STATEMENT OF
RODNEY J. BOSCO
NAVIGANT CONSULTING, INC.
ON THE
“THE FUTURE OF MONEY: COIN PRODUCTION”
BEFORE THE
HOUSE FINANCIAL SERVICES SUBCOMMITTEE
ON DOMESTIC MONETARY POLICY & TECHNOLOGY
UNITED STATES HOUSE OF REPRESENTATIVES
APRIL 17, 2012
- 2 -
Mr. Chairman and Members of the Subcommittee, my name is Rodney Bosco and I am a
Director in the Disputes and Investigations practice at Navigant Consulting, Inc. (“Navigant”).
I am pleased to testify today concerning our coin system, its cost drivers, and an analysis we
conducted recently that identified approximately $200 million in annual cost savings if the
United States moved to a steel‐based composition for our vended nickel, dime, and quarter.
Navigant is an international consulting firm that provides independent, objective analysis of
and opinions on accounting, financial and economic issues. Our report was commissioned by
Jarden Zinc Products, North America’s leading plated coin blank producer and a licensee of
the Royal Canadian Mint’s multi‐ply plated steel technology. We acknowledge the
significant assistance of the Royal Canadian Mint (“RCM”) and Worthington Industries in
the preparation of our analysis.
As the Subcommittee examines ways to make our coins less expensively, and awaits the
United States Mint’s recommendations on alternative metals later this year, our work has
led us to three major conclusions which I want to share with you today.
(1) Adoption of a multi‐ply plated steel composition for the vended five‐cent, dime and
quarter‐dollar coins will reduce the per‐unit raw material costs of these coins by 84%
to 89%, based on recent prices of copper, nickel and low‐carbon steel during the
United States Mint’s 2011 fiscal year. Applied to average historical production of
these denominations, raw material cost savings on an annual basis would be
approximately $200 million.
(2) Parallel adoption of an alloy recovery program – in which the United States Mint
collects and replaces copper‐nickel alloy coins in circulation with multi‐ply plated
steel coins and salvages the copper and nickel material from the retired coins – has
the potential to generate over $2 billion in additional revenue for the United States
Mint.
(3) Losses reported by the United States Mint associated with penny production have
led some to suggest retiring the penny as a means of eliminating such losses. We
have found that ending production of the penny would not completely eliminate the
losses, as a portion of the United States Mint’s fabrication, distribution, and selling,
general and administrative (“SG&A”) costs assigned to the penny are fixed and will
continue to be incurred. Indeed, the United States Mint’s total losses from circulating
coin production could worsen from current levels depending on the extent to which
elimination of the penny increased demand for the nickel, which is also currently
produced at a loss.
- 3 -
These findings, which are discussed in more detail below, provide insights into the policy
and economic issues associated with United States Mint coin production.
1. RAW MATERIAL COST SAVINGS FROM CONVERTING UNITED STATES
VENDED COINAGE TO MULTI‐PLY PLATED STEEL
Navigant examined the potential raw material cost savings the United States Mint could
achieve through the substitution of copper‐ and nickel‐coated steel blanks for the
compositions currently in use. Multi‐ply plated steel compositions have been successfully
used by the RCM to manufacture circulating coinage for Canada, as well as for more than
two dozen nations, for over a decade.
A. The Royal Canadian Mint’s Experience with Transitioning from Alloy‐based Coins to
Multi‐Ply Plated Steel Coins
Prior to 2000, the RCM’s circulating coins were comparable to current United States coins in
that they were made from copper and nickel (see Figure 1). However, Canadian circulation
coins now employ a less costly primary material – low carbon steel.1 The changes made by
the RCM, including financing costs related to new fabrication techniques, have resulted in
significantly lower unit production costs across all denominations.
Figure 1: Base Metal Content of Circulating Coins in Canada (1982‐1999) and the United
States (current) 2
Five‐ Quarter‐
Canada (1982‐1999) Cent Dime Dollar
Copper 75.00% 0.00% 0.00%
Nickel 25.00% 99.90% 99.90%
Total 100.00% 99.90% 99.90%
Five‐ Quarter‐
United States (current) Cent Dime Dollar
Copper 75.00% 91.67% 91.67%
Nickel 25.00% 8.33% 8.33%
Total 100.00% 100.00% 100.00%
- 4 -
Since 2000, only 6% of each coin is comprised of semi‐precious metals, applied in a 3‐ply
layered fashion to an all‐steel core using an electroplating process.3 The RCM can alter the
order and “recipe” of each layer of copper, nickel, bronze or brass to adjust the coin’s color
and Electronic Magnetic Signal (used by coin acceptors to discriminate coins inserted into
their machines).4 Testing performed on the coins and reported by the RCM has found them
to exhibit other desirable characteristics with regard to wear, durability and appearance.5
According to the RCM, the changes made to the production of its circulating coinage saves
Canadians $10 million per year on production volumes of approximately 350 million coins.
In addition to producing circulating coins for Canada, the RCM sells circulating coins and
blanks utilizing its multi‐ply plating process to foreign countries. Since its introduction, 27
countries in addition to Canada have accepted this technology for their coinage needs.6
B. Raw Material Cost Savings From Converting United States Vended Coinage to Multi‐
Ply Plated Steel
Figure 2 compares the per‐unit raw material costs of producing each United States vended
coin using the United States Mint’s current composition and using the RCM’s multi‐ply
plated steel compositions. The potential savings, represented as the difference between the
two sets of figures, are substantial — at least 84% for each denomination. For a detailed
analysis of the derivation of the per‐unit raw material costs under each composition, refer
to Section III of our February 6, 2012 report.
Figure 2: Potential Per‐Unit Raw Material Cost Savings from Converting United States
Circulating Coins to Multi‐ply Plated Steel, Fiscal Year 2011 7
Quarter‐
Five‐Cent Dime Dollar
Current Composition 0.0644$ 0.0235$ 0.0587$
RCM Composition 0.0068 0.0037 0.0081
Savings (dollars) 0.0576$ 0.0198$ 0.0506$
Savings (percent) 89% 84% 86%
- 5 -
In order to estimate the total savings to the United State Mint assuming the per‐unit raw
material cost savings above, we determined the average production levels of vended coins
over the 30‐year period 1982‐2011. Applying the per‐unit cost savings under the alternative
composition scenario (as set forth in Figure 2) to each coin’s average production level, we
calculate the aggregate dollar value of raw material cost savings on an annual basis to be
$207.5 million (see Figure 3).
Figure 3: Potential Annual Raw Material Cost Savings from Converting United States
Vended Coins to Multi‐ply Plated Steel 8
Average
Production Per Unit Total
(A) × (B)
(A) (B) (C)
Mean:
Five‐Cent 1,194,895,000 0.0576$ 68,825,952$
Dime 1,962,359,000 0.0198$ 38,854,708$
Quarter‐Dollar 1,972,734,000 0.0506$ 99,820,340$
Total 5,129,988,000 207,501,001$
Median:
Five‐Cent 1,214,160,000 0.0576$ 69,935,616$
Dime 1,982,193,000 0.0198$ 39,247,421$
Quarter‐Dollar 1,475,417,000 0.0506$ 74,656,100$
Total 4,671,770,000 183,839,138$
Cost Savings
To assess the sensitivity of the cost savings calculation (Figure 3), we prepared the analysis
in Figure 4 to show the material costs savings under several different price change
assumptions for both copper/nickel and steel. For purposes of this analysis, we used the
mean production level over the past 30 years.
- 6 -
Figure 4: Sensitivity of Annual Raw Material Cost Savings (in millions) to Movements in
Metal Prices 9
Decrease 20% Decrease 10% No Change Increase 10% Increase 20%
Decrease 20% $166.1 $188.2 $210.4 $232.6 $254.7
Price of Decrease 10% $164.7 $186.9 $209.0 $231.2 $253.3
Steel No change $163.3 $185.5 $207.5 $229.8 $251.9
Increase 10% $161.9 $184.1 $206.2 $228.4 $250.5
Increase 20% $160.5 $182.7 $204.8 $227.0 $249.1
Prices of Copper and Nickel
To assess the sensitivity of the average (mean) production level to the inclusion of
particular years we also calculated the median production level of each coin during the
benchmark period. The mean and median production levels for the five‐cent coin and dime
were not significantly different.10 However, median production for the quarter‐dollar over
the 30‐year benchmark period was significantly less than mean production.11 As shown in
Figure 3, the savings based on median historical production is $183.8 million.
C. Options for the United States Mint to Consider in Changing its Vended Coins to Multi‐ply Plated Steel Compositions
As discussed above, the United States Mint can achieve significant cost savings related to its
production of vended coins by changing each coin’s composition from copper‐nickel alloys
to multi‐ply plated steel. While base metal costs make up the largest portion of production
costs,12 the United States Mint would incur new or additional costs in other parts of its
production process in order to implement this change. With the exception of the one‐cent
coin, we understand the United States Mint operates as a fully‐integrated manufacturing
operation, handling all aspects of the production process from receiving raw material
through the coining of the final product.
We have identified three production options for the United States Mint to consider if it
were to change its coin compositions from the current clad‐ and alloy‐based compositions
to multi‐ply plated steel coins – (1) continue to perform all production operations in‐house;
(2) purchase “ready‐to‐strike” blanks of plated steel coins, similar to the process currently
employed with the copper‐plated zinc penny; or (3) outsource the plating function but keep
all other operations in‐house.
Given the lack of publicly available data on the detailed operating costs of the United States
Mint’s operations in general, and coin plating facility operations specifically, we did not
- 7 -
evaluate the relative merits of the options based on expected costs. Rather, we include in
our February 6, 2012 report a discussion of the issues, including machinery and equipment,
facilities, employees, technology licensing, and production disruptions, which would need
to be addressed by the United States Mint in evaluating each option.
2. POTENTIAL ADDITIONAL REVENUE TO THE UNITED STATES MINT FROM
IMPLEMENTING AN ALLOY RECOVERY PROGRAM
Since its launch of multi‐ply plated steel circulation coins, the RCM has implemented an
alloy recovery program that has generated more than $200 million in revenue between 2004
and 2010. The United States Mint could execute a similar program for its current copper
and nickel‐based five‐cent, dime and quarter‐dollar coins. It was beyond the scope of our
study to estimate with precision the amount of revenue the United States Mint could expect
to receive from launching such a program. However, to provide insight into the potential
revenue opportunity we present a scenario based on publicly available information and
reasonable assumptions.
In Figure 2 we report the raw material cost associated with the five‐cent ($0.0644), dime
($0.0235) and quarter‐dollar ($0.0587) coins during fiscal year 2011. The average annual
production of each coin over the period 1982 through 2011 is presented in Figure 3.
Combining these two sets of information results in a reasonable measure of the revenue, on
a per‐coin basis, that the United States Mint could receive from retrieving, extracting and
selling the copper and nickel material through an alloy recovery program ($0.0466 per unit).
Our calculation, set forth in Figure 5, assumes that the shares of coins retrieved will mirror
their relative unit production quantities over the past 30 years.
Figure 5: Average Per‐Coin Raw Material Cost of Producing Five‐Cent, Dime and Quarter‐
Dollar Coins, Based on Fiscal Year 2011 Spot Prices 13
Average
Production Per Unit Total
(A) × (B)
(A) (B) (C)
Five‐Cent 1,194,895,000 0.0644$ 76,949,541$
Dime 1,962,359,000 0.0235$ 46,120,080$
Quarter‐Dollar 1,972,734,000 0.0587$ 115,894,896$
Total 5,129,988,000 238,964,517$
Average material cost per coin minted 0.0466$
Material Cost
- 8 -
The actual number of coins reclaimed through an alloy recovery program will depend on
the United States Mint’s ability to access inventories of circulating coins under the control of
(a) the Federal Reserve Banks and (b) private coin recycling companies, as well as the
effectiveness of campaigns designed to encourage the redemption of coin holdings
removed from circulation. Between 1982 and 2011, 153.9 billion five‐cent, dime and
quarter‐dollar coins were produced (equal to average annual unit coin production of 5.130
billion, as shown in Figure 5, multiplied by 30 years). If one‐third of these coins were
recovered through an alloy recovery program, the United States Mint’s additional revenue
could be $2.4 billion (equal to 51.3 billion coins multiplied by $0.0466). This calculation
assumes that current material prices do not significantly change.
The United States Mint would incur costs to implement and run an alloy recovery program,
including the possible production of replacement coins out of multi‐ply plated steel.
Consistent with our assessment of the costs to change from the current composition of
vended coins to multi‐ply plated steel composition, the United States Mint would be in the
best position to determine the costs to implement such a program. Assuming it is patterned
after the RCM’s program, one would expect that the United States Mint would also earn high
margins.
3. IMPACT OF ELIMINATING THE PENNY ON UNITED STATES MINT COSTS AND
PROFIT
In a separate report dated April 12, 2012, Navigant was asked to estimate the impact of
eliminating production of circulating pennies on losses currently being incurred by the United
States Mint. We have found that ending production of the penny would not completely
eliminate the losses, and could even increase the overall loss to the United States Mint due to
increased production of the nickel and ongoing United States Mint overhead costs.
The United States Mint shipped 4.29 billion pennies (valued at $42.9 million) during fiscal year
2011 at a reported cost of $103.1 million (2.4 cents per coin), resulting in a net loss of $60.2
million. However, eliminating production of the penny would not eliminate this loss, and
could even increase the overall loss to the United States Mint if production of the nickel was
increased to substitute for no production of the penny.
We analyzed publicly available information on the United States Mint’s past and projected
operations to identify patterns in costs related to its product offerings. We observed the
following:
- 9 -
Cost reductions from eliminating the purchase of penny blanks will be largely offset by
the loss of revenue from shipments to the Federal Reserve Banks (FRB). In other words,
the payments received from the FRB ($42.9 million), which offset all but $4.3 million of
the cost of penny blanks ($47.2 million), would not be received if the United States Mint
eliminated production of the penny.
The United States Mint’s fabrication and distribution costs include fixed components
that will continue to be incurred if the United States Mint eliminated the penny. Using
FY 2011 balances and prior United States Mint disclosures, we have estimated this fixed
component to be approximately $13 million.
The United States Mint’s total SG&A expense is not sensitive to circulating coin demand
or total sales. Thus, the $17.7 million in SG&A assigned to the circulating penny in FY
2011would have been reallocated to other products.
Substitution of loss‐generating nickels will offset potential cost reductions from
eliminating the penny.
Without the penny, only $4.3 million in net cost reductions would have been likely in 2011,
while an additional $25.2 million in cost reductions would have been possible, based on 2006
comments by the Mint regarding the amount of fixed production costs. However, the
substitution of nickels for pennies would have resulted in an increased net loss to the Mint of as
much as $10.9 million if penny production were not maintained. Our findings are summarized
in Figure 6.
