TM9-1005-229-35DEPARTMENT OF THE ARMY TECHNICAL MANUAL
DS, GS, AND DEPOT MAINTENANCE MANUAL
INCLUDING REPAIR PARTS AND SPECIAL
TOOLS LISTS FOR
SUBMACHINE GUN, CALIBER .45, M3, W/E
(1005-672-1767)
SUBMACHINE GUN, CALIBER .45, M3A1, W/E
(1005-672-1771)
This copy is a reprint which includes currentpages from Change 1.
H E A D Q U A R T E R S , D E P A R T M E N T O F T H E A R M Y
SEPTEMBER 1969
DANGEROUS CONDITIONS
Before starting an inspection, be sure to clear the weapon, Do not actu-ate the trigger until the weapon has been cleared. Inspect the chamber, toinsure that it is empty, and check to see that no ammunition is in positionto be introduced (magazine). Avoid having live ammunition in the vicin-ity of work area.
DANGEROUS SOLUTION
Avoid skin contact with P-C–111. The compound should be washed offthoroughly with running water if it comes in contact with the skin. Agood lanolin base cream, after exposure to compound, is helpful. The useof rubber gloves and protective equipment is recommended.
WARNING
CHANGE
No. 1Changes in Force: C1
TM 9-1005-229-35C1
HEADQUARTERSDEPARTMENT OF THE ARMY
WASHINGTON, DC 2 April 1985
DS, GS, AND DEPOT MAINTENANCE MANUALINCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
SUBMACHINE GUN, CALIBER .45, M3, W/E(1005-00-672-1767)
SUBMACHINE GUN, CALIBER .45, M3A1, W/E(1005-00-672-1771)
TM 9-1005-229-35, 19 September 1969, is changed as follows:
Title is changed as shown above.
Page 3, Paragraph 1-2b, line 8. Change address to read: Commander, US Army Armament,Munitions and Chemical Command, ATTN: AMSMC-MAS, Rock Island, IL 61299-6000.
Page 12, Paragraph 2-14. Change address to read: Commander, US Army Armament, Munitionsand Chemical Command, ATTN: AMSMC-MAS, Rock Island, IL 61299-6000.
Page 31, Repair Parts List. Change SMR codes on figure B-7 as follows:
Item 11,Item 13,Item 14,Item 15,
CAP from PF to PAOZZNUT, PLAIN, ROUND from PF to PAOZZWASHER LOCK from PF to PAOZZOILER from PF to PAOZZ
By Order of the Secretary of the Army:
JOHN A. WICKHAM, JR.General, United States Army
Chief of StaffOfficial:
DONALD J. DELANDROBrigadier General, United States Army
The Adjutant General
Distribution:To be distributed in accordance with DA Form 12-40, Direct and General
Support Maintenance Requirements for Gun, Submachine, Caliber .45, M3, M3A1.
T E C H N I C A L M A N U A L
No. 9-1005-229-35
C HAPTER 1 .Section I.
II.C HAPTER 2 .
S ECTION I.II.
III.
IV.V.
VI.CHAPTER 3 .CHAPTER 4 .APPENDIX A.APPENDIX B.
Section I.II.
III.IV.
*TM 9-1005-229-35
HEADQUARTERS,DEPARTMENT OF THE ARMY
WASHINGTON , D, C., 19 September 1969
DS, GS, AND DEPOT MAINTENANCE MANUAL
INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS
SUBMACHINE GUN, CALIBER .45, M3, W/E
(1005-672-1767)
SUBMACHINE GUN, CALIBER .45, M3A1, W/E
(1005-672-1771)
This manual is current as of 10 May 1969.
INTRODUCTIONGeneral _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Description and data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _ _DIRECT SUPPORT, GENERAL SUPPORT AND DEPOT
MAINTENANCE INSTRUCTIONSRepair parts, special tools, and equipment _ _ _ _ _ _ _ _ _ _ _ _ _ _ Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Preembarkation inspections of material in units alerted for overseas
movement _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _General maintenance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _Removal and installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Depot maintenance procedures _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _REPAIR INSTRUCTIONS _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _FINAL INSPECTION _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ REFERENCES _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT
MAINTENANCE REPAIR PARTS AND SPECIAL TOOLSLIST
Introduction _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Repair Parts List
Repair Parts For:
1-1-1-21-3
2-12–2
2-3-2-52-6-2-122-132-143-1-3-54 - 1 4 - 4A-1 -A-4
B-1 -B-7
Major groups, assemblies and components (figs B-1 and B-2) _ _ _ _ _ _ _ _ _ _ _ _ _ _ Bolt and guide rod group (fig B-3) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Trigger housing group (figs B-4 and B-5) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Trigger and sear group (fig B-6) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Receiver assembly (figs. B-7 and B-8) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Flash hider assembly (fig B-9) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Oiler (fig B-10) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _ _ _ _
Special Tools List (fig B-10) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Index—Federal Stock Number and Reference Number Cross-Reference
to Figure and Item Number _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* This manual supersedes TM 9-1005-229-35, 14 December 1964.
Page
33
78
910, 11
1112
13-171921
23-25
2627232930323334
36
1
Paragraph
TM 9-1005-229-35
CHAPTER 1
lNTRODUCTION
1-1. Scope
These instructions are in accordance with
the maintenance allocation chart published for
the use of direct support, general support, and
depot maintenance personnel maintaining the
Caliber .45, Submachine Guns, M3 and M3A1.
They provide information on the maintenance
of the equipment which is beyond the scope
of the tools, equipment, personnel or supplies
normally available to the operator and orga-
nizational maintenance.
1-2. Forms and Records
a. General. DA forms and procedures usedfor equipment maintenance will be only thoseprescribed in TM 38–750, Army EquipmentRecord Procedures.
b. Recommendation for Equipment Publi-cation Improvements. Report of errors, omis-sions, and recommendations for improving thispublication by the individual user is en-couraged. Reprots should be submitted on DAform 2028 (Recommended Changes to DAPublications) and forwarded direct to: Com-manding General, Headquarters, U. S. ArmyWeapons Command, ATTN: AMSWE–SMM-P, Rock Island, Illinois 61201.
