Standard VCS 5081 159 - ePoptávka.cz · PDF fileStandard VCS 5081,159 Issue 1 Page 2...

Standard VCS 5081,159

Dept / Issued by 6857 Torbjörn Holmqvist Issue 1 Established 2005-06 UM Page 1(40)

Volvo Car Corporation

The English language version is the original and the reference in case of dispute.

Den engelska språkversionen är originalversion och skall åberopas i händelse av tvist.

ISO metric screw threads Metriska ISO-gängor Limits of sizes Gränsmått

Orientation Orientering There is no corresponding Swedish or international standard available but the corresponding way of listing the values can be found in DIN 13.

Standarden saknar motsvarighet i svensk och inter-nationell standard, men i DIN 13 finns motsvarande sätt att lista värdena.

This VCS standard is identical to the previously issued STD 5081,15 issue 5, which it replaces for Volvo Cars.

Denna VCS-standard är identisk med tidigare utgiven STD 5081,15, utgåva 5, och ersätter denna för Volvo Personvagnar.

Scope Omfattning This standard contains calculated limits of sizes for ISO metric screw threads with normal length of engagement.

Denna standard upptar framräknade gränsmått för metriska ISO-gängor med normal ingreppslängd.

The values have been calculated with the help of ISO 965/1-3.

Värdena är framräknade med hjälp av SS-ISO 965/1-3.

General Allmänt

For the minor diameter of external threads and for the major diameter of internal threads the table values refer to the position of the point on the profile where the requirement for a straight flank ceases.

För utvändig gängas innerdiameter och för invändig gängas ytterdiameter avser tabellvärdena läget för den punkt på profilen där kravet på rak flank upphör.


Issue 1 Page 2


Surface-coated threads Ytbelagda gängor The tolerance values apply to surface-coated threads before surface coating if nothing else has been indicated or agreed upon.

För ytbelagd gänga gäller toleransvärdena före ytbeläggning om inget annat angetts eller överens-kommits.

After being surface coated, the thread must not any-where - for external threads - exceed the basic profile (h position) or - for internal threads - be below the basic profile (H position).

Efter ytbeläggning får gängan inte i någon punkt - vid utvändig gänga - överskrida basprofilen (h-läget) eller - vid invändig gänga - underskrida basprofilen (H-läget).

Because of this fact, approval of surface-coated threads shall always be carried out using GO gauges for tolerance positions h and H respectively.

Godkännande av ytbelagda gängor skall därför alltid ske med hjälp av gå-tolkar för toleranslägena h respektive H.

The basic sizes for these gauges are given in the table. For external threads it is the max values for tolerance position h, and for internal threads it is the min values for tolerance position H.

Basmåtten för dessa tolkar ges i tabellen. För utvän-dig gänga är det maxvärdena för toleransläge h och för invändig gänga minvärdena för toleransläge H.

After removal of the surface coating, the thread must be within the tolerance limits that apply before surface coating. Threads with the tolerance 6g may, however, be within the tolerance area for 6e.

Efter avlösning av ytbeläggningsskiktet skall gängan ligga inom de toleransgränser som gäller före yt-beläggningen. Dock gäller att gängor med tolerans 6g får ligga inom det toleransområde som gäller för 6e.

Reference on drawing Hänvisning på ritning On drawings of M-threads, the following note shall be indicated in the drawing’s text space:

På ritning med M-gängor anges följande not i rit-ningens skrivfält:

THREAD TOLERANCES VCS 5081,159


Issue 1 Page 3


Limits of sizes for external threads Gränsmått för utvändiga gängor

Thread designation

Tol. Major diameter d Ytterdiameter d

Pitch diameter d2

Medeldiameter d2 Minor dia-meter d1

Gäng-beteckning

Max

Min

Max

Min

Innerdia-meter d1 Max

M3(x0,5) h 3,000 ----- 2,675 ----- 2,459 6g 2,980 2,874 2,655 2,580 2,439 6e 2,950 2,844 2,625 2,550 2,409 M3x0,35 h 3,000 ----- 2,773 ----- 2,621 6g 2,981 2,896 2,754 2,687 2,602 M3,5(x0,6) h 3,500 ----- 3,110 ----- 2,850 6g 3,479 3,354 3,089 3,004 2,829 6e 3,447 3,322 3,057 2,972 2,797 M3,5x0,35 h 3,500 ----- 3,273 ----- 3,121 M4(x0,7) h 4,000 ----- 3,545 ----- 3,242 6g 3,978 3,838 3,523 3,433 3,220 6e 3,944 3,804 3,489 3,399 3,186 js 4,030 3,875 3,575 3,515 3,171 M4x0,5 h 4,000 ----- 3,675 ----- 3,459 6g 3,980 3,874 3,655 3,580 3,439 6e 3,950 3,844 3,625 3,550 3,409 M4,5(x0,75) h 4,500 ----- 4,013 ----- 3,688 6g 4,478 4,338 3,991 3,901 3,666 6e 4,444 4,304 3,957 3,367 3,632 js 4,531 4,366 4,044 3,982 3,611 M4,5x0,5 h 4,500 ----- 4,175 ----- 3,959 M5(x0,8) h 5,000 ----- 4,480 ----- 4,134 6g 4,976 4,826 4,456 4,361 4,110 8g 4,976 4,740 4,456 4,306 4,110 6e 4,940 4,790 4,420 4,325 4,074 8e 4,940 4,704 4,420 4,270 4,074 js 5,033 4,863 4,513 4,447 4,052 M5x0,5 h 5,000 ----- 4,675 ----- 4,459 6g 4,980 4,874 4,655 4,580 4,439 6e 4,950 4,844 4,625 4,550 4,409 M5,5x0,5 h 5,500 ----- 5,175 ----- 4,959 M6(x1) h 6,000 ----- 5,350 ----- 4,917 6g 5,974 5,794 5,324 5,212 4,891 8g 5,974 5,694 5,324 5,144 4,891 6e 5,940 5,760 5,290 5,178 4,857 8e 5,940 5,660 5,290 5,110 4,857 js 6,037 5,830 5,387 5,313 4,810 M6x0,75 h 6,000 ----- 5,513 ----- 5,188 6g 5,978 5,838 5,491 5,391 5,166 6e 5,944 5,804 5,457 5,357 5,132


Issue 1 Page 4


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M7(x1) h 7,000 ----- 6,350 ----- 5,917 6g 6,974 6,794 6,324 6,212 5,891 8g 6,974 6,694 6,324 6,144 5,891 6e 6,940 6,760 6,290 6,178 5,857 8e 6,940 6,660 6,290 6,110 5,857 js 7,038 6,833 6,388 6,312 5,811 M7x0,75 h 7,000 ----- 6,513 ----- 6,188 M8(x1,25) h 8,000 ----- 7,188 ----- 6,647 6g 7,972 7,760 7,160 7,042 6,619 8g 7,972 7,637 7,160 6,970 6,619 6e 7,937 7,725 7,125 7,007 6,584 7e6e 7,937 7,725 7,125 6,975 6,584 8e 7,937 7,602 7,125 6,935 6,584 js 8,042 7,797 7,230 7,146 6,508 M8x1 h 8,000 ----- 7,350 ----- 6,917 6g 7,974 7,794 7,324 7,212 6,891 6e 7,940 7,760 7,290 7,178 6,857 M8x0,75 h 8,000 ----- 7,513 ----- 7,188 6g 7,978 7,838 7,491 7,391 7,166 6e 7,944 7,804 7,457 7,357 7,132 M9(x1,25) h 9,000 ----- 8,188 ----- 7,647 6g 8,972 8,760 8,160 8,160 7,619 8g 8,972 8,637 8,160 7,970 7,619 6e 8,937 8,725 8,125 8,007 7,584 8e 8,937 8,602 8,125 7,935 7,584 M9x1 h 9,000 ----- 8,350 ----- 7,917 M9x0,75 h 9,000 ----- 8,513 ----- 8,188 M10(x1,5) h 10,000 ----- 9,026 ----- 8,376 6g 9,968 9,732 8,994 8,862 8,344 8g 9,968 9,593 8,994 8,782 8,344 6e 9,933 9,697 8,959 8,827 8,309 8e 9,933 9,558 8,959 8,747 8,309 js 10,047 9,772 9,073 8,979 8,207 M10x1,25 h 10,000 ----- 9,188 ----- 8,647 6g 9,972 9,760 9,160 9,042 8,619 6e 9,937 9,725 9,125 9,007 8,584 M10x1 h 10,000 ----- 9,350 ----- 8,917 6g 9,974 9,794 9,324 9,212 8,891 6e 9,940 9,760 9,290 9,178 8,857 M10x0,75 h 10,000 ----- 9,513 ----- 9,188 6g 9,978 9,838 9,491 9,391 9,166 6e 9,944 9,804 9,457 9,357 9,132 M11(x1,5) h 11,000 ----- 10,026 ----- 9,376 6g 10,968 10,732 9,994 9,862 9,344 M11(x1,5) 8g 10,968 10,593 9,994 9,782 9,344 6e 10,933 10,697 9,959 9,827 9,309 8e 10,933 10,558 9,959 9,747 9,309 M11x1,25 h 11,000 ----- 10,188 ----- 9,647 6g 10,972 10,760 10,160 10,042 9,619 6e 10,937 10,725 10,125 10,007 9,584


Issue 1 Page 5


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M11x1 h 11,000 ----- 10,350 ----- 9,917 6g 10,974 10,794 10,324 10,212 9,891 6e 10,940 10,760 10,290 10,178 9,857 M11x0,75 h 11,000 ----- 10,513 ----- 10,188 M12(x1,75) h 12,000 ----- 10,863 ----- 10,106 6g 11,966 11,701 10,829 10,679 10,072 8g 11,966 11,541 10,829 10,593 10,072 6e 11,929 11,664 10,792 10,642 10,035 8e 11,929 11,504 10,792 10,556 10,035 js 12,051 11,741 10,914 10,812 9,904 M12x1,59 h 12,000 ----- 10,967 ----- 10,279 6g 11,968 11,725 10,935 10,795 10,247 M12x1,5 h 12,000 ----- 11,026 ----- 10,376 6g 11,968 11,732 10,994 10,854 10,344 6e 11,933 11,697 10,959 10,918 10,309 M12x1,25 h 12,000 ----- 11,188 ----- 10,647 6g 11,972 11,760 11,160 11,028 10,619 6e 11,937 11,725 11,125 10,993 10,584 M12x1 h 12,000 ----- 11,350 ----- 10,917 6g 11,974 11,794 11,324 11,206 10,891 6e 11,940 11,760 11,290 11,172 10,857 M12x0,75 h 12,000 ----- 11,513 ----- 11,188 6g 11,978 11,838 11,491 11,385 11,166 6e 11,944 11,804 11,457 11,351 11,132 M14(x2) h 14,000 ----- 12,701 ----- 11,835 6g 13,962 13,682 12,663 12,503 11,797 8g 13,962 13,512 12,663 12,413 11,797 6e 13,929 13,649 12,630 12,470 11,764 8e 13,929 13,479 12,630 12,380 11,764 js 14,055 13,715 12,756 12,646 11,601 M14x1,5 h 14,000 ----- 13,026 ----- 12,376 6g 13,968 13,732 12,994 12,854 12,344 6e 13,933 13,697 12,959 12,819 12,309 M14x1,25 h 14,000 ----- 13,188 ----- 12,647 6g 13,972 13,760 13,160 13,028 12,619 6e 13,937 13,725 13,125 12,993 12,584 M14x1 h 14,000 ----- 13,350 ----- 12,917 6g 13,974 13,794 13,324 13,206 12,891 M14x1 6e 13,940 13,760 13,290 13,172 12,857 M15x2 h 15,000 ----- 13,701 ----- 12,835 6g 14,962 14,682 13,663 13,503 12,797 6e 14,929 14,649 13,630 13,470 12,764 M15x1,5 h 15,000 ----- 14,026 ----- 13,376 M15x1 h 15,000 ----- 14,350 ----- 13,917 6g 14,974 14,794 14,324 14,206 13,891 6e 14,940 14,760 14,290 14,172 13,857 M16(x2) h 16,000 ----- 14,701 ----- 13,835 6g 15,962 15,682 14,663 14,503 13,797 8g 15,962 15,512 14,663 14,413 13,797


