TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Description Symbol Unit EquationNormal Module mnTransverse Module mt = mnNormal Pressure Angle an degrees = 20°Transverse Pressure Angle at degrees = anNumber of Teeth zProfile Shift Coefficient x = zero for Ondrives standard gearsAddendum ha mm = 1.00 · mn (for Ondrives standard gears)Dedendum hf mm = 1.25 · mn (for Ondrives standard gears)Tooth Depth h mm = 2.25 · mn (for Ondrives standard gears)Gear Ratio u = z2 / z1Centre Distance a mm = (d1 +d2) / 2Pitch Circle Diameter d mm = z · mn Tip Diameter da mm = d + (2mn · x) + (2 · mn)Root Diameter dr mm = da – (2 · h)Normal Pitch pn mm = p · mnNormal Tooth Thickness in Pitch Circle sn mm = (pn / 2) + 2mn · x · tan anWhen working with a pair of gears the subscript 1 and 2 denotes input (drive) and output (driven) gear.Tip diameter is the theoretical diameter of the gear without tooth thickness tolerance applied.For sn when x = zero, this is the theoretical tooth thickness. Actual tooth thickness will be less. The subscript e is for upper allowance values and i for lower allowance values.
da1 dr1
sn
pn
a
d1
Spur Gears
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
TorqueStated value for metal spur gears is maximum torque (T2) based on two identical gears with the same number of teeth running at standard centres. Value is minimum from surface stress or bending stress.Other factors including duty cycle and temperature will affect maximum allowable torque and service life. Wear is dependant on lubrication. We recommend that each user compute their own values based on actual operating conditions and test in application.
Gear QualityStandard metal gears are supplied to quality Grade 7 DIN 3961 based on Pitch total deviation Fp, Pitch deviation fp, Radial runout Fr and Pitch error fu. Skive hobbed gears are supplied to quality Grade 6 DIN 3961. GG25 Cast Iron, PEEK GF30® and Delrin (POM) are supplied to quality Grade 8 DIN 3961.Ondrives can manufacture gears to higher grades on request. Ondrives can offer testing certification for a gear’s individual parameters using the latest CMM machine with gear measuring software.Double and single flank testing is available on request. Please contact our technical department for details.Comparisons of Grade StandardsExample 3 mod, 50 teeth, 30mm face width spur gear.
Working characteristicsof driving machineUniformLight ShocksModerate ShocksHeavy Shocks
Uniform1.001.101.251.50
Light Shocks1.251.351.501.75
Moderate Shocks1.501.601.752.00
Heavy Shocks1.751.852.002.25+
Working characteristics of driven machine
MaterialsInput SpeedBending Stress Factor SbSurface Stress Factor Sc
817M40
32,000 3,000
805M20
50,00011,000
303 Stainless
20,000 1,800
316 Stainless
15,800 1,400
GG25 Cast Iron
7,6001,350
100 rpm Uniform, 12 hours running per day
Stated value for plastic spur gears is maximum torque (T2) based on two identical gears with the same number of teeth running at standard centres. Value is minimum from surface stress, bending stress or bulk/surface temperature using method from BS 6168:1987.The torque capacity of plastic gears is highly dependant on operating condition. All values are reference only. We recommend that each user test in application under specific operation conditions of application.