Figure 6: Impact of Eliminating the Penny on the United States Mint’s FY 2011 Costs and
Profit (millions)
Yes No(Actual) (Estimate)
Value of Shipments 42.9$ ‐$
Gross Cost
Cost of Goods Sold (purchase of penny blanks) (47.2)$ ‐$
Cost of Goods Sold (fabrication and distribution) (38.2)$ (13.0)$
Sales, General and Administrative (SG&A) (17.7)$ (17.7)$
Profit (loss) before substitution effect (60.2)$ (30.7)$
Substitution of 914 million Nickels for 4.3 billion Pennies (40.4)$
Profit (loss) after substitution effect (71.1)$
Penny produced?
- 10 -
A. Cost Reductions from Eliminating the Purchase of Penny Blanks Will be Largely
Offset by Revenue Losses from Shipments to the Federal Reserve Banks
The United States Mint purchases ready‐to‐strike penny blanks from an outside supplier. In FY
2011, the average price paid was 1.1 cents per blank, according to one press report.14 The United
States Mint shipped 4.29 billion pennies to the FRB in FY 2011,15 resulting in a cost of $47.2
million. Had the penny not been produced, those costs would not have been incurred.
The value of coins shipped to the FRB is revenue to the United States Mint. Thus, the value of
the 4.29 billion pennies shipped to the FRB in FY 2011 was $42.9 million.16 Had the penny not
been produced, those revenues would not have been received.
The net reduction in cost had the penny not been produced in FY 2011 is equal to $47.2 million
in cost less $42.9 million in revenue, or $4.3 million.
B. The United States Mint’s Fabrication and Distribution Costs Include Fixed
Components that Will Continue to be Incurred if the United States Mint Eliminated
the Penny
Cost of Goods Sold, which comprise costs to fabricate and distribute coins, include outlays that
do not decrease with reductions in production volume. In fact, the United States Mint itself has
described in past Annual Reports how “fixed production costs” are spread over units produced:
“When production volumes decline because of lower demand, fixed production costs
are spread over fewer units. This offsets any per‐unit gains from lower base metal costs.
For example, the per‐unit metal cost of a nickel fell about $0.0154 from $0.0815 in FY
2007 to $0.0661 in FY 2008. However, the per‐unit fixed production costs increased
$0.0082, resulting in only a small decline in the nickel overall unit cost. Similarly, the
penny unit cost fell slightly from FY 2007 because of higher per‐unit vendor fabrication
costs offset lower per‐unit metal costs. The unit costs for dime and quarter
denominations increased in FY 2008 because of higher per‐unit fixed production costs.”17
“When production volumes decline because of lower demand, production costs are
spread over fewer units….The dime coin unit cost increased about 1.3 cents in FY 2009
largely because the 1.8 cent increase in per‐unit production cost offset the 1.0 cent
reduction in per‐unit metal cost….Slight increases in per‐unit production and SG&A
costs did not offset the 3.1 cent decline in the five‐cent coin’s per‐unit metal cost.”18
- 11 -
The United States Mint has acknowledged that a portion of penny production costs are also
fixed. In response to a question posed in a 2006 Congressional hearing, the United States Mint
responded as follows:
“Question: Do you have the ability to calculate how much the Mint would lose
if we were to eliminate the penny and make more nickels?
Answer: …the fixed costs associated with production of the penny would have
to be absorbed by the remaining denominations of circulating coins. The total
amount of fixed costs to be absorbed would be approximately $10.1 million over
a fiscal year of production.”19
The United States Mint’s commentary can be seen graphically in Figure 7 (for the penny) and
Figure 8 (for the nickel, dime and quarter), which compares shipments and per‐unit non‐raw
material costs from FY 2002 through FY 2011. The lines cross at FY 2007, the year before the
onset of the demand declines discussed by the Mint.20 Shipments and per‐unit costs diverge
after FY 2007,21 confirming the existence of fixed costs in the production process.
Figure 7: Coins Shipped and Per‐Unit Non‐Raw Material Cost of Goods Sold,
Fiscal Years 2002‐2011 (Penny) 22
$0.000
$0.002
$0.004
$0.006
$0.008
$0.010
$0.012
$0.014
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Coin Shipments (Billions) Non‐Raw Material COGS (per coin)
- 12 -
Figure 8: Coins Shipped and Per‐Unit Non‐Raw Material Cost of Goods Sold,
Fiscal Years 2002‐2011 (Nickel, Dime and Quarter) 23
$0.000
$0.006
$0.012
$0.018
$0.024
$0.030
$0.036
$0.042
$0.048
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Coin Shipments (Billions) Non‐Raw Material COGS (per coin)
The United States Mint has not reported the fixed costs incurred in FY 2011 to produce the
penny. However, insight may be gleaned by linking Mr. Lebryk’s statement above to the
United States Mint’s costs at that time. In FY 2005 and FY 2006, non‐raw material costs
associated with the penny were $46.5 million and $45.2 million, respectively.24 The $10.1 million
in fixed costs cited by Mr. Lebryk represent 21.7% (FY 2005) and 22.3% (FY 2006) of the non‐raw
material costs, resulting in average fixed costs of 22% over the two years. We applied this
average to the non‐raw material costs of penny shipments incurred by the United States Mint in
FY 2011 ($59.3 million)25 and estimated fixed costs of $13.0 million for FY 2011 in the production
of the penny. As production of the penny in FY 2011 was significantly less than in either FY
2005 or FY 2006, it is possible that fixed costs as a percent of total non‐raw material costs in FY
2011 could be higher than we have calculated.
Cost of Goods Sold for penny shipments during FY 2011 was $85.4 million. Purchases of ready‐
to‐strike blanks totaled $47.2 million (see Section I), leaving $38.2 million as the amount
attributable to fabrication and distribution operations executed by the United States Mint. The
fixed cost analysis performed above suggests that potential fabrication and distribution cost
reductions from the United States Mint eliminating the penny would have been $25.2 million
($38.2 million less $13.0 million) in FY 2011.
- 13 -
C. The United States Mint’s Total SG&A Expense Is Not Sensitive to Circulating Coin
Demand or Total Sales
For FY 2011, the United States Mint assigned $17.7 million of SG&A expense to circulating
pennies, equal to 0.41 cents for each penny shipped.26 This was in stark contrast to prior years –
a total of $5.1 million in SG&A had been assigned to circulating penny production for the nine‐
year period FY 2002 through FY 2010.27
Since FY 2004, the United States Mint’s published financial statements do not report the
individual expense items and amounts included in SG&A. However, we examined historical
financial information reported by the United States Mint over the past decade (FY 2002 through
FY 2011) and found that total SG&A expense is not sensitive to either the amount of total sales
or the relative contributions of circulating and numismatic products.
Our findings are graphically depicted in Figures 9 and 10. In Figure 9 we compare SG&A to
total sales from all products – annual sales grew by more than 170 percent while SG&A expense
stayed relatively constant. In Figure 10 we compare SG&A to the distribution of total sales
among circulating coins (lower bars) and numismatic products (upper bars) – circulating coins
fell from 76% of total sales in 2002 to 16% in 2011 while SG&A stayed relatively constant.
Figure 9: Total SG&A Expense and Total Sales, Fiscal Years 2002‐2011 28
- 14 -
Figure 10: Total SG&A Expense and Composition of Sales, Fiscal Years 2002‐2011 29
In Figure 11 we compare total SG&A to the number of circulating coins shipped. While total
SG&A stayed relatively constant throughout the period, there were three years in which
circulating coin shipments fell by an amount comparable to the United States Mint’s current (FY
2011) volume of penny shipments (4.3 billion coins):
In FY 2003, relative to FY 2002, SG&A fell 2% while circulating coin shipments fell by 3.6
billion coins or 24%
In FY 2008, relative to FY 2007, SG&A rose 10% while circulating coin shipments fell by
4.0 billion coins or 29%
In FY 2009, relative to FY 2008, SG&A fell 7% while circulating coin shipments fell by 4.8
billion coins or 48%
- 15 -
Figure 11: Total SG&A Expense and Circulating Shipments, Fiscal Years 2002‐2011 30
$0
$50
$100
$150
$200
$250
0
5
10
15
20
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Circulating Coins ‐ Units Shipped (Billions) SG&A Expense ‐ Total (Millions)
We conclude that eliminating the penny would not generate significant reductions in the United
States Mint’s SG&A expenses. Instead, it would simply result in the United States Mint
reallocating SG&A expenses to other circulating coins and numismatic products.
D. Substitution of Nickels for Pennies Would Offset Potential Cost Reductions
In a House Subcommittee hearing held in July 2006, acting United States Mint director David
Lebryk was asked about the potential substitution effects that may occur if the penny were
eliminated – specifically, what additional losses would the United States Mint incur if more
nickels were demanded.31 The question was likely prompted by Mr. Lebryk’s statement that
current production costs for the nickel exceeded the coin’s face value.32 Mr. Lebryk responded
that the United States Mint was unable to model the potential substitution effect but
acknowledged the potential for such substitutions by presenting a graph displaying “estimates
of potential costs based on various scenarios.”33
A scenario posed by Mr. Lebryk in his response envisioned nickel production doubling.34 In FY
2011, the United States Mint shipped 914 million circulating nickels at an average Cost of Goods
Sold of $0.0942,35 resulting in a loss of $0.0442 ($0.0942 less $0.05) for each nickel shipped.36 If
Mr. Lebryk’s scenario were applied to FY 2011 cost and shipment data, the United States Mint
would have incurred a substitution‐related loss of $40.4 million (914 million × $0.0442). In
contrast, we have identified a total of $29.5 million in possible net cost reductions if penny
production had been eliminated. Thus, if Mr. Lebryk’s substitution scenario were to occur,
eliminating the penny would likely have resulted in increased net costs to the United States
Mint, relative to the current state, of $10.9 million.
4. SUMMARY AND CONCLUSION
The key findings of our overall work conducted to date are as follows:
By changing the compositions of the nickel, dime and quarter‐dollar coins from copper‐
nickel alloys to multi‐ply plated steel, the United States Mint would incur significantly
lower raw materials costs – approximately $200 million per year based on average
historical production levels. Multi‐ply plated steel compositions have been successfully
used by the Royal Canadian Mint to manufacture circulating coinage for Canada, as well
as for more than two dozen nations, for over a decade.
By implementing a parallel alloy recovery program that collects and replaces copper‐
nickel alloy coins in circulation with multi‐ply plated steel coins and salvages the copper
and nickel material from the retired coins, the United States Mint could earn over $2
billion in additional revenue based on modest recovery levels.
Elimination of the penny would not eliminate government losses since the United States
Mint’s fabrication, distribution, and SG&A costs include fixed components that will
continue to be incurred whether or not the United States Mint produces the penny.
Additionally, eliminating the penny could increase the overall loss to the United States
Mint if production of the nickel was increased to substitute for elimination of the
production of the penny.
1 “Technical Proposal on Multi-ply Technology by the Royal Canadian Mint,” Royal Canadian Mint, pp. 3, 9.
2 <http://www.mint.ca/store/mint/learn/5-cents-5300006>; <http://www.mint.ca/store/mint/learn/10-cents-5300008>; <http://www.mint.ca/store/mint /learn/25-cents-5300010>; and <http://www.usmint.gov /about_the_mint/?action=coin_specifications>.
3 Ibid, pp. 4-5.
4 Ibid, pp. 4 and 7.
5 Ibid, pp. 5-6.
6 Royal Canadian Mint, Annual Report 2010, p. 14.
7 Source: Rodney J. Bosco and Kevin M. Davis, “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 18 (Per Unit Cost Savings).
8 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 18 (Per-unit Cost Savings).
9 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 18 (Per-unit Cost Savings). The prices of copper, nickel and steel were adjusted from their fiscal year
- 17 -
2011 averages (“No Change”) by 10% or 20%, as noted in the column and row headings, for purposes of this sensitivity analysis.
10 Per “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 19 (Potential Raw Material Cost Savings), the mean and median values for the nickel and the dime differed by less than 2.0%.
11 Per “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 19(Potential Raw Material Cost Savings),, median production for the quarter was 25.2% less than mean production.
12 United States Mint, 2011 Annual Report, p. 10.
13 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and “Potential Benefit to the United States Mint from Changing the Metallic Content of its Vended Coins to Multi-Ply Plated Steel,” February 6, 2012, Figure 18 (Per-unit Cost Savings).
14 Chris Isidore, “Obama wants cheaper pennies and nickels,” CNNMoney.com, February 15, 2012.
15 United States Mint, 2011 Annual Report, page 11.
16 Id.
17 United States Mint, 2008 Annual Report, page 29.
18 United States Mint, 2009 Annual Report, page 30.
19 Coin and Currency Issues Before Congress: Can We Still Afford Money?, Hearing Before the Subcommittee on Domestic and International Monetary Policy, Trade and Technology of the Committee on Financial Services, U.S. House of Representatives, One Hundred Ninth Congress, Second Session, July 19, 2006.
20 Shipments in FY 2007 were lower than in FY 2006, but within the range of prior years.
21 The same pattern was observed, separately, for the nickel, the dime, and the quarter.
22 Source: Rodney J. Bosco and Kevin M. Davis, “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2012, Appendix A-1.
23 Source: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2102, Appendix A-2.
24 Source: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2012, Appendix A-1. FY 2005 was the last full fiscal year prior to Mr. Lebryk’s July 2006 testimony, which occurred during FY 2006.
25 Source: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2012, Appendix A-1.
26 United States Mint, 2011 Annual Report, page 11.
27 United States Mint, Annual Report, 2002 through 2011. In FY 2011 the United States Mint changed the method it uses to allocate SG&A expense among its products from a gross margin basis to a gross cost basis. (United States Mint, 2011 Annual Report, page 10)
28 Sources: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2102, Appendix B-1 (total sales) and Appendix B-2 (total SG&A expense).
29 Sources: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2012, Appendix B-1 (shares of total sales) and Appendix B-2 (total SG&A expense).
30 Sources: “Impact of Eliminating the Penny on the United States Mint’s Costs and Profit in Fiscal Year 2011,” April 12, 2012, Appendix B-1 (circulating coin shipments) and Appendix B-2 (total SG&A expense).
31 Coin and Currency Issues Before Congress: Can We Still Afford Money?
- 18 -
32 Testimony of David A. Lebryk, July 19, 2006.
33 Coin and Currency Issues Before Congress: Can We Still Afford Money?
34 Coin and Currency Issues Before Congress: Can We Still Afford Money?
35 United States Mint, 2011 Annual Report, page 11.
36 The Mint also assigned SG&A of $16.1 million, or $0.0176 per coin shipped, to the nickel. For the reasons set forth in Section III, we have assumed that increased demand for nickels will not result in additional SG&A expense.
POTENTIAL BENEFITS TO THE UNITED
STATES MINT FROM CHANGING THE
METALLIC CONTENT OF ITS VENDED
COINS TO MULTI‐PLY PLATED STEEL
PURSUANT TO “THE COIN MODERNIZATION, OVERSIGHT, AND CONTINUITY ACT OF 2010” (PUBLIC LAW 111‐302)
Rodney J. Bosco
Kevin M. Davis
February 6, 2012
Page 1
Abstract
Since 1792, the United States Mint has been responsible for the manufacture and
distribution of sufficient volumes of circulating coins to facilitate the nation’s daily
transactions of goods and services. The first American legal tender coins were made
from precious metals (gold and silver) and designed to establish their monetary
value based on the intrinsic value of the material contained in them. Apart from
periods of occasional material shortages, the United States Mint maintained the
intrinsic value standard for its circulating coinage into the 20th century.
