SECTION 0B

GENERAL INFORMATION

TABLE OF CONTENTSMaintenance And Repair ..................................... 0B-2

Maintenance And Lubrication ............................... 0B-2Normal Vehicle Use ............................................. 0B-2Explanation Of Scheduled

Maintenance Services ....................................... 0B-2Owner Inspections And Services ......................... 0B-3

While Operating the Vehicle ................................. 0B-3At Each Fuel Fill ................................................... 0B-3At Least Twice a Month ....................................... 0B-3At Least Monthly ................................................. 0B-3At Least Twice a Year .......................................... 0B-3Each Time The Oil is Changed ............................. 0B-4

At Least Annually ................................................ 0B-4Standard Bolts Specifications .............................. 0B-5Basic Specification ............................................... 0B-6

Dimension ........................................................... 0B-6Specifications ...................................................... 0B-7Recommended Fluids And Lubricants .................. 0B-9

Vehicle Identification Number System .............. 0B-10Vehicle Identification Number (Vin) ..................... 0B-10ManufacturerS Plate ........................................... 0B-11Engine Number .................................................. 0B-12Vehicle Lifting Procedures .................................. 0B-14

SSANGYONG Y200

0B-2 GENERAL INFORMATION

MAINTENANCE AND REPAIRMAINTENANCE AND

LUBRICATIONNORMAL VEHICLE USEThe maintenance instructions contained in themaintenance schedule are based on the assumptionthat the vehicle will be used for the following reasons: To carry passengers and cargo within the limitation

of the tire inflation prassure. Refer to Tire andWheel in section 2E.

To be driven on reasonable road surfaces andwithin legal operating limits.

EXPLANATION OF SCHEDULEDMAINTENANCE SERVICESThe services listed in the maintenance schedule arefurther explained below. When the fol lowingmaintenance services are performed, make sure allthe parts are replaced and all the necessary repairsare done before driving the vehicle. Always use theproper fluid and lubricants.Engine Oil and Oil Filter ChangeAlways use above the API SH grade or recommendedengine oil.Engine Oil ViscosityEngine oil viscosity (thickness) has an effect on fueleconomy and cold weather operation. Lower viscosityengine oils can provide better fuel economy and coldweather performance; however, higher temperatureweather conditions require higher viscosity engine oilsfor satisfactory lubrication. Using oils of any viscosityother than those viscosities recommended could resultin engine damage.Cooling System ServiceDrain, flush and refill the system with new coolant.Refer to Recommended Fluids And Lubricants inthis section.Air Cleaner Element ReplacementClean the air cleaner element every. Gasoline Engine : 15,000 km (10,000 miles) Diesel Engine : 10,000 km (6,000 miles)

Replace the air cleaner element every. Gasoline Engine : 60,000 km (36,000 miles) Diesel Engine : 30,000 km (18,000 miles)Replace the air cleaner more often under dustyconditions.Fuel Filter ReplacementReplace the engine fuel filter every. Gasoline Engine : 60,000 km (36,000 miles) Diesel Engine : 45,000 km (24,000 miles)Spark Plug ReplacementReplace spark plugs with same type. Type : BOSCH : F8DC4

BERU : 14F-8DU4Champion : C11YCC

Gap : 0.8 0.1 mmSpark Plug Wire ReplacementClean wires and inspect them for burns, cracks or otherdamage. Check the wire boot fit at the Distributor andat the spark plugs. Replace the wires as needed.Brake System ServiceCheck the disc brake pads or the drum brake linings.Check the pad and the lining thickness carefully.Tire and Wheel Inspection and RotationCheck the tires for abnormal wear or damage. Toequalize wear and obtain maximum tire life, rotate thetires. If irregular or premature wear exists, check thewheel alignment and check for damaged wheels. Whilethe tires and wheels are removed, inspect the brakes.

