Established by Henning Schmidt in 2002, FSI Power-tech ApS develops and manufactures stump cutters. This has been the company’s key competency since its foundation, and it has built up extensive know-how and expertise in the mechanical challenges involved in cutting tree stumps.
From its factory in Ølholm near Tørring in central Jutland, the company services all of its customers and dealers in Denmark, and importers from a large number of countries in Europe. The company also exports to other countries around the world, including America, Australia and New Zealand.
FSI stump cutters are aimed at professional users, who are pri-marily landscape gardeners, tree felling companies, developers, hire companies, municipalities, housing associations and similar companies with activities in the green sector.
FSI ensures the high quality of all of its products by carrying out quality assurance and testing on all of its stump cutters before they are shipped.
We want every customer who uses an FSI stump cutter to be fully satisfied with its performance
FSI power-tech ApS
The FSI range of stump cutters consists of three groups of machines, defined by their power source.
TRIPLEX Teeth SystemEvery FSI stump cutter is equipped with TRIPLEX cutting teeth. The teeth are round and during operation the wearing surface covers about 120 degrees, so the teeth can be rotated three times before they have to be replaced. The teeth are fitted using a single nut.
The teeth are fitted in holders made from durable cast steel. The holders are fixed on the cutter wheel so that adjustments are not necessary when replacing teeth or holders. For increased capacity, the holders are fitted in a staggered system on the disc, so that each tooth cuts its own track.
Power clutchPower clutch, the clutch between the engine and the cutter wheel is a strong and unique hydraulic clutch with integrated brake. The clutch engages smoothly and efficiently, with 4 x cylinders and when the clutch is disengaged, the brake activates automatically.
Tree stump cutting timesIn collaboration with some of our customers, we have devised an overview of the time taken to cut up three different diameters of tree stumps. The figures are based on the cutting of a tree stump that is 15 cm high and which extends for 15 cm below the ground. The times stated in the table can vary depending on the tree species, the age of the stump, the machine operator and the power of the actual tool carrier.
Explanation of product namesB = Petrol H = Hydraulic T = Tractor D = Diesel S = Swing
EngineThe machine is powered by
its own engine
HydraulicThe unit is powered by hydraulics
from e.g. a mini loader, excavator or similar tool carrier
TractorThe cutter wheel is powered by the
PTO shaft and up/down and sideways movement is hydraulically controlled
FSI Stump Cutters
Engine Hydraulic PTO
FSI B20 FSI H20/H20S FSI T25
FSI B22 FSI H40/H40S FSI T27
FSI B28 FSI H52 FSI T65
FSI D30 FSI H65
FSI D74
Stump diameter Ø40 cm Ø65 cm Ø105 cm
B20
En
gin
e
12 minutes 25 minutes 90 minutes
B22 10 minutes 20 minutes 70 minutes
B28 7 minutes 15 minutes 40 minutes
D30 6 minutes 12 minutes 35 minutes
D74 3 minutes 6 minutes 15 minutes
H20/H20S
Hyd
rau
lic
25 minutes 30 minutes 100 minutes
H40/H40S 12 minutes 25 minutes 75 minutes
H52 7 minutes 18 minutes 45 minutes
H65 3 minutes 6 minutes 15 minutes
T25
Trac
tor
8 minutes 15 minutes 45 minutes
T27 6 minutes 12 minutes 35 minutes
T65 3 minutes 6 minutes 15 minutes
For more information, visit our website www.fsi.dk
B20Engine
Product dataEngine . . . . . . . . . . . . . . . . . . . . . 8.2 kW/11 HP Honda - PetrolTank capacity . . . . . . . . . . . . . . . . . . . . . 6.1 l - approx. 3 hoursWheel drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ManualBrakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . One for each wheel
Cutter disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . Ø370 mmTeeth/qty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ø20.5/8Dimensions L x W x H . . . . . . . . . . . . 1800 x 680 x 1100 mmWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 kg
• Height-adjustable handlebar
• Handlebar vibration reduction
• Safety bar
• Separate brakes
• Centred pivot point
• Compact W = 68 cm
• Large stump range
Towable stump cutter with petrol engineB20 is a compact and balanced stump cutter that can be used to cut up all types of tree stumps.