Between 1933 and 1970 the United States transitioned its legal tender coinage from
precious metals to “semi‐precious” metals such as copper and nickel. The change to
a fiat money standard was intended to give the United States Mint greater supply
flexibility to meet the needs of a growing economy. It also allowed the United States
Mint to earn a profit (called “seigniorage”) on its production of circulating coins,
which is used by the United States government to reduce its requirement to borrow
money from the public to finance the national debt.
Between 2002 and 2006 prices for copper and nickel climbed more than fourfold. In
2006 the United States Mint disclosed that the cost of producing the five‐cent coin
exceeded the coin’s face value. In July 2007 the Secretary of the Treasury asked
Congress to enact legislation authorizing changes to the composition of circulating
coins. The “Coin Modernization, Oversight, and Continuity Act of 2010” authorized
the Secretary of the Treasury to conduct tests and solicit input from independent
research facilities and current or potential suppliers as to the use of alternative
metallic materials in circulating coins.
This study provides insights into the potential raw material cost savings the United
States Mint could achieve through the substitution of copper‐ and nickel‐coated steel
blanks for the compositions currently in use. Multi‐ply plated steel compositions
have been successfully used by the Royal Canadian Mint to manufacture circulating
coinage for Canada, as well as for more than two dozen nations, for over a decade.
Key findings of this study, based upon analyses conducted to date, include the
following:
(1) Adoption of a multi‐ply plated steel composition for the five‐cent, dime and
quarter‐dollar coins will reduce the per‐unit raw material costs of these coins
by 89% (five‐cent), 84% (dime) and 86% (quarter‐dollar), based on recent
prices of copper, nickel and low‐carbon steel.
Page 2
(2) Applied to long‐term average annual historical production of these
denominations, raw material cost savings on an annual basis range from
$183.8 million to $207.5 million, depending on the extent to which the United
States Mint continues its successful rotating design program for its circulating
quarter‐dollar coins.
(3) Parallel adoption of an alloy recovery program that collects and replaces
copper‐nickel alloy coins in circulation with multi‐ply plated steel coins and
salvages the copper and nickel material from the retired coins, has the
potential to generate over $2 billion in additional revenue for the United
States Mint.
Adoption of multi‐ply plated steel coin compositions by the United States Mint
could be handled through total in‐house production, out‐sourced production up to
the receipt of “ready‐to‐strike” planchets or a combination of these two options with
a third‐party handling the plating process. Given that detailed cost data for the
United States Mint’s current operations and for the operation of a coin plating
facility is not available for public inspection and analysis, our study does not include
an evaluation of the merits of the options based on expected net cost savings.
Rather, we include in our report a discussion of the issues — including machinery
and equipment, facilities, employees, technology licensing, and production
disruptions — that will need to be addressed by the United States Mint in evaluating
each option.
The adoption of multi‐ply plated steel compositions in vended coins may have
impacts on certain industries and/or organizations that rely on these coins to
conduct their activities. For example, when the Royal Canadian Mint planned the
release of its multi‐ply plated steel coins it worked closely with Canada’s vending
industry to address their concerns. The identification of industries and
organizations within the United States that may be impacted, and the related
impacts thereon, are beyond the scope of this report.
This report was commissioned by Jarden Zinc Products, North America’s leading
plated coin blank producer and licensee of the Royal Canadian Mint’s multi‐ply
plated steel technology. The authors also gratefully acknowledge the significant
contributions of the Royal Canadian Mint and Worthington Industries.
Page 3
Section I – Evolution of Metal Compositions Used in United States Vended
Coins
The United States Mint was established by an Act of Congress on April 2, 1792.1
Since 1793, the United States Mint has manufactured and distributed coins to
support the nation’s commerce (hereafter, “circulating coins”).2 The United States
Mint operates as a bureau within the Department of the Treasury.3 Regulations
pertaining to the coining of money, including circulating coins, are effectuated
through Acts of Congress.4
A. The First Circulating Coins Were Tied to an Intrinsic Value Standard
The Coinage Act of 1792 authorized the manufacture of coinage based on “dollars”5
or fractions thereof. Coins with a value in excess of one dollar were to be made of
gold, while coins with a value between one dollar and “one twentieth” of a dollar
were to be made of silver.6 The remaining coins – cents and half cents – were to be
made of copper,7 a semi‐precious metal. The dollar coin was defined to be “of the
value [in silver] of a Spanish milled dollar as the same is now current….”, while the
amount of silver in the lower denominations was set in proportion to their relative
currency value.8 Thus, the first United States legal tender coins were designed to tie
their monetary values to the “intrinsic value” of the precious metal contained in
them. While technically based on a silver standard, the Coinage Act of 1792 also
established a proportional value of silver to gold, by weight, of 15:1.9 This linking of
silver and gold values effectively placed the new United States legal tender coinage
on a bi‐metal standard.
A series of Congressional Acts during the mid 19th century moved United States
legal tender coinage from a bi‐metal standard to a gold standard. In 1834, Congress
changed the legal exchange ratio between silver and gold from 15:1 to 16:1.10 In
1849, Congress authorized production of a gold dollar coin.11 In 1853, the legal
tender status of sub‐dollar silver coins, previously unlimited, became limited to
obligations up to five dollars.12 In 1866, Congress authorized the United States Mint
to begin production of a new five‐cent coin comprised of an alloy of copper (75%)
and nickel (25%).13 The Coinage Act of 1873 ended production of the silver half‐
dime and the silver dollar, and ended the free coinage of silver (which allowed silver
producers to have their bullion coined); it also granted, for the first time, legal tender
status to non‐precious metal based coins.14 In 1874, the legal tender status of silver
dollars became restricted to obligations of up to five dollars.15 Collectively the Acts
served to demonetize silver, moving the United States to a de‐facto gold standard
for its monetary system. Despite these changes, most denominations of circulating
coins continued to be made from gold or silver.
Page 4
B. Transition of Coin Compositions from Gold/Silver to Copper/Nickel
A banking crisis during the early 1930s led Congress to enact legislation authorizing
the President to direct the withdrawal of gold, in all its tradable forms, from the
United States economy.16 On April 5, 1933, President Franklin D. Roosevelt issued
Executive Order 6102, which prohibited “the withdrawal and withholding of gold
coin, gold bullion or gold certificates from the recognized and customary channels of
trade.” It also directed persons to deliver their gold holdings to authorized agents of
the Federal Reserve System, where the holdings were exchanged for their equivalent
value in other currency. The United States Mint ceased production of circulating
gold coins in 1933.17
By the early 1960s, worldwide silver consumption was outpacing new silver
production.18 The resulting global shortage of the precious metal posed a long‐term
supply risk to the United States Mint regarding its ability to produce silver‐based
circulating coins. As a consequence, on June 3, 1965 President Lyndon Johnson
proposed to Congress to authorize the removal of silver from United States
circulating coins.19 The Coinage Act of 1965, signed into law by President Johnson
on July 23, 1965,20 directed the United States Mint to (a) remove silver from the dime
and quarter‐dollar coins and substitute a “clad” or layered composition of copper
and nickel, and (b) reduce the silver content of the half‐dollar coin from 90% to
40%.21 In 1971 silver was removed from the circulating half‐dollar coin, replaced
with the same clad composition as the dime and quarter‐dollar coins.22
By moving to semi‐precious metals as the basis for its circulating coinage, the value
of which was less than the face value of the coins, the United States Mint was able to
increase the amount of profit or “seigniorage”23 earned from its operations. The
seigniorage is used by the United States to reduce the amount of money it would
otherwise borrow from the public to finance the national debt.24
C. Semi‐Precious Metal Five‐Cent Coins Become Unprofitable to Produce
In 2002 prices for copper and nickel began to increase. Within five years, prices had
risen more than fourfold. The average price levels for each metal, expressed in
dollars and on an index basis (relative to fiscal year 2002), are shown in Figure 1.25
The five‐cent coin has been particularly hard hit by rising metal costs given its
composition of 75% copper and 25% nickel. During the United States Mint’s 2011
fiscal year (October 2010 through September 2011), the price of nickel was more than
twice that of copper. Figure 2 provides a graphical depiction of the surge in monthly
average prices of each metal during the period 2002 through 2011, relative to the
previous two decades. 26
Page 5
Figure 1: Annual Average Spot Price per Metric Ton for Copper and Nickel, Fiscal Years 2002-2011
Fiscal
Year
Average
Price
Index
(2002=100)
Average
Price
Index
(2002=100)
2002 1,528.99$ 100 6,278.13$ 100
2003 1,652.64 108 8,302.13 132
2004 2,605.25 170 13,408.09 214
2005 3,373.84 221 15,117.51 241
2006 6,039.99 395 19,068.39 304
2007 7,098.21 464 38,063.18 606
2008 7,786.78 509 25,720.37 410
2009 4,478.95 293 13,026.23 207
2010 7,043.74 461 20,292.75 323
2011 9,104.04 595 24,206.76 386
Copper Nickel
Figure 2: Monthly Average Spot Price per Metric Ton for Copper and Nickel, January 1980-September 2011
$‐
$2,000
$4,000
$6,000
$8,000
$10,000
$12,000
1980
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
2000
01
02
03
04
05
06
07
08
09
10
11
COPPER
$‐
$10,000
$20,000
$30,000
$40,000
$50,000
$60,000
1980
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
2000
01
02
03
04
05
06
07
08
09
10
11
NICKEL
Page 6
In the United States Mint’s 2006 Annual Report, director Edmund Moy noted that,
“…by the fourth quarter, steeply rising metal prices had pushed the cost of
manufacturing the one‐cent and 5‐cent coins above face value.”27 In its 2011 Annual
Report the United States Mint stated, “The unit cost for…[the] nickel denomination[]
remained above face value for the sixth consecutive fiscal year.”28 Financial data
from the United States Mint supporting these observations for the five‐cent coin are
provided in Figure 3 below.29
Figure 3: Unit Cost of Producing and Distributing Circulating Five-Cent Coins,
Fiscal Years 2006-2011 (in dollars)
2006 2007 2008 2009 2010 2011
Cost of Goods Sold 0.0592$ 0.0949$ 0.0877$ 0.0579$ 0.0916$ 0.0938$
Sales, General & Administrative 0.0001 ‐ ‐ 0.0014 ‐ 0.0176
Distribution to Federal Reserve Banks 0.0004 0.0004 0.0006 0.0010 0.0006 0.0004
Total Expenses 0.0597$ 0.0953$ 0.0883$ 0.0603$ 0.0922$ 0.1118$
On a gross shipment basis, the United States Mint has lost more than $171 million
over the past six years producing the five‐cent coin. (See Figure 4)30
Figure 4: Losses from Circulating Five-Cent Coins, Fiscal Years 2006-2011 (in
millions of dollars)
2006 2007 2008 2009 2010 2011 Total
Value of Shipments 72.6$ 64.4$ 32.3$ 10.3$ 17.9$ 45.7$ 243.2$
Cost of Goods Sold (87.1) (122.9) (57.1) (12.2) (33.1) (86.1) (398.5)
Sales, General & Administrative (0.1) ‐ ‐ (0.3) ‐ (16.1) (16.5)
Seigniorage (14.6)$ (58.5)$ (24.8)$ (2.2)$ (15.2)$ (56.5)$ (171.8)$
Rising material prices have also negatively impacted the seigniorage the United
States Mint earns on its shipments of dime and quarter‐dollar coins to the Federal
Reserve Banks. Between 2003 and 2011 such seigniorage has been reduced by more
than $577 million. This is shown in Figure 5 (dime) and Figure 6 (quarter‐dollar).31
Page 7
Figure 5: Reduction in Seigniorage from Circulating Dimes, Fiscal Years 2003-2011
Coins
Fiscal Shipped Reduction in
Year Actual 2002 Level Difference (millions) Seigniorage
(A) ‐ (B) (C) × (D)
(A) (B) (C) (D) (E)
2003 0.0050$ 0.0044$ 0.0006$ 1,888 1,207,576$
2004 0.0080 0.0044 0.0036 2,570 9,213,771
2005 0.0099 0.0044 0.0055 2,748 15,130,759
2006 0.0162 0.0044 0.0118 3,023 35,658,531
2007 0.0220 0.0044 0.0176 2,247 39,515,263
2008 0.0210 0.0044 0.0167 1,070 17,852,460
2009 0.0118 0.0044 0.0074 358 2,652,197
2010 0.0185 0.0044 0.0141 887 12,519,056
2011 0.0235 0.0044 0.0191 1,403 26,849,267
Total 160,598,880$
(spot price basis)
Raw Material Cost per Coin
Figure 6: Reduction in Seigniorage from Circulating Quarter-Dollars, Fiscal Years 2003-2011
Coins
Fiscal Shipped Reduction in
Year Actual 2002 Level Difference (millions) Seigniorage
(A) ‐ (B) (C) × (D)
(A) (B) (C) (D) (E)
2003 0.0125$ 0.0109$ 0.0016$ 2,442 3,902,473$
2004 0.0199 0.0109 0.0090 2,244 20,105,759
2005 0.0247 0.0109 0.0138 2,743 37,748,478
2006 0.0404 0.0109 0.0295 3,007 88,662,051
2007 0.0549 0.0109 0.0440 2,711 119,152,135
2008 0.0526 0.0109 0.0417 2,510 104,678,954
2009 0.0294 0.0109 0.0185 965 17,870,863
2010 0.0462 0.0109 0.0353 252 8,890,705
2011 0.0587 0.0109 0.0478 323 15,451,488
Total 416,462,905$
(spot price basis)
Raw Material Cost per Coin
Page 8
As depicted in Figure 2, prices of both metals declined between mid‐2007 and late
2008. However, since then copper prices have surged once more – exceeding the
2007 peak in seven of the past 10 months (as of September 2011).32 With copper
currently serving as the primary material in five‐cent (75.00%), dime (91.67%) and
quarter‐dollar (91.67%) coins,33 its procurement has become a significant non‐
controllable cost for the United States Mint. This was recognized by the United
States Mint in 2005, when it commenced a comprehensive coinage material study of
“cost effective alternative materials for circulating…coin denominations.”34 By 2010,
the United States Mint was calling for Congressional action to address this issue:
“Changing the composition of coins to less expensive alternative
materials could generate significant cost savings and mitigate further
reductions in seigniorage should metal market prices escalate…. The
compositions of five‐cent, dime, quarter‐dollar and half‐dollar coins
are codified by statute. Any authority to change the composition of
these denominations requires [Congressional action].”35
D. Congressional Consideration of Alternative Metal Compositions for
Circulating Coins
The United States Mint had been calling for legislative relief well before the
release of its 2010 Annual Report. On July 19, 2006, Acting Director David
Lebryk testified before the House Subcommittee on Domestic and International
Monetary Policy Trade and Technology. In his opening address Lebryk stated
that the United States Mint “look[ed] forward to working with Congress on this
issue [coin costs].”36 On July 30, 2007, the Secretary of the Treasury wrote a letter
to Congress seeking legislation to be enacted authorizing the Secretary of the
Treasury to make changes to the composition of circulating coins.37
Congress considered three bills to address the Secretary of the Treasury’s
request. The first two bills – the Coinage Materials Modernization Act of 2007 and the Coin Modernization and Taxpayer Savings Act of 2007 – proposed granting the Secretary of the Treasury broad authority to determine the weight and
composition of all circulating coinage.38 Neither bill made it out of committee.39
The third bill, the Coin Modernization and Taxpayer Savings Act of 2008, directed the United States Mint to adopt plated steel compositions for the one‐cent and
five‐cent coins but granted the Secretary of the Treasury the authority to modify
such compositions under certain conditions.40 Although passed by the House on
May 8, 2008, no major action was taken by the Senate.41
Page 9
On September 22, 2010, The Coin Modernization, Oversight, and Continuity Act of 2010 was introduced.42 This bill would authorize the Secretary of the Treasury to
conduct research and development on alternative metallic compositions for
United States circulating coinage but would not authorize the Secretary of the
Treasury to make any changes.43 The Secretary of the Treasury would also be
required to report to Congress on the United States Mint’s production costs, cost
trends and possible new metallic materials or technologies for the production of
circulating coins, as well as provide detailed recommendations for any proposed
content changes.44 The bill passed both houses of Congress and was signed into
law by President Barack Obama on December 14, 2010.45
Page 10
Section II – The Royal Canadian Mint’s Experience with Transitioning from
Alloy‐based Coins to Multi‐Ply Plated Steel Coins
In its 2005 Annual Report, the United States Mint noted that it was planning to
invest in a research and development program that would “explore new
manufacturing, metal fabrication and finishing techniques that will improve its
manufacturing operations….”46 As part of that effort, the United States Mint would
“explore what other mints are doing around the world.”47 In Section II we examine
the experience of the Royal Canadian Mint (“RCM”).