Section II. DESCRIPTION AND DATA
1-3. Description and Tabulated Data views of the submachine gun refer to figures
Refer to TM 9–1005-229-12. For overall 1–1 and 1–2.
3
Section I. GENERAL
TM 9-1005-229-35
Figure 1-1. Caliber .45 Submachine Gun M3 wlFlash Hider Assembly,M9-right front view.
4
TM 9-1005-229-35
Figure 1-2. Caliber .45 Submachine Gun M3A1 w/Flash Hider Assembly,M9-right front view.
5
TM 9-1005-229-35
CHAPTER 2
DIRECT SUPPORT, GENERAL SUPPORT AND
DEPOT MAINTENANCE INSTRUCTIONS
Section I. REPAIR PARTS, SPECIAL TOOLS, AND EQUIPMENT
2-1. Repair Parts, Special Tools and Equipment
Refer to appendix B and table 2–1.
Table 2-1. Special Tools and Equipment
Item
Trigger pull measur-ing fixture
Identifying Reference
Fig Para
7274758 2-1 3-4
Use
To measure trigger pull pressure.
7
number
TM 9-1005-229-35
2-2. General
Figure 2-1. Trigger pull measuring fixture.
Section II. TROUBLESHOOTING
Refer to TM 9-1005-229-12 and table 2-2.
Table 2-2. Troubleshooting
Malfunction
1. Failure to feed
2. Failure to fire
3. Failure to extract
8
Probable cause
Defective magazine catchspring
a. Worn or brokenb. Bent guide roda. Pitted chamber
firing pin
b. Broken extractor
Corrective action
Replace spring
Replace bolt (6 or 8, fig B-3)Straighten guide rodReplIaceReplace
barrelextractor
Malfunction
4. Failure to eject
5. Failure to cock6. Miscellaneous:Excessive pull required to
extract bolt.
Magazine catch will not depress.
Difficulty encountered wheninserting magazine assembly,
TM 9-1005-229-35
Table 2-2. Troubleshooting—Continued.
Probable cause
Broken ejector
Worn sear notch
a. Dented receiverb. Bent or burned guide rods
c. Ejector binding in slot ofbolt
Magazine catch assembledwrong.
Bent or burned receiver atmagazine well.
Corrective action
Replace (2, fig B-4 and 12,fig B-5).
Replace bolt. (6 or 8, fig B-3)
a. Repairb. Repair rods. Remove burs
(Para 2-12)c. Repair ejector (table 3-1).
Remove and assemble properly,
Remove burs and straighten.
Section III. PREEMBARKATION INSPECTIONS OF
MATERIEL IN UNITS ALERTED FOR OVERSEAS MOVEMENT
2-3. Preparation
a. Cleaning. All metal parts shall bethoroughly cleaned (para 2–9). Surfaces ofparts subjected to burned powder residue willbe cleaned with rifle bore cleaning compound(CR).
b. Preservation. All metal surfaces shall becoated with a preservation oil.
2-4. Shipping Instructions
When shipping the submachine gun, the of-ficer-in-charge of preparing the shipment willbe responsible for properly processing the ma-teriel for shipment, including the preparationof Army shipping documents.
2-5. Inspection Procedures
Refer to TB 9-1000-247-35 and table 2-3
Table 2-3. Preembarkation Inspection Procedures
Item
Barrel
Inspection criteria
Preliminary InspectionInspect the weapon as a unitfor general appearance andconditionGeneral InspectionTo determine serviceability:A barrel that is uniformly pittedwith the edges of the lands sharpis acceptable. Only those barrelsshowing developed pits, or pitscutting into the lands, are un-
Table 2–3. Preembarkation InspectionProcedures—Continued.
Item
Bolt assembly
Sear assembly
Safety
EjectorCocking lever
Oiler
Components
Barrel lockMiscellaneous
Inspection criteria
satisfactory. Ringed bores orringed sufficiently to bulge theoutside surface are cause forrejection.Check to see that the bolt slidesf reel y with in the receiver.Check to see that the sear holdsthe bolt firmly in the cockedposition and releases the boltproperly when the trigger isactuated.With the weapon cocked (thebolt must not move forwardas the trigger is squeezed.Check for missing ejector.Check the M3 for functioningof the cocking lever.Check the M3A1 to make certainlock washer is present in theoiler.Inspect for defects in metalcomponents.
Note. Minor defects in metal com-ponents do not normally affecttheir being acceptable.
Check functioning of barrel lock.Check to see that all authorizedmodifications have been applied,and that no unauthorized altera-tions have been made. Check theindex in DA Pam 310–7 and thecurrent MWO files for any MWO’sprinted after publication.
9
TM 9-1005-229-35
Table 2-3. Preembarkation InspectionProcedures—Continued.
Item Inspection criteria
Make certain that no work beyondthe scope of the unit is beingattempted.Instruct personnel in properpreventive maintenance procedures, where found inadequate.Check legibility of serial number.Overall
Table 2-3. Preembarkation InspectionProcedures—Continued.
Item Inspection criteria
Metal surfaces A worn surface is objectionablefrom the standpoint of visibilitywhen it is capable of reflectinglight. Check to see that all rearsights have a dull black or grayfinish on all surfaces.
Section IV. GENERAL MAINTENANCE
2-6. General
This section provides the necessary instruc-tions on the general maintenance procedures.Operating instructions are contained in TM9-1005-229-12.
2-7. General Repair Methods
a. Disassembly and Assembly Procedures.(1) In disassembling a unit, remove the
major assemblies whenever possible. Subas-semblies may be disassembled, as necessary,into individual parts.
(2) During assembly, subassembliesshould be assembled first and then install toform a complete unit.
(3) Complete disassembly of a unit is notalways necessary in order to make a requiredrepair or replacement, Good judgment shouldbe exercised to keep disassembly and assemblyoperations to a minimum.
b. Replacement of Parts.(1) When assembling a unit, replace pins,
if damaged. Replace oiler nut or oiler ifthreads are damaged,
(2) All springs will be replaced if theyare broken, bent, cracked, or fail to functionproperly.