Issue 1 Page 6


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


6e 15,929 15,649 14,630 14,470 13,764 8e 15,929 15,479 14,630 14,380 13,764 js 16,057 15,717 14,758 14,644 13,603 M16x1,5 h 16,000 ----- 15,026 ----- 14,376 6g 15,968 15,732 14,994 14,854 14,344 6e 15,933 15,697 14,959 14,819 14,309 M16x1 h 16,000 ----- 15,350 ----- 14,917 6g 15,974 15,794 15,324 15,206 14,891 6e 15,940 15,760 15,290 15,172 14,857 M17x1,5 h 17,000 ----- 16,026 ----- 15,376 6g 16,968 16,732 15,994 15,854 15,344 6e 16,933 16,697 15,959 15,819 15,309 M17x1 h 17,000 ----- 16,350 ----- 15,917 6g 16,974 16,794 16,324 16,206 15,891 6e 16,940 16,760 16,290 16,172 15,857 M18(x2,5) h 18,000 ----- 16,376 ----- 15,294 6g 17,958 17,623 16,334 16,164 15,252 8g 17,958 17,428 16,334 16,069 15,252 6e 17,920 17,585 16,296 16,126 15,214 8e 17,920 17,390 16,296 16,031 15,214 js 18,063 17,663 16,439 16,313 14,996 M18x2 h 18,000 ----- 16,701 ----- 15,835 M18x1,5 h 18,000 ----- 17,026 ----- 16,376 6g 17,968 17,732 16,994 16,854 16,344 6e 17,933 17,697 16,959 16,819 16,309 M18x1 h 18,000 ----- 17,350 ----- 16,917 6g 17,974 17,794 17,324 17,206 16,891 6e 17,940 17,760 17,290 17,172 16,857 M20(x2,5) h 20,000 ----- 18,376 ----- 17,294 6g 19,958 19,623 18,334 18,164 17,252 8g 19,958 19,428 18,334 18,069 17,252 6e 19,920 19,585 18,296 18,126 17,214 8e 19,920 19,390 18,296 18,031 17,214 M20(x2,5) js 20,064 19,664 18,440 18,312 16,997 M20x2 h 20,000 ----- 18,701 ----- 17,835 6g 19,962 19,682 18,663 18,503 17,797 6e 19,929 19,649 18,630 18,470 17,764 M20x1,5 h 20,000 ----- 19,026 ----- 18,376 6g 19,968 19,732 18,994 18,854 18,344 6e 19,933 19,697 18,959 18,819 18,309 M20x1 h 20,000 ----- 19,350 ----- 18,917 6g 19,974 19,794 19,324 19,206 18,891 6e 19,940 19,760 19,290 19,172 18,857 M22(x2,5) h 22,000 ----- 20,376 ----- 19,294 6g 21,958 21,623 20,344 20,164 19,252 8g 21,958 21,428 20,344 20,069 19,252 6e 21,920 21,585 20,296 20,126 19,214 8e 21,920 21,390 20,296 20,031 19,214 js 22,065 21,665 20,441 20,311 18,998 M22x2 h 22,000 ----- 20,701 ----- 19,835


Issue 1 Page 7


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M22x1,5 h 22,000 ----- 21,026 ----- 20,376 6g 21,968 21,732 20,994 20,854 20,334 6e 21,933 21,697 20,959 20,819 20,309 M22x1 h 22,000 ----- 21,350 ----- 20,917 6g 21,974 21,794 21,324 21,206 20,891 6e 21,940 21,760 21,290 21,172 20,857 M24(x3) h 24,000 ----- 22,051 ----- 20,752 6g 23,952 23,577 22,003 21,803 20,704 8g 23,952 23,352 22,003 21,688 20,704 6e 23,915 23,540 21,966 21,766 20,667 8e 23,915 23,315 21,966 21,651 20,667 js 24,071 23,621 22,122 21,980 20,390 M24x2 h 24,000 ----- 22,701 ----- 21,835 6g 23,962 23,682 22,663 22,493 21,797 6e 23,929 23,649 22,630 22,460 21,764 M24x1,5 h 24,000 ----- 23,026 ----- 22,376 4h 24,000 23,850 23,026 22,931 22,376 6g 23,968 23,732 22,994 22,844 22,344 6e 23,933 23,697 22,959 22,809 22,309 M24x1 h 24,000 ----- 23,350 ----- 22,917 M25x2 h 25,000 ----- 23,701 ----- 22,835 M25x1,5 h 25,000 ----- 24,026 ----- 23,376 6g 24,968 24,732 23,994 23,844 23,344 6e 24,933 24,697 23,959 23,809 23,309 M25x1 h 25,000 ----- 24,350 ----- 23,917 M26x1,5 h 26,000 ----- 25,026 ----- 24,376 6g 25,968 25,732 24,994 24,844 24,344 M26x1,5 6e 25,933 25,697 24,959 24,809 24,309 M27(x3) h 27,000 ----- 25,051 ----- 23,752 6g 26,952 26,577 25,003 24,803 23,704 8g 26,952 26,352 25,003 24,688 23,704 6e 26,915 26,540 24,966 24,766 23,667 8e 26,915 26,315 24,966 24,651 23,667 js 27,072 26,622 25,123 24,979 23,391 M27x2 h 27,000 ----- 25,701 ----- 24,835 6g 26,962 26,682 25,663 25,493 24,797 6e 26,929 26,649 25,630 25,460 24,764 M27x1,5 h 27,000 ----- 26,026 ----- 25,376 M27x1 h 27,000 ----- 26,350 ----- 25,917 M28x2 h 28,000 ----- 26,701 ----- 25,835 M28x1,5 h 28,000 ----- 27,026 ----- 26,376 6g 27,968 27,732 26,994 26,844 26,344 6e 27,933 27,697 26,959 26,809 26,309 M28x1 h 28,000 ----- 27,350 ----- 26,917 M30(x3,5) h 30,000 ----- 27,727 ----- 26,211 6g 29,947 29,522 27,674 27,462 26,158 8g 29,947 29,277 27,674 27,339 26,158 6e 29,910 29,485 27,637 27,425 26,121 8e 29,910 29,240 27,637 27,302 26,121


Issue 1 Page 8


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


js 30,078 29,588 27,805 27,649 25,784 M30x3 h 30,000 ----- 28,051 ----- 26,752 M30x2 h 30,000 ----- 28,701 ----- 27,835 6g 29,962 29,682 28,663 28,493 27,797 6e 29,929 29,649 28,630 28,460 27,764 M30x1,5 h 30,000 ----- 29,026 ----- 28,376 6g 29,968 29,732 28,994 28,844 28,344 6e 29,933 29,697 28,959 28,809 28,309 M30x1 h 30,000 ----- 29,350 ----- 28,917 M32x2 h 32,000 ----- 30,701 ----- 29,835 M32x1,5 h 32,000 ----- 31,026 ----- 30,376 6g 31,968 31,732 30,994 30,844 30,344 6e 31,933 31,697 30,959 30,809 30,309 M33(x3,5) h 33,000 ----- 30,727 ----- 29,211 6g 32,947 32,522 30,674 30,462 29,158 8g 32,947 32,277 30,674 30,339 29,158 6e 32,910 32,485 30,637 30,425 29,121 8e 32,910 32,240 30,637 30,302 29,121 js 33,079 32,589 30,806 30,648 28,785 M33x3 h 33,000 ----- 31,051 ----- 29,752 M33x2 h 33,000 ----- 31,701 ----- 30,835 6g 32,962 32,682 31,663 31,493 30,797 M33x2 6e 32,929 32,649 31,630 31,460 30,764 M33x1,5 h 33,000 ----- 32,026 ----- 31,376 M34x1,5 h 34,000 ----- 33,026 ----- 32,376 6g 33,968 33,732 32,994 32,844 32,344 6e 33,933 33,697 32,959 32,809 32,309 M35x1,5 h 35,000 ----- 34,026 ----- 33,376 6g 34,968 34,732 33,994 33,844 33,344 6e 34,933 34,697 33,959 33,809 33,309 M36(x4) h 36,000 ----- 33,402 ----- 31,670 6g 35,940 35,465 33,342 33,118 31,610 8g 35,940 35,190 33,342 32,987 31,610 6e 35,905 35,430 33,307 33,083 31,575 8e 35,905 35,155 33,307 32,952 31,575 js 36,085 35,545 33,487 33,317 31,178 M36x3 h 36,000 ----- 34,051 ----- 32,752 6g 35,952 35,577 34,003 33,803 32,704 6e 35,915 35,540 33,966 33,766 32,667 M36x2 h 36,000 ----- 34,701 ----- 33,835 6g 35,962 35,682 34,663 34,493 33,797 6e 35,929 35,649 34,630 34,460 33,764 M36x1,5 h 36,000 ----- 35,026 ----- 34,376 6g 35,968 35,732 34,994 34,844 34,344 6e 35,933 35,697 34,959 34,809 34,309 M38x1,5 h 38,000 ----- 37,026 ----- 36,376 6g 37,968 37,732 36,994 36,844 36,344 6e 37,933 37,697 36,959 36,809 36,309


Issue 1 Page 9


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M39(x4) h 39,000 ----- 36,402 ----- 34,670 6g 38,940 38,465 36,342 36,118 34,610 8g 38,940 38,190 36,342 35,987 34,610 6e 38,905 38,430 36,307 36,083 34,575 8e 38,905 38,155 36,307 35,952 34,575 js 39,086 38,546 36,488 36,316 34,179 M39x3 h 39,000 ----- 37,051 ----- 35,752 6g 38,952 38,577 37,003 36,803 35,704 6e 38,915 38,540 36,966 36,766 35,667 M39x2 h 39,000 ----- 37,701 ----- 36,835 M39x1,5 h 39,000 ----- 38,026 ----- 37,376 M40x3 h 40,000 ----- 38,051 ----- 36,752 M40x2 h 40,000 ----- 38,701 ----- 37,835 6g 39,962 39,682 38,663 38,493 37,797 6e 39,929 39,649 38,630 38,460 37,764 M40x1,5 h 40,000 ----- 39,026 ----- 38,376 6g 39,968 39,732 38,994 38,844 38,344 6e 39,933 39,697 38,959 38,809 38,309 M42(x4,5) h 42,000 ----- 39,077 ----- 37,129 6g 41,937 41,437 39,014 38,778 37,066 8g 41,937 41,137 39,014 38,639 37,066 6e 41,900 41,400 38,977 38,741 37,029 8e 41,900 41,100 38,977 38,602 37,029 M42x4 h 42,000 ----- 39,402 ----- 37,670 M42x3 h 42,000 ----- 40,051 ----- 38,752 6g 41,952 41,577 40,003 39,803 38,704 6e 41,915 41,540 39,966 39,766 38,667 M42x2 h 42,000 ----- 40,701 ----- 39,835 6g 41,962 41,682 40,663 40,493 39,797 6e 41,929 41,649 40,630 40,460 39,764 M42x1,5 h 42,000 ----- 41,026 ----- 40,376 6g 41,968 41,732 40,994 40,844 40,344 6e 41,933 41,697 40,959 40,809 40,309 M45(x4,5) h 45,000 ----- 42,077 ----- 40,129 6g 44,937 44,437 42,014 41,778 40,066 8g 44,937 44,137 42,014 41,639 40,066 6e 44,900 44,400 41,977 41,741 40,029 8e 44,900 44,100 41,977 41,602 40,029 M45x4 h 45,000 ----- 42,402 ----- 40,670 M45x3 h 45,000 ----- 43,051 ----- 41,752 6g 44,952 44,577 43,003 42,803 41,704 6e 44,915 44,540 42,966 42,766 41,667 M45x2 h 45,000 ----- 43,701 ----- 42,835 6g 44,962 44,682 43,663 43,493 42,797 7g6g 44,962 44,682 43,663 43,451 42,797 8g 44,962 44,512 43,663 43,398 42,797 6e 44,929 44,649 43,630 43,460 42,764 M45x1,5 h 45,000 ----- 44,026 ----- 43,376 6g 44,968 44,732 43,994 43,844 43,344 6e 44,933 44,697 43,959 43,809 43,309