Tire Rotation (Left-hand Drive Type)

YAA0B010

GENERAL INFORMATION 0B-3

SSANGYONG Y200

WHILE OPERATING THE VEHICLEHorn OperationBlow the horn occasionally to make sure it works. Checkall the button locations.Brake System OperationBe alert for abnormal sounds, increased brake pedaltravel or repeated puling to one side when braking.Also, if the brake warning light goes on, or flashes,something may be wrong with part of the brake system.Exhaust System OperationBe alert to any changes in the sound of the system orthe smell of the fumes. These are signs that the systemmay be leaking or overheating. Have the system in-spected and repaired immediately.Tires, Wheels and Alignment OperationBe alert to any vibration of the steering wheel or theseats at normal highway speeds. This may mean awheel needs to be balanced. Also, a pull right or lefton a straight, level road may show the need for a tirepressure adjustment or a wheel alignment.Steering System OperationBe alert to changes in the steering action. An inspectionis needed when the steering wheel is hard to turn orhas too much free play, or is unusual sounds arenoticed when turning or parking.Headlamp AimTake note of the light pattern occasionally. Adjust theheadlights if the beams seem improperly aimed.

AT EACH FUEL FILLA fluid loss in any (except windshield washer) systemmay indicate a problem. Have the system inspectedand repaired immediately.Engine Oil LevelCheck the oil level and add oil if necessary. The besttime to check the engine oil level is when the oil iswarm.

1. After stopping the engine, wait a few minutes forthe oil to drain back to the oil pan.

2. Pull out the oil level indicator (dip stick).3. Wipe it clean, and push the oil level indicator back

down all the way.4. Pull out the oil level indicator and look at the oil

level on it.5. Add oil, if needed, to keep the oil level above the

lower mark. Avoid overfilling the engine, since thismay cause engine damage.

6. Push the indicator all the way back down into theengine after taking the reading.

OWNER INSPECTIONS AND SERVICESIf you check the oil level when the oil is cold, do notrun the engine first. The cold oil will not drain back tothe pan fast enough to give a true oil level reading.Engine Coolant Level and ConditionCheck the coolant level in the coolant reservoir tankand add coolant if necessary. Inspect the coolant.Replace dirty or rusty coolant.Windshield Washer Fluid LevelCheck the washer fluid level in the reservoir. Add fluidif necessary.

AT LEAST TWICE A MONTHTire And Wheel Inspection and PressureCheckCheck the tire for abnormal wear or damage. Also checkfor damaged wheels. Check the tire pressure whenthe tires are cold (check the spare also, unless it is astow-away).Maintain the recommended pressures. Refer to Tireand Wheel is in section 0B.

AT LEAST MONTHLYLamp OperationCheck the operation of the license plate lamp, the head-lamps (including the high beams), the parking lamps,the fog lamps, the taillamp, the brake lamps, the turnsignals, the backup lamps and the hazard warningflasher.Fluid Leak CheckPeriodically inspect the surface beneath the vehiclefor water, oil, fuel or other fluids, after the vehicle hasbeen parked for a while. Water dripping from the airconditioning system after use is normal. If you noticefuel leaks or fumes, find the cause and correct it atonce.

AT LEAST TWICE A YEARPower Steering System Reservoir LevelCheck the power steering fluid level. Keep the powersteering fluid at the proper level. Refer to Section 6A,Power Steering System.Brake Master Cylinder Reservoir LevelCheck the fluid and keep it at the proper level. A lowfluid level can indicate worn disc brake pads whichmay need to be serviced. Check the breather hole inthe reservoir cover to be free from dirt and check foran open pas-sage.Weather-Strip LubricationApply a thin film silicone grease using a clean cloth.

