Date post: | 28-Apr-2015 |
Category: |
Documents |
Upload: | paulo-costa |
View: | 30 times |
Download: | 1 times |
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
129
Trace-heating remote module for control
MONI-RMC
MoniTrace remote modules for control(RMC) provide multiple relay outputs forswitching heating cable circuits controlledby the MoniTrace 200N trace-heatingcontrol and monitoring unit. RMC unitsare modular and may be configured with 2 to 32 relay outputs. A single MoniTrace200N unit communicates with up to 10RMC via a single, twisted pair RS-485cable to provide distributed control of upto 128 heating cable circuits.
Control and monitoringThe MoniTrace 200N controls and moni-tors multiple trace-heating circuits basedon pipe or ambient temperatures. Thesetemperatures are collected locally byMoniTrace remote monitoring modules(RMM) connected on the same RS-485network. Based on temperature inputs
from RMM, the MoniTrace 200N deter-mines which heating cable circuits are tobe energised and sends this informationto RMC, which then turn on or off theheating cable power contactors. Becausetemperature inputs and control outputsare located near equipment to be sensedor controlled, wiring costs are reducedsignificantly.
Alarm inputsEach RMC unit includes two inputs tomonitor the status of circuit breakers orpower contactors. For example, one inputmay be used for a common circuit break-er trip alarm, providing an alarm indica-tion at the MoniTrace 200N panel if anycircuits fail due to earth fault or overcur-rent events. Alarms may be reported remotely through an alarm relay
in the MoniTrace 200N or through an RS-485 connection to a host computersupporting the Modbus protocol. Up to 16MONI-RMC-2DI 2 channel digital inputmoduls can be added if required.
ConfigurationsThe MoniTrace RMC are modular, elec-tronic devices that mount on a DIN 35rail. RMC units must be installed in pan-els or enclosures suitable for the areaclassification and environment. For eachRMC installation, purchase one MONI-RMC-BASE kit, which includes the net-work processor, digital inputs, and endterminator; one MONI-RMC-PS24 24-Vdcpower supply; and up to 16 MONI-RMC-2RO 2-channel relay output modules, asrequired.
ON
TxD
I/O RUN
I/O ERR
RxD
CRC
750-312
Address x 1
x 10 +
–
2
MONI-RMC-BASE unit with fourMONI-RMC-2RO modules removed
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
130
Dimensions (in mm)
Overall width = 125 mm + 12 mm per relay module (+ 90 mm for optional power supply)
General
Area of use Ordinary areas
Ambient operating temperature range 0°C to 55°C
Ambient storage temperature range –40°C to 70°C
Relative humidity Max. 95%, noncondensing
Protection IP2X per IEC 529
Supply voltage 24 Vdc
Supply current < 2 A
Relay outputs
Quantity per RMC 1 to 16 two-channel modules (2 to 32 relay outputs)
Total relay outputs via RMCs 128
Type Mechanical, normally open, non-floating
Voltage, maximum 250 Vac, 30 Vdc
Current, maximum AC/DC 2 A
Maximum power 60W/500VA (resistive)
Isolation 4 kV
Life (operations) 1 x 106 at 0.35 A to 0.2 x 106 at 2 A
Connection terminals 0.08 mm2–2.5 mm2 (cage clamp)
Supply module
Voltage 230 VAC/DC
Current 10A
Connection terminals Cage clamp type for cables from 0.08 mm2 to 2.5 mm2
Digital inputs
Quantity per RMC Up to 16 two-channel modules (2 to 32 digital inputs)
Type Solid-state, 24 Vdc source
Current consumption 5mA
Isolation 500 V
Connection terminals 0.08 mm2–2.5 mm2 (cage clamp)
MONI-RMC
0 123
45678
9
0 123
45678
9
ON
TxD
IO/RN
IO/ER
RxD
CRC
Address x 1
x 10
750-
312
Networkprocessor
Supplymodule
Relaymodule
Endtermination
100
38
35
12 12
Digitalinputs
75
D1 D2
D1 D2
24V 0V
24V
0V
L L
N N
L L
N N
L
N
V IN
MONI-RMC-PS24power supply (optionel)
90
750-400 750-612 750-512 750-600
RS-485 networkconnection module
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
131
Connection details
MONI-RMC
Communication to MONI-200N-E
Type RS-485
Connection terminals 0.08 mm2–2.5 mm2 (cage clamp)
Cable 1 shielded twisted pair
Length 1200 m max.