* Reference Only ** Approximate value based on initial light greasing.Maximum torque for titanium gears is approximately 30% of 817M40 steel gears.Due to lack of stress factors we are unable to offer specific values. Testing in application is required.Torque for anti-backlash spur gears is limited by the spring rating. Please contact our Technical department for details.When selecting gears application factors should be applied to required torque. T2 > Trequired x Ka Application factor Ka
MaterialsInput Speed / No. of Load CyclesLimiting Bending StressLimiting Surface StressInitial TemperatureMax. Bulk or Surface TemperatureCoefficient of Friction
Delrin POM (White)100 rpm / 108
22.0 N/mm2
22.0 N/mm2
20°C60°C
0.18 (Dry)
PEEK GF30® (Light Brown)100 rpm / 108
30 N/mm2*
80 N/mm2*
20°C80°C
0.25**
Spur Gears
Pitch total deviation Fp µm 32 44 50 51Pitch deviation fp µm 8 12 13 13Radial runout Fr µm 22 31 40 41Pitch error fu µm 10 15 - -Double flank composite transmission error Fi" µm 26 36 61 61Double flank tooth-to-tooth transmission error fi" µm 11 15 21 20
StandardGrade
DIN 39616
DIN 39617
ISO 13287
AGMA10
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
da1 dr1
st
pt
ab
d1
Parallel Helical Gears
Description Symbol Unit EquationNormal Module mnTransverse Module mt = mn / cos bAxial Module mx = mn / sin bNormal Pressure Angle an degrees = 20°Transverse Pressure Angle at degrees = tan-1 (tan an / cos b)Helix Angle b degrees = 15°Lead Angle l degrees = 90 - bNumber of Teeth zProfile Shift Coefficient x = zero for Ondrives standard gearsAddendum ha mm = 1.00 · mn (for Ondrives standard gears)Dedendum hf mm = 1.25 · mn (for Ondrives standard gears)Tooth Depth h mm = 2.25 · mn (for Ondrives standard gears)Gear Ratio u = z2 / z1Centre Distance a mm = (d1 +d2) / 2Pitch Circle Diameter d mm = z · mt = (z · mn) / cos bTip Diameter da mm = d + (2mn · x) + (2 · mn)Root Diameter dr mm = da – (2 · h)Normal Pitch pn mm = p · mnTransverse Pitch pt mm = p · mt = (p · mn) / cos bAxial Pitch px mm = p · mx = (p · mn) / sin bNormal Tooth Thickness in Pitch Circle sn mm = (pn / 2) + 2mn · x · tan anTransverse Tooth Thickness in Pitch Circle st mm = (pt / 2) + 2mn · x · tan at = Sn / cos bWhen working with a pair of gears the subscript 1 and 2 denotes input (drive) and output (driven) gear.Tip diameter is the theoretical diameter of the gear without tooth thickness tolerance applied.For sn & st when x = zero, this is the theoretical tooth thickness. Actual tooth thickness will be less. The subscript e is for upper allowance values and i for lower allowance values.For two helical gears to run together one must be left hand and the other right hand helix.
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R SParallel Helical Gears
TorqueStated value for metal spur gears is maximum torque (T2) based on two identical gears with the same number of teeth running at standard centres. Value is minimum from surface stress or bending stress.Other factors including duty cycle and temperature will affect maximum allowable torque and service life. Wear is dependant on lubrication. We recommend that each user compute their own values based on actual operating conditions and test in application.
Gear QualityStandard gears are supplied to quality grade 7e25 DIN 3961 based on the following parameters
Radial Runout Fr =
Pitch Deviation fp =
Total Pitch Deviation Fp =
Pitch Error fu =
Ondrives manufacture gears to higher quality grades on request. Ondrives can offer testing certification of a gears individual parameters using the latest CMM machine with gear measuring software. Double and single flank testing is available on request. Please contact our technical department for details.
Comparisons of Grade StandardsExample 3 mod, 50 teeth, 30mm face width 15° helix parallel helical gear.
Working characteristicsof driving machineUniformLight ShocksModerate ShocksHeavy Shocks
Uniform1.001.101.251.50
Light Shocks1.251.351.501.75
Moderate Shocks1.501.601.752.00
Heavy Shocks1.751.852.002.25+
Working characteristics of driven machine
MaterialsInput SpeedBending Stress Factor SbSurface Stress Factor Sc
817M40
32,000 3,000
805M20
50,00011,000
303 Stainless
20,000 1,800
316 Stainless
15,800 1,400
100 rpm Uniform, 12 hours running per day
When selecting gears application factors should be applied to required torque. T2 > Trequired x Ka Application factor Ka
Pitch total deviation Fp µm 47 50 55Pitch deviation fp µm 12 13 12Radial runout Fr µm 31 40 44Pitch error fu µm 15 - -Double flank composite transmission error Fi" µm 36 61 65Double flank tooth-to-tooth transmission error fi" µm 15 21 20
StandardGrade
DIN 39617
ISO7
AGMA10
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
b
l
da1
px
st
pt
a
d1
Crossed Axis Helical Gears
Description Symbol Unit EquationNormal Module mnTransverse Module mt = mn / cos bAxial Module mx = mn / sin bNormal Pressure Angle an degrees = 20°Transverse Pressure Angle at degrees = tan-1 (tan an / cos b)Helix Angle b degrees = 45°Lead Angle l degrees = 90 - bNumber of Teeth zProfile Shift Coefficient x = zero for Ondrives standard gearsAddendum ha mm = 1.00 · mn (for Ondrives standard gears)Dedendum hf mm = 1.25 · mn (for Ondrives standard gears)Tooth Depth h mm = 2.25 · mn (for Ondrives standard gears)Gear Ratio u = z2 / z1Centre Distance a mm = (d1 +d2) / 2Pitch Circle Diameter d mm = z · mt = (z · mn) / cos bTip Diameter da mm = d + (2mn · x) + (2 · mn)Root Diameter dr mm = da – (2 · h)Normal Pitch pn mm = p · mnTransverse Pitch pt mm = p · mt = (p · mn) / cos bAxial Pitch px mm = p · mx = (p · mn) / sin bNormal Tooth Thickness in Pitch Circle sn mm = (pn / 2) + 2mn · x · tan anTransverse Tooth Thickness in Pitch Circle st mm = (pt / 2) + 2mn · x · tan atWhen working with a pair of gears the subscript 1 and 2 denotes input (drive) and output (driven) gear.Tip diameter is the theoretical diameter of the gear without tooth thickness tolerance applied.For sn & st when x = zero, this is the theoretical tooth thickness. Actual tooth thickness will be less. The subscript e is for upper allowance values and i for lower allowance values.For two crossed axis helical gears to run together both must be right hand or left hand helix.
