SUMMER OFF-THE-SHELF 2005 · 2015-11-02 · OFF-THE-SHELF 2 SUMMER 2005 VISIT US AT: OFF-THE-SHELF...

Order Online at: www.hittite.com20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Boston • Istanbul • London • Munich • Seoul • Shanghai

NEW RF TO MILLIMETERWAVE IC PRODUCTS FROM HITTITE

SUMMER

2005OFF-THE-SHELF

Medium Power Amps

HMC383 & HMC451

• Covering 5 to 30 GHz • Gain: 16 to 22 dB • Saturated Output Power: +18 to +22 dBm

See Page 2

INSIDE.....

SPDT Switch Module

HMC-C011

• DC - 20 GHz • 50 dB Isolation • Fast Switching: 1 nS

See Page 3

24 GHz VCO w/ ÷16

HMC533LP4

• Output Power: +11 dBm • 100 kHz SSB Phase Noise: -95 dBc/Hz • Single +5V Supply

See Page 5

HITTITE STANDARD PRODUCTS ENABLE

ALL SMT MICROWAVE RADIO DESIGN Microwave and millimeterwave designers have traditionally used die components to satisfy demanding requirements for the transmit (Tx), receive (Rx), LO generation, and LO distribution sections of the radio. In order to reduce overall cost, high frequency designers are turning more often to surface mount (SMT) components and a PCB based approach, in order to leverage in-house automated pick and place and reflow

equipment. Within the past year, Hittite Microwave has released 42 new SMT products for the microwave radio and millimeterwave market, all of which are available in RoHS compliant packaging.

(Continued on page 6)

LOW NOISE PLO MMIC FOR 15 GHZ VSAT APPLICATIONS

Integrates VCO, Phase/Frequency Detector, Prescaler & Loop Amp.Building upon our extensive product line of MMIC VCOs, Hittite announces an InGaP HBT Phase Locked Oscillator (PLO) MMIC for VSAT subscriber equipment. The HMC535LP4 PLO MMIC provides a single ended RF output in the range of 14.6 to 15.4 GHz, while delivering high output power of +11 dBm, and extremely low single sideband phase noise of -110 dBc/Hz at 100 kHz offset. Output power and phase noise performance are excellent over temperature and shock due to the monolithic construction.

The PLO MMIC accepts a single-ended, or a differential reference oscillator input signal in the range of 228 to 240 MHz, with a power level between 0 and +10 dBm. The reference signal source may be fixed or swept.

Product Showcase

* 21 NEW PRODUCTS RELEASED!

BROADBAND HIGH DYNAMIC RANGE

LNA FOR WIRED & WIRELESS APPLICATIONS

GaAs pHEMT MMIC Combines Low Noise Figure & High IP3 from 0.3 to 3.0 GHzA new high linearity SMT LNA meets the needs of RF design engineers. The HMC374 LNA is well suited for applications within cellular /3G infrastructure, repeaters, WiMAX, broadband wireless access, and ISM frequency bands between 300 and 3000 MHz. Compared to discrete solutions, the HMC374 GaAs pHEMT MMIC LNA offers higher reliability, smaller PCB footprint and lower component count.

The HMC374 exhibits a low 1.8 dB Noise Figure, with +36 dBm output IP3, and 15 dB small signal gain. This self biased LNA is unconditionally stable & provides very consistent performance over temperature. The high output IP3 is particularly well suited in applications where the output of the LNA is fed directly into a high IP3 mixer, or applications where the LNA is succeeded by a high loss device such as a power splitter, or an attenuator.

The HMC374 is housed in a SOT26 package, and is offered in both standard (HMC374) and RoHS compliant (HMC374E) versions. Evaluation samples and production quantities are available from stock.

