Struct RefData Overview SM3D

Structural Reference Data Marine Mode Guide

Version 2014 R1 (10.1)

June 2014

2 Structural Reference Data Marine Mode Guide

Copyright

Copyright 2007-2014 Intergraph Corporation. All Rights Reserved. Intergraph is part of Hexagon.

Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains

confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.

Portions of this software are owned by Spatial Corp. 1986-2014. All Rights Reserved.

Portions of the user interface copyright 2012-2014 Telerik AD.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with

subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the

United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS 252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.

Unpublished - rights reserved under the copyright laws of the United States.

Intergraph Corporation 300 Intergraph Way

Huntsville, AL 35813

Documentation

Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides, Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a

particular software product.

Other Documentation

Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support, SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph

as guidance for using a software product.

Terms of Use a. Use of a software product and Documentation is subject to the End User License Agreement ("EULA") delivered with the

software product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the Licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take

precedence and govern the use of this software product and Documentation. Subject to the terms contained within the

applicable license agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the Documentation as defined in the applicable license agreement and delivered with the software product for Licensee's internal,

non-commercial use. The Documentation may not be printed for resale or redistribution.

b. For use of Documentation or Other Documentation where end user does not receive a EULA or does not have a valid license agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other

Documentation for Licensees internal non-commercial use. Intergraph Corporation gives Licensee permission to print a reasonable number of copies of Other Documentation for Licensees internal, non-commercial. The Other Documentation may not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and for any reason by Intergraph Corporation by giving written notice to Licensee.

Disclaimer of Warranties

Except for any express warranties as may be stated in the EULA or separate license or separate terms and conditions, Intergraph Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability

and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its

publication date.

The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL

EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

Structural Reference Data Marine Mode Guide 3

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.

Limitation of Damages

IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL,

SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATIONS LIABILITY EXCEED THE AMOUNT THAT INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN

CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2) YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.

IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.

Export Controls

Intergraph Corporations software products and any third-party Software Products obtained from Intergraph Corporation, its subsidiaries, or distributors (including any Documentation, Other Documentation or technical data related to these products) are subject to the export control laws and regulations of the United States. Diversion contrary to U.S. law is prohibited. These Software

Products, and the direct product thereof, must not be exported or re-exported, directly or indirectly (including via remote access) under the following circumstances:

a. To Cuba, Iran, North Korea, Sudan, or Syria, or any national of these countries.

b. To any person or entity listed on any U.S. government denial list, including but not limited to, the U.S. Department of Commerce

Denied Persons, Entities, and Unverified Lists, http://www.bis.doc.gov/complianceandenforcement/liststocheck.htm, the U.S. Department of Treasury Specially Designated Nationals List, http://www.treas.gov/offices/enforcement/ofac/, and the U.S.

Department of State Debarred List, http://www.pmddtc.state.gov/compliance/debar.html.

c. To any entity when Licensee knows, or has reason to know, the end use of the Software Product is related to the design, development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or sensitive

nuclear uses.

d. To any entity when Licensee knows, or has reason to know, that an illegal reshipment will take place.

Any questions regarding export or re-export of these Software Products should be addressed to Intergraph Corporations Export Compliance Department, Huntsville, Alabama 35894, USA.

Trademarks

Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Sketch, SmartMarine, IntelliShip, ISOGEN, SmartSketch, SPOOLGEN, SupportManager, SupportModeler, Sapphire, and Intergraph Smart are trademarks or registered trademarks of

Intergraph Corporation or its subsidiaries in the United States and other countries. Hexagon and the Hexagon logo are registered trademarks of Hexagon AB or its subsidiaries. Microsoft and Windows are registered trademarks of Microsoft Corporation. ACIS is a

registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics, Presentation Layer Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are

trademarks of Infragistics, Inc. Incorporates portions of 2D DCM, 3D DCM, and HLM by Siemens Product Lifecycle Management Software III (GB) Ltd. All rights reserved. Gigasoft is a registered trademark, and ProEssentials a trademark of Gigasoft, Inc.