The pivot joint between the stump cutter and the chassis ensures easy and smooth cutting, even under difficult conditions.
The brakes can be applied individually to each wheel, so the machine can easily access the stump even if there are shavings in the way. The individual brakes can also be used to negotiate steps with ease.
Extra equipmentDrawbar for ball and socket coupling, for transport up to 10 km/h. Not permitted on public roads.
Hour counter with alarm for every 25 hours for lubrication and for every 100 hours for oil change. Can be retrofitted.
Special colour instead of the original FSI red. Extra delivery time shall be expected.
Swing
800 mm
Height/Depth
300 mm
200 mm
Machine width
680 mm
Chip depth
Max.: 23.5 mm
For more information, visit our website www.fsi.dk
B22Engine
Stump cutter with 2WD and petrol engineFSI B22 is a new stump cutter that combines the many areas of application of the B20 but which is also self-propelled, so that moving over uneven terrain is much easier, and especially when loading or unloading from a trailer. Hydraulic wheel drive, speed and forward/reverse are controlled from the handlebar. A free-running feature ensures that the machine can be moved without having to start the engine.
A swivel joint between the stump cutter and the chassis ensures an easy and smooth swing movement for the stump cutter, without
the wheels having to be moved. This ensures fast and efficient stump cutting, even on inclined or uneven surfaces.
Extra equipmentHour counter with alarm for every 25 hours for lubrication, and for every 100 hours for oil change. Can be retrofitted.
Special colour instead of the original FSI red. Extra delivery time shall be expected.
Product dataEngine . . . . . . . . . . . . . . . . . . . . 10.5 kW/14 HP Kohler - PetrolTank capacity . . . . . . . . . . . . . . . . . . . . . 6.1 l - approx. 3 hoursWheel drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2WD HydraulicBrakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . One for each wheel
Cutter disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . Ø370 mmTeeth/qty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ø20.5/8Dimensions L x W x H . . . . . . . . . . . . 1740 x 680 x 1250 mmWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 kg
• Handlebar vibration reduction
• Safety bar
• Separate brakes
• Centred pivot point
• Compact W = 68 cm
• 2-wheel drive
• Large stump range
Swing
900 mm
Height/Depth
300 mm
250 mm
Chip depth
Max.: 23.5 mm
Machine width
680 mm
For more information, visit our website www.fsi.dk
B28Engine
Product dataEngine . . . . . . . . . . . . . . . . . . . 19.8 kW/26.5 HP Kohler - PetrolTank capacity . . . . . . . . . . . . . . . . . . . . . 35 l - approx. 7 hoursWheel drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2WD HydraulicBrakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic
Cutter disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . Ø470 mmTeeth/qty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø20.5/16Dimensions L x W x H . . . . . . . . . . . . 2700 x 800 x 1160 mmWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 kg
Stump cutter with 2WD and petrol engineFSI B28 is for the serious professional user who carries out stump cutting jobs.
All operations, including moving and stump cutting, are controlled via the integrated control panel. The control panel can be used to engage/disengage the differential lock as well as to adjust the speed of the swing movement.
Very safe; the safety bar on the control panel must be enabled to start the cutter head.
Control panel (B28 and D30)
Extra equipmentTwin wheel set with centre bolt and standard tyres 18 x 7-9. Width + 550 mm
Twin wheel set with centre bolt and tractor profile tyres 18 x 9.50-8. Width +580 mm
LED work light. On/Off via control panel.
Special colour instead of the original FSI red. Extra delivery time shall be expected.
