Date post: | 10-Apr-2018 |
Category: |
Documents |
Upload: | jose-gallardo |
View: | 220 times |
Download: | 0 times |
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 1/12
Low capacityDigital Radio System
SRAL XD
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 2/12
Contents
Applications
Main features
System architecture
Installation &maintenance
Management
Technical data
market indications and trends, adds
to its extensive microwave portfolio
the new line of point to point low
capacity digital radio: SRAL XD.
Siemens expertise covers most of theoutstanding technologies which
current applications are based on:
switching, cellular technology, radio
and networking, voice and data over
IP and ATM.
An outstanding turnkey project
management capability, the ownership
of a so wide range of in-house product
lines and a worldwide field proven
experience, represent the unequaled
Siemens business card.
Microwave systems cover most
of connectivity needs especially in
the lower layers of the transmission
networks, consolidating their role
of reliable, easy-to-install and cost-effective access solution. Siemens,
used to be one of the frontrunners
in this market segment, is ready to
match the expectations of the new
incoming telecommunication era
characterized by broadband and
mobility convergence.
Nowadays, the new challenge
launched by operators aims to
increase link density and capacity,
leaving spectrum occupancy
practically unchanged.Siemens, always ready to acknowledge
3G Cells
2G Cells
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 3/12
A wide-range of applications is
possible, particularly since voice
and data can be transmitted over
the same microwave link.
A typical scenario is an enterprisewith a branch office located at some
distance from the main premises.
Service convergence is the word
summarising the trend of this kind
of network, and once again flexibility
becomes a must even in this case.
SRAL XD line is primarily designed forurban networks, but is also suitable
in regional networks meeting all the
requirements of access and trunk
applications.
• Mobile Networks: in the 3G Mobile
ATM based network, typically SRAL XD
is used to collect traffic conveying
from NodeB to Hub stations; in the
2G networks it is already implemented
to provide access to core networks.
In the next future, the overlay
of the two mobile networks will
certainly benefit from SRAL XD
upgrading facilities, rewarding
operators with flexible and versatile
infrastructures.
• Fixed services Networks: SRAL XD
supports ATM/IP networks, LAN
and WAN.
Applications
Other MobileOperators
PSTN/ISDN
Public Internet
EnterpriseIntranetHQ
Branch Office
IP LAN
MSC
SGSN
GGSN
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 4/12
MinIDU solution
Add/Drop and Crossconnection
functionalities enrich the set of SRAL XD
features: any E1 stream plugged in
the near end terminal can be
extracted from any E1 connector
of the far end terminal, eliminating
the need of bulky distribution frames.
Furthermore, the Add/Drop facility
permits to drop the required E1 in
station leaving the remaining streams
passing untouched.
Based on network specific needs, the
operator can select either higher
spectrum efficiency or higher system
gain and hop lengths.
All the parameters can be software
selected locally or remotely in order
to adapt the hardware platform to
each single link characteristic in
terms of available RF channel,
payload, usable bandwidth and hop
length.SRAL XD flexibility and versatility
greatly optimize all the upgrading
procedures and configuration
changes. A terminal can be easily
relocated without any hardware
modification simply re-shaping its
peculiar parameters on the new link
requirements.
Another important strong advantage
is represented by the extreme
compactness of SRAL XD Indoor Unit.
A single 44 mm high unit is sufficientto implement any protected or
unprotected terminal configuration,
minimising the impact of
transmission equipment. But SRAL
XD family offers further possibilities
in order to face the problem of
station footprint, the most
troublesome matter for network
planners: integrating the indoor card
BTSs/ NodeBs for operators using
Siemens integrated solution.This solution combines BTS/NodeB
and transmission in the same shelf,
eliminating any additional room
allocation for transmission systems.
Main features
Automatic Transmitter Power Control
has been implemented to increase
the system performances, reducing
power consumption and interference
in crowded nodes; ATPC function can
be switched off, setting the
transmitted power to a fixed value
included in the ATPC interval.
BTS/NodeB rack
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 5/12
System architecture
SRAL XD equipment is available in
Split Indoor and Outdoor Configuration;
both the IDU and the ODU have been
redesigned in order to reduce their
mechanical dimension respect to
the previous SRA L generation of PDH
microwave equipment. In fact, in
order to save room for the indoor
installation, the dimensions of the
IDU have been dramatically reduced,
moving the mo/demodulationsection to the ODU. As a result the
IDU able to provide protected
configurations is only 1U high.
In spite of this change the
dimensions of the ODU have been
reduced as well by adopting the state
of the art technology.
