+ All Categories
Home > Documents > SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin...

SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin...

Date post: 29-May-2018
Category:
Upload: hatuyen
View: 218 times
Download: 0 times
Share this document with a friend
8
©2018 Stillwater Designs SRAMCQ09-20180606 SRAMCQ09 Designed for 2009 -2018 Dodge® Ram vehicles Subwoofer Amplifier Subwoofer Harness Subwoofer Alternate Amp Bracket Subwoofer Power Harness Bolt (only for solid rear bench seat) Fuse Wire Taps Wire Ties x 6 Adapter Harness
Transcript
Page 1: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

©2018 Stillwater Designs SRAMCQ09-20180606

SRAMCQ09 Designed for 2009 -2018 Dodge® Ram vehicles

Subwoofer Amplifier

Subwoofer Harness

Subwoofer

Alternate Amp Bracket

Subwoofer Power Harness Bolt (only for solid rear bench seat) Fuse Wire Taps

Wire Ties x 6 Adapter Harness

Page 2: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

2

Power Harness Routing

1. Disconnect negative battery cable 2. Make sure the supplied fuse is not installed in the fuse holder of the subwoofer power

harness and connect the harness to the stud pictured in Fig. 1. Torque stud nut to 14Nm (124in-lbs)

3. Route the power harness toward the driver’s side factory firewall grommet and secure with the supplied wire ties.

4. Make a small incision in the grommet and pass the power harness into the cabin. Fig. 2

5. Install the black two pin power connector on the subwoofer power harness by first inserting the terminal fully into the connector and then depressing the blue retainer. Fig. 3

Note: Make sure the blue retainer in the center of the connector is not depressed – it should be flush with the front of the connector. If the retainer is depressed, the terminal will not fully seat in the connector body. Make sure the terminal is installed into position 1 on the connector body. There should be a block-out plug installed in position 2 in order to prevent the terminal from being installed into the wrong position on the connector.

6. ground wire for both the subwoofer and amplifier harness. Fig. 11 Torque to 5Nm

Fig 1

Insert terminal

first

Then depress blue retainer Fig 3

Fig 2

Page 3: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

3

Subwoofer Harness Routing

7. Remove the driver’s side kick panel as well as the front and rear sill plate along the bottom of the door opening by snapping loose.

8. Connect the subwoofer harness ground ring to the factory ground point below the steering column. Fig. 4

9. Connect the subwoofer two-pin black power connector to the power harness two-pin connector.

Subwoofer Input Connection with Non-Premium Audio (base audio)

10. Find the gray/yellow striped wire and the gray/purple striped wire in the connector to the left of the brake pedal. For 2009-2012 see Fig. 5, For 2013-present, see Fig. 6

11. Install one of the supplied wire taps on the gray/yellow wire and the gray/purple wire using a

pair of pliers. 12. Connect the two-pin adapter harness to the subwoofer harness and then connect the brown

wire of the adapter harness to the gray/purple wire and the green wire of the adapter harness to the gray/yellow wire.

Subwoofer Input Connection with Kicker Amplifier

13. Connect the white two-pin input connector of the subwoofer harness to the white two-pin connector of the Kicker amplifier harness.

Subwoofer Input Connection with Premium Audio (includes Kicker 12 channel upgrade on 2009-2012)

14. Locate the factory amplifier just below and left of the steering column. Find the gray/brown striped wire and the green/brown striped wire in the 16-pin amplifier connector and install the supplied wire taps with pliers.

15. Connect the brown wire of the adapter harness to the gray/brown wire. Connect the green wire of the adapter harness to the green/brown wire.

16. Connect the adapter harness two-pin connector to the subwoofer input two-pin connector.

Fig 4

Fig 6 Fig 5

Page 4: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

4

Fig 8

17. Route the subwoofer harness along the driver’s side door opening. Route the ten-pin connector under the driver’s seat and out of the existing hole. Fig. 7

Subwoofer Amplifier Mounting without Air Bag Control Module

Note: The Air Bag Control Module is located under the driver’s seat on certain model trucks. The amplifier/bracket assembly as shipped will not install if the Air Bag Control Module is present. If the truck is equipped with the Air Bag Control Module, skip to steps 19-22

18. Remove the two 8mm bolts holding the bracket

for the seat wiring. Mount the amplifier/ bracket assembly as shown in Fig.8 and replace the two 8mm bolts.