(Continued on page 6)

Figure 1. HMC535LP4 PLO

OFF

-TH

E-S

HE

LF

SUMMER 2005 VISIT US AT: www.hittite.com2

OF

F-T

HE

-SH

ELF

3 VISIT US AT: www.hittite.com SUMMER 2005

BROADBAND GAIN BLOCKS, DRIVERS & POWER AMPS

HMC474MP86 +5V SiGe Gain Block, DC - 6 GHz

Features

Gain: 15.5 dB

P1dB Output Power: +8 dBm

Output IP3: +22 dBm

Cascadable 50 Ohm I/Os

Single Supply: +3V to +10V

Available RoHS Compliant

Low Cost Gain Stage!The HMC474MP86 is a general purpose SiGe HBT Gain Block MMIC SMT Amplifier covering DC to 6 GHz. This Micro-P packaged amplifier can be used as a cascadable 50 Ohm RF/IF gain stage with up to +10 dBm output power. The HMC474MP86 offers 15.5 dB of gain with a +22 dBm output IP3 at 850 MHz while requiring only 25 mA from a single positive supply. The HMC474MP86 is an ideal buffer amplifier for Cellular / 3G, Broadband Cable, Fixed Wireless & IF applications.

HMC383 & HMC451 Medium Power Amplifiers Cover 5 to 30 GHz

Gain & Noise Figure

Features

Gain: 16 to 22 dB

Saturated Output Power: +18 to +22 dBm

Output IP3: +25 to +30 dBm

Single +5V Supply

50 Ohm Matched I/Os

Compact Size, Flat Output Power!The HMC383 and HMC451 are general purpose GaAs PHEMT MMIC Driver Amplifiers operating between 12 to 30 GHz & 5 to 20 GHz. These amplifiers provide 16 to 22 dB of gain and +18 to +22 dBm of saturated power from +5V supply voltages. Consistent gain and output power across each operating band make it possible to use a common driver/LO amplifier approach in multiple radio bands. Both the HMC383 and HMC451 amplifiers can easily be integrated into Multi-Chip-Modules (MCMs) due to their small size.

HMC383LC4 SMT Medium Power Amplifier, 12 - 30 GHz

Features

Gain: 15 dB

Saturated Output Power: +18 dBm

Single +5V Supply

50 Ohm Matched I/Os

RoHS Compliant 4 x 4 mm Package

Multi-Purpose; Easy to Use!The HMC383LC4 is a general purpose GaAs PHEMT MMIC Driver Amplifier housed in a leadless RoHS compliant SMT package. The amplifier provides 15 dB of gain and +18 dBm of saturated power from a +5.0 V supply voltage. Consistent gain and output power across the operating band make it possible to use a common driver/LO amplifier approach in multiple radio bands. The RF I/Os are DC blocked and matched to 50 Ohms for ease of use. The HMC383LC4 elimates the need for wire bonding, allowing use of surface mount manufacturing techniques.

�

�

�

�

�

��

��

��

��

��

��

� � � � � � �

��

��

�

��

Broadband Gain

�

��

��

��

��

� ��

��

��

��

�

��

Broadband Gain & Return Loss

��

��

��

��

�

�

��

��

��

� ��

��

��

�

��

OFF

-TH

E-S

HE

LF


OF

F-T

HE

-SH

ELF


BROADBAND, HIGH PERFORMANCE CONTROL DEVICES

HMC547LP3 Broadband High Isolation SPDT SMT Switch, DC - 20 GHz

Features

High Isolation: 50 dB @ 5 GHz 38 dB @ 20 GHz

Low Insertion Loss: 1.5 dB @ 5 GHz 2.0 dB @ 20 GHz

3 x 3 mm QFN SMT Package


Ideal for Test Equipment!The HMC547LP3 is a broadband high isolation non-reflective GaAs MESFET SPDT switch in a leadless 3 x 3 mm QFN SMT plastic package. Covering DC to 20 GHz, the switch offers high isolation of 50 dB @ 5 GHz and 38 dB @ 20 GHz, with +48 dBm IP3 and very fast switching speed of 6 nS. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply.

