+ All Categories
Home > Documents > Surveying Lab11111111111

Surveying Lab11111111111

Date post: 03-Jun-2018
Category:
Upload: andytatte32
View: 220 times
Download: 0 times
Share this document with a friend

of 23

Transcript
  • 8/12/2019 Surveying Lab11111111111

    1/23

    1

    SURVEYING LAB-

    INDEX

    INTRODUCTION &LIST OF EQUIPMENTS.

    1. SURVEY OF AN AREA BY CHAIN SURVEY (CLOSED TRAVERSE) & PLOTTING.

    2. CHAINING ACROSS OBSTACLES.

    3. DETERMINE OF DISTANCE BETWEEN TWO INACCESSIBLE POINT WITHCOMPASS.

    4. SURVEY OF A GIVEN AREA BY PRISMATIC COMPASS (CLOSED TRAVERSE)AND PLOTTING AFTER ADJUSTMENT.

    5. RADIATION METHOD, INTERSECTION METHODS BY PLANE TABLE SURVEY.

    6. TWO POINT AND THREE POINT PROBLEMS IN PLANE TABLE SURVEY.

    7. TRAVERSING BY PLANE TABLE SURVEY.

    8. FLY LEVELING (DIFFERENTIAL LEVELING).

    9. AN EXERCISE OF L.S AND C.S AND PLOTTING.

    10. TWO EXERCISE ON CONTOURING.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    2/23

    2

    1. SURVEY OF AN AREA BY CHAIN SURVEY (CLOSED TRAVERSE)AND PLOTTING.

    AIM;- To Carry out survey of an area by chain survey and plot the same.

    APPARATUS;- chain ,tape ,cross staff ,ranging rods ,arrows.

    PROCEDURE;-

    1. This survey is carried out to locate the boundaries of a field and to determine its area.2. A chain line is run through the center of area which divided into a no. of Triangles andtrapezoids.3. The offsets to the boundary are taken in order to their chainages as shown.

    4. After the field work is over the survey is plotted to a suitable scale.5. Then the area of a field is calculated as shown in tabular column

    CALCULATIONS;-S.NO Name of

    figureChainage

    (m)Base(m)

    Offsets(m)

    Mean(m)

    Area(m2)

    RESULT;- Total area of field=

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    3/23

    3

    2. CHAINING ACROSS OBSTACLES.

    AIM;- To measure distance between two points by chaining across different types of Obstaclesencountered by indirect method.

    APPARATUS;- Chain, tape, cross-staff , ranging rods, arrows.

    PROCEDURE;-Obstacles to chaining prevent chainmen to measuring directly between Twopoints and give rise to a set of problems in which distances are found by indirect Measurements.

    1. Obstacles to chaining are of three kinds.2. Obstacles to ranging but not chaining.E.x (High level ground)

    3. Obstacles to chaining but not ranging. E.x(Pond,river)4. Obstacles to both chaining and ranging. E.x(building)

    A) OBSTACLES TO RANGING BUT NOT CHAINING;-This type of problem comes, when a rising ground or a forest area interrupts the chain line.

    The end station are not inter visible

    1. Both ends of line may be visible from intermediate points on line.2. Both ends of line may not be visible from intermediate points on line.

    CBoth the stations are visible from intermediate points on the line1. In this case reciprocal ranging is adopted and chaining is done by stepping method2. A and B are two end stations, which are not inter visible due to a hill in between them.3. Select two intermediate points Pl and Ql, such that from each station point A and B are

    visible.4. Two persons take up the positions Pl and Q l with ranging rods.5. First the person standing at Pl directs the person at Ql to come in line of PlB, and his new

    position will be Q2.6. Now, the person standing at Q2, directs the person at pi, to come in line of Q2A, and his

    new position will be P2.

    7. Now, the person standing at P2, directs the person at Q2, to come in line of P2B, and hisnew position will be Q3.8. This process is continued until the intermediate points P and Q are located in such a way

    that the person standing at P, see Q and B in the line, and the person standing at Q, see Pand A in the line.