Quantity Up to 10 RMC may be connected to one 200N
Address Switch-selectable on RMC, 10 addresses, 50–59
Mounting method Clips to DIN 35 rail
Electromagnetic compatibility
Immunity Complies with EN 50 082-2 (heavy industrial)
Emissions Complies with EN 50 081-2 (heavy industrial)
Ordering details & Weight Part description PN Weight
MoniTrace remote module for control (RMC)
Base unit* MONI-RMC-BASE 309735-000 0.5 kg
Two-channel relay output module** MONI-RMC-2RO 920455-000 55 g
Two-channel digital input module*** MONI-RMC-2DI 062367-000 50 g
24-Vdc power supply MONI-RMC-PS24 972049-000 0.7 kg
* Purchase one base for each RMC installation. Includes network processor, two digital inputs, end termination, and RS-485 connection module with ribbon cable.** Purchase one module for each set of two relay outputs required. Minimum of one module (2 relay outputs), maximum of 16 (32 relay outputs) per RMC base.*** Purchase one module for each set of two digital inputs required. Minimum of one module (2 digital inputs), maximum of 16 (32 digital inputs) per RMC base.
Additional module for each pair of digital inputs required. One MONI-RMC-2DI module is included in each RMC-BASE unit
AC INPUT
OUTPUT, 24Vdc 2 A
0 123
45678
9
0 123
45678
9
ON
TxD
RxD
CRC
Address x 1
x 10 WAG
O75
0-31
2I/0
SYST
EM
750-400 750-612
V IN
750-512
15 16
750-512 750-600
N
L
L N
IO/RN
IO/ER
24V
24V
0V
0V
L
N N
D1 D2
D1 D2
L L
N N
L L
Contactor 2Contactor 1
Contactor coil
Digital input 1
RS-485
24V
0V
Contactor coil supply
24 Vdc
Power supply(typical)
N
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
132
Temperature sensor for ordinary area
MONI-PT100-NH
2 wire Pt100 sensor with glass fiber reinforced polycarbonate junction box for installation in ordinary area.
Area of use Ordinary area
sensor marking NA
Sensor
Type Pt100-Sensor (2 wire)DIN IEC 751, Class B
Material Tip: stainless steelExtension cable: silicone
Temperature measuring range –50°C to +180°C
Temperature range extension cable –50°C to +180°C (+215°C maximum 1000 hrs), max. exposure temp. tip: +400°C
Length 2 m
Diameter Extension cable ca 4.6 mm, tip ca 6.0 mm
Minimum bending radius Extension cable: 5 mm, the measuring tip should not be bended
Enclosure
Ingress protection IP66
Material Glass fiber reinforced polycarbonate (gray)
Dimensions With = 65 mm Height = 65 mm Depth = 57 mm
Cable gland M20 (polyamide) suitable for cable diameters ranging from 10 mm to 14 mm
Operating temperature –30°C to +80°C
Lid sealing gasket material CFC-free Polyurethane
Cover screws Plastic
Mounting For pipe mount use JB-SB-26 wall mountSurface mount via molded holes at 50 x 50 mm
Installation and connection
Terminals 3 front entry cage clamp terminals (terminals 2 and 3 are bridged)
Terminal sizing Terminals suitable for cables from 0.15 mm2 to 2.5 mm2
Ordering details
Part Description MONI-PT100-NH
PN 140910-000
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
133
Temperature sensor for hazardous areas (Zone 1)
MONI-PT100-EXE
3 wire Pt100 sensor connected to a black glass fiber reinforced polyester junction box (IP65) with 4 front entry cage clamp terminals. M20 EEx e cable gland preinstalled.
Area of use Hazardous environment Zone I
Sensor marking EEx e II T6BASEEFA02ATEX0059X
Sensor
Type Pt100, 3 wire. DIN IEC 751, Class B.
Material: extension cable and tip both stainless steel (MI).
Temperature measuring range –100°C to +500°C
Maximum exposure temp. tip +585°C
Length 2 m
Diameter ca 3 mm, tip ca 5 mm
Minimum bending radius extension cable: 20 mm, the measuring tip should not be bended
Enclosure
Material Glass fiber reinforced polyester (black)
Ingress protection IP65
Dimensions With= 80 mm Height = 75 mm Depth = 55 mm
Cable entry M20 ( EEx e) suitable for cable diameters ranging from 10 mm to 14 mm
Operating temperature –50°C to +55°C
Sealing gasket material tongue and groove system with silicone seal
Cover screws Stainless steel M4 threaded
Mounting For pipe mount use JB-SB-26 wall mountSurface mount via molded holes at 68 x 45 mm
Installation and connection
Terminals 4 front entry cage clamp terminals
Terminal sizing suitable for cables from 0.5 mm2 to 2.5 mm2
Ordering details
Part Description MONI-PT100-EXE
PN 967094-000
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
134
3 Wire PT100 sensor with 4 to 20 mA transmitter for hazardous area (Zone 1)
MONI-PT100-4/20MA
PT100 sensor connected to a 4-20 mA transmitter built in a black glass fiber reinforced polyester junction box with M20 cable gland (Blue).
