Wood BlindsSTEP BY STEP INSTALLATION INSTRUCTIONS

Cordless Control

2800.248.8888

Table of Contents

Step 1 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Overview - Cordless Control Wood Blinds . . . . . . . . . . . . . . . . . . . . . 4

Step 2 - Mounting the Brackets . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6

Step 3 - Inserting the Headrail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 4 - Attaching the Wand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 5 - Attaching the Valance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Step 6 - Attaching optional Hold Down Clips . . . . . . . . . . . . . . . 9

Operating your Blinds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Care & Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

1 smithandnoble .com

A Smooth Set-UpWe want you to love your new blinds and that includes having

a smooth installation experience . We recommend saving

this guide. If you encounter any difficulties or questions,

please reach out to us for help . It’s why we’re here . Call us at

800 .248 .8888 for more info on installation .

We recommend you hold on to all packaging until your blinds

are fully installed . Should something go wrong (we strongly

doubt it), we want any potential returns to be a painless

as possible .

Customer Service Hours Monday — Friday: 6am — 6pm PT Saturday — Sunday: 7am — 4pm PTsmithandnoble .com

EverythingYou Need

3 4smithandnoble.com 800.248.8888

OVERVIEWSTEP 1 - PARTS & TOOLS

Cordless Control Wood BlindsFirst, make sure you have all the parts and tools required to install your shades.

ALL THE HARDWARE YOU’LL NEED: Pencil, screwdriver, ¼” nut driver, level, and a drill with a 1⁄16” drill bit.

Then find wooden studs where you’ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws.

It’s important when selecting a fastener to make sure it’s designed to support the weight of the shade . Follow the fastener manufacturer’s instruction from there on out .

Getting Started

VALANCE RETURN(OUTSIDE MOUNT

OR INSIDE MOUNT WITH CUSTOM

RETURNS ONLY)

HEADRAIL

WAND TILT(OPTIONAL)

MOUNTING BRACKETS

CENTER SUPPORTBRACKET(OPTIONAL)

Standard on 2 3⁄4" Blinds, optional on 1 3⁄8" & 2" Blinds

MOUNTING BRACKETWITH SPACER BLOCK

MOUNTING BRACKETWITH BRACKET SHIM

Used for inside mount blinds with ladder tapes only

VALANCE

Tools

Parts

POWER DRILL(NOT INCLUDED)

SCREW DRIVER (NOT INCLUDED)

PENCIL(NOT INCLUDED)

LEVEL(NOT INCLUDED)

SCREWS MOUNTING BRACKETSCENTER SUPPORT

BRACKET (OPTIONAL)

EXTENSION BRACKET(OPTIONAL)

SHIMS(OPTIONAL)

SPACER BLOCKS(OPTIONAL)

5 6smithandnoble.com 800.248.8888

CENTER SUPPORT BRACKETCENTER SUPPORT BRACKETMOUNTING BRACKET

MOUNTING BRACKET

STEP 2 - MOUNTING BRACKETSSTEP 2 - MOUNTING BRACKETS

Inside Mount

Place mounting brackets level and 1 inch from the window frame . Screw into the window frame through the holes on the inside of the bracket as shown . Always use all brackets supplied. All blinds over 54” wide require the use of center support brackets - see below on how to attach center support bracket . Always use at least two screws per bracket to ensure a strong, secure mount.

Please note: Blinds with ladder tapes require the use of the bracket shims provided to ensure proper blind operation .

Attaching Center Support BracketsFor wider blinds you will need to install center support brackets . Center support brackets should be spaced evenly along the width of the blind, aligned with tops and backs of end brackets . If needed center support brackets can be attached to an extension bracket as illustrated . Make sure the brackets are positioned so they do not interfere with the operation of blind . About 1" offset from the center ladder .

Outside or Ceiling Mount

Hold the blind in the desired position and mark the window frame or ceiling 1⁄4” past each end of the headrail with a pencil .

Remove the blind and place the mounting brackets level with the pencil marks .

Be certain that the mounting brackets are aligned with each other . Secure with the screws provided . If using extension brackets proceed to instructions below, otherwise, proceed to Step 3 .

Attaching Optional Extension Bracket for Outside Mounts:

Extension brackets are used to project the blind out from the mounting surface to clear obstructions such as window cranks and door knobs . Place extension brackets level on pencil marks . Be certain that the extension brackets are aligned with each other . Secure extension brackets to the wall with the screws supplied . Using the supplied nuts and short bolts, attach mounting bracket to extension bracket as shown .

NOTE: If mounting your brackets to a wooden window casing, pre-drill the mounting screw holes at least 1⁄4" from the edge of the wood to prevent the screws from splitting the casing .