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Direction of Rotation
Right Hand Helix Left Hand Helix
Crossed Axis Helical Gears
TorqueStated value is maximum torque (T2) based on two identical gears with the same number of teeth running at standard centres. Crossed axis helical gears transmit load by point contact. The limiting condition is typically surface stress. Other factors including duty cycle and temperature will affect maximum allowable torque and service life. Wear is dependant on lubrication.We recommend that each user compute their own values based on actual operating conditions and test in application.
Working characteristicsof driving machineUniformLight ShocksModerate ShocksHeavy Shocks
Uniform1.001.101.251.50
Light Shocks1.251.351.501.75
Moderate Shocks1.501.601.752.00
Heavy Shocks1.751.852.002.25+
Working characteristics of driven machine
When selecting gears application factors should be applied to required torque. T2 > Trequired x Ka Application factor Ka
817M40
32,000 3,000
805M20 (SAE 8620) Case Hardened
50,00011,000
100 rpm uniform speed
Mineral OilBetween 60mm2/s and 130mm2/s at 60°C
MaterialsInput SpeedBending Stress Factor SbSurface Stress Factor Sc
LubricationLubrication Viscosity
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
d2 dr2 da2 de2
a
X N
l
N Xd1
Worms & Wheels
Description Symbol Unit EquationAxial Module mxNormal Module mn = mx · cos l Normal Pressure Angle an degrees = 20°Transverse Pressure Angle at degrees = tan-1 (tan an / cos l)Lead Angle l degrees = tan-1 ((mx · z1) / d1)Helix Angle b degrees = 90 - lNumber of Starts on Worm z1Number of Teeth on Wheel z2Profile Shift Coefficient x = zero for Ondrives standard wormsAddendum ha mm = 1.00 · mx (for Ondrives standard worms)Dedendum hf mm = 1.25 · mx (for Ondrives standard worms)Tooth Depth h mm = 2.25 · mx (for Ondrives standard worms)Gear Ratio u = z2 / z1Centre Distance a mm = (d1 +d2) / 2Reference Diameter of Worm d1 mm = (mx · z1) / tan lReference Diameter of Wheel d2 mm = mx · z2Tip Diameter of Worm da1 mm = d1 + (2 · mx)Root Diameter of Worm dr1 mm = da1 – (2 · h)Tip Diameter of Wheel da2 mm = d2 + (2 · mx)Root Diameter of Wheel dr2 mm = da2 – (2 · h)Outside Diameter of Wheel de2 mm = da2 + mxNormal Pitch pn mm = p · mnAxial Pitch px mm = p · mxNormal Tooth Thickness in Pitch Circle sn mm = sx · cos lTransverse Tooth Thickness in Pitch Circle sx mm = (px / 2)QualitySteel and Stainless Steel worm = Quality 6, DIN 3974. Bronze wormwheel = Quality 7, DIN 3974. PEEK and Delrin worms = Quality 7, DIN 3974. PEEK and Delrin wormwheel = Quality 8, DIN 3974.When working with a gear set, the subscript 1 denotes a worm and 2 a wormwheel. Tip diameter is the theoretical diameter of the gear without tooth thickness tolerance applied.For sn & sx when x = zero, this is the theoretical tooth thickness. Actual tooth thickness will be less. The subscript e is for upper allowance values and i for lower allowance values.
