP0R3394120R339512 0R3397120R339812 0R339912CHI P 0 R34361 2CHI P 0 R34381 2CHI P 0 R3442 1 2CHI P 0 R34471 2CHI P0 R345012CHI P0 R34511 21608CHI PR3452 01 21608CHI PR3453 01 2CHI P0 R34611 21608CHI PR3467 01 21608CHI PR3469 01 21608CHI PR3471 01 21608CHI PR3476 0 121608CHI PR3477 01 2CHIP0R348012CHIP0R348112CHIP0R348212CHIP0R348312CHIP0R348512CHI P 0 R34871 2CHI P0 R30231 2CHI P0 R301912CHI P0 R3020121/10W RN-CP510 R30485%121/10W RN-CP510 R30635%121/10W RN-CP100k R30355%1 210k RB30042 14 36 58 747 RB30012 14 36 58 747 RB30022 14 36 58 747 RB30032 14 36 58 747 RB3006 2 14 36 58 747 RB30072 14 36 58 7EMIG0uH FL 30021 23EMIG0uH FL 30031 23EMIG0uH FL 30041 2310uHL 30001 210uHL 30011 210uHL 30021 210uHL 30031 210uHL 30041 210uHL 30051 210uHL 30061 21 2 3 4 5 6 7 8 9 10 11BRN 11P CN3007SDA-E1SCL-E1JIG-TXDJIG-RXDE DTV-VOUT5V E B-INTSDA_TV1SCL_TV123 4132. 768kHz X300124 3148MHz X3000 12310. 135MHz X300212123456789101112131415161718192020P CN3006SCL-TV1SDA-TV1GNDA_5VCR/RCCB/BGNDCV/Y/PCHVY/GGNDA_9VTUNER_CVGNDLINE-E_MUTEVARFIXED-RVARFIXED-LGNDSWITCH_OUT_RSWITCH_OUT_LI OGNJU7223DL 1-18I C30001 2354 321BD4729GTRI C30031234RST5VCCMC2836D300312 3MC2836D3005123MC2836D301312 3MC2838-T112-1D30041 23MC2838-T112-1D3006123MC2838-T112-1D3007123MC2838-T112-1D30121 23UDZSTE-175.6BD300812UDZSTE-178.2BD310312UDZS-TE17-12BD3102122SC3052EF-T1-L EFQ3000 1232SC3052EF-T1-L EFQ3007 1232SC3052EF-T1-L EFQ30101232SC3052EF-T1-L EFQ30161232SC3052EF-T1-L EFQ30171232SC3052EF-T1-L EFQ3101 1232SC3052EF-T1-L EFQ31021232SC3052EF-T1-L EFQ30091232SA1235TP-1EFQ30011232SA1235TP-1EFQ30021232SA1235TP-1EFQ3003 1232SA1235TP-1EFQ3004 1232SA1235TP-1EFQ3011 1232SA1235TP-1EFQ30051235 43 2 1TAR5S33(TE85R)I C30011 2 34 5KEY1D5VSIRCS1/10W 100 R30331 2PWR_MUTEFAN_PROTFAN_CTRLI RI S_CTRLSP_MUTEAUDIO_MUTELINE_MUTELAMP_CTRLLAMP_COVERLAMP_PROTHV-DET1/10W 1. 5k R3028STBY_5V STBY _3.3VAUDIO_SW_CTRLSAIPH_OSDD3.3VDE_RSTATSC_RSTHDMI_RSTAP_PDAU_PDO_LVDS1_PDSAI PH-240 UARTI 2C-E 0AP_RSTMAIN_HMAIN_VD3.3VI 2C-ADSP0AGC_MUTE_SAIPHO_DCP_RSTO_HELIOS_RSTWP-CWP-LUTO_CCPX_RSTAC_RELAY 8 7 6 54 3 2 1M24128-BWMN6T(A)I C3005DATCLK WP$A0CHI P0 R34841 2D1G2S2 D2G1S1SSM6N15FU(TE85R)I C3004324 651I 2C-TV 0I 2C-TV 1D1G2S2 D2G1S1SSM6N15FU(TE85R)I C3623I 2C-E 1I 2C-E 0SP-E_MUTEAUDIO-E_MUTE10. 5VAUDIO_DSP_OUT1/10W RN-CP510 R30555%12IRIS_HALL_OUTI RI S_APLAFTKEY1B_I NTSIG_DET9VMAIN_Y/CV_SAIPHMAIN_HSTBY _3.3V10. 5V10. 5VSTBY _3.3VI 2C-E 0PWR_MUTEWP-CWP-LUTSTBY_5VFAN_PROTFAN_CTRLHV-DETLAMP_PROTLAMP_COVERAC_RELAYI 2C-E 19V10. 5VI 2C-E 1JIG_UARTD5VB_I NTCHI P 0 R31941 2AUDIO_DSP_OUTCXA2188_AUDIO_OUTTUNER_CVLINE_MUTEI 2C-TV 1D3.3VTUNER_CV_SAIPHSTBY_5VSI RCS1/10W RN-CP 5%4. 7k R30761 2TP3617TP3619TP3615 TP3614 TP3613 TP3612 TP3611TP3620TP3621TP3622TP3609TP3610TP3000TP3001TP3002TP3004TP3003TP3009TP3006TP3005TP3007TP3008DCP_CLK_TO_SAIPH20126. 3V 10BC3014121608100V 100pCHC3084121608100V 100pCHC3085121608100V 100pCHC30861/10W RN-CP220k R30945%121/10W RN-CP 5%47 R31981 2I 2C-E 10R3437120R343512 0R343412 0R3426120R3396121/10W RN-CP 5%1. 5k R3091 121234566P CN3005WHT1GND29V3A_MUTE4SP_MUTE5DSP_OUT_R6DSP_OUT_LAC_DET CHI P 0 R31081608CHI PR3354 01608CHI PR3359 0AC_DETLAMP_CTRLD5VD3.3V100 R31091 2CHI P0 R3007CHI P0 R3123 MAIN_CV2SC3052EF-T1-L EFQ30121/10W RN-CP 5%1k R30861/10W RN-CP 5%1k R3045MAIN_Y/CB/CRAC-OFF_MUTEMC2838-T112-1D30171234567891 01 11 21 31 41 51 61 71 82 01 92 12 22 32 42 52 62 72 82 93 03 13 2CN3002 32PSTBY_5VFAN_PROT/LVDS_PDGNDFAN_CTRL/POW_MUTEGNDHV_DET/DCP-VGNDE-MUTE/LAMP_CTRLGNDLAMP_PROT/DE_RSTGNDLAMP_COVER/B_INTGNDAC_RELAYGNDSCL-E1GNDSDA-E1GNDSDA-TV0GNDSCL-TV0/AC-DETGND3. 