Date post: | 07-Apr-2018 |
Category: |
Documents |
Upload: | shahzad-anwar |
View: | 246 times |
Download: | 1 times |
of 17
8/3/2019 STRONG Laser Engraver Operation Manual
1/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
ContentsOperation Manual -------------------------------------------------------------2
1. Preface -------------------------------------------------------------------------------------------2
2. Attention ----------------------------------------------------------------------------------------33. Operation of Hypogyny Machine -------------------------------------------------- 3
3.1 Function and operation of key-press ---------------------------------------------------- 3
4. Process Operation ------------------------------------------------------------------- 54.1 Boot-strap show ---------------------------------------------------------------------------- 5
4.2 Manual Operation -------------------------------------------------------------------------- 5
4.3 Automation --------------------------------------------------------------------------------- 5
5. Processing Setup --------------------------------------------------------------------- 75.1 Go back to zero (Go zero operation) ---------------------------------------------------- 7
5.2 Operation for go zero ---------------------------------------------------------------------- 8
5.3 Manual processing speed switch and adjustment -------------------------------------- 8
5.4 Pause processing and location adjustment ---------------------------------------------- 8
5.5 Processing exit, stop point saving and processing ------------------------------------10
5.6 Advanced processing ---------------------------------------------------------------------- 11
6. Menu Setup --------------------------------------------------------------------11
6.1 Machine parameter setup ---------------------------------------------------------------- 11
6.2 Processing parameter setup -------------------------------------------------------------- 12
6.3 System parameter setup ------------------------------------------------------------------ 12
6.4 Laser parameter setup -------------------------------------------------------------------- 126.5 Advanced processing setup -------------------------------------------------------------- 13
7. Laser Host Program --------------------------------------------------------------------------15
7.1 Host program introduction ----------------------------------------------------------------- 15
7.2 Setup ------------------------------------------------------------------------------------------ 15
7.3 Software process ---------------------------------------------------------------------------- 17
7.4 Laser process parameter------------------------------------------------------------------- 18
7.5 CorelDraw menu commands -------------------------------------------------------------- 19
1. PREFACE
Thank you for choosing STRONG Laser Engraver, please operate and use the
8/3/2019 STRONG Laser Engraver Operation Manual
2/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
machine according to this manual. If there is any question, please contact our company as
soon as possible.
Inlay DSP, the core of this system, has high integration grade, whose super functionis listed below:
1.1 Absolute offline operation and work steadily;
1.2 Read the file in U-disk directly;
1.3 Process any size code (disposed by epigyny software of RZ laser) file which is made
by coredraw12 or 13, PLT file and G cord file which is made by Artcut Laser;
1.4 Check-up process file in advance, avoid code writing error, prevent the place of
material exceeding process range;1.5 Diagnose in-out, parameter, and emanatory impulse and back zero signals, improve the
ability of long-distance maintenance;
1.6 Automatism and dynamic upgrade;
1.7 The system supports Chinese and English simultaneously;
1.8 Take battery by itself, cutting electricity protect and resume are more reliable;
1.9 Processing is steady, uniformity and leading to a diminution of machine shake
effectively;
1.10 Support high subsection, insure high precision and speed processing;
1.11 Support beeline, circular arc and curve interpolation directly;
1.12 Pitch on all processing loca then output and born one processing file.
Users satisfaction is the goal of our service.
If you have any question or advice, please visit our website: www.signstech.com to
inquire and leave words.
Thanks for your support and cooperation.
http://www.signstech.com/http://www.signstech.com/8/3/2019 STRONG Laser Engraver Operation Manual
3/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
2. ATTENTION
2.1 Dont use this machine in strong disturb and magnetic filed condition.2.2 Dont insert and pull out U-disk when control card is running.2.3 Waterproof, dustproof, fireproofing
2.4 Avoid metal and other lead electricity matter enter into shell.2.5 Dont take down and no parts can be repaired inside by user.2.6 Energize need moderation when insert and pull out U-disk and other link line2.7 Please break off the electricity and keep proper if not use for a long time2.8 Dont take easy lead electricity thing (snail, metal chipping etc.), tinder (oil, dust etc.)
into control card by accident to prevent inducing fire.2.9 Please cut off power supply before connection to prevent get an electric shock or injured
by electricity2.10 Please screw terminal snail in term of normal moment value, for fear void connect to
induce fire.