VideoSoft and VXFlexGrid are either registered trademarks or trademarks of ComponentOne LLC 1991-2013, All rights reserved. Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Tribon is a

trademark of AVEVA Group plc. Alma and act/cut are trademarks of the Alma company. Other brands and product names are

trademarks of their respective owners.


Contents Preface ................................................................................................................................................... 9

Documentation Set ............................................................................................................................ 9 Documentation Comments............................................................................................................... 12 Smart 3D and Oracle ....................................................................................................................... 12 What's New in the Structural Reference Data Overview ................................................................... 12

Profile Cross Sections ......................................................................................................................... 15

Cross Section Symbol B .................................................................................................................. 15 Cross Section Symbol BUL2 ............................................................................................................ 16 Cross Section Symbol BUL3 ............................................................................................................ 18 Cross Section Symbol BUT .............................................................................................................. 19 Cross Section Symbol C_SS............................................................................................................ 20 Cross Section Symbol C_SType ...................................................................................................... 21 Cross Section Symbol EA ................................................................................................................ 23 Cross Section Symbol FB ................................................................................................................ 24 Cross Section Symbol HalfR ............................................................................................................ 25 Cross Section Symbol I.................................................................................................................... 27 Cross Section Symbol I_SType ........................................................................................................ 28 Cross Section Symbol P .................................................................................................................. 30 Cross Section Symbol R .................................................................................................................. 31 Cross Section Symbol SB ................................................................................................................ 32 Cross Section Symbol SqTu ............................................................................................................ 33 Cross Section Symbol T .................................................................................................................. 34 Cross Section Symbol T_SType ...................................................................................................... 34 Cross Section Symbol UA ................................................................................................................ 35

Member Cross Sections ...................................................................................................................... 37

Cross Section Symbol 2L ................................................................................................................. 38 Cross Section Symbol BUBoxFM ..................................................................................................... 40 Cross Section Symbol BUC ............................................................................................................. 42 Cross Section Symbol BUCan ......................................................................................................... 44 Cross Section Symbol BUCone ....................................................................................................... 46 Cross Section Symbol BUEndCan ................................................................................................... 47 Cross Section Symbol BUFlat .......................................................................................................... 49 Cross Section Symbol BUI ............................................................................................................... 50 Cross Section Symbol BUIHaunch ................................................................................................... 52 Cross Section Symbol BUITaperWeb............................................................................................... 54 Cross Section Symbol BUIUE .......................................................................................................... 56 Cross Section Symbol BUL .............................................................................................................. 58 Cross Section Symbol BUT .............................................................................................................. 60 Cross Section Symbol BUTube ........................................................................................................ 61 Cross Section Symbol C (MC) ......................................................................................................... 63 Cross Section Symbol CS ................................................................................................................ 65 Cross Section Symbol HSSC (Pipe) ................................................................................................. 66 Cross Section Symbol HSSR ........................................................................................................... 67 Cross Section Symbol HW ............................................................................................................... 68

Contents


Cross Section Symbol HWWF ......................................................................................................... 69 Cross Section Symbol L ................................................................................................................... 71 Cross Section Symbol Rect ............................................................................................................. 73 Cross Section Symbol RectC ........................................................................................................... 74 Cross Section Symbol RectCWF...................................................................................................... 75 Cross Section Symbol RectWF ........................................................................................................ 77 Cross Section Symbol RS ................................................................................................................ 78 Cross Section Symbol S .................................................................................................................. 79 Cross Section Symbol ST ................................................................................................................ 81 Cross Section Symbol T (MT) .......................................................................................................... 82 Cross Section Symbol W (M) ........................................................................................................... 84 Cross Section Symbol Wedge.......................................................................................................... 86 Cross Section Symbol WedgeWF .................................................................................................... 87