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
TE
CH
NIC
AL
Axial SectionNormal Sectionpn
dr1 d1 da1
sn px sx
hahf
Worms & Wheels
TorqueStated value is maximum torque based on lowest figure from surface durability, tooth root strength or wear.Values for bronze and cast iron wheel are for matching with steel 817M40 worm.Value is output torque (T2) at wheel.Tooth root failure of teeth on wheel before teeth of worm is assumed.Other factors including worm shaft deflection, duty cycle and temperature will affect maximum allowable torque and service life. Wear is dependant on lubrication.We recommend that each user compute their own values based on actual operating conditions and test in application.
Delrin POM 50%*60°C
PEEK GF30®55 - 65%*
80°CMaximum torque as % of CA104 Aluminium Bronze WheelMaximum Wheel Temperature
Working characteristicsof driving machineUniformLight ShocksModerate ShocksHeavy Shocks
Uniform1.001.101.251.50
Light Shocks1.251.351.501.75
Moderate Shocks1.501.601.752.00
Heavy Shocks1.751.852.002.25+
Working characteristics of driven machine
* Approximate value based on plastic wheel running with steel worm to allow initial selection. Testing in application will be required.Torque for anti backlash wormwheel gears is limited by the spring rating. Please contact our Technical department for details.When selecting gears application factors should be applied to required torque. T2 > Trequired x Ka Application factor Ka
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Coefficient of friction µ (Mineral Oil)Velocity
Range(m/s)
0.0-0.91.0-1.92.0-2.93.0-3.94.0-4.95.0-5.96.0-6.97.0-7.98.0-8.99.0-9.9
10.0-10.911.0-11.912.0-12.913.0-13.914.0-14.915.0-15.916.0-16.917.0-17.918.0-18.919.0-19.920.0-20.921.0-21.922.0-22.923.0-23.924.0-24.925.0-25.926.0-26.927.0-27.928.0-28.929.0-29.9
30.0
00.15000.04380.03290.02760.02420.02190.02020.01870.01760.01690.01610.01550.01490.01460.01430.01410.01390.01370.01350.01340.01320.01310.01300.01290.01280.01270.01260.01250.01240.01230.0123
0.10.08030.04230.03220.02720.02390.02170.02000.01860.01750.01680.01600.01540.01490.01460.01430.01410.01380.01360.01340.01330.01310.01300.01290.01290.01280.01270.01260.01250.01240.0123
-
0.20.06940.04100.03160.02680.02360.02150.01990.01850.01740.01660.01590.01540.01490.01460.01430.01410.01380.01360.01340.01330.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.30.06230.03960.03090.02650.02340.02140.01970.01840.01730.01660.01590.01530.01480.01450.01420.01400.01380.01360.01340.01330.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.40.05830.03820.03040.02610.02320.02120.01960.01830.01730.01640.01590.01530.01480.01450.01420.01400.01380.01360.01340.01330.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.50.05430.03690.02970.02570.02290.02100.01940.01820.01720.01640.01580.01520.01470.01440.01420.01390.01380.01360.01340.01330.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.60.05210.03590.02930.02540.02260.02090.01930.01810.01720.01640.01570.01510.01470.01440.01420.01390.01370.01350.01340.01320.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.70.05000.03520.02890.02510.02240.02070.01920.01790.01700.01630.01560.01510.01470.01440.01420.01390.01370.01350.01340.01320.01310.01300.01290.01280.01270.01260.01250.01240.01240.0123
-
0.80.04800.03440.02860.02480.02230.02050.01900.01780.01690.01620.01560.01500.01460.01440.01410.01390.01370.01350.01340.01320.01310.01300.01290.01280.01270.01260.01250.01240.01230.0123
-
0.90.04590.03360.02800.02450.02210.02030.01890.01770.01690.01620.01560.01500.01460.01440.01410.01390.01370.01350.01340.01320.01310.01300.01290.01280.01270.01260.01250.01240.01230.0123
-
µ for Velocities 0-30m/s
Example: if Vg = 1.2 then µ = 0.0410
Worms & Wheels
EfficiencyThe following allows an approximate value for the efficiency of the gears to be found allowing required input torque and gearforces to be calculated. Efficiency is dependant on lubrication and the figures below do not include bearing, seal and other losses.
h = tan l / tan (l+ pz)pz = arctan (µ)vg = (d1 · n1) / (19098 . cos l)T1 = (T2 / u) * h
T1 = Input Torque (Nm)T2 = Output Torque (Nm)u = Ratioh = Efficiencyl = Lead Angle (degrees)m = Coefficient of Frictionpz = Angle of Frictionvg = Sliding Velocity (m/s)n1 = rpm of Wormd1 = Reference Diameter of Worm (mm)
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Ftm1 = 2000* (T1 / d1) = - Fxm2Ftm2 = 2000* (T2 / d2) = - Fxm1Frm1 = Ftm1* [tan 20 / (sin l + pz) ] = - Frm2
pz = arctan (m)Ftm = Tangential force (N)Fxm = Axial force (N)Frm = Radial force (N)When working with a gear set, the subscript 1 denotes a worm and 2 a wormwheel.