Area of use Hazardous environment Zone I
Sensor marking EEx ia IIC T6CESI 02 ATEX 115BASEEFA03ATEX0201UPTB 01 ATEX 1061 U
Sensor
Type Pt100, 3 wire. DIN IEC 751, Class B.
Material extension cable and tip both stainless steel (MI).
Temperature measuring range: –50°C to +250°C (transmitter)
Maximum exposure temp. tip +585°C
Length 2 m.
Diameter ca 3 mm, tip ca 5 mm
Minimum bending radius extension cable: 20 mm, the measuring tip should not be bended
Enclosure
Ingress protection IP65
Material Glass fiber reinforced polyester (black)
Dimensions With= 80 mm Heigth = 75 mm Depth = 55 mm
Cable gland M20, blue ( EEx e) suitable for cable diameters ranging from 10 mm to 14 mm
Operating temperature –20°C to +55°C
Sealing gasket material tongue and groove system with silicone seal
Cover screws Stainless steel M4 threaded
For pipe mounting use JB-SB-26
Installation and connection:
Terminals 2 screw terminals
Terminal sizing suitable for cables from 0.5 mm2 to 1.5 mm2
Ordering details
Part Description MONI-PT100-4/20MA
PN 704058-000
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
135
Temperature sensor without junction box forhazardous area (Zone 1)
MONI-PT100-EXE-SENSOR
Certified EEx e II cable gland preinstalled on the sensor lead (M16, Brass, inclusive sealing washer, locknut and earth tag
Area of use Hazardous environment Zone I
Sensor marking EEx e IIBASEEFA03ATEX0201U
Sensor
Type Pt100, 3 wire. DIN IEC 751, Class B.
Material Stainless steel (MI).
Temperature measuring range –100°C to +500°C
Maximum exposure temperature +585°C
Length 2 m
Diameter extension cable ca 3 mm, tip ca 5 mm
Minimum bending radius extension cable: 20 mm, the measuring tip should not be bended
Installation and connection
M16 (Brass) compression gland pre-installed on the sensor.
Sealing washer, earth tag and locknut included.
Maximum operating temperature –50°C to +55°C(for the gland)
Ordering details
Part Description MONI-PT100-EXE-SENSOR
PN 529022-000
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
136
DET-3000
Hand held cable fault locator
Key features
• Easy single-handed operation• Light Hand-held instrument for long and short range applications• Usable for high variety of metallic cables• Cable attenuation compensation and narrow pulse for clear and
simple trace display• Large, high resolution display• Back lit LCD effective down to –20°C• Tactile push buttons• Proven durability
The DET-3000 is a cable fault locaterworking on the principles of Time DomainReflectrometry or TDR. The DET-3000 is a hand held cable fault locater from thelatest generation. The DET-3000 givesgenuine universal performance for shortand long range applications on all types of metallic cable including many types ofheating cable. Innovative features result in a versatile, cable-test instrument that isremarkably easy to use. Large back-lit display, tactile push buttons and ability tooperate in temperatures as low as –20°Callow use in a vast range of locations andconditions. The DET-3000 operates accu-rate to 20 cm on shortest range. Automaticcable attenuation compensation ensureseasy location of faults at all distances.
Principles of operation.If a cable is metal and it has at leasttwo conductors, it can be tested by aTDR. TDRs will troubleshoot and meas-ure all types of cables. The TDR workson the same principle as radar. A pulseof energy is transmitted down the cableunder test. When that pulse reachesthe end of the cable, or a fault alongthe cable, part or all of the pulse energyis reflected back to the instrument. TheTDR measures the time it takes for thesignal to travel down the cable, see theproblem, and reflect back. The TDRthen converts this time to distance anddisplays the information as a waveformand/or distance reading.
The DET-3000 can be used to locateand identify faults in all types of metallicpaired cables including heating cables.TDRs can locate both major or minorcabling problems including; sheathfaults, broken conductors, water dam-age, loose connectors, crimps, cuts,smashed cables, shorted conductors,system components, and a variety ofother fault conditions. In addition, TDRscan be used to test reels of cable forshipping damage, cable shortages,cable usage, and inventory manage-ment. The speed and accuracy of theDET-3000 makes it today's preferredmethod of cable fault location.