A. Material Cost Savings Achieved by Changing Coin Compositions
Prior to 2000 the RCM’s coin compositions were comparable to current United States
coin compositions in that they were made from copper and nickel (see Figure 7
below). However, Canadian circulation coins now employ a less costly primary
material. The composition changes made by the RCM, including financing costs
related to new fabrication techniques, have resulted in significantly lower unit
production costs across all denominations.
Figure 7: Base Metal Content of Circulating Coins in Canada (1982-1999) and the
United States (current) 48
Five‐ Quarter‐
Canada (1982‐1999) Cent Dime Dollar
Copper 75.00% 0.00% 0.00%
Nickel 25.00% 99.90% 99.90%
Total 100.00% 99.90% 99.90%
Five‐ Quarter‐
United States (current) Cent Dime Dollar
Copper 75.00% 91.67% 91.67%
Nickel 25.00% 8.33% 8.33%
Total 100.00% 100.00% 100.00%
In 2000, the RCM made a significant change to its circulating coinage, replacing most
of the copper and nickel with a low‐carbon steel alloy.49 Only 6% of each coin’s
composition is now comprised of semi‐precious metals – applied in a 3‐ply layered
fashion to the outside of an all‐steel core using an electroplating process.50 The RCM
can alter the order and “recipe” of each layer of copper, nickel, bronze or brass to
Page 11
adjust the coin’s color and Electronic Magnetic Signal (used by coin acceptors to
discriminate coins inserted into their machines).51 Testing performed on the coins
and reported by the RCM has found them to exhibit other desirable characteristics
with regard to wear, durability and appearance.52
According to the RCM, the changes made to the production of its circulating coinage
saves Canadians $10 million per year. A press release issued in October 2001 by the
RCM quantified annual production cost savings under an assumed average volume
of each denomination.53 In its 2000 Annual Report, the RCM disclosed annual debt
service payments related to its construction of a plating facility, which had a total
construction cost of $30.3 million.54 Using these sources we calculated a Net Annual
Savings of $10,575,602 (see Figure 8), consistent with the RCM’s claims.
Figure 8: Cost Comparison: Nickel Alloy vs. Multi-ply Plated Steel, Canadian
Circulating Coins
Projected
Annual
Coin Production Unit Cost Annual Cost Unit Cost Annual Cost Dollars Percent
(A) × (B) (A) × (D) (C) ‐ (E) (F) ÷ (C)
(A) (B) (C) (D) (E) (F) (G)
5‐cent 95,660,000 0.0360$ 3,443,760$ 0.0113$ 1,080,958$ 2,362,802$ 69%
10‐cent 141,800,000 0.0350$ 4,963,000$ 0.0070$ 992,600$ 3,970,400$ 80%
25‐cent 112,400,000 0.0910$ 10,228,400$ 0.0150$ 1,686,000$ 8,542,400$ 84%
Total 349,860,000 18,635,160$ 3,759,558$ 14,875,602$ 80%
Annual financing costs for plating facility:
Principal (3,100,000)$
Interest (1,200,000)$
Net Annual Savings 10,575,602$
Nickel Alloy Multi‐ply Plated Steel Cost Savings
In addition to producing circulating coins for Canada, the RCM sells circulating
coins and blanks utilizing its multi‐ply plating process to foreign countries. Since its
introduction, 27 countries in addition to Canada have accepted this technology for
their coinage needs.55 With sales of 1.1 billion coins and blanks in 2010, the RCM
had a 9.5% share of the foreign circulation coinage market.56
Page 12
B. Additional Revenues from Reclaiming Old‐Composition Coins
Beginning in 2003, the RCM launched an Alloy Recovery Program (“ARP”).
Under the program, old‐composition coins are reclaimed from circulation and
melted, with the recovered alloy material sold to metal dealers at market prices.
The RCM replaces the reclaimed coins with new‐composition coins so that day‐
to‐day commercial transactions continue uninterrupted.57 Through 2010, the
RCM has received over $200 million in revenue from the ARP, as shown in
Figure 9 below.58 While the profit from such operations is not reported by the
RCM, it has been characterized as a “high‐margin” business.59
Figure 9: Revenue Earned by the Royal Canadian Mint from its Alloy Recovery
Program, 2004 – 2010
Year Revenue
2004 8.0$
2005 11.2
2006 19.4
2007 35.8
2008 55.4
2009 51.4
2010 22.6
Total 203.8$
Page 13
Section III – Raw Material Cost Savings from Converting United States
Vended Coinage to Multi‐ply Plated Steel
In this section we calculate the current raw material costs and the alternative raw
material costs associated with having the United States Mint adopt the RCM’s coin
compositions for the circulating five‐cent, dime and quarter‐dollar denominations.
We have examined the costs of each metal on a spot market basis; that is, the price
from the mine as recorded by a trading market such as the London Metal Exchange.
As such, the price does not include costs associated with processing, fabrication,
packaging and transport that would be performed by a vendor prior to the material
being received by the United States Mint. The time frame for our analysis is the
United States Mint’s most recently‐completed fiscal year, which ended on September
30, 2011.
As shown in Figure 7, the United States Mint currently uses copper and nickel for its
five‐cent, dime and quarter‐dollar coins. Using weight and composition data
published by the United States Mint, it is possible to determine, for each
denomination, the amount of each metal used to make a single coin. This is shown
in Figure 10.60
Figure 10: Material Inputs for United States Vended Coins on a Per-Unit Basis
(Current Composition)
Metal
Percent
of Total
Quantity
(grams)
Percent
of Total
Quantity
(grams)
Percent
of Total
Quantity
(grams)
(A) x 5.000 (C) x 2.268 (E) x 5.670
(A) (B) (C) (D) (E) (F)
Copper 75.00% 3.750 91.67% 2.079 91.67% 5.198
Nickel 25.00% 1.250 8.33% 0.189 8.33% 0.472
Total 5.000 2.268 5.670
Five‐Cent Dime Quarter‐Dollar
The United States Mint does not disclose the contract prices it pays for the flat rolled
coils of base metals used in the minting of its circulating coinage. However, in
recent Annual Reports the United States Mint has published charts that show spot
prices for copper and nickel over time and uses these charts to explain changes in its
production costs vis‐à‐vis prior years.61 Therefore, for purposes of our study, which
seeks to estimate potential material cost savings to the United States Mint through
the substitution of lower cost metals relative to its current costs, we believe spot
prices serve as a reliable proxy measure.
Page 14
Spot prices are published daily on a “per metric‐ton” (or 1,000 kilogram) basis; 62
market analysts also publish average prices on a weekly and monthly basis.63 The
United States Mint purchases material as needed throughout the year to satisfy
demand for circulating coins by the Federal Reserve Banks.64 Assuming that
purchases occur in a uniform manner throughout the year, we have calculated, for
copper and nickel, the average spot market price during fiscal year 2011 as the
average of the monthly‐average prices for October 2010 through September 2011.
These averages ($9,104 for copper; $24,207 for nickel) are shown in Figure 1.
In order to place the quantity and price data on the same scale, we divided the
quantities shown in Figure 9 by one million to obtain a per‐metric ton equivalent.
The product of quantity and price, summed across the two base metals, yields the
raw material cost, on a per‐unit basis, for each denomination. This is shown in
Figure 11.65 We note that the raw material cost for the five‐cent coin, $0.0644,
exceeds its face value.
Figure 11: Raw Material Cost for United States Vended Coins on a Per-Unit Basis, Fiscal Year 2011 (Current Composition)
Copper:
Weight (Metric Tons)
Price per Metric Ton
Total Copper Cost
Nickel:
Weight (Metric Tons)
Price per Metric Ton
Total Nickel Cost
Total Material Cost
Five‐Cent Dime Quarter‐Dollar
0.000003750 0.000002079 0.000005198
0.000001250 0.000000189 0.000000472
0.0644$ 0.0235$ 0.0587$
9,104.04$
0.0341$
24,206.76$
0.0303$
9,104.04$
0.0189$
9,104.04$
0.0473$
24,206.76$
0.0046$
24,206.76$
0.0114$
Having determined the per‐unit raw material costs under the United States Mint’s
current coinage compositions, we turn to the calculation of per‐unit raw material
costs under an alternative composition based on the RCM’s multi‐ply plated steel
compositions. In Figure 10 we determined the amount of copper and nickel
required to make a single unit of each denomination by multiplying the coin’s total
weight by each metal’s composition percentage – information published by the
United States Mint. However, while the composition percentages under the RCM’s
multi‐ply plated formulation are known, the total weights of the modified coins are
not known and must be calculated.
Page 15
Substituting steel for copper and nickel while maintaining each coin’s current
diameter and thickness will result in a lower weight, as steel is less dense than
copper and nickel. In order to determine how much lighter each RCM‐composition
United States coin will be, the volume of raw material used in each coin must be
calculated. The United States Mint’s published coin specifications do not include
volumes. However, given the total weight and metal composition of the current
coins, as well as the densities of each metal, the volume of each coin can be
estimated. This is shown in Figure 12.
Figure 12: Volume (in cubic centimeters) of United States Vended Coins 66
Material
Metal Density Weight Volume Weight Volume Weight Volume
(grams/cc) (grams) (cc) (grams) (cc) (grams) (cc)
(B) ÷ (A) (D) ÷ (A) (F) ÷ (A)
(A) (B) (C) (D) (E) (F) (G)
Copper 8.930 3.750 0.420 2.079 0.233 5.198 0.582
Nickel 8.880 1.250 0.141 0.189 0.021 0.472 0.053
Total 5.000 0.561 2.268 0.254 5.670 0.635
Five‐Cent Dime Quarter‐Dollar
Once the volumes of each coin are known, the weights of the RCM‐composition
United States coins can be determined. The calculations are shown in Figure 13
(five‐cent), Figure 14 (dime) and Figure 15 (quarter‐dollar). Note that for each
denomination the shares of the coin’s total weight (shown in column B) are per the
RCM’s specifications.
Figure 13: Weight of United States Circulating Five-Cent Coin Using RCM
Composition 67
Material Density
Share of
Weight
Average
Density Volume
Total
Weight
(grams/cc) (percent) (grams/cc) (cc) (grams)
(A) x (B) (C) x (D)(A) (B) (C) (D) (E)
Steel 7.872 94.50% 7.439
Copper 8.930 3.50% 0.313
Nickel 8.880 2.00% 0.178
100.00% 7.930 0.561 4.449
Page 16
Figure 14: Weight of United States Circulating Dime Using RCM Composition 68
Material Density
Share of
Weight
Average
Density Volume
Total
Weight
(grams/cc) (percent) (grams/cc) (cc) (grams)
(A) x (B) (C) x (D)(A) (B) (C) (D) (E)
Steel 7.872 92.00% 7.242
Copper 8.930 5.50% 0.491
Nickel 8.880 2.50% 0.222
100.00% 7.955 0.254 2.021
Figure 15: Weight of United States Circulating Quarter-Dollar Using RCM Composition 69
Material Density
Share of
Weight
Average
Density Volume
Total
Weight
(grams/cc) (percent) (grams/cc) (cc) (grams)
(A) x (B) (C) x (D)(A) (B) (C) (D) (E)
Steel 7.872 94.00% 7.400
Copper 8.930 3.80% 0.339
Nickel 8.880 2.20% 0.195
100.00% 7.934 0.635 5.038
Having determined the weights of the RCM‐Composition United States vended
coins, the amount of each metal that would be used to produce a single five‐cent
coin, dime and quarter‐dollar can be determined. This is shown in Figure 16.
Figure 16: Material Inputs for United States Vended Coins on a Per-Unit Basis (RCM Composition) 70
Metal
Percent
of Total
Quantity
(grams)
Percent
of Total
Quantity
(grams)
Percent
of Total
Quantity
(grams)
(A) x 4.449 (C) x 2.021 (E) x 5.038
(A) (B) (C) (D) (E) (F)
Copper 3.50% 0.156 5.50% 0.111 3.80% 0.191
Nickel 2.00% 0.089 2.50% 0.051 2.20% 0.111
Steel 94.50% 4.204 92.00% 1.859 94.00% 4.736
Total 4.449 2.021 5.038
Five‐Cent Dime Quarter‐Dollar
Page 17
Likewise, after converting the gram‐denominated material weights to their metric
ton equivalents, the cost associated with each material in each coin can be calculated
as the product of quantity and price. This is shown in Figure 17.