CENTER SUPPORT BRACKET

OPTIONAL EXTENSION BRACKET BEFORE ASSEMBLY

OUTSIDE CEILING MOUNT BRACKET

1"

MOUNTING BRACKETWITH BRACKET SHIM

MOUNTING BRACKETWITH OPTIONAL

EXTENSION

7 8smithandnoble.com 800.248.8888

STEP 3 - INSERTING THE HEADRAIL

Inserting the Headrail

Check blind to ensure that all cords and ladders hang freely . Open the bracket latches by pushing up on bottom of bracket while lifting the bottom of bracket latches up . Slide the headrail into the mounting brackets . Close bracket latches into locked position . For blinds with wand control proceed to Step 4 .

HEADRAIL BRACKET LATCH

MOUNTING BRACKET

CENTER SUPPORT BRACKET

STEP 4 - ATTACHING THE WAND

Attach WandFor 1 3⁄8" & 2" slat sized blinds

Slide the plastic sleeve up to expose the hook opening . (Diagram 1)

Diagram 1

Diagram 2

Diagram 3

STEP 5 - ATTACHING THE VALANCE

Attach ValanceInsert each magnetic valance clip in the slot located at the back of the valance, spread them evenly along the valance slot .

Turn the valance clips up .

Hang the valance from the top of the headrail .

MAGNET VALANCEVALANCESLOT

PLASTIC SLEEVE

Slide the plastic sleeve down . (Diagram 3)

Note: For 2 3⁄4" slat sized blinds, the wand will come pre-attached .

Holding the plastic sleeve up, insert the wand onto the hook . (Diagram 2)

9 10smithandnoble.com 800.248.8888

OPERATING THE BLINDSSTEP 6 - ATTACHING OPTIONAL HOLD DOWN CLIPS

Hold-down clips are used to secure the bottom rail of the blind in situations where excessive movement may be a problem. To install, place the hold-down pins in the bottom rail end holes . Lower bottom rail and close slats . Position the hold down clips so that they will align with the pins to secure the bottom rail . Secure hold-down clips with screws .

To unhook your hold-down clips once mounted, move the bottom rail in the appropriate direction to disengage the pins from the clip .

INSIDE MOUNT

OUTSIDE MOUNT

PIN

PIN

OPTIONAL HOLD DOWN CLIP

OPTIONAL HOLD DOWN CLIP

Alignment

After installing the blinds, tilt the slats to the open position . Then raise and lower the blind several times . This motion will allow the cords and slats to properly align themselves .

Blind Removal

Remove the valance, then raise the slats to the headrail and lock them into place . Open both side mounting bracket door latches and pull forward to remove the blind .

To raise or lower the blind, gently hold the center of the bottom bar of the blind and either push up to lift or pull down to lower .

11 12smithandnoble.com 800.248.8888

TROUBLESHOOTING CARE & CLEANING

PROBLEM SOLUTION

My blind doesn’t lift.Check to make sure cord is not caught in headrail. If hold down clips were used, make sure they have been released.

My blind will raise and lower but will not tilt.

Your brackets may be mounted too close to the top of the window casement, causing the tilt mechanism to bind. If your blind has decorative cloth tapes, use the shims provided to move the blind away from the casement. Or Check inside the headrail for obstructions. Make sure all of the slats are laying properly on the ladders.

My inside mounted blind slides back and forth between the brackets when operated.

Using a screwdriver, bend out the adjustable end tabs on the sides of the headrail.

One side of the blind does not raise.

Make sure the lift cords are still fastened to the bottom rail. If they are not please call customer service for assistance.

OrLook inside the headrail to make sure that cords are not caught on or under something.

Care & Cleaning

Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your blinds looking fresh and neat. For maximum results, lower blinds to full length, then tilt slats until almost fully closed to dust. Repeat for reverse side of slats .

13 14smithandnoble.com 800.248.8888

Child Safety

SAFETY NOTES

Safety First . Style Second To None™ .

Great style should never come at the cost of safety . Every Smith & Noble window treatment conforms strictly to today’s safety standards, including permanent tie-down devices and built-in cord stops . Mount the cord cleat at a safe height, taking into account furniture or other objects upon which a child may climb. Then, after each use of the shade, simply wrap the excess cord around the cleat. It's fast, easy and safe. To obtain a free cord cleat call us at 800 .248 .8888 or visit smithandnoble .com/childsafety . To protect young children and pets, there’s no better way to eliminate risk than to use one of our cordless products .

© 2019 Smith & Noble Home, Inc. All Rights Reserved SN122019

Warranty Service

The enjoyment of your window covering should be everlasting, which is why our products come with a limited lifetime warranty . The warranty applies to the original owner, requires a proof of purchase (hang on to your receipt!) and covers defects in material or craftsmanship . Hardware must have been properly installed . We reserve the right to determine if your hardware warrants a repair or a replacement . Visit smithandnoble.com/guarantee to see full details . In need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair or replacement ASAP .