3V3. 3V3. 3V5V5V10. 5V9V10. 5V10. 5V12345677P CN3004PAWN_MUTEGNDSDA_ESCL_EWP_CWP_LUTGND1 2 3 4 5 6 7 8 9 10 11 12 13 14 1515P CN30085V GNDSDASCLP_ONSIRCSPOW_LEDSTBY_LEDLAMP_LEDP_MUTE_LEDTIMER_LEDGNDSTBY_3.3VGNDKEY1/10W RN-CP100 R3037I RI S_PEAK1/10W RN-CP 5%2. 2k R3145 121/10W RN-CP 5%2. 2k R3147 121 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176MB91F318RPMC-G-001E1I C30021OSD_H2MAIN_H3SUB_H43.3V5GND6VGS17CPO18VSSP19A2.5V(3.3V)10VGS211CPO212VSSP213A2.5V(3.3V)14VGC315CPO316VSSP317A2.5V(3.3V)18VDDR19VREF20VRO21ROUT22VSSR23VDDG24GOUT25VSSG26VDDB27BOUT28VSSB29DATASLICERMAIN30DATASLICERSUB31A2.5V(3.3V)32GND33L2.5V(1.8V)343.3V353.3V36GND37KEY138KEY239MAIN_AFT40I_IRIS_APL41I_IRIS_HALL_OUT42I_IRIS_PEAK43SIG_DET44BIINT45O_AC_RELAY46NVM_WP47O_CCPX_RST48O_WP_LUT49O_WP_C50APC_SW/BUSY351O_HELIOS_RST52O_DCP_RST53F_MONO54ANT_M55O_AGC_ATT563. 3V57MAIN_CLK_058GND59MAIN_CLK160L 2. 5V ( 1. 8V )61TRSTX62ICLK63IBREAK64I CS065I CS166I CS267ICD068ICD169ICD270ICD371MD072MD173MD274MD375RESET76SCL077SDA078I 2C-ADSP0/SCL-A079I 2C-ADSP0/SDA-A080SI 081SO082SCK083SI 184SO185SCK186SIRCS87CCD_M_H88CCD_M_V89MAIN_HIN90RESERVERD91WAKE923.3V93SUB_CLK_094GND95SUB_CLK_196L2.5V(1.8V)97V_SYNC98RESERVED99O_AUDIO_DSP_RST1003.3V101LAMP_SEL102I_IRIS_TRIG103PC_SYNC_DET104MPWRN105I2C-E0/SCL-E0106I2C-E0/SDA-E0107SCL3108SCL4109SDA3110SDA4111RXD_ATSC112TXD_ATSC113I_DIG_MDL114O_LVDS1_PD115O_AU_PD116O_AP_PD117POWER_LED118NC119TIMER_LED120STBY_LED121RESERVED122L2.5V(1.8V)123GND1243.3V125RESERVED126D_OVP127ATSC_OVP128NC129LB_ERROR130O_HDMI_RST131O_ATSC_RST132O_DE_RST133 O_PAWN_RST134 O_PWR_MUTE135 RESERVED136 USB_DET137 I_FAN_PROT138 O_AUDIO_SW_A139 O_AUDIO_SW_B140 O_FAN_CTRL141 O_IRIS_PPG_OUT142 RESERVED143 SP_MUTE144 AUDIO_TB145 AUDIO_MUTE146 LAMP_LED147 LINE_MUTE148O_LCDE_MUTE149O_LAMP_CTRL150 I_LAMP_COVER151I_LAMP_PROT152I_HV-DET153 I_AC_OFF_DET154L 2. 5V ( 1. 8V )155USB_CLK_1156 GND157USB_SLK_01583. 3V159UDM160UDP161D_B0162D_B1163D_B2164D_G0165D_G1166D_G2167D_R0168D_R1169D_R2170L 2. 5V ( 1. 8V )171YM_OUT172YS_OUT173FH174DPT_CLK_0175DOT_CLK_1176OSD_V1 2 3 44P CN3003 D+ D-GND5V-OUT1/10W 47 R31121/10W 47 R31131/10W 10k R31141/10W 10k R3139D3.3VI 2C-TU01 2 3 4 5 6 7 8 9 10 11 12 13 1414P CN30011UVCC2XTRST3XRSTIN4XINIT5BREAK6ICD37ICD28ICD19ICD010ICS211ICS112ICS013GND14ICLK1 2 3 4 5 6 7 88P CN30001STBY_3.3V2RESET3MD24BUSY35E6SI07SO08SCK0160850V 18pCHC304012160850V 15pCHC304112SDA-TV0SCL-TV0STBY_LEDTIMER_LEDPWR_LEDTIMER_LEDLAMP_LEDSTBY_LEDPWR_LEDLAMP_LEDSTBY _3.3VS_VBUSABS-B 1S-B 2S-G0S-G1S-G2S-R 0S-R 2S-R 1S-YMS-Y SS-B 0S_UDMS_UDPS_UDPS_VBUSTXDRXDSDA-E0SCL-E0SI0SO0SCK0SCK0SO0S I 0SDA-A0SCL-A0SDA-TV0SCL-TV0SDA-TV1 SDA-TV1SCL-TV1 SCL-TV1SCL -E1SDA-E1RLSDA-E1SCL -E1DIAG_RXDDIAG_TXD SCL-E1SDA-E1CXA2188_LCXA2188_RLRSCL-TV1SDA-TV1DSP_VSDSP_HSCSDA-E0 SDA-E0STVY 3.3VSCL-E1SDA-E1SDA-E0SCL -E0CV_YMAIN_CRMAIN_CBMAIN_YSTBY 1.8VS_UDMSDA-TU0SCL-TU0SCL -E0USB VERTICALTO USB-TVT oUpgradeT oE mmul atar( 3. 3V )i 5V _I 2C)i 5V _I 2C)TOC_BOARDJIG_CONNECTORTOHB BOARDTIMER_LED_IS_REVERSED_ON_HBP_ONTOU BOARDTOK_BOARDGNDTOG BOARDSAI PHLEVEL SHIFT OV P L OW-BSAI PHTOHA BOARD3. 