Specifications Technical MGE™Galaxy™PW …€¢ ANSI/IEEEC62.41 ... shortcircuit withstand(kA)...

TechnicalSpecificationsMGE™ Galaxy™ PW

150–225 kVA 480 V

test

American Power Conversion Legal Disclaimer

The information presented in this manual is not warranted by the American Power ConversionCorporation to be authoriative, error free, or complete. This publication is not meant to bea substitute for detailed operational and site specific development plan. Therefore, AmericanPower Conversion Corporation assumes no liability for damages, violations of codes, improperinstallation, system failures, or any other problems that could arise based on the use of thisPublication.

The information contained in this Publication is provided as is and has been prepared solelyfor the purpose of evaluating data center design and construction. This Publication has beencompiled in good faith by American Power Conversion Corporation. However, no presentationis made or warranty, either express or implied, as to the completeness or accuracy of theinformation this Publication contains.

NO EVENT SHALL AMERICAN POWER CONVERSION CORPORATION BE LIABLEFOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL, ORINCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FORLOSS OF BUSINESS, CONTRACT, REVENUE, DATA, INFORMATION, OR BUSINESSINTERRUPTION) RESULTING FROM, ARISING OUT, OR IN CONNECTION WITH THEUSE OF, OR INABILITY TO USE THIS PUBLICATION OR THE CONTENT, EVEN IFAMERICAN POWER CONVERSION CORPORATION HAS BEEN EXPRESSLY ADVISEDOF THE POSSIBILITY OF SUCH DAMAGES. AMERICAN POWER CONVERSIONCORPORATION RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITHRESPECT TO OR IN THE CONTENT OF THE PUBLICATION OR THE FORMATTHEREOF AT ANY TIME WITHOUT NOTICE.

Copyright, intellectual, and all other proprietary rights in the content (including but not limitedto software, audio, video, text, and photographs) rests with American Power ConversionCorporation or its licensors. All rights in the content not expressly granted herein are reserved.No rights of any kind are licensed or assigned or shall otherwise pass to persons accessingthis information.

This Publication shall not be for resale in whole or in part.

Table of Contents

Technical Data .................................................................................................................. 1

Model List....................................................................................................................... 1

Input Power Factor ...................................................................................................... 1

Efficiency........................................................................................................................ 2Efficiency Curves....................................................................................................... 2

Derating due to Load Power Factor ........................................................................ 2

Batteries ......................................................................................................................... 3Efficiency DC to AC ................................................................................................... 3Battery Runtimes ....................................................................................................... 3Battery Discharge Current ......................................................................................... 7End of Discharge Voltage .......................................................................................... 7Battery Material Safety Data Sheet ............................................................................ 8

Compliance .................................................................................................................... 8

Facility Planning ............................................................................................................. 9

AC Input Specifications.............................................................................................. 9

AC Output Specifications ..........................................................................................10

AC Bypass Input Specifications ..............................................................................11

Battery Specifications ................................................................................................11

Overcurrent Protection...............................................................................................12Overcurrent Protective Devices in Single Systems ...................................................12

Physical ..........................................................................................................................13Weights and dimensions ...........................................................................................13Shipping Weights and dimensions ............................................................................13Clearance...................................................................................................................13

Environmental...............................................................................................................13Heat Dissipation ........................................................................................................13

Drawings .............................................................................................................................14

MGE Galaxy PW Bottom Cable Entry System with 65 kAIC available ...........15

MGE Galaxy PW Bottom Cable Entry System with 65 kAIC notavailable..........................................................................................................................16

MGE Galaxy PW Bottom Cable Entry System with IsolationTransformer ...................................................................................................................17

990–5243 MGE™ Galaxy™ PW Technical Specifications i

MGE Galaxy PW Bottom Cable Entry System with Maintenance BypassPanel and Isolation Transformer..............................................................................18

MGE Galaxy PW Top or Bottom Cable Entry System with MaintenanceBypass Panel ................................................................................................................19

MGE Galaxy PW Top Cable Entry System.............................................................20

MGE Galaxy PW Top Cable Entry System with Distribution and InternalMBP..................................................................................................................................21

MGE Galaxy PW Top Cable Entry System with Isolation Transformer ...........22

MGE Galaxy PW Top Cable Entry System with Isolation Transformerand Maintenance Bypass Panel ...............................................................................23

Options .................................................................................................................................24

Hardware Options ........................................................................................................24

APC by Schneider Electric Limited Factory Warranty ..............................25

Three Phase Power Products or Cooling Solutions One-Year FactoryWarranty .........................................................................................................................25

