GN 950.6-F Spoked handwheels with fixed handle

Elesa-Gantergriff Main dimensions Mounting hole Handle Spokes no. Weight

Code Description d1 d3 ≈ b l2 ≈ d2 H9 l1 l3 Ø r d4 g

GN.32052 GN 950.6-100-B10-F 100 25.5 14.5 33 10 17 48.5 16 36 M 6 3 480

GN.32057 GN 950.6-100-K10-F 100 25.5 14.5 33 10 17 48.5 16 36 M 6 3 470

GN.32062 GN 950.6-125-B12-F 125 27 15.8 35.5 12 18 62 20 47 M 8 3 770

GN.32067 GN 950.6-125-K12-F 125 27 15.8 35.5 12 18 62 20 47 M 8 3 760

GN.32072 GN 950.6-140-B14-F 140 29 17 38.5 14 19 62 20 52 M 8 3 940

GN.32077 GN 950.6-140-K14-F 140 29 17 38.5 14 19 62 20 52 M 8 3 930

GN.32082 GN 950.6-160-B14-F 160 31 17.5 39.5 14 20 77 25 62 M 10 3 1320

GN.32087 GN 950.6-160-K14-F 160 31 17.5 39.5 14 20 77 25 62 M 10 3 1310

GN.32092 GN 950.6-200-B18-F 200 37 20 44.5 18 24 77 25 80 M 10 3 2060

GN.32097 GN 950.6-200-K18-F 200 37 20 44.5 18 24 77 25 80 M 10 3 2000

Material Cast AISI 316L stainless steel, turned and polished rim, sandblasted matte surface.

Fixed handle Cast AISI 316L stainless steel,.

Standard executions - GN 950.6-B: H9 reamed hole. - GN 950.6-K: H9 reamed hole and keyway in compliance with DIN 6885/1 P9 tolerance.

Special executions on request Handwheels with square mounting hole (GN 950.6-V).

ELESA-GANTER models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

VCM-SST Lobe knobs

ELESA Original design

Elesa Standards Main dimensions Mounting hole Weight

Code Description D L d1 l2 dH7 d h g

169541 VCM-SST-40-8 40 24 14 12 8 - 15 36

169542 VCM-SST-40-M8 40 24 14 12 - M8 15 37

169546 VCM-SST-50-10 50 31 18 17.5 10 - 18 63

169547 VCM-SST-50-M10 50 31 18 17.5 - M10 18 65

169551 VCM-SST-60-12 60 39 20 21 12 - 22 105

169552 VCM-SST-60-M12 60 39 20 21 - M12 22 107

Elesa Standards Main dimensions Threaded pin Weight

Code Description D L d1 l2 d l g

169561 VCM-SST-40-p-M8x20 40 24 14 12 M8 20 50

169562 VCM-SST-40-p-M8x30 40 24 14 12 M8 30 55

169563 VCM-SST-40-p-M8x40 40 24 14 12 M8 40 56

169571 VCM-SST-50-p-M10x20 50 30 18 16.5 M10 20 95

169572 VCM-SST-50-p-M10x30 50 30 18 16.5 M10 30 97

169573 VCM-SST-50-p-M10x40 50 30 18 16.5 M10 40 100

169581 VCM-SST-60-p-M12x30 60 37.5 20 20 M12 30 155

169582 VCM-SST-60-p-M12x40 60 37.5 20 20 M12 40 162

169583 VCM-SST-60-p-M12x50 60 37.5 20 20 M12 50 169

Material AISI 304 stainless steel, sandblasted matte finish.

Standard executions -VCM-SST: butt-welded hub, H7 reamed blind hole or threaded blind hole. -VCM-SST-p: butt-welded hub, threaded pin.

ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

EWNM-SST Wing nuts

ELESA Original design

Ergostyle Main dimensions Mounting hole Weight

Code Description D L d1 l2 b l3 d h g

222002 EWNM-SST-40-M5 40 21 13.5 5.5 6.5 19 M5 12 31

222004 EWNM-SST-40-M6 40 21 13.5 5.5 6.5 19 M6 12 31

222012 EWNM-SST-48-M6 48 24 13.5 6 7 22 M6 15 41

222014 EWNM-SST-48-M8 48 24 13.5 6 7 22 M8 15 40

222022 EWNM-SST-55-M8 55 28 16 7 8 25 M8 18 62

222024 EWNM-SST-55-M10 55 28 16 7 8 25 M10 18 61

Ergostyle Main dimensions Mounting hole Weight

Code Description D L d1 l2 b l3 d h d2 H13 g

222001 EWNM-SST-40-FP-M5 40 21 13.5 5.5 6.5 19 M5 8 5.3 30

222003 EWNM-SST-40-FP-M6 40 21 13.5 5.5 6.5 19 M6 10 6.4 29

222011 EWNM-SST-48-FP-M6 48 24 13.5 6 7 22 M6 10 6.4 40

222013 EWNM-SST-48-FP-M8 48 24 13.5 6 7 22 M8 13 8.4 39

222021 EWNM-SST-55-FP-M8 55 28 16 7 8 25 M8 13 8.4 59

222023 EWNM-SST-55-FP-M10 55 28 16 7 8 25 M10 16 10.5 57

Ergostyle Main dimensions Threaded stud Weight

Code Description D L d1 l2 b l3 d l g

222101 EWNM.40-SST-pM5x16 40 21 13.5 5.5 6.5 19 M5 16 32

222103 EWNM.40-SST-pM5x20 40 21 13.5 5.5 6.5 19 M5 20 36

222105 EWNM.40-SST-pM5x25 40 21 13.5 5.5 6.5 19 M5 25 40

222111 EWNM.40-SST-pM6x16 40 21 13.5 5.5 6.5 19 M6 16 35

222113 EWNM.40-SST-pM6x20 40 21 13.5 5.5 6.5 19 M6 20 42

222115 EWNM.40-SST-pM6x25 40 21 13.5 5.5 6.5 19 M6 25 46

222131 EWNM.48-SST-pM6x16 48 24 13.5 6 7 22 M6 16 44

222133 EWNM.48-SST-pM6x20 48 24 13.5 6 7 22 M6 20 50

222135 EWNM.48-SST-pM6x25 48 24 13.5 6 7 22 M6 25 54

222141 EWNM.48-SST-pM8x16 48 24 13.5 6 7 22 M8 16 46

222143 EWNM.48-SST-pM8x20 48 24 13.5 6 7 22 M8 20 50

222145 EWNM.48-SST-pM8x25 48 24 13.5 6 7 22 M8 25 52

222161 EWNM.55-SST-pM8x20 55 28 16 7 8 25 M8 20 55

222163 EWNM.55-SST-pM8x25 55 28 16 7 8 25 M8 25 58

222165 EWNM.55-SST-pM8x30 55 28 16 7 8 25 M8 30 61

222171 EWNM.55-SST-pM10x20 55 28 16 7 8 25 M10 20 53

222173 EWNM.55-SST-pM10x25 55 28 16 7 8 25 M10 25 56

222175 EWNM.55-SST-pM10x30 55 28 16 7 8 25 M10 30 60

Material AISI 304 stainless steel, sandblasted matte finish.

Standard executions - EWNM-SST: threaded blind hole. - EWNM-SST-FP: threaded pass-through hole. - EWNM-SST-p: threaded pin.

Special executions on request Different threadings.

Features and applications These wing nuts allow high tightening torque values.

Ergonomy and design The slightly concave marks on the wings help to position the fingers in order to apply the maximum force when tightening.

ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

GN 300.5 Adjustable handles

Elesa-Gantergriff Main dimensions Mounting hole Weight

Code Description l1 d3 d4 h1 h2 h3 h4 d1 t min. g

GN.15641 GN 300.5-30-M3-IS 30 10 13 24.5 4 31 3.5 M3 7 -

GN.15642 GN 300.5-30-M4-IS 30 10 13 24.5 4 31 3.5 M4 9 -

GN.15643 GN 300.5-30-M5-IS 30 10 13 24.5 4 31 3.5 M5 9 -

GN.15644 GN 300.5-30-M6-IS 30 10 13 24.5 4 31 3.5 M6 9 -

GN.15699 GN 300.5-45-M4-IS 45 10 13 24.5 4 35 3.5 M4 9 42

GN.15700 GN 300.5-45-M5-IS 45 10 13 24.5 4 35 3.5 M5 9 40

GN.15701 GN 300.5-45-M6-IS 45 10 13 24.5 4 35 3.5 M6 9 39

GN.15710 GN 300.5-63-M6-IS 63 13.5 17.5 31 6.5 45 4 M6 11 90

GN.15711 GN 300.5-63-M8-IS 63 13.5 17.5 31 6.5 45 4 M8 11 88

GN.15720 GN 300.5-78-M8-IS 78 16 21 36 8 55 4 M8 14 147

GN.15721 GN 300.5-78-M10-IS 78 16 21 36 8 55 4 M10 14 143

GN.15725 GN 300.5-92-M10-IS 92 19 24 43 11 63 4 M10 17 240

GN.15726 GN 300.5-92-M12-IS 92 19 24 43 11 63 4 M12 17 220

Lever body Stainless steel, sandblasted matte finish.

Standard execution AISI 303 stainless steel clamping element with threaded hole and retaining screw. AISI 301 stainless steel return spring.

Special executions on request

- Clamping element with different threadings. - Adjustable handles with hexagonal head retaining screw (GN 300.5-AS).

Features and applications Particularly suitable when the lever turning angle is limited owing to lack of space.

Instructions of use For clamping, lift the lever to disengage the clamping device teeth and bring it back to start position. By releasing the lever, the return spring automatically engages the teeth. If the lever cannot make a 360° rotation, the clamping element can be easily screwed by means of the hexagon socket front head screw (after having disengaged the lever).

ELESA-GANTER models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

GN 565.5 Handles

Elesa-Gantergriff Main dimensions Mounting holes Weight

Code Description b l ±0.25 a h r d tmin. g

GN.27431 GN 565.5-20-112 20 112 13 49 13 M6 10 293

GN.27435 GN 565.5-20-128 20 128 13 51 13 M6 10 330

GN.27437 GN 565.5-20-160 20 160 13 51 13 M6 10 366

GN.27439 GN 565.5-20-200 20 200 13 51 13 M6 10 440

GN.27441 GN 565.5-20-250 20 250 13 51 13 M6 10 517

GN.27443 GN 565.5-20-300 20 300 13 51 13 M6 10 597

GN.27445 GN 565.5-20-350 20 350 13 51 13 M6 10 660

GN.27447 GN 565.5-20-400 20 400 13 51 13 M6 10 737

Material AISI 304 stainless steel. Oval cross section bar, sandblasted matte finish.

Standard execution Threaded blind holes.

ELESA-GANTER models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

CMM-SST Hinges

Elesa Standards Main dimensions Fitting Weight

Code Description L f H h1 h2 b1 d d3 d4 g

428501 CMM-SST-40-SH-5 40 25 9 5.5 5 14 4 5.5 10.5 41

428601 CMM-SST-50-SH-6 50 30 11.5 6.5 6 18 6 6.5 12.5 81

428701 CMM-SST-60-SH-8 60 36 15 8.5 8 21.5 8 8.5 16.5 172

Material AISI 316 stainless steel

Colour Natural, electropolished finish.

Rotation pin AISI 303 stainless steel.

Standard execution Pass-through holes for countersunk head screws.

Rotation angle (approximate value) Max 270° (-90° and +180° being 0° the condition where the two interconnected surfaces are on the same plane). Do not exceed the rotation angle limit so as not to prejudice the hinge mechanical performance.

ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

GN 617.1-NI Indexing plungers with rest position

Elesa-Gantergriff Main dimensions Spring pressure Weight

Code Description d1 -0.02/-0.04 d2 d3 e l1 ≈ l2 min. l3 l4 l5 min. Preload Max. load g

GN.35503 GN 617.1-5-A-NI 5 M10x1 21 13.8 51 5 17 5 15 6 15 20

GN.35513 GN 617.1-6-A-NI 6 M12x1.5 25 16.2 61 6 20 6 17 8 21 34

GN.35523 GN 617.1-8-A-NI 8 M16x1.5 31 21.9 75.5 7 26 8 23 9 26 79

GN.35533 GN 617.1-10-A-NI 10 M20x1.5 31 25.4 91 10 33 10 30 17 40 130

GN.35505 GN 617.1-5-AN-NI 5 29 M10x1 21 17 5 5 15 12 6 15 30

GN.35515 GN 617.1-6-AN-NI 6 35 M12x1.5 25 20 6 6 17 14 8 21 46

GN.35525 GN 617.1-8-AN-NI 8 42.5 M16x1.5 31 26 7 8 23 19 9 26 94

GN.35535 GN 617.1-10-AN-NI 10 48 M20x1.5 31 33 10 10 30 22 17 40 145

GN.35504 GN 617.1-5-AK-NI 5 M10x1 21 13.8 51 5 17 5 15 6 15 30

GN.35514 GN 617.1-6-AK-NI 6 M12x1.5 25 16.2 61 6 20 6 17 8 21 48

GN.35524 GN 617.1-8-AK-NI 8 M16x1.5 31 21.9 75.5 7 26 8 23 9 26 99

GN.35534 GN 617.1-10-AK-NI 10 M20x1.5 31 25.4 91 10 33 10 30 17 40 163

GN.35506 GN 617.1-5-AKN-NI 5 29 M10x1 21 17 5 5 15 12 6 15 42

 

Elesa-Gantergriff Main dimensions Spring pressure Weight

Code Description d1 -0.02/-0.04 d2 d3 e l1 ≈ l2 min. l3 l4 l5 min. Preload Max. load g

GN.35516 GN 617.1-6-AKN-NI 6 35 M12x1.5 25 20 6 6 17 14 8 21 61

GN.35526 GN 617.1-8-AKN-NI 8 42.5 M16x1.5 31 26 7 8 23 19 9 26 105

GN.35536 GN 617.1-10-AKN-NI 10 48 M20x1.5 31 33 10 10 30 22 17 40 179

Threaded body AISI 303 stainless steel.

Plunger Nickel-plated AISI 303 stainless steel. Suggested tolerance for matching hole = H7 .

Locking nut Stainless steel.

Knob High-resilience polyamide based (PA) technopolymer, black colour, matte finish or AISI 303 stainless steel.

Standard executions - GN 617.1-A-NI: with technopolymer knob, without locking nut. - GN 617.1-AN-NI: with AISI 303 stainless steel knob, without locking nut. - GN 617.1-AK- NI: with technopolymer knob and locking nut. - GN 617.1-AKN-NI: with AISI 303 stainless steel knob and locking nut.

Accessories on request GN 609.5 AISI 303 stainless steel distance bushings are available for assembling the plunger on thin sheets.

ELESA-GANTER models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

HCX-SST Column level indicators stainless steel assembly screws

ELESA Original design

 