    9. Distance AB = AP+PQ+QB

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    4/23

    4

    The end stations are not visible from the intermediate points on the line:1. This is the case when trees ,bushes or jungle comes across the chain line2. In this case the method of random line is most suitable

    1. In fig let PQ be the line in which P and Q are not visible from intermediatePoint on it.2. Through P draw a random line PQ in any convenient direction but as nearly to Towards

    Q as possible.3. The points Q should be so chosen that, Q1is visible from Q and Q,Q1 is in random Line.4. Measure QQ1 select points S1and R1on random line and erect perpendicular SS1 and

    RR1on it.5. Make SS1= PS1/PQ1x QQ1And RR1= PR1/PQ1x QQ16. Join SR and prolong.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    5/23

    5

    B) OBSTACLES TO CHAINING BUT NOT RANGING:-There may be two cases of this obstacle.1. When it is possible to chain round the obstacle. i.e. A POND.

    2. When it is not possible to chain round the obstacle. i.e. A RIVER.

    CASE (1);- Following are the methods.Method (a);-

    1. Select two points A AND B on either side.2. Set out equal perpendicular AC and BD as shown in fig (a)3. Measure CD=AB.

    Method (b);-1. set out AC perpendicular to chain line as shown in fig (b)2. Measure AC and BC3. The length AB is calculated from the relation

    AB=BC-AC

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    6/23

    6

    Method (c);1. By cross staff find a point C .which subtends 90 with A and B as Shown in fig (C). AC

    and BC.2. The length AB is calculated from relation AB= AC+BC.

    Method (d);-1. select any point E and range C in line with AE, making AE =EC2. Range D in line with BE and make BE=ED as shown in fig (d).3. Measure CD then AB=CD.

    CASE (2); -Following are the methods.

    Method (a1. select point B on one side and A and C on the other side.

    2. Erect AD and CE as perpendicular to AB and range B,D and E in One line as shown infig (e).3. Measure AC, AD and CE.4. If a line DF is drawn parallel to AB cutting CE in F perpendicularly The triangle ABD

    and FDE will be similar.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    7/23

    7

    Method (b):1. Locate a point R in such a way that it makes 900with PQ.2. Range S in line with PR and make PS = PR.3. At S erect a perpendicular ST to cut the line AB at T.4. Then PQ =PT

    C) OBSTACLES TO BOTH CHAINING AND RANGING;-

    A Building is the typical example of this type of obstacles. The problem liesIn prolonging the line beyond the obstacle and determine the distance across it.

    Method (a);-1. Choose two points A and B to one side erect perpendicular AC and BD of equal length.2. Join CD and prolong It pass the obstacles.3. Choose two points E and F on CD and erect perpendicular EG and FH equal to AC or BD

    as shown in fig (g).4. Join GH and prolong it. Measure DE.5. BG=DE.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    8/23

    8

    Method (b);-1. select a point A and erect a perpendicular AC of any convenient Length.2. Select another point B on chain line such that AB=AC.3. Join B and C and prolong it. To any convenient point D.

    4. At D set a right angle DE such that DE=DB.5. Choose another point F on DE such that DF=DC with F as centre and AB as radius. Drawan arc with E as center draw another arc of same Radius to cut previous arc in G

    6. Join GE which will be in range with chain line. Refer the fig (h)7. Measure CF then AG=CF.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    9/23

    9

    3. DETERMINATION OF DISTANCE BETWEEN TWO INACCESSIBLE

    POINTS WITH COMPASS.

    AIM;- TO determine distance between two inaccessible points with compass.

    APPARATUS;-Prismatic compass, arrows, tape, ranging rods, pegs.

    PROCEDURE;-If there is an obstacle between two points say A and B due To which directdistance measurement is not possible the those points are called As inaccessible points anddistance between them is to be determined indirectly

    By following the procedure described below.1. Let us say the inaccessible distance required is AB fig (a).2. Select line CD approximately parallel to AB of known length.