Subwoofer Amplifier Mounting with Air Bag Control Module

19. Remove the subwoofer amplifier from its current bracket by removing the four screws and pulling the connector loose. Fig 9

20. Reattach the subwoofer bracket to the alternate bracket using the original screws. Fig. 10

Fig 7

Fig 9 Fig 10

Page 5: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

5

21. Remove the two M6 nuts securing the air ride control module. Fig 11 22. Install the amplifier bracket over the studs and reinstall the M6 nuts. Torque to 5Nm. Fig.12

23. Connect the ten-pin connector of the harness to the amplifier. Slide the red locking tab over

to prevent the connectors from accidentally becoming disconnected. 24. Route the subwoofer four-pin connector toward the rear seat. 25. If the vehicle is equipped with a fold-out cargo tray under the rear seat, the driver’s side

portion will need to be removed to allow the subwoofer to install.

2009-2012 Cargo Tray Removal 26. Remove the four 18mm bolts securing the driver’s side rear seat and remove the seat from

the truck. Fig. 13 27. Remove the plastic cover on the side of the seat. (not necessary on some models) Fig. 14 28. Remove the 13mm and 10mm bolt on both sides of the bottom of the rear seat and remove

the cargo tray. Fig. 15 29. Remove the front latch. (this will not be reinstalled) (not present on one-piece bench seat) 30. Reinstall seat and loosely install the two rear bolts. Fig. 16

Fig 14 Fig 13

Fig 15 Fig 16

Fig 11 Fig 12

Page 6: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

6

2013-present Cargo Tray Removal. 31. Remove the two smaller nuts in the rear. Fig. 17 32. Fold the tray up and remove the two seat bolts and then remove the tray. Fig. 18

33. For vehicles equipped with one piece rear bench seats remove the 18mm bolt securing the driver’s (left) side of the seat to the floor.

34. For one piece rear bench seat you will also need to find threaded nut insert in the floor pan concealed by the carpet flap. Fig. 19

35. Set the enclosure in place and reinstall and tighten all seat bolts and Torque to 30 ft/lbs (a bolt is supplied for one-piece bench seats) Fig. 20

36. Route the subwoofer harness behind the plastic trim panel on the end of the rear seat and

under the driver’s side rear outermost seat bracket. Fig.21 37. Connect the four-pin plug of the subwoofer harness to the subwoofer enclosure. 38. If the vehicle is equipped with a factory subwoofer it must be disconnected for the system to

operate properly. 39. Reinstall all previously removed parts in reverse

order. 40. Install the supplied fuse in the fuse holder under

the hood. 41. Reconnect the negative battery cable. Torque to

5Nm.

Fig 17 Fig 18

Fig 19 Fig 20

Fig 21

Page 7: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

7

Troubleshooting the Kicker Integrated Systems If you experience a problem once the subwoofer or amplifier are installed use this guide to locate the trouble. The radio is working, but the Subwoofer is not working: • Check the battery voltage to make sure it is not discharged below 11 volts. • Check the negative battery cable to see if it has been securely tightened back on the battery. • Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown. • Check the inline +12 volt power connector near the firewall to make sure it is plugged in securely. • Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely. • Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle. • Check the audio input signal connection to make sure it is secure and connected to the proper wiring. • Test with different music in case there is no low frequency audio in the initial sound check.

Symptom Possible Cause Solution

No Subwoofer Output

Fuse not installed in inline fuse holder on subwoofer and / or amp harness

Install fuse into fuse holder. Refer to instructions for correct placement

Low battery voltage Recharge the battery Negative battery cable not connected

Reconnect negative battery cable

Power wire connector not connected to body harness

Connect power wire to body harness. Check for loose connection

Ground wire not grounded properly Check ground wire with voltmeter to insure it is a good

Balance or fader controls not set to neutral position

Set balance and fader control to center settings. (only effects stand-alone subwoofer kit)

No low frequency information in music

Test with several different songs

Subwoofer harness not properly / Completely connected to sub- woofer.

Securely fasten both of the connectors on the subwoofer harness to the subwoofer. Check for loose connections.

Radio Not Coming On Blown radio fuse Refer to owner's manual for

radio fuse location and value Low battery voltage Recharge the battery

Page 8: SRAMCQ09 - kicker.com be a block-out plug installed in ... connector to the power harness two-pin connector. Subwoofer Input Connection with Non-Premium Audio (base audio)

8

If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at (800) 256-0808 ext. 6009, or [email protected].

P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510


Recommended