Issue 1 Page 10


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M48(x5) h 48,000 ----- 44,752 ----- 42,587 6g 47,929 47,399 44,681 44,431 42,516 8g 47,929 47,079 44,681 44,281 42,516 6e 47,894 47,364 44,646 44,396 42,481 8e 47,894 47,044 44,646 44,246 42,481 M48x4 h 48,000 ----- 45,402 ----- 43,670 M48x3 h 48,000 ----- 46,051 ----- 44,752 6g 47,952 47,577 46,003 45,791 44,704 6e 47,915 47,540 45,966 45,754 44,667 M48x2 h 48,000 ----- 46,701 ----- 45,835 M48x1,5 h 48,000 ----- 47,026 ----- 46,376 6g 47,968 47,732 46,994 46,834 46,344 M48x1,5 6e 47,933 47,697 46,959 46,809 46,309 M48x1 h 48,000 ----- 47,350 ----- 46,917 6h 48,000 47,820 47,350 47,210 46,917 6e 47,940 47,760 47,290 47,150 46,857 M50x3 h 50,000 ----- 48,051 ----- 46,752 M50x2 h 50,000 ----- 48,701 ----- 47,835 6g 49,962 49,682 48,663 48,483 47,797 6e 49,929 49,649 48,630 48,450 47,764 M50x1,5 h 50,000 ----- 49,026 ----- 48,376 6h 50,000 49,764 49,026 48,866 48,376 6g 49,968 49,732 48,994 48,834 48,344 6e 49,933 49,697 48,959 48,809 48,309 M52(x5) h 52,000 ----- 48,752 ----- 46,587 6g 51,929 51,399 48,681 48,431 46,516 8g 51,929 51,079 48,681 48,281 46,516 6e 51,894 51,364 48,646 48,396 46,481 8e 51,894 51,044 48,646 48,246 46,481 M52x4 h 52,000 ----- 49,402 ----- 47,670 M52x3 h 52,000 ----- 50,051 ----- 48,752 6g 51,952 51,577 50,003 49,791 48,704 6e 51,915 51,540 49,966 49,754 48,667 M52x2 h 52,000 ----- 50,701 ----- 49,835 6g 51,962 51,682 50,663 50,483 49,797 6e 51,929 51,649 50,630 50,450 49,764 M52x1,5 h 52,000 ----- 51,026 ----- 50,376 6g 51,968 51,732 50,994 50,834 50,344 6e 51,933 51,697 50,959 50,809 50,309 M54,6x1 h 54,600 ----- 53,950 ----- 53,517 6g 54,574 54,394 53,924 53,784 53,491 M55x4 h 55,000 ----- 52,402 ----- 50,670 M55x3 h 55,000 ----- 53,051 ----- 51,752 M55x2 h 55,000 ----- 53,701 ----- 52,835 6g 54,962 54,682 53,663 53,483 52,797 6e 54,929 54,649 53,630 53,450 52,764


Issue 1 Page 11


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M55x1,5 h 55,000 ----- 54,026 ----- 53,376 6g 54,968 54,732 53,994 53,834 53,344 6e 54,933 54,697 53,959 53,809 53,309 M56(x5,5) h 56,000 ----- 52,428 ----- 50,046 6g 55,925 55,365 52,353 52,088 49,971 8g 55,925 55,025 52,353 51,928 49,971 6e 55,888 55,328 52,316 52,151 49,934 8e 55,888 54,988 52,316 51,891 49,934 M56x4 h 56,000 ----- 53,402 ----- 51,670 6g 55,940 55,465 53,342 53,106 51,610 M56x4 6e 55,905 55,430 53,307 53,071 51,575 M56x3 h 56,000 ----- 54,051 ----- 52,752 M56x2 h 56,000 ----- 54,701 ----- 53,835 M56x1,5 h 56,000 ----- 55,026 ----- 54,376 M58x4 h 58,000 ----- 55,402 ----- 53,670 M58x3 h 58,000 ----- 56,051 ----- 54,752 M58x2 h 58,000 ----- 56,701 ----- 55,835 6g 57,962 57,682 56,663 56,483 55,797 6e 57,929 57,649 56,630 56,450 55,764 M58x1,5 h 58,000 ----- 57,026 ----- 56,376 M60(x5,5) h 60,000 ----- 56,428 ----- 54,046 6g 59,925 59,365 56,353 56,088 53,971 8g 59,925 59,025 56,353 55,928 53,971 6e 59,888 59,328 56,316 56,151 53,934 8e 59,888 58,988 56,316 55,891 53,934 M60x4 h 60,000 ----- 57,402 ----- 55,670 6g 59,940 59,465 57,342 57,106 55,610 6e 59,905 59,430 57,307 57,071 55,575 M60x3 h 60,000 ----- 58,051 ----- 56,752 M60x2 h 60,000 ----- 58,701 ----- 57,835 6g 59,962 59,682 58,663 58,483 57,797 6e 59,929 59,649 58,630 58,450 57,764 M60x1,5 h 60,000 ----- 59,026 ----- 58,376 M62x4 h 62,000 ----- 59,402 ----- 57,670 M62x3 h 62,000 ----- 60,051 ----- 58,752 M62x2 h 62,000 ----- 60,701 ----- 59,835 6g 61,962 61,682 60,663 60,483 59,797 6e 61,929 61,649 60,630 60,450 59,764 M62x1,5 h 62,000 ----- 61,026 ----- 60.376 M64(x6) h 64,000 ----- 60,103 ----- 57,505 6g 63,920 63,320 60,023 59,743 57,425 8g 63,920 62,970 60,023 59,573 57,425 6e 63,882 63,282 59,985 59,705 57,387 8e 63,882 62,932 59,985 59,535 57,387 M64x4 h 64,000 ----- 61,402 ----- 59,670 6g 63,940 63,465 61,342 61,106 59,610 6e 63,905 63,430 61,307 61,071 59,575 M64x3 h 64,000 ----- 62,051 ----- 60,752


Issue 1 Page 12


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M64x2 h 64,000 ----- 62,701 ----- 61,835 M64x1,5 h 64,000 ----- 63,026 ----- 62,376 M65x4 h 65,000 ----- 62,402 ----- 60,670 M65x3 h 65,000 ----- 63,051 ----- 61,752 M65x2 h 65,000 ----- 63,701 ----- 62,835 6g 64,962 64,682 63,663 63,483 62,797 M65x2 6e 64,929 64,649 63,630 63,450 62,764 M65x1,5 h 65,000 ----- 64,026 ----- 63,376 M68(x6) h 68,000 ----- 64,103 ----- 61,505 6g 67,920 67,320 64,023 63,743 61,425 8g 67,920 66,970 64,023 63,573 61,425 6e 67,882 67,282 63,985 63,705 61,387 8e 67,882 66,932 63,985 63,535 61,387 M68x4 h 68,000 ----- 65,402 ----- 63,670 6g 67,940 67,465 65,342 65,106 63,610 6e 67,905 67,430 65,307 65,071 63,575 M68x3 h 68,000 ----- 66,051 ----- 64,752 M68x2 h 68,000 ----- 66,701 ----- 65,835 6g 67,962 67,682 66,663 66,483 65,797 6e 67,929 67,649 66,630 66,450 65,764 M68x1,5 h 68,000 ----- 67,026 ----- 66,376 M70x6 h 70,000 ----- 66,103 ----- 63,505 M70x4 h 70,000 ----- 67,402 ----- 65,670 M70x3 h 70,000 ----- 68,051 ----- 66,752 M70x2 h 70,000 ----- 68,701 ----- 67,835 6g 69,962 69,682 68,663 68,483 67,797 6e 69,929 69,649 68,630 68,450 67,764 M70x1,5 h 70,000 ----- 69,026 ----- 68,376 M72x6 h 72,000 ----- 68,103 ----- 65,505 M72x4 h 72,000 ----- 69,402 ----- 67,670 6g 71,940 71,465 69,342 69,106 67,610 6e 71,905 71,430 69,307 69,071 67,575 M72x3 h 72,000 ----- 70,051 ----- 68,752 M72x2 h 72,000 ----- 70,701 ----- 69,835 6g 71,962 71,682 70,663 70,483 69,797 6e 71,929 71,649 70,630 70,450 69,764 M72x1,5 h 72,000 ----- 71,026 ----- 70,376 M75x4 h 75,000 ----- 72,402 ----- 70,670 M75x3 h 75,000 ----- 73,051 ----- 71,752 M75x2 h 75,000 ----- 73,701 ----- 72,835 6g 74,962 74,682 73,663 73,483 72,797 6e 74,929 74,649 73,630 73,450 72,764 M75x1,5 h 75,000 ----- 74,026 ----- 73,376 M76x6 h 76,000 ----- 72,103 ----- 69,505 M76x4 h 76,000 ----- 73,402 ----- 71,670 6g 75,940 75,465 73,342 73,106 71,610 6e 75,905 75,430 73,307 73,071 71,575 M76x3 h 76,000 ----- 74,051 ----- 72,752


Issue 1 Page 13


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M76x2 h 76,000 ----- 74,701 ----- 73,835 M76x1,5 h 76,000 ----- 75,026 ----- 74,376 M78x2 h 78,000 ----- 76,701 ----- 75,835 M80x6 h 80,000 ----- 76,103 ----- 73,505 M80x4 h 80,000 ----- 77,402 ----- 75,670 6g 79,940 79,465 77,342 77,106 75,610 6e 79,905 79,430 77,307 77,071 75,575 M80x3 h 80,000 ----- 78,051 ----- 76,752 M80x2 h 80,000 ----- 78,701 ----- 77,835 6g 79,962 79,682 78,663 78,483 77,797 6e 79,929 79,649 78,630 78,450 77,764 M80x1,5 h 80,000 ----- 79,026 ----- 78,376 M82x2 h 82,000 ----- 80,701 ----- 79,835 M85x6 h 85,000 ----- 81,103 ----- 78,505 M85x4 h 85,000 ----- 82,402 ----- 80,670 6g 84,940 84,465 82,342 82,106 80,610 6e 84,905 84,430 82,307 82,071 80,575 M85x3 h 85,000 ----- 83,051 ----- 81,752 M85x2 h 85,000 ----- 83,701 ----- 82,835 6g 84,962 84,682 83,663 83,483 82,797 6e 84,929 84,649 83,630 83,450 82,764 M90x6 h 90,000 ----- 86,103 ----- 83,505 M90x4 h 90,000 ----- 87,402 ----- 85,670 6g 89,940 89,465 87,342 87,106 85,610 6e 89,905 89,430 87,307 87,071 85,575 M90x3 h 90,000 ----- 88,051 ----- 86,752 M90x2 h 90,000 ----- 88,701 ----- 87,835 6g 89,962 89,682 88,663 88,483 87,797 6e 89,929 89,649 88,630 88,450 87,764 M95x6 h 95,000 ----- 91,103 ----- 88,505 M95x4 h 95,000 ----- 92,402 ----- 90,670 6g 94,940 94,465 92,342 92,092 90,610 6e 94,905 94,430 92,307 92,057 90,575 M95x3 h 95,000 ----- 93,051 ----- 91,752 M95x2 h 95,000 ----- 93,701 ----- 92,835 6g 94,962 94,682 93,663 93,473 92,797 6e 94,929 94,649 93,630 93,440 92,764 M100x6 h 100,000 ----- 96,103 ----- 93,505 M100x4 h 100,000 ----- 97,402 ----- 95,670 6g 99,940 99,465 97,342 97,092 95,610 6e 99,905 99,430 97,307 97,057 95,575 M100x3 h 100,000 ----- 98,051 ----- 96,752 M100x2 h 100,000 ----- 98,701 ----- 97,835 6g 99,962 99,682 98,663 98,472 97,797 6e 99,929 99,649 98,630 98,440 97,764 M105x6 h 105,000 ----- 101,103 ----- 98,505 M105x4 h 105,000 ----- 102,402 ----- 100,670 6g 104,940 104,465 102,342 102,092 100,610 6e 104,905 104,430 102,307 102,057 100,575


Issue 1 Page 14


Thread designation


Pitch diameter d2


Gäng-beteckning

Max

Min

Max

Min


M105x3 h 105,000 ----- 103,051 ----- 101,752 M105x2 h 105,000 ----- 103,701 ----- 102,835 6g 104,962 104,682 103,663 103,473 102,797 6e 104,929 104,649 103,630 103,440 102,764 M110x6 h 110,000 ----- 106,103 ----- 103,505 M110x4 h 110,000 ----- 107,402 ----- 105,670 6g 109,940 109,465 107,342 107,092 105,610 6e 109,905 109,430 107,307 107,057 105,575 M110x3 h 110,000 ----- 108,051 ----- 106,752 M110x2 h 110,000 ----- 108,701 ----- 107,835 6g 109,962 109,682 108,663 108,473 107,797 6e 109,929 109,649 108,630 108,440 107,764 M115x6 h 115,000 ----- 111,103 ----- 108,505 M115x4 h 115,000 ----- 112,402 ----- 110,670 6g 114,940 114,465 112,342 112,092 110,610 6e 114,905 114,430 112,307 112,057 110,575 M115x3 h 115,000 ----- 113,051 ----- 111,752 M115x2 h 115,000 ----- 113,701 ----- 112,835 6g 114,962 114,682 113,663 113,473 112,797 6e 114,929 114,649 113,630 113,440 112,764 M120x6 h 120,000 ----- 116,103 ----- 113,505 M120x4 h 120,000 ----- 117,402 ----- 115,670 6g 119,940 119,465 117,342 117,092 115,610 6e 119,905 119,430 117,307 117,057 115,575 M120x3 h 120,000 ----- 118,051 ----- 116,752 M120x2 h 120,000 ----- 118,701 ----- 117,835 6g 119,962 119,682 118,663 118,473 117,797 6e 119,929 119,649 118,630 118,440 117,764 M125x6 h 125,000 ----- 121,103 ----- 118,505 M125x4 h 125,000 ----- 122,402 ----- 120,670 6g 124,940 124,465 122,342 122,092 120,610 6e 124,905 124,430 122,307 122,057 120,575 M125x3 h 125,000 ----- 123,051 ----- 121,752 M125x2 h 125,000 ----- 123,701 ----- 122,835 6g 124,962 124,682 123,663 123,473 122,797 6e 124,929 124,649 123,630 123,440 122,764 M144x4 h 144,000 ----- 141,402 ----- 139,670 6g 143,940 143,465 141,342 141,092 139,610 M148x2 h 148,000 ----- 146,701 ----- 145,835 6g 147,962 147,682 146,663 146,473 145,797 M171x2 h 171,000 ----- 169,701 ----- 168,835 M171x2 6h 171,000 170,720 169,701 169,511 168,835 6g 170,962 170,682 169,663 169,473 168,797 6e 170,929 170,649 169,630 169,440 168,764 M183x2 h 183,000 ----- 181,701 ----- 180,835 6g 182,962 182,682 181,663 181,463 180,797