3VR E G.1. 8VR E G.H- COUNTNVMRESETLEVEL SHIFT9-883-709-01B -1CN2502CN6904CN8403CN100CN110ANDCN9000B ( 1/ 11) 59KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010Due to the complexity of this board, performing component level eld repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. 1 |2|3 |4 |5 |6 |7 |8 |9 |10 |11 |12 |13 |14 |15 |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |ABCDEFGHIJKLMNOPB BOARD SCHEMATIC DIAGRAM (2 OF 11)160816V 0. 1BC320312160816V 0. 1BC321712 160816V0.1BC322012160816V0.1BC322112160816V0.1BC322212160816V 0. 1BC322512160816V 0. 1BC322712160816V 0. 1BC322812160816V 0. 1BC322912160816V 0. 1BC323112160816V 0. 1BC323212160816V 0. 1BC3238 1 2160816V 0. 1BC32391 2160816V 0. 1BC32401 2160816V 0. 1BC32411 21608 16V 0. 1 B C32421 2160816V 0. 1BC325512160816V 0. 1BC326112160816V 0. 1BC32641 2160816V 0. 1BC327112160816V 0. 1BC3296 12160816V 0. 1 C32981 216V 0. 1 C33001 2160816V 0. 1BC331212160816V 0. 1BC33131216V 100 C32691216V 10 C3224 1 216V 10 C32901 216V 10 C3291 1 216V 10 C32921 216V 10 C3293 126.3V 47 C3243 1 210V 22 C32721 210V 22 C32731 2160850V 15pCHC331412 160850V 15pCHC331612160850V 56pCHC332612160850V 1000pBC33151 2 160850V 1000pBC331712160850V 4700pBC326612160825V 0. 01BC320012160825V 0. 01BC320412160825V 0. 01BC320512160825V 0. 01BC320612160825V 0. 01BC320712160825V 0. 01BC320912160825V 0. 01BC321012160825V 0. 01BC321112160825V 0. 01BC321212160825V 0. 01BC321312160825V 0. 01BC321512160825V 0. 01BC3223121608 25V 0. 01 B C32351 2160825V 0. 01BC324612160825V 0. 01BC3249 1 2160825V 0. 01BC3250 1 21608 25V 0. 01BC32511 21608 25V 0. 01BC3252 1 2160825V 0. 01BC32531 2160825V 0. 01BC3256 12160825V 0. 01BC32591 2160825V 0. 01BC32601 2160825V 0. 01BC326312160825V 0. 01BC328012160825V 0. 01BC32811 2160825V 0. 01BC332212160810V 1BC321612160810V1BC321912160810V 1BC323312160810V 1BC32581 2 160810V 1BC32651 2160810V 1BC3285 12160810V 1BC32861 2160810V 1BC3287 1 2160810V 1BC32881 21/10W RN-CP 5%10 R3218121/10W RN-CP 5%10 R3219121/10W RN-CP 5%10 R3220121/10W RN-CP 5% 10 R32491 21/10W RN-CP 5%10 R32771 21/10W RN-CP 5%10 R33381 21/10W RN-CP 5%10 R33391 21/10W RN-CP 5%10 R33401 21/10W RN-CP 5%10 R33411 21/10W RN-CP 5%10 R33421 21/10W RN-CP 5%10 R33501 21/10W RN-CP 5%10 R33511 21/10W RN-CP 5%22 R3221 1 21/10W RN-CP 5%47 R3233121/10W RN-CP5% 47R323412 1/10W RN-CP 5%47 R3235121/10W RN-CP 5%47 R32981 21/10W RN-CP 5%47 R32991 21/10W RN-CP 5%47 R33081 21/10W RN-CP 5%47 R33131 21/10W RN-CP 5%47 R33141 21/10W RN-CP 5%47 R33151 21/10W RN-CP 5%47 R33161 21/10W RN-CP 5%47 R33171 21/10W RN-CP 5%47 R3382 121/10W RN-CP 5%100 R32691 21/10W RN-CP 5%150 R3263121/10W RN-CP 5%150 R3264121/10W RN-CP 5%220 R33861 21/10W RN-CP 5%330 R3265121/10W RN-CP 5%330 R3266121/10W RN-CP 5%470 R3347121/10W RN-CP 5%470 R3375 121/10W RN-CP 5%470 R3383 121/10W RN-CP 5%470 R3384 121/10W RN-CP 5%470 R3385 121/10W RN-CP 5%560 R33481 21/10W RN-CP 5%560 R33531 21/10W RN-CP 5%1k R3272121/10W RN-CP 5%1k R3273121/10W RN-CP 5%1k R3343121/10W RN-CP 5%1k R3344121/10W RN-CP 5%1k R3345121/10W RN-CP 5%1k R3346121/10W RN-CP 5%1. 5k R3300 121/10W RN-CP 5%2. 2k R3369121/10W RN-CP 5%2. 2k R3371121/10W RN-CP 5%2. 2k R3372121/10W RN-CP 5%2. 7k R32051 21/10W RN-CP 5%2. 7k R3223121/10W RN-CP 5%3. 3k R3376121/10W RN-CP 5%5. 6k R3373 121/10W RN-CP 5%5. 6k R3380 121/10W RN-CP 5%6. 