3. Operation of Hypogyny Machine
3.1 Function and operation of key-press
3.1.1 Key-press of panel arrays as follows (Chart 3-1)
3-1
Chart 3-1
3.1.2 Function of key-press on panel as follows
Key
NameFunction
3
8/3/2019 STRONG Laser Engraver Operation Manual
4/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
Positive move of X axis, input fig.1, choose up move of menu
Positive move of Y axis, input fig.2, choose differ option attribute in menu
Input fig. 3
Input fig. 4, set up work zero of X axis and Y axis
Negative move of X axis, input fig. 5, choose down move of menu
Negative move of Y axis, input fig. 6, choose differ option attribute in menu
Input fig. 7
Set up work zero of z axis, input fig.8
Input fig.9, all axis go back zero in hand move state
Input fig.0choose high/low speed in hand move state
Input radix point, open or close light of dot moving laser in hand move state
Enter into menu setting, minus inputting, choosing pagination of processing
file, select epigyny machine controlling and transfer quadratic programmer
Confirm the zero position of all axis and diversified choice, input and
operation
Choose sequence, stepper, distance three modes in hand move state
Delete the input figure, run processing file or pause processing
Adjust the high or low speed data in hand move state, stop processing and
cancel diversified choice, input and operation when work
4. PROCESS OPERATION
4.1. Boot-strap show:
4
8/3/2019 STRONG Laser Engraver Operation Manual
5/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
Go to home?
Press key to enter to the manual operation state; press key, machine go to zero andenter to the manual operation state.
4.2. Manual Operation
Manual OperationAfter go to zero, system enter to the manual operation state as follow:
1X 60.000 Manual1Y 80.000 Laser off
1Z 0.000 High spdcontinue
Chart 4-1In Manual operation state, press key to change high speed and low speed to process. If
the current state is High speed, press key change to Low speed. If the current state is
Low speed, press key change to High speed.
4.3. Automation
Operation steps
4.3.1 Confirm work origin: In Manual operation state, move X and Y axis to process point
press key to clear, confirm X, Y axis work origin.
4.3.2 Choose document: After confirm work origin press keyappears the screen as
below:
Choose Document:U Disk listInternal List
5
8/3/2019 STRONG Laser Engraver Operation Manual
6/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
Chart 4-2
Press and key to choose the document, press key to enter document list, press and
key to move cursor, press and key to skip two rows to move the cursor, press key to
cancel.
4.3.3 Processing parameter setup:
Find the target document then press key, user should input the processing parameter,
including process speed, blank line speed, cutting power, turning power, scan power and jog
time.
Process spd 8000.00Blank li ne speed 6000.00Cutting Power 50.00Turning Power 47.00Scan spd 30000.00
Scan power 35.00Jog time 1
pulse /mmX axis 400.00
Y axis 400.00Z axis 400.0 0
Chart 4-3
Press and key to choose different setup items, press key to enter data adjustment, after
input the data, press to confirm, and then press and to choose next item. After
changing, press to confirm, system start to check the code, then start to process.
5. Processing Setup
5.1. Go back to zero (Go zero operation)
The origin is the mechanical zero of the machine, so go back to zero is also called gozero operation. The functions of control system rely on the operation of go back to zero,such as break-point processing function, cutting electricity renew function, etc. If there
6
8/3/2019 STRONG Laser Engraver Operation Manual
7/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
is no go back to zero operation, the above functions will not carry on. Generally, doingonce go zero operation before the processing can delete the accumulation error.
Go zero setup:
Press keythe cursor will be in Machine parameter setup item press key to
enter, press key to move cursor at Go Zero setup, then press key to enter, the cursor
will be in Go zero speed press key to enter speed setup as follows:
Go zero spd mm/minX axis : 7000.00Y axis : 7000.00Z axis : 1000.00
Chart 5-1
Input the data at the cursor. If input wrong, press key to delete last character; if
finished, press key to confirm new datacursor will come to Y axis setup automatically; if
do not want change it press key, the cursor will come to next item. After setup, system
will back to the last menu.
Press key to move cursor at Go zero direction item press key to set up as
below
Go zero directionX axis : positiveY axis : negativeZ axis : negative
Chart 5-2
The cursor is in the X axis setup automatically, press and key to change data, press
key to move cursor to next item, and press key to confirm and back to last menupress
key to cancel change and back to last menu.Generally, X is positive, Y is negative
5.2. Operation for go zero
Open the power, screen show: go to home? press keyXY axis will go zero,
7
8/3/2019 STRONG Laser Engraver Operation Manual
8/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
press key, the two axis do not go zero and enter to the manual operation state. In manual
operation state press keyXY axis come to working origin.