SSANGYONG Y200

0B-4 GENERAL INFORMATION

EACH TIME THE OIL IS CHANGEDBrake System InspectionThis inspection should be done when the wheels areremoved for rotation. Inspect the lines and the hosesfor proper hookup, binding, leaks, cracks, chafing, etc.Inspect the disc brake pads for wear. Inspect therotors for surface condition. Inspect other brake parts,the parking brake, etc., at the same time. Inspect thebrakes more often if habit or conditions result infrequent braking.Steering, Suspension and Front Drive AxleBoot And Seal InspectionInspect the front and rear suspension and the steeringsystem for damaged, loose or missing parts, signs ofwear or lack of lubrication. Inspect the power steeringline and the hoses for proper hookup, binding, leaks,cracks, chafing, etc. Clean and inspect the drive axleboot and seals for damage, tears or leakage. Replacethe seals if necessary.Exhaust System InspectionInspect the complete system (including the catalyticconverter if equipped). Inspect the body near theexhaust system. Look for broken, damaged, missing,or out-of-position parts as well as open seams, holes,loose connections, or other conditions which couldcause heat buildup in the floor pan or could let exhaustfumes seep into the trunk or passenger compartment.Throttle Linkage InspectionInspect the throttle linkage for interference or binding,damaged, or missing parts. Lubricate all linkage jointsand throttle cable joints, the intermediate throttle shaftbearing, the return spring at throttle valve assembly,and the accelerator pedal sliding face with suitablegrease. Check the throttle cable for free movements.Engine Drive BeltsInspect all belts for cracks, fraying, wear and propertension. Adjust or replace the belts as needed.Hood Latch OperationWhen opening the hood, note the operation of thesecondary latch. It should keep the hood from openingall the way when the primary latch is released. Thehood must close firmly.

AT LEAST ANNUALLYLap and Shoulder Belts Condition andOperationInspect the belt system including: the webbing, thebuckles, the latch plates, the retractor, the guide loopsand the anchors.Movable Head Restraint OperationOn vehicles with movable head restraints, the restraintsmust stay in the desired position.Spare Tire and Jack StorageBe alert to rattles in the rear of the vehicle. The sparetire, all the jacking equipment, and the tools must besecurely stowed at all times. Oil the jack ratchet or thescrew mechanism after each use.Key Lock ServiceLubricate the key lock cylinder.Body Lubrication ServiceLubricate all the body door hinges including the hood,the fuel door, the rear compartment hinges and thelatches, the glove box and the console doors, and anyfolding seat hardware.Underbody FlushingFlushing the underbody will remove any corrosivematerials used for ice and snow removal and dustcontrol. At least every spring clean the underbody.First, loosen the sediment packed in closed areas ofthe vehicle. Then flush the underbody with plain water.Engine Cooling SystemInspect the coolant and freeze protection fluid. If thefluid is dirty or rusty, drain, flush and refill the enginecooling system with new coolant. Keep the coolant atthe proper mixture in order to ensure proper freezeprotection, corrosion protection and engine operatingtemperature. Inspect the hoses. Replace the cracked,swollen, or deteriorated hoses. Tighten the clamps.Clean the outside of the radiator and the air conditioningcondenser. Wash the filler cap and the neck. Pressuretest the cooling system and the cap in order to helpen-sure proper operation.

GENERAL INFORMATION 0B-5

SSANGYONG Y200

STANDARD BOLTS SPECIFICATIONS

0.9 Nm(8 lb-in)2.0 Nm(18 lb-in)4.0 Nm(36 lb-in)6.7 Nm(60 lb-in)15.7 Nm(12 lb-in)32.3 Nm(24 lb-in)30.4 Nm(22 lb-in)56.8 Nm(42 lb-in)53.9 Nm(40 lb-in)89.2 Nm(66 lb-in)

107.8 Nm(80 lb-in)

196.0 Nm(145 lb-in)274.4 Nm(203 lb-in)372.4 Nm(276 lb-in)480.2 Nm(355 lb-in)460.6 Nm(341 lb-in)

1.3 Nm(12 lb-in)3.0 Nm(27 lb-in)5.6 Nm(50 lb-in)9.7 Nm(87 lb-in)22.5 Nm(17 lb-in)46.0 Nm(34 lb-in)44.1 Nm(33 lb-in)82.3 Nm(61 lb-in)77.4 Nm(57 lb-in)