Cont
rol a
nd M
onito
ring
DOC-389 Rev.7 07/03
137
Specifications
Ranges (nominal) 10 m, 30 m, 100 m, 300 m, 1000 m, 3000 m
Accuracy ±0.9% of range
Resolution 1% of range
Propagation velocity Variable velocity factor, 0.2 to 0.99 pvfUnit remembers last figure used
Pulse Characteristics With 7ns to 2µs automatically selected to best suit the measuring range
Amplitude 5V nominal when unterminated (SQUARE pulses)
Output Impedance 25 , 50, 75 and 100 Ω switchable
Measuring leads The DET-3000 comes with 100 Ohm testleads
Output sockets 2 x 4 mm on 19 mm pitch
Protection The unit will not be damaged by inadvertent direct connection via the 100 Ohmtestleads to 250Vac. However it is unsafe to use the unit in this way. Installations should always be isolated from the mains supply prior of taking measurements withthe DET-3000. For safety reasons the DET-3000 should not be used on live installations. Always verify prior of starting the measurements that the complete installation is isolated from the mains.
Display Liquid crystal, 128 x 64 pixels with back light
Cursor Single vertical line
Units meters or feet user selectable.
Power 9 VDC nominal6 x AA size LR6 Alkaline batteries (not rechargeable)Battery live ±16 hours @20°C ambient no backlight
Environment Operation Temperature –20°C to +55°C
Storage temperature –30°C to +70
Humidity 93% RH at +40°C
Ingress Protection Water resistant to BS 2011, Part 2.1 R/IEC 68-2-18, Test Ra
Safety EC Directive 73/23/EEC, as amended by 3/68/EECBS EN 41003: 1997
EMC EC Directive 89/336/EEC, as amended by EC directive 93/68/EEC BS EN 50082-1: 1992 BS EN 55011: 1991 (Group 1 Class B)The equipment is specified for operation in residential, commercial and light industrialenvironments.
Size (mm) 250 x 100 x 55 mm
Weight (kg) 1.1 Kg (including batteries, soft-case, testlead, manual)
Ordering Details
Part Description DET-3000
PN 546866-000
DET-3000
Acce
ssor
ies
DOC-389 Rev.7 07/03
138
Support bracket
SB-100
Kit contents
1 support bracket
1 footplate
1 pack containing 2 M4 x 20 cheesehead screw2 M4 nuts2 M4 plain washers2 M4 spring lock washers2 M6 x 30 slotted cheesehead screws2 M6 nuts2 M6 plain washers2 M6 spring lock washers
Support bracket
Material 1.5 mm sheet stainless steel
The support bracket is a three piece construction that is welded together
Surface treatment
Chemically passivated
Dimensions
Dimensions are shown on the drawing below with the tolerance of ± 0.5 mm.
Ordering details
Part Description SB-100
PN 192932-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
139
Dimensions (in mm)
SB-100
150
4960
45
30
42
393861
111111,5 42
115126
160
∅ 7 12×
∅ 7 4×34
∅ 5 4×
∅ 3,2 4×
147
147
10
6,5
25
50 5770
105
46
87
87
25
65
117
60
173
46
25
R 10
40
100
146
40
25
6,75 1,5
1,5
∅ 7 4×
230
20201,5
45,47
9
160°
10,05
100
Application SB-100
AT-TS-13 •AT-TS-14 •JB-16-02 •JB-81 •JB-82 •JB-EX-04 •JB-EX-20 •JB-EX-21 •JB-EX-27 •JB-EX-28 •JBU-100-E •JBU-100-EP •LL-LIM-P-01 •MONI-PT100-EXEMONI-PT100-NHRAYSTAT-CONTROL-10 •RAYSTAT-EX-02 •RAYSTAT-EX-03 •RAYSTAT-ECO-10 •
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
140
Support bracket
SB-101
Kit contents
1 support bracket
1 pack containing 2 M4 x 20 cheesehead screw2 M4 nuts2 M4 plain washers2 M4 spring lock washers
1 pack containing 2 M6 x 30 slotted cheesehead screws2 M6 nuts2 M6 plain washers2 M6 spring lock washers
Support bracket
Material 1.5 mm sheet stainless steel
The support bracket is a two piece construction that is welded together
Surface treatment
Chemically passivated
Dimensions
Dimensions are shown on the drawing below with the tolerance of ± 0.5 mm.