Twin wheels with tractor profile
• Swivelling control panel
• Safety bar
• 2-wheel drive
• Hydraulic control
• Compact W = 80 cm
• Large stump range
Swing
1350 mm
Height/Depth
800 mm
380 mm
Machine width
800 mm
Chip depth
Max.: 48 mm
For more information, visit our website www.fsi.dk
Product dataEngine . . . . . . . . . . . . . . . . . . . . . 22 kW/30 HP Kubota - DieselTank capacity . . . . . . . . . . . . . . . . . . . . 35 l - approx. 10 hoursWheel drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2WD HydraulicBrakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic
Cutter disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . Ø470 mmTeeth/qty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø24.5/16Dimensions L x W x H . . . . . . . . . . . . 2700 x 1350 x 1220 mmWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725 kg
D30Engine
D30: Stump cutter with 2WD and diesel engineFSI D30 is for serious users who use a stump cutter regularly in their work. The diesel engine provides high performance capacity and excellent operating efficiency.
All operations, including movement and actual stump cutting, are controlled via the integrated control panel. The control panel can be used to engage/disengage the differential lock as well as to adjust the speed of the swing movement.
Very safe; the safety bar on the control panel must be enabled to start the cutter head.
Extra equipmentTwin wheel set with centre bolt and tractor profile tyres 18 x 9.50-8. Width 1380 mm.
Special colour instead of the original FSI red. Extra delivery time shall be expected.
D30 TRACK: Stump cutters on tracks with diesel motorFSI D30 TRACK is the well-known D30 stump cutter which is equipped with tracks instead of wheels. It is aimed at serious users who often work in very inaccessible terrain. The diesel engine pro-vides high performance capacity and excellent operating efficiency.
All machine operation is executed via the rotatable control panel, so the operator can stand behind the machine during operation and move towards the work site, and the control panel can be turned during stump cutting, providing a good overview of the stump during the stump cutting process. The speed of swing movement can also be controlled from the control panel.
Very safe; the safety bar on the control panel must be enabled to start the cutter head.
D30 TRACK REMOTEThe same as the D30 TRACK but equipped with complete radio remote control of all of the functions.
Extra equipment
D30• Swivelling control panel
• Safety bar
• 2-wheel drive
• Twin wheel set
• Hydraulic control
• Compact W = 80 cm
• LED work light
• Large stump range
D30 TRACK• - same as D30 PLUS
• Off-road vehicle
• Vari-track
• Compact W = 77.5 cm
• LED work light
• Rear-fitted dozer
blade option
• Weight 970 kg
Swing
1350 mm
Height/Depth
800 mm
380 mm
Machine width
D30 800/1350 mm D30 TRACK 800/1050 mm
Chip
Max.: 52 mm
For more information, visit our website www.fsi.dk
Product data Cutting disc
Model Oil flow Max. pressure Motor requirement Diameter Teeth/qty. Weight
H20 30–50 l/minute 250 bar 12–22 kW/15–30 HP Ø370 mm Ø20.5/12 70 kg
H40 50–75 l/minute 250 bar 18–31 kW/25–42 HP Ø470 mm Ø24.5/16 150 kg
H52 80–110 l/minute 300 bar 29–48 kW/40–65 HP Ø570 mm Ø24.5/20 240 kg
H65 100-130 100–130 l/minute 350 bar Max. 76 kW/100 HP Ø720 mm Ø28/28 500 kg
H65 135-160 135–160 l/minute 350 bar Max. 85 kW/115 HP Ø720 mm Ø28/28 500 kg
H65 165-200 165–200 l/minute 350 bar Max. 117 kW/160 HP Ø720 mm Ø28/28 520 kg
D74Engine
D74 REMOTE: Stump cutter with remote control, 4WD and diesel engineFSI D74 REMOTE is for the professional user, where stump cutting forms a major part of their daily work.
The powerful 74 HP diesel engine with an impressive torque of 300 Nm at 1500 rpm, the large 720 mm cutter wheel and a work-ing width of 2 m means this machine has incredible capacity. Together with the 4-wheel drive and radio remote control, the D74 Remote is your ideal partner for cutting tree stumps.
All movement and stump cutting operations are controlled via the
radio remote control. The battery charger with an extra battery for the radio and cable for direct connection is included.
