15
SRAM RED ® eTap ® JUNE 21, 2016 SRAM RED ® eTAP ® AERO SETUP OPTIONS
SRAM RED® eTap®
JUNE 21, 2016
SRAM RED® eTAP®
AERO SETUPOPTIONS
TRI eTAP®
A primary goal throughout the development of SRAM RED® eTap® was to create a shifting solution for triathletes that delivered the lowest weight and best aerodynamics of any electronic groupset available as well as unmatched shifter setup versatility. With shift buttons placed exactly where you want them, on both the base bar and the extensions, you can maintain your position more comfortably while focusing on the road ahead and giving your best effort. Plus, the groupset’s wireless shifting not only makes initial installation simple on any bike, it makes disassembly/reassembly for travel far easier as well.
While setup possibilities are limitless, we’ve found that there are a few eTap® installation options that most triathletes prefer. Here we’ll review popular shift button placement options using SRAM Blips, BlipGrips™, and eTap® Clics™ shifter buttons. Regardless of which shift buttons you choose, they all plug into the required BlipBox™ shifter, so we’ll also look at a few BlipBox™ mounting options.
SRAM RED® eTap®
JUNE 21, 2016
BlipGrips™
BlipBox™
eTap® Clics™
Blips
SRAM RED® eTap®
JUNE 21, 2016
BASE BAR SHIFTER SETUP
A key advantage of eTap® is that Blip shift buttons can be placed on both the aero extensions and base bar. With the ability to shift on the base bar, triathletes can save time getting up to speed after exiting the transition area and execute shifts when riding through tight corners, descending steep roads that require braking, or when climbing out of the saddle. While you can place Blips™ anywhere you want them on the base bar using the supplied double stick tape, here are a couple of popular options:
Riders that prefer shifting with their thumbs typically place Blips™ on the inboard side of the base bar grips, just behind the brake lever mounting point.
For shifting with index fingers, place the Blips™ on the underside of the base bar’s grip area near the brake lever mounting point.
SRAM RED® eTap®
JUNE 21, 2016
Blips shown installed on inboard side of base bar handle with tape installed.
BASE BAR SHIFTER SETUP
If you prefer a tape-free Blip setup on your base bar, our optional BlipGrips™ (available separately) can also be installed in this location and rotated to the position of your choice. Then simply lock them in place using the integrated aluminum clamp.
Regardless of which setup you choose, the 450mm length Blip wire option is typically best.
SRAM RED® eTap®
JUNE 21, 2016
BlipGrips shown installed on inboard side of base bar handle.
AERO EXTENSION SETUP
Most triathletes prefer the plug and play nature of eTap® Clics™ and BlipGrips™ (both are available separately from the eTap® groupset). Either option you choose offers a straightforward installation that doesn’t require any tape. In the case of eTap® Clics™, you don’t even need tools, just thread the wire through the extension and press the button into the end.
SRAM RED® eTap®
JUNE 21, 2016
eTap Clics installed without handlebar tape. eTap Clics installed with handlebar tape.
AERO EXTENSION SETUP
BlipGrips™ can be rotated and positioned in any orientation on the extensions and are easily installed by tightening a single bolt on each grip clamp with a 2.5mm hex wrench.
SRAM RED® eTap®
JUNE 21, 2016
Blip Grips shown with upward oriented Blips on the aero extensions.
AERO EXTENSION SETUP
For riders that want even more installation options, Blips offer the ability to choose any location on the extension to shift from. With that said, the most common mounting options are to place Blips either on the top or inboard side of the extensions for actuation with the thumb.
For index finger actuation, placing the Blip underneath the extension is generally preferred.
Whether you choose eTap® Clics™, BlipGrips™, or standard Blips, the 650mm length wire option is typically best.
SRAM RED® eTap®
JUNE 21, 2016
Blips shown installed on the inboard side of the aero extension without tape. Blips shown on the underside of the aero extension without handlebar tape.
BLIPBOX
The industry standard quarter-turn mount, used for the most popular cycling GPS units, makes installing the eTap® BlipBox™ shifter unit literally a snap. Included in the packaging for the BlipBox™ are four different BlipBox™ mounts to choose from:
• 22.2mm mount that clamps to an aero extension
• Rubber band mount made for attachment to a stem, either on top or on bottom
• Curved bottom adhesive pad for mounting on a curved surface
• Flat bottom adhesive pad for mounting on a flat surface
SRAM RED® eTap®
JUNE 21, 2016
22.2mm mount Rubber band mount
Adhesive backed mounts, curved and flat
BLIPBOX MOUNTING OPTIONS
SRAM RED® eTap®
JUNE 21, 2016
22.2mm mount clamped to aero extension Curved adhesive mount under base bar Curved adhesive mount on stem
BLIPBOX MOUNTING OPTIONS
SRAM RED® eTap®
JUNE 21, 2016
Rubber band mount on top of stem Rubber band mount on underside of stem
BLIPBOX
Additionally, SRAM makes a number of other options for attaching the BlipBox™ to your cockpit setup. These include the SRAM QuickView Computer Mount that attaches to 31.8mm diameter base bars near the stem, the Zipp Vuka BTA Mount with QuickView that allows mounting the BlipBox™ to an aero extension water bottle cage, and the Zipp QuickView TT Computer Mount that attaches to 22.2mm diameter aero extensions.
With all of these options, there is a way to put the BlipBox™ just about anywhere you want it.
SRAM RED® eTap®
JUNE 21, 2016
Zipp Vuka BTA Mount with QuickView
Zipp QuickView TT Computer Mount
SRAM QuickView Computer Mount
SRAM RED® eTap®
JUNE 21, 2016
FEATURES AND BENEFITS
Batteries: attached to the components, removable, and super light (24g). Max 60min charge.
No cables = can be installed on any frame
Multiple setup options = ultimate customization for your needs
Easy and quick to install
Lightest electronic groupset on the market: (77g total for BlipBox & 2 sets of remote shift buttons)
Competitively priced
SRAM RED® eTap®
JUNE 21, 2016
THE CHOICE IS YOURS
When it comes to setting up tri bikes with SRAM RED® eTap®, your imagination is the limit. Whether you choose BlipGrips™, Clics™, or standard Blips, there are no wrong choices here. Bottom line: Your bike is custom fit to you, so why not have your shifting custom fit as well? Get your race bike dialed in and make it uniquely yours with SRAM RED® eTap®.
SRAM RED® eTap®
JUNE 21, 2016
PRICING
PRODUCT PART NUMBER MSRP USA MSRP EU MSRP GBP
Clics for eTap® 650mm Black Qty 2 00.7018.308.000 $110 €120 £95
Clics for eTap® 500mm Black Qty 2 00.7018.308.001 $110 €120 £95
SRAM BlipGrip™ Aero Pair 00.3018.097.000 $20 €20 £15
Blip for eTap® 230mm Black Qty 2 00.7018.210.001 $100 €95 £73
Blip for eTap® 450mm Black Qty 2 00.7018.210.002 $100 €95 £73
Blip for eTap® 650mm Black Qty 2 00.7018.210.003 $100 €95 £73
SRAM eTap® BlipsBox™ 00.7018.235.000 $300 €280 £215
AM RED eTap® 2x11 Groupset Aero 00.3018.120.000 $1,580 €1,475 £1,135