(3) If a required new part is not avail-able, reconditioning of the old part is required.Such parts should be examined carefully afterreconditioning to determine their serviceabili-ty.
c. Use of Tools.(1) Care must be exercised to use tools
that fit and are suitable for the task to be
10
performed in waler to avoid unnecessarylation of parts and/or damage to tools.
(2) Keep tools clean and work with
muti-
cleanparts. Normal rules of good housekeepingmust be observed.
2-8. Cleaning
a. After repair operations and prior to as-sembly, all parts should be cleaned thoroughlyof all grease, oil, water and dirt using drycleaning solvent (SD). They should be driedthoroughly with clean wiping cloths and coatedwith PL special to prevent rusting.
b. Clean burned powder residues from thebarrel bore with rifle bore cleaning compound(CR) using stock extension 7161812 withcleaning brush 5504036. After cleaning withbrush place several cleaning rod patches on endof extension and run through bore of barrelseveral times to clean and dry thoroughly.
c. Clean the chamber using rifle bore clean-ing compound (CR) and cleaning brush 610-8828; wipe dry after cleaning.
d. Apply a light coat of general purposelubrication oil (PL special) to oil exterior sur-faces and the bore to prevent corrosion.
e. On components that contain an accumula-tion of light rust, use a clean cloth moistenedwith rifle bore cleaning compound (R), If thisdoes not suffice, use crocus cloth. Make certainit does not scratch or alter the finished sur-faces. Remove all dirt and residue; oil surfacesbefore assembling parts.
f. On component parts such as the barrel,bolt and guide rod group, which contain ahard carbon residue it is necessary to cleanthese items with carbon removing compound,P–C–111, as follows:
TM 9-1005-229-35
Warning. Avoid skin contact. The compoundshould be washed off thoroughly with run-ning water if it comes in contact with theskin. A good lanolin base cream, after expos-ure to compound, is helpful. The use of glovesand protective equipment is recommended.
(1) Using a suitable container, fill withfresh compound.
(2) Before soaking a component in com-pound, remove grease, dirt, and oil. Place partsto be cleaned in container, making certain theyare completely immersed.
(3) Soak for 2 to 16 hours. Remove partsand allow to drain. Rinse with water or sol-vent. To effectively remove carbon, brush withstiff bristle brush under running water. Allowto dry, then apply a light coat of general pur-pose lubricating oil (PL special).
g. New materiel and component parts re-ceived from storage for immediate use mayhave heavy accumulations of grease, Removethis residue with waste or clean wiping clothssaturated with dry cleaning solvent (SD). Dryand lubricate as specified in paragraph 2—13
h. For general cleaning instructions on allparts, refer to TM 9–208–1.
2-9. General Precautions in Cleaning
a. Dry cleaning solvent is flammable andshould not be used near an open flame. Fireextinguisher should be readily available whenusing this material. In addition, this materialevaporates quickly and has a drying effect onthe skin. When used without rubber gloves, itrelay cause cracks in the skin, and in the easeof same individuals, a mild irritation or in-flammation. Use only in well-ventilated places.
b. The use of diesel fuel oil, gasoline orbenzene (benzol) for cleaning the weapon isprohibited.
c. Store rifle bore cleaning compound (CR)in a warm place, if practical. Do not dilute oradd anti freeze.
2-10. Finished Surfaces
All treated surfaces will be refinished tomatch the appearance of new parts.
Note. Sandblasting is permissible on nonworking sur-faces for removal of dirt and rust.
2-11. Removal of Burs From Threads andWorking Surfaces
a. During the entire life of the submachinegun, polishing and stoning are necessary torelieve friction and to remove burs caused byusage. Burs on threads and like surfacesshould be removed with a fine stone, tap orthread chaser. Burs on such working surfacesas the receiver, guide rods, cam surfaces, andreceiver housing area should be removed witha fine stone and polished with crocus cloth.
Caution. Care should be observed to stoneevenly and lightly and not remove more metalthan absolutely necessary to maintain correctcontours. Critical dimensions of parts or as-semblies must not be altered in any way thatwould affect the functioning or interchange-ability of parts.
b. Rough spots, scores, galling, and gougeswill be smoothed to enable the part to operatenormally. The finish of the repaired componentwill be approximate of the original finish.
2-12. Lubrication
Make certain all parts are cleaned and driedthoroughly and lubricated by applying a lightcoat of general purpose lubricating oil (PLspecial).
Section V. REMOVAL AND INSTALLATION
2-13. General groups and assemblies refer to TM 9-1005-
For removal and installation of major 229-12 and figures B–1 and B–2.
11
TM 9-1005-229-35
Section VI. DEPOT MAINTENANCE PROCEDURES
2-14. General depot maintenance of this materiel will be fur-nished by contacting, Commanding General,
Depot maintenance procedures are similar Headquarters, U. S. Army Weapons Command,to those pertaining to direct and general sup- ATTN: AMSWE-SMM-SA, Rock Island,port maintenance. However, further details on Illinois 61201.
12
TM 9-1005-229-35
CHAPTER 3
REPAIR INSTRUCTIONS
3-1. General
This chapter provides specific instructionsfor guidance during inspection and repair bydirect and general support maintenance of ma-teriel in the hands of troops in the field, indirt and general support shops, and inalerted units scheduled for oversea duty. In-spections are made for the purpose of: (1)determine the condition of an item as to serv-iceability, (2) recognizing conditions thatwould cause failure, (3) assuring proper ap-plication of maintenance policies at prescribedlevels, and (4) determine the Ability of a unitto accomplish its maintenance and supply mis-sion
3-2. Disassembly/Assembly of Major Groupsand Assemblies
a. Magazine Assembly, Barrel and GunStock Extension. Refer to TM 9-1005-229-12.
b. Bolt and Guide Rod Group. Refer tofigure B-3.
c. Trigger Housing Group. Refer to figuresB-4 and B-5.
d. Trigger and Sear Group. Refer to figureB-6.
e. Receiver Assembly. Refer to figures B-7and B-8.
f. Flush Hider Assembly. Refer to figureB-9.
3-3. Cleaning, Inspection, and RepairInstructions
a. Refer to paragraph 2-9 for cleaning in-structions.
b. Refer to table 3-1 for inspection and re-pair procedures.
c. Complete inspection of all parts is notalways necessary, good judgment should be ex-ercised pertaining to the degree of inspectionof integral parts within assemblies.
