SOLART R U E D E E P - C Y C L E S I G N A T U R E

D A T A S H E E T

ELECTRICAL SPECIFICATIONS

Voltage Capacity A Amp-Hours (Ah) Energy (kWh)

12V10-Hr 20-Hr 48-Hr 72-Hr 100-Hr 100-Hr

211 229 237 247 255 3.06

PRODUCT + PHYSICAL SPECIFICATIONS

Model Terminal Type D Dimensions B Inches (mm) Weight E Lbs. (kg) HydroLink or SPWK Handles

SSIG 12 255 6Length Width Height C

123 (56) SPWK Braided Rope14.97 (380) 6.91 (176) 14.67 (373)

CHARGING INSTRUCTIONS

Charger Voltage Settings (at 77°F/25°C)

System Voltage 12V 24V 48V

Maximum Charge Current (% of C20 Rate)* 13%

Maximum Absorption Phase Time (hours) 4

Absorption Voltage ** 14.70 29.40 58.80

Float Voltage 13.50 27.00 54.00

Equalization Voltage 16.20 32.40 64.80

Do not install or charge batteries in a sealed or non-ventilated compartment. Constant under or overcharging will damage the battery and shorten its life as with any battery.*If charging time is limited contact Trojan Technical Support for assistance.**In cases where controller has a bulk voltage setting, use absorption voltage setting above.

MODEL SSIG 12 255

VOLTAGE 12V

CAPACITY 255Ah @ 100Hr

MATERIAL Polypropylene

DIMENSIONS Inches (mm)

BATTERY Deep-Cycle Flooded/Lead Acid Battery

COLOR Maroon

WATERING Single-Point Watering Kit (Optional)

Designed in compliance with applicable BCI, DIN, BS and IEC standards. Tested in

compliance to BCI and IEC standards.

Polyon™ Case

CHARGING TEMPERATURE COMPENSATION

Add Subtract

0.005 volt per cell for every 1°C below 25°C0.0028 volt per cell for every 1°F below 77°F

0.005 volt per cell for every 1°C above 25°C 0.0028 volt per cell for every 1°F above 77°F

OPERATIONAL DATA

Operating Temperature Self Discharge

-4°F to 113°F (-20°C to +45°C). At temperatures below 32°F (0°C) maintain a state of charge greater than 60%.

5 – 15% per month depending on storagetemperature conditions.

Percentage Charge Specific Gravity Cell 12-Volt

100 1.277 2.122 12.73

90 1.258 2.103 12.62

80 1.238 2.083 12.50

70 1.217 2.062 12.37

60 1.195 2.040 12.24

50 1.172 2.017 12.10

40 1.148 1.993 11.96

30 1.124 1.969 11.81

20 1.098 1.943 11.66

10 1.073 1.918 11.51

STATE OF CHARGE MEASURE OF OPEN-CIRCUIT VOLTAGE

DOD VS CYCLE LIFE IN A STATIONARY APPLICATION

20% 30%

Depth-of-Discharge

Num

ber o

f Cyc

les

40% 50% 60% 70% 80%0

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

5500

20%0% 40% 60% 80% 100% 120%

0

20

-20

-40

40

60

80

100

120

140

0

-20

-10

-30

-40

10

20

30

40

50

60

Tem

pera

ture

(C)

Open

Circu

it Volt

age P

er Ce

ll

Stat

e of C

harg

e %

Storage Time in Weeks

Tem

pera

ture

(F)

Percent of Available Capacity

PERCENT CAPACITY VS. TEMPERATURE

2.12

2.10

2.04

2.08

2.06

2.02

1.99

1.97

1.92

1.94

0 2 4 6 8 10 12 14 16 18 20

100

80

90

70

60

50

40

30

20

10

Recharge Threshold @ 70% SOC

42°F (6°C)

75°F (24°C)

85°F (29°C)

Self Discharge vs. TimeSELF DISCHARGE VS. TIME*

*PERIODIC CHARGE

FREQUENCY

Provide a periodic freshening charge to maintain a SOC greater than the threshold of 70%.

TERMINAL CONFIGURATIONSD

6 DT Automotive Post & Stud Terminal

Terminal Height Inches (mm) 0.79 (20)

Torque Values: in-lb (Nm) Stud: 95 –105 (11 – 12) / AP: 50 – 70 (6 – 8)

Bolt Size 5/16" - 18

800.423.6569 / +1.562.236.3000 / trojanbattery.com© 2017 Trojan Battery Company, LLC. All rights reserved. Trojan Battery Company is not liable for damages that may result from any information provided in or omitted from this publication, under any circumstances. Trojan Battery Company reserves the right to make adjustments to this publication at any time, without notice or obligation.

SSIG_12_255_DS_083017

DIMENSIONS INCHES (MM) - shown with DT

A. The amount of amp-hours (Ah) a battery can deliver when discharged at a constant rate at 86°F (30°C) and maintain a voltage above 1.75 V/cell. Capacities are based on peak performance.

B. Dimensions may vary depending on type of handle or terminal. Batteries should be mounted with 0.5 inches (12.7 mm) spacing minimum.

C. Height taken from bottom of the battery to the highest point on the battery. Heights may vary depending on type of terminal. D. Terminal images are representative only.E. Weight may vary.

EXPECTED LIFE VS. TEMPERATURE

Chemical reactions internal to the battery are driven by voltage and temperature. The higher the battery temperature, the faster chemical reactions will occur. While higher temperatures can provide improved discharge performance the increased rate of chemical reactions will result in a corresponding loss of battery life. As a rule of thumb, for every 10°C increase in temperature the reaction rate doubles. Thus, a month of operation at 35°C is equivalent in battery life to two months at 25°C. Heat is an enemy of all lead acid batteries, FLA, AGM and gel alike and even small increases in temperature will have a major influence on battery life.