Terms of Warranty........................................................................................................25

Non-transferable Warranty ........................................................................................25

Assignment of Warranties .........................................................................................25

Drawings, Descriptions ..............................................................................................25

Exclusions .....................................................................................................................25

Warranty Claims ...........................................................................................................26

ii MGE™ Galaxy™ PW Technical Specifications 990–5243

Technical Data

Model List• MGE GALAXY PW 150 kVA• MGE GALAXY PW 180 kVA• MGE GALAXY PW 200 kVA• MGE GALAXY PW 225 kVA

Input Power Factor

990–5243 MGE™ Galaxy™ PW Technical Specifications 1

Efficiency20 % load 50 % load 70 % load 100 % load

88.04 93.18 93.63 93.18

Efficiency Curves

Derating due to Load Power Factor150 kVA/150kW

180 kVA/180kW

200 kVA/200kW

225 kVA/202.5kW

0.6 150 180 200 225

0.7 150 180 200 225

0.8 150 180 200 225

Lagging

0.9 150 180 200 225

Unity 1 150 180 200 202

0.9 150 180 181 181

0.8 150 174 174 174

0.7 150 169 169 169

Leading

0.6 150 166 166 166

2 MGE™ Galaxy™ PW Technical Specifications 990–5243

BatteriesEfficiency DC to AC

Battery RuntimesBattery Cabinet #: 72 - 131302 - 00 / 01 with Battery, UPS12-270FR or UPS12-300MR

Output Power Factor 0.8

1 String 2 Strings 3 Strings 4 StringsKVA / kW

Minutes Minutes Minutes Minutes

150 / 120 - 16 30 41

180 / 144 - 12 22 35

200 / 160 - 10 20 30

225 / 180 - 8 16 26

Battery Cabinet #: 72 - 131302 - 00 / 01 with Battery, UPS12-270FR or UPS12-300MR




150 / 150 - 11 21 32

180 / 180 - 8 16 26

200 / 200 - 7 14 21

225 / 202.5* - 6 13 21

* Power Factor 0.9 for 225 kVA

Battery Cabinet #: 72 - 131302 - 10 / 11 with Battery GNB S12V285 or GNB - S12V285F




150 / 120 - 16 30 41

180 / 144 - 12 22 35

200 / 160 - 10 20 30

225 / 180 - 8 16 26


Battery Cabinet #: 72 - 131302 - 10 / 11 with Battery GNB S12V285 or GNB - S12V285F




150 / 150 - 11 21 32

180 / 180 - 8 16 26

200 / 200 - 7 14 21

225 / 202.5* - 6 13 21


Battery Cabinet #: 72 - 131302 - 30 / 31 with Battery Enersys - HX300-12FR




150 / 120 - 16 30 41

180 / 144 - 12 22 35

200 / 160 - 10 20 30

225 / 180 - 8 16 26

Battery Cabinet #: 72 - 131302 - 30 / 31 with Battery Enersys - HX300-12FR




150 / 150 - 11 21 32

180 / 180 - 8 16 26

200 / 200 - 7 14 21

225 / 202.5* - 6 13 21






150 / 120 9 25 42 60

180 / 144 6 20 33 48

200 / 160 5 17 30 42

225 / 180 - 14 24 36






150 / 150 6 19 32 46

180 / 180 - 14 24 36

200 / 200 - 12 22 33

225 / 202.5* - 12 22 32


Battery Cabinet #: 72 - 131304 - 10 / 11 with Battery GNB - S12V370 or S12V370F




150 / 120 9 25 42 60

180 / 144 6 20 33 48

200 / 160 5 17 30 42

225 / 180 - 14 24 36





150 / 150 6 19 32 46

180 / 180 - 14 24 36

200 / 200 - 12 22 33

225 / 202.5* - 12 22 32


Battery Cabinet #: 72 - 131304 - 30 / 31 with Battery Enersys - PHX12-370Battery Cabinet #: 72 - 131304 - 32 / 33 with Battery Enersys - HX400-12FR