Issue 1 Page 15


Gränsmått för invändiga gängor Limits of sizes for internal threads

Thread designation

Tol. Major diameter D

Pitch diameter D2 Medeldiameter D2

Minor diameter d1 Innerdiameter d1

Gäng-beteckning

Ytterdia-meter D Min

Max

Min

Max

Min

M3(x0,5) H 3,000 ----- 2,675 ----- 2,459 4H 3,000 2,675 2,549 2,459 5H 3,000 2,675 2,571 2,459 6H 3,000 2,775 2,675 2,599 2,459 7H 3,000 2,675 2,639 2,459 6G6H 3,020 2,795 2,695 2,599 2,459 M3x0,35 H 3,000 ----- 2,773 ----- 2,621 4H 3,000 2,773 2,684 2,621 5H 3,000 2,773 2,701 2,621 6H 3,000 2,863 2,773 2,721 2,621 6G6H 3,019 2,882 2,792 2,721 2,621 M3,5(x0,6) H 3,500 ----- 3,110 ----- 2,850 4H 3,500 3,110 2,950 2,850 5H 3,500 3,110 2,975 2,850 6H 3,500 3,222 3,110 3,010 2,850 7H 3,500 3,110 3,050 2,850 6G6H 3,521 3,243 3,131 3,010 2,850 M3,5x0,35 H 3,500 ----- 3,273 ----- 3,121 4H 3,500 3,273 3,184 3,121 5H 3,500 3,273 3,201 3,121 6H 3,500 3,273 3,221 3,121 M4(x0,7) H 4,000 ----- 3,545 ----- 3,242 4H 4,000 3,545 3,354 3,242 5H 4,000 3,545 3,382 3,242 6H 4,000 3,663 3,545 3,422 3,242 7H 4,000 3,545 3,466 3,242 6G 4,022 3,685 3,567 3,444 3,264 6G6H 4,022 3,685 3,567 3,422 3,242 M4x0,5 H 4,000 ----- 3,675 ----- 3,459 4H 4,000 3,675 3,549 3,459 5H 4,000 3,675 3,571 3,459 6H 4,000 3,775 3,675 3,599 3,459 7H 4,000 3,675 3,639 3,459 6G6H 4,020 3,795 3,695 3,599 3,459 M4,5(x0,75) H 4,500 ----- 4,013 ----- 3,688 4H 4,500 4,013 3,806 3,688 5H 4,500 4,013 3,838 3,688 6H 4,500 4,131 4,013 3,878 3,688 7H 4,500 4,013 3,924 3,688 6G6H 4,522 4,153 4,035 3,878 3,688


Issue 1 Page 16


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M4,5x0,5 H 4,500 ----- 4,175 ----- 3,959 4H 4,500 4,175 4,049 3,959 5H 4,500 4,175 4,071 3,959 6H 4,500 4,175 4,099 3,959 7H 4,500 4,175 4,139 3,959 M5(x0,8) H 5,000 ----- 4,480 ----- 4,134 4H 5,000 4,480 4,259 4,134 5H 5,000 4,480 4,294 4,134 6H 5,000 4,605 4,480 4,334 4,134 7H 5,000 4,640 4,480 4,384 4,134 8H 5,000 4,480 4,449 4,134 6G 5,024 4,629 4,504 4,358 4,158 6G6H 5,024 4,629 4,504 4,334 4,134 7G7H 5,024 4,664 4,504 4,384 4,134 M5x0,5 H 5,000 ----- 4,675 ----- 4,459 4H 5,000 4,675 4,549 4,459 5H 5,000 4,675 4,571 4,459 6H 5,000 4,775 4,675 4,599 4,459 7H 5,000 4,675 4,639 4,459 6G6H 5,020 4,795 4,695 4,599 4,459 M5,5x0,5 H 5,500 ----- 5,175 ----- 4,959 4H 5,500 5,175 5,049 4,959 5H 5,500 5,175 5,071 4,959 6H 5,500 5,175 5,099 4,959 7H 5,500 5,175 5,139 4,959 M6(x1) H 6,000 ----- 5,350 ----- 4,917 4H 6,000 5,350 5,067 4,917 5H 6,000 5,350 5,107 4,917 6H 6,000 5,500 5,350 5,153 4,917 6H7H 6,000 5,500 5,350 5,217 4,917 7H 6,000 5,540 5,350 5,217 4,917 8H 6,000 5,350 5,292 4,917 6G 6,026 5,526 5,376 5,179 4,943 6G6H 6,026 5,526 5,376 5,153 4,917 6G7H 6,026 5,526 5,376 5,217 4,917 7G7H 6,026 5,566 5,376 5,217 4,917 M6x0,75 H 6,000 ----- 5,513 ----- 5,188 4H 6,000 5,513 5,306 5,188 5H 6,000 5,513 5,338 5,188 6H 6,000 5,645 5,513 5,378 5,188 7H 6,000 5,513 5,424 5,188 6G6H 6,022 5,667 5,535 5,378 5,188


Issue 1 Page 17


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M7(x1) H 7,000 ----- 6,350 ----- 5,917 4H 7,000 6,350 6,067 5,917 5H 7,000 6,350 6,107 5,917 6H 7,000 6,500 6,350 6,153 5,917 6H7H 7,000 6,500 6,350 6,217 5,917 7H 7,000 6,540 6,350 6,217 5,917 8H 7,000 6,350 6,292 5,917 6G 7,026 6,526 6,376 6,179 5,943 6G6H 7,026 6,526 6,376 6,153 5,917 6G7H 7,026 6,526 6,376 6,217 5,917 7G7H 7,026 6,566 6,376 6,217 5,917 M7x0,75 H 7,000 ----- 6,513 ----- 6,188 4H 7,000 6,513 6,306 6,188 5H 7,000 6,513 6,338 6,188 6H 7,000 6,513 6,378 6,188 7H 7,000 6,513 6,424 6,188 M8(x1,25) H 8,000 ----- 7,188 ----- 6,647 4H 8,000 7,188 6,817 6,647 5H 8,000 7,188 6,859 6,647 6H 8,000 7,348 7,188 6,912 6,647 6H7H 8,000 7,348 7,188 6,982 6,647 7H 8,000 7,388 7,188 6,982 6,647 8H 8,000 7,188 7,072 6,647 6G 8,028 7,376 7,216 6,940 6,675 6G6H 8,028 7,376 7,216 6,912 6,647 6G7H 8,028 7,376 7,216 6,982 6,647 7G7H 8,028 7,416 7,216 6,982 6,647 M8x1 H 8,000 ----- 7,350 ----- 6,917 4H 8,000 7,350 7,067 6,917 5H 8,000 7,350 7,107 6,917 6H 8,000 7,500 7,350 7,153 6,917 7H 8,000 7,350 7,217 6,917 6G6H 8,026 7,526 7,376 7,153 6,917 M8x0,75 H 8,000 ----- 7,513 ----- 7,188 4H 8,000 7,513 7,306 7,188 5H 8,000 7,513 7,338 7,188 6H 8,000 7,645 7,513 7,378 7,188 7H 8,000 7,513 7,424 7,188 6G6H 8,022 7,667 7,535 7,378 7,188


Issue 1 Page 18


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M9(x1,25) H 9,000 ----- 8,188 ----- 7,647 4H 9,000 8,188 7,817 7,647 5H 9,000 8,188 7,859 7,647 6H 9,000 8,348 8,188 7,912 7,647 6H7H 9,000 8,348 8,188 7,982 7,647 7H 9,000 8,388 8,188 7,982 7,647 8H 9,000 8,188 8,072 7,647 6G6H 9,028 8,376 8,216 7,912 7,647 6G7H 9,028 8,376 8,216 7,982 7,647 7G7H 9,028 8,416 8,216 7,982 7,647 M9x1 H 9,000 ----- 8,350 ----- 7,917 4H 9,000 8,350 8,067 7,917 5H 9,000 8,350 8,107 7,917 6H 9,000 8,350 8,153 7,917 7H 9,000 8,350 8,217 7,917 M9x0,75 H 9,000 ----- 8,513 ----- 8,188 4H 9,000 8,513 8,306 8,188 5H 9,000 8,513 8,338 8,188 6H 9,000 8,513 8,378 8,188 7H 9,000 8,513 8,424 8,188 M10(x1,5) H 10,000 ----- 9,026 ----- 8,376 4H 10,000 9,026 8,566 8,376 5H 10,000 9,026 8,612 8,376 6H 10,000 9,206 9,026 8,676 8,376 6H8H 10,000 9,206 9,026 8,851 8,376 7H 10,000 9,250 9,026 8,751 8,376 8H 10,000 9,026 8,851 8,376 6G 10,032 9,238 9,058 8,708 8,408 6G6H 10,032 9,238 9,058 8,676 8,376 6G8H 10,032 9,238 9,058 8,851 8,376 7G7H 10,032 9,282 9,058 8,751 8,376 M10x1,25 H 10,000 ----- 9,188 ----- 8,647 4H 10,000 9,188 8,817 8,647 5H 10,000 9,188 8,859 8,647 6H 10,000 9,348 9,188 8,912 8,647 7H 10,000 9,188 8,982 8,647 6G6H 10,028 9,376 9,216 8,912 8,647 M10x1 H 10,000 ----- 9,350 ----- 8,917 4H 10,000 9,350 9,067 8,917 5H 10,000 9,350 9,107 8,917 6H 10,000 9,500 9,350 9,153 8,917 7H 10,000 9,350 9,217 8,917 6G6H 10,026 9,526 9,376 9,153 8,917


Issue 1 Page 19


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M10x0,75 H 10,000 ----- 9,513 ----- 9,188 4H 10,000 9,513 9,306 9,188 5H 10,000 9,513 9,338 9,188 6H 10,000 9,513 9,378 9,188 7H 10,000 9,513 9,424 9,188 M11(x1,5) H 11,000 ----- 10,026 ----- 9,376 4H 11,000 10,026 9,566 9,376 5H 11,000 10,026 9,612 9,376 6H 11,000 10,206 10,026 9,676 9,376 6H8H 11,000 10,206 10,026 9,851 9,376 7H 11,000 10,250 10,026 9,751 9,376 8H 11,000 10,026 9,851 9,376 6G6H 11,032 10,238 10,058 9,676 9,376 6G8H 11,032 10,238 10,058 9,851 9,376 7G7H 11,032 10,282 10,058 9,751 9,376 M11x1,25 H 11,000 ----- 10,188 ----- 9,647 4H 11,000 10,188 ----- 9,647 5H 11,000 10,188 9,647 6H 11,000 10,348 10,188 9,912 9,647 7H 11,000 10,188 9,647 8H 11,000 10,438 10,188 10,072 9,647 M11x1 H 11,000 ----- 10,350 ----- 9,917 4H 11,000 10,350 10,067 9,917 5H 11,000 10,350 10,107 9,917 6H 11,000 10,500 10,350 10,153 9,917 7H 11,000 10,350 10,217 9,917 6G6H 11,026 10,526 10,376 10,153 9,917 M11x0,75 H 11,000 ----- 10,513 ----- 10,188 4H 11,000 10,513 10,306 10,188 5H 11,000 10,513 10,338 10,188 6H 11,000 10,513 10,378 10,188 7H 11,000 10,513 10,424 10,188 M12(x1,75) H 12,000 ----- 10,863 ----- 10,106 4H 12,000 10,863 10,318 10,106 5H 12,000 10,863 10,371 10,106 6H 12,000 11,063 10,863 10,441 10,106 6H8H 12,000 11,063 10,863 10,636 10,106 7H 12,000 11,113 10,863 10,531 10,106 8H 12,000 10,863 10,636 10,106 6G 12,034 11,097 10,897 10,475 10,140 6G6H 12,034 11,097 10,897 10,441 10,106 6G8H 12,034 11,097 10,897 10,636 10,106 7G7H 12,034 11,147 10,897 10,531 10,106 7G8H 12,034 11,147 10,897 10,636 10,106