Table 3-1. Inspection and Repair Procedures
Item
Magazine:
Inspection
Note. On the new magazines thebase is spot welded to the bodyand disassembly of the magazine,in this case, is not authorized.
Inspect base for deformation orwear.
Inspect base for burs.
Inspect spring for cracks, weaktension and set.
Inspect follower for wear.
Inspect follower for burs.
Repair
Replace magazine (1, figs B-1and B-2) if components areworn, broken or damaged.
Remove burs as described inparagraph 2-11.
Replace magazine (1, figs B-1and B-2) if spring is cracked,set or tension weak.
Replace magazine if follower isworn, broken or damaged.
Remove burs as described in para-graph 2-11.
13
TM 9-1005-229-35
Table 3-1. Inspection and Repair Procedures-Cont.
Item
Gun stock extension:
Barrel
Bolt and guide rod group:
Inspection
Inspect the body for dents, cracks,and fit in receiver.
Inspect for deformation andwear.
Inspect for burs.
Examine barrel bore for wear,pits and bulges.
Check serrations on barrel collarfor wear and damage.
Inspect the collar; make certainit is secure to the barrel.
Inspect guide rod retaining clipfor wear and damage.
Inspect guide rod locating plate;make certain it is not bent orburred at the holes.
Inspect extractor pin for wearand damage.
Check to see that the extractoris clean and free of carbon,is not worn and does not bindin bolt.
Check the bolt for wear andburs. Check the firing pinpoint; make certain it is notworn as to cause misfiring.
Inspect the guide rods to see thatthey are straight, smooth andare secured firmly to thelocating plate.
Inspect the driving springs forfunction, cracks and set.
Note. Some bolts 5653429, for theM3 Submachine Gun have theletter "H" stamped on the sur-face indicating they were ofearly manufacture and wereheat treated to increase thehardness. However, all boltsnow in use are serviceable,whether or not they have theletter “H” stamped on the sur-face.
Repair
Replace magazine if body isdamaged.
Replace stock extension (2, figsB-1 and B-2) if damaged.Straighten if bent.
Remove burs.
Replace barrel (3, figs B-1 andB-2) if lands are worn as toaffect the accuracy of theweapon. Replace barrel, if pitsare as wide as lands or aremore than three-eights of aninch long.
Replace barrel if threads arestripped or if serrations areworn affecting the security ofbarrel to the receiver.
Replace the barrel if collar is notsecure. Remove burs as in-dicated in paragraph 2-11.
Replace worn or damaged re-taining clip (1, fig B-3).
Replace worn or bent locatingplates (2, fig B-3).
Replace worn or damaged pin(4, fig B-3).
Replace worn or damaged ex-tractor (5, fig B-3).
Replace bolts (6 or 8, fig B-3)that contain worn firing pins.
Replace bolt if sear notch ischipped or worn.
Straighten guide rods if bent.Replace guide rods (9, figB-3) if rods are not secureto locating plate.
Replace springs (10, fig B-3)if cracked, weak or set.
14
TM 9-1005-229-35
Table 3-1. Inspection and Repair Procedures-Cont.
Item
Housing group:
Trigger and sear group:
Receiver assembly:
Inspection
Inspect all parts for damageand wear which might causemalfunction. Inspect for burs,rust, foreign matter in recesses,deformation, and free actionwith mating parts
Inspect housing for deformationand dents.
Inspect ejector for looseness,damage, and binding in slotof bolt (M3 only).
Function the retracting handleto see that the retracting leverpawl is caromed down and thelever rotated forward is bythe action of the retractinglever pawl spring.
Inspect the spring for distortion,set, and tension. Check to seethat the retracting lever pawlstop is not worn.
Inspect the retracting handle forburs, wear, rust, and contactingside of receiver.
Inspect the retracting leverspring for function, fracture,and set. Check ends; makecertain they are not bent orbroken.
Inspect the retracting lever pawlspring for bends, distortion,and if it is secure.
Inspect the oiler clip of thehousing for wear, damage, andlooseness of housing.
Inspect sear for wear and burs.
Inspect trigger spring for function,cracks, and set.
Inspect the trigger and conectorfor dents, deformation andfunctioning. Make certainthe connector rotates on therivet.
Inspect the collar for burs andwear.
Inspect the catch for functioning,wear, and damage.
Inspect spring for cracks, tension,and set.
Repair
Replace all broken, worn, andunserviceable parts. Removeburs and rust as indicatedin paragraph 2-11.
Straighten dents, replace if notrepairable,
Straighten point of ejector ifejector is bent and binds inbolt.
Replace spring (6, fig B-5).Replace lever assembly (4,fig B-5) if pawl stop isworn.
Replace if broken or worn;remove burs and rust asindicated in paragraph 2-11.
Replace spring (3, fig B-5) ifbroken, worn or unserviceable.
Replace spring (6, fig B-5) ifbroken, worn or unserviceable.
Replace clip (10, fig B-5),if damaged
Remove burs from sear (para-graph 2-11). Replace sear(2, fig B-6) if worn or cracked.
Replace spring (4, fig B-6) ifcracked or set or if tensionis weak.
Remove dents from trigger searconnector; replace (6, fig B-6)if damaged or worn.
Replace collar (2, figs B-7 andB-8) if worn. Remove burs(para 2-11).
Replace catch (3, figs B-7 andB-8) if worn or damaged.Replace spring (4, figs B-7and B-8) if cracked, set ortension is weak.
15
TM 9-1005-229-35
Table 3-1. Inspection and Repair Procedures-Cont.
Item
Receiver assembly-cont.
Inspection
Inspect for worn, or bentretaining-pin.
Inspect pin for burs and wear.
Inspect the cover to see if itoperates freely and is securedfirmly to recesses, Inspect forloose rivets and make certainthe safety is not worn.
Inspect the cover spring. Makecertain it retains the coverand is not worn, burred anddeformed and that it issecurely retained by the rivets.
Inspect the retaining strap, makecertain it is secured to thereceiver.
Inspect the ratchet spring fortension, retaining action withbarrel, and for wear. Checkto see that it is riveted securelyto the receiver (fig 3-1).