8k R33781 21/10W RN-CP 5%10k R3209 1 21/10W RN-CP 5%10k R3215121/10W RN-CP 5%10k R3231121/10W RN-CP 5%10k R3240121/10W RN-CP 5%10k R32471 21/10W RN-CP 5%10k R3283 121/10W RN-CP 5%33k R328812CHIP0 R32061 2CHIP0 R321012 CHIP0 R3213 12CHIP0 R321412CHIP0 R321712CHIP0 R322212CHIP0 R323012CHIP0 R323212CHIP0 R323612CHIP0 R323712CHIP0 R323812CHIP0 R3241 1 2CHIP 0 R32421 2CHIP 0 R32431 2CHIP0 R32441 2CHIP0 R32741 2CHIP0 R327512CHIP0 R3280 12CHIP0 R328612CHIP0 R32921 2CHIP0 R3303 12CHIP0 R33491 2CHIP0 R33521 2CHIP0 R33701 2CHIP0 R337412CHIP 0R33791 2CHIP0 R338712CHIP0 R33901 2CHIP0 R33911 21/10W RN-CP 0.5%39 R3248 1 21/10W RN-CP 0.5%100 R3323 121/10W RN-CP 0.5%100 R3325 121/10W RN-CP 0.5%200 R32671 21/10W RN-CP 0.5%200 R32681 21/10W RN-CP 0.5%200 R3270 121/10W RN-CP 0.5%200 R3271 121/10W RN-CP330 R33110.5%121/10W RN-CP470 R32610.5%121/10W RN-CP 0.5%680 R3284121/10W RN-CP 0.5%680 R3293121/10W RN-CP 0.5%1k R3207121/10W RN-CP 0.5%1k R3260 121/10W RN-CP 0.5%1k R3312 121/10W RN-CP 0.5%1k R3322121/10W RN-CP 0.5%1k R3324121/10W RN-CP 0.5%1. 2k R3279 1 21/10W RN-CP 0.5%1. 2k R3294 121/10W RN-CP1. 8k R32850.5%1 21/10W RN-CP1. 8k R32910.5% 1 21/10W RN-CP1. 8k R33560.5%121/10W RN-CP4. 7k R32240.5%121/10W RN-CP4. 7k R32260.5%1 21/10W RN-CP 4. 7k R32450.5%1 21/10W RN-CP4. 7k R32510.5%1 21/10W RN-CP5. 1k R32080.5% 1210kRB32012143658710k RB32022143658710k RB32052143658710k RB3206 2143658710kRB32072143658710kRB32082143658710k RB32092143658710k RB32112143658747 RB32102143658747 RB32122143658747 RB32132143658747 RB32142143658747 RB3219 21436587100 RB32152 14 36 58 7100 RB32162 14 36 58 7100 RB32202 14 36 58 7100 RB32212 14 36 58 7EMIG0uHFL32001 23EMIG0uH FL32011 23EMIG0uH FL32021 23EMIG0uH FL32051 23EMIG0uH FL32061 231 2 34 6FL32071 2 34 61 2 34 6FL32081 2 34 61 2 34 6FL32031 2 34 61 2 34 6FL32041 2 34 610uH L32121210uH L32131 20uH FB3607121uH L32001 21uH L32011 21uH L32021 21uH L32031 21uH L32041 21uH L3205121uH L3206121uH L32071 21uH L32081 21uH L32091 21uH L32111 21uH L32141 210uH L32101210uH L3215 12CONT VDDOUT GND79.99188313MHz X320012 342SC5477-T122-1 Q3212 1232SC5477-T122-1 Q3213 1232SC5477-T122-1 Q32141232SC5477-T122-1 Q3219 1232SC5477-T122-1 Q3221123RT1A3906-T122-1Q3203123RT1A3906-T122-1Q3204 123RT1A3906-T122-1Q3205123RT1A3906-T122-1Q3209123RT1A3906-T122-1Q3217123RT1A3906-T122-1Q321812354 321PST3629NRIC3206123452SC3052EF-T1-LEF Q32011232SC3052EF-T1-LEF Q3210 1232SC3052EF-T1-LEF Q32111232SC3052EF-T1-LEF Q3220 1232SC3052EF-T1-LEF Q32231232SA1235TP-1EFQ3207 1232SA1235TP-1EFQ32081232SA1235TP-1EFQ3215 1232SA1235TP-1EFQ32161232SA1235TP-1EFQ3224123A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 R1 T1 U1 V1 W1 Y1 AA1AB1AB2AB3AB4AB5AB6AB7AB8AB9 AB10AB11AB12AB13AB14AB15AB16AB17AB18AB19AB20AB21AB22AA22 Y22W22 V22 U22 T22 R22 P22N22M22 L22 K22 J22H22 G22 F22 E22D22 C22 B22 A22 A21L2M2N2P2R2T2U2V2W2Y2AA2AA3AA4AA5AA6AA7AA8AA9AA10AA11AA12AA13AA14AA15AA16AA17AA18AA19AA20AA21Y21W21V21U21T21R21P21N21M21L21K21J21H3 J3 K3 L3 M3 N3 P3 R3 T3 U3 V3 W3 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 W20 V20 U20 T20 R20 P20 N20 M20 L20 K20 J20 H20 G20 F20 E20 D20 C20 C19 C18 C17 C16 C15 C14 C13 C12 C11 C10 C9 C8 C7 C6 C5 C4 D4 E4 F4 G4 H4 J4 K4W5L4 M4 N4 P4 R4 T4 U4 V4W4W6W7W8W9V19U19W10W11W12W13W14W15W16W17W18W19T19R19P19N19A20 A19 A18 A17 A14 A16 A15 A11 A13 A12 A8 A10 