Ordering details
Part Description SB-101
PN 990944-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
141
Dimensions (in mm)
SB-101
160
160
140
140
110
148
140
110
39
105 1,5
90
85
56
1
40
2
158,
5
120
40
R3
R50
2
146
Applications SB-101
AT-TS-13 •AT-TS-14 •JB-16-02 •JB-81 •JB-82 •JB-EX-04 •JB-EX-20 •JB-EX-21 •JB-EX-27 •JB-EX-28 •JBU-100-E •JBU-100-EP •LL-LIM-P-01 •MONI-PT100-EXEMONI-PT100-NHRAYSTAT-CONTROL-10 •RAYSTAT-EX-02 •RAYSTAT-EX-03 •RAYSTAT-ECO-10 •
160
1
2
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
142
Support bracket
SB-110
Kit contents
1 support bracket
1 pack containing 2 M4 x 20 cheesehead screw2 M4 nuts2 M4 plain washers2 M4 spring lock washers2 M6 x 30 slotted cheesehead screws2 M6 nuts2 M6 plain washer2 M6 spring lock washers
Support bracket
Material 2 mm sheet stainless steel
The support bracket is a two piece construction that is spotwelded together
Surface treatment
Chemically passivated
Dimensions
Dimensions are shown on the drawing below with the tolerance of ±0.5 mm.
Ordering details
Part Description SB-110
PN 707366-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
143
Dimensions (in mm)
SB-110
50
43 2
13011511090706845
115
13020
1109070684510
6
5082
R 10
∅ 6.5
∅ 5
6.5 (4x)
230
135°
2
59
50
∅ 7
Application SB-110
AT-TS-13 •AT-TS-14 •JB-16-02 •JB-81 •JB-82 •JB-EX-04 •JB-EX-20 •JB-EX-27JB-EX-28 •JBU-100-EJBU-100-EPLL-LIM-P-01MONI-PT100-EXE •MONI-PT100-NH •MONI-PT100-4/20MA •RAYSTAT-CONTROL-10RAYSTAT-EX-04RAYSTAT-ECO-10RAYSTAT-EX-02 •RAYSTAT-EX-03
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
144
Support bracket
SB-111
Kit contents
1 support bracket
1 pack containing 2 M4 x 20 cheesehead screw2 M4 nuts2 M4 plain washers2 M4 spring lock washers2 M6 x 30 slotted cheesehead screws2 M6 nuts2 M6 plain washers2 M6 spring lock washers
Support bracket
Material 2 mm sheet stainless steel
The support bracket is a two piece construction that is spotwelded together
Surface treatment
Chemically passivated
Dimensions
Dimensions are shown on the drawing below with the tolerance of ± 0.5 mm.
Ordering details
Part Description SB-111
PN 579796-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
145
Dimensions (in mm)
SB-111
13011511090706845
115
130
1109070684510
6
5082
R 10
∅ 6.5
∅ 5
6.5 (4x)
100
98
20
2
∅ 7
R 5035
13040
40
2
R 3
Application SB-111
AT-TS-13 •AT-TS-14 •JB-16-02 •JB-81 •JB-82 •JB-EX-04 •JB-EX-20 •JB-EX-27JB-EX-28 •JBU-100-EJBU-100-EPLL-LIM-P-01MONI-PT100-EXE •MONI-PT100-NH •MONI-PT100-4/20MA •RAYSTAT-CONTROL-10RAYSTAT-ECO-10RAYSTAT-EX-02 •RAYSTAT-EX-03RAYSTAT-EX-04
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
146
Support bracket
SB-120
Kit contents
1 support bracket
1 pack containing 4 M6 x 30 slotted cheesehead screws4 M6 nuts4 M6 plain washers4 M6 spring lock washers
Support bracket
Material 2 mm sheet stainless steel
Making Die stamped: SB-120
Surface treatment
Chemically passivated
Dimensions
Dimensions are shown on the drawing below with the tolerance of ± 0.5 mm.