Elesa Standards Main dimensions Mounting holes Thermometer scale C # Weight

Code Description f d A B C L e m r d ' -0.2 f '±0.2 °C °F [Nm] g

11343 HCX.76-SST-M10 76 M10 22 16 27 107 40 18 15.5 10.5 76 - - 12 87

11348 HCX.76/T-SST-M10 76 M10 22 16 27 107 40 18 15.5 10.5 76 20÷100 68÷210 12 87

11353 HCX.127-SST-M12 127 M12 23 18 31 161 80 23 17 12.5 127 - - 12 138

11358 HCX.127/T-SST-M12 127 M12 23 18 31 161 80 23 17 12.5 127 0÷100 32÷210 12 138

11363 HCX.254-SST-M12 254 M12 21 18 35 291 203 26 18.5 12.5 254 - - 10 185

11368 HCX.254/T-SST-M12 254 M12 21 18 35 291 203 26 18.5 12.5 254 0÷100 32÷210 10 185

# Maximum tightening torque.

Material Transparent polyamide based (PA-T) technopolymer. High resistance to shocks, solvents, oils with additives, aliphatic and aromatic hydrocarbons, petrol, naphtha, phosphoric esters. Avoid contact with alcohol or detergents containing alcohol.

Screws, nuts and washers AISI 303 stainless steel screws, AISI 304 stainless steel nuts and washers.

Packing rings FKM type VITON®* O-Ring.

Contrast screen White lacquered aluminium. The housing, in the appropriate external rear slot, guarantees the best protection from direct contact with fluid, avoiding yellowing effect due to the prolonged action of the fluid at high temperatures. It can be removed before installation to fit marks and words (for example MAX-MIN) in the needed positions.

Standard executions - HCX-SST: without thermometer. - HCX/T-SST: with incorporated thermometer.

Assembly - By means of the supplied set screws and nuts. - By means of the supplied set screws, without nuts, by tapping the two holes in the reservoir walls, if they are thick enough. To ensure the best sealing of the O-rings it is recommended to apply the maximum torque on the nuts as reported in the table and a roughness of the gasket application surface Ra = 3 µm.

Maximum continuous working temperature 90°C (with oil).

Special executions on request UV resistant transparent technopolymer indicators.

Features and performances The body of the indicator, entirely in transparent material, is assembled using ultrasound welding to guarantee a perfect seal. Maximum fluid level visibility even from side positions. Level visibility and temperature reading magnified by lens effect.

Technical data In laboratory tests carried out with mineral oil type CB68 (according to ISO 3498) at 23°C for a limited period of time, the weld stood up as follows: - HCX.76-SST 18 bar - HCX.127-SST 18 bar - HCX.254-SST 12 bar If you need to use the indicator with other oils or fluids and under different pressure and temperature conditions, please contact ELESA Technical Department. In any case we suggest to verify the suitability of the product under the actual working conditions.

Other standard executions - HCX-AR for use with fluids containing alcohol. - HCX-BW-SST for use with hot water. * Registered trademark by DuPont Dow Elastomer.

ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.

RE.FF Injected polyurethan wheels

Static load Rolling Dynamic carryingElesa Standards Main dimensions Weight* resistance capacity