    3. Place prismatic compass at point C and center it and see to it that is parallel to Groundsurface.4. Measure bearing of line CA,CB and CD.5. Then shift compass to point D and in similar way measure bearings of lines DA, DB and

    DC.from observed bearing.6. Calculate the interior angles 1, 2, 3, 4 .from properties of triangle .calculate Angles 5

    and 6. Consider Triangle ADC and applying sine rule. We get AC/Sin3=CD/Sin5=AD/Sin (1+2)

    7. Calculate AC and AD.8. Link wise consider triangle BCD and apply sine rule. BC/Sin (3+4) =CD/Sin6

    =BD/Sin2 BC and BD.

    9. Then consider triangle ABC and apply cosine rule.a. AB=D=BC+AC - 2 XAC XBC XCOS1.

    b. AB=D=AD+BD -2 XAD XBD XCOS4.

    By considering triangle ABC

    Bearing; -Angle measured with reference to north.

    ANGLE;-Angle made by the two lines

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    10/23

    10

    4. SURVEYING OF AN GIVEN AREA BY PRISMATIC COMPASS

    (CLOSED TRAVERSE) AND PLOTTING AFTERADJUSTMENT.

    AIM;-To run a closed traverse by prismatic compass and plot the same.

    APPRATUS; - Prismatic compass, tape, chain, arrows, pegs, ranging rods.

    PROCEDURE;- Closed traverse is generally run around a structure .It is defined asA series of connected lines whose directions and lengths are determined precisely.

    Following procedure is adopted to run a closed compass traverse.1) Let us say we have to run a closed compass traverse ABCDEA.

    2) Set the prismatic compass at point A. center it and level it.3) Take bearings of traverse lines AB and AE.4) shift the compass to point B center it and level it. Take the bearings BC and BA.5) Link-wise complete the traverse as shown in fig (a).6) Measure the length of traverse line AB, BC, CD, DE, and EA.7) Record the observation in tabular columns.8) Care must be taken to see that the stations are not affected by local attractions. If they are

    affected corrections to local attractions should be applied first andThen the traverse should be plotted with corrected bearings.

    9) Simplest method of plotting is angle and distance method with a protractor. IfLast point is falling short by some distance in meeting the first point then it

    Means that there is a closing error.10) So, traverse should be adjusted by Bow ditchs graphical method.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    11/23

    11

    Calculations;-

    LINE FORE BEARING BACK BEARING LENGTH(M)

    RESULT;- The adjusted traverse with bearings and length is to be shown on aDrawing sheet.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    12/23

    12

    5. RADIATION METHOD AND INTERSECTION

    METHOD BY PLANE TABLE SURVEY.

    AIM;- To locate the details by radiation method and intersection method.

    APPARATUS; -plain table, tripod, chain, tape, alidade, sprit level, plumbing forkRanging rods, pegs, trough compass.

    PROCEDURE:-

    (A) RADIATION METHOD;-* In this method objects can be located from a single station.*In this method rays are drawn from the single station to objects.

    *The distance from the station to object are measured and plotted toany suitable scale along the respective rays.*This method is suitable for small areas of survey.

    The following is the procedure of radiation method for plane table survey.1) Select P as a station on the ground.2) From the station P the objects A, B, C and D are visible.3) Set up table over station P and level and center.4) Clamp the table.5) A point p is selected on the sheet to represent the

    Station P.

    6) With the Trough compass the North line is marked on the right hand topCorner of the sheet.7) With the alidade touching p,the ranging rods A,B,C,and D are bisected and

    The rays drawn.8) The distances PA, PB, PC and PD are measured by means of a tape or chain.9) The distances are plotted to suitable scale to obtain the points a, b, c and d.

    Representing the objects A, B, C, and D on the sheet.10) Suitable scale is chosen based on the length of longest line11) The method is suitable to locate small defaults12) The method is suitable to calculate the area of a land.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    13/23

    13

    (B)INTERSECTION METHOD;-Suitability;-* In this method Object can be located by Intersections of the Rays drawn from

    Two Instrument stations.* This method is suitable for locating inaccessible object points.* The line joining two stations is the base line.* This method is suitable when it is difficult or impossible to measure distances

    As in mountainous area.* This method is also used for checking distant objects.