150 / 120 9 25 42 60

180 / 144 6 20 33 48

200 / 160 5 17 30 42

225 / 180 - 14 24 36






150 / 150 6 19 32 46

180 / 180 - 14 24 36

200 / 200 - 12 22 33

225 / 202.5* - 12 22 32






150 / 120 12 36 59 85

180 / 144 8 28 46 68

200 / 160 6 24 41 60

225 / 180 - 19 37 51





150 / 150 7 26 45 63

180 / 180 - 19 37 51

200 / 200 - 17 31 45

225 / 202.5* - 16 31 44






150 / 120 12 36 59 85

180 / 144 8 28 46 68

200 / 160 6 24 41 60

225 / 180 - 19 37 51






150 / 150 7 26 45 63

180 / 180 - 19 37 51

200 / 200 - 17 31 45

225 / 202.5* - 16 31 44






150 / 120 12 36 59 85

180 / 144 8 28 46 68

200 / 160 6 24 41 60

225 / 180 - 19 37 51





150 / 150 7 26 45 63

180 / 180 - 19 37 51

200 / 200 - 17 31 45

225 / 202.5* - 16 31 44


Battery Discharge Current

150 kVA 180 kVA 200 kVA 225 kVA

Ibat @ Vbatnominal, 100% load

299 359 399 449

Ibat @ Vbat min,100% load

403 484 540 547

End of Discharge Voltage

Minimum battery end of discharge voltage 390 V

Minimum battery value per cell 1.65 V


Battery Material Safety Data Sheet

Note: For Material Safety Data Sheet (MSDS), go to“http://nam-en.apc.com/app/answers/detail/a_id/564/kw/msds“.

Compliance

• UL 1778

• UL Canada (cUL)

• ANSI/IEEE C62.41

• ISO 9001

• National Fire Protection Association (NFPA); NEC

• National Electrical Manufacturers Association (NEMA)

• Occupational Safety and Health Administration (OSHA)


Facility Planning

AC Input Specifications150 kVA/150 kW 180 kVA/180 kW

Voltage (V)Input/Output

208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Phase rotation A, B, C Clockwise

Connectiontype

3–wire (3Ph + G)

Inputfrequency (Hz)

60 ±10%

THDI Less than 7.5% at full load

Nominal inputcurrent (A)

485 210 210 168 168 600 260 260 208 208

Maximuminput current(A)

533 231 231 185 185 660 286 286 229 229

Input currentlimitation (A)

360 (1.5 In 225 kVA) 360 (1.5 In 225 kVA)

Input powerfactorcorrection

Up to 0.9 at full load

Maximumshort circuitwithstand (kA)

33 27

200 kVA/200 kW 225 kVA/202.5 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Phase rotation A, B, C Clockwise

Connectiontype

3–wire (3Ph + G)

Inputfrequency (Hz)

60 ±10%

THDI Less than 7.5% at full load

Nominal inputcurrent (A)

692 300 300 240 240 692 300 300 240 240

Maximuminput current(A)

738 320 320 256 256 738 320 320 256 256

Input currentlimitation (A)

360 (1.5 In 225 kVA) 360 (1.5 In 225 kVA)

Input powerfactorcorrection

Up to 0.9 at full load

Maximumshort circuitwithstand (kA)

25 22


AC Output Specifications150 kVA/150 kW 180 kVA/180 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Connectiontype

3 wire (3PH + G) or 4 wire (3PH + N + G)

Overloadcapacity

10 minutes @ 125%60 seconds @ 150%

Voltagetolerance

± 10%

Nominaloutput current(A)

418 418 181 418 145 501 501 217 501 174

Outputfrequency(sync tobypass) (Hz)

60 ±2.0

Slew rate 2.0 Hz/second maximum (selectable in 0.5 Hz/second increments)

THDU < 1% linear< 4% non-linear

Load powerfactor

0.9

Dynamic loadresponse

+/-2% load step with battery+2% / –6% load step without battery

Output voltageregulation

+/-1% static and +/- 5% at 100% load step

Crest Factor 3.5

200 kVA/200 kW 225 kVA/202.5 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Connectiontype

3 wire (3PH + G) or 4 wire (3PH + N + G)

Overloadcapacity

10 minutes @ 125%60 seconds @ 150%

Voltagetolerance

± 10%

Nominaloutput current(A)

558 558 241 558 217 625 625 271 625 217

Outputfrequency(sync tobypass) (Hz)

60 ±2.0

Slew rate 2.0 Hz/second maximum (selectable in 0.5 Hz/second increments)

THDU < 1% linear< 4% non-linear

Load powerfactor

0.9

Dynamic loadresponse

+/-2% load step with battery+2% / –6% load step without battery


200 kVA/200 kW 225 kVA/202.5 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Output voltageregulation

+/-1% static and +/- 5% at 100% load step

Crest Factor 3.5

AC Bypass Input Specifications150 kVA/150 kW 180 kVA/180 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Inputfrequency (Hz)

60Hz +/- 10%

Nominal inputcurrent

418 418 181 418 145 501 501 217 501 174

200 kVA/200 kW 225 kVA/202.5 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Inputfrequency (Hz)