127.4 Nm(94 lb-in)

196.0 Nm(145 lb-in)284.2 Nm(210 lb-in)392.0 Nm(290 lb-in)529.2 Nm(392 lb-in)686.0 Nm(508 lb-in)666.4 Nm(493 lb-in)

0.7 Nm(6.3 lb-in)1.6 Nm(14 lb-in)3.1 Nm(28 lb-in)5.4 Nm(49 lb-in)12.7 Nm(9 lb-in)

25.5 Nm(19 lb-in)24.5 Nm(18 lb-in)45.0 Nm(33 lb-in)43.1 Nm(32 lb-in)71.6 Nm(53 lb-in)

107.8 Nm(80 lb-in)

156.8 Nm(116 lb-in)215.6 Nm(160 lb-in)294.0 Nm(218 lb-in)382.2 Nm(283 lb-in)372.4 Nm(276 lb-in)

1.2 Nm(11 lb-in)2.6 Nm(23 lb-in)5.2 Nm(47 lb-in)9.0 Nm(81 lb-in)20.6 Nm

(15.2 lb-in)42.1 Nm(31 lb-in)41.2 Nm(30 lb-in)75.5 Nm(56 lb-in)71.5 Nm(53 lb-in)

117.6 Nm(87 lb-in)

186.2 Nm(138 lb-in)264.6 Nm(196 lb-in)362.6 Nm(268 lb-in)490.0 Nm(362 lb-in)637.0 Nm(471 lb-in)617.4 Nm(457 lb-in)

*Diameter X pitch in millimeters

Bolt*Torque (Nm / Ib-in)

Standard Limit4T 7T 9T 4T 7T 9T

M3 0.5

M4 0.7

M5 0.8

M6 1.0

M8 1.25

M10 1.25

M10 1.5

M12 1.25

M12 1.75

M14 1.5

M16 1.5

M18 1.5

M20 1.5

M22 0.5

M24 1.5

M24 2.0

0.5 Nm(4.5 lb-in)1.2 Nm(11 lb-in)2.4 Nm(22 lb-in)4.0 Nm(36 lb-in)8.6 Nm(77 lb-in)18.6 Nm(14 lb-in)18.6 Nm(14 lb-in)34.3 Nm(25lb-in)

32.3 Nm(24 lb-in)54.0 Nm(40 lb-in)81.3 Nm(60 lb-in)

117.6 Nm(87 lb-in)

166.6Nm(123 lb-in)225.4Nm(167 lb-in)284.2 Nm(210 lb-in)274.4 Nm(203 lb-in)

17 Nm(15 lb-in)4.0 Nm(36 lb-in)7.6 Nm(68 lb-in)12.7 Nm(114 lb-in)30.4 Nm(22 lb-in)60.8 Nm(31 lb-in)58.8 Nm(44 lb-in)

107.8 Nm(80 lb-in)98.0 Nm(73 lb-in)

166.6 Nm(123 lb-in)264.6 Nm(196 lb-in)372.4 Nm(276 lb-in)519.4 Nm(384 lb-in)705.6 Nm(522 lb-in)921.2 Nm(682 lb-in)891.8 Nm(660 lb-in)

YAA0B020

SSANGYONG Y200

0B-6 GENERAL INFORMATION

BASIC SPECIFICATIONDIMENSION

YAA0B030* ( ): Gasoline engine equipped vehicle

GENERAL INFORMATION 0B-7

SSANGYONG Y200

SPECIFICATIONS

SystemsGeneral

Engine

Manualtransmission

Automatictransmission

ItemsOverall length (mm)Overall width (mm)Overall height (mm)

Gross vehicle weight (kg)

Curb weight (kg)

Min. turning radius (m)Ground clearance (mm)