5.3. Manual processing speed switch and adjustment
In manual operation state press key to enter current speed mode setup, if the current
manual processing speed is low speed, the screen shows:
Low spd: mm/min
Y axis : 1200.00Z axis : 600.00
X axis : 1200.00
Chart 5-3
The cursor points at X axis low speed setup, press and to choose the item. If you
want changing, then press to enter data setup, input data, press to confirm, or press
to cancel; if input the wrong data, press to delete the last data.
5.4. Pause processing and location adjustment
Press to pause processing file the run in the screen change to pause the
machine stops working, at this time you can adjust the location for X, Y axis, the systems
default movement mode is stepper, the move speed is low speed, user can adjust the distance
between two axis slightly. That is to say, it can move the distance of a low speed gridding
when press one time; if need quick and large adjust, you can press key, the mode change
stepper to high speed, the movement will move continuously. After adjustment, press
screen show
Original location
Chart 5-4
The operator needs to confirm whether to reserve the adjustment of the position between two
axis. Press key, system back to the location before changing and to start processingpress
key, system will start at new location to process.
8
8/3/2019 STRONG Laser Engraver Operation Manual
9/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
5.5. Processing exit, stop point saving and processing
If use wants to stop the processing, press , the screen shows:
1X 80.000 Run1Y
1Z 0.000 Low spd
Save stop point?
690.000 Laser off
Chart 5-5The system will clue to: whether save the stop point if you want save current
processing point, press it means that current processing point is saved at No.1 stop-
pointThe system could save No.123456 point.after input 1LCD show
1X 80.000 Run1Y 690.000 Laser off1Z 0.000 Low spdSave stop point? 1
Chart 5-6
After Input Stop point 1 and press to confirmthe screen show whether go back tozero? in the left as follow:
1X 80.000 Run
1Y1Z 0.000 Low spd
Go to origin?
690.000 Laser off
Chart 5-7
If want to continue processing from stop point press combination key + you
should first press and dont loosen then press at the same timeand thenunloosen
togetherthe machine continue to process materials at stop point 1 that you saved. Also, if
you want to processing in stop point 2, press combination key + .
(Note: before to process, the machine should go back to zero.)
5.6. Advanced processing
Array repeated processing
It should setup the array processing parameter in the menu see also the array processing
9
8/3/2019 STRONG Laser Engraver Operation Manual
10/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
setup , and transfer this function from the senior processing. The operation setup is as
follow:
1. Press and to choose array repeated processing press to enterthen press
and to move cursor choosing different documents
2. Press to enter document menuthen press and moving cursor to choose target
document
3. Setup the processing parameter the after operation is same as general processing
operation.
4.Repeated processing
Press and at same time to run the document that used in last time.
6. Menu Setup
Enter into Menu
When the machine goes back to zero point, then, the system is in the manual state as follows.
1X 60.000 Manual1Y 80.000 Laser off1Z 0.000 High spdcontinue
Chart 6-1
Press to enter into the menu, it has five parameters as follows:
Machine SetupAuto Pro Setup
System SetupLaser Para Setup
Adv. Pro Se tupVersion View
Chart 6-2
6.1. Machine parameter setup
10
8/3/2019 STRONG Laser Engraver Operation Manual
11/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
6.1.1 pulse setupdefaultdo not amendavoid processing error
6.1.2 Table size setup
when enter into the item of machine size setupcursor is in numerical value of X axis
automatic, if need to changeinput the data directly press to confirm then cursor
will move down one row till back to last menuIf do not change press back to last
menu.generally, it is smaller than the size of processing table-board
If the processing size exceeds the machine table size, the system will clew automatic that
the processing over the areafor example: over positive limit of X axis. If move the
two axis in manual state, manual and stop in top right corner will counterchange
quickly when reach limit position and it will be clewed that exceed the limit in the screen.