HMC346LC3B Wideband Analog SMT VVA, DC - 18 GHz

Features

30 dB Attenuation Range

Absorptive

Low Phase Shift vs. Attenuation

Simplified Voltage Control

RoHS Compliant 3 x 3 mm SMT Package

Stable Insertion Phase!The HMC346LC3B is an absorptive Voltage Variable Attenuator (VVA) in a leadless RoHS compliant 3 x 3 mm SMT package operating from DC - 18 GHz. It features an on-chip reference attenuator for use with an external op-amp to provide simple single voltage attenuation control, 0 to -3V. The device is ideal in designs where an analog DC control signal must control RF signal levels over a 30 dB amplitude range.

HMC-C011 High Isolation SPDT Switch Module, DC - 20 GHz

Features

Isolation: 50 dB

Insertion Loss: 2 dB

Fast Switching: 1 nS

CMOS Control

Low Video Transients: 20 mV pk-pk

Field Replacable SMA Connectors

Ideal for Test Equipment!The HMC-C011 is a high performance non-reflective SPDT switch in an hermetic connectorized housing with field replaceable SMA connectors. Covering DC to 20 GHz, the switch offers 2 dB of insertion loss, 35 to 65 dB isolation and +23 dBm of input P1dB. The switch includes a high speed CMOS driver providing extremely fast 1 nanosecond rise and fall times, low video transients and requires a single positive +5V bias.

Insertion Loss & Isolation

��

��

��

��

��

��

�

��

��

��

��

��

��

��

� � ��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

Insertion Loss & Isolation

��

��

��

��

��

��

��

�

��

��

��

��

��

��

��

�

� � ��

��

��

��

��

��

��

��

��

��

��

��

��

Relative Attenuation

��

��

��

��

��

��

��

��

�

� � � � � ��

��

��

��

��

��

��

�

��

OFF

-TH

E-S

HE

LF


OF

F-T

HE

-SH

ELF


INNOVATIVE, HIGH LINEARITY BROADBAND MIXERS

HMC214MS8 High IP3 SMT Mixer, 2.4 - 4.0 GHz

Features

Input IP3: +34 dBm

LO to RF Isolation: 28 dB

Input P1dB: +22 dBm

No External Components

Ultra Small MSOP8


Ideal for WiMAX & Fixed Wireless!The HMC214MS8 is a high dynamic range passive MMIC mixer in an 8 lead plastic SMT package covering 2.4 to 4 GHz. Excellent input IP3 performance of +34 dBm for down-conversion and +31 dBm for up-conversion is provided for WiMAX and other 3.5 GHz Fixed Wireless applications at an LO drive of +17 dBm. With a 1 dB compression of +22 dBm, the RF port will accept a wide range of input signal levels. LO to RF & LO to IF isolations are maintained at 25 to 30 dB.

HMC129LC4 High Isolation Double-Balanced Passive Mixer, 4 - 8 GHz

Features

Conversion Loss: 7 dB

LO to RF & IF Isolation: 40 dB

Input IP3: +17 dBm

+9 to +15 dBm LO Range

RoHS Compliant 4x4 mm SMT Package

Low Conversion Loss!The HMC129LC4 is a double-balanced MMIC mixer housed in a leadless RoHS compliant SMT package which can be used as an upconverter or downconverter in the 4 to 8 GHz band. The HMC129LC4 is ideally suited for applications where small size, no DC bias, and consistent IC performance are required. This mixer can operate over a wide LO drive input of +9 to +15 dBm and wide IF bandwidth of DC - 3 GHz. It performs equally well as a Bi-Phase modulator or demodulator.

HMC260 / 292 / 329LC3B Double-Balanced Mixers Covering 14 to 32 GHz

Features

Input IP3 to +20 dBm

LO/RF Isolation to 40 dB

Wide IF Bandwidth: DC - 8 GHz

Passive: No DC Bias Required

RoHS Compliant 3 x 3 mm SMT Package

No External Matching!The HMC260/292/329LC3B are passive double balanced mixers in leadless RoHS compliant SMT packages that can be used as upconverters or downconverters over 14 to 32 GHz. These mixers require no external components or matching circuitry. They provide excellent LO to RF and LO to IF suppression eliminating LO filtering. The mixers operate with LO drive levels from +9 to +15 dBm and are ideal for Microwave Radio, VSAT, Military & Test Equipment applications.