Issue 1 Page 20


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M12x1,59 H 12,000 ----- 10,967 ----- 10,279 6H 12,000 11,157 10,967 10,599 10,279 M12x1,5 H 12,000 ----- 11,026 ----- 10,376 4H 12,000 11,026 10,566 10,376 5H 12,000 11,026 10,612 10,376 6H 12,000 11,216 11,026 10,676 10,376 7H 12,000 11,026 10,751 10,376 6G6H 12,032 11,248 11,058 10,676 10,376 M12x1,25 H 12,000 ----- 11,188 ----- 10,647 4H 12,000 11,188 10,817 10,647 5H 12,000 11,188 10,859 10,647 6H 12,000 11,368 11,188 10,912 10,647 7H 12,000 11,188 10,982 10,647 6G6H 12,028 11,396 11,216 10,912 10,647 M12x1 H 12,000 ----- 11,350 ----- 10,917 4H 12,000 11,350 11,067 10,917 5H 12,000 11,350 11,107 10,917 6H 12,000 11,510 11,350 11,153 10,917 7H 12,000 11,350 11,217 10,917 6G6H 12,026 11,536 11,376 11,153 10,917 M12x0,75 H 12,000 ----- 11,513 ----- 11,188 6H 12,000 11,653 11,513 11,378 11,188 6G6H 12,022 11,675 11,535 11,378 11,188 M14(x2) H 14,000 ----- 12,701 ----- 11,835 4H 14,000 12,701 12,071 11,835 5H 14,000 12,701 12,135 11,835 6H 14,000 12,913 12,701 12,210 11,835 6H8H 14,000 12,913 12,701 12,435 11,835 7H 14,000 12,966 12,701 12,310 11,835 8H 14,000 12,701 12,435 11,835 6G 14,038 12,951 12,739 12,248 11,873 6G6H 14,038 12,951 12,739 12,210 11,835 6G8H 14,038 12,951 12,739 12,435 11,835 7G7H 14,038 13,004 12,739 12,310 11,835 M14x1,5 H 14,000 ----- 13,026 ----- 12,376 4H 14,000 13,026 12,566 12,376 5H 14,000 13,026 12,612 12,376 6H 14,000 13,216 13,026 12,676 12,376 7H 14,000 13,262 13,026 12,751 12,376 6G6H 14,032 13,248 13,058 12,676 12,376


Issue 1 Page 21


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M14x1,25 H 14,000 ----- 13,188 ----- 12,647 4H 14,000 13,188 12,817 12,647 5H 14,000 13,188 12,859 12,647 6H 14,000 13,368 13,188 12,912 12,647 7H 14,000 13,188 12,982 12,647 6G6H 14,028 13,396 13,216 12,912 12,647 M14x1 H 14,000 ----- 13,350 ----- 12,917 4H 14,000 13,350 13,067 12,917 5H 14,000 13,350 13,107 12,917 6H 14,000 13,510 13,350 13,153 12,917 7H 14,000 13,350 13,217 12,917 6G6H 14,026 13,536 13,376 13,153 12,917 M15x2 H 15,000 ----- 13,701 ----- 12,835 6H 15,000 13,913 13,701 13,210 12,835 6G6H 15,038 13,951 13,739 13,210 12,835 M15x1,5 H 15,000 ----- 14,026 ----- 13,376 4H 15,000 14,026 13,566 13,376 5H 15,000 14,026 13,612 13,376 6H 15,000 14,216 14,026 13,676 13,376 7H 15,000 14,026 13,751 13,376 6G6H 15,032 14,248 14,058 13,676 13,376 M15x1 H 15,000 ----- 14,350 ----- 13,917 4H 15,000 14,350 14,067 13,917 5H 15,000 14,350 14,107 13,917 6H 15,000 14,510 14,350 14,153 13,917 7H 15,000 14,350 14,217 13,917 6G6H 15,026 14,536 14,376 14,153 13,917 M16(x2) H 16,000 ----- 14,701 ----- 13,835 4H 16,000 14,701 14,071 13,835 5H 16,000 14,701 14,135 13,835 6H 16,000 14,913 14,701 14,210 13,835 6H8H 16,000 14,913 14,701 14,435 13,835 7H 16,000 14,966 14,701 14,310 13,835 8H 16,000 14,701 14,435 13,835 6G6H 16,038 14,951 14,739 14,210 13,835 6G8H 16,038 14,951 14,739 14,435 13,835 7G7H 16,038 15,004 14,739 14,310 13,835 M16x1,5 H 16,000 ----- 15,026 ----- 14,376 4H 16,000 15,026 14,566 14,376 5H 16,000 15,026 14,612 14,376 6H 16,000 15,216 15,026 14,676 14,376 7H 16,000 15,026 14,751 14,376 6G6H 16,032 15,248 15,058 14,676 14,376


Issue 1 Page 22


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M16x1 H 16,000 ----- 15,350 ----- 14,917 4H 16,000 15,350 15,067 14,917 5H 16,000 15,350 15,107 14,917 6H 16,000 15,510 15,350 15,153 14,917 7H 16,000 15,350 15,217 14,917 6G6H 16,026 15,536 15,376 15,153 14,917 M17x1,5 H 17,000 ----- 16,026 ----- 15,376 4H 17,000 16,026 15,566 15,376 5H 17,000 16,026 15,612 15,376 6H 17,000 16,026 15,676 15,376 7H 17,000 16,026 15,751 15,376 M17x1 H 17,000 ----- 16,350 ----- 15,917 4H 17,000 16,350 16,067 15,917 5H 17,000 16,350 16,107 15,917 6H 17,000 16,510 16,350 16,153 15,917 7H 17,000 16,350 16,217 15,917 6G6H 17,026 16,536 16,376 16,153 15,917 M18(x2,5) H 18,000 ----- 16,376 ----- 15,294 4H 18,000 16,376 15,574 15,294 5H 18,000 16,376 15,649 15,294 6H 18,000 16,600 16,376 15,744 15,294 6H8H 18,000 16,600 16,376 16,004 15,294 7H 18,000 16,656 16,376 15,854 15,294 8H 18,000 16,376 16,004 15,294 6G6H 18,042 16,642 16,418 15,744 15,294 6G8H 18,042 16,642 16,418 16,004 15,294 7G7H 18,042 16,698 16,418 15,854 15,294 M18x2 H 18,000 ----- 16,701 ----- 15,835 4H 18,000 16,701 16,071 15,835 5H 18,000 16,701 16,135 15,835 6H 18,000 16,701 16,210 15,835 7H 18,000 16,701 16,310 15,835 M18x1,5 H 18,000 ----- 17,026 ----- 16,376 4H 18,000 17,026 16,566 16,376 5H 18,000 17,026 16,612 16,376 6H 18,000 17,216 17,026 16,676 16,376 7H 18,000 17,026 16,751 16,376 6G6H 18,032 17,248 17,058 16,676 16,376 M18x1 H 18,000 ----- 17,350 ----- 16,917 4H 18,000 17,350 17,067 16,917 5H 18,000 17,350 17,107 16,917 6H 18,000 17,510 17,350 17,153 16,917 7H 18,000 17,350 17,217 16,917 6G6H 18,026 17,536 17,376 17,153 16,917


Issue 1 Page 23


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M20(x2,5) H 20,000 ----- 18,376 ----- 17,294 4H 20,000 18,376 17,574 17,294 5H 20,000 18,376 17,649 17,294 6H 20,000 18,600 18,376 17,744 17,294 6H8H 20,000 18,600 18,376 18,004 17,294 7H 20,000 18,656 18,376 17,854 17,294 8H 20,000 18,376 18,004 17,294 6G6H 20,042 18,642 18,418 17,744 17,294 6G8H 20,042 18,642 18,418 18,004 17,294 7G7H 20,042 18,698 18,418 17,854 17,294 M20x2 H 20,000 ----- 18,701 ----- 17,835 4H 20,000 18,701 18,071 17,835 5H 20,000 18,701 18,135 17,835 6H 20,000 18,913 18,701 18,210 17,835 7H 20,000 18,701 18,310 17,835 6G6H 20,038 18,951 18,739 18,210 17,835 M20x1,5 H 20,000 ----- 19,026 ----- 18,376 4H 20,000 19,026 18,566 18,376 5H 20,000 19,026 18,612 18,376 6H 20,000 19,216 19,026 18,676 18,376 7H 20,000 19,026 18,751 18,376 6G6H 20,032 19,248 19,058 18,676 18,376 M20x1 H 20,000 ----- 19,350 ----- 18,917 4H 20,000 19,350 19,067 18,917 5H 20,000 19,350 19,107 18,917 6H 20,000 19,510 19,350 19,153 18,917 7H 20,000 19,350 19,217 18,917 6G6H 20,026 19,536 19,376 19,153 18,917 M22(x2,5) H 22,000 ----- 20,376 ----- 19,294 4H 22,000 20,376 19,574 19,294 5H 22,000 20,376 19,649 19,294 6H 22,000 20,600 20,376 19,744 19,294 6H8H 22,000 20,600 20,376 20,004 19,294 7H 22,000 20,656 20,376 19,854 19,294 8H 22,000 20,376 20,004 19,294 6G6H 22,042 20,642 20,418 19,744 19,294 6G8H 22,042 20,642 20,418 20,004 19,294 7G7H 22,042 20,698 20,418 19,854 19,294 M22x2 H 22,000 ----- 20,701 ----- 19,835 4H 22,000 20,701 20,071 19,835 5H 22,000 20,701 20,135 19,835 6H 22,000 20,701 20,210 19,835 7H 22,000 20,701 20,310 19,835


Issue 1 Page 24


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M22x1,5 H 22,000 ----- 21,026 ----- 20,376 4H 22,000 21,026 20,566 20,376 5H 22,000 21,176 21,026 20,612 20,376 6H 22,000 21,216 21,026 20,676 20,376 7H 22,000 21,262 21,026 20,751 20,376 6G6H 22,032 21,248 21,058 20,676 20,376 M22x1 H 22,000 ----- 21,350 ----- 20,917 4H 22,000 21,350 21,067 20,917 5H 22,000 21,350 21,107 20,917 6H 22,000 21,510 21,350 21,153 20,917 7H 22,000 21,350 21,217 20,917 6G6H 22,026 21,536 21,376 21,153 20,917 M24(x3) H 24,000 ----- 22,051 ----- 20,752 4H 24,000 22,051 21,067 20,752 5H 24,000 22,051 21,152 20,752 6H 24,000 22,316 22,051 21,252 20,752 6H8H 24,000 22,316 22,051 21,552 20,752 7H 24,000 22,386 22,051 21,382 20,752 8H 24,000 22,051 21,552 20,752 6G6H 24,048 22,364 22,099 21,252 20,752 6G8H 24,048 22,364 22,099 21,552 20,752 7G7H 24,048 22,434 22,099 21,382 20,752 M24x2 H 24,000 ----- 22,701 ----- 21,835 4H 24,000 22,701 22,071 21,835 5H 24,000 22,701 22,135 21,835 6H 24,000 22,925 22,701 22,210 21,835 7H 24,000 22,701 22,310 21,835 6G6H 24,038 22,963 22,739 22,210 21,835 M24x1,5 H 24,000 ----- 23,026 ----- 22,376 4H 24,000 23,026 22,566 22,376 5H 24,000 23,186 23,026 22,612 22,376 6H 24,000 23,226 23,026 22,676 22,376 7H 24,000 23,026 22,751 22,376 6G6H 24,032 23,258 23,058 22,676 22,376 M24x1 H 24,000 ----- 23,350 ----- 22,917 4H 24,000 23,350 23,067 22,917 5H 24,000 23,350 23,107 22,917 6H 24,000 23,350 23,153 22,917 7H 24,000 23,350 23,217 22,917 M25x2 H 25,000 ----- 23,701 ----- 22,835 4H 25,000 23,701 23,071 22,835 5H 25,000 23,701 23,135 22,835 6H 25,000 23,701 23,210 22,835 7H 25,000 23,701 23,310 22,835