A9 A5 A7 A6A2A4A3J2B2H2K2H21G21F21B21D21C21E21B19B20B18B11F3B12E3B3B15B13G3B14D3B7B8B6B4B10C3B16B17B5B9J19K19M19L19K14E19D16L14D17F19G19D11D6J14D9P10J11D8J13J10N14P12K10H19L9M9D14P14P13D18P11D13D12P9D5K9D19N9L10D10D15J12M14D7N10N11N12L13M13N13K11K12K13M12M11L11L12M10C2D2F2E2G2CXD3814GB IC3202A1D2Y4B1D2Y5C1D2Y7D1D2CLKE1D2C3F1D2C7G1D2HTIMH1VSSJ1AIN1K1AVSAD2L1AIN3M1AVSAD3N1AIN4P1AVSAD45R1AIN5T1VSSU1TEST1V1TDOW1SCAN_SWY1AD4_SELAA1AD5_SELAB1G_I0AB2G_I1AB3G_I3AB4DCV2AB5DCV5AB6DCV8AB7XRSTAB8DQ1AB9DQ4AB10DQ7AB11DQ10AB12DQ13AB13ADDR0AB14ADDR3AB15ADDR6AB16ADDR9AB17XCASAB18XCSAB19DQMAB20SDCLKAB21EXTVAB22OSDRAA22OSDYSY22OSDYMW22OSDHV22OUT1Y1U22OUT1Y4T22OUT1Y7R22OUT1C0P22OUT1C3N22OUT1C6M22OUT1C9L22OUT1CLKK22OUT2R2J22OUT2R5H22OUT2G0G22OUT2G3F22OUT2G6E22OUT2B1D22OUT2B4C22OUT2B6B22OUT2B7A22OUT2CLKA21VSSF2D2C6G2D2VTIMH2VSSJ2AVSAD1K2VRM1L2DVSAD123M2VRB123N2AVSAD4P2VRB4R2AVSAD5T2VRB5U2VSSV2TDIW2TRSTY2CLP_PAA2G_O1AA3G_I2AA4DCV1AA5DCV4AA6DCV7AA7DCVCLKAA8DQ0AA9DQ3AA10DQ6AA11DQ9AA12DQ12AA13DQ15AA14ADDR2AA15ADDR5AA16ADDR8AA17ADDR11AA18XWEAA19BA1AA20CKEAA21SHIZY21OSDBW21OSDCLKV21OUT1Y0U21OUT1Y3T21OUT1Y6R21OUT1Y9P21OUT1C2N21OUT1C5M21OUT1C8L21OUT1VK21OUT2R1J21OUT2R4H21OUT2R7G21OUT2G2F21OUT2G5E21OUT2B0D21OUT2B3C21OUT2B5B21OUT2VB20VSSB19DAAVD1B18DAVREF2B17AVDPLB16VSSB15SDAB14SADSEL0B13IRAM_INITB12IRAM_CKB11D1G2B10D1G5W3TMSY3G_O2Y4DCV0Y5DCV3Y6DCV6Y7DCV9Y8SDENY9DQ2Y10DQ5Y11DQ8Y12DQ11Y13DQ14Y14ADDR1Y15ADDR4Y16ADDR7Y17ADDR10Y18XRASY19BA0Y20MHIZW20OSDGV20OSDVU20OUT1Y2T20OUT1Y5R20OUT1Y8P20OUT1C1N20OUT1C4M20OUT1C7L20OUT1HK20OUT2R0J20OUT2R3H20OUT2R6G20OUT2G1F20OUT2G4E20OUT2G7D20OUT2B2C20OUT2HC19DAAVS1C18DAVREF1C17DAVRO2C16IICCLK_SELC15REFCLK_INC14SCLC13IRAM_MODEC12IRAM_DATC11D1G1C10D1G4C9D1G7C8D1B2C7D1B5C6D1R0C5D1R3C4D1R6D4D2Y1E4D2C0F4D2C4G4D2C8H4VSSJ4AVDAD1K4VRT123L4DVDAD123M4VRM3N4AVDAD4P4VRM4R4AVDAD5T4VRM5D5 DVDK9 VSSL9 VSSM9 VSSN9 VSSP9 VSSP10 VSSP11 VSSP12 VSSP13 VSSP14 VSSN14 VSSM14 VSSL14 VSSK14 VSSJ14 VSSJ13 VSSA20FIFOCLK_INA19AOUT1A18DAAVD2A17AOUT2A16DTOCLK_INA15VSSA14SADSEL1A13IRAM_SELA12D1G0A11D1G3A10D1G6A9D1B1A8D1B4A7D1B7A6D1R2A5D1R5A4D1HTIMA3D1CLKA2D2Y0B2D2Y3C2D2Y6D2D2Y9E2D2C2B9D1B0B8D1B3B7D1B6B6D1R1B5D1R4B4D1R7B3D1VTIMC3D2Y2D3D2Y8E3D2C1F3D2C5G3D2C9H3VSSJ3AIN2K3AVDAD2L3VRM2M3AVDAD3N3VRT4P3DVDAD45R3VRT5T3VSSU3TEST0V3TCKU4VSSV4TEST2W4 DVDW5 DVDW6 DVDW7 DVDW8 DVDW9 DVDW10 DVDW11 AVDW12 AVDW13 AVDW14 AVDW15 AVDW16 AVDW17 AVDW18 AVDW19 AVDV19 AVDU19 AVDT19 AVDR19 AVDP19 AVDD12 DVDD11 DVDD10 DVDD9 DVDD8 DVDD7 DVDD6 DVDD19 DAAVS2D18 DAVRO1D17 AVSPLD16 DVDD15 DVDD14 DVDD13 DVDL19 AVDK19 AVDJ19 AVDH19 AVDG19 AVDF19 AVDE19 AVDN19 AVDM19 AVDJ12 VSSJ11 VSSJ10 VSSK10 VSSL10 VSSM10 VSSN10 VSSN11 VSSN12 VSSN13 VSSM13 VSSL13 VSSK13 VSSK12 VSSK11 VSSL11 VSSM11 VSSM12 VSSL12 VSS54 321NJM2125F(TE2) IC32011+2GND3- 4 OUT5 VCCA1.8VD3.3VMAIN_B/UI2C-TV0D3.3VCCPX_HELIOSA1.8VD3.3VJL3207 XXCLPSWJL3202 XXMAIN_G/YMAIN_R/VMAIN_CV/YMAIN_CCCPX_RSTD3.3VHDMI_VIDEO5445 10123456789 464748495051525335 204042 131744434139383736 191816111214153428293031323321222324252627MT48LC4M16A2P-75:GIC32041 VDD2 DQ03 VDDQ4 DQ15 DQ26 VSSQ7 DQ38 DQ49 VDDQ10 DQ511 DQ612 VSSQ13 DQ714 VDD15 DQML16 WE17 CAS18 RAS19 CS20 BA021 BA122 A1023 A024 A125 A226 A327 VDD 28VSS29A430A531A632A733A834A935A1136NC37CKE38CLK39DQMH40NC41VSS42DQ843VDDQ44DQ945DQ1046VSSQ47DQ1148DQ1249VDDQ50DQ1351DQ1452VSSQ53DQ1554VSS1 2 3 4 5PQ070XZ01ZPH IC3203D3.3V9VMAIN_Y/CV_SAIPHMAIN_CD3.3V I2C-TV0D5VMAIN_G/YMAIN_R/VMAIN_B/UCLPSWMAIN_CV/Y161514131211109 87654321MAX4018EEE-TG068IC32051 ENA2 ENC3 ENB4 VCC5 INA+6 INA-7 OUTA8 NC9NC10OUTB11INB-12INB+13VEE14INC+15INC-16OUTCCCPX_RSTD3.3VRT1A3906-T122-1Q320212316V 0. 