Assembly Connections for Members .................................................................................................. 89

GenAssyConnSel ............................................................................................................................ 89 MbrAxisByOnMember ...................................................................................................................... 91 MbrAxisByEdge ............................................................................................................................... 92 MbrAxisByFCAndOS1Edge ............................................................................................................. 94 MbrAxisByFCAndOSNoEdge ........................................................................................................... 95 MbrAxisByEdgeAndOS2Edge .......................................................................................................... 97 MbrAxisByEdgeAndOS1Edge .......................................................................................................... 98 MbrAxisByOSAndOS2Edge ........................................................................................................... 100 MbrAxisByOSAndOS1Edge ........................................................................................................... 101 MbrAxisByOSAndOSNoEdge ........................................................................................................ 103 Codelists ....................................................................................................................................... 105

End Cut Shape ........................................................................................................................ 106 Shape Outside ........................................................................................................................ 106 Extend or Offset ...................................................................................................................... 108 Shape at Edge ........................................................................................................................ 110 Shape at Edge Overlap ........................................................................................................... 113 Shape at Edge Outside............................................................................................................ 115 BraceTpeCol ........................................................................................................................... 117 BraceConnTpeCol ................................................................................................................... 118

Chamfers ............................................................................................................................................ 121

Single Sided Chamfers .................................................................................................................. 121 Double Sided Chamfer................................................................................................................... 122

Brackets ............................................................................................................................................. 123

Slots and Collars................................................................................................................................ 127

Slot A ............................................................................................................................................ 128 Slot C ............................................................................................................................................ 130 Slot C2 .......................................................................................................................................... 140 Slot I .............................................................................................................................................. 141 Non-Tight Clips .............................................................................................................................. 148 Tight Collars .................................................................................................................................. 152

Contents


Corner Features for Plates and Profiles ........................................................................................... 161

Corner Features for Members ........................................................................................................... 167

Edge Features .................................................................................................................................... 177

Sketched Features ............................................................................................................................. 183

End Cuts for Profiles ......................................................................................................................... 185

Welded Web Cuts .......................................................................................................................... 186 Clip Web Cuts................................................................................................................................ 195 Cutback Web Cuts ......................................................................................................................... 195 Snip Web Cuts............................................................................................................................... 196 Edge Reinforcement Web Cuts ...................................................................................................... 199 Flange Cuts ................................................................................................................................... 199

End Cuts for Members ....................................................................................................................... 205

Along-Axis Web Cuts for Members ................................................................................................ 208 Web-penetrated Center Cuts ................................................................................................... 208 Web-penetrated Top Cuts ....................................................................................................... 213 Web-penetrated Bottom Cuts .................................................................................................. 221 Web Non-penetrated Cuts ....................................................................................................... 229

Along-Axis Flange Cuts for Members ............................................................................................. 231 Flange-penetrated Center Cuts................................................................................................ 231 Flange-penetrated Top Cuts .................................................................................................... 235 Flange-penetrated Bottom Cuts ............................................................................................... 247 Flange Non-penetrated Cuts .................................................................................................... 254

Web Cuts for Split Members .......................................................................................................... 258 Flange Cuts for Split Members ....................................................................................................... 263 Mitered Web Cuts for Members ..................................................................................................... 264 Mitred Flange Cuts for Members .................................................................................................... 265 Free-end Web Cuts for Members ................................................................................................... 266 Free-end Flange Cuts for Members ............................................................................................... 268

Advanced Plate Systems ................................................................................................................... 271

Side Plates .................................................................................................................................... 272 Ring Plates .................................................................................................................................... 273 Continuity Plates ............................................................................................................................ 273 Transition Plates ............................................................................................................................ 274 Buckling Plates .............................................................................................................................. 275 Brackets ........................................................................................................................................ 276 Insert Plates .................................................................................................................................. 277