FuelFuel tank capacity

ModelNo. of cyl./Compression ratio

Total displacementCamshaft arrangement

Max. powerMax. torque

Injection timingIdle speed

Cooling systemCoolant capacity

LubricationMax. oil capacity

Turbo charger and cooling typeType

ModelType

Diesel4,2701,8701,760

AT : 2405,MT : 2365AT : 1950,MT : 1910

5.6200

Diesel80 L

OM662LA5 / 22 : 12,874 ccSOHC

120 ps / 4,000 rpm25.5 kg.m / 2,400 rpm

BTDC 18 1.0770 50 rpm

Water-cooled/forced circulation10.5 L ~ 11 L

Gear pump, forced circulation8.9 L

Turbo charger, air-cooledRemote control,

floor change type3.9692.3411.4571.0000.8513.705

ElectronicFloor change type

2.7421.5081.0000.7082.429

Gasoline G32D (G23D)4,745

1,780

2415

-

Gasoline

M162 (M161)6 / 10 : 13,199 ccDOHC

220 ps / 6,000 rpm31.9 kg.m / 3,000 rpm

BTDC 8770 50 rpm

11.3 L ~ 11.5 L

9.8 L-

1st

2nd

3rd

4th

5th

Rev.

1st

2nd

3rd

4th

Rev.

Gear ratio

Gear ratio

SSANGYONG Y200

0B-8 GENERAL INFORMATION

SPECIFICATIONS (Contd)Systems

Transfercase

Clutch

Powersteering

Front axle

Rear axle

Brake

Suspension

AirconditionerElectrical

ItemsModelType

Type

Disc type

Type

Drive shaft typeAxle housing typeDrive shaft type

Axle housing typeMaster cylinder type

Booster type

Parking brakeFrontRear

RefrigerantCompressor type

Battery type/Capacity (V-AH)Starter capacity (V-kW)

Alternator capacity (V-A)

DieselPart-time

Planetary gear type1.000 : 12.483 : 1Hydraulic

[A/T: Torque converter]Dry single diaphragm type[A/T: 3 elements 1 stage 2

phases]Rack and pinion

36173240

Ball joint typeBuild-up type

Semi-floating typeBuild-up typeTandem type

Vacuum boosterDisc

Drum (Disc)Cable type (internal expansion)

Wishbone + Coil spring5-link + Coil spring

R134aVane type

MF / 12 - 9012 - 2.2

12 - 75 (12 - 90)

Gasoline G32D (G23D)Full-time (Part-Time)

Torque converter

3 elements 1 stage 2 phases

Disc (Drum)

MF / 112 - 7512 - 1.812 - 115

HighLow

InnerOuter

FrontRear

Gear ratio

Type

Steering angle

GENERAL INFORMATION 0B-9

SSANGYONG Y200

Approved by MBSheet 229.1 or 229.3Viscosity: See MB

Sheet 224.1Approved by MB

Sheet 229.1 or 229.3Viscosity: See MB

Sheet 224.1CASTROL

TQ95

(ATF DEXRON II or III)

(DOT 4)

ATF DEXRON II, III, ATF S-2,S-3, S-4, TOTAL FLUID ATX

ATF DEXRON II,III, ATF S-2,S-3, S-4, TOTAL FLUID ATX

DOT4

API GL-5 orSAE 80W/90API GL-5 orSAE 80W/90

(ATF DEXRON II)

Engine Oil

Automatic TransmissionFluid*

Manual Transmission Fluid

Clutch Fluid(For Manual Transmission)Transfer CaseFluid

Brake Fluid

Front and RearAxle Fluid

Power Steering FluidCoolant

Air Cleaner

Fuel filter

RECOMMENDED FLUIDS AND LUBRICANTS

Usage Specification Service interval Capacity (L)Initial change: 1,000 km, Changeevery 10,000 km or 12 months(But, every 5,000 km or 6 monthsunder severe conditions)Initial change: max. 1,000 km,Change every 15,000 km or 12 months(But, every 7,500 km or 6 monthsunder severe conditions)Inspect every 30,000 km or 12 months(But, change every 60,000 kmunder severe conditions)Initially change at 12,000 km, andInspect every 50,000 kmInspect frequently, Change every40,000 km or 2 yearsInspect every 10,000 ~ 15,000 kmChange every 60,000 kmInspect every 10,000 ~ 15,000 kmChange every 60,000 kmChange every 40,000 km or 2 years(Inspect frequently)Inspect frequentlyChange every 38,000 kmInspect frequentlyChange every 38,000 kmCheck and replenish as necessary.