Ondrives worm and wheel gears are supplied right hand lead as standard.The arrows show the direction of rotation.
Ftm1 = -Fxm2
Worms & Wheels
Gear Forces and Direction of Rotation
Frm1 = -Frm2
Ftm2 = -Fxm1
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
da
F
hahf
d1
d2
d
X
Re
Bevel Gears
Description Symbol Unit EquationNormal Module mn Pressure Angle a degrees = 20°Shaft Angle S degrees = (90° for Ondrives standard gears)Number of Teeth z1, z2Gear Ratio u = z2 / z1Pitch Diameter of Worm d1, d2 mm = z · mnPitch Cone Angle d1 degrees = d1 = tan-1 (sin S / (u + cos S))Pitch Cone Angle d2 degrees = d2 = S - d1Cone Distance Re mm = d2 / 2 sin d2Addendum ha mm = 1.00 · mn (for Ondrives standard gears)Dedendum hf mm 0.6 to 1.0mn = 1.25 · mn (standard gears) 1.5 to 2.0mn = 1.22 · mn (standard gears) 4.0mn = 1.20 · mn (standard gears)Outside Diameter da mm = d + 2 ha · cos dPitch Apex to Crown X mm = Re cos d - ha sin d
Quality Grade 7 DIN 3965
TorqueStated value is maximum torque (T2) based on two identical gears with the same number of teeth running at standard centres. Value is minimum from surface stress or bending stress.Other factors including duty cycle and temperature will affect maximum allowable torque and service life.Wear is dependant on lubrication.We recommend that each user compute their own values based on actual operating conditions and test in application.
MaterialsInput SpeedBending Stress Factor SbSurface Stress Factor Sc
817M40
32,000 3,000
805M20
50,00011,000
303 Stainless
20,000 1,800
316 Stainless
15,800 1,400
100 rpm Uniform, 12 hours running per day
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R SMaterials
Material Equivalents
Ondrives can manufacture gears in a range of additional materials including bronzes, engineering plastics, special steels and stainless steels.Gears can be heat treated by a range of methods to improve performance.Please contact our Technical sales team who will be happy to discuss your specific requirements.
Material805M20
817M40T080M40
722M24T303S21316S1617-4PHCA104
PB2Brass CZ121PEEK GF30Delrin POM
Cast Iron GG25Titanium Ti-6AL-4V
Case Hardened
Nitride HardenedCold DrawnCold DrawnCondition A
Sand Cast
Continuous CastGrade 5
Density(Kg/m3)
7,8507,8507,8507,8508,0008,0007,7807,5808,6008,4701,4901,4107,2004,420
Elongationafter
Fracture11%
5 - 13%7 - 17%
13%35 - 45%
40%10%15%5%
20%2.7%30%
-10 - 18%
TensileStrength(N/mm2)
980850 - 100510 - 600850 -1000480 - 510
5151103 750
360 - 500410156 67
145 - 195895 -1000
0.2% ProofStress
(N/mm2)785680340650
180 - 200205100430
170 - 280200
---
828 - 910
B.S. 970 817M40T805M20303S21316S16080M40655M13722M24
PB2CA104
Brass CZ121
B.S. 1452Cast Iron 250
Titanium Ti-6AL-4V
En24T3625858J8
3640B
ISOCu89Sn11
GZ-CuAL10NiCuZn39Pb3
EnEN-GJL-250
B.S.2TA11
DIN40NiCrMo8-4 / 34CrNiMo620NiCrMo2-2 / 20NiCrMo2
X10CrNiS189X5CrNiMo17133
C4014NiCr14
32CrMo12
DINCuSn12
CuAL10Ni-
DINDIN 1691 GG25
UNSR56400
Werkstoff1.6562, 1.6582
1.65231.43051.44361.05111.57521.7361
Werkstoff3.7165
SAE/AISI4340, 4337
8620303316
10403415, 3310, 9314
-
SAE/AISISAE 64
ASTM B150 UNC C63200UNC C38500
AMS4911/4928
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Delrin POM (White)DIN EN ISO 1043-1: POM C | polyacetal comopolymer.