Physical Connections ........................................................................................................................ 279

Butt Welds ..................................................................................................................................... 279 Tee Welds ..................................................................................................................................... 284

Molded Conventions .......................................................................................................................... 289

Deck Molded Conventions ............................................................................................................. 289 Transverse Bulkhead Molded Conventions .................................................................................... 290

Contents


Longitudinal Bulkhead Molded Conventions ................................................................................... 291 Hull Molded Conventions ............................................................................................................... 292

Index ................................................................................................................................................... 293


This document is an overview of the Intergraph SmartTM 3D structural reference data library. The marine library is used by tasks such as Molded Forms, Structural Detailing, Planning, and Structural Manufacturing as a base set of reference data and a starting point for customization. You can use this document to determine the available reference data and compare it with the standards of your company.

This overview is not intended to be a substitute for reference data training, so it does not describe how to customize, install, or maintain the data.

Documentation Set Intergraph SmartTM 3D Documentation is available as Adobe PDF files. The content is the same as the online Help. To access these PDF documents, click Help > Printable Guides in the software.

The documentation set is divided into four categories:

Administrative guides contain information about installing, configuring, customizing, and troubleshooting.

User's guides provide command reference and how-to information for working in each task.

Reference data guides define the reference data workbooks. Not all tasks have reference data.

ISOGEN guides.

Administrative Guides

Intergraph SmartTM 3D Installation Guide - Provides instructions on installing and configuring the software.

Project Management User's Guide - Provides instructions for setting up the databases, creating permission groups, backing up and restoring project data, assigning access permissions to the model, defining and managing locations for Global Workshare, and version upgrade.

Global Workshare Guide - Provides instructions for setting up the software and the databases to work in a workshare environment.

Interference Checking Guide - Provides information on installing, configuring, and using the interference detection service.

Integration Reference Guide - Provides information about installing, configuring, and using Smart 3D in an integrated environment.

Interpreting Human Piping Specifications - Provides information about how to interpret human piping specifications so that you can create the corresponding piping specification in the software.

Design and Data Exchange with PDMS - Provides information about how to export model data from Smart 3D to PDMS and from PDMS to Smart 3D. Specific guidelines relating to best practices and known limitations of the export functionality are also included.

Preface

Preface


Export to Plant Design System (PDS) User's Guide - Provides information about how to export model data from Smart 3D to PDS. Specific guidelines relating to best practices and known limitations of the export functionality are also included.

Point Cloud Reference - Provides information for referencing point cloud files provided by point cloud vendors in Smart 3D.

Troubleshooting Reference Guide - Provides information on how to resolve errors that you might encounter in the software by documenting troubleshooting tips, error messages, and To Do List messages.

Plant Design System (PDS) Guide - Provides all information needed to use PDS with Smart 3D. Topics include referencing active PDS projects in Smart 3D, exporting PDS data and importing that data into Smart 3D, and converting PDS reference data to Smart 3D reference data.

Intergraph SmartTM 3D Programmer's Guide - Provides information about custom commands, naming rules, and symbol programming. If you install the Programming Resources, this document is delivered to the [Product Folder]\Programming\Help folder.

User's Guides

Catalog User's Guide - Provides information about viewing, editing, and creating reference data and select lists (codelists).

Civil User's Guide - Provides information about routing trench runs in the model.

Common User's Guide - Provides information about defining workspaces, manipulating views, and running reports.

Compartmentation User's Guide - Provides instruction for placing volume objects such as compartments and zones in the model.

Electrical User's Guide - Provides information about routing electrical cable, cableway, cable tray, and conduit.

Equipment and Furnishings User's Guide - Provides information about placing equipment.

Geometry Analysis and Repair User's Guide - Provides instructions for importing and exporting model data, checking the data against a defined set of requirements, and repairing the data.

Grids User's Guide - Provides instructions for creating coordinate systems, elevation grid planes, vertical grid planes, radial cylinders, radial planes, grid arcs, and grid lines.