Inspect the barrel bushing fordamaged or stripped threads.
Inspect the weld inside receiver;make certain it does notinterfere with the movement ofthe bolt.
Inspect the receiver for dentsor cracks.
Repair
Replace pin (1, figs B-7 andB-8) if bent or worn.
Remove burs (para 2-11), replaceif bent or worn.
Replace rivets (7, figs B-7 andB-8) on cover assembly ifloose.
Note. To install cover spring,insert the two 1/8 x 3/16flathead solid rivets, with theheads on the inside of thereceiver. Place the cover springon the rivets and positionthe receiver on an improvisedriveting anvil. Peen the endsof the rivets with a ball peenhammer and drift punch untilthe ratchet spring is secure.
Replace cover spring (8, fig B-7and 9, fig B-8), if weak orloose on receiver.
Replace retaining strap (9, figB-7 and 10, fig B-8) if loose,broken, or missing.
Replace ratchet spring (10, figB-7 and 11, fig B-8) if crackedor tension is weak. Replacerivets (7, figs B-7 and B-8).To install the ratchet spring(10, fig B-7 and 11, fig B-8)insert two 1/8 x 3/16 flat-head solid rivets, with theheads on the inside of thereceiver. Place the ratchetspring on the rivets andposition the receiver on theimprovised riveting anvil.Peen the ends of the rivetsuntil the ratchet spring issecure.
Replace weapon if barrelbushing has stripped threads.
Replace weapon if welds interferewith movement of bolt or ifcracked.
If receiver is bent or dentedso as to restrict the movementof the bolt, it will be declaredunserviceable.
16
TM 9-1005-229-35
Table 3-1. Inspection and Repair Procedures-Cont.
Item
Receiver assembly - Cont.
Flash hider assembly:
Inspection
Inspect oiler cap and nut onSubmachine Gun M3A1 forwear or stripped threads andthe oiler for evidence of leaksor stripped threads.
Inspect magazine well of receiverfor burs or being bent.
Inspect the wing nut for strippedthreads and damage.
Inspect washer for wear anddamage.
Inspect the setscrew for strippedthreads, burs and wear.
Inspect the flash hider for dents,deformation, and cracks.
Inspect ring of flash hider,make certain it is welded toflash hider.
3-4. Trigger Pull Test
After final assembly of the submachinegun, check the trigger pull using trigger pullmeasuring fixture 7274758 (fig. 2-1) in ac-cordance with instructions indicated below.
Figure 3-1. Checking spring action of ratchet spring.
Repair
Replace oiler cap (11, fig B-7)nut (13, fig B-7) if worn orif threads are stripped.Replace oiler (15, fig B-7)if it leaks or has strippedthreads.
Remove burs in receiver well(para 2-11). Replace receiverif dents in magazine wellcannot be fixed so as not toimpede magazine.
Replace wing nut (1, fig B-9)if threads are stripped ordamaged.
Replace washer (2, fig B-9)if worn or damaged.
Replace setscrew (3, fig B-9)if threads are stripped ordamaged.
Replace flash hider (6, figB-9) if cracked or dented.
Replace flash hider (6, fig B-9)if ring is loose on flash hider.
Step 1. With the safety unlocked, rest theweight on the floor and hook the notched por-tion of the rod over the center portion of thetrigger.
Note. Make certain the rod does not contact or rubany portion of the submachine gun and that rod andbarrel are parallel.
Step 2. Carefully raise the weight from thefloor. When using less than the 4 poundweight (minimum), the trigger should notfall. When using the 7.5 pound weight (maxi-mum), the trigger should fall.
Caution. A slow and steady lift must beutilized to assure a true and accurate check.
3-5. Correcting Trigger Pull
Caution. While stoning, critical dimensionsshould not be altered.
Refer to table 3–2 for trigger pull correctionprocedures.
17
TM 9-1005-229-35
Table 3-2. Trigger Pull Correction Procedures
Malfunction Probable cause
Trigger pull too light
Trigger pull too heavy
Worn searWorn sear notchBurred sear
Burred sear notch
Corrective action
Replace sear (2, fig. B-6).Replace bolt (6 or 8 fig. B-3).Stone searReplace sear (2, fig B-6).Stone sear notch on bolt, replace
bolt.
18
TM 9-1005-229-35
CHAPTER 4
FINAL INSPECTION
4-1. General
Final inspection is performed on the ma-teriel, after repair has been completed, to de-termine that the weapon meets serviceabilityrequirements prescribed in the repair instruc-tions, chapter 3. In performing final inspec-tion, the inspector will make certain that allrepairs have been completed and that theweapon is intact and that all components andassemblies are secure and function properly.Listed below are specific inspection proceduresto be followed during this inspection.
4-2. Visual Inspection Procedures
a. Inspect the magazine, make certain it isretained securely to the gun.
b. Inspect the barrel, see that it is securedtightly to the receiver.
c. Inspect the hewing group, make certainit is secure to the receiver.
d. Check the trigger pin and sear pin, seethat they are retaining the trigger and seargroup within receiver.
e. Inspect sight, make certain it is not bentor distorted.
f. Check over–all appearance of the gun.The metal finish should range from a denseblack to a medium light gray. Sight must havea dull black or gray finish.
4-3. Functional Inspection
a. Acutate magazine catchtion.
for proper func-
b. Check functioning of trigger.c. Acutate stock catch, make certain it works
in conjunction with stock.d. Function cover assembly, see that it snaps
in closed position on receiver and safety holdsbolt in locked position.
e. Check trigger with trigger pull meas-uring fixture 7274758 (fig. 2–1). Refer toparagraph 3-4.
f. Trigger pull can be corrected by the se-lective assembly of related parts. Refer to table3-2.
4-4. Hand Function
Following repair, hand function submachinegun. Weapons which fail to function properlyare to be corrected by the replacement of de-fective component or by performing such re-pair as required.
19
TM 9-1005-229-35
APPENDIX A
REFERENCES
A-1. Publication Indexes
The following indexes should be consulted frequently for the latest changes or revisions ofreferences given in this appendix and for new publications relating to materiel covered in thistechnical manual.