Very good dimensional stabilitycompared to Nylon & Hostaform.Minimal absorption of moisture.
Good sliding properties.High wear resistance.
High surface hardness.High mechanical strength and stiffness
compared to Nylon & Hostaform.Can be in contact with food (FDA).
Delrin gears can be run dry or greased/oiledto improve wear.
PEEK GF30® (Light Brown)DIN EN ISO 1043-1: PEEK | polyetheretherketone.
Excellent dimensional stability.Outstanding high mechanical strength and hardness
over a broad temperature range.Shows only a slight distortion under the impact of
mechanical load and high temperature.Good electrical insulating properties.
Extremely high flame resistance.Self-extinguishing.
Very low smoke emission in a case of a fire.Can be run dry for slow speed hand operation.
Gears should be greased/oiled for all other operating conditions.
General PropertiesDensityAbsorption of MoistureMechanical propertiesYield Stress/ Tensile StrengthElongation at BreakTensile Modulus of ElasticityBall Indentation HardnessShore - HardnessCoefficient of Friction against hardened and ground steel (dry)Thermal PropertiesMelting TemperatureThermal Properties Coefficient of Linear Thermal ExpansionService Temperature, long term (min.)Service Temperature, long term (max.)Service Temperature, short termHeat Deflection TemperatureElectrical Properties Dielectric Constant Dielectric Dissipation FactorSpecific Volume ResistivitySurface ResistivityComparative Tracking Index (test solution A)Dielectric Strength
kg/m3
N/mm2
N/mm2
N/mm2
Skala D
°CW / (m · K)
10-6 K-1
°C°C°C°C
W · cmW
kV/mm
Delrin POM 14100.20%
6730.0%2800 150 81
0.10-0.30
1650.31110 -50100140110
3.800.00210131013 600 40
PEEK GF30®14900.14%
1562.7%9700 230 88
0.38-0.46
3430.43 30 -20250310315
3.200.00110141013 175 20
Materials
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
The backlash figures given for spur, helical and crossed axis helical gears is the theoretical backlash for two identical gears at standard centre distance to the ISO 286 centre distance tolerance.It is given as circumferential backlash in mm measured on pitch circle diameter. An upper and lower value is quoted.Theoretical backlash is the difference between tooth thickness without and with tolerance applied.Backlash is calculated according to DIN 3967Ondrives can manufacture gears to a wide range of tolerances to suit customer application.Please contact our Technical Sales team who will be happy to discuss your specific requirements.Tooth Thickness Tolerances
Asn = Tooth thickness allowance which is the difference between measured gear tooth thickness and theoretical value measured in the normal section.
When working with a pair of gears the subscript 1 and 2 denotes input (drive) and output (driven) gear. For worm and wheel, 1 relates to the worm and 2 to the wormwheel. The subscript e is for upper allowance and i for lower allowance.Tsn = Tooth thickness tolerance measured in the normal section. (mm)Asne = Sn – SneAsni = Asne – Tsn = Sn – Sni
Circumferential Backlash jtThis is the length of arc on the pitch circle diameter through which each can be rotated whilst the other is held stationary.It is measured in the transverse section.
Units = mm & degrees
Normal Backlash jnThis is the shortest distance between the flanks of the gears when the opposite flanks are in contact.It is measured in the transverse section.For spur, helical, crossed axis helical gear Units = mm & degrees
Change in Circumferential due to Centre Distance Tolerance Dja Units = mm & degrees
Deviation from Centre Distance
As (mm)0.0010.0100.0150.0200.0250.0300.0350.0400.0450.050
Change inBacklashDja (mm)
0.0010.0070.0110.0150.0180.0220.0250.0290.0330.036
Deviation from Centre Distance
As (mm)0.0010.0100.0150.0200.0250.0300.0350.0400.0450.050
Change inBacklashDja (mm)
0.0010.0080.0110.0150.0190.0230.0260.0300.0340.038
Deviation from Centre Distance
As (mm)0.0010.0100.0150.0200.0250.0300.0350.0400.0450.050
Change inBacklashDja (mm)