Conversion Gain vs. Temperature

Input IP3 vs. Temperature

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

��

�

� � � � � � �

��

��

�

��

Typical Performance

RF/LOFreq. (GHz)

14 - 26 20 - 30 24 - 32

IF Freq. (GHz) DC - 8 DC - 8 DC - 8

Conv. Gain (dB) -7.5 -8 -10

LO/RF Isol. (dB) 39 38 40

IIP3 (dBm) 20 19 19

HMC26

0LC3B

HMC29

2LC3B

HMC32

9LC3B

OFF

-TH

E-S

HE

LF


OF

F-T

HE

-SH

ELF


NEW PHASE SHIFTER & VCO PRODUCTS!

Features

Pout: +7 to +12 dBm

Phase Noise: -95 to -110dBc/Hz @100 KHz

No External Components

QFN Leadless SMT Packages


Applications

VSAT Radio

Pt to Pt/Multi-pt Radios

Test Equipment & Industrial Controls

Military End-Use

HMC247 / 538LP4 / C010 Analog Phase Shifters Covering 6 to 21 GHz

Features

Wide Bandwidth

Continuously Variable

Stable Insertion Loss vs. Phase Shift

Alternative Packaging Options

Applications

Optical Communications

Instrumentation

Laboratory Test Sets

Test Equipment

Military & Space

New Product Line for Test Equipment, Telecom & Military / Space!

The HMC247 is a 9 to 21 GHz Analog Phase Shifter die. Phase shift is controlled via an analog DC voltage control from 0 to +10V, providing continuously variable insertion phase of 0 to 300 degrees at 9 GHz. Insertion loss is 5 dB, and is very consistent versus phase shift. The HMC247 is offered in bare die form and is compatible with standard wirebonding and epoxy and eutectic die attach techniques.

For SMT applications, the HMC538LP4 6 - 16 GHz Analog Phase Shifter is housed in a leadless surface mount QFN 4 x 4 mm package. This variable phase shifter accepts an analog control voltage from 0 to +5V, and provides continuously variable insertion phase from 0 to 800 degrees at 6 GHz, and 0 to 450 degrees at 16 GHz.

For test equipment and instrumentation applications, the HMC-C010 offers the same outstanding performance as the HMC538LP4, and is housed in a flanged module with field replacable SMA connectors.

These phase shifters are particularly useful for adjusting the phase of clocks in fiber optic systems and test equipment.

MMIC VCOs for Microwave, Military and Sensor Applications!

The HMC513LP5, HMC514LP5, HMC533LP4 are fully integrated GaAs InGaP HBT VCOs. These MMIC VCOs incorporate an integrated resonator, negative resistance device, and varactor diode, resulting in excellent phase noise performance over temperature, shock, and process due to the monolithic structure. These VCOs deliver high output power, operate from a single positive supply voltage, and allow the prescaler function to be disabled in order to reduce power consumption.

The HMC533LP4 is a 23.8 - 24.8 GHz MMIC VCO featuring +12 dBm output power, and a divide-by-16 output. The HMC533LP4 is housed in a leadless QFN 4 x 4 mm surface mount package, operates from a +5V supply, and exhibits -95 dBc/Hz SSB Phase Noise at 100 kHz offset.

The HMC513LP5 10.43 - 11.46 GHz MMIC HBT VCO, and the HMC514LP5 11.17 - 12.02 GHz MMIC HBT VCO feature +7 dBm power output, as well as Fo/2 and divide-by-4 divided outputs. Both VCOs are housed in leadless QFN 5 x 5 mm surface mount packages, operate from a single +3V supply, and exhibits -110 dBc/Hz SSB Phase Noise at 100 kHz offset.