6.1.3 motor direction setupdefault
6.1.4 Go Zero setupdefault6.1.5 Voltage Setupdefaultdo not amend
6.1.6 Output Pulse definitiondefaultdo not amend
6.1.7 Speed Limitdefaultdo not amend
6.2. Processing parameter setup
6.2.1 Linear accelerationdefaultcurrently 600-1000
6.2.2 Curve accelerationdefaultcurrently 800-2000
6.2.3 Start skip speeddefaultcurrently 300
6.2.4 Scan accelerationdefaultcurrently 13200-13500
6.3. System parameter setup
6.3.1. Languages
Original system is Chinese, if need change to English, press and move cursor to
English and press key, the content of all label files and menu files change to English.
6.3.2 Function Configuredefault
6.3.3 Inner of Formatting
It needs this operation when the internal document has disorderly code. Please move cursor to
this item, press to entry, screen shows as follows.
Percent change quickly, clew that format is finished when percent is 100%, press to
confirm and back to last menu.
11
8/3/2019 STRONG Laser Engraver Operation Manual
12/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
6.3.4 key data of formatdefault
6.3.5 check itself inputdefaultdo not enter
6.3.6 check itself ouputdefaultdo not enter
6.3.7 buttons checkdefault
6.3.8 system updatedefault
6.4. Laser parameter setup:
6.4.1 Scan speed
It is the laser head moving speed when the laser scanning. Generally, it is good between 0
30000mm/min according for the processing and tool requirements. The machine does not
wobble during processing is the measure.
6.4.2 Configure laser power
It is the laser tube power for engraving. The data is between 0100%user should choose
appropriate data base on the materials and engraving speed.
6.4.3 Configure scan power
It is the laser tube power for scanning. The data is between 0100%user should choose
appropriate data base on the materials and scan speed.
6.4.4 Configure Turning Power
The laser power of Scan processing for the corners. The data is between 0100%user
should choose appropriate data base on the materials and scan speed. Its data is smaller
than the scan power.
6.4.5 Laser Scan Interval
Setup in the software.
6.4.6 Jog time
If set up for 5, so the laser open time is 5ms for point movement.
6.4.7 Laser Max Frequencydefault
6.4.8 Laser Minimal Frequencydefault6.4.9 Laser Working Frequencydefault
6.4.10 Minimal Travel Speeddefault
6.4.11 Jog Power Setupdefault
6.4.12 Max Duty Rationdefault
12
8/3/2019 STRONG Laser Engraver Operation Manual
13/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
6.4.13 Laser Advancedefault
6.5. Advanced processing setup
6.5.1 Array movement setup
If the user need to processing one file to several files, there is two ways: 1. in each sculpt
software, copy this file and born to a code file and output, the control card treats this code file
as one file, and then transfer to operate. 2. the collocation of array movement of inside control
card, copy the uncopied single file and download to control card, then set the need processing
row and number of columns, and the distance between the row and column, herein, the copy
function of sculpt software is finished.
The operation steps
When the cursor in this itempress the screen as follows:
Row ColumnRow Space ColumnAl ternation Time
Chart 6-3
Press to setupthe cursor will be in the array linage dataif need changeinput the
data directly press to confirmthe cursor will come to array number of columns data
automatically. If do not change press back to last menu.
Press to move cursor to row space between and space between columns, the
cursor will be in the row spacing data automatically if need to change input the data
directly press to confirm the cursor will come to space between columns data
automatically. If do not change press back to last menu.(The space between is the centredistance for two work-piece)
Press to move cursor to array alternation time press to setup. Array alternation time
is the system pause time after finished one processing file. Input the data at cursor place, press
to confirm and back to last menu. If do not change, press back to last menu. If change the
time to negativethe system will stop processing when one work-piece finished, and press
13
8/3/2019 STRONG Laser Engraver Operation Manual
14/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
any key to continue.
6.5.2 Document maintenance
Look over document(default)
Copy documentCopy the target file to inside file, it could copy the document to handle
from U disk, but can not copy inside files to U disk. Press and key to move the cursor.
When it finished the system back to the last menu automatically. document could be
copied from computer to handle
Delete document: (default)
6.5.3 Machine Edition Displaydefault
7. Laser Host Program
7.1 Host program introduction:
This software is for laser process.It combines with the software CorleDraw and makeseasy and to design the target graphic. And this host program works with our laser controlsystem to control laser cutting, laser sweeping, laser engraving motions.This host programsupports Coreldraw12, Coreldraw13 versions.