6.0 ~ 8.0

7.0 ~ 9.0

5.5 ~ 7.5

Approx. 9.5 L

Approx. 3.4 L

As required

1.2 L

1.4 L

As required

1.4 L

1.9 L

Approx. 1.1 L10.5~11.0 L10.0~10.5 L11.0~11.5 L

D29ST

G32D

G23D

Part-time

Full-time

Front Axle

Rear Axle

D29STG23DG32DDiesel

GasolineDiesel

Gasoline

Change every 3 years. And, inspect and replenish as necessary.

Clean every 10,000 km, Replace every 30,000 kmClean every 15,000 km, Replace every 60,000 kmReplace every 45,000 kmReplace every 60,000 km

SSANGYONG Y200

0B-10 GENERAL INFORMATION

VEHICLE IDENTIFICATION NUMBER SYSTEM

* K P T G 0 B 1 9 S 1 P 000000

12~17. Production Serial Number: 000001- 999999

11. Plant CodeP : PyongTaek Plant

10. Model Year2 : 20023 : 2003

9. Check DigitS : All area except North America

8. Engine Type6 : 2295cc, In-line 4Cylinder, Gasoline (E23)9 : 3199cc, In-line 6Cylinder, Gasoline (E32)D: 2874cc, In-line 5Cylinder, Diesel (662LA)

7. Restraint System1 : 3-Point Seat Belts, 2 : 2-Point Seat Belts

6. Trim LevelA : Standard, B : Deluxe, C: Super Deluxe

5. Body Type0 : 5-Door1 : 4-Door2 : 3-Door

4. Line ModelsG: Rexton (LHD)H: Rexton (RHD)

3. Vehicle TypeT : Passengr Cars, A : Truck

2. Maker Identification : P1. Nation : K*. Symbol according to No.

YAA0B040

VEHICLE IDENTIFICATIONNUMBER (VIN)Vehicle Identification Number (VIN) is on the right frontaxle upper frame.

GENERAL INFORMATION 0B-11

SSANGYONG Y200

YAA0B050

YAA0B060

YAA0B070

MANUFACTURERS PLATE

1 Type Approval No.2 Vehicle Identification No.

Manufacturers Plate LocationGasoline Engine

Diesel Engine

SSANGYONG Y200

0B-12 GENERAL INFORMATION

ENGINE NUMBERDiesel Engine

YAA0B080

The engine number is stamped on the cylinder blockin front of injection pump.

662 920 1 0 012345

Serial Number

0 : Manual T/M1 : Hydr - Auto Coupling2 : Automatic T/M

910 :Non-Intercooler Engine920 :Intercooler Engine

661 : 2299cc662 : 2874cc

0 : Common1 : Left - Hand Drive2 : Right - Hand Drive

5 : REXTON

YAA0B090

GENERAL INFORMATION 0B-13

SSANGYONG Y200

Gasolind Engine (3.2L DOHC)

YAA0B100

The engine number is stamped on the lower rearside of the alternator.

162 990 1 0 012345

Serial Number

0 : Manual T/M1 : Hydr - Auto Coupling2 : Automatic T/M

99 : 3.2L97 : 2.3L

ENGINE TYPE

0 : Common1 : Left - Hand Drive2 : Right - Hand Drive

5 : REXTON

YAA0B120

Gasolind Engine (2.3L DOHC)

YAA0B110

The engine number is stamped on the upper rearleft-hand side of the cylinder block.

SSANGYONG Y200

0B-14 GENERAL INFORMATION

VEHICLE LIFTING PROCEDURESTo raise the vehicle, place the lifting equipment onlyat the points indicated. Failure to use these precisepositions may result in permanent vehicle bodydeformation.Many dealer service facilities and service stations areequipped with automative hoists that bear upon someparts of the frame in order to lift the vehicle. If anyother hoist method is used, take special care to avoiddamaging the fuel tank, the filter neck, the exhaustsystem, or the underbody.

Using Floor Jack

YAA0B130

Front Side

YAA0B140

Rear Side

YAA0B150

Using Jack

YAA0B160

Rearward of Front Tire Forward of Rear Tire