1 C32991 26.3V 100 C3201126.3V 100 C3202126.3V 100 C3226126.3V 100 C32301 26.3V 100 C3248126.3V 100 C3277126.3V 100 C33021 26.3V 100 C33041 26.3V 100 C33061 26.3V 100 C3309126.3V 100 C33111 26.3V 100 C3321 121/10W RN-CP220 R32250.5% 121/10W RN-CP220 R32500.5%1 21/10W RN-CP220 R33090.5%122SA1235TP-1EFQ32221234V 47 C32571220126.3V 10BC32141220126.3V 10BC32181220126.3V 10BC3236 1 220126.3V 10BC32371 26.3V 100 C32341 26.3V 100 C32471216081/10W RN-CP 5%R3174 471/10W RN-CP 5%47 R3189 MAIN_VMAIN_HCHIP0 R3337121/10W RN-CP 5%1k R3326 121/10W RN-CP 5%1k R3305 12CHIP0 R3304 121/10W RN-CP220 R33215%121/10W RN-CP 5%560 R3320 12656-HS656-CLK_TO_CCPXA656-VS0 R3256CHIP0 R3301CHIP0 R3258XX R3355RN-CP10k R32531/10W5%12MAIN_CVMAIN_Y/CB/CRATSC_VIDEO1/10W RN-CP330 R33190.5%121/10W RN-CP 0.5%1k R3318 12160816V 0. 1BC32082827262524232221201918171615 1413121110987654321SM5308AS-G-ETIC32091 REF12 VDD3 SDA4 SCL5 VSS6 MUXSEL7 ADS8 IN1A9 IN1B10 ISET11 IN2A12 IN2B13 IN3A14 IN3B 15 GND316 OUT3B17 OUT3A18 VCC319 GND220 OUT2B21 OUT2A22 VCC223 GND124 OUT1B25 OUT1A26 VCC127 REF328 REF2JL3211JL3212CHIP0 R323912DCV9DCV6DCV3DCV0 M-HSMC5MC2MY6MY3MY0XRASADDR10ADDR7ADDR4ADDR1DQ14DQ11DQ8DQ5DQ2SCL-TV0SDA-TV0D3.3VC0_TERMC1_TERMC4_TERMC5_TERMC6_TERMC7_TERMC2_TERMC3_TERMHDMI_CR6HDMI_CR3HDMI_CR0HDMI_CB5HDMI_CB2HDMI_Y7HDMI_Y4HDMI_Y1C6_TERMC2_TERMC7_TERMC3_TERMH-C7H-C6H-C5H-C4H-C3H-C2H-C1H-C0H-Y7H-Y6H-Y5H-Y4H-Y3H-Y2H-Y1H-Y0H-HSH-VSH-CLKM-CLKMC7MC6MC5MC4MC3MC2MC1MC0MY7MY6MY5MY4MY3MY2MY1MY0M-VSMC6MC3MC0MY7MY4MY1XWEADDR11ADDR8ADDR5ADDR2DQ15DQ12DQ9DQ6DQ3DQ0DCVCLKDCV7DCV4DCV1C4_TERMC0_TERMHDMI_VSHDMI_CR7HDMI_CR4HDMI_CR1HDMI_CB6HDMI_CB3HDMI_CB0HDMI_Y5HDMI_Y2HDMI_CLKHDMI_HSMY2MY5MC1MC4MC7M-CLKDQ1DQ4DQ7DQ10DQ13ADDR0ADDR3ADDR6ADDR9XCASXCSDQMDCV2DCV5DCV8DCV0DCV1DCV2DCV3DCV4DCV5DCV6DCV7DCV8DCV9DCVCLKHDMI_Y0HDMI_Y3HDMI_Y6HDMI_CB1HDMI_CB4HDMI_CB7HDMI_CR2HDMI_CR5C1_TERMC5_TERMDQ0DQ1DQ2DQ3DQ4DQ5DQ6DQ7XWEXCASXRASXCSADDR10ADDR0ADDR1ADDR2ADDR3DQMDQ15DQ14DQ13DQ12DQ11DQ10DQ9DQ8ADDR11ADDR9ADDR8ADDR7ADDR6ADDR5ADDR4SDA-TV0SCL-TV0656-0656-7M-HSM-VS656-HS656-CLK_TO_CCPXACV_YCMAIN_YMAIN_CBMAIN_CR656-6656-5656-3656-2656-4656-1MEMORYB(2/ 11)CCP-XABUFFER1.8-REGVIDEO LPFVIDEO LPFVIDEO LPFRESETFIFO/DOTCLKCCP-XA9-883-709-01B-2 60KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010Due to the complexity of this board, performing component level eld repairs is not recommended. If service is required, complete block assembly replacement is the preferred repair method. 1 |2|3 |4 |5 |6 |7 |8 |9 |10 |11 |12 |13 |14 |15 |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |ABCDEFGHIJKLMNOPB BOARD SCHEMATIC DIAGRAM (3 OF 11)6.3V 4. 7CC3407126.3V 4. 7CC34081216086.3V 4. 7CC3436 12 16086.3V 4. 7CC34661216V 0. 1BC34061 216V 0. 1BC34091216V 0. 1BC341012160816V 0. 1BC343212160816V 0. 1BC3433 12160816V 0. 1BC3435 12160816V 0. 1BC3438 12160816V 0. 1BC3439 12160816V 0. 1BC3440 12160816V 0. 1BC344212160816V 0. 1BC3443 12160816V 0. 1BC3445 12160816V 0. 1BC3446 12160816V 0. 1BC3447 12160816V 0. 1BC3467 12160816V 0. 1BC3494 1216V 0. 1 C37521 2160816V 0. 1BC376012160816V 0. 1BC3761 12160816V 0. 