Code Description D d l3 l4 H B L s b1 l1 b2 l2 b3 R d1 d2 [N] [N] [N] g

451001 RE.FF-080­RBL 80 12 30 39 - - - - - - - - - - - - 2200 1200 1200 110

451006 RE.FF-100­RBL 100 12 30 44 - - - - - - - - - - - - 3000 1700 1700 150

451011 RE.FF-125­RBL 125 15 35 44 - - - - - - - - - - - - 3500 2300 2300 250

451016 RE.FF-150­RBL 150 20 45 59 - - - - - - - - - - - - 5000 2800 3500 470

451151 RE.FF-080­PBL 80 12 30 - 107 100 85 9 75 45 80 60 - - - - - 1200 1200 380

451156 RE.FF-100­PBL 100 12 30 - 128 100 85 9 75 45 80 60 - - - - - 1700 1700 430

451161 RE.FF-125­PBL 125 15 35 - 156 100 85 9 75 45 80 60 - - - - - 2300 2200 660

451166 RE.FF-150­PBL 150 20 45 - 194 140 114 11 105 73 105 85 - - - - - 2800 3000 1460

451051 RE.FF-080­SBL 80 12 30 - 107 100 85 9 75 45 80 60 39 - - - - 1200 1200 620

451056 RE.FF-100­SBL 100 12 30 - 128 100 85 9 75 45 80 60 35 - - - - 1700 1700 740

451061 RE.FF-125­SBL 125 15 35 - 156 100 85 9 75 45 80 60 37 - - - - 2300 2200 910

451066 RE.FF-150­SBL 150 20 45 - 194 140 110 11 105 73 105 87 56 - - - - 2800 3000 1830

451101 RE.FF-080­SBF 80 12 30 - 107 100 85 9 75 45 80 60 39 120 - - - 1200 1200 810

451106 RE.FF-100­SBF 100 12 30 - 128 100 85 9 75 45 80 60 35 120 - - - 1700 1700 890

451111 RE.FF-125­SBF 125 15 35 - 156 100 85 9 75 45 80 60 37 120 - - - 2300 2200 1050

451116 RE.FF-150­SBF 150 20 45 - 194 140 110 11 105 73 105 87 56 156 - - - 2800 3000 2110

 

Elesa Standards Main dimensions Static load * Rolling resistance Dynamic carrying capacity Weight

Code Description D d l3 l4 H B L s b1 l1 b2 l2 b3 R d1 d2 [N] [N] [N] g

451171 RE.FF-80-FBL 80 12 30 - 107 ­ - ­ - - - - 39 - 73 12 - 1200 1200 550

451173 RE.FF-100-FBL 100 12 30 - 128 ­ - ­ - - - - 35 - 73 12 - 1700 1700 670

451176 RE.FF-125-FBL 125 15 35 - 156 ­ - ­ - - - - 37 - 73 12 - 2300 2200 850

451179 RE.FF-150-FBL 150 20 45 - 188 ­ - ­ - - - - 56 - 102 20 - 2800 3000 1690

451181 RE.FF-80-FBF 80 12 30 - 107 ­ - ­ - - - - 39 120 73 12 - 1200 1200 730

451183 RE.FF-100-FBF 100 12 30 - 128 ­ - ­ - - - - 35 120 73 12 - 1700 1700 880

451186 RE.FF-125-FBF 125 15 35 - 156 ­ - ­ - - - - 37 120 73 12 - 2300 2200 1000

451189 RE.FF-150-FBF 150 20 45 - 188 ­ - ­ - - - - 56 156 102 20 - 2800 3000 1980

* The static load value is characteristic of the wheel only without motion

Elesa Standards Main dimensions Rolling resistance Dynamic carrying capacity Weight