Figure 17: Raw Material Cost for United States Vended Coins on a Per-Unit Basis, Fiscal Year 2011 (RCM Composition) 71
Copper:
Weight (Metric Tons)
Price per Metric Ton
Total Copper Cost
Nickel:
Weight (Metric Tons)
Price per Metric Ton
Total Nickel Cost
Steel:
Weight (Metric Tons) Price per Metric Ton Total Steel Cost
Total Material Cost
0.0037$
0.000004204 0.000001859 0.000004736 774.00$ 774.00$ 774.00$
0.0081$ 0.0068$ 0.0037$
0.0033$ 0.0014$
24,206.76$ 24,206.76$ 24,206.76$
0.0022$ 0.0012$ 0.0027$
0.0014$ 0.0010$ 0.0017$
0.000000089 0.000000051 0.000000111
0.000000156 0.000000111 0.000000191
9,104.04$ 9,104.04$ 9,104.04$
Five‐Cent Dime Quarter‐Dollar
Figure 18 compares the per‐unit raw material costs of producing each United States
vended coin using the United States Mint’s current composition and using the
RCM’s multi‐ply plated steel compositions. The potential savings, represented as
the difference between the two sets of figures, are substantial — at least 84% for each
denomination. Additionally, the percentage figures are of the same order of
magnitude as those experienced by the RCM in 2000.72
Figure 18: Potential Per-Unit Raw Material Cost Savings from Converting United
States Circulating Coins to Multi-ply Plated Steel, Fiscal Year 2011 73
Quarter‐
Five‐Cent Dime Dollar
Current Composition 0.0644$ 0.0235$ 0.0587$
RCM Composition 0.0068 0.0037 0.0081
Savings (dollars) 0.0576$ 0.0198$ 0.0506$
Savings (percent) 89% 84% 86%
Page 18
As noted above, the RCM claims that the adoption of its multi‐ply plated steel
technology saves Canadians $10 million each year, based on a projected level of
domestic circulating coin production. The analysis set forth in Figure 8 provides an
overall savings estimate (including incremental capital costs) that is consistent with
the RCM’s claims. While we discuss certain “all in” net savings scenarios in Section
IV of this report, we conclude this section by examining, at a high level, the potential
raw material cost savings the United States Mint could earn each year by
substituting multi‐ply plated steel compositions for its current compositions.
Production levels of the five‐cent coin, dime and quarter‐dollar vary widely from
year to year. Between 1982 and 2011 production levels changed by less than 10% six
times, while changes of 20% or more occurred 19 times.74 From 1997 to 2000
production more than tripled to an all‐time high, followed by declines of 20‐29% in
each of the following three years.75 In 2009, production of five‐cent coins and dimes
fell to their lowest levels since 1955.76 Thus, our estimate of raw material cost
savings has been calculated, and should be viewed, as a long‐term average.
We used the 30‐year period 1982‐2011 as the benchmark for our calculation of
average production levels. Applying the per‐unit cost savings under the alternative
composition scenario (as set forth in Figure 18) to each coin’s average production
level, we calculate the aggregate dollar value of raw material cost savings on an
annual basis, which is equal to $207.5 million. This is shown in Figure 19 below.
Figure 19: Potential Annual Raw Material Cost Savings from Converting United States Vended Coins to Multi-ply Plated Steel 77
Average
Production Per Unit Total
(A) × (B)
(A) (B) (C)
Mean:
Five‐Cent 1,194,895,000 0.0576$ 68,825,952$
Dime 1,962,359,000 0.0198$ 38,854,708$
Quarter‐Dollar 1,972,734,000 0.0506$ 99,820,340$
Total 5,129,988,000 207,501,001$
Median:
Five‐Cent 1,214,160,000 0.0576$ 69,935,616$
Dime 1,982,193,000 0.0198$ 39,247,421$
Quarter‐Dollar 1,475,417,000 0.0506$ 74,656,100$
Total 4,671,770,000 183,839,138$
Cost Savings
Page 19
To assess the sensitivity of the cost savings calculation (Figure 19), we prepared the
analysis in Figure 20 to show the material costs savings under several different price
change assumptions for both copper/nickel and steel. For purposes of this analysis
we used the mean production level over the past 30 years. Figure 20: Sensitivity of Annual Raw Material Cost Savings to Movements in Metal
Prices 78
Decrease 20% Decrease 10% No Change Increase 10% Increase 20%
Decrease 20% $166.1 $188.2 $210.4 $232.6 $254.7
Price of Decrease 10% $164.7 $186.9 $209.0 $231.2 $253.3
Steel No change $163.3 $185.5 $207.5 $229.8 $251.9
Increase 10% $161.9 $184.1 $206.2 $228.4 $250.5
Increase 20% $160.5 $182.7 $204.8 $227.0 $249.1
Prices of Copper and Nickel
To assess the sensitivity of the average (mean) production level to the inclusion of
particular years we also calculated the median production level of each coin during
the benchmark period. The mean and median production levels for the five‐cent
coin and dime were not significantly different.79 However, median production for
the quarter‐dollar over the 30‐year benchmark period was significantly less than
mean production.80
The difference between the two measures of average for the quarter‐dollar is
attributable to the United States Mint’s successful quarter‐dollar rotating design
series. Beginning with the 50 State Quarters Program (1999‐2008) and followed by
the District of Columbia and U.S. Territories Program (2009) and the America the
Beautiful Quarters Program (2010‐present), the United States Mint has issued five or
six versions of the quarter‐dollar each year, differentiated by their reverse image.81
The interest these Programs have generated – the United States Mint estimates that
147 million Americans collected coins under the 50 State Quarters Program – has led
to significantly greater annual production relative to the pre‐1999 period.82 The
current Program, which will honor 56 national parks and sites, is scheduled to run
through 2021.83
By providing both mean and median measures of long‐term “average” production it
is possible to assess the impact of the United States Mint’s rotating design programs
on the potential raw material cost savings opportunity. The $207.5 million figure
portends continued administration of rotating design programs by the United States
Mint, while the $183.8 million figure is more consistent with an eventual return to a
single issue set of circulating coins each year.
Page 20
Section IV – Options for the United States Mint to Consider in Changing its
Vended Coins to Multi‐ply Plated Steel Compositions
As discussed in Section III, the United States Mint can achieve significant cost
savings related to its production of vended coins by changing each coin’s
composition from copper‐nickel alloys to multi‐ply plated steel. While base metal
costs make up the largest portion of production costs,84 the United States Mint
would incur new or additional costs in other parts of its production process in order
to implement this change. Notably, each of the United States Mint’s plants would
need to be modified to accept and integrate a coin plating facility. With the
exception of the one‐cent coin, we understand the United States Mint operates as a
fully‐integrated manufacturing operation, handling all aspects of the production
process from receiving raw material through the coining of the final product.
After consulting with industry experts, we have identified three production options
for the United States Mint to consider if it were to change its coin compositions from
the current clad‐ and alloy‐based compositions to multi‐ply plated steel coins:
Option 1 – Continue to perform all production operations in‐house;
Option 2 – Purchase “ready‐to‐strike” blanks of plated steel coins, similar to
the process currently employed with the copper‐plated zinc
penny; or
Option 3 – Outsource the plating function but keep all other operations in‐
house.
Given the lack of publicly available data on the detailed operating costs of the
United States Mint’s operations in general, and coin plating facility operations
specifically, we did not evaluate the relative merits of the options based on expected
costs. Rather, we include herein a discussion of the issues that would need to be
addressed by the United States Mint in evaluating each option. Given its extensive
institutional knowledge of its operational capabilities, along with its legacy of
designing and testing well over a thousand patterns and experimental and trial
pieces85 over the past two centuries, the United States Mint is in the best position to
determine cost estimates for each of the options and issues that we raise for
consideration.
Page 21
A. Option 1 – Continue to Perform all Production Operations In‐house
Currently, the United States Mint handles the production of its copper‐nickel alloy
based vended coins – from the receipt of flat rolled coils of metal through coining –
within its Philadelphia and Denver plants. If the United States Mint were to move to
producing multi‐ply plated steel coins, it would need to consider a number of cost
issues – including machinery and equipment, facilities, employees, and technology
licensing – as well as potential short‐term production disruptions. Each of these
issues is discussed below.
1. Machinery and equipment – The United States Mint would need to evaluate
what new and/or additional production capabilities would be needed. Coins
made from a steel core need to be plated after the blanking and plancheting
process, a task that is not currently performed by the United States Mint for
any of its vended coins. Additionally, the United States Mint would need to
evaluate which of its current production machinery and equipment (blanking
presses, annealers, upsetting mills, stamping presses, dies, etc.) could be
retooled to accept the new metallic compositions (and, if so, the implications
for each component’s useful life, run rate, and downtime for scheduled
maintenance) and which would need to be retired and replaced with new
equipment employing compliant technology.
2. Facilities – Once the machinery and equipment issues have been resolved, the
United States Mint would need to turn its attention to the adequacy of its
current facilities. Specifically, could the changes required to accommodate
the fully‐integrated production of multi‐ply plated steel coins be
accomplished within the current space and layout of the United States Mint’s
Philadelphia and Denver plants? In addition, modifying the existing facilities
to accommodate plating work stations or the handling of steel may require
capital outlays to comply with environmental and safety regulations
including permitting, waste treatment, utilities and power distribution.
3. Employees – Process changes brought on by the adoption of multi‐ply plated
steel coining technology would require a workforce re‐assessment by the
United States Mint’s facilities managers. Some workers may need to be
redeployed from their current duties, necessitating time and expense for
training. New skill competencies may be required (particularly with respect
to the new plating process), which would result in the United States Mint
incurring costs related to hiring and training new personnel. Finally, certain
positions could be eliminated, either through the obsolescence of skill sets or
reduced headcount needs, resulting in additional severance costs in the short
run, to be followed by reduced payroll costs in the long‐term.
Page 22
4. Technology License – As discussed in Section II, the RCM has issued multi‐
ply plated steel coins since 2000 using a proprietary, patented process. While
non‐infringing alternatives for manufacturing multi‐ply plated steel coins
may exist from other sources, adoption of the RCM’s technology provides an
expedient, proven solution. We are not aware of any reluctance on the part of
the RCM to license its technology to the United States Mint, although the
costs of acquiring such a license would need to be considered in any cost‐
benefit analysis under this option.
5. Production Disruptions – Potentially as important as the cost‐based issues
raised above is the timing associated with transitioning to a new coin
production process. Should the United States Mint decide to proceed with a
change to its operations, the logistics of such a transition would need to be
managed, particularly with regard to the suspension of production lines. In
order to reduce the risk of supply shortages, the United States Mint would
want to explore the feasibility of shifting production between its two facilities
(subject to capacity and conversion constraints) and/or introduce the new
alternative metal coins at appropriate intervals during the transition period.
B. Option 2 – Purchase Ready‐to‐Strike Blanks of Plated Steel Coins
As discussed in the previous section, by changing United States vended coins to
plated steel compositions the United States Mint would be faced with the challenge
of how to plate the coins prior to the striking process – as it does not currently
possess such equipment or expertise in plated coins in its facilities. The current one‐
cent coin has a copper plated zinc composition, which the United States Mint
purchases in ready‐to‐strike form from an outside supplier. Thus, the United States
Mint could contract with one or more suppliers to purchase ready‐to‐strike blanks of
plated steel coins for its vended denominations.
By choosing this option the United States Mint would be able to avoid a number of
the transition‐related issues discussed above. Machines utilized through the
plancheting stage would not need to be retooled or replaced, and its facilities would
not need to be expanded or reconfigured to accommodate plating or other new
equipment.86 The United States Mint would not have to acquire a license to utilize
the RCM’s patented technology. Finally, should the United States Mint choose to
retain its existing operations, it would be able to return to the production of alloy‐ or
clad‐based circulating coins should the need arise (due to, say, a shortage of coin‐
grade steel) or should prices of copper and nickel fall to the point where it becomes
economically viable once more.
Page 23
However, with this option there would still be important issues for the United States
Mint to address. These include the following:
1. Equipment – By purchasing ready‐to‐strike blanks, much of the equipment
currently used by the United States Mint would no longer be needed. Such
equipment could be decommissioned or placed on stand‐by status. Costs
associated with decommissioning would include removal of the equipment
from the premises, performing cleanup of hazards and contaminants, closing
utility lines, and storing or dismantling the equipment. If placed on stand‐by
status, the United States Mint would incur costs related to periodic
inspections, maintenance, and operational testing.
2. Employees – Just as equipment would be shuttered pursuant to moving to a
partial outsource option, the work force dedicated to or supporting the
operation of such equipment would no longer be needed. While this would
save payroll related costs in the future, the United States Mint would need to
assess any current period severance payments that may be incurred.
3. Supply – We are aware of three producers of multi‐ply plated steel coins: the
RCM (Canada), Jarden Zinc Products LLC (United States), and Sunshine
Minting, Inc. (United States).87 All three of these companies are suppliers to
the United States Mint. The United States Mint would have to assess the
current and planned capacity of these suppliers against the current and
projected demands of the United States Mint and of those countries that are
currently purchasing or contemplating the purchase of plated steel coins
from these suppliers.
4. Timing of Transition – While the purchasing of ready‐to‐strike coins may
seem less complex relative to developing the new process in‐house, there are
still transition issues that the United States Mint would need to address.
First, as mentioned above, when would a provider be ready to start to handle
the process for the United States Mint? How should the United States Mint
sequence the transition – all denominations at the same time or a gradual
transition over time? The answer to this last question could be influenced by
several of the aforementioned issues, such as employee transition plans and
the downsizing of the current facilities.
C. Option 3 – Outsource Plating but Keep all Other Operations In‐house
For strategic reasons, the United States Mint may place a high value on maintaining
as much of its existing machinery and work force as possible while still wishing to
transition to producing multi‐ply plated steel coins. One way to achieve that
Page 24
objective would be for the United States Mint to receive flat rolled coils of steel (as it
currently does for its alloy‐ and clad‐based production) and perform all
manufacturing steps through creation of the planchets, or rimmed blanks. The
United States Mint would then package the planchets and securely transport them to
an outside facility that would perform the plating process and subsequently return
the planchets to the United States Mint for striking.
The attractiveness of this option relative to the other two alternatives would depend
on the findings from the various issue assessments that were discussed above. For
example, should it be determined that one or both of the United States Mint’s
existing facilities cannot accommodate plating equipment without substantial new
infrastructure investments, outsourcing the plating function may prove to be
economical. Likewise, if it is determined that current suppliers do not have
sufficient capacity to manufacture plated steel planchets but they do have sufficient
capacity to plate planchets manufactured elsewhere, then the potential additional
cost of Option 3 relative to Option 2 may be justified on the basis of the United States
Mint being able to ensure an adequate supply of coins to meet expected demand
from the Federal Reserve Banks.
Of course, a mid‐stream outsourcing of the plating function would entail additional
expenses not presently incurred by the United States Mint in its full in‐house
operation. The planchets would need to be inventoried prior to being released and
re‐inventoried (including quality inspections) upon their return, with systems
designed to handle discrepancies and rejects. Transportation costs would be
dependent on the distance travelled, the volume of planchets included in each
shipment and fees for insurance. There would also be handling costs associated
with the loading and unloading of the planchets at the United States Mint and at the
plating facility.
D. Assessment of Options
Given that detailed cost data for the United States Mint’s current operations and for
the operation of a coin plating facility are not available for public inspection and
analysis, we have not evaluated the relative merits of the three options based on
expected net cost impacts. However, whichever approach the United States Mint
determines is best for the manufacture of vended coins, the decision to use multi‐ply
plated steel compositions like Canada and other countries will yield significant raw
material cost savings. Based on average historical production levels, substitution of
multi‐ply plated steel compositions for copper‐nickel alloys is likely to save the
United States Mint approximately $200 million per year in raw material costs.