MinIDU
Plug-in IDU
SingleBoard IDUMinIDU
Plug-in IDU
SingleBoard IDU
ND ODUHD/HP ODU
Three different IDU families are
available in order to provide
respectively tailored configurations,
cost-effective solution, maximum
flexibility and integration into
Siemens NodeB/BTS racks:
• SingleBoard
• Plug-in
• MinIDU
Normal DensityHigh Density/High Performance
Each version, being independent
from modulation format and
frequency bands, is able to
manage either High or Normal
Density arrangements.
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 6/12
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 7/12
State of art RF technology has been
the baseline for SRAL XD ODUs
development, completely matching
all the technical constraints
introduced by the high modulation
scheme adopted for the HD version:
system linearity and synthesizer
phase noise.
Two different outdoor units, capacity
independent, are part of SRAL XD
suit:
ODU ND:
is the appropriate solution for
normal density arrangement,
able to achieve the best compromise
between performance and power
consumption by exploiting a
constant amplitude modulation
format (4 CPM).
ODU HD/HP:
born for high density arrangements,
the same equipment is capable to
perform normal density arrangement
as well thanks to software selection
of the relevant modulation format.The adoption of Trellis Code
Modulation leads to Rx threshold
level unmatched by a plain 16 QAM
modulation.
OUTDOOR UNITS
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 8/12
SRAL XD has been engineered to
simplify to the maximum extent all
the operations related to the system
such as installation, maintenance,
upgrading and supervision.
Configuration settings, system
upgrades can be remotely performed
with software downloads, without
the need of sending technicians on site.
The compact size and reduced weight
of the Indoor Units, Outdoor Unitsand antennas allow a faster and
easier deployment, together with a
reduced environmental impact.
The Outdoor unit can be directly
mounted on the rear of the antenna,
avoiding the use of any waveguide.
Several mounting structures, holding
one or two ODUs, are available for
integrated or separated ODU-antennaconnections.
Moreover, the IDU hosts an extractable
“Memory Key” in which the configuration
For SRAL XD product line, system
concept and embedded software
architecture have been designed to
allow an user-friendly and effective
local and remote terminals’
management.
SRAL XD Indoor Unit offers a wide
range of management and service
interfaces, together with enhanced
routing functionalities: the
combination of these new features
dramatically improves SRAL XD
interworking capabilities to fit any
DCN requirement.
SRAL XD, as all Siemens microwave
product lines, can be managed not
only by the existing Microwave
Installation &
maintenance
Management
of the system is contained. The use of
this key allows an easy ‘in field’
replacement of the IDU without
the use of the LCT, as well as off-line
initial software configurations
without any need for settingparameters during the installation.
Siemens NMS (NetViewer) but also
by third party Management Systems:
open interfaces are available to
integrate SRAL XD and all the other
Siemens Microwave Radiotransmission equipment in
multivendor transmission networks.
SRAL XDnetwork
SRAL XDnetwork
IP DCN
Third partynetwork
Third party
network
TMN channel
framed in2Mbit/s tributary
Ethernet
TMN channel
framed in2Mbit/s tributary
D-ext
channel
D-ext
channel
Ethernet
Ethernet
NetViewer
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 9/12
NetViewer
The Microwave Management System
NetViewer is a versatile TMN product
for the management of PDH, SDH and
Point-to-Multipoint microwave
systems, able to supervise other
vendors’ devices as well through a
standard SNMP interface. An overall
view of the complete network
structure and its ability to enter down
to the Network Element details give aclear picture of the whole network, its
configuration and events. Fault,
Configuration and Performance
management are carried out at
Network Element level; at Network
level Fault and Security configuration
are available.
Netviewer is the basic part of Siemens
offer for Network Management
oriented to microwave networks that
is represented by the NetViewer NME
Suite.
The suite is composed of a number of
modules:
• NetViewer, core of the system, as
Element Manager;
• SNMP Agent, a real-time
northbound interface;
• TCOA (TMF CORBA Agent), a real-
time northbound interface;
• NML module, as Network Manager;
• HP OpenView NNM (Network Node
Manager) add-on, that allows theintegration of NetViewer in HP;
OpenView NNM (product of Hewlett
Packard);
• HP-Compaq TeMIP add-on, that
allows the integration of NetViewer
in HP OpenView TeMIP (product of
HP-Compaq).
Moreover, NetViewer can be easily
integrated both in Siemens SDH TMN
platform (TNMS) with TNMS Core
Radio add-on, and in Mobile TMN
platform (Radio Commander) in order
to offer to the operator a unique
interface for management purposes.