Hangers and Supports User's Guide - Provides instructions on placing piping, duct, and cableway supports in the model.

Hole Management User's Guide - Provides instructions for placing, reviewing, and approving holes in a structure.

HVAC User's Guide - Provides instructions for routing HVAC duct.

Molded Forms User's Guide - Provides instructions for placing hull, bulkheads, major openings, stiffeners, and other major structural components in the model.

Orthographic Drawings User's Guide - Provides information about creating and managing orthographic drawings.

Piping Isometric Drawings User's Guide - Provides information about creating and managing piping isometric drawings.

Piping User's Guide - Provides instructions for routing pipe and placing valves, taps, and pipe joints.

Preface


Planning User's Guide - Provides instructions about defining the assembly hierarchy (production bill of material) by creating blocks and assemblies and by specifying the assembly sequence.

Reports User's Guide - Provides information about creating and managing spreadsheet reports.

Space Management User's Guide - Provides instructions for placing space objects such as areas, zones, interference volumes, and drawing volumes in the model.

Structural Analysis User's Guide - Provides instructions for defining loads, load cases, load combinations, and the importing and exporting of analytical data.

Structural Detailing User's Guide - Provides instructions for creating, detailing, and maintaining the structural members of a model.

Structural Manufacturing User's Guide - Provides instructions for creating and maintaining manufacturing objects such as templates, jigs, and margins.

Structure User's Guide - Provides instructions for placing structural members, such as beams, columns, slabs, openings, stairs, ladders, equipment foundations, and handrails.

Systems and Specifications User's Guide - Provides instructions for creating systems and selecting the available specifications for each system type.

Reference Data Guides

2D Symbols User's Guide - Provides command reference information and procedural instructions for creating 2D symbols used to represent collars, clips, profiles, brackets, and other items.

2D Symbols Reference Data Guide - Provides information about the two-dimensional symbols used in all tasks.

Civil Reference Data Guide - Provides information about trench straight features, turn features, reference data.

Compartmentation Reference Data Guide - Provides information about compartmentation reference data.

Drawings and Reports Reference Data Guide - Provides information about reports reference data.

Electrical Reference Data Guide - Provides information about electrical cable, cableway, cable tray, and conduit reference data.

Electrical 3D Symbols Reference - Provides information about the cable tray and conduit 3D symbols that are available.

Equipment and Furnishings Reference Data Guide - Provides information about equipment reference data.

Equipment 3D Symbols Reference - Provides information about the equipment, equipment component, design shapes, and design aides 3D symbols that are available.

Hangers and Supports Reference Data Guide - Provides information about hangers and supports reference data.

Hangers and Supports 3D Symbols Reference - Provides information about the hanger and support 3D symbols that are available.

Hangers and Supports SmartPart Symbols Reference - Provides information about the hanger and support SmartPart symbols that are available.

Preface


Hole Management Reference Data Guide - Provides information about hole reference data.

HVAC Reference Data Guide - Provides information about HVAC reference data.

HVAC 3D Symbols Reference - Provides information about the HVAC 3D symbols that are available.

Reference Data Guide - Provides instructions about the Bulkload utility, codelists, and the reference data common to several disciplines.

Piping Reference Data Guide - Provides information about piping reference data including piping specifications, piping specification rules, piping parts, and piping symbols.

Piping 3D Symbols Reference - Provides information about the piping 3D symbols that are available.

Space Management Reference Data Guide - Provides information about space management reference data.

Structure Reference Data Guide - Provides information about structural reference data.

Structure 3D Symbols Reference - Provides information about the stair, ladder, footings, and equipment foundation 3D symbols that are available.

Structural Reference Data Overview - Provides an overview of the marine mode structural reference data library.

ISOGEN Guides

Symbol Keys Reference Guide - Provides information about the symbol keys for isometric drawings. This guide is from Alias, the makers of ISOGEN.