1BC375912160816V 0. 1BC375812160816V 0. 1BC376212160816V 0. 1BC37541216V 0. 1 C37501 2160816V 0. 1BC375112160816V 0. 1BC375612160816V 0. 1BC3757 126.3V 47 C3402126.3V 47 C3414126.3V 47 C342112160850V 12pCHC349312160850V 15pCHC34821 2160850V 15pCHC34831 2160825V 0. 01BC3401 12160825V 0. 01BC34041 2160825V 0. 01BC34111 2160825V 0. 01BC34121 2160825V 0. 01BC34131 2160825V 0. 01BC34151 2160825V 0. 01BC34161 2160825V 0. 01BC34171 2160825V 0. 01BC3418 1 2160825V 0. 01BC342412160825V 0. 01BC342512160825V 0. 01BC342612160825V 0. 01BC342812160825V 0. 01BC342912160825V 0. 01BC3430 12160825V 0. 01BC343112160825V 0. 01BC343412160825V 0. 01BC344112160825V 0. 01BC344812160825V 0. 01BC344912160825V 0. 01BC345012160825V 0. 01BC345112160825V 0. 01BC345212160825V 0. 01BC345312 160825V 0. 01BC345412160825V 0. 01BC345512160825V 0. 01BC345612160825V 0. 01BC345812160825V 0. 01BC345912160825V 0. 01BC346012160825V 0. 01BC34681 2160825V 0. 01BC3469 1 2160825V 0. 01BC34701 225V 0. 01BC3471 1 2160825V 0. 01BC34731 2160825V 0. 01BC34741 2160825V 0. 01BC34861 2160825V 0. 01BC34881225V 0. 01BC34891 2160825V 0. 01BC34901 2160825V 0. 01BC349112160825V 0. 01BC376312160825V 0. 01BC375312160825V 0. 1FC37551 2160850V 220pCHC34031 2160850V 220pCHC34051 21/10W RN-CP 0.5%10 R37521 21/10W 33 R34191 21/10W 33 R34201 21/10W 33 R34211 21/10W RN-CP 5%47 R3411 121/10W RN-CP 5%100 R34031 21/10W RN-CP 5%100 R34041 21/10W RN-CP 5%100 R3414 121/10W 100 R3787 1 21/10W 100 R3790 1 21/10W RN-CP 5%150 R3428 121/10W RN-CP 5%150 R3429 121/10W RN-CP 5%150 R3430 121/10W RN-CP 5%220 R34321 21/10W RN-CP 5%10k R34061 21/10W RN-CP 5%10k R34941 21/10W RN-CP 5%10k R3495 1 21/10W RN-CP 5%22k R34051 21/10W RN-CP 5%330k R3431121/10W RN-CP 5%470k R3794121/10W RN-CP 5%470k R375712CHIP0 R340912CHIP0 R3412 12CHIP0 R3413 12CHIP0 R3416 12 CHIP0 R3417 12CHIP0 R34251 2CHIP0 R376312CHIP0 R37931 2CHIP0 R377112CHIP 0 R3792 1 2CHIP 0 R3788 1 2CHIP 0 R3791 1 2CHIP 0 R3785 1 2CHIP 0 R3786 1 2CHIP 0 R3789 1 21/10W RN-CP 0.5%100 R3777121/10W RN-CP470 R34010.5%121/10W RN-CP 0.5%1k R3772121/10W RN-CP47k R37820.5%121/10W RN-CP 0.5%180 R3427121/10W RN-CP 0.5%470 R3750121/10W RN-CP 0.5%470 R37561 21/10W RN-CP 0.5%1k R3400121/10W RN-CP 0.5%1k R37591 21/10W RN-CP 0.5%1k R3778121/10W RN-CP 0.5%1k R3751121/10W RN-CP 0.5%1k R37701 21/10W2k R34181 21/10W RN-CP10k R3769 121/10W RN-CP 0.5%10k R3768 121/10W RN-CP 0.5%10k R3775 121/10W RN-CP 0.5%10k R3761 121/10W RN-CP 0.5%33k R3774121/10W RN-CP 0.5%47k R3754 121/10W RN-CP 0.5%100k R3780121/10W RN-CP 0.5%100k R378312 1/10W RN-CP 0.5%100k R3781121/10W RN-CP 0.5%100k R37841247 RB34052 14 36 58 747 RB34062 14 36 58 747 RB34072 14 36 58 747 RB34082 14 36 58 747 RB34092 14 36 58 747 RB34102 14 36 58 747 RB34112 14 36 58 747 RB34122 14 36 58 733 RB34012 14 36 58 733 RB34022 14 36 58 733 RB34032 14 36 58 733 RB34042 14 36 58 71uHL34031 21uHL34021 21uHL34041 21uHL34061 21uHL34091 210uHL34001 210uHL34011 210uHL34071210uHL3408 121218.543956MHz X34001 42 3UDZSTE-173.3BD37501 2 UDZSTE-173.3BD3751121 2 3 4 5PQ070XZ01ZPHIC34001 2 3 4 5MC2838-T112-1D3015123MC2838-T112-1D30161 232SC3052EF-T1-LEFQ30201232SC3052EF-T1-LEFQ3021 1232SC3052EF-T1-LEFQ37501232SA1235TP-1EFQ3018 1232SA1235TP-1EFQ3019 1231 