Business
Management
Service
Management
Network
Management
ElementManagement
Fault Management
Configuration Management
Accounting Management
Performance Management
Security Management
NetViewer
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 10/12
Technical data
SYSTEM PARAMETERS
RF Bands 7/8 GHz 7.1-8.5 GHz
13 GHz 12,75-13,25 GHz
15 GHz 14.4-15.35 GHz
18 GHz 17.7-19.7 GHz
23 GHz 21.2-23.6 GHz
26 GHz 24.5-26.5 GHz
28 GHz 27.5-29.5 GHz
32 GHz 31.8-33.4 GHz
38 GHz 37.0-39.5 GHz
Channel Arrangements Normal Density High Density/High Performance
Modulation 4CPM 4QAM 16TCM
Capacity 2xE1 4xE1 8xE1 16xE1/E3 2xE1 4xE1 8xE1 16xE1/E3 8xE1 16xE1/E3
Channel Spacing (MHz) 3,5 7 14 28 3,5 7 14 28 7 14
RSL@ BER 10-3 (dBm)Typical Values
7GHz -94 -91 -88 -84 -95 -92 -89 -86 -88.5 -85.5
8GHz -94 -91 -88 -84 -94 -91 -88 -85 -87.5 -84.5
13GHz -93.5 -90.5 -87.5 -83.5 -94.5 -91.5 -88.5 -85.5 -88 -8515GHz -93.5 -90.5 -87.5 -83.5 -94.5 -91.5 -88.5 -85.5 -88 -85
18GHz -93 -90 -87 -83 -93.5 -90.5 -87.5 -84.5 -87 -84
23GHz -92.5 -89.5 -86.5 -82.5 -93 -90 -87 -84 -86.5 -83.5
26GHz -92 -89 -86 -82 -92 -89 -86 -83 -85.5 -82.5
28GHz -91.5 -88.5 -85.5 -81.5 -92 -89 -86 -83 -85.5 -82.5
32GHz -91 -88 -85 -81 -91.5 -88.5 -85.5 -82.5 -85 -82
38GHz -91 -88 -85 -81 -91.5 -88.5 -85.5 -82.5 -85 -82
Output Power (dBm)Typical Values
7GHz 24 23 18
8GHz 24 22 1713GHz 20 22 17
15GHz 20 20 15
18GHz 18 24 19
23GHz 18 20 15
26GHz 18 20 15
28GHz 18 20 15
32GHz 17 19 14
38GHz 17 17 12
Output Power 24 for 7 to 23 GHzSetting Range (dB) 20 for 26 to 38 GHz 20 15
Power Consumption 1+0 terminal: 30W(max) 1+1 terminal: 50W
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 11/12
INDOOR UNIT
IDU Plug-in IDU SingleBoard MinIDU
Tributary Interfaces Up to 32x2 Mbit/s E1 Up to 16x2 Mbit/s E1 Up to 16x2 Mbit/s E134 Mbit/s E3
4xEthernet 10/100 Base T
Physical Interfaces Electrical, G.703 Electrical, G.703 Electrical, G.703Ethernet 10/100 Base T
Auxiliary Interfaces 2 x 10/100 BaseT-TMN channels 2 x 10/100 BaseT-TMN channels 2 x 10/100 BaseT-TMN channel2 x V.11 co/contradirectional 1 x V.11 co/contradirectional user or TMN channel
user or TMN channel user or TMN channel IUB/ABIS tracersRS-232 LCT interface RS-232 LCT interface 2x10/100 NodeB TMN channels
RS-232 LCT interface
Dimensions HxWxD 44 x 430 x 240 mm 44 x 430 x 240 mm 85 x 240 x 130 mm
Weight 1,5 kg 1,5 kg 2 kg
Power Supply Voltage -48 V ± 20 %
Temperature -5 ÷ +55 °CRange (ETS 300 019-1-3, class 3.2)
OUTDOOR UNITODU ND ODU HD/HP
Dimensions 230x230x110 mm 270x270x150 mm(HxWxD)
Weight 4,5 kg 7,5 kg
Temperature -33 ÷ +55 °CRange (ETS 300 019-1-4, class 4.1)
8/8/2019 sralxdbrochure
http://slidepdf.com/reader/full/sralxdbrochure 12/12
Siemens Mobile Communications S.p.A.Sales OfficeViale P. e A. Pirelli, 1020126 Milano - Italy
Phone + 39 02 243 1
F4.1 1765/1000 • Siemens Mobile Communications Spa
Printed in Italy
This publication is issued to provide information only and is not to form
part of any order or contract. The products and services described herein
are subject to availability and to change without notice.
www.siemens-mobile.com
Acronyms and AbbreviationsATM Asynchronous Transfer Mode
ATPC Automatic Transmitter Power Control
BTS Base Transceiver Station
CPM Continuous Phase Modulation
DCN Data Communication Network
IDU Indoor Unit
LCT Local Craft Terminal
NMS Network Management System
ODU Outdoor Unit
PDH Plesiochronous Digital Hierarchy
QAM Quadrature Amplitude Modulation
RF Radio FrequencySDH Synchronous Digital Hierarchy
SNMP Simple Network Management Protocol
TCM Trellis Code Modulation
TMN Telecommunication Management Network