HMC513LP5 / 514LP5 / 533LP4 MMIC VCOs Covering Up to 24.8 GHz

Typical Performance

PartNumber

Frequency(GHz)

FunctionInsertionLoss (dB)

PhaseRange (Deg)

2nd HarmonicPin= 0 dBm (dBc)

Control Voltage

Range (Vdc)

HMC538LP4 6 - 16 Analog 8800˚ @ 6 GHz450˚ @ 16 GHz

10 0V to +5V

HMC-C010 6 - 16 Analog 8800˚ @ 6 GHz450˚ @ 16 GHz

10 0V to +5V

HMC247 9 - 21 Analog 5300˚ @ 9 GHz60˚ @ 21 GHz

50 0V to +10V

Typical Performance

PartNumber

Frequency(GHz)

FunctionOutputPower(dBm)

10kHz SSB Phase Noise

(dBc/Hz)

100kHz SSBPhase Noise

(dBc/Hz)

BiasSupply

HMC513LP510.43 - 11.46 /

5.21 - 5.73VCO w/ Fo/2 & ÷4 7 -85 -110 +3V @ 275mA

HMC514LP511.17 - 12.02 /

5.58 - 6.0VCO w/ Fo/2 & ÷4 7 -85 -110 +3V @ 275mA

HMC533LP4 23.8 - 24.8 VCO w/ ÷16 12 -70 -95 +5V @ 220mA

OFF

-TH

E-S

HE

LF


OF

F-T

HE

-SH

ELF


The 23 GHz Microwave Radio block diagram below shows how Hittite SMT components can reduce parts count, shorten design cycles and simplify manufacturing.

Hittite low noise VCOs are widely used to generate the fundamental LO signals for various radio designs. The HMC386LP4 VCO w/ Buffer Amp, the HMC439QS16G Phase/Frequency Detector, and the HMC365S8G Divide-by-4 Prescaler can be combined to quickly construct a 2.6 - 2.8 GHz LO signal with +5 dBm output power and very low phase noise.

Microwave radios frequently employ discrete multiplier chains in the LO distribution section which can be problematic to manufacture with consistency, in addition to the spurious issues that they can create. The HMC443LP4 X4 Active Multiplier can be used to generate a 10.4 to 11.2 GHz LO signal, with +4 dBm output power and better than 25 dBc sub-harmonic suppression.

In the transmit section of the radio, the HMC342LC4 LNA/Driver, and the HMC499LC4 Medium Power Amplifier can be used in cascade to create a driver amplifier or output stage.

The combination of these two GaAs pHEMT amplifiers will produce, +24 dBm output power and 37 dB Gain, while operating from a single +5V supply.

Hittite I/Q and IRM mixers are ideal for receive chain application which require high IP3 and high image rejection. The new HMC523LC4 offers wide IF bandwidth, high input IP3 and excellent RF to LO Isolation. Compared with a hybrid based implementation, this I/Q MMIC mixer offers significantly reduced PCB area, consistent performance, and excellent amplitude and phase balance as a result of its monolithic construction. When configured as an Image Reject Mixer using an external IF hybrid, the HMC523LC4 provides 25 dB of image rejection at midband. Such high levels of image rejection would be difficult if not impossible to achieve on a production basis using mixers, splitters and couplers in a hybrid MIC or PCB based approach, while this mixer acheives such high levels inherently.

All microwave product data sheets are available at www.hittite.com.

APPLICATION SOLUTIONS!

ALL SMT MICROWAVE RADIO DESIGN... (continued from page 1)

LOW NOISE PLO MMIC... (continued from page 1)

The fully integrated HMC535LP4 incorporates a VCO, phase frequency-detector (PFD), fixed modulus prescaler, and loop amplifier. The reference oscillator input and a sample of the divided VCO output are fed to the phase frequency detector and the loop amplifier. In closed loop mode, the integrated phase frequency detector tunes the VCO until phase lock

is achieved. A digital Lock Detect (LD) output is provided to confirm the status of the loop. Compared to discrete PLO approaches, the HMC535LP4 will significantly reduces the component count, and the board space required to produce a low phase noise Local Oscillator signal as required by high symbol rate digital radios.