Issue 1 Page 25


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M25x1,5 H 25,000 ----- 24,026 ----- 23,376 4H 25,000 24,026 23,566 23,376 5H 25,000 24,026 23,612 23,376 6H 25,000 24,226 24,026 23,676 23,376 7H 25,000 24,026 23,751 23,376 6G6H 25,032 24,258 24,058 23,676 23,376 M25x1 H 25,000 ----- 24,350 ----- 23,917 4H 25,000 24,350 24,067 23,917 5H 25,000 24,350 24,107 23,917 6H 25,000 24,350 24,153 23,917 7H 25,000 24,350 24,217 23,917 M26x1,5 H 26,000 ----- 25,026 ----- 24,376 4H 26,000 25,026 24,566 24,376 5H 26,000 25,026 24,612 24,376 6H 26,000 25,226 25,026 24,676 24,376 7H 26,000 25,026 24,751 24,376 6G6H 26,032 25,258 25,058 24,676 24,376 M27(x3) H 27,000 ----- 25,051 ----- 23,752 4H 27,000 25,051 24,067 23,752 5H 27,000 25,051 24,152 23,752 6H 27,000 25,316 25,051 24,252 23,752 6H8H 27,000 25,316 25,051 24,552 23,752 7H 27,000 25,386 25,051 24,382 23,752 8H 27,000 25,051 24,552 23,752 6G6H 27,048 25,364 25,099 24,252 23,752 6G8H 27,048 25,364 25,099 24,552 23,752 7G7H 27,048 25,434 25,099 24,382 23,752 M27x2 H 27,000 ----- 25,701 ----- 24,835 4H 27,000 25,701 25,071 24,835 5H 27,000 25,701 25,135 24,835 6H 27,000 25,925 25,701 25,210 24,835 7H 27,000 25,981 25,701 25,310 24,835 6G6H 27,038 25,963 25,739 25,210 24,835 M27x1,5 H 27,000 ----- 26,026 ----- 25,376 4H 27,000 26,026 25,566 25,376 5H 27,000 26,026 25,612 25,376 6H 27,000 26,026 25,676 25,376 7H 27,000 26,026 25,751 25,376 M27x1 H 27,000 ----- 26,350 ----- 25,917 4H 27,000 26,350 26,067 25,917 5H 27,000 26,350 26,107 25,917 6H 27,000 26,350 26,153 25,917 7H 27,000 26,350 26,217 25,917


Issue 1 Page 26


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M28x2 H 28,000 ----- 26,701 ----- 25,835 4H 28,000 26,701 26,071 25,835 5H 28,000 26,701 26,135 25,835 6H 28,000 26,701 26,210 25,835 7H 28,000 26,701 26,310 25,835 M28x1,5 H 28,000 ----- 27,026 ----- 26,376 4H 28,000 27,026 26,566 26,376 5H 28,000 27,026 26,612 26,376 6H 28,000 27,226 27,026 26,676 26,376 7H 28,000 27,026 26,751 26,376 6G6H 28,032 27,258 27,058 26,676 26,376 M28x1 H 28,000 ----- 27,350 ----- 26,917 4H 28,000 27,350 27,067 26,917 5H 28,000 27,350 27,107 26,917 6H 28,000 27,350 27,153 26,917 7H 28,000 27,350 27,217 26,917 M30(x3,5) H 30,000 ----- 27,727 ----- 26,211 4H 30,000 27,727 26,566 26,211 5H 30,000 27,727 26,661 26,211 6H 30,000 28,007 27,727 26,771 26,211 6H8H 30,000 28,007 27,727 27,111 26,211 7H 30,000 28,082 27,727 26,921 26,211 8H 30,000 27,727 27,111 26,211 6G6H 30,053 28,060 27,780 26,771 26,211 6G8H 30,053 28,060 27,780 27,111 26,211 7G7H 30,053 28,135 27,780 26,921 26,211 M30x3 H 30,000 ----- 28,051 ----- 26,752 4H 30,000 28,051 27,067 26,752 5H 30,000 28,051 27,152 26,752 6H 30,000 28,051 27,252 26,752 7H 30,000 28,051 27,382 26,752 M30x2 H 30,000 ----- 28,701 ----- 27,835 4H 30,000 28,701 28,071 27,835 5H 30,000 28,701 28,135 27,835 6H 30,000 28,925 28,701 28,210 27,835 7H 30,000 28,701 28,310 27,835 6G6H 30,038 28,963 28,739 28,210 27,835 M30x1,5 H 30,000 ----- 29,026 ----- 28,376 4H 30,000 29,026 28,566 28,376 5H 30,000 29,026 28,612 28,376 6H 30,000 29,226 29,026 28,676 28,376 7H 30,000 29,026 28,751 28,376 6G6H 30,032 29,258 29,058 28,676 28,376


Issue 1 Page 27


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M30x1 H 30,000 ----- 29,350 ----- 28,917 4H 30,000 29,350 29,067 28,917 5H 30,000 29,350 29,107 28,917 6H 30,000 29,350 29,153 28,917 7H 30,000 29,350 29,217 28,917 M32x2 H 32,000 ----- 30,701 ----- 29,835 4H 32,000 30,701 30,071 29,835 5H 32,000 30,701 30,135 29,835 6H 32,000 30,701 30,210 29,835 7H 32,000 30,701 30,310 29,835 M32x1,5 H 32,000 ----- 31,026 ----- 30,376 4H 32,000 31,026 30,566 30,376 5H 32,000 31,026 30,612 30,376 6H 32,000 31,226 31,026 30,676 30,376 7H 32,000 31,026 30,751 30,376 6G6H 32,032 31,258 31,058 30,676 30,376 M33(x3,5) H 33,000 ----- 30,727 ----- 29,211 4H 33,000 30,727 29,566 29,211 5H 33,000 30,727 29,661 29,211 6H 33,000 31,007 30,727 29,771 29,211 6H8H 33,000 31,007 30,727 30,111 29,211 7H 33,000 31,082 30,727 29,921 29,211 8H 33,000 30,727 30,111 29,211 6G6H 33,053 31,060 30,780 29,771 29,211 6G8H 33,053 31,060 30,780 30,111 29,211 7G7H 33,053 31,135 30,780 29,921 29,211 M33x3 H 33,000 ----- 31,051 ----- 29,752 4H 33,000 31,051 30,067 29,752 5H 33,000 31,051 30,152 29,752 6H 33,000 31,051 30,252 29,752 7H 33,000 31,051 30,382 29,752 M33x2 H 33,000 ----- 31,701 ----- 30,835 4H 33,000 31,701 31,071 30,835 5H 33,000 31,701 31,135 30,835 6H 33,000 31,925 31,701 31,210 30,835 7H 33,000 31,701 31,310 30,835 6G6H 33,038 31,963 31,739 31,210 30,835 M33x1,5 H 33,000 ----- 32,026 ----- 31,376 4H 33,000 32,026 31,566 31,376 5H 33,000 32,026 31,612 31,376 6H 33,000 32,026 31,676 31,376 7H 33,000 32,026 31,751 31,376 M34x1,5 H 34,000 ----- 33,026 ----- 32,376 6H 34,000 33,226 33,026 32,676 32,376 6G6H 34,032 33,258 33,058 32,676 32,376


Issue 1 Page 28


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M35x1,5 H 35,000 ----- 34,026 ----- 33,376 4H 35,000 34,026 33,566 33,376 5H 35,000 34,026 33,612 33,376 6H 35,000 34,226 34,026 33,676 33,376 7H 35,000 34,026 33,751 33,376 6G6H 35,032 34,258 34,058 33,676 33,376 M36(x4) H 36,000 ----- 33,402 ----- 31,670 4H 36,000 33,402 32,045 31,670 5H 36,000 33,402 32,145 31,670 6H 36,000 33,702 33,402 32,270 31,670 6H8H 36,000 33,702 33,402 32,620 31,670 7H 36,000 33,777 33,402 32,420 31,670 8H 36,000 33,402 32,620 31,670 6G6H 36,060 33,762 33,462 32,270 31,670 6G8H 36,060 33,762 33,462 32,620 31,670 7G7H 36,060 33,837 33,462 32,420 31,670 M36x3 H 36,000 ----- 34,051 ----- 32,752 4H 36,000 34,051 33,067 32,752 5H 36,000 34,051 33,152 32,752 6H 36,000 34,316 34,051 33,252 32,752 7H 36,000 34,051 33,382 32,752 6G6H 36,048 34,364 34,099 33,252 32,752 M36x2 H 36,000 ----- 34,701 ----- 33,835 4H 36,000 34,701 34,071 33,835 5H 36,000 34,701 34,135 33,835 6H 36,000 34,925 34,701 34,210 33,835 7H 36,000 34,701 34,310 33,835 6G6H 36,038 34,963 34,739 34,210 33,835 M36x1,5 H 36,000 ----- 35,026 ----- 34,376 4H 36,000 35,026 34,566 34,376 5H 36,000 35,026 34,612 34,376 6H 36,000 35,226 35,026 34,676 34,376 7H 36,000 35,026 34,751 34,376 6G6H 36,032 35,258 35,058 34,676 34,376 M38x1,5 H 38,000 ----- 37,026 ----- 36,376 4H 38,000 37,026 36,566 36,376 5H 38,000 37,026 36,612 36,376 6H 38,000 37,226 37,026 36,676 36,376 7H 38,000 37,026 36,751 36,376 6G6H 38,032 37,258 37,058 36,676 36,376


Issue 1 Page 29


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M39(x4) H 39,000 ----- 36,402 ----- 34,670 4H 39,000 36,402 35,045 34,670 5H 39,000 36,402 35,145 34,670 6H 39,000 36,702 36,402 35,270 34,670 6H8H 39,000 36,702 36,402 35,620 34,670 7H 39,000 36,777 36,402 35,420 34,670 8H 39,000 36,402 35,620 34,670 6G6H 39,060 36,762 36,462 35,270 34,670 6G8H 39,060 36,762 36,462 35,620 34,670 7G7H 39,060 36,837 36,462 35,420 34,670 M39x3 H 39,000 ----- 37,051 ----- 35,752 4H 39,000 37,051 36,067 35,752 5H 39,000 37,051 36,152 35,752 6H 39,000 37,316 37,051 36,252 35,752 7H 39,000 37,051 36,382 35,752 6G6H 39,048 37,364 37,099 36,252 35,752 M39x2 H 39,000 ----- 37,701 ----- 36,835 4H 39,000 37,701 37,071 36,835 5H 39,000 37,701 37,135 36,835 6H 39,000 37,701 37,210 36,835 7H 39,000 37,701 37,310 36,835 M39x1,5 H 39,000 ----- 38,026 ----- 37,376 4H 39,000 38,026 37,566 37,376 5H 39,000 38,026 37,612 37,376 6H 39,000 38,026 37,676 37,376 7H 39,000 38,026 37,751 37,376 M40x3 H 40,000 ----- 38,051 ----- 36,752 4H 40,000 38,051 37,067 36,752 5H 40,000 38,051 37,152 36,752 6H 40,000 38,051 37,252 36,752 7H 40,000 38,051 37,382 36,752 M40x2 H 40,000 ----- 38,701 ----- 37,835 4H 40,000 38,701 38,071 37,835 5H 40,000 38,701 38,135 37,835 6H 40,000 38,925 38,701 38,210 37,835 7H 40,000 38,701 38,310 37,835 6G6H 40,038 38,963 38,739 38,210 37,835 M40x1,5 H 40,000 ----- 39,026 ----- 38,376 4H 40,000 39,026 38,566 38,376 5H 40,000 39,026 38,612 38,376 6H 40,000 39,226 39,026 38,676 38,376 7H 40,000 39,026 38,751 38,376 6G6H 40,032 39,258 39,058 38,676 38,376


Issue 1 Page 30


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M42(x4,5) H 42,000 ----- 39,077 ----- 37,129 4H 42,000 39,077 37,554 37,129 5H 42,000 39,077 37,659 37,129 6H 42,000 39,392 39,077 37,799 37,129 6H8H 42,000 39,392 39,077 38,189 37,129 7H 42,000 39,477 39,077 37,979 37,129 8H 42,000 39,077 38,189 37,129 6G6H 42,063 39,455 39,140 37,799 37,129 6G8H 42,063 39,455 39,140 38,189 37,129 7G7H 42,063 39,540 39,140 37,979 37,129 M42x4 H 42,000 ----- 39,402 ----- 37,670 4H 42,000 39,402 38,045 37,670 5H 42,000 39,402 38,145 37,670 6H 42,000 39,402 38,270 37,670 7H 42,000 39,402 38,420 37,670 M42x3 H 42,000 ----- 40,051 ----- 38,752 4H 42,000 40,051 39,067 38,752 5H 42,000 40,051 39,152 38,752 6H 42,000 40,316 40,051 39,252 38,752 7H 42,000 40,051 39,382 38,752 6G6H 42,048 40,364 40,099 39,252 38,752 M42x2 H 42,000 ----- 40,701 ----- 39,835 4H 42,000 40,701 40,071 39,835 5H 42,000 40,701 40,135 39,835 6H 42,000 40,925 40,701 40,210 39,835 7H 42,000 40,701 40,310 39,835 6G6H 42,038 40,963 40,739 40,210 39,835 M42x1,5 H 42,000 ----- 41,026 ----- 40,376 4H 42,000 41,026 40,566 40,376 5H 42,000 41,026 40,612 40,376 6H 42,000 41,226 41,026 40,676 40,376 7H 42,000 41,026 40,751 40,376 6G6H 42,058 41,258 41,058 40,676 40,376 M45(x4,5) H 45,000 ----- 42,077 ----- 40,129 4H 45,000 42,077 40,554 40,129 5H 45,000 42,077 40,659 40,129 6H 45,000 42,392 42,077 40,799 40,129 6H8H 45,000 42,392 42,077 41,189 40,129 7H 45,000 42,477 42,077 40,979 40,129 8H 45,000 42,077 41,189 40,129 6G6H 45,063 42,455 42,140 40,799 40,129 6G8H 45,063 42,455 42,140 41,189 40,129 7G7H 45,063 42,540 42,140 40,979 40,129