Index of Army Films, Transparencies, GTA Charts, and RecordingsMilitary Publications:
Index of Administrative PublicationsIndex of Blank FormsIndex of Doctrinal, Training, and Organizational PublicationsIndex of Supply Catalogs and Supply Manuals (excluding types
7, 8, and 9)Index of Technical Manuals, ‘Technical Bulletins, Supply Manuals
(types 7, 8, and 9), Supply Bulletins, and Lubrication OrdersU.S. Army Equipment Index of Modification Work Orders
A-2. Supply Catalogs
Tool Set, Direct and General Support Maintenance, Basic Small Arms(FSN 4933-775-0366)
Operator’s and organizational Maintenance Manual Including RepairParts and Special Tools List for Submachine Guns, Caliber .45,M3 and M3A1
A-3. Forms
The following form pertains to the materiel.
DA Pam 108–1
DA Pam 310-1IDA Pam 310-2DA Pam 310-3DA Pam 310-6
DA Pam 310-4
DA Pam 310-7
SC 4933-95-CL-E04
TM 9-1005-229-12
DA Form 2028, Recommended Changes to DA Technical Manual, Parts List or Supply Manual;7,8, and 9.
A-4. Other Publications
a. General The following explanatory publications contain information pertinent to this ma-teriel and associated equipment.
Logistics (General):Malfunctions Involving Ammunition and Explosives AR 700-1300-8Army Equipment Record Procedures TM 38-750
Military Terms, Abbreviations, and Symbols:Authorized Abbreviations and Brevity Codes AR 320-50Dictionary of United States Army Terms (short title: AD) AR 320-5
21
TM 9-1005-229-35
Military SymbolsMilitary Training ManagementSafety: Accident Reporting and RecordsSubmachine Guns, Caliber .45, M3 and M3A1Techniques of Military Instructions
b. Inspection and Maintenance.Command Maintenance Management Inspections Issue of Suppliesand Equipment;
Requisitioning, Recept, and Issue SystemMaintenance of Supplies and Equipment:
Organization, policies, and responsibilities for maintenanceoperations
Ordnance Maintenance:Cleaning of Ordnance Materiel
FM 21-30FM 21-5AR 385-40FM 23-41FM 21-6
AR 750-8
AR 725-50
AR 750-5
TM 9-208-1
22
TM 9-1005-229-35
APPENDIX B
DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT
MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST
Section I. INTRODUCTION
B-1. Scope
This appendix lists repair parts and specialtools required for the performance of directsupport, general support, and depot mainte-nance of the Caliber .45, Submachine Guns,M3 and M3A1.
B-2. General
This repair parts and special tools list isdivided into the following sections:
a. Repoir Parts—Section II. A list of repairparts authorized for the performance of main-tenance at the direct support, general sup-port, and depot level in figure and item num-ber sequence.
b. Special Tools, Test and Support Equip-ment—Section III. A list of special tools, testand support equipment authorized for the per-formance of maintenance at the direct support,general support, and depot level.
c. Federal Stock Number and ReferenceNumber Index—Section IV. A list of Federalstock numbers in ascending numerical sequencefollowed by a list of referenced numbers inascending alpha–numeric sequence, cross ref-erenced to the illustration figure number anditem number.
B-3. Explanation of Columns
The following provides ancolumns in the tabular lists inIII:
a. Source, Maintenance, andCodes (SMR), Column 1.
explanation ofsections II and
Recoverability
(1) Source codes, indicatestatus and source for the listedcodes used are:
the selectionitem. Source
codeP
P2
M
A
X
X1
X2
G
Explanation
Repair parts which are stocked in or sup-plied from the GSA/DSA, or army supplysystem, and authorized for use at indicatedmaintenance categories.Repair parts which are procured and stockedfor insurance purposes because the combator military essentiality of the end itemdictates that a minimum quantity be avail-able in the supply system.Repair parts which are not procured orstocked but are to be manufactured at indi-cated maintenance levels.Assemblies which are not procured or stockedas such but are made up of two or moreunits. Such component units carry individualFSN’S and descriptions, are procured andstocked separately and can be assembled toform the required assembly at indicatedmaintenance categories.Parts and assemblies which are not pro-cured or stocked and the mortality of whichis normally below that of the applicable enditem or component. The failure of such partor assembly should result in retirement ofthe end item from the supply system.Repair parts which are not procured orstocked. The requirements for such itemswill be filled by use of the next higher as-sembly or component.Repair parts which are not stocked. Theindicated maintenance category requiringsuch repair parts will attempt to obtainthrough cannibalization; if not obtainablethrough cannibalization, such repair partswill be requisitioned with supporting justi-fication through normal channels.Major assemblies that are procured withPEMA funds for initial issue only to be usedas exchange assemblies at DSU and GSUlevel. These assemblies will not be stockedabove DSU and GSU level or returned toDepot supply level.
(2) Maintenance codes, indicate thelowest maintenance category authorized to in-
23
TM 9-1005-229-35
stall the repair part. The maintenance levelcodes are:
Code Maintenance CategoryC Operator or CrewO OrganizationalF Direct SupportH General SupportD Depot
(3) Recoverability codes, indicate wheth-er unserviceable repair parts/or tools and testequipment will be returned for recovery orsalvage. Items not coded are expendable. Re-coverability codes are:
Code Recoverability Aspect
R Applied to repair parts (assemblies andcomponents), special tools and test equipmentwhich are considered economically repairableat Direct and General support maintenancelevels. When the item is no longer repair-able, it is normally disposed of at the GSlevel. When supply considerations dictate,some of these repair parts may be listed forautomatic return to supply for Depot levelrepair as set forth in AR 710–50. When solisted, they will be replaced by supply on anexchange basis.
S Repair parts and assemblies which are eco-nomically repairable at DSU and GSU ac-tivities and normally are furnished by supplyon an exchange basis. When items are de-termined by a GSU to be uneconomicallyrepairable, they will be evacuated to a depotfor evaluation and analysis before final dis-position.
T High dollar value recoverable repair partswhich are subject to special handling andare issued on an exchange basis. Such repairparts are normally repaired or overhauledat Depot maintenance activities.
U Repair parts specifically selected for salvageby reclamation units because of preciousmetal content, critical materials, high dollarvalue, reusable casings, or castings.