The HMC535LP4 requires +5V and +12V supply voltages, consumes less than 2W of power and is housed in a 4 x 4 mm SMT leadless QFN package. Both standard (HMC535LP4) and RoHS compliant (HMC535LP4E) versions are available. Sample and production quantities are available from stock and may be ordered on-line.

Custom PLO products can be designed for customers’ application specific requirements. Contact [email protected].

��

��

� ��

��

� ��

��

��

��

��

Figure 2. HMC535LP4 PLO Functional Diagram

� �

� �

� �

��

� ��

��

��

��

HMC517LC4Low Noise Amp• 17 - 26 GHz• 19 dB Gain• 2.5 dB NF

HMC264LC3BSub-Harmonic Mixer

• 21 - 31 GHz RF• 10.5 - 15.5 GHz LO

HMC213MS8DBL-BAL Mixer

• 1.5 - 4.5 GHz RF• DC - 1.5 GHz IF

• Hi-Isolation

HMC342LC4LNA / Driver• 13 - 25 GHz• 22 dB Gain• +10 dBm Pout

HMC499LC4Med. Power Amp• 21 - 32 GHz• +24 dBm P1dB• 15 dB Gain

HMC311ST89SiGe Gain Block

• DC - 6 GHz• 15 dB Gain

• +15 dBm P1dB

HMC365S8GDivide-By-4

• DC - 13 GHz Input• Low Phase Noise

• ÷2, ÷3, ÷5, ÷8 Available

HMC386LP4VCO w/ Buffer Amp

• 2.6 - 2.8 GHz Fo• Low Phase Noise

-115 dBc/Hz @ 100 kHz

HMC443LP4x4 Active Multiplier• 9.8 - 11.2 GHz Fo

• +3 dBm Pout• Very Low Phase Noise

HMC441LC3BMedium PA• 6 - 18 GHz

• 17 dB Gain• +20 dBm P1dB

HMC442LC3BMedium PA

• 17.5 - 25.5 GHz• 13 dB Gain

• +21 dBm P1dB

HMC523LC4I/Q Mixer / IRM

• 15 - 23.6 GHz RF/LO• 25 dB Image Rejection

• +25 dBm Input IP3• DC - 8 GHz IF

HMC331LC3BPassive Freq. Doubler

• 12 - 18 GHz Fin

• 50 dB 1, 3, 4 Fo Isolation

HMC478MP86SiGe Gain Block

• DC - 4 GHz• 22 dB Gain

• +18 dBm P1dB

HMC439QS16GPhase-Freq. Detector

• 10 - 1300 MHz• Low Phase Noise,

-153 dBc/Hz@ 100 kHz

Typical All SMT Microwave Radio Block Diagram

NEW!

OFF

-TH

E-S

HE

LF


OF

F-T

HE

-SH

ELF


FOR MORE INFORMATION...Hittite Microwave CorporationUSA Corporate Headquarters Phone: 978-250-3343 Fax: 978-250-3373 [email protected]

Hittite Microwave CorporationEastern N. American Sales Office Phone: (610) 998-1470 Fax: (610) 998-1473 [email protected]

Hittite MikrodalgaSanayi ve Ticaret Ltd. Sti [email protected]

Hittite Microwave Europe Limited Phone: +44 1256-817000 Fax: +44 1256-817111 [email protected]

Hittite Microwave Deutschland GmbH Phone: +49 8031-97654 Fax: +49 8031-98883 [email protected]

Hittite Microwave Asia Co., Limited Phone: (82-2) 559-0638 Fax: (82-2) 559-0639 [email protected]

Hittite Microwave Co., LimitedShangHai Office Phone: (86-21) 62376717 Fax: (86-21) 62376716 [email protected]