Issue 1 Page 31


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M45x4 H 45,000 ----- 42,402 ----- 40,670 4H 45,000 42,402 41,045 40,670 5H 45,000 42,402 41,145 40,670 6H 45,000 42,402 41,270 40,670 7H 45,000 42,402 41,420 40,670 M45x3 H 45,000 ----- 43,051 ----- 41,752 4H 45,000 43,051 42,067 41,752 5H 45,000 43,051 42,152 41,752 6H 45,000 43,316 43,051 42,252 41,752 7H 45,000 43,051 42,382 41,752 6G6H 45,048 43,364 43,099 42,252 41,752 M45x2 H 45,000 ----- 43,701 ----- 42,835 4H 45,000 43,701 43,071 42,835 5H 45,000 43,701 43,135 42,835 6H 45,000 43,925 43,701 43,210 42,835 7H 45,000 43,701 43,310 42,835 6G6H 45,038 43,963 43,739 43,210 42,835 M45x1,5 H 45,000 ----- 44,026 ----- 43,376 4H 45,000 44,026 43,566 43,376 5H 45,000 44,026 43,612 43,376 6H 45,000 44,226 44,026 43,676 43,376 7H 45,000 44,026 43,751 43,376 6G6H 45,032 44,258 44,058 43,676 43,376 M48(x5) H 48,000 ----- 44,752 ----- 42,587 4H 48,000 44,752 43,037 42,587 5H 48,000 44,752 43,147 42,587 6H 48,000 45,087 44,752 43,297 42,587 6H8H 48,000 45,087 44,752 43,707 42,587 7H 48,000 45,177 44,752 43,487 42,587 8H 48,000 44,752 43,707 42,587 6G6H 48,071 45,158 44,823 43,297 42,587 6G8H 48,071 45,158 44,823 43,707 42,587 7G7H 48,071 45,248 44,823 43,487 42,587 M48x4 H 48,000 ----- 45,402 ----- 43,670 4H 48,000 45,402 44,045 43,670 5H 48,000 45,402 44,145 43,670 6H 48,000 45,402 44,270 43,670 7H 48,000 45,402 44,420 43,670 M48x3 H 48,000 ----- 46,051 ----- 44,752 4H 48,000 46,051 45,067 44,752 5H 48,000 46,051 45,152 44,752 6H 48,000 46,331 46,051 45,252 44,752 7H 48,000 46,051 45,382 44,752 6G6H 48,048 46,364 46,099 45,252 44,752


Issue 1 Page 32


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M48x2 H 48,000 ----- 46,701 ----- 45,835 4H 48,000 46,701 46,071 45,835 5H 48,000 46,701 46,135 45,835 6H 48,000 46,701 46,210 45,835 7H 48,000 46,701 46,310 45,835 M48x1,5 H 48,000 ----- 47,026 ----- 46,376 4H 48,000 47,026 46,566 46,376 5H 48,000 47,026 46,612 46,376 6H 48,000 47,238 47,026 46,676 46,376 7H 48,000 47,026 46,751 46,376 6G6H 48,032 47,270 47,058 46,676 46,376 M48x1 H 48,000 ----- 47,350 ----- 46,917 6H 48,000 47,530 47,350 47,153 46,917 6G6H 48,026 47,556 47,376 47,153 46,917 M50x3 H 50,000 ----- 48,051 ----- 46,752 4H 50,000 48,051 47,067 46,752 5H 50,000 48,051 47,152 46,752 6H 50,000 48,051 47,252 46,752 7H 50,000 48,051 47,382 46,752 M50x2 H 50,000 ----- 48,701 ----- 47,835 4H 50,000 48,701 48,071 47,835 5H 50,000 48,701 48,135 47,835 6H 50,000 48,937 48,701 48,210 47,835 7H 50,000 48,701 48,310 47,835 6G6H 50,038 48,975 48,739 48,210 47,835 M50x1,5 H 50,000 ----- 49,026 ----- 48,376 4H 50,000 49,026 48,566 48,376 5H 50,000 49,196 49,026 48,612 48,376 6H 50,000 49,238 49,026 48,676 48,376 7H 50,000 49,026 48,751 48,376 6G6H 50,032 49,270 49,058 48,676 48,376 M52(x5) H 52,000 ----- 48,752 ----- 46,587 4H 52,000 48,752 47,037 46,587 5H 52,000 48,752 47,147 46,587 6H 52,000 49,087 48,752 47,297 46,587 6H8H 52,000 49,087 48,752 47,707 46,587 7H 52,000 49,177 48,752 47,487 46,587 8H 52,000 48,752 47,707 46,587 6G6H 52,071 49,158 48,823 47,297 46,587 6G8H 52,071 49,158 48,823 47,707 46,587 7G7H 52,071 49,248 48,823 47,487 46,587 M52x4 H 52,000 ----- 49,402 ----- 47,670 4H 52,000 49,402 48,045 47,670 5H 52,000 49,402 48,145 47,670 6H 52,000 49,402 48,270 47,670 7H 52,000 49,402 48,420 47,670


Issue 1 Page 33


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M52x3 H 52,000 ----- 50,051 ----- 48,752 4H 52,000 50,051 49,067 48,752 5H 52,000 50,051 49,152 48,752 6H 52,000 50,331 50,051 49,252 48,752 7H 52,000 50,051 49,382 48,752 6G6H 52,048 50,364 50,099 49,252 48,752 M52x2 H 52,000 ----- 50,701 ----- 49,835 4H 52,000 50,701 50,071 49,835 5H 52,000 50,701 50,135 49,835 6H 52,000 50,937 50,701 50,210 49,835 7H 52,000 50,701 50,310 49,835 6G6H 52,038 50,975 50,739 50,210 49,835 M52x1,5 H 52,000 ----- 51,026 ----- 50,376 4H 52,000 51,026 50,566 50,376 5H 52,000 51,026 50,612 50,376 6H 52,000 51,238 51,026 50,676 50,376 7H 52,000 51,026 50,751 50,376 6G6H 52,032 51,270 51,058 50,676 50,376 M54,6x1 H 54,600 ----- 53,950 ----- 53,517 M55x4 H 55,000 ----- 52,402 ----- 50,670 4H 55,000 52,402 51,045 50,670 5H 55,000 52,402 51,145 50,670 6H 55,000 52,402 51,270 50,670 7H 55,000 52,402 51,420 50,670 M55x3 H 55,000 ----- 53,051 ----- 51,752 4H 55,000 53,051 52,067 51,752 5H 55,000 53,051 52,152 51,752 6H 55,000 53,051 52,252 51,752 7H 55,000 53,051 52,382 51,752 M55x2 H 55,000 ----- 53,701 ----- 52,835 4H 55,000 53,701 53,071 52,835 5H 55,000 53,701 53,135 52,835 6H 55,000 53,937 53,701 53,210 52,835 7H 55,000 53,701 53,310 52,835 6G6H 55,038 53,975 53,739 53,210 52,835 M55x1,5 H 55,000 ----- 54,026 ----- 53,376 4H 55,000 54,026 53,566 53,376 5H 55,000 54,026 53,612 53,376 6H 55,000 54,238 54,026 53,676 53,376 7H 55,000 54,026 53,751 53,376 6G6H 55,032 54,270 54,058 53,676 53,376


Issue 1 Page 34


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M56(x5,5) H 56,000 ----- 52,428 ----- 50,046 4H 56,000 52,428 50,521 50,046 5H 56,000 52,428 50,646 50,046 6H 56,000 52,783 52,428 50,796 50,046 6H8H 56,000 52,783 52,428 51,226 50,046 7H 56,000 52,878 52,428 50,996 50,046 8H 56,000 52,428 51,226 50,046 6G6H 56,075 52,858 52,503 50,796 50,046 6G8H 56,075 52,858 52,503 51,226 50,046 7G7H 56,075 52,953 52,503 50,996 50,046 M56x4 H 56,000 ----- 53,402 ----- 51,670 4H 56,000 53,402 52,045 51,670 5H 56,000 53,402 52,145 51,670 6H 56,000 53,717 53,402 52,270 51,670 7H 56,000 53,402 52,420 51,670 6G6H 56,060 53,777 53,462 52,270 51,670 M56x3 H 56,000 ----- 54,051 ----- 52,752 4H 56,000 54,051 53,067 52,752 5H 56,000 54,051 53,152 52,752 6H 56,000 54,051 53,252 52,752 7H 56,000 54,051 53,382 52,752 M56x2 H 56,000 ----- 54,701 ----- 53,835 4H 56,000 54,701 54,071 53,835 5H 56,000 54,701 54,135 53,835 6H 56,000 54,701 54,210 53,835 7H 56,000 54,701 54,310 53,835 M56x1,5 H 56,000 ----- 55,026 ----- 54,376 4H 56,000 55,026 54,566 54,376 5H 56,000 55,026 54,612 54,376 6H 56,000 55,026 54,676 54,376 7H 56,000 55,026 54,751 54,376 M58x4 H 58,000 ----- 55,402 ----- 53,670 4H 58,000 55,402 54,045 53,670 5H 58,000 55,402 54,145 53,670 6H 58,000 55,402 54,270 53,670 7H 58,000 55,402 54,420 53,670 M58x3 H 58,000 ----- 56,051 ----- 54,752 4H 58,000 56,051 55,067 54,752 5H 58,000 56,051 55,152 54,752 6H 58,000 56,051 55,252 54,752 7H 58,000 56,051 55,382 54,752 M58x2 H 58,000 ----- 56,701 ----- 55,835 4H 58,000 56,701 56,071 55,835 5H 58,000 56,701 56,135 55,835 6H 58,000 56,937 56,701 56,210 55,835 7H 58,000 56,701 56,310 55,835 6G6H 58,038 56,975 56,739 56,210 55,835


Issue 1 Page 35


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M58x1,5 H 58,000 ----- 57,026 ----- 56,376 4H 58,000 57,026 56,566 56,376 5H 58,000 57,026 56,612 56,376 6H 58,000 57,026 56,676 56,376 7H 58,000 57,026 56,751 56,376 M60(x5,5) H 60,000 ----- 56,428 ----- 54,046 4H 60,000 56,428 54,521 54,046 5H 60,000 56,428 54,646 54,046 6H 60,000 56,783 56,428 54,796 54,046 6H8H 60,000 56,783 56,428 55,226 54,046 7H 60,000 56,878 56,428 54,996 54,046 8H 60,000 56,428 55,226 54,046 6G6H 60,075 56,858 56,503 54,796 54,046 6G8H 60,075 56,858 56,503 55,226 54,046 7G7H 60,075 56,953 56,503 54,996 54,046 M60x4 H 60,000 ----- 57,402 ----- 55,670 4H 60,000 57,402 56,045 55,670 5H 60,000 57,402 56,145 55,670 6H 60,000 57,717 57,402 56,270 55,670 7H 60,000 57,402 56,420 55,670 6G6H 60,060 57,777 57,462 56,270 55,670 M60x3 H 60,000 ----- 58,051 ----- 56,752 4H 60,000 58,051 57,067 56,752 5H 60,000 58,051 57,152 56,752 6H 60,000 58,051 57,252 56,752 7H 60,000 58,051 57,382 56,752 M60x2 H 60,000 ----- 58,701 ----- 57,835 4H 60,000 58,701 58,071 57,835 5H 60,000 58,701 58,135 57,835 6H 60,000 58,937 58,701 58,210 57,835 7H 60,000 58,701 58,310 57,835 6G6H 60,038 58,975 58,739 58,210 57,835 M60x1,5 H 60,000 ----- 59,026 ----- 58,376 4H 60,000 59,026 58,566 58,376 5H 60,000 59,026 58,612 58,376 6H 60,000 59,026 58,676 58,376 7H 60,000 59,026 58,751 58,376 M62x4 H 62,000 ----- 59,402 ----- 57,670 4H 62,000 59,402 58,045 57,670 5H 62,000 59,402 58,145 57,670 6H 62,000 59,402 58,270 57,670 7H 62,000 59,402 58,420 57,670 M62x3 H 62,000 ----- 60,051 ----- 58,752 4H 62,000 60,051 59,067 58,752 5H 62,000 60,051 59,152 58,752 6H 62,000 60,051 59,252 58,752 7H 62,000 60,051 59,382 58,752