Page 25
Section V – Potential Additional Revenue to the United States Mint from
Implementing an Alloy Recovery Program
As noted in Section II.B, since its issuance of circulation coins using multi‐ply plated
steel compositions, the RCM has implemented an alloy recovery program that has
generated more than $200 million in additional revenue between 2004 and 2010.
Assuming enabling legislation is enacted by Congress, the United States Mint could
execute a similar program for its current copper and nickel‐based five‐cent, dime
and quarter‐dollar coins. It is beyond the scope of our study to estimate with
precision the amount of revenue the United States Mint could expect to receive from
launching such a program. However, for the purpose of providing insight into the
potential revenue opportunity of such a program, we present a scenario based on
publicly available information and reasonable assumptions.
In Figure 11 we calculate the raw material cost associated with the five‐cent
($0.0644), dime ($0.0235) and quarter‐dollar ($0.0587) coins during fiscal year 2011.
The average annual production of each coin over the period 1982 through 2011 is
presented in Figure 19. Combining these two sets of information results in a
reasonable measure of the revenue, on a per‐coin basis, that the United States Mint
could receive from retrieving, extracting and selling the copper and nickel material
through an alloy recovery program ($0.0466). This calculation is set forth in Figure
21. The calculation assumes that the distribution of coins retrieved through an alloy
recovery program will mirror their relative unit production quantities over the past
30 years.
Figure 21: Average Per-Coin Raw Material Cost of Producing Five-Cent, Dime and
Quarter-Dollar Coins, Based on Fiscal Year 2011 Spot Prices 88
Average
Production Per Unit Total
(A) × (B)
(A) (B) (C)
Five‐Cent 1,194,895,000 0.0644$ 76,949,541$
Dime 1,962,359,000 0.0235$ 46,120,080$
Quarter‐Dollar 1,972,734,000 0.0587$ 115,894,896$
Total 5,129,988,000 238,964,517$
Average material cost per coin minted 0.0466$
Material Cost
Page 26
The number of coins reclaimed through an alloy recovery program will be
dependent on the United States Mint’s ability to access inventories of circulating
coins under the control of (a) the Federal Reserve Banks and (b) private coin
recycling companies, as well as the effectiveness of campaigns designed to
encourage the redemption of coin holdings removed from circulation. Between 1982
and 2011, 153.9 billion five‐cent, dime and quarter‐dollar coins were produced
(equal to average annual unit coin production of 5.130 billion, as shown in Figure 19,
multiplied by 30 years). If one‐third of these coins were recovered through an alloy
recovery program, the United States Mint’s additional revenue could be $2.4 billion
(equal to 51.3 billion coins multiplied by $0.0466). This calculation assumes that
current material prices do not significantly change.
We note that the United States Mint would incur costs to implement and run an
alloy recovery program, including the possible production of replacement coins out
of multi‐ply plated steel. Consistent with our assessment of the costs to change from
the current composition of vended coins to multi‐ply plated steel composition, the
United States Mint would be in the best position to determine the costs to implement
such a program. Assuming it is patterned after the RCM’s program, one would
expect that the United States Mint would also earn high margins.
Page 27
Section VI – Summary of Potential Benefits to the United States Mint from
Changing the Compositions of its Vended Coins to Multi‐ply
Plated Steel
Key findings of this study, based upon analyses conducted to date, include the
following:
• By changing the compositions of U.S. nickel, dime and quarter‐dollar coins
from copper‐nickel alloys to multi‐ply plated steel, the United States Mint
would incur significantly lower raw materials costs – approximately $200
million per year based on average historical production levels. Multi‐ply
plated steel compositions have been successfully used by the Royal Canadian
Mint to manufacture circulating coinage for Canada, as well as for more than
two dozen nations, for over a decade.
• By implementing a parallel alloy recovery program that collects and replaces
copper‐nickel alloy coins in circulation with multi‐ply plated steel coins and
salvages the copper and nickel material from the retired coins, the United
States Mint could earn over $2 billion in additional revenue based on modest
recovery levels.
Page 28
1 Coinage laws of the United States, 1792 to 1893, Third Edition – Revised and Corrected to October 17, 1893. Prepared Under the Direction of the Committee of Finance, U.S. Senate, 1893, pp. 1-6, “Act of April 2, 1792, Establishing a mint and regulating the coins of the United States.” 2 <http://www.usmint.gov/about_the_mint/historianscorner/?action=history>. “Under Rittenhouse, the Mint produced its first circulating coins -- 11,178 copper cents, which were delivered in March 1793.” 3 <http://www.treasury.gov/about/organizational-structure/bureaus>. The Mint was placed under the jurisdiction of the Treasury Department pursuant to the Coinage Act of 1873. 4 “The Constitution of the United States,” Article 1, Section 8, Clause 5. 5 Coinage laws of the United States, 1792 to 1893, pp. 1-6, “Act of April 2, 1792. Establishing a mint and regulating the coins of the United States,” Section 9. “Dollar” was defined to be “of the value of a Spanish milled dollar as the same is now current, and to contain three hundred and seventy-one grains and four sixteenth parts of a grain of pure, or four hundred and sixteen grains of standard silver.” 6 Ibid, Section 9. The specifications also provided for different weights depending on whether “pure” or “standard” (i.e., alloy) metals were used. 7 Ibid, Section 9. 8 Ibid, Section 9. 9 Ibid, Section 11. 10 Coinage laws of the United States, 1792 to 1893, pp. 15-16, “Act of June 28, 1834. Concerning gold coins of the United States, and for other purposes.” The Act directed the United States Mint to reduce the gold content in gold coins by a uniform 6%, relative to earlier compositions, while the content of silver in silver coins remained constant. This change translated to a revised legal exchange ratio of silver to gold equal to 16:1. 11 Coinage laws of the United States, 1792 to 1893, pp. 25-26, “Act of March 3, 1849. Authorizing the coinage of gold dollars and double eagles.” 12 Coinage laws of the United States, 1792 to 1893, pp. 27-28, “Act of February 21, 1853. An act amendatory of existing laws relative to the half dollar, quarter dollar, dime and half dime,” Sections 1-2. 13 Coinage laws of the United States, 1792 to 1893, pp. 34-35, “Act of May 16, 1866. An Act authorizing the coinage of five-cent pieces,” Section 1; and R.S. Yeoman, A Guide Book of United States Coins, 65th ed., Whitman, Atlanta, 2011, p. 126-131. Except for 1942-1945, the composition of the five-cent coin has not changed. 14 Coinage laws of the United States, 1792 to 1893, pp. 36-43, “Act of February 12, 1873. An act revising and amending the laws relative to the Mint, assay offices, and coinage of the United States,” Sections 15-17 and 21. Only the silver Trade Dollar (used for international commerce) is mentioned in the legislation, not the domestic silver dollar coin, suggesting the latter has been discontinued. 15 Coinage laws of the United States, 1792 to 1893, p. 59, “Act of June 22, 1874,” Section 3586. The generic term “silver coins” is used, which would include the domestic silver dollar coin. The silver dollar was reauthorized and granted full legal tender status pursuant to the Act of February 28, 1878 (p. 64) and discontinued after July 1, 1891 pursuant to the Act of July 14, 1890 (p. 71). 16 Emergency Banking Relief Act of 1933, Title I, Section 2. 17 <http://www.usmint.gov/about_the_mint/historianscorner/?action=timeline¢ury=1900>. 18 Coinage Act of 1965, Hearings Before the Committee on Banking and Currency, House of Representatives, Eighty-Ninth Congress, First Session on H. R. 8746 (Superseded by H.R. 8926), “A Bill to Provide for the Coinage of the United States,” June 4,7, and 8, 1965. 19 <http://coinhistory.info/usa/usa1965.htm>.
Page 29
20 <http://www.presidency.ucsb.edu/ws/?pid=27108>. 21 Yeoman (p. 204) states that through 1964 the half-dollar coin contained 90% silver by weight. Per the Coinage Act of 1965 (Title I, Section 101(a)), “The half dollar shall have…a core of an alloy of silver and copper such that the whole coin weighs 11.5 grams and contains 4.6 grams of silver…”; i.e., 40% silver. 22 Yeoman, p. 205. 23 Seigniorage derived from specie, or metal coins, is defined by the Mint as “the difference between the face value and cost of producing coinage.” (2010 Annual Report, p. 2). 24 “Coins and Currency: How the Costs and Earnings Associated with Producing Coins and Currency Are Budgeted and Accounted For,” United States General Accounting Office, GAO-04-283, April 2004, p. 12. 25 <http://www.imf.org/external/np/res/commod/index.aspx>. 26 Ibid. 27 United States Mint, 2006 Annual Report, p. 5. 28 United States Mint, 2011 Annual Report, p. 10. 29 Source: unit cost data reported in the United States Mint’s Annual Reports for fiscal years 2006-2011. 30 Source: seigniorage data reported in the United States Mint’s Annual Reports for fiscal years 2006-2011. 31 Source: unit cost data reported in the United States Mint’s Annual Reports for fiscal years 2006-2011. 32 <http://www.ifg.org/external/np/res/commod/index.aspx>. 33 <http://www.usmint.gov/about_the_mint/?action=coin_specifications>. 34 United States Mint, 2005 Annual Report, p. 10. See, also, Testimony of David A. Lebryk, Acting Director, United States Mint, Before the House Financial Services Subcommittee on Domestic and International Monetary Policy, Trade and Technology, General Coin Issues and H.R. 5077, “Numismatic Rarities Certainty Act of 2006”, July 19, 2006, p. 3: “The ability to keep conversion costs down is critical to our success because of the rising cost of metal and fabrication – costs we cannot control.” 35 United States Mint, 2010 Annual Report, p. 28. 36 Lebryk, p. 3. 37 110th Congress, 2nd Session, H.R. 5512, “Coin Modernization and Taxpayer Savings Act of 2008”, Section 2(2). 38 110th Congress, 1st Session, H.R. 3330, “Coinage Materials Modernization Act of 2007”, Section 2(a); and 110th Congress, 1st Session, H.R. 3956, “Coin Modernization and Taxpayer Savings Act of 2007”, Section 2(a). 39 <http://www.govtrack.us/congress/bill.xpd?bill=h110-3330> and <http://www.govtrack.us/congress /bill.xpd?bill=h110-3956>. 40 110th Congress, 2nd Session, H.R. 5512, “Coin Modernization and Taxpayer Savings Act of 2008”, Sections 3 and 4. 41 <http://www.govtrack.us/congress/bill.xpd?bill=h110-5512>. 42 <http://www.govtrack.us/congress/bill.xpd?bill=h111-6162>. 43 111th Congress, 2nd Session, H.R. 6162, “Coin Modernization, Oversight and Continuity Act of 2010”, Section 2. 44 Ibid, Section 3. 45 <http://www.govtrack.us/congress/bill.xpd?bill=h111-6162>. 46 United States Mint, 2005 Annual Report, p. 10.
Page 30
47 Ibid. 48 <http://www.mint.ca/store/mint/learn/5-cents-5300006>; <http://www.mint.ca/store/mint/learn/10-cents-5300008>; <http://www.mint.ca/store/mint /learn/25-cents-5300010>; and <http://www.usmint.gov /about_the_mint/?action=coin_specifications>. 49 “Technical Proposal on Multi-ply Technology by the Royal Canadian Mint,” Royal Canadian Mint, pp. 3, 9. 50 Ibid, pp. 4-5. 51 Ibid, pp. 4 and 7. 52 Ibid, pp. 5-6. 53 “New coins to save Canadians $10 million per year,” Canada NewsWire, October 16, 2001. The release also reported production cost savings of $42,157 per year (based on 453,300 coins) for its 50-cent coin. 54 Royal Canadian Mint, 2000 Annual Report, pp. 27, 31. The plating facility has an annual capacity of 1.2 billion pieces. 55 Royal Canadian Mint, Annual Report 2010, p. 14. 56 Ibid, pp. 39-40. 57 Royal Canadian Mint, 2004 Annual Report, p. 22. 58 Royal Canadian Mint, Annual Report: 2004 through 2010. 59 Royal Canadian Mint, 2007 Annual Report, p. 30. 60 Source: <http://www.usmint.gov/about_the_mint/?action=coin_specifications>. 61 See United States Mint, Annual Report for 2008 (p. 29), 2009 (p. 29), 2010 (p. 27) and 2011 (p. 10). 62 See, for example, <http://www.lme.com>. One thousand kilograms is equal to 2,204.62 pounds. 63 For example, see <http://www.crugroup.com>. 64 One of the Mint’s key performance measures is “cycle time”, or the time it takes material to flow through the Mint’s processes from receipt of raw material to Federal Reserve Bank order fulfillment. As discussed on page 26 of its 2006 Annual Report, the Mint seeks to “minimize the amount of time required to process raw materials into finished goods by eliminating non-value added steps from the processes and reducing the amount of raw material in inventory.” 65 Source: Figure 8 (Weight) and Figure 1 (Price per Metric Ton). 66 Source: <http://www.matweb.com> (Material Density); Figure 8 (Weight). 67 Source: <http://www.matweb.com> (Material Density); <http://www.mint.ca/store/mint/learn/5-cents-5300006> (Share of Weight); Figure 10 (Volume). 68 Source: <http://www.matweb.com> (Material Density); <http://www.mint.ca/store/mint/learn/10-cents-5300008> (Share of Weight); Figure 10 (Volume). 69 Source: <http://www.matweb.com> (Material Density); <http://www.mint.ca/store/mint/learn/25-cents-5300010> (Share of Weight); Figure 10 (Volume). 70 Source: Figure 11 (Five-Cent: Percent of Total, Total Quantity); Figure 12 (Dime: Percent of Total, Total Quantity); and Figure 13 (Quarter-Dollar: Percent of Total, Total Quantity). 71 Source: Figure 14 (Weight); Figure 1 (Price per Metric Ton – Copper and Nickel); and <http://www.crumonitor.com> (Price per Metric Ton – Steel). The prices shown reflect the average during the Mint’s 2011 fiscal year. The quoted steel price (hot-rolled coil, f.o.b. Midwest U.S. local mills) has been increased by $55 per ton to reflect the additional cost associated with the ultra-low carbon IF grade material used for minting coins.
Page 31
72 The figures reported in Figure 7 for the RCM reflect all cost impacts, both material (cost savings) and non-material (additional costs). 73 Source: Figure 9 (Current Composition Material Cost) and Figure 15 (RCM Composition Material Cost). 74 Yeoman, pp. 134-136, 157-158, 174-185; and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> 75 Yeoman, pp. 134-135, 158, 175-178. 76 Yeoman, pp. 133-136, 156-158. 77 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and Figure 18 (Per-unit Cost Savings). 78 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and Figure 18 (Per-unit Cost Savings). The prices of copper, nickel and steel were adjusted from their fiscal year 2011 averages (“No Change”) by 10% or 20%, as noted in the column and row headings, for purposes of this sensitivity analysis. 79 Per Figure 19, the mean and median values for the nickel and the dime differed by less than 2.0%. 80 Per Figure 19, median production for the quarter was 25.2% less than mean production. 81 “50 State Quarters® Program Concludes as the Most Successful Coin Initiative in U.S. History,” United States Mint, press release, dated December 8, 2008; and <http://www.usmint.gov/mint_programs/atb /?action=factSheet&pf>. 82 “50 State Quarters® Program Concludes as the Most Successful Coin Initiative in U.S. History,” United States Mint, press release, dated December 8, 2008. 83 <http://www.usmint.gov/mint_programs/atb/?action=factSheet&pf>. 84 United States Mint, 2011 Annual Report, p. 10. 85 <http://uspatterns.com>. 86 The assessment costs associated with these issues would also be eliminated. 87 “SM&RT Ideas from the Royal Canadian Mint,” Currency News, Volume 9, Number 5 (May 2011), p. 4. 88 Yeoman, pp. 134-136, 157-158, 174-185 and <http://www.usmint.gov/about_the_mint/coin_production /index.cfm?action=production_figures&allCoinsYear=2011#starthere> (Average Production); and Figure 18 (Per-unit Cost Savings).