Beijing Office Phone: (86-10) 87756717 Fax: (86-10) 87756899 [email protected]

Shenzhen Office Phone: (86) 755-8350-5422 Fax: (86) 755-8350-5258 [email protected]

NORTH AMERICACANADA; Ottawa & Montreal: Repwave-Scientech +613-270-9811

Toronto: Repwave-Scientech +905-465-1584

USA North East & Mid-Atlantic;

CT, MA, ME, NH, RI & VT: dBm Technical Sales 978-256-7100

So. CT, Metro NY/LI & No. NJ: Comp Tech 201-288-7400

E. PA, So. NJ & Upstate NY: Brooks Associates 732-873-1900

DC, DE, MD, VA & WV: Vincent Pirro Electronics 410-489-9554

USA Mid-West;

IA, MN & E. OH: DyTec, Inc. 800-872-5746

IN, KS, KY, MI, MO, NE W. OH, So. IL & WI: HMC East 610-998-1470

No. IL: TK Technologies Inc. 847-991-7160

USA South East;

FL: Spartech South 321-727-8045

GA, NC, SC, TN, AL & MS: HMC East 610-998-1470

USA South West;

TX, OK, LA & AR: N & W Sales, Inc. 817-461-4443

AZ & NM: Saguaro Technical Sales, Inc. 480-947-3724

USA West;

No. CA & NV: Custom & Wireless Sales 408-371-0222

So. CA: Acetec 858-784-0900

OR & WA: Sea-Port Technical Sales 425-702-8300

CO & UT: W. Howard Associates, Inc. 303-766-5755

EUROPE, MID-EAST & AFRICABenelux: Datron BV +31-35-6246649

Czech Republic,Poland & Slovak Republic: Hittite Microwave Europe Limited +44 1256-817000

Finland: Hittite Microwave Europe Limited +44 1256-817000

France: Salies SA +33-1-69-02-2570

Germany, Austria, & Switzerland: Hittite Microwave Deutschland GmbH +49 8031-97654

Germany, Austria, Denmark & Switzerland: MRC Components OHG +49 8161-9848-0

Israel: Starlight Technologies, Inc. +972-3-9410555

Italy: Special-Ind SPA +39-02-6074741

Norway: Bredengen AS +47-2100-9100

Spain & Portugal: Altaix Electronica S.A.L +34-91-636-39-39Sweden: Amtele AB +46-8-556-466-00

South Africa: RF Design Laboratory CC +27-21-762-5365

United Kingdom & Ireland: Link Microtek Ltd +44 1256-355-771

ASIA & SOUTH PACIFICAustralia: ASD Technology Pty Ltd +61-2-9884-7486

China & Hong Kong: Secom Telecom Co., LTD. +86-755-25155888

Wai Tat Electronics Ltd. +852-2799-7393

India: Syratron +91-80-5591107/5531031

Indonesia, Malaysia,Philippines & Singapore MEDs Technologies, Pte., Ltd. +65-6453-8313

Japan: Saint Technology +81-3-5330-6411

Seki Technotron Corp. +81-33820-1711 +81-6-6386-1232

Korea: ENS Engineering +82-2-562-9819

New Zealand: ASD Technology Pty Ltd +61-2-9884-7486

Taiwan R.O.C.: Bandtek International Co., Ltd. +886-2-2657-2615

NORTH AMERICA DISTRIBUTION:Future Electronics800-Future-1Ext. 2754, Americaswww.FutureElectronics.com/rf

NEWS FROM HITTITE!

HITTITE ADDS NEW

MANUFACTURERS REPRESENTATIVES

Comp-Tech Sales to Cover Metro NY/NJComp-Tech Sales, headquartered in New Jersey represents a broad line of electronic components with an emphasis on RF/Microwave devices. Their office in Hasbrouck Heights, NJ offers full support to customers in Metro New York, Long Island, Northern New Jersey & Connecticut (Fairfield county). Comp-Tech Sales can be contacted via telephone at 201-288-7400, via fax at 201-288-7583 or email at [email protected]. Visit their website at www.comp-techsales.com.

