SupaRule Cable height meters
Presented by: Gary Carroll DirectorFeb 2004
Using the SupaRule Cable Height Meter
• Ultrasonic handheld meter for measurement of • Cable height• Cable sag• Overhead clearance to ground.
• Safest method for cable height measurement.• By eliminating cable contact and the use of heavy fiberglass
poles
Cable Height Meter
Key advantages:
• Safety: • No contact with conductors
• One simple solution: • One button-one man
operation
• Easy to use.
• Efficient use of resources.
Cable Height Meter
Cable Height Meter
Competition
• Telescopic rods:• Cumbersome, heavy to
carry, break easy.• Accuracy depends heavily
on experience of user.• Frequent calibration
required.
• Laser• Difficult to target
conductors.• Accurate units cost €3,000-
€5,000
Cable Height Meter
Theory of operation
• Sends (ultra) sound wave to target
• Measures time to echo
• Calculates distance based on speed of sound
• Adjusts for air temperature
1. Select: M(metric) or I (imperial) at the back of unit.
2. Set the CAL mode switch to the WIRE position.
3. Press the ON key to power on
4. Stand directly underneath the conductors(s) to be measured.
5. Press the MEASURE Key to take measurement
6. Press the READ key to display each of the stored wire height differences (Stored Measurements).
CHM Operation
Newer CHMs: Same Functions/Different Implementation
• Older CHM had a Clear (C) button, On newer models, to clear screen press Read (W: wire) and Measure (+) buttons together.
• Older CHM had a battery check button. Newer models have a low battery signal appearing on screen, if battery is low.
• Older units used (M) measurement to select differences between wires; newer models use READ button.
Taking a reading:
• Press Measure (+). Unit automatically captures all wires within the ultrasonic cone.
• Read measurement by scrolling down the Read (W for wire) button, from 1 (lowest wire) to 2 (spacing in between cable 1 and 2), 3 and up to 6 wires, provided conductors are stacked above each other.
• If taking reading of wires parallel to each other, a number of separate measurement need to be taken.
CHM Operation
Specification• Accuracy: 0.5% ± 2 digits• Minimum gap between wires:150 mm• Operating Temp. Range:-10 °C to 40 °C• Battery Life (9V Alkaline type): 50,000 measurements• Auto power off delay: 3 minutes• Serial number location: underneath
battery.
Models available:• 3 wires: CHM 300• 6 wires: CHM 600• 3 to 15 m (=10 to 50ft)
Standard units:CHM 300/600
• 3 to 23 m (= 10 to 75ft)
Model “E”: CHM 300/600E
Cable Height Meter
Cable Height Meter
• This indicates a “poor target”, and normally happens when the cables are moving due to wind, etc.
Screen is blank• Check battery is inserted correctly. • Open battery door on the bottom rear of the unit. • The battery is inserted with the terminals
inwards. • The + and - symbols on the battery should
correspond with the + and - symbols on the inside of the battery compartment.Unit does not
measure all wires
• Ensure that horizontal distances between wires are within the sonic beam.
If the display shows - - -.- - -
Incorrect readings• Ensure CAL mode switch is on correct position,
i.e. WIRE for cable height measurement, and WALL for horizontal distance measurement.
• Ensure no walls or similar obstructions within 2 meters either side of unit, as reflections from these can interfere with correct operation.
Cable Height Meter
Do:
• Position the unit on the ground, directly underneath the conductor to be measured.
• Align the unit in the direction of the conductor, with the cone , pointing towards the conductor.
• Keep the unit dry; if wet, leave upside down in a warm area
Don’t:
• Avoid clutter around conductorto be measured
• Avoid water, rain, snow, humidity.
• Avoid sudden changes of temperature.
Cable Height Meter
Warranty: • 12 months from purchase date.
Calibration:• The CAL mode switch allows
the user to periodically check the unit, to ensure it is still operating within specification.
Repair:• SupaRule offers repair at a
standard rate. • Quick turn around time - less
than 1 week from receipt of unit.
Return rate:• Under warranty - better than
0.5% / year; typically 0.2%
Product Life• 5 -10 years
Date Distance Measured
• SupaRule offers calibration certificate at €163 / unit.
Cable Height Meter
Complementary products:
• Dynamic Target (DT80) with Model CHM 300DT
• Tripod
• Leather case
Cable Height Meter
Distance MeasurementThank YouFeb 2004