IMPACT OF ELIMINATING THE PENNY ON
THE UNITED STATES MINT’S COSTS AND
PROFIT IN FISCAL YEAR 2011
Rodney J. Bosco
Kevin M. Davis
April 12, 2012
Page 1
Navigant Consulting, Inc. (“Navigant”) was asked to estimate the impact of eliminating
production of circulating pennies on costs incurred by the United States Mint (the
“Mint”).1 The Mint shipped 4.29 billion pennies (valued at $42.9 million) during fiscal year
2011 at a reported cost of $103.1 million (2.4 cents per coin), resulting in a net loss of $60.2
million. However, eliminating production of the penny would not eliminate this loss, and
could increase the overall loss to the Mint if production of the nickel was increased to
substitute for no production of the penny.
We analyzed publicly available information on the Mint’s past and projected operations to
identify patterns in costs related to its product offerings. We observed the following:
Cost reductions from eliminating the purchase of penny blanks will be largely offset
by the loss of revenue from shipments to the Federal Reserve Banks (FRB). In other
words, the payments received from the FRB ($42.9 million), which offset all but $4.3
million of the cost of penny blanks ($47.2 million), would not be received if the Mint
eliminated production of the penny.
The Mint’s fabrication and distribution costs include fixed components that will
continue to be incurred if the Mint eliminated the penny. Using FY 2011 balances
and prior Mint disclosures, we have estimated this fixed component to be
approximately $13 million.
The Mint’s total Selling, General & Administrative (“SG&A”) expense is not
sensitive to circulating coin demand or total sales. Thus, the $17.7 million in SG&A
assigned to the circulating penny in FY 2011would have been reallocated to other
products.
Substitution of loss‐generating nickels will offset potential cost reductions from
eliminating the penny.
Without the penny, only $4.3 million in net cost reductions would have been likely in 2011,
while an additional $25.2 million in cost reductions would have been possible, based on
2006 comments by the Mint regarding the amount of fixed production costs. However, the
substitution of nickels for pennies would have resulted in an increased net loss to the Mint
of as much as $10.9 million if penny production were not maintained. Our findings are
summarized in Figure 1.
1 This report was commissioned by Jarden Zinc Products, North America’s leading plated coin blank producer and licensee of the Royal Canadian Mint’s multi-ply plated steel technology.
Page 2
Figure 1: Impact of Eliminating the Penny on Mint Costs and Profit in FY 2011
(millions)
Yes No(Actual) (Estimate)
Value of Shipments 42.9$ ‐$
Gross Cost
Cost of Goods Sold (purchase of penny blanks) (47.2)$ ‐$
Cost of Goods Sold (fabrication and distribution) (38.2)$ (13.0)$
Sales, General and Administrative (SG&A) (17.7)$ (17.7)$
Profit (loss) before substitution effect (60.2)$ (30.7)$
Substitution of 914 million Nickels for 4.3 billion Pennies (40.4)$
Profit (loss) after substitution effect (71.1)$
Penny produced?
I. Cost Reductions from Eliminating the Purchase of Penny Blanks Will be Largely Offset by Revenue Losses from Shipments to the Federal Reserve Banks
The Mint purchases ready‐to‐strike penny blanks from an outside supplier. In fiscal year
(FY) 2011, the average price paid was 1.1 cents per blank, according to one press report.2
The Mint shipped 4.29 billion pennies to the FRB in FY 2011,3 resulting in a cost of $47.2
million. Had the penny not been produced, those costs would not have been incurred.
The value of coins shipped to the FRB is revenue to the Mint. Thus, the value of the 4.29
billion pennies shipped to the FRB in FY 2011 was $42.9 million.4 Had the penny not been
produced, those revenues would not have been received.
The net reduction in cost had the penny not been produced in FY 2011 is equal to $47.2
million in cost less $42.9 million in revenue, or $4.3 million.
II. The Mint’s Fabrication and Distribution Costs Include Fixed Components that Will Continue to be Incurred if the Mint Eliminated the Penny
Cost of Goods Sold, which comprise costs to fabricate and distribute coins, include outlays
that do not decrease with reductions in production volume. In fact, the Mint itself has
described in past Annual Reports how “fixed production costs” are spread over units
produced:
2 Chris Isidore, “Obama wants cheaper pennies and nickels,” CNNMoney.com, February 15, 2012. 3 United States Mint, 2011 Annual Report, page 11. 4 Id.
Page 3
“When production volumes decline because of lower demand, fixed production
costs are spread over fewer units. This offsets any per‐unit gains from lower base
metal costs. For example, the per‐unit metal cost of a nickel fell about $0.0154 from
$0.0815 in FY 2007 to $0.0661 in FY 2008. However, the per‐unit fixed production
costs increased $0.0082, resulting in only a small decline in the nickel overall unit
cost. Similarly, the penny unit cost fell slightly from FY 2007 because of higher per‐
unit vendor fabrication costs offset lower per‐unit metal costs. The unit costs for
dime and quarter denominations increased in FY 2008 because of higher per‐unit
fixed production costs.”5
“When production volumes decline because of lower demand, production costs are
spread over fewer units….The dime coin unit cost increased about 1.3 cents in FY
2009 largely because the 1.8 cent increase in per‐unit production cost offset the 1.0
cent reduction in per‐unit metal cost….Slight increases in per‐unit production and
SG&A costs did not offset the 3.1 cent decline in the five‐cent coin’s per‐unit metal
cost.”6
The Mint has acknowledged that a portion of penny production costs are also fixed. In
response to a question posed in a 2006 Congressional hearing, the Mint responded as
follows:
“Question: Do you have the ability to calculate how much the Mint would
lose if we were to eliminate the penny and make more nickels?
Answer: …the fixed costs associated with production of the penny would
have to be absorbed by the remaining denominations of circulating coins.
The total amount of fixed costs to be absorbed would be approximately $10.1
million over a fiscal year of production.”7
The Mint’s commentary can be seen graphically in Figure 2 (for the penny) and Figure 3
(for the nickel, dime and quarter), which compares shipments and per‐unit non‐raw
material costs from FY 2002 through FY 2011. The lines cross at FY 2007, the year before
the onset of the demand declines discussed by the Mint.8 Shipments and per‐unit costs
diverge after FY 2007,9 confirming the existence of fixed costs in the production process.
5 United States Mint, 2008 Annual Report, page 29. 6 United States Mint, 2009 Annual Report, page 30. 7 Coin and Currency Issues Before Congress: Can We Still Afford Money?, Hearing Before the Subcommittee on Domestic and International Monetary Policy, Trade and Technology of the Committee on Financial Services, U.S. House of Representatives, One Hundred Ninth Congress, Second Session, July 19, 2006. 8 Shipments in FY 2007 were lower than in FY 2006, but within the range of prior years. 9 The same pattern was observed, separately, for the nickel, the dime, and the quarter.
Page 4
Figure 2: Coins Shipped and Per-Unit Non-Raw Material Cost of Goods Sold, Fiscal Years 2002-2011 (Penny) 10
$0.000
$0.002
$0.004
$0.006
$0.008
$0.010
$0.012
$0.014
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Coin Shipments (Billions) Non‐Raw Material COGS (per coin)
Figure 3: Coins Shipped and Per-Unit Non-Raw Material Cost of Goods Sold, Fiscal Years 2002-2011 (Nickel, Dime and Quarter) 11
$0.000
$0.006
$0.012
$0.018
$0.024
$0.030
$0.036
$0.042
$0.048
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Coin Shipments (Billions) Non‐Raw Material COGS (per coin)
The Mint has not reported the fixed costs incurred in FY 2011 to produce the penny.
However, insight may be gleaned by linking Mr. Lebryk’s statement above to the Mint’s
costs at that time. In FY 2005 and FY 2006, non‐raw material costs associated with the
penny were $46.5 million and $45.2 million, respectively.12 The $10.1 million in fixed costs
cited by Mr. Lebryk represent 21.7% (FY 2005) and 22.3% (FY 2006) of the non‐raw material
10 Source: Appendix A-1. 11 Source: Appendix A-2. 12 Source: Appendix A-1. FY 2005 was the last full fiscal year prior to Mr. Lebryk’s July 2006 testimony, which occurred during FY 2006.
Page 5
costs, resulting in average fixed costs of 22% over the two years. We applied this average
to the non‐raw material costs of penny shipments incurred by the Mint in FY 2011 ($59.3
million)13 and estimated fixed costs of $13.0 million for FY 2011 in the production of the
penny. As production of the penny in FY 2011 was significantly less than in either FY 2005
or FY 2006, it is possible that fixed costs as a percent of total non‐raw material costs in FY
2011 could be higher than we have calculated.
Cost of Goods Sold for penny shipments during FY 2011 was $85.4 million. Purchases of
ready‐to‐strike blanks totaled $47.2 million (see Section I), leaving $38.2 million as the
amount attributable to fabrication and distribution operations executed by the Mint. The
fixed cost analysis performed above suggests that potential fabrication and distribution
cost reductions from the Mint eliminating the penny would have been $25.2 million ($38.2
million less $13.0 million) in FY 2011.
III. The Mint’s Total SG&A Expense Is Not Sensitive to Circulating Coin Demand or Total Sales
For FY 2011, the Mint assigned $17.7 million of SG&A expense to circulating pennies, equal
to 0.41 cents for each penny shipped.14 This was in stark contrast to prior years – a total of
$5.1 million in SG&A had been assigned to circulating penny production for the nine‐year
period FY 2002 through FY 2010.15
Since FY 2004, the Mint’s published financial statements do not report the individual
expense items and amounts included in SG&A. However, we examined historical
financial information reported by the Mint over the past decade (FY 2002 through FY 2011)
and found that total SG&A expense is not sensitive to either the amount of total sales or
the relative contributions of circulating and numismatic products.
Our findings are graphically depicted in Figures 4 and 5. In Figure 4 we compare SG&A to
total sales from all products – annual sales grew by more than 170 percent while SG&A
expense stayed relatively constant. In Figure 5 we compare SG&A to the distribution of
total sales among circulating coins (lower bars) and numismatic products (upper bars) –
circulating coins fell from 76% of total sales in 2002 to 16% in 2011 while SG&A stayed
relatively constant.
13 Source: Appendix A-1. 14 United States Mint, 2011 Annual Report, page 11. 15 United States Mint, Annual Report, 2002 through 2011. In FY 2011 the Mint changed the method it uses to allocate SG&A expense among its products from a gross margin basis to a gross cost basis. (United States Mint, 2011 Annual Report, page 10)
Page 6
Figure 4: Total SG&A Expense and Total Sales, Fiscal Years 2002‐2011 16
Figure 5: Total SG&A Expense and Composition of Sales, Fiscal Years 2002-2011 17
16 Sources: Appendix B-1 (total sales) and Appendix B-2 (total SG&A expense). 17 Sources: Appendix B-1 (shares of total sales) and Appendix B-2 (total SG&A expense).
Page 7
In Figure 6 we compare total SG&A to the number of circulating coins shipped. While
total SG&A stayed relatively constant throughout the period, there were three years in
which circulating coin shipments fell by an amount comparable to the Mint’s current (FY
2011) volume of penny shipments (4.3 billion coins):
In FY 2003, relative to FY 2002, SG&A fell 2% while circulating coin shipments fell by
3.6 billion coins or 24%
In FY 2008, relative to FY 2007, SG&A rose 10% while circulating coin shipments fell
by 4.0 billion coins or 29%
In FY 2009, relative to FY 2008, SG&A fell 7% while circulating coin shipments fell by
4.8 billion coins or 48%
Figure 6: Total SG&A Expense and Circulating Shipments, Fiscal Years 2002‐2011 18
$0
$50
$100
$150
$200
$250
0
5
10
15
20
2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
Circulating Coins ‐ Units Shipped (Billions) SG&A Expense ‐ Total (Millions)
We conclude that eliminating the penny would not generate significant reductions in the
Mint’s SG&A expenses. Instead, it would simply result in the Mint reallocating SG&A
expenses to other circulating coins and numismatic products.
IV. Substitution of Nickels for Pennies Would Offset Potential Cost Reductions
In a House Subcommittee hearing held in July 2006, acting Mint director David Lebryk
was asked about the potential substitution effects that may occur if the penny were
eliminated – specifically, what additional losses would the Mint incur if more nickels were
demanded.19 The question was likely prompted by Mr. Lebryk’s statement that current
18 Sources: Appendix B-1 (circulating coin shipments) and Appendix B-2 (total SG&A expense). 19 Coin and Currency Issues Before Congress: Can We Still Afford Money?
Page 8
production costs for the nickel exceeded the coin’s face value.20 Mr. Lebryk responded that
the Mint was unable to model the potential substitution effect but acknowledged the
potential for such substitutions by presenting a graph displaying “estimates of potential
costs based on various scenarios.”21
A scenario posed by Mr. Lebryk in his response envisioned nickel production doubling.22
In FY 2011, the Mint shipped 914 million circulating nickels at an average Cost of Goods
Sold of $0.0942,23 resulting in a loss of $0.0442 ($0.0942 less $0.05) for each nickel shipped.24
If Mr. Lebryk’s scenario were applied to FY 2011 cost and shipment data, the Mint would
have incurred a substitution‐related loss of $40.4 million (914 million × $0.0442). In
contrast, we have identified $4.3 million in net cost reductions in Section I, along with $25.2
million in non‐raw material related Cost of Goods Sold net reductions in Section II, for a
total of $29.5 million in possible net cost reductions if penny production had been
eliminated. Thus, if Mr. Lebryk’s substitution scenario were to occur, eliminating the
penny would likely have resulted in increased net costs to the Mint, relative to the current
state, of $10.9 million.
20 Testimony of David A. Lebryk, July 19, 2006. 21 Coin and Currency Issues Before Congress: Can We Still Afford Money? 22 Coin and Currency Issues Before Congress: Can We Still Afford Money? 23 United States Mint, 2011 Annual Report, page 11. 24 The Mint also assigned SG&A of $16.1 million, or $0.0176 per coin shipped, to the nickel. For the reasons set forth in Section III, we have assumed that increased demand for nickels will not result in additional SG&A expense.