Documentation Comments We welcome comments or suggestions about this documentation. You can send us an email at: [email protected].

Documentation updates for supported software versions are available from https://smartsupport.intergraph.com (https://smartsupport.intergraph.com).

Smart 3D and Oracle Throughout the software and documentation, there are references and options pertaining to Oracle databases. Intergraph SmartTM 3D plant mode supports Oracle, but marine mode and material handling mode do not. Please remember that when using marine mode or material handling mode, always select the SQL option when given a choice between Oracle and SQL.

What's New in the Structural Reference Data Overview

The following changes have been made to the Structural Reference Data Overview.

Version 2014 R1 (10.1)

Replaced out-of-date bracket symbols with general bracket descriptions and symbol locations. For more information, see Brackets (on page 123). (P2 CP:232313)

Preface


Version 2014 (10.0)

Added Generic_2B_01 to the General Assembly Connection Selection table. For more information, see GenAssyConnSel (on page 89) (P2 CP:216531).

Added insert plate to the list of advance plate systems. For more information, see Insert Plates (on page 277).

Preface



S E C T I O N 1

Profile cross sections are used in the Molded Forms task. The symbols are delivered to [Reference Data Folder]\SharedContent\Profile Xsections

In This Section Cross Section Symbol B ............................................................. 15 Cross Section Symbol BUL2 ....................................................... 16 Cross Section Symbol BUL3 ....................................................... 18 Cross Section Symbol BUT ......................................................... 19 Cross Section Symbol C_SS ....................................................... 20 Cross Section Symbol C_SType ................................................. 21 Cross Section Symbol EA ........................................................... 23 Cross Section Symbol FB ........................................................... 24 Cross Section Symbol HalfR ....................................................... 25 Cross Section Symbol I ............................................................... 27 Cross Section Symbol I_SType ................................................... 28 Cross Section Symbol P ............................................................. 30 Cross Section Symbol R ............................................................. 31 Cross Section Symbol SB ........................................................... 32 Cross Section Symbol SqTu ....................................................... 33 Cross Section Symbol T.............................................................. 34 Cross Section Symbol T_SType.................................................. 34 Cross Section Symbol UA ........................................................... 35

Cross Section Symbol B

Profile Cross Sections



The B bulb angle profile cross-section symbol (B.sym) uses the following symbol parameters. Each symbol parameter is defined and given a default value in the symbol file. Each occurrence of a symbol bulkloaded into the catalog can be assigned different parameter values.

1 TCR - Top corner radius

2 FL - Flange length

3 Slope - Slope of the bottom of the bulb flange.

4 WL - Web length

5 CR - Corner radius

6 FR - Fillet radius of the bulb flange

7 WT - Web thickness

Cross Section Symbol BUL2

The BUL2 profile cross-section symbol uses the following properties.

Section Name - Type the section name. This name appears when you label members. The section name must be unique across the catalog.

Short Name - Type the short name for the section.

Alternate EDI Name - Type the Electronic Data Interchange name for the section. This name is used when translating sections through CIMsteel. This property is currently not used.



Description - Type a short description if needed.

Area - Type the cross-section area for the section. The area is defined in square inches or square millimeters.

Depth - Type the depth for the section (Web Length). The depth is defined in inches or millimeters.

Width - Type the breadth for the section. The breadth is defined in inches or millimeters.

Perimeter - The outside perimeter distance for the section.

CentroidX - Type the location of the centroid along the local x-axis. The location is defined in inches or millimeters.

CentroidY - Type the location of the centroid along the local y-axis. The location is defined in inches or millimeters.

Moment of Inertia about X (Ixx) - Type the moment of inertia for the section's local x-axis.

Moment of Inertia about Y (Iyy) - Type the moment of inertia for the section's local y-axis.

Warping Statical Moment (Sw) - Type the warping statical moment for the section.

Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x- axis.

Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y- axis.

Torsional Moment of Inertia (J) - Type the torsional moment of inertia for the section.

Warping Constant (Cw) - Type the warping constant for the section.

Flexural Constant (H) - Type the flexural constant for the section.

Polar Radius of Gyration about Shear Center (ro) - Type the polar radius of gyration about the shear center.

Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x- axis.

Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y- axis.

Radius of Gyration about Principle XY (Rxy) - Type the radius of gyration about the local z- axis. The radius is defined in inches or millimeters.

Plastic Section Modulus about X (Zxx) - Type the plastic section modulus for the section's local x-axis.

Plastic Section Modulus about Y (Zyy) - Type the plastic section modulus for the section's local y-axis.



Cross Section Symbol BUL3

The BUL3 profile cross-section symbol uses the following properties.



























Cross Section Symbol BUT



Cross Section Symbol C_SS

The C_SS profile cross-section symbol uses the following properties.














Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.

Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.







Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.

Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.




Cross Section Symbol C_SType

The C_SType profile cross-section symbol uses the following properties.








Cross Section Symbol EA The EA profile cross-section symbol uses the following properties.



























Cross Section Symbol FB

The FB profile cross-section symbol uses the following properties.



























Cross Section Symbol HalfR

The HalfR profile cross-section symbol uses the following properties.





Cross Section Symbol I

The I profile cross-section symbol uses the following properties.



























Cross Section Symbol I_SType The I_SType profile cross-section symbol uses the following properties.





Cross Section Symbol P

The P profile cross-section symbol uses the following properties.



























Cross Section Symbol R

The R profile cross-section symbol uses the following properties.



























Cross Section Symbol SB

The SB profile cross-section symbol uses the following properties.

Name - Type the section name. This name appears when you label members. The section name must be unique across the catalog.


























Cross Section Symbol SqTu



Cross Section Symbol T

Cross Section Symbol T_SType The T_SType profile cross-section symbol uses the following properties.
















Elastic Section Modulus about X (Sxx) - Type the section modulus for the section's local x-axis.

Elastic Section Modulus about Y (Syy) - Type the section modulus for the section's local y-axis.





Radius of Gyration about X axis (Rxx) - Type the radius of gyration for the section's local x-axis.

Radius of Gyration about Y axis (Ryy) - Type the radius of gyration for the section's local y-axis.




Cross Section Symbol UA



The UA profile cross-section symbol uses the following properties.


























S E C T I O N 2

Member cross-section symbols are used in the Structure task.

All section tables delivered with the software use a specific set of cross-section symbols. Some section tables use all the cross-section symbols in the set; some tables only use a subset of the cross-section symbols. Each cross-section symbol has its own set of properties. When looking at a section table workbook, you can determine the cross-section symbol that is being referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the sheet.

The cross-section symbols are delivered with the reference data software in the [Reference Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-section symbols, sometimes referred to as arbitrary sections, using the 2D Symbols utility that is delivered with the software.

The software uses the simple physical representation of the cross-section symbol to display the member geometry in the model. You can change the display representation using the Selected Aspects option of Format > View.

The delivered symbols contain a detailed physical representation. This representation is available only for marine models, and is not used for plant and materials handling models.

The delivered symbols also contain a production physical representation. This representation is available only for marine models in the Structural Manufacturing task, and is not used for plant and materials handling models.

For more information, see Cross-Section Symbol Representations in the 2D Symbols User's Guide.