No Code Parts will be con-Indicated sidered expendable.
b. Federal Stock Yumber, Column 2. Thiscolumn indicates the Federal stock number as-signed to the item and will be used for re-quisitioning purposes.
c. Descriptionf Column 3. This column in-dicates the Federal item name and any addi-tional description of the item required. Theabbreviation “w/e“ when used as a part ofthe nomenclature, indicates the Federal stock
number includes all armament, equipment, ac-cessories, and repair parts issued with the item.A part number or other reference number isfollowed by the applicable five-digit Federalsupply code for manufacturers in parentheses.
d. Unit of Measure (U/M), Column 4. A2 character alphabetic abbreviation indicatingthe amount or quantity of the item upon whichthe allowances are based, i.e., ft, ea, pr, etc.
e. Quantity Incorporated in Unit, Column5. This column indicates the quantity of theitem used in a functional group or assembly.A “V” appearing in this column in lieu of aquantity indicates that a definite quantity can-not be indicated (e.g., shims, spacers, etc.).
f. 30–Day DS/GS Maintenance Allowances,Columns 6, and 7.
Note. Allowances in GS column are for GS mainte-nance only.
(1) The allowance columns are dividedinto three subcolumns. Indicated in each sub-column, opposite the first appearance of eachitem, is the total quantity of items authorizedfor the number of equipments supported. Sub-sequent appearances of the same item willhave the letters “REF” in the applicable allow-ance columns. Items authorized for use as re-quired but not for initial stockage are identi-fied with an asterisk in the allowance column.
(2) The quantitative allowances for DS/GS levels of maintenance will represent initialstockage for a 30–day period for the numberof equipments supported.
(3) Determination of the total quantityof parts required for maintenance of more than100 of these equipments can be accomplishedby converting the equipment quantity to a dec-imal factor by placing a decimal point beforethe next to last digit of the number to indicatehundredths, and multiplying the decimal factorby the parts quantity authorized in the 51-100allowance column. Example, authorized allow-ance for 51-100 equipments is 40; for 150equipments multiply 40 by 1.50 or 60 parts re-quired,
g. 1–Year Allowances Per 100 Equipments/Contingency Planning Purposes, Column 8.This column indicates opposite the first ap-pearance of each item the total quantity re-
24
quired for distribution and contingency plan-ning purposes. The range of items indicatestotal quantities of all authorized items requiredto provide for adequate support of 100 equip-ments for one year.
h. Depot Maintenance Allowance Per 100Equipments, Column 9. This column indicatesopposite the first appearance of each item, thetotal quantity authorized for depot mainte-nance of 100 equipments. Subsequent appear-ances of the same item will have the letters“REF” in the allowance column. Items au-thorized for use as required but not for initialstockage are identified with an asterisk in theallowance column.
i. Illustration, Column 10. This column isdivided as follows:
(1) Figure Number, Column 10a. Indi-cates the figure number of the illustration inwhich the item is shown.
(2) Item Number, Column 10b. Indicatesthe callout number used to reference the itemin the illustration.
B-4. Special Information
a. Identification of the usable on codes in-cluded in column 3 of this publication are:
Code Used onNo code M3 and M3A1
A M3 OnlyB M3A1 Only
b. The following publications pertain to theSubmachine Gun, Caliber .45, M3 and M3A1and their components.
FM 23-41
TM 9-1005-229-12
Submachine Guns, Caliber .45,M3 and M3A1Operator’s and OrganizationalMaintenance Manual includingBasic Issue Items List, RepairParts and Special Tools List.
B-5. How to Locate Repair Parts
a. When Federal stock number or referencenumber is unknown:
(1) First. Using the table of contents, de-termine the functional group or assembly with-in which the repair part belongs. This is neces-sary since illustrations are prepared for func-tional groups or assemblies and listings aredivided into the same groups.
TM 9-1005-229-35
(2) Second. Find the illustration coveringthe functional group or assembly to which therepair part belongs.
(3) Third. Identify the repair part on theillustration and note the illustration figureand item number of the repair part.
(4) Fourth. Using the Repair Parts List-ing, find the functional group or assembly towhich the repair part belongs and locate theillustration figure and item number noted onthe illustration.
b. When Federal stock number or referencenumber is known:
(1) First. Using the Index of FederalStock Numbers and Reference Numbers findthe pertinent Federal stock number or refer-ence number. This index is in ascending FSNsequence followed by a list of reference num-bers in ascending alpha-numeric sequence,cross–referenced to the illustration figure num-ber and item number.
(2) Second. Using the Repair Parts List-ing, find the functional group or assembly ofthe repair part and the illustration figurenumber referenced in the Index of FederalStock Numbers and Reference Number.
B-6. AbbreviationsAbbreviations Explanation
ANLD _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ annealedCARB _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _carbonCK _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ countersunkDLD _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _drillededFL-HD _ _ _ _ _ _ _ _ _ _ _ _ _ _ flat headID _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ inside diameterNC _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Americal National
threadNF _ _ _ _ _ _ _ _ _ _ _ __ _ _ _Americal National
threadOD _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _outside diameterOV.4L-HD_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ oval headPHOS-CTD _ _ _ _ _ _ _ _ _ _ _ _ _phosphate-coatedRD _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ roundS _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _stielSHK _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _shankSYNTH–RBR _ _ _ _ _ _ _ _ _synthetic rubber
B–7. Federal Supply Codes forManufacturers
Code00000 ----19204 ----19205 ----81580 ----96906 ----
ManufacturerOrdnance CorpsRock Island ArsenalSpringfield ArmoryMcCulloch CorporationMilitary Standard
course
fine
25
TM
9-1005-229-35
26
TM
9-1005-229-3527
TM
9-1005-229-35
28
TM
9-1005-229-3529
TM
9-1005-229-35
30
TM
9-1005-229-35
31
TM
9-1005-229-35
32
TM
9-1005-229-35
33
TM
9-1005-229-35
34
TM
9-1005-229-35
35
TM 9-1005-229-35
36
Figure B-1. Submachine Gun, Caliber .45, M3A1 only- major groups,assemblies and components.