The machine is also equipped with an autopilot swing function for optimum cutting capacity. The autopilot adjusts the swing speed based on the engine load. The autopilot optimises capacity and makes it simpler to operate the machine.
Extra equipmentDozer blade and extra cutting depth up to 600 mm.
Product dataEngine . . . . . . . . . . . . . . . . . . . . .55.4 kW/74 HP Kohler - DieselTank capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 l - approx. Wheel drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4WD HydraulicBrakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic
Cutter disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . Ø720 mmTeeth/qty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø28.5/28Dimensions L x W x H . . . . . . . . . . . . . 3200 x 890 x 1510 mmWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1650 kg
• Radio control
• Battery charger
• Cable connection
• 4-wheel drive
• Differential lock
• Twin wheel set
• 2 m working width
• Autopilot on swing
• LED work light
• Tool compartment
• 40 l tank – approx. 15 hours operation
Swing
2000 mm
Height/Depth
600 mm
600 mm
Machine width
890/1520 mm
Chip depth
Max.: 123.5 mm
For more information, visit our website www.fsi.dk
H65• 12–20 ton excavator
• Extra shock-absorbing design
• 3 different engine sizes
H20• 1.5–2.5 ton to 2.0–3.5 ton excavator
• Direct drive
• Supplied with hydraulic hoses
H40• 3–7 ton excavator
• Direct drive
• Supplied with hydraulic hoses
• Extra shock-absorbing design
H52• 8–14 ton excavator
• Direct drive
• Extra shock-absorbing design
Product data Cutting disc
Model Oil flow Max. pressure Motor requirement Diameter Teeth/qty. Weight
H20 30–50 l/minute 250 bar 12–22 kW/15–30 HP Ø370 mm Ø20.5/12 70 kg
H40 50–75 l/minute 250 bar 18–31 kW/25–42 HP Ø470 mm Ø24.5/16 150 kg
H52 80–110 l/minute 300 bar 29–48 kW/40–65 HP Ø570 mm Ø24.5/20 240 kg
H65 100-130 100–130 l/minute 350 bar Max. 76 kW/100 HP Ø720 mm Ø28/28 500 kg
H65 135-160 135–160 l/minute 350 bar Max. 85 kW/115 HP Ø720 mm Ø28/28 500 kg
H65 165-200 165–200 l/minute 350 bar Max. 117 kW/160 HP Ø720 mm Ø28/28 520 kg
Stump cutters for hydraulicsHydraulically driven stump cutter for fitting to an excavator or similar machine, where the machine itself is used to make the swing and up/down movement.
Free choice of cutting direction. The cutting direction can easily be set at 45 degree intervals, in the joint between the unit and the fitting plate for the tool attachment.
The units are supplied with an uncoated top plate, on which an optional tool attachment can be fitted. We also provide a selection of tool attachments.
The machines require a depressurised return to the tank (leak oil).
H20 H40
H52 H65
H20 / H40 / H52 / H65Hydraulic
Chip depth
H20 Max.: 24.5 mm H40 Max.: 52.0 mm H52 Max.: 61.5 mm H65 Max.: 82.5 mm
For more information, visit our website www.fsi.dk
H20S / H40SHydraulic
Hydraulic stump cutters with swingHydraulically driven stump cutters with integrated swing move-ment for fitting to loaders and tool carriers.
The machine is equipped with a bracket to attach the tool attach-ment. We can also provide a finished tool attachment as required.
The swing movement is controlled by two hydraulic cylinders and operation of the swing movement takes place via the electrical box using a mini joystick.
We can also provide HS models for hydraulic control – these are supplied with five hydraulic hoses.
The machines require a depressurised return to the tank (leak oil).