Issue 1 Page 36


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M62x2 H 62,000 ----- 60,701 ----- 59,835 4H 62,000 60,701 60,071 59,835 5H 62,000 60,701 60,135 59,835 6H 62,000 60,937 60,701 60,210 59,835 7H 62,000 60,701 60,310 59,835 6G6H 62,038 60,975 60,739 60,210 59,835 M62x1,5 H 62,000 ----- 61,026 ----- 60.376 4H 62,000 61,026 60,566 60,376 5H 62,000 61,026 60,612 60,376 6H 62,000 61,026 60,676 60,376 7H 62,000 61,026 60,751 60,376 M64(x6) H 64,000 ----- 60,103 ----- 57,505 4H 64,000 60,103 58,005 57,505 5H 64,000 60,103 58,135 57,505 6H 64,000 60,478 60,103 58,305 57,505 6H8H 64,000 60,478 60,103 58,755 57,505 7H 64,000 60,578 60,103 58,505 57,505 8H 64,000 60,103 58,755 57,505 6G6H 64,080 60,558 60,183 58,305 57,505 6G8H 64,080 60,558 60,183 58,755 57,505 7G7H 64,080 60,858 60,183 58,505 57,505 M64x4 H 64,000 ----- 61,402 ----- 59,670 4H 64,000 61,402 60,045 59,670 5H 64,000 61,402 60,145 59,670 6H 64,000 61,717 61,402 60,270 59,670 7H 64,000 61,402 60,420 59,670 6G6H 64,060 61,777 61,462 60,270 59,670 M64x3 H 64,000 ----- 62,051 ----- 60,752 4H 64,000 62,051 61,067 60,752 5H 64,000 62,051 61,152 60,752 6H 64,000 62,051 61,252 60,752 7H 64,000 62,051 61,382 60,752 M64x2 H 64,000 ----- 62,701 ----- 61,835 4H 64,000 62,701 62,071 61,835 5H 64,000 62,701 62,135 61,835 6H 64,000 62,701 62,210 61,835 7H 64,000 62,701 62,310 61,835 M64x1,5 H 64,000 ----- 63,026 ----- 62,376 4H 64,000 63,026 62,566 62,376 5H 64,000 63,026 62,612 62,376 6H 64,000 63,026 62,676 62,376 7H 64,000 63,026 62,751 62,376 M65x4 H 65,000 ----- 62,402 ----- 60,670 4H 65,000 62,402 61,045 60,670 5H 65,000 62,402 61,145 60,670 6H 65,000 62,402 61,270 60,670 7H 65,000 62,402 61,420 60,670


Issue 1 Page 37


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M65x3 H 65,000 ----- 63,051 ----- 61,752 4H 65,000 63,051 62,067 61,752 5H 65,000 63,051 62,152 61,752 6H 65,000 63,051 62,252 61,752 7H 65,000 63,051 62,382 61,752 M65x2 H 65,000 ----- 63,701 ----- 62,835 4H 65,000 63,701 63,071 62,835 5H 65,000 63,701 63,135 62,835 6H 65,000 63,937 63,701 63,210 62,835 7H 65,000 63,701 63,310 62,835 6G6H 65,038 63,975 63,739 63,210 62,835 M65x1,5 H 65,000 ----- 64,026 ----- 63,376 4H 65,000 64,026 63,566 63,376 5H 65,000 64,026 63,612 63,376 6H 65,000 64,026 63,676 63,376 7H 65,000 64,026 63,751 63,376 M68(x6) H 68,000 ----- 64,103 ----- 61,505 4H 68,000 64,103 62,005 61,505 5H 68,000 64,103 62,135 61,505 6H 68,000 64,478 64,103 62,305 61,505 6H8H 68,000 64,478 64,103 62,755 61,505 7H 68,000 64,578 64,103 62,505 61,505 8H 68,000 64,103 62,755 61,505 6G6H 68,080 64,558 64,183 62,305 61,505 6G8H 68,080 64,558 64,183 62,755 61,505 7G7H 68,080 64,658 64,183 62,505 61,505 M68x4 H 68,000 ----- 65,402 ----- 63,670 4H 68,000 65,402 64,045 63,670 5H 68,000 65,402 64,145 63,670 6H 68,000 65,717 65,402 64,270 63,670 7H 68,000 65,402 64,420 63,670 6G6H 68,060 65,777 65,462 64,270 63,670 M68x3 H 68,000 ----- 66,051 ----- 64,752 4H 68,000 66,051 65,067 64,752 5H 68,000 66,051 65,152 64,752 6H 68,000 66,051 65,252 64,752 7H 68,000 66,051 65,382 64,752 M68x2 H 68,000 ----- 66,701 ----- 65,835 4H 68,000 66,701 66,071 65,835 5H 68,000 66,701 66,135 65,835 6H 68,000 66,937 66,701 66,210 65,835 7H 68,000 66,701 66,310 65,835 6G6H 68,038 66,975 66,739 66,210 65,835


Issue 1 Page 38


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M68x1,5 H 68,000 ----- 67,026 ----- 66,376 4H 68,000 67,026 66,566 66,376 5H 68,000 67,026 66,612 66,376 6H 68,000 67,026 66,676 66,376 7H 68,000 67,026 66,751 66,376 M70x6 H 70,000 ----- 66,103 ----- 63,505 M70x4 H 70,000 ----- 67,402 ----- 65,670 M70x3 H 70,000 ----- 68,051 ----- 66,752 M70x2 H 70,000 ----- 68,701 ----- 67,835 6H 70,000 68,937 68,701 68,210 67,835 6G6H 70,038 68,975 68,739 68,210 67,835 M70x1,5 H 70,000 ----- 69,026 ----- 68,376 M72x6 H 72,000 ----- 68,103 ----- 65,505 M72x4 H 72,000 ----- 69,402 ----- 67,670 6H 72,000 69,717 69,402 68,270 67,670 6G6H 72,060 69,777 69,462 68,270 67,670 M72x3 H 72,000 ----- 70,051 ----- 68,752 M72x2 H 72,000 ----- 70,701 ----- 69,835 6H 72,000 70,937 70,701 70,210 69,835 6G6H 72,038 70,975 70,739 70,210 69,835 M72x1,5 H 72,000 ----- 71,026 ----- 70,376 M75x4 H 75,000 ----- 72,402 ----- 70,670 M75x3 H 75,000 ----- 73,051 ----- 71,752 M75x2 H 75,000 ----- 73,701 ----- 72,835 6H 75,000 73,937 73,701 73,210 72,835 6G6H 75,038 74,975 73,739 73,210 72,835 M75x1,5 H 75,000 ----- 74,026 ----- 73,376 M76x6 H 76,000 ----- 72,103 ----- 69,505 M76x4 H 76,000 ----- 73,402 ----- 71,670 6H 76,000 73,717 73,402 72,270 71,670 6G6H 76,060 73,777 73,462 72,270 71,670 M76x3 H 76,000 ----- 74,051 ----- 72,752 M76x2 H 76,000 ----- 74,701 ----- 73,835 M76x1,5 H 76,000 ----- 75,026 ----- 74,376 M78x2 H 78,000 ----- 76,701 ----- 75,835 M80x6 H 80,000 ----- 76,103 ----- 73,505 M80x4 H 80,000 ----- 77,402 ----- 75,670 6H 80,000 77,717 77,402 76,270 75,670 6G6H 80,060 77,777 77,462 76,270 75,670 M80x3 H 80,000 ----- 78,051 ----- 76,752 M80x2 H 80,000 ----- 78,701 ----- 77,835 6H 80,000 78,937 78,701 78,210 77,835 6G6H 80,038 78,975 78,739 78,210 77,835 M80x1,5 H 80,000 ----- 79,026 ----- 78,376 M82x2 H 82,000 ----- 80,701 ----- 79,835 M85x6 H 85,000 ----- 81,103 ----- 78,505


Issue 1 Page 39


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M85x4 H 85,000 ----- 82,402 ----- 80,670 6H 85,000 82,717 82,402 81,270 80,670 6G6H 85,060 82,777 82,462 81,270 80,670 M85x3 H 85,000 ----- 83,051 ----- 81,752 M85x2 H 85,000 ----- 83,701 ----- 82,835 6H 85,000 83,937 83,701 83,210 82,835 6G6H 85,038 83,975 83,739 83,210 82,835 M90x6 H 90,000 ----- 86,103 ----- 83,505 M90x4 H 90,000 ----- 87,402 ----- 85,670 6H 90,000 87,717 87,402 86,270 85,670 6G6H 90,060 87,777 87,462 86,270 85,670 M90x3 H 90,000 ----- 88,051 ----- 86,752 M90x2 H 90,000 ----- 88,701 ----- 87,835 5H 90,000 88,891 88,701 88,135 87,835 6H 90,000 88,937 88,701 88,210 87,835 6G6H 90,038 88,975 88,739 88,210 87,835 M95x6 H 95,000 ----- 91,103 ----- 88,505 M95x4 H 95,000 ----- 92,402 ----- 90,670 6H 95,000 92,737 92,402 91,270 90,670 6G6H 95,060 92,797 92,462 91,270 90,670 M95x3 H 95,000 ----- 93,051 ----- 91,752 M95x2 H 95,000 ----- 93,701 ----- 92,835 6H 95,000 93,951 93,701 93,210 92,835 6G6H 95,038 93,989 93,739 93,210 92,835 M100x6 H 100,000 ----- 96,103 ----- 93,505 M100x4 H 100,000 ----- 97,402 ----- 95,670 6H 100,000 97,737 97,402 96,270 95,670 6G6H 100,060 97,797 97,462 96,270 95,670 M100x3 H 100,000 ----- 98,051 ----- 96,752 M100x2 H 100,000 ----- 98,701 ----- 97,835 6H 100,000 98,951 98,701 98,210 97,835 6G6H 100,038 98,989 98,739 98,210 97,835 M105x6 H 105,000 ----- 101,103 ----- 98,505 M105x4 H 105,000 ----- 102,402 ----- 100,670 6H 105,000 102,737 102,402 101,270 100,670 6G6H 105,060 102,797 102,462 101,270 100,670 M105x3 H 105,000 ----- 103,051 ----- 101,752 M105x2 H 105,000 ----- 103,701 ----- 102,835 6H 105,000 103,951 103,701 103,210 102,835 6G6H 105,038 103,989 103,739 103,210 102,835 M110x6 H 110,000 ----- 106,103 ----- 103,505 M110x4 H 110,000 ----- 107,402 ----- 105,670 6H 110,000 107,737 107,402 106,270 105,670 6G6H 110,060 107,797 107,462 106,270 105,670 M110x3 H 110,000 ----- 108,051 ----- 106,752


Issue 1 Page 40


Thread designation




Gäng-beteckning


Max

Min

Max

Min

M110x2 H 110,000 ----- 108,701 ----- 107,835 6H 110,000 108,951 108,701 108,210 107,835 6G6H 110,038 108,989 108,739 108,210 107,835 M115x6 H 115,000 ----- 111,103 ----- 108,505 M115x4 H 115,000 ----- 112,402 ----- 110,670 6H 115,000 112,737 112,402 111,270 110,670 6G6H 115,060 112,797 112,462 111,270 110,670 M115x3 H 115,000 ----- 113,051 ----- 111,752 M115x2 H 115,000 ----- 113,701 ----- 112,835 6H 115,000 113,951 113,701 113,210 112,835 6G6H 115,038 113,989 113,739 113,210 112,835 M120x6 H 120,000 ----- 116,103 ----- 113,505 M120x4 H 120,000 ----- 117,402 ----- 115,670 6H 120,000 117,737 117,402 116,270 115,670 6G6H 120,060 117,797 117,462 116,270 115,670 M120x3 H 120,000 ----- 118,051 ----- 116,752 M120x2 H 120,000 ----- 118,701 ----- 117,835 6H 120,000 118,951 118,701 118,210 117,835 6G6H 120,038 118,989 118,739 118,210 117,835 M125x6 H 125,000 ----- 121,103 ----- 118,505 M125x4 H 125,000 ----- 122,402 ----- 120,670 6H 125,000 122,737 122,402 121,270 120,670 6G6H 125,060 122,797 122,462 121,270 120,670 M125x3 H 125,000 ----- 123,051 ----- 121,752 M125x2 H 125,000 ----- 123,701 ----- 122,835 6H 125,000 123,951 123,701 123,210 122,835 6G6H 125,038 123,989 123,739 123,210 122,835 M144x4 H 144,000 ----- 141,402 ----- 139,670 6H 144,000 141,737 141,402 140,270 139,670 M148x2 H 148,000 ----- 146,701 ----- 145,835 6H 148,000 146,951 146,701 146,210 145,835 M171x2 H 171,000 ----- 169,701 ----- 168,835 6H 171,000 169,951 169,701 169,210 168,835 6G6H 171,038 169,989 169,739 169,210 168,835 M183x2 H 183,000 ----- 181,701 ----- 180,835 6H 183,000 181,965 181,701 181,210 180,835

Date post:	03-Feb-2018
Category:	Documents
Upload:	nguyenhuong
View:	378 times
Download:	11 times

Standard VCS 5081 159 - ePoptávka.cz · PDF fileStandard VCS 5081,159 Issue 1 Page 2...

Documents