Ordering details
Part Description SB-120
PN 165886-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
147
Dimensions (in mm)
SB-120
Application SB-120
T-M-20-S/+x-y/EX •T-M-20-S/+x+y •
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
148
Support bracket
JB-SB-26
Pack contents 1 Support Bracket4 M4 x 20 mm cheesehead screws4 M4 nuts4 M4 washers
Support Bracket
Material Grade 316 stainless steel toBS 1449: Part 2: 1983
Marking Die stamped JB-SB-26
Ordering details
Part description JB-SB-26
PN 338265-000
Pack size 1 per pack
Requires two pipe straps (not supplied) Refer to page 150 (Pipe straps)
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
149
Dimensions (in mm)
JB-SB-26
45
456880
100
5 ∅12 places
30
2
50
6880
50
50
3
Application JB-SB-26
MONI-PT100-NH •MONI-PT100-EXE •MONI-PT100-4/20MA •
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
150
Pipe straps Metal straps for pipe mounting of integrated power connections, above the insulationtees and end seals as well as support brackets and the tubular insulation entry.Banding: stainless steel
Pipe outer diameter in mm (inches) Pipe strap PN
20-47 (1/2" - 11/4") PSE-047 700333-000
40-90 (11/4" - 3") PSE-090 976935-000
60-288 (2" - 10") PSE-280 664775-000
60-540 (2" - 20") PSE-540 364489-000
HARD-SPACER-SS-25MM-25M Stainless steel spacer for fixing the heating cable on walls, tanks and vessels, etcWidth spacer: 12.5 mmFixing distance for cables: each 25 mmLength: 25 m/rollPN 107826-000
Warning labels indicate the presence of electrical trace-heating under the insulation ofthe pipe or other equipment. (min. of 1 label per 6 m of trace-heating line)
Language Label reference PN
Croatian ETL-HR 938764-000
Czech ETL-CZ 731605-000
Danish ETL-DK C97690-000
Dutch LAB-I-23 749153-000
English LAB-I-01 938-947-000
Finnish LAB-ETL-SF 756479-000
French LAB-I-05 883061-000
German / French / Italian LAB-ETL-CH 148648-000
German ETL-G 597779-000
Hungarian LAB-ETL-H 623725-000
Italian ETL-I C97688-000
Latvian LAB-I-32 841822-000
Lithuanian LAB-ETL-LIT 105300-000
Norwegian ETL-N C97689-000
Norwegian / English LAB-ETL-NE 165899-000
Polish ETL-PL 258203-000
Portugese LAB-ETL-POR 945960-000
Romanian ETL-RO 902104-000
Russian LAB-ETL-R 574738-000
Slovenian ETL-SLO 538156-000
Spanish ETL-Spanish C97686-000
Swedish LAB-ETL-S 691703-000
Warning labels
AccessoriesR
Acce
ssor
ies
DOC-389 Rev.7 07/03
151
Accessories
Glands 3/4" NPT power cable gland for RAYSTAT-EX-02 (EEx d II C)Nickel plated brassFor use with armoured power cables with outer sheath diameterof 12 mm - 21 mm and inner sheath diameter of 8.5 mm - 16 mmPN 493217-000
GL-33
3/4" NPT power cable gland for RAYSTAT-EX-02 (EEx d II C)Nickel plated brassFor use with non-armoured power cables with outer sheathdiameter of 8.5 mm - 16 mm.PN 931945-000
GL-34
M25 power cable gland (EEx e)PolyamideFor use with non-armoured power cables with outer diameterrange 8 mm - 17 mmSpare part for JBS-100, JBM-100 and JBU-100PN 774424-000
GL-36-M25
GS-54
ATE-180
* Power output of selfregulating heating cables might increase when installed with aluminium tape or other heat transfer aids. Please use TraceCalc or contact your Tyco Thermal Controls representative for further details.
Protective grommet Silicone grommet that protects the heating cable at sharp edgessuch as endplates of insulation cladding, flanges etc. It can becut-to-length and resists temperatures up to 215°C.PN 412549-000
G-02
Aluminium tape* for attaching heating cables and thermostat sensors to pipes and tanks. Minimum installation temperature: 0°C55 m per roll, 63.5 mm widthPN 846243-000
Thermostat kit Kit with supplementary terminals to connect thermostats of typeRAYSTAT-EX-02 to the junction boxes JBS, JBM and JBU.The kit includes 2 terminals WAGO 284 series (1 x L, 1 x PE), 1 power cable gland GL-36-M25, 1 end plate and 1 installationinstructionPN 966659-000
HWA-WAGO-TSTAT-KIT
Glass cloth tape for attaching heating cable to pipe. For stainless-steel pipes or for any installation below 4.4°C.16 m per roll, 12 mm widthPN C77221-000
Fixing tapes Self-adhesive tape for fixing the heating cables on pipes or other equipment.