60Hz +/- 10%

Nominal inputcurrent

558 558 241 558 217 625 625 271 625 217

Battery SpecificationsType Seal lead acid or vented lead-acid

150 kVA/150 kW 180 kVA/180 kW 200 kVA/200 kW 225 kVA/202.5 kW

Nominal voltage(VDC)

480

Float voltage (VDC) 545 (512–561)

End of dischargevoltage (VDC)

390

Battery Current atfull load (A)1

280 336 375 380

Maximum Current(at end of discharge)(A)1

403 484 540 547

Typical rechargetime

12 hours

End voltage > 1.65 V/cell1 at battery voltage 561


Overcurrent Protection

Overcurrent Protective Devices in Single Systems

150 kVA/150 kW 180 kVA/180 kW


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Utility input 700 300 300 250 250 825 400 400 300 300

Static bypassinput

600 600 250 600 200 800 800 300 800 225

Output 600 600 250 600 200 800 800 300 800 225

Maintenancebypass

600 600 250 600 200 800 800 300 800 225

Battery input Refer to “Drawings“.

200 kVA/200 kW 225 kVA/202.5


208/208 480/208 480/480 600/208 600/600 208/208 480/208 480/480 600/208 600/600

Utility input 1000 400 400 300 300 1000 400 400 350 350

Static bypassinput

800 800 300 800 250 800 800 350 800 300

Output 800 800 300 800 250 800 800 350 800 300

Maintenancebypass

800 800 300 800 250 800 800 350 800 300

Battery input Refer to “Drawings“.


Physical

Weights and dimensions

UPS Weight kg (lbs) Height mm (in) Width mm (in) Depth mm (in)

150 kVA 1200 (2640) 1900 (74.80) 1215 (47.83) 855 (33.66)

180 kVA 1200 (2640) 1900 (74.80) 1215 (47.83) 855 (33.66)

200 kVA 1200 (2640) 1900 (74.80) 1215 (47.83) 855 (33.66)

225 kVA 1200 (2640) 1900 (74.80) 1215 (47.83) 855 (33.66)

Shipping Weights and dimensions

UPS Weight kg (lbs) Height mm (in) Width mm (in) Depth mm (in)

150 kVA 1432 (3150) 2108 (83) 1320 (51.97) 940 (37)

180 kVA 1432 (3150) 2108 (83) 1320 (51.97) 940 (37)

200 kVA 1432 (3150) 2108 (83) 1320 (51.97) 940 (37)

225 kVA 1432 (3150) 2108 (83) 1320 (51.97) 940 (37)

Clearance

Note: Clearance dimensions are published for airflow and service access only. Consult withthe local safety codes and standards for additional requirements in your local area.

EnvironmentalOperating temperature 0–35°C (32–95°F)

Storage temperature -20–45°C (-4–113°F)

Operating relative humidity 0–95%

Storage relative humidity 0–95%

Operating elevation 0–1000 m (3281 ft) = 100% load1000–1500 m (3281–4921 ft) = 85% load1500–2000 m (4921–6562 ft) = 79% load2000–2300 m (6562–7546 ft) = 75% load2300–3000 m (7546–9843 ft) = 69% load3000–4000 m (9843–13123 ft) = 61% load

Storage elevation ≤ 10000 meter (32808 ft)

Audible noise – 1 meter from surface of unit 150 kVA: 64 dBA180 kVA: 65 dBA200 kVA: 67 dBA225 kVA: 68 dBA

Protection Class IP 205

Colour RAL 9002

Heat Dissipation

150 kVA/150 kW 180 kVA/180 kW 200 kVA/200 kW 225 kVA/202.5 kW

Heat dissipationBTU/hr

38534 46240 47453 48046


Drawings

Note: A comprehensive set of drawings is available on the engineering website atwww.engineer.apc.com.

Note: These drawings are for reference ONLY — subject to change without notice.


MGE Galaxy PW Bottom Cable Entry System with 65kAIC available


MGE Galaxy PW Bottom Cable Entry System with 65kAIC not available


MGE Galaxy PW Bottom Cable Entry System withIsolation Transformer


MGE Galaxy PW Bottom Cable Entry System withMaintenance Bypass Panel and Isolation Transformer


MGE Galaxy PW Top or Bottom Cable Entry Systemwith Maintenance Bypass Panel


MGE Galaxy PW Top Cable Entry System


MGE Galaxy PW Top Cable Entry System withDistribution and Internal MBP


MGE Galaxy PW Top Cable Entry System with IsolationTransformer


MGE Galaxy PW Top Cable Entry System with IsolationTransformer and Maintenance Bypass Panel