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230240231232233234235236237238239CXD3808AQIC3401IICTESTEXTPCK1XCLHWPLLHDTSTO1EXTPCK2TSTO2RPLLHDDRCHREFDVD1DVS1XRST2XCETSTEN2TRST2AVD1AVSADC1AYINAVDADC1RTM1RM1RBM1VRTVRBRTM2AVDADC2AVSADC2ACBINRM2ACRINRBM2DVDADCDVSADCAVDAD1AVSAD1XRST1TSTEN1SCANINSCANENBSCANOUTDVDAD1DVSAD1DVDA2DVSAD2AVDAD2AVSAD2TSTINAVD2SUBCLKINAVS2SUBVINSUBHINSUBCIN0SUBCIN1SUBCIN2SUBCIN3DVD2DVS2SUBCIN4SUBCIN5 SUBCIN6SUBCIN7SUBYIN0SUBYIN1AVD3AVS3SUBYIN2SUBYIN3SUBYIN4SUBYIN5SUBYIN6SUBYIN7DVD3DVS3VRFIRFAYOUTAVDDAC1VMOUTAVSDAC1VGVBABOUTAVDDAC2AROUTAVDDAC2AVSPLL4AVDPLL4AVSPLL3AVDPLL3TSTMEMCKAVD4DTX2INAVS4DTX1OUTDTX1INDVD4DYOUT9DYOUT8DYOUT7DYOUT6DYOUT5DYOUT4DVS4DYOUT3DYOUT2DYOUT1DYOUT0DCOUT9DCOUT8AVD5AVS5DCOUT7DCOUT6DCOUT5DCOUT4DCOUT3DCOUT2DVD5DVS5DCOUT1DCOUT0HSOUTVSOUTYSOUTAVS6DSPCLKAVD6SDDAT31SDDAT30SDDAT29SDDAT28SDDAT27DVS6DVD6SDDAT26SDDAT25SDDAT24SDDAT23SDDAT22AVS7AVD7SDDAT21SDDAT20SDDAT19SDDAT18SDDAT17DVS7DVD7SDDAT16SDADR3SDADR4SDADR5SDADR6AVS8AVD8SDADR7SDADR8SDADR9SDADR2SDADR1DVS8DVD8SDADR0SDADR10SDADR11SDADR12SDCSAVS9SDCLKINAVD9SDCLKSDRASSDCKEDVS9DVD9SDCASSDWESDDQM1SDDQM0SDDAT7AVS10AVD10SDDAT6SDDAT5SDDAT4SDDAT3SDDAT2DVS10DVD10SDDAT1SDDAT0SDDAT15SDDAT14SDDAT13AVS11AVD11SDDAT12SDDAT11SDDAT10SDDAT9SDDAT8AVDPLL2VCDRCCPODRCAVSPLL2AVDPLL1VCADCCPOADCAVSPLL1AVD12MAINCLKINAVS12MAINVINMAINHINMAINCIN0MAINCIN1MAINCIN2MAINCIN3DVD11DVS11MAINCIN4MAINCIN5MAINCIN6MAINCIN7MAINYIN0MAINYIN1AVD13AVS13MAINYIN2MAINYIN3MAINYIN4MAINYIN5MAINYIN6MAINYIN7DVD12DVS12IICCKSELSDASCL8765 4321NJM2904V(TE2)IC37511234567854 321NJM2870F25-TE2IC3402 12345 54 321NJM2870F25-TE2IC34031234516V 0. 1BC3478 121/10W 1. 2k R3422121/10W RN-CP 0.5%3. 3k R3423 126.3V 1 C3464 1 216V 0. 1 C34651 2160816V 0. 1BC347612160816V 0. 1BC34791216086.3V 4. 7CC3481 1216V 0. 1 C3477126.3V 4. 7 C34801216V 0. 1 C34751233 RB34002 14 36 58 7CCPX_HELIOSI2C-TV00uHFB34011 20uHFB34001 2CHIP0 R340712HELIOS_DCP1/10W RN-CP 0.5%1k R377312EMIG0uH FL34001 23RN-CPR3779 47k 1/10W0.5%126.3V 100 C3492129VD3.3VIRIS_APLIRIS_HALL_OUTD3.3VHELIOS_Y9VHELIOS_YD3.3VHELIOS_RSTHELIOS_VSIRIS_CTRL160825V 0. 01BC34871 220126.3V 10BC34371220126.3V 10BC34441220126.3V 10BC3484126.3V 100 C3427126.3V 100 C345712160825V 0. 01BC3485121/10W RN-CP 0.5%5. 6k R3755120 R37651 210k R3764121/10W RN-CP 5%33 R3737 12160816V 0. 1BC332012 CHIP0 R3698128765 4321CYISM560BSXTIC33061CLK2VDD3VSS4SSCLK5 SSCC6S17S08XOUT1/10W RN-CP5%22k R3694121/10W RN-CP 5%22k R373512160825V 0. 01BC331912CHIP0 R3736120uHFB36081 2160850V 1000pBC3496 1uHL3405 D3.3V0uHFB34021/10W RN-CP 5%47 R3502CONT VDDOUT GND74.175824MHz X340120126.3V 10BC3497160825V 0. 01BC34988765 4321NJM4556AV(TE2)IC3750123456788765 4321NJM2904V(TE2)IC375212345678123456788P CN37501 FB(-)2 DRIVE(-)3 HOUT(-)4 HIN(-)5 HOUT(+)6 HIN(+)7 FB(+)8 DRIVE(+)1/10W RN-CP 5%1k R34741/10W RN-CP 0.5%3. 9k R3478CHIP0 R3475 MC2838-T112-1D3018160825V 0. 01BC3053IRIS_PEAK2SA1235TP-1EFQ30222SC3052EF-T1-LEFQ30239V1/10W RN-CP 5%2. 2k R3496 12160850V 220pCHC37651/10W RN-CP 5%10k R37481/10W RN-CP 5%10k R3749160816V 0. 047BC349512MC2838-T112-1D30191/10W RN-CP 5%10k R3742160825V 0. 01BC33291/10W RN-CP 5%2. 2k R37411/10W RN-CP 5%10k R37392SC3052EF-T1-LEFQ3013HELIOS_VSD3.3V4895356149505125554523456784710464544 434211121314154140393837363516171819202122343323243225313029262728575859606162636465666768697071727374757677787980818283848586IS42S32200C1-6TL-TRIC34041 VCC2 DQ03 VCCQ4 DQ15 DQ26 VSSQ7 DQ38 DQ49 VCCQ10 DQ511DQ612 VSS