Brooks Associates to Cover So. NJ, PA & No. NYBrooks Associates specializes in RF/Microwave sales to the military, space and consumer electronics industries. Their offices in New Jersey and Pennsylvania offer full support to customers in the Southern New Jersey, upstate New York and eastern Pennsylvania. Brooks can be contacted via telephone at 732-873-1900, via fax at (732)-873-9009 or email at [email protected].

Sea-Port Technical Sales to Cover WA & ORSea-Port Technical Sales established in 1989, offers a suite of high end RF, Microwave, and Fiber Optic products. Headquartered in Bellevue, Washington, Sea-Port offers full support to Oregon and Washington state. Sea-Port can be contacted via telephone at 425-702-8300, via fax at 425-702-8388 or email at [email protected]. Visit their website at www.seaporttech.com.

NEW SUMMER 2005SELECTION GUIDE RELEASED!HMC is pleased to announce the availability of the Sum-mer 2005 Product Selection Guide which summarizes over 340 products. The se-lection guide features include organization by product line as well as by market applica-tions including: Automotive, Broadband, Cellular/PCS/3G, Fiber Optic, Microwave & mmWave Communica-tions, Test & Measurement, Military and Space.

This new Selection Guide contains over 52 products not found in the Autumn 2004 Selection Guide and 22 prod-ucts not found in the 2005 Designer’s Guide Catalog.

Request your copy of the new Summer 2005 Selection Guide at www.hittite.com by selecting the “SUBMIT IN-QUIRY” left hand navigation button. New product data sheets can be found on-line.

© 2005, Hittite Microwave Corporation, All Rights Reserved.20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Boston • Istanbul • London • Munich • Seoul • Shanghai

SUMMER

2005

What We Do

Hittite Microwave Corporation is an innovative designer and manufacturer of analog and mixed-signal ICs, MIC modules and sub-assemblies for RF, microwave and millimeter-wave applications covering DC to 110 GHz. Our RFIC/MMIC products are developed using state-of-the-art GaAs, InGaP/GaAs, InP, SOI and SiGe semiconductor processes utilizing MESFET, pHEMT, mHEMT and HBT devices. Our products include;

Power Amplifiers Attenuators Mixers VCOs Gain Blocks Phase Shifters Converters Dividers/Detectors Driver Amplifiers Switches IRMs Multipliers LNAs Transceivers Modulators PLOs / PLLs

We also design and supply highly integrated custom ICs, MCMs and sub-systems that combine multiple functions for specific requirements. We select the most appropriate semiconductor and package technologies, uniquely balancing digital and RF integration techniques, to produce a product that is easy and cost effective for our customers to use.

Our custom and standard products support a wide range of wireless / wired communica-tions and radar applications including those listed below:

Automotive Telematics & Sensors

Broadband CATV, DBS, WiMAX, WLAN, Fixed Wireless & UWB

Cellular / PCS / 3G Handset / Handheld, PLMR & Infrastructure

Fiber Optic OC-48 to OC-192

Microwave / mmWave Communications Pt to Pt / Multi-Pt Radios & VSAT

Test & Measurement Commercial / Industrial Sensors & Test Equipment

Military C3I, ECM & EW

Space Payload Electronics

Every component is backed by Hittite Microwave’s commitment to total quality. HMC is ISO 9001:2000 certified, and every Hittite employee and subcontractor is responsible for maintaining the highest level of quality. We are constantly working towards im-provement of our procedures and processes, thus providing our customers with products that meet or exceed all requirements, are delivered on-time and function reliably throughout their useful life.

Date post:	09-Jul-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

SUMMER OFF-THE-SHELF 2005 · 2015-11-02 · OFF-THE-SHELF 2 SUMMER 2005 VISIT US AT: OFF-THE-SHELF...

Documents