Options

Hardware Options

• MGE Galaxy PW Empty Auxiliary Cubicle

• MGE Galaxy PW External Batteries

• MGE Galaxy PW External Option

• MGE Galaxy PW External Bypass Cubicle

• MGE Galaxy PW External Bypass Option

• MGE Galaxy PW Parallel Bypass Cabinet

• MGE Galaxy PW Transformer


APC by Schneider Electric LimitedFactory Warranty

Three Phase Power Products or Cooling SolutionsOne-Year Factory WarrantyThe limited warranty provided by APC by Schneider Electric (APC®) in this Statement of LimitedFactory Warranty applies only to products you purchase for your commercial or industrial use in theordinary course of your business.

Terms of WarrantyAmerican Power Conversion warrants that the product shall be free from defects in materials andworkmanship for a period of one year from the date of product start-up when start-up is performedby APC authorized service personnel and occurs within six months of The APC shipment date. Thiswarranty covers repairing or replacing any defective parts including on-site labor and travel. In theevent that the product fails to meet the foregoing warranty criteria, the warranty covers repairing orreplacing defective parts at the sole discretion of APC for a period of one year from the shipment date.For APC cooling solutions, this warranty does not cover circuit breaker resetting, loss of refrigerant,consumables, or preventive maintenance items. Repair or replacement of a defective product or partthereof does not extend the original warranty period. Any parts furnished under this warranty may benew or factory-remanufactured.

Non-transferable WarrantyThis warranty is extended to the first person, firm, association or corporation (herein referred to by“You” or “Your”) for whom the APC product specified herein has been purchased. This warranty is nottransferable or assignable without the prior written permission of APC.

Assignment of WarrantiesAPC will assign you any warranties which are made by manufacturers and suppliers of components ofthe APC product and which are assignable. Any such warranties are assigned “AS IS” and APC makesno representation as to the effectiveness or extent of such warranties, assumes no responsibility for anymatters which may be warranted by such manufacturers or suppliers and extends no coverage under thisWarranty to such components.

Drawings, DescriptionsAPC warrants for the warranty period and on the terms of the warranty set forth herein that theAPC product will substantially conform to the descriptions contained in the APC Official PublishedSpecifications or any of the drawings certified and agreed to by contract with APC if applicable thereto(“Specifications”). It is understood that the Specifications are not warranties of performance and notwarranties of fitness for a particular purpose.

ExclusionsAPC shall not be liable under the warranty if its testing and examination disclose that the alleged defect inthe product does not exist or was caused by end user or any third person misuse, negligence, improper


installation or testing. Further APC shall not be liable under the warranty for unauthorized attempts torepair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site operationconditions, corrosive atmosphere, repair, installation, start-up by non-APC designated personnel, a changein location or operating use, exposure to the elements, Acts of God, fire, theft, or installation contraryto APC recommendations or specifications or in any event if the APC serial number has been altered,defaced, or removed, or any other cause beyond the range of the intended use.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OROTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENTOR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED WARRANTIES OFMERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. APCEXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY ANDNO OBLIGATION OR LIABILITY WILL ARISE OUT OF, APC RENDERING OF TECHNICAL OROTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOINGWARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIESAND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITYAND PURCHASER’S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES.APC WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRDPARTIES.

IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEESBE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVEDAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS,WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT,NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCEOF THE POSSIBILITY OF SUCH DAMAGES, SPECIFICALLY, APC IS NOT LIABLE FOR ANYCOSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OFEQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BYTHIRD PARTIES, OR OTHERWISE.

NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THETERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY INWRITING SIGNED BY AN APC OFFICER AND LEGAL DEPARTMENT.

Warranty ClaimsCustomers with warranty claims issues may access the APC worldwide customer support networkthrough the APC web site: “http://www.apc.com/support/contact/“. Select your country from the countryselection pull-down menu. Open the Support tab at the top of the web page to obtain contact informationfor customer support in your region.


http://www.apc.com/support/contact/


Worldwide Customer Support

Customer support is available at no charge via e-mail or telephone. Contact information is available atwww.apc.com/support/contact

© APC by Schneider Electric. APC and the APC logo are owned by Schneider Electric IndustriesS.A.S., American Power Conversion Corporation, or their affiliated companies. All other trademarksare property of their respective owners.

990–5243 03/2012

Date post:	19-May-2018
Category:	Documents
Upload:	donhi
View:	227 times
Download:	3 times

Specifications Technical MGE™Galaxy™PW …€¢ ANSI/IEEEC62.41 ... shortcircuit withstand(kA)...

Documents