GT-66 Glass cloth tape for attaching heating cable to pipe. Not for stainless-steel pipes or for installation temperatures below 4.4°C.20 m per roll, 12 mm widthPN C77220-000
R
Acce
ssor
ies
DOC-389 Rev.7 07/03
152
R Accessories
Adaptors
REDUCER- M25 (female) to Pg16 (male) reducer (EEx e)M25/PG16-EEXE Polyamide, ATEX approved reducer with captive sealing ring
(“o”-ring)For use with cables with outer diameters up to 13 mmPN 953780-000
ADPT-PG16- Pg16 (female) to M25 (male) adaptor (EEx e)M25-EEXE Polyamide, ATEX approved adaptor with captive sealing ring
(“o”-ring)For use with cables with outer diameters up to 15 mmPN 541892-000
M25 power cable gland (EEx e II and EEx d II C) for use withjunction boxes with internal earth plate (-EP) or metal boxes.For use with armoured power cables with sheath diameter of 12 mm - 21 mm and inner sheath diameter of 8.5 mm - 16 mm. PN 056622-000
GL-38-M25-METAL
REDUCER- M25 (male) to M20 (female) reducer EExdM25/20-EEXD Brass, ATEX approved reducer with captive sealing ring
(“o”-ring)PN 404287-000
REDUCER-M32/ M32 (male) to M25 (female) reducer (EEx e)M25-EEXE ATEX approved reducer. Polyamide.
PN 1244-000 859
ADPT-M20/25- M20 (male) to M25 (female)EEXD Brass, ATEX approved adaptor with captive sealing ring
(“o”-ring)For use with cables with outer diameters up to 14 mmPN 684953-000
REDUCER- M25 (male) to M20 (female) reducer EExd including a locknutM25/20 and fibre washer
Brass, ATEX approved reducer with captive sealing ring (“o”-ring)PN 630617-000
REDUCER-M25/ M25 (male) to M20 (female) reducer M20-PA Polyamide, ATEX approved reducer with captive sealing ring
(“o”-ring)Ordinary areaPN 184856-000
Adaptors
Cable gland EExe (M20), polyamide for use with PI cables witha diameter range of 5-13 mm. With green / yellow sleeve.PN 1244-000 848
GL-44-M20-KIT
GL-45-M32 Cable gland EExe (M32), polyamide for use with power cableswith a diameter range of 12-21 mm.PN 1244-000 847
Acce
ssor
ies
DOC-389 Rev.7 07/03
153
Plugs
HWA-PLUG-M25- M25 stopping plugEXE-PLASTIC Polyamide
Spare part for JBS-100, JBM-100, JBU-100PN 434994-000
Small pipe adaptors with part number
R Accessories
Transmitter TCONTROL-ISOL-01 Isolator for MONI-PT100-4/20MAGalvanically isolated module for EEx ia protection of MONI-PT100-4/20MA sensor between the hazardous area and the ordinary area. Surface or DIN 35 rail mounted. A seperate 24 Vdc power supply such as MONI-RMC-PS24 is required. PN 670021-000
Power supply MONI-RMC-PS24 24 Vdc power supplyWide range input (100-240 Vac) power supply to provide 24 Vdc input for MONI-RMC-BASE or TCONTROL-ISOL-01 products. Surface or DIN 35 rail mounted.PN 972049-000
JBS-SPA Small pipe adaptor required for pipes ≤ 1” (DN25),applicable for JBS-100, E-100, E-100-LE90515-000 (bag of 5 adaptors)
JBM-SPA Small pipe adaptor required for pipes ≤ 1” (DN25), applicable for JBM-100, T-100E55673-000 (bag of 5 adaptors)
HWA-PLUG-M20- M20 stopping plug EExe PolyamideSpare part for various junction boxes.PN 1244-000 845
EXE-PLASTIC
Technical Databook for Industrial heating system
s2003 / 2004 Edition
Technical Databook for Industrial Heating Systems
2003 / 2004 Edition
Important: All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability ofeach product for their particular application. Tyco Thermal Controls makes no warranties as to the accuracy or completeness of the informa-tion, and disclaims any liability regarding its use. Tyco Thermal Controls’ only obligations are those in the Tyco Thermal Controls StandardTerms and Conditions of Sale for this product, and in no case will Tyco Thermal Controls or its distributors be liable for any incidental, indi-rect or consequential damages arising from the sale, resale, use or misuse of the product. Specifications are subject to change without notice.In addition, Tyco Thermal Controls reserves the right to make changes, without notification to the Buyer, to processing or materials that donot affect compliance with any applicable specification.
DigiTrace, Isopad, Raychem, RAYSTAT and Tracer are trademarks of Tyco Electronics.Cage clamp is a trademark of WAGO.