Member Cross Sections



In This Section Cross Section Symbol 2L ............................................................ 38 Cross Section Symbol BUBoxFM ................................................ 40 Cross Section Symbol BUC ........................................................ 42 Cross Section Symbol BUCan..................................................... 44 Cross Section Symbol BUCone................................................... 46 Cross Section Symbol BUEndCan .............................................. 47 Cross Section Symbol BUFlat ..................................................... 49 Cross Section Symbol BUI .......................................................... 50 Cross Section Symbol BUIHaunch .............................................. 52 Cross Section Symbol BUITaperWeb .......................................... 54 Cross Section Symbol BUIUE ..................................................... 56 Cross Section Symbol BUL ......................................................... 58 Cross Section Symbol BUT ......................................................... 60 Cross Section Symbol BUTube ................................................... 61 Cross Section Symbol C (MC)..................................................... 63 Cross Section Symbol CS ........................................................... 65 Cross Section Symbol HSSC (Pipe) ............................................ 66 Cross Section Symbol HSSR ...................................................... 67 Cross Section Symbol HW .......................................................... 68 Cross Section Symbol HWWF..................................................... 69 Cross Section Symbol L .............................................................. 71 Cross Section Symbol Rect......................................................... 73 Cross Section Symbol RectC ...................................................... 74 Cross Section Symbol RectCWF ................................................. 75 Cross Section Symbol RectWF ................................................... 77 Cross Section Symbol RS ........................................................... 78 Cross Section Symbol S ............................................................. 79 Cross Section Symbol ST ........................................................... 81 Cross Section Symbol T (MT) ..................................................... 82 Cross Section Symbol W (M) ...................................................... 84 Cross Section Symbol Wedge ..................................................... 86 Cross Section Symbol WedgeWF ............................................... 87

Cross Section Symbol 2L The 2L cross section symbol defines double-angle sections and uses the following properties.

Section Name - Type the section name. This name appears when you label members. The section name must be unique within the section standard.


EDI Name - Type the Electronic Data Interchange name for the section. This name is used when translating sections through CIMsteel. This property is currently not used.



Group Id - Type the material group identification for the section.

Unit Weight - Type the weight of the section. The unit weight is defined in mass per length, pound per foot (lb/ft).

Area - Type the cross-sectional area for the section. The area is defined in square inches or square millimeters.

Depth - Type the depth for the section (longer legs). The depth is defined in inches or millimeters.

d - Type the other depth for the section (shorter legs). The depth is defined in inches or millimeters.

bf - Type the width of a single angle. The width is defined in inches or millimeters.

Width - Type the width of the entire section. The width is defined in inches or millimeters.

Perimeter - Type the outside perimeter of the section.

tf - Type the flange thickness for the section. The thickness is defined in inches or millimeters.

tw - Type the web thickness for the section. The thickness is defined in inches or millimeters.

kdesign - Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on the welded section.

kdetail - Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on welded section.

bb - Enter the back-to-back spacing on the section.

CentroidY - Type the centroid location along the y-axis. The location is defined in inches or millimeters.

Ixx - Type the moment of inertia for the section's local x-axis.

Zxx - Type the plastic section modulus for the section's local x-axis.

Sxx - Type the section modulus for the section's local x-axis.

Rxx - Type the radius of gyration for the section's local x-axis.

Ryy - Type the radius of gyration for the section's local y-axis.

ro - Type the polar radius of gyration about the shear center.

H - Type the flexural constant.

bb Configuration - Specifies which legs of the angles are placed back-to-back. Type 0 for equal leg angle. Type 1 to place the long legs back-to-back. Type 2 to place the short legs back-to-back.



lsg - Specify the bolt gage for the long side when there is one bolt row. For more information, see Member Cross Sections.

lsg1 - Specify the gage distance to the first bolt row on the long side when there are two bolt rows.

lsg2 - Specify the gage distance between the first and second bolt rows on the long side when there are two bolt rows.

ssg - Specify the bolt gage for the short side when there is one bolt row.

ssg1 - Specify the gage distance to the first bolt row on the short side when there are two bolt rows.

ssg2 - Specify the gage distance from the first bolt row to the second bolt row on the short side when

Date post:	17-Sep-2015
Category:	Documents
Upload:	rmnrajan
View:	20 times
Download:	5 times

Struct RefData Overview SM3D

Documents