+ All Categories
Home > Documents > START HERE. . . read all instructions before using · read all instructions before using. Created...

START HERE. . . read all instructions before using · read all instructions before using. Created...

Date post: 20-Jun-2020
Category:
Upload: others
View: 1 times
Download: 0 times
Share this document with a friend
1
2 START HERE. . . Verify contents; inspect for damage. A - (4) Legs B - Remote Control C - (3) AAA Batteries D - 4-Port Charging Hub (S-cape™ 2.0 Plus only) E - Power Down Device (batteries not included) F - Owners Manual G - Warranty Activation Card H - Mattress Retainer (cut zip-tie to remove) 5 4 PLUG ELECTRICAL POWER CORD INTO A WORKING, GROUNDED ELECTRICAL OUTLET. Note: An electrical surge protection device is recommended (not included). INSTALL BATTERIES IN REMOTE CONTROL (3-AAA SIZE, INCLUDED). ROTATE BASE OVER SO IT IS RESTING ON ITS LEGS. Note: S- cape ® + 2.0 base includes a 4-port charging hub at head end of base. AT LEAST TWO PEOPLE ARE RECOMMENDED FOR HANDLING AND MOVING ADJUSTABLE BASE. WARNING WARNING Install mattress to complete setup. If adjustable base will not operate, refer to the Troubleshooting Guide or detailed instructions in the owners manual. 3 Place mattress retainer ends into grommeted holes in top surface of base. Press down until horizontal retainer section is flush against base. MATTRESS RETAINER H A G B F OPTIONAL: INSTALL MATTRESS RETAINER. Mattress is equipped with a Micro-Hook™ system to captivate the mattress, but if desired a mattress retainer can also be used. NATIONWIDE CUSTOMER SERVICE toll free: (800) 888-3078 291-0007-b EDR13XXX 1/17 © 2017 Leggett & Platt Adjustable Bed Group, a division of Leggett & Platt, Incorporated LPAdjustableBases.com HEAD END OF BASE 4-PORT CHARGING HUB (S·cape ® + 2.0 base only) (located on each side of base, for charging low-voltage devices only; hub is free-standing on Split Queen bases) 1 EXTEND POWER CORD OUT HEAD END OF BASE. Note: Power cords must not interfere with any adjustable base mechanisms. Do not weave cords through base structure. REMOVE HARDWARE BOX. CUT ZIP-TIE AND REMOVE MATTRESS RETAINER. SCREW LEGS INTO BASE FRAME. LEG PUSH PIN IN TO ADJUST LEG HEIGHT (6 INCHES TO 10 INCHES) OPERATE REMOTE CONTROL TO VERIFY BASE FUNCTIONS PROPERLY. DISENGAGE LATCH ON BATTERY COMPARTMENT DOOR AND LIFT UP TO REMOVE. INSERT TABS IN TAB SLOTS AND SNAP LATCH IN TO REPLACE. DOOR LATCH BATTERY COMPARTMENT DOOR C D E QUICK SETUP GUIDE S-cape ® 2.0 / S-cape ® + 2.0 / Simplicity 3.0 n G-122 NWH n G-122 n G-122 NWH READ ALL INSTRUCTIONS BEFORE USING
Transcript
Page 1: START HERE. . . read all instructions before using · read all instructions before using. Created Date: 1/5/2017 8:35:38 AM ...

2

START HERE. . .Verify contents; inspect for damage.

A - (4) LegsB - Remote ControlC - (3) AAA BatteriesD - 4-Port Charging Hub (S-cape™ 2.0 Plus only)E - Power Down Device (batteries not included)F - Owners ManualG - Warranty Activation CardH - Mattress Retainer (cut zip-tie to remove)

54

PLuG ELECtRiCAL POWER CORD intO A WORkinG, GROunDED ELECtRiCAL OutLEt. Note: An electrical surge protection device is recommended (not included).

instALL BAttERiEs in REMOtE COntROL (3-AAA sizE, inCLuDED).

ROtAtE BAsE OVER sO it is REstinG On its LEGs.

Note: S-cape®+ 2.0 base includes a 4-port charging hub at head end of base.

at least two people are recommended for handling and

moving adjustable base.

WARNINGWARNING

install mattress to complete setup.

if adjustable base will not operate, refer to the troubleshooting Guide or detailed instructions in the owners manual.

3

Place mattress retainer ends into grommeted holes in top surface of base. Press down until horizontal retainer section is flush against base.

mattressretainer

h

a

g

b

f

OPtiOnAL: instALL MAttREss REtAinER. Mattress is equipped with a Micro-Hook™ system to captivate the mattress, but if desired a mattress retainer can also be used.

NATIONWIDE CUSTOMER SERVICE toll free: (800) 888-3078

291-0007-b EDR13XXX 1/17 © 2017 Leggett & Platt Adjustable Bed Group, a division of Leggett & Platt, incorporated

LPAdjustableBases.com

head end of base

4-port charging hub (s·cape®+ 2.0 base only) (located on each side of base, for charging low-voltage devices only; hub is free-standing on split Queen bases)

1EXtEnD POWER CORD Out HEAD EnD OF BAsE. Note: Power cords must not interfere with any adjustable base mechanisms. Do not weave cords through base structure.

REMOVE HARDWARE BOX. Cut ziP-tiE AnD REMOVE MAttREss REtAinER.

sCREW LEGs intO BAsE FRAME.

leg

push pin in to adjust leg height

(6 inches to 10 inches)

OPERAtE REMOtE COntROL tO VERiFy BAsE FunCtiOns PROPERLy.

disengage latch on battery compartment door and lift up to remove. insert tabs in tab slots and snap latch in to replace.

door latch

battery compartment door

c

d

e

QUICK SETUP GUIDE s-cape® 2.0 / s-cape®+ 2.0 / Simplicity™ 3.0nG-122 nWH nG-122 nG-122 nWH

read all instructions before using

Recommended