7.2 Setup
7.2.1Setup CorelDraw to C:\Program Files\Corel7.2.2Open the host program CD and click on SETUP.EXE file, click Next Step for
following windows and set the host program to C:\Program Files\Corel7.2.3Copy ZHB.GMS file in setupand paste it to Corel\Corel Graphics 12\Draw\GMS;7.2.4Open CorelDraw, select Tools menu and click Select, and then select
Coustom(Figue2); then select Macro command and select the 3rd macro commandGlobaMacros.Module1.zhbin the help window add laser Process(as figure1), itwill create a new button, and copy GlobaMacros.Module1.zhb to the left side of the
Tools in CorelDraw (Figure2)Then you set a laser process icon in CorelDraw.
7.2.5After setting the laser process icon, click in in CorelDraw and willappears.
14
8/3/2019 STRONG Laser Engraver Operation Manual
15/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
Figure1 Figure2
7.3 Software ProcessIn CorelDraw, the sweeping method of vendor graph or character sweeping are basic
divided into edge sweeping and area sweeping. In this software, we identify the edgesweeping as cutting, while area sweeping as sweeping(Scanning); Processed BMP imagebelongs to sweeping.
7.3.1Image Sweeping
1SweepingSelect the target graph or characters, click right button of the mouse, select the Property
Processor, click to choose sweeping color; then click and set width as 0 in Edgeitwill just sweep the inner part of the graph or the words.
2CuttingSelect the target graph or characters, click right button of the mouse, select the Property
Processor, click and select (no sweeping)Click and set width as filament inEdge, it will just to sweep the graph and words outside edge.
3Male SweepingSelect the drawn graph and its outside square, unit them as one graph by choosing
Combination in Arrange, click right button of the mouse, in Property Processorwindow;
click and select color, click and set set width as 0 in Edge.
15
8/3/2019 STRONG Laser Engraver Operation Manual
16/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
4Line SweepingBecause the line is not closed, our suggestion is you can choose rectangle with
small width to replace.
Figure3
5Image SweepingFor gray image file processed by CorelDraw orPhotoShopit can be imported byCorelDraw and use this host program to output and sweep. You just need to click
button to set its process parameter.When you process the image file inCorelDraw orPhotoShop , you need to adjust the graphs brightness and contrast, then changeit into a gray graph, then change it into a bitmap file, finally change this bitmap file into graygraph, it is the file which can be processed.
7.3.2 Trace output Setup
After having processed graph files in CorelDraw , click and
button showsclick this button and enter Process Property figure 3select yourprocess mode, then click left button of the mouse to set process parameter, click Trace and
enter the file download window, click to save the trace as a file, click to send the trace tothe controller. The unselected trace will not be outputted, and it is also possible to outputmulti traces to one file.
7.4 Laser Process Parameter:
7.4.1Laser Sweeping ParameterLaser Power: the percent is to adjust the laser output power, users need to adjust
it for different working materials and speed.Speed: machine sweeping speed, unit mm/minInterspace: Sweeping interspaces between two column, unit: mmModethere are several sweeping modes: single sweeping and bilateral sweeping.
Single sweeping can not be affected by offset, while bilateral sweeping, you must to set the
16
8/3/2019 STRONG Laser Engraver Operation Manual
17/17
STRONG SIGNS DIGITECH Co,.Ltd WWW. SIGNSTECH.COM
right offset value to get a good process effect.
Acceleration: unit mm/s2 the default value is13500 mm/s2the max value is 30000mm/s2.
Acceleration space: machine motion increase and decrease distance, unit mm, defaultvalue is 15mm
Offsetin order to get a good process effect for counteracting error which causedmachine moving, it needs to set the offset sometimes, especially for bilateral sweeping. Lasercutting or single sweeping get nothing to do with this value, unit: mm
7.4.2Laser cutting parameterLaser power: laser generator output power when it cuts.Speed: laser machine motion speed, unit: mm/min.Linear Acceleration: speed increase and decrease ability of signal motor, unit: mm/s2Curve Acceleration: speed increase and decrease ability of multi motors motion,unit:mm/s2
NoteIf sweeping speed is V(unit: mm/s), its acceleration is a, its space is S, thenV = 2 * a
* S.
7.5 CorelDraw Menu commands
Commands Menu Shortcut button
Property Processor Right button of mouseto select target graph
ALT + ENTER
Combination ArrangeCombination CTRL + L
Location ArrangeChangeLocation
ALT + F7
Size ArrangeChangeSize ALT + F10
17