Code Description D d l3 H B L s b1 l1 b2 l2 b3 R d1 d2 [N] [N] g

451301 RE.FF-080-PBL-SST 80 12 30 107 100 85 9 75 45 80 60 - - - - 1200 1200 350

451306 RE.FF-100-PBL-SST 100 12 30 128 100 85 9 75 45 80 60 - - - - 1700 1700 400

451311 RE.FF-125-PBL-SST 125 15 35 156 100 85 9 75 45 80 60 - - - - 2300 2200 640

451201 RE.FF-080-SBL-SST 80 12 30 107 100 85 9 75 45 80 60 39 - - - 1200 1200 610

451206 RE.FF-100-SBL-SST 100 12 30 128 100 85 9 75 45 80 60 35 - - - 1700 1700 650

451211 RE.FF-125-SBL-SST 125 15 35 156 100 85 9 75 45 80 60 37 - - - 2300 2200 810

451251 RE.FF-080-SBF-SST 80 12 30 107 100 85 9 75 45 80 60 39 120 - - 1200 1200 780

451256 RE.FF-100-SBF-SST 100 12 30 128 100 85 9 75 45 80 60 35 120 - - 1700 1700 830

451261 RE.FF-125-SBF-SST 125 15 35 156 100 85 9 75 45 80 60 37 120 - - 2300 2200 950

451351 RE.FF-080-FBL-SST 80 12 30 107 - - - - - - - 39 - 73 12 1200 1200 550

451353 RE.FF-100-FBL-SST 100 12 30 128 - - - - - - - 35 - 73 12 1700 1700 670

451356 RE.FF-125-FBL-SST 125 15 35 156 - - - - - - - 37 - 73 12 2300 2200 850

451361 RE.FF-080-FBF-SST 80 12 30 107 - - - - - - - 39 120 73 12 1200 1200 550

451363 RE.FF-100-FBF-SST 100 12 30 128 - - - - - - - 35 120 73 12 1700 1700 770

451366 RE.FF-125-FBF-SST 125 15 35 156 - - - - - - - 37 120 73 12 2300 2200 860

Covering Injected polyurethan, hardness 55 Shore D.

Wheel centre body Polyamide-based technopolymer (PA). Resistant to solvents, oils and other chemicals.

Bore Directly made into the centre.

Axle set Calibrated precision tube. The tube serves as a spacer, is tightened to the bracket with screw and nut to a un predetermined torque value. The wheel bore rotates onto the tube freely.

Standard executions - RBL: wheel only. - PBL: brakeless wheel and zinc-plated steel fixed plate bracket. - SBL: brakeless wheel and zinc-plated steel turning plate bracket. - SBF: wheel with brake and zinc-plated steel turning plate bracket. - FBL: brakeless wheel and zinc-plated steel turning plate bracket with central pass-through hole. - FBF: wheel with brake and zinc-plated steel turning plate bracket with central pass-through hole. - PBL-SST: brakeless wheel and stainless steel fixed plate bracket. - SBL-SST: brakeless wheel and stainless steel turning plate bracket. - SBF-SST: wheel with brake and stainless steel turning plate bracket. - FBL-SST: brakeless wheel and stainless steel turning plate bracket with central pass-through hole. - FBF-SST: wheel with brake and stainless steel turning plate bracket with central pass-through hole.

Fixed plate bracket Zinc-plated steel or stainless steel (SST version) plate, the bracket is designed to withstand loads up to 4000N. The bracket load capacity is greater than the dynamic carrying capacity of the wheel assembly plus the bracket (see table), this is a further safety feature.

Turning plate bracket Zinc-plated steel or stainless steel (SST version) plate, the bracket is designed to withstand loads up to 4000N. The bracket load capacity is greater than the dynamic carrying capacity of the wheel assembly plus the bracket (see table), this is a further safety feature. The presence of two ball turns and the direct contact between the plate and the ball race ring with built-in pin ensure excellent manoeuvrability

and very limited clearance (see fig. 1). Does not require maintenance. It consists of: 1) fitting plate: electrolytically zinc-plated steel plate; 2) fork: electrolytically zinc-plated steel plate; 3) ball race ring: electrolytically zinc-plated steel plate; 4) central pin: incorporated in the plate, cold reflanged; 5) rotation system: dual grease-lubricated ring of ball; 6) dust seal: RAL 7015 dark grey technopolymer.

Front-actuated brake Total brake that locks the wheel and bracket rotation. The optimised dimensions and the retractible pedal ensure minimal space occupied and maximum actuation ease. In order to optimise the wheel lock in both directions of rotation, the spring is fitted with a dual braking tooth. Hardened carbon steel or stainless steel (SST version) spring.

Applications Excellent smoothness and elasticity features, good wear and tearing resistance.

Environmental conditions Suitable for use in environments with the presence of atmospheric agents, alcohols and glycols; weak organic and mineral acids, water and saturated vapour.

Rolling resistance - force / load applied The diagram shows the force to be applied to a wheel to keep it moving at the constant speed of 4 km/h, according to the applied load. The intersection point with a 50N value is the maximum transportable load with a manually actuated 4-wheel trolley; in fact, 200N = 50N x 4 wheels is the maximum force that may be supported by the operator according to the regulations in force regarding work safety.

Mechanical moving with towing devices For mechanical towing, please see the technical specifications to determine the capacity variation.

Temperature If operating temperatures in an application differ from the standard range of values, please see the technical specifications to determine the capacity variation.

ELESA models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.