Figure B-2. Submachine Gun, Caliber .45, M3 only-major groups,assemblies and component.
37
TM 9-1005-229-35
TM 9-1005-229-35
Figure B–3. Bolt and guide rod group, M3 and M3A1-exploded view.
TM 9-1005-229-35
Figure B–4. Trigger housing group, M3A1 only-exploded view.
Figure B-5. Trigger housing group, M3 only—exploded view.
TM 9-1005-229-35
4 0
TM 9-1005-229-35
41
Figure B-6. Trigger and sear group, M3 and M3A1-exploded view.
TM 9-1005-299-35
Figure B-7. Receiver assembly, M3A1 only-exploded view.
42
TM 9-1005-229-35
Figure B-8. Receiver assembly, M3 only—exploded view.
43
TM 9-1009-299-35
44
Figure B-9. Flash hider assembly-exploded view.
Figure B-10. Tools and equipment
45
TM 9-1005-229-35
TM 9-1005-229-35
Stock Number1005-200-5864
1005-209-9755
1005-288-35651005-519-64561005-534-99251005-534-9927
1005–534–99311005–534–99321005-534-9942
1005-534-9947
1005-535-11911005-535-11951005-535-11961005-535-12101005-555-71521005-555-97381005-556-43641005-565-3427
1005-565-34291005–565-34311005–565-34321005–610-88281005-630-14481005-630-14491005-630-14521005-630-1453
1005-630-1456
1005-630-14641005-630-14691005-630-14741005-716-0997
Section IV. INDEX -FEDERAL STOCK NUMBER AND REFERENCE
NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBER
Figure No.B-1B–2B-7
B-10B-10
B-7
B-3
B-1B-2B-7
B-3B-6
B-10B-10B-10B–1B-2
B-10B-2B-10
B-1B-2B-1B-2
B-1B-2
Item No.
131344
811333198822624
1031911647
13392
111166564
1212
Stock Number1005-716-09991005-716-1812
1005-716-19101005-716-19111005-716-19131005-716-19221005-716-19231005–716-19261005-716-1935
1005-716-27741005-722-89071005-726-56281005-726-56321005-726-58791005-726–59701005-731-29101005-986–0261
4933–726-61755310-261-71615310–716-19055310-726-56345315-013-71555315-534–99215315-534-99355315-534-99385315-534-99445315-534-9948
5315-535–1190
5315-716-19065320-011-8047
5320-682-18625340-535-1209
Item No.
B-1B-2B-7B-7B-7B-7B-1
B-7
B-10B-10B-9B-10B-9B-7B-1B-2B-10B-7B-7B-9
B-7B-8B-1B-2B-7
B-5B-7
B-7
Figure No.10228
1211678
1011225361
15337
1413215416119951
117799
10
Reference No. Mfg Code Fig. No. Item No. Reference No. Mfg Code Fig. No. Item No.
MS16535-114 96906 9 5349921 19204 B-5 5101836 81580 B-7 14 5349925 19204 3118047 19204 1 5349927 19205 B-7 3
11 3B-7 7 5349931 19205 1B-8 7 5349932 19204 9
137155 00000 B-5 1 5349935 19204 B-3 45019316 19204 B-10 8 5349938 19204 15196456 19204 B-10 11 5349942 19204 B-1 85196480 19204 B-10 10 B-2 85-96481 19204 B-10 12 5349943 19204 5
B-8
B - 5
B-8
B-8
B-8B-5
B-5
B-3
B-6B-3B-5
B-3B-8B-5
B-3
B-3
B-8B-6
B-5B-5B-3B-6B-8
B-4
B-8B-5
B-8
B-5
B-4B - 5
46
B-5
B-8B-3B-8
B-6
B-6
TM 9-1005-229-35
53499445349947
5349948
5351190
53511915351194
53511955351196535119853512015351209
53512105557152555973855643645653427
5653429565343156534325653433610882863014486301449630145063014526301453
6301456
63014646301469630147063014726301474
Section IV. INDEX - FEDERAL STOCK NUMBER AND REFERENCE
NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBER —
Continued
1920419205
19204
19204
1920419204
1920419204192041920419204
1920519204192041920419204
19204192041920419204192041920419204192041920419204
19204
1920419204192041920419204
B-8B-7B-8B-7B-8B-1B-2B-5B-7B-8B-3B–6B–5B-8B-7B-8B-5B-10B-10B-10B-1B-2B-3B-10B-2B-5B-10B-6B-3B-6B-5B-1B-2B–1B-2B-3B-8B-3B-6B-5
622119964424789
101031911647
13133962
11116666374
6301481630148265739367160997
7160998
71609997161812
71619057161906716191071619117161913716191871619217161922716192371619267161927716193071619317161935
71627747228907726562876256297265631726563272656337265634726587972659707266175731002473129107791433
19204192041920419204
19204
1920419204
1920419204192041920419204192041920419204192041920419204192041920419204
1920419204192041920419204192041920419204192041920419204192051920419204
B-5B–5B-1B–1B-2B–1B-2B-3B–1B-2B-7B-7B–7B-7B-7B-4B–3B–7B–1B-3B-4B-2B-7B-7B-8B-6B–10B–10B-9B–9B–9B-9B-9B-10B-9B–10B-8B-7B-1B-2
8121412121313102
121358
1211276783
1416101122665342617
121583
47
By Order of the Secretary of the Army:
Official:
W. C. WESTMORELAND,General, United States Army,Chief of Staff.
KENNETH G. WICKHAM,Major General, United States Army,The Adjutant General.
DISTRIBUTION :
To be distributed in accordance with DA Form 12-40, (qty rqr block no. 109) Direct and General Supportmaintenance requirements for Submachine Guns; Caliber .45, M3 and M3A1.
*U.S. GOVERNMENT PRINTING OFFICE: 1990 - 261872/21195
TM 9-1005-229-35
48
PIN 026388-000
This fine document...
Was brought to you by me:
Liberated Manuals -- free army and government manuals
Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap “watermarks” and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends?
I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on.
I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines:
<A HREF=http://www.liberatedmanuals.com/>Free Military and Government Manuals</A>
– SincerelyIgor Chudovhttp://igor.chudov.com/
– Chicago Machinery Movers