This document was supplied to you by:
www.tycothermal.com
Our products satisfy the requirements of the relevant European Directives.
©19
98 T
yco
The
rmal
Con
trol
s D
OC
-389
R
ev.7
07
/03
Prin
ted
in B
elgi
um o
n ch
lorin
e-fr
ee b
leac
hed
pape
r.
België / BelgiqueElectrical TracingGeestbeekweg 53210 LubbeekTel. (016) 35 39 90Fax (016) 25 27 26
BulgariaERZET EngineeringKompl. Bratja Miladinovi/bl57/vch.4ABG-8000 BurgasTel./fax (56) 3 4198Mobile (88) 639 903Fax (UK) +44 8701368787
Çeská RepublikaRaychem HTS s.r.o.Novodvorská 8214200 Praha 4Phone 241 009 215Fax 241 009 219
DanmarkTyco Thermal Controls Nordic ABStationsvägen 4S-430 63 HindåsTel. 80 88 29 92Fax 80 88 29 91
DeutschlandTyco Thermal Controls GmbHEnglerstraße 1169126 HeidelbergTel. (0 62 21) 30 43-0Fax (0 62 21) 30 43-43
EspañaTracelecC/Josep V. Foix, 10Apdo. 1326-4308043007 TarragonaTel. (34) 977 290 039Fax (34) 977 290 032
FranceTyco Thermal Controls SAB.P. 73895004 Cergy-Pontoise CedexTél. (01) 34 40 73 30Fax (01) 34 40 73 33
HrvatskaELGRI d.o.o.S. Mihalica 210000 ZagrebTel. (1) 6050188Fax (1) 6050187
ItaliaTyco Electronics Raychem SPACentro Direzionale MilanofioriPalazzo E520090 Assago, MilanoTel. (02) 57 57 61Fax (02) 57 57 62 01
Lithuania/LatviaV. DemjanovPavenciu Str. 39-225500 LT MazheikiaiTel. (9) 841156Fax (9) 396272
MagyarországRaychem Ges.m.b.H.Magyarországi Közvetlen KépviseletGrassalkovich ut 255.1239 BudapestTel. (1) 289 20 40Fax (1) 289 20 45
NederlandTyco Thermal Controls b.v.Van Heuven Goedhartlaan 1211181 KK AmstelveenTel. (020) 6400411Fax (020) 6400469
NorgeTyco Thermal Controls Norway ASMalerhaugveien 25Postboks 6076 - Etterstad0602 OsloTel. +47 66 81 79 90Fax +47 66 80 83 92
ÖsterreichTyco Thermal Controls N.V. LubbeekOffice WienBrown-Boveri Strasse 6/142351 Wiener NeudorfTel. (0 22 36) 86 00 77Fax (0 22 36) 86 00 77-5
PolskaRaychem Polska Sp. z o.o.Tyco Thermal Controlsul. Farbiarska 69 C02-862 WarszawaTel. (022) 54 52 950Fax (022) 54 52 951
RomaniaSantel Impex Srl.Str C-tin Radulescu Motru Nr6Bl. 35, Sc C, Ap 117, Sect 475164 BucurestiTel. (1) 330 7199/2591Fax (1) 330 1229/2591
Schweiz / SuisseTyco Thermal Controls N.V.Office BaarHaldenstrasse 5Postfach 27246342 BaarTel. (041) 766 30 80Fax (041) 766 30 81
SuomiTyco Thermal Controls Nordic ABStationsvägen 4S-430 63 HindåsPuh. 0800 11 67 99Telekopio 0800 11 86 74
Sverige Tyco Thermal Controls Nordic ABStationsvägen 4S-430 63 HindåsTel. 0301-228 00Fax 0301-212 10
TürkiyeHENA Ltd.Ressam Vecih Bereketoglu SokakCandan Ap. No 8/1Caddebostan 81060 Kadiköy, IstanbulTel. (216) 363 1212Fax (216) 360 3816
United KingdomTyco Thermal Controls (UK) Ltd3 Rutherford RoadStephenson Industrial EstateWashington, Tyne & WearNE37 3HX, United KingdomTel. 44 (191) 419 8200Fax 44 (191) 419 8201
ROSSIÅ i drugie strany SNGRAJXEM125315, g. MoskvaLeningradskij prospekt, dom 72,ofis 807Tel.: (095) 7211888Faks: (095) 7211891
YugoslaviaMinel-KeyingDositejeva 24YU 23300 KikindaTel. (230) 34519Fax (230) 23479
R
R