Appendix A‐1
Fiscal Coins
Year Shipped Per Coin Total
(millions) (million $)
(A) × (B)
(A) (B) (C)
2002 7,520 0.0067$ 50.5$
2003 6,430 0.0075$ 48.1$
2004 7,130 0.0066$ 47.0$
2005 7,220 0.0064$ 46.5$
2006 8,500 0.0053$ 45.2$
2007 7,084 0.0074$ 52.3$
2008 5,272 0.0082$ 43.4$
2009 3,218 0.0125$ 40.2$
2010 3,487 0.0123$ 42.7$
2011 4,289 0.0138$ 59.3$
Source: Coins shipped: United States Mint, Annual Report, 2002‐2011.
Non‐Raw Material Cost (per coin): Appendix A‐3.
Non‐Raw Material Cost
Non‐Raw Material Cost of Goods Sold ‐ Penny
Fiscal
Year Nickel Dime Quarter Sum Nickel Dime Quarter Nickel Dime Quarter Sum
(dollars)
(A)+(B)+(C) (A) × (E) (B) × (F) (C) × (G) (H)+(I)+(J) (K) ÷ (D)
(A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) (L)
2002 1,302 2,633 3,616 7,551 0.0173$ 0.0145$ 0.0299$ 22.55$ 38.27$ 108.08$ 168.90$ 0.0224$
2003 744 1,884 2,418 5,046 0.0184$ 0.0149$ 0.0335$ 13.71$ 28.06$ 80.98$ 122.75$ 0.0243$
2004 1,392 2,569 2,242 6,203 0.0185$ 0.0134$ 0.0277$ 25.71$ 34.55$ 62.16$ 122.42$ 0.0197$
2005 1,418 2,669 2,656 6,743 0.0167$ 0.0123$ 0.0258$ 23.61$ 32.90$ 68.59$ 125.10$ 0.0186$
2006 1,452 3,019 3,004 7,475 0.0131$ 0.0135$ 0.0292$ 19.04$ 40.87$ 87.74$ 147.66$ 0.0198$
2007 1,289 2,247 2,711 6,247 0.0211$ 0.0141$ 0.0304$ 27.20$ 31.79$ 82.52$ 141.51$ 0.0227$
2008 647 1,070 2,510 4,227 0.0269$ 0.0167$ 0.0411$ 17.44$ 17.82$ 103.12$ 138.37$ 0.0327$
2009 207 358 965 1,530 0.0258$ 0.0346$ 0.0539$ 5.34$ 12.40$ 51.98$ 69.73$ 0.0456$
2010 359 887 252 1,498 0.0404$ 0.0274$ 0.0514$ 14.51$ 24.32$ 12.95$ 51.79$ 0.0346$
2011 914 1,403 323 2,640 0.0298$ 0.0243$ 0.0351$ 27.24$ 34.09$ 11.32$ 72.65$ 0.0275$
Non‐Raw Material Cost of Goods Sold per Coin ‐ Nickel, Dime and Quarter
Dime & Quarter)
Non‐Raw Material COGS
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ (millions) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ ($ millions) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ (dollars) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
Per CoinCoins Shipped Total Per Coin (Nickel,
Source: Coins Shipped: United States Mint, Annual Report, 2002‐2011.
Non‐Raw material COGS (per coin): Appendix A‐3.
Appendix A
‐2
Appendix A‐3
Fiscal Cost of Raw Non‐Raw Cost of Raw Non‐Raw
Year Goods Sold 1
Material Material Goods Sold 1 Material Material
(A) ‐ (B) (D) ‐ (E)
(A) (B) (C) (D) (E) (F)
2002 0.0087$ 0.0020$ 0.0067$ 0.0309$ 0.0136$ 0.0173$
2003 0.0095$ 0.0020$ 0.0075$ 0.0350$ 0.0166$ 0.0184$
2004 0.0092$ 0.0026$ 0.0066$ 0.0450$ 0.0265$ 0.0185$
2005 0.0097$ 0.0033$ 0.0064$ 0.0482$ 0.0315$ 0.0167$
2006 0.0121$ 0.0068$ 0.0053$ 0.0596$ 0.0465$ 0.0131$
2007 0.0167$ 0.0093$ 0.0074$ 0.0953$ 0.0742$ 0.0211$
2008 0.0142$ 0.0060$ 0.0082$ 0.0883$ 0.0614$ 0.0269$
2009 0.0162$ 0.0037$ 0.0125$ 0.0589$ 0.0331$ 0.0258$
2010 0.0179$ 0.0056$ 0.0123$ 0.0922$ 0.0518$ 0.0404$
2011 0.0200$ 0.0062$ 0.0138$ 0.0942$ 0.0644$ 0.0298$
Fiscal Cost of Raw Non‐Raw Cost of Raw Non‐Raw
Year Goods Sold 1 Material Material Goods Sold 1 Material Material
(G) ‐ (H) (J) ‐ (K)
(G) (H) (I) (J) (K) (L)
2002 0.0189$ 0.0044$ 0.0145$ 0.0408$ 0.0109$ 0.0299$
2003 0.0199$ 0.0050$ 0.0149$ 0.0460$ 0.0125$ 0.0335$
2004 0.0214$ 0.0080$ 0.0134$ 0.0476$ 0.0199$ 0.0277$
2005 0.0222$ 0.0099$ 0.0123$ 0.0505$ 0.0247$ 0.0258$
2006 0.0297$ 0.0162$ 0.0135$ 0.0696$ 0.0404$ 0.0292$
2007 0.0361$ 0.0220$ 0.0141$ 0.0853$ 0.0549$ 0.0304$
2008 0.0377$ 0.0210$ 0.0167$ 0.0937$ 0.0526$ 0.0411$
2009 0.0464$ 0.0118$ 0.0346$ 0.0833$ 0.0294$ 0.0539$
2010 0.0459$ 0.0185$ 0.0274$ 0.0976$ 0.0462$ 0.0514$
2011 0.0478$ 0.0235$ 0.0243$ 0.0938$ 0.0587$ 0.0351$
1 Includes Distribution to Federal Reserve Banks.
Source: Cost of Goods Sold: United States Mint, Annual Report, 2002‐2011.
Raw Material: Appendices A‐4 through A‐7.
Penny Nickel
Dime Quarter
Non‐Raw Material Cost of Goods Sold per Coin
By Denomination and Fiscal Year
Appendix A‐4
Copper Zinc Total
2011: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 9,104.04$ 2,297.80$
Material cost per coin 0.0006$ 0.0056$ 0.0062$
2010: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 7,043.74$ 2,135.13$
Material cost per coin 0.0004$ 0.0052$ 0.0056$
2009: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 4,478.95$ 1,403.71$
Material cost per coin 0.0003$ 0.0034$ 0.0037$
2008: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 7,786.78$ 2,245.49$
Material cost per coin 0.0005$ 0.0055$ 0.0060$
2007: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 7,098.21$ 3,639.43$
Material cost per coin 0.0004$ 0.0089$ 0.0093$
2006: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 6,039.99$ 2,626.48$
Material cost per coin 0.0004$ 0.0064$ 0.0068$
2005: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 3,373.84$ 1,250.22$
Material cost per coin 0.0002$ 0.0030$ 0.0033$
2004: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 2,605.25$ 1,001.52$
Material cost per coin 0.0002$ 0.0024$ 0.0026$
2003: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 1,652.64$ 788.20$
Material cost per coin 0.0001$ 0.0019$ 0.0020$
2002: Amount of material (MT) 0.0000000625 0.0000024375
Average cost per MT 1,528.99$ 777.25$
Material cost per coin 0.0001$ 0.0019$ 0.0020$
Note: Material specifications are listed in grams. A metric ton (MT) equals 1,000,000 grams.
Source: <http://www.usmint.gov/about_the_mint/?action=coin_specifications>; and
<http://www.imf.org/external/np/res/commod/index.aspx>.
Fiscal Year
Material Cost of U.S. Circulating Coins ‐ Penny
Appendix A‐5
Copper Nickel Total
2011: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 9,104.04$ 24,206.76$
Material cost per coin 0.0341$ 0.0303$ 0.0644$
2010: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 7,043.74$ 20,292.75$
Material cost per coin 0.0264$ 0.0254$ 0.0518$
2009: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 4,478.95$ 13,026.23$
Material cost per coin 0.0168$ 0.0163$ 0.0331$
2008: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 7,786.78$ 25,720.37$
Material cost per coin 0.0292$ 0.0322$ 0.0614$
2007: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 7,098.21$ 38,063.18$
Material cost per coin 0.0266$ 0.0476$ 0.0742$
2006: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 6,039.99$ 19,068.39$
Material cost per coin 0.0226$ 0.0238$ 0.0465$
2005: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 3,373.84$ 15,117.51$
Material cost per coin 0.0127$ 0.0189$ 0.0315$
2004: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 2,605.25$ 13,408.09$
Material cost per coin 0.0098$ 0.0168$ 0.0265$
2003: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 1,652.64$ 8,302.13$
Material cost per coin 0.0062$ 0.0104$ 0.0166$
2002: Amount of material (MT) 0.0000037500 0.0000012500
Average cost per MT 1,528.99$ 6,278.13$
Material cost per coin 0.0057$ 0.0078$ 0.0136$
Note: Material specifications are listed in grams. A metric ton (MT) equals 1,000,000 grams.
Source: <http://www.usmint.gov/about_the_mint/?action=coin_specifications>; and
<http://www.imf.org/external/np/res/commod/index.aspx>.
Material Cost of U.S. Circulating Coins ‐ Nickel
Fiscal Year
Appendix A‐6
Copper Nickel Total
2011: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 9,104.04$ 24,206.76$
Material cost per coin 0.0189$ 0.0046$ 0.0235$
2010: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 7,043.74$ 20,292.75$
Material cost per coin 0.0146$ 0.0038$ 0.0185$
2009: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 4,478.95$ 13,026.23$
Material cost per coin 0.0093$ 0.0025$ 0.0118$
2008: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 7,786.78$ 25,720.37$
Material cost per coin 0.0162$ 0.0049$ 0.0210$
2007: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 7,098.21$ 38,063.18$
Material cost per coin 0.0148$ 0.0072$ 0.0220$
2006: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 6,039.99$ 19,068.39$
Material cost per coin 0.0126$ 0.0036$ 0.0162$
2005: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 3,373.84$ 15,117.51$
Material cost per coin 0.0070$ 0.0029$ 0.0099$
2004: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 2,605.25$ 13,408.09$
Material cost per coin 0.0054$ 0.0025$ 0.0080$
2003: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 1,652.64$ 8,302.13$
Material cost per coin 0.0034$ 0.0016$ 0.0050$
2002: Amount of material (MT) 0.0000020790 0.0000001890
Average cost per MT 1,528.99$ 6,278.13$
Material cost per coin 0.0032$ 0.0012$ 0.0044$
Note: Material specifications are listed in grams. A metric ton (MT) equals 1,000,000 grams.
Source: <http://www.usmint.gov/about_the_mint/?action=coin_specifications>; and
<http://www.imf.org/external/np/res/commod/index.aspx>.
Material Cost of U.S. Circulating Coins ‐ Dime
Fiscal Year
Appendix A‐7
Copper Nickel Total
2011: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 9,104.04$ 24,206.76$
Material cost per coin 0.0473$ 0.0114$ 0.0587$
2010: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 7,043.74$ 20,292.75$
Material cost per coin 0.0366$ 0.0096$ 0.0462$
2009: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 4,478.95$ 13,026.23$
Material cost per coin 0.0233$ 0.0061$ 0.0294$
2008: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 7,786.78$ 25,720.37$
Material cost per coin 0.0405$ 0.0121$ 0.0526$
2007: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 7,098.21$ 38,063.18$
Material cost per coin 0.0369$ 0.0180$ 0.0549$
2006: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 6,039.99$ 19,068.39$
Material cost per coin 0.0314$ 0.0090$ 0.0404$
2005: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 3,373.84$ 15,117.51$
Material cost per coin 0.0175$ 0.0071$ 0.0247$
2004: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 2,605.25$ 13,408.09$
Material cost per coin 0.0135$ 0.0063$ 0.0199$
2003: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 1,652.64$ 8,302.13$
Material cost per coin 0.0086$ 0.0039$ 0.0125$
2002: Amount of material (MT) 0.0000051980 0.0000004720
Average cost per MT 1,528.99$ 6,278.13$
Material cost per coin 0.0079$ 0.0030$ 0.0109$
Note: Material specifications are listed in grams. A metric ton (MT) equals 1,000,000 grams.
Source: <http://www.usmint.gov/about_the_mint/?action=coin_specifications>; and
<http://www.imf.org/external/np/res/commod/index.aspx>.
Material Cost of U.S. Circulating Coins ‐ Quarter
Fiscal Year
Appendix B‐1
Circulating
Fiscal Circulating Share of
Year Bullion Other 1
Sum Coins Total Total
(A) + (B) (C) + (D) (D) ÷ (E)
(A) (B) (C) (D) (E) (F)
2002 186.7$ 253.3$ 440.0$ 1,364.2$ 1,804.2$ 76%
2003 235.4$ 234.9$ 470.3$ 916.1$ 1,386.4$ 66%
2004 315.7$ 341.2$ 656.9$ 993.5$ 1,650.4$ 60%
2005 270.7$ 355.4$ 626.1$ 1,144.8$ 1,770.9$ 65%
2006 536.6$ 514.9$ 1,051.5$ 1,271.9$ 2,323.4$ 55%
2007 356.1$ 551.5$ 907.6$ 1,727.8$ 2,635.4$ 66%
2008 948.8$ 557.2$ 1,506.0$ 1,294.5$ 2,800.5$ 46%
2009 1,694.8$ 440.0$ 2,134.8$ 777.6$ 2,912.4$ 27%
2010 2,855.4$ 413.1$ 3,268.5$ 618.2$ 3,886.7$ 16%
2011 3,471.4$ 721.7$ 4,193.1$ 776.9$ 4,970.0$ 16%
1 Includes collectible coins and national medals.
Source: United States Mint, Annual Report, 2002‐2011.
Revenue by Line of Business
(Millions of Dollars)
Numismatic Products
Appendix B‐2
Fiscal Circulating
Year Bullion Other 1
Sum Coins Total
(A) + (B) (C) + (D)
(A) (B) (C) (D) (E)
2002 1.6$ 58.1$ 59.7$ 122.4$ 182.1$
2003 1.4$ 69.6$ 71.0$ 107.9$ 178.9$
2004 0.6$ 73.1$ 73.7$ 88.9$ 162.6$
2005 0.8$ 78.8$ 79.6$ 85.9$ 165.5$
2006 1.4$ 81.5$ 82.9$ 94.6$ 177.5$
2007 1.6$ 78.9$ 80.5$ 93.5$ 174.0$
2008 8.4$ 86.7$ 95.1$ 97.0$ 192.1$
2009 12.1$ 69.2$ 81.3$ 98.1$ 179.4$
2010 21.8$ 64.7$ 86.5$ 78.2$ 164.7$
2011 26.8$ 64.7$ 91.5$ 63.4$ 154.9$
1 Includes collectible coins and national medals.
Source: United States Mint, Annual Report, 2002‐2011.
SG&A Expense by Line of Business
(Millions of Dollars)
Numismatic Products