Electrical boxElectrical box with toggle switch and magnet for all HS models
Product data Cutting disc
Power requirements Max. oil flow/pressure Dimension L x W x H Diameter Teeth/qty. Weight
T25 19–41 KW/25–55 HP 35 l/minute, at 150 bar 1750 x 1000 x 1100 mm Ø470 mm Ø20.5/18 240 kg
T27 27–60 kW/35–80 HP 35 l/minute, at 180 bar 2000 x 1350 x 1200 mm Ø470 mm Ø24.5/16 360 kg
T65 53–90 kW/70–120 HP 90 l/minute, at 180 bar 3200 x 1520 x 1700 mm Ø720 mm Ø28/28 700 kg
Product data Cutting disc
Model Oil flow Max. pressure Motor requirement Diameter Teeth/qty. Weight
H20S 30–50 l/minute 250 bar 12–22 kW/15–30 HP Ø370 mm Ø20.5/12 92 kg
H40S 50-75 50–75 l/minute 250 bar 18–31 kW/25–42 HP Ø470 mm Ø24.5/16 200 kg
H40S 80-110 80–110 l/minute 250 bar 29–48 kW/40–65 HP Ø570 mm Ø24.5/16 250 kg
Swing
H20S 700 mm
H40S 1100 mm
Chip depth
H20S Max.: 24.5 mm
H40S Max.: 52 mm
H20S• Direct drive
• Supplied with hydraulic hoses
H40S 50-75• Direct drive
• Supplied with hydraulic hoses
H40S 80-110• Direct drive
• Supplied with hydraulic hoses
For more information, visit our website www.fsi.dk
T25• Hydraulic top link
• Hydraulic joystick
• PTO shaft
• 3-point linkage for cat. 1
• Frame with support legs
T27• Hydraulic extension
• Electrical/hydraulic joystick
• PTO shaft
• 3-point linkage for cat. 1/2
• Adjustable support legs
T65• Hydraulic extension
• Parallel movement of cutting head
• Hydraulic lift of chip guard
• Electrical/hydraulic joystick
• PTO shaft
• 3-point linkage for cat. 1/2
• Adjustable support legs
T25 / T27 / T65Tractor
FSI stump cutters for fitting on tractors with PTOWe provide three strong models in the series of stump cutters designed for using with tractors or similar machines with PTO and 3-point linkage.
The three sizes are adapted for three different classes of tractor for maximum utilisation and efficiency. Operation is executed using the accompanying joystick, which is either fitted on the frame or on another location as required using the bracket supplied.
T27
T25
T65
Product data Cutting disc
Power requirements Max. oil flow/pressure Dimension L x W x H Diameter Teeth/qty. Weight
T25 19–41 KW/25–55 HP 35 l/minute, at 150 bar 1750 x 1000 x 1100 mm Ø470 mm Ø20.5/18 240 kg
T27 27–60 kW/35–80 HP 35 l/minute, at 180 bar 2000 x 1350 x 1200 mm Ø470 mm Ø24.5/16 360 kg
T65 53–90 kW/70–120 HP 90 l/minute, at 180 bar 3200 x 1520 x 1700 mm Ø720 mm Ø28/28 700 kg
Product data Cutting disc
Model Oil flow Max. pressure Motor requirement Diameter Teeth/qty. Weight
H20S 30–50 l/minute 250 bar 12–22 kW/15–30 HP Ø370 mm Ø20.5/12 92 kg
H40S 50-75 50–75 l/minute 250 bar 18–31 kW/25–42 HP Ø470 mm Ø24.5/16 200 kg
H40S 80-110 80–110 l/minute 250 bar 29–48 kW/40–65 HP Ø570 mm Ø24.5/16 250 kg
Swing
T25 1000 mm
T27 1400–1750 mm
T65 1400–2200 mm
Height/Depth
T25 300/400 mm
T27 400/400 mm
T65 600/500 mm
Chip depth
T25 Max.: 41.5 mm
T27 Max.: 43.5 mm
T65 Max.: 82.5 mm
FSI power-tech ApSErhvervsparken 4B7160 Tørring, Denmark
Tel.: +45 75 80 55 58E-mail: [email protected]
www.fsi.dk
Stump cutters for professional usersDanish design and production
Dealer Importer