0.0010.0100.0150.0210.0260.0310.0360.0410.0460.051
Spur Gear Parallel Helical Gear Crossed Axis Helical Gear
Backlash
Gear TypeSpur
Spur (Skive hobbed)Pinion
Parallel HelicalCrossed Axis Helical
Worm & WormwheelGear Type
Bevel
Module 0.5 to 0.87e/8e DIN 58405
6e DIN 584057e DIN 584057e DIN 584057e DIN 58405
7e/8e DIN 58405Module 0.6 to 4.07f24 DIN 3965/3967
Module 1.0 to 3.0e25 DIN 3967e25 DIN 3967e25 DIN 3967e25 DIN 3967e25 DIN 3967e25 DIN 3967
Centre Distance Tol.Js7Js7
-Js7Js8Js8
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
*Asne is converted from base tangent length allowance (Aw) according to Aw = Asn * cos 20°
e25 DIN 3967
7e DIN 58405
Angular Backlash jq Units = mm & degrees
d2 = Reference diameter (mm)As = Centre distance tolerance (i.e. a = 30mm Js7, As = ±0.0105mm)an = Normal pressure angle (an = 20°)b = Helix angle (b = zero for spur gears) Replace helix angle b with lead angle l for worm and wheel.1° = 60 arc minutes
360 x p x d2
Backlash
Reference Diameterd (mm)
Over Upto
Upper ToothThickness Allowance
Asne
ToothThickness Tolerance
Tsn - 10 10 50 50 125 125 280
-0.022mm-0.030mm-0.040mm-0.056mm
0.020mm0.030mm0.040mm0.050mm
Reference Diameterd (mm)
NormalModule
msn
Upper ToothThickness Allowance
Asne
ToothThickness Tolerance
Tsn
from 3 to 6
>6 to 12
>12 to 25
>25 to 50
>50 to 100
>100 to 200
>200 to 400
>0.16 to 0.25>0.25 to 0.6>0.6 to 1.6
>0.16 to 0.25>0.25 to 0.6>0.6 to 1.6
>0.16 to 0.25>0.25 to 0.6>0.6 to 1.6>1.6 to 3
>0.16 to 0.25>0.25 to 0.6>0.6 to 1.6>1.6 to 3
>0.16 to 0.25>0.25 to 0.6>0.6 to 1.6>1.6 to 3
>0.6 to 1.6>1.6 to 3
>0.6 to 1.6>1.6 to 3
0.0280.0300.0350.0300.0350.0400.0350.0400.0450.0500.0400.0450.0500.0550.0450.0500.0550.0630.0630.0700.0700.080
0.0110.0120.0140.0120.0140.0160.0140.0160.0180.0200.0160.0180.0200.0220.0180.0200.0220.0240.0240.0290.0290.032
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Example for Calculating Backlash for Two Non-Identical GearsInput Gear PSG0.5-20 7eOutput Gear PSG0.5-40 7e1. Calculate the reference diameter d for each gear PSG0.5-20 d1 = z * mn = 10.00mm PSG0.5-40 d2 = 20.00mm2. Find Asne and Tsn from the tables overleaf PSG0.5-20 Asne = -0.035mm Tsn = -0.014mm PSG0.5-40 Asne = -0.040mm Tsn = -0.016mm3. Calculate Asni for each gear PSG0.5-20 Asni = Asne - Tsn = -0.035-0.014 = -0.021mm PSG0.5-40 Asni = Asne - Tsn = -0.040-0.016 = -0.024mm4. Calculate the centre distance of the two gears and the centre distance tolerance centre distance = (10 + 20) / 2 = 15mm Js7 = ±0.009mm5. Calculate the change in backlash due to centre distance
6. Calculate the maximum backlash Remove the minus sign on Asn
7. Calculate the minimum backlash Remove the minus sign on Asn
8. Convert to angular backlash
1° = 60 arc minutes
28.208 to 13.072 arc minutes
0
0
Backlash
360 x p x d2
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
OverInc.
F6
F7
G6
G7
H6
H7
H8
H9
H10
H11
J6
J7
J8
JS6
JS7
JS8
K6
M6
M7
36
18102210124
16480
120
180
300
480
7505
–36
–610–84
–46
–69
–92
–6–1–90
–12
610
22132813145
20590
150
220
360
580
9005
–48
–712
–104.5
–4.57.5
–7.511
–112
–7–3
–120
–15
1018
27163416176
246
110
180
270
430
700
11006
–510–815
–125.5
–5.59
–913.5
–13.52
–9–4
–150
–18
1830
33204120207
287
130
210
330
520
840
13008
–512–920
–136.5
–6.510.5
–10.516.5
–16.52
–11–4
–170
–21
3040
4050
5065
6580
80100
100120
120140
140160
6843834339145414250
400
630
1000
1600
2500
18–726
–1441
–2212.5
–12.520
–2031.5
–31.54
–21–8
–330
–40
160180
180200
200225
7950965044156115290
460
720
1150
1850
2900
22–730
–1647
–2514.5
–14.523
–2336
–365
–24–8
–370
–46
225250
41255025259
349
160
250
390
620
1000
1600
10–614
–1124
–158
–812.5
–12.519.5
–19.53
–13–4
–200
–25
4930603029104010190
300
460
740
1200
1900
13–618
–1228
–189.5
–9.515
–1523
–234
–15–5
–240
–30
5836713634124712220
350
540
870
1400
2200
16–622
–1334
–2011
–1117.5
–17.527
–274
–18–6
–280
–35
Hole Sizes (mm)
Micrometres (10-3m)
Limits and Fits
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
OverInc.