12380 CLARK ST. SANTA FE SPRINGS, CA 906705194 MINOLA DR. LITHONIA, GA 30038

SCALEDWN BY

DATE

TITLE

DWG NO

APPVD

REV

THIS DRAWING AND DATA EMBODY PROPRIETARY INFORMATION WHICH IS THE CONFIDENTIAL PROPERTY OF TROJAN BATTERY COMPANY WHICH SHALL NOT BE COPIED, REPRODUCED DISCLOSED TO OTHERS OR USED IN WHOLE OR PART FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF TROJAN BATTERY CO. THIS DRAWING IS LOANED IN CONFIDENCE WITH THE UNDERSTANDING THAT IT SHALL BE RETURNED ON DEMAND

CHK

UNLESS OTHERWISESPECIFICED

TOLERANCES ARE:

X.X ± 0.02"X.XX ± 0.01"X.XXX ± 0.005"ANGLES = ± 0 ° 30'

CSIZE=DWG SCALE

NOTES: UNLESS OTHERWISE SPECIFIED

A

B

C

D

E

F

G

H

B

C

D

E

F

G

H

1234567

7 6 5 4 3

3.74

1.71

14.67(373)

HEIGHT

14.97 (380)LENGTH

13.81(351)

6.91 (176)WIDTH

DATEREV DESCRIPTION ZONE8/11/10AINITIAL RELEASE; ECO2720

1. DIMENSIONS ARE NOMINAL

A7/22/10 720459BP DP CS

J185 (H-AC AND P-AC)BATTERY ASSEMBLY

5/16"-18STAINLESS STEEL

0.350SCALE

UNCONTROLLED COPY WHEN DOWNLOADED or PRINTED-Check MASTER DOCUMENT LOG to verify that this document/drawing is current prior to use

12380 CLARK ST. SANTA FE SPRINGS, CA 906705194 MINOLA DR. LITHONIA, GA 30038

SCALEDWN BY

DATE

TITLE

DWG NO

APPVD

REV

THIS DRAWING AND DATA EMBODY PROPRIETARY INFORMATION WHICH IS THE CONFIDENTIAL PROPERTY OF TROJAN BATTERY COMPANY WHICH SHALL NOT BE COPIED, REPRODUCED DISCLOSED TO OTHERS OR USED IN WHOLE OR PART FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF TROJAN BATTERY CO. THIS DRAWING IS LOANED IN CONFIDENCE WITH THE UNDERSTANDING THAT IT SHALL BE RETURNED ON DEMAND

CHK

UNLESS OTHERWISESPECIFICED

TOLERANCES ARE:

X.X ± 0.02"X.XX ± 0.01"X.XXX ± 0.005"ANGLES = ± 0 ° 30'

CSIZE=DWG SCALE

NOTES: UNLESS OTHERWISE SPECIFIED

A

B

C

D

E

F

G

H

B

C

D

E

F

G

H

1234567

7 6 5 4 3

3.74

1.71

14.67(373)

HEIGHT

14.97 (380)LENGTH

13.81(351)

6.91 (176)WIDTH

DATEREV DESCRIPTION ZONE8/11/10AINITIAL RELEASE; ECO2720

1. DIMENSIONS ARE NOMINAL

A7/22/10 720459BP DP CS

J185 (H-AC AND P-AC)BATTERY ASSEMBLY

5/16"-18STAINLESS STEEL

0.350SCALE

UNCONTROLLED COPY WHEN DOWNLOADED or PRINTED-Check MASTER DOCUMENT LOG to verify that this document/drawing is current prior to use

12380 CLARK ST. SANTA FE SPRINGS, CA 906705194 MINOLA DR. LITHONIA, GA 30038

SCALEDWN BY

DATE

TITLE

DWG NO

APPVD

REV

THIS DRAWING AND DATA EMBODY PROPRIETARY INFORMATION WHICH IS THE CONFIDENTIAL PROPERTY OF TROJAN BATTERY COMPANY WHICH SHALL NOT BE COPIED, REPRODUCED DISCLOSED TO OTHERS OR USED IN WHOLE OR PART FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF TROJAN BATTERY CO. THIS DRAWING IS LOANED IN CONFIDENCE WITH THE UNDERSTANDING THAT IT SHALL BE RETURNED ON DEMAND

CHK

UNLESS OTHERWISESPECIFICED

TOLERANCES ARE:

X.X ± 0.02"X.XX ± 0.01"X.XXX ± 0.005"ANGLES = ± 0 ° 30'

CSIZE=DWG SCALE

NOTES: UNLESS OTHERWISE SPECIFIED

A

B

C

D

E

F

G

H

B

C

D

E

F

G

H

1234567

7 6 5 4 3

3.74

1.71

14.67(373)

HEIGHT

14.97 (380)LENGTH

13.81(351)

6.91 (176)WIDTH

DATEREV DESCRIPTION ZONE8/11/10AINITIAL RELEASE; ECO2720

1. DIMENSIONS ARE NOMINAL

A7/22/10 720459BP DP CS

J185 (H-AC AND P-AC)BATTERY ASSEMBLY

5/16"-18STAINLESS STEEL

0.350SCALE

UNCONTROLLED COPY WHEN DOWNLOADED or PRINTED-Check MASTER DOCUMENT LOG to verify that this document/drawing is current prior to use