1 hrs

1 pcs f

0.20 mmk

0.40 mmh PLA

15 g d

MK3/S

SummaryYou can glue a 10 x 1.5 mm round magnet in the base.

Art & Design > 2D Plates & Logos

yoda xwing trooper tie starbird solo sith royal republic ren rebellion r2d2 porg phasma phase order mythosaur maul mandalorian lord kylo jedi han guard first fighter fett emperor death darth clone chewbacca c3po boba alliance luke leia rebels palpatine empire galactic stormtrooper wars vader star

Recommended infill angle: 0°

Low speed and high temperature will create a shiny top surface.

There are "holes" inside the model to make some of the top layers moreuniform, and they were created with 0.2 layer height in mind.

Synth3D

Star Wars X-WingFighter Magnet

VIEW IN BROWSER

updated 14. 6. 2019 | published 12. 4. 2019

https://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/social/106/printshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnethttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnethttps://www.prusaprinters.org/prints?categoryId=13https://www.prusaprinters.org/prints?categoryId=16##########################################################################################

Print Files (.gcode) DOWNLOAD ALL FILES

2.1 MB

1.23 hrs f 0.20 mm k 0.40 mm h PLA 15.00 g d MK3/S updated 14. 4. 2019

Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES

1.4 MBupdated 14. 4. 2019

If your top surface is not flat & shiny and you see scarring, then make sureto check this guide: https://bit.ly/2UtN0I1

License This work is licensed under a Creative Commons (4.0 International License)

Attribution—Noncommercial—Share Alike

✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition

x-wing.gcode

x-wing.stl

https://bit.ly/2UtN0I1https://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttps://www.prusaprinters.org/prints/658-star-wars-x-wing-fighter-magnet/fileshttp://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/http://creativecommons.org/licenses/by-nc-sa/4.0/

Star Wars X-Wing Fighter MagnetSummaryPrint Files (.gcode)x-wing.gcode

Model Files (.stl, .3mf, .obj, .amf)x-wing.stl

LicenseAttribution—Noncommercial—Share Alike