f6
f7
g5
g6
g7
h6
h7
h8
h9
h10
h11
j6
j7
js5
js6
js7
k6
m6
m7
36
–10–18–10–22–4–9–4
–12–4
–160
–80
–120
–180
–300
–480
–756
–28
–42.5
–2.54
–46
–691
124
164
610
–13–22–13–28–5
–11–5
–14–5
–200
–90
–150
–220
–360
–580
–907
–210–53
–34.5
–4.57.5
–7.5101
156
216
1018
–16–27–16–34–6
–14–6
–17–6
–240
–110
–180
–270
–430
–700
–1108
–312–64
–45.5
–5.59
–9121
187
257
1830
–20–33–20–41–7
–16–7
–20–7
–280
–130
–210
–330
–520
–840
–1309
–413–84.5
–4.56.5
–6.510.5
–10.5152
218
298
3040
4050
5065
6580
80100
100120
120140
140160
–43–68–43–83–14–32–14–39–14–54
0–25
0–40
0–63
0–100
0–160
0–250
14–1122
–189
–912.5
–12.520
–20283
40155515
160180
180200
200225
–50–79–50–96–15–35–15–44–15–61
0–29
0–46
0–72
0–115
0–185
0–290
16–1325
–2110
–1014.5
–14.523
–23334
46176317
225250
–25–41–25–50–9
–20–9
–25–9
–340
–160
–250
–390
–620
–1000
–16011–515
–105.5
–5.58
–812.5
–12.5182
259
349
–30–49–30–60–10–23–10–29–10–40
0–19
0–30
0–46
0–74
0–120
0–190
12–718
–126.5
–6.59.5
–9.515
–15212
30114111
–36–58–36–71–12–27–12–34–12–47
0–22
0–35
0–54
0–87
0–140
0–220
13–920
–157.5
–7.511
–1117.5
–17.5253
35134813
Hole Sizes (mm)
Micrometres (10-3m)
Limits and Fits
TE
CH
NIC
AL
Product information updated March 2017 and subject to change. Please click the product links for prices and availability.
P R E C I S I O N G E A R S
Keyways to DIN 6885 Js9 sliding fit. D10 free fit and P9 tight fit available on request.Woodruff keyways available on request.Standard bore tolerance H7 ISO 286. Other tolerances available.Special bore shapes available including square and hexagon.
t1
t2
b r
r
h
Modifications
Bore Size dOver
- 6 810121722303844
Bore Size dIncluding
6 81012172230384450
Keyway Sizeb x h
- 2 x 2 3 x 3 4 x 4 5 x 5 6 x 6 8 x 710 x 812 x 814 x 9
PinHole 1.5 2.0 3.0 4.0 5.0 6.0 8.010.010.010.0
TappedHole
M3 x 0.5 M3 x 0.5 M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1.0 M8 x 1.25 M10 x 1.5 M10 x 1.5 M12 x 1.75
Shaft t1 Bore t1Width Depth
Keyb x h2 x 23 x 34 x 45 x 56 x 68 x 7
10 x 812 x 8
Shaft bN9
-0.004/-0.029-0.004/-0.029+0.000/-0.030+0.000/-0.030+0.000/-0.030+0.000/-0.036+0.000/-0.036+0.000/-0.043
Bore bJs9
+0.012/-0.012+0.012/-0.012+0.015/-0.015+0.015/-0.015+0.015/-0.015+0.018/-0.018+0.018/-0.018+0.021/-0.021
Nominal1.21.82.53.03.54.05.05.0
Tolerance+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.20/–0.00+0.20/–0.00+0.20/–0.00
Nominal1.01.41.82.32.83.33.33.3
Tolerance+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.10/–0.00+0.20/–0.00+0.20/–0.00+0.20/–0.00
Radiusr
Max – Min0.16 – 0.080.16 – 0.080.16 – 0.080.25 – 0.160.25 – 0.160.25 – 0.160.40 – 0.250.40 – 0.25