    PROCEDURE;-

    1) A and B are two stations and P is inaccessible object on the far bank of aRiver.2) Now it is required to locate position of P on the sheet by intersection of rays,

    drawn from A and B.3) Select two stations A and B, so that the P point to be plotted is visible from both

    A and B stations.4) The table is setup at A and levelled.5) The table is levelled with the help of spirit level and centered by U fork so

    that a point a on the sheet is just over the station A.6) The North line is marked on the right side top corner by trough Compass, then

    table is clamped

    7) With the Alidade touching a the ranging rod at B and the object at P arebisected and rays are drawn through the fiducial edge of Alidade8) The distance AB is measured and plotted to any suitable scale to obtain the point

    b9) The table is shifted centered over B and leveled properly .

    10) The Alidade touching b is placed along the line ba11) Orientation is done by back sighting. At this time it should be remembered

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    14/23

    14

    that the centering, leveling and Orientation must be done again if necessary.12) The Alidade touching b the object P is bisected and ray is drawn .Let this

    ray intersects the previous ray at a point p on drawing sheet.13) This point p is the required inaccessible plotted position of P.

    RESULT; -The result of above methods are presented in drawing sheet.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    15/23

    15

    6. TWO POINT AND THREE POINT PROBLEMS IN

    PLANE TABLE SURVEY.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    16/23

    16

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    17/23

    17

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    18/23

    18

    7. TRAVERSING METHOD BY PLANE TABLE

    SURVEY.

    AIM; - To run a close traverse by means of plane table.

    APPARATUS; -Plane table, tripod, chain, tape, alidade, spirit level, trough -compass, plumbing fork, ranging rods, pegs.

    PROCEDURE;-* This method is suitable for connecting the traverse stations.* This method is similar to compass traversing or theodolite traversing.* In this method the plane table set up at each successive station.*It is used for running survey line between stations to locate the topographical details.

    1) The alidade touching the point a and sighting the ranging rod at B, is bisected andray is drawn.2) The distance AB is measured and plotted to suitable scale.3) The table is shifted and centered over B station.4) It is then levelled oriented by back sighting and clamp the table.5) With the alidade touching point b, the ranging rod at C is bisected and a ray isdrawn.6) The distance BC is measured and plotted to same scale.7) The table is shifted and set up at C and the same procedure is repeated.8) In this manner, all the stations of the traverse are connected.

    Note;- At the end the finishing point may not coincide with the starting point and theremay be some closing error.

    RESULT; -Result is shown on drawing sheet.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    19/23

    19

    8. FLY LEVELLING (DIFFERENTIAL LEVELLING).

    AIM;- To ascertain the difference of elevation between any two points.

    APPARATUS; - Dumpy level, leveling staff, tripod.

    PROCEDURE;-

    Differential leveling is the method of direct leveling the object of which is To determinedifference in elevations of two points regardless of horizontal position of point with respect toeach other, when points are apart it may be necessary to setup The instrument several times. Thistype of leveling is also known as FLY-LEVELLING.

    1) Instrument level is setup at a convenient positions near first point (say A).2) Temporary adjustments should be done,(setting up, leveling up, elimination of a par--allox) are performed.

    3) First sight of B.M (point of known elevation) is taken and reading is entered in backSight column.

    4) Then second reading is taken by keeping leveling staff on first point as entered inIntermediate sight column.

    5) If distance is large instrument is shifted, the instrument becomes turning point (or)Changing point.

    6) After setting up instrument at new position, performing temporary adjustment andTake back sight as turning point.

    7) Thus turning point will have both back sight and fore sight readings.8) Link wise the process is repeated till last point (say B) is reached.9) The above procedure is shown in fig. Readings are entered in a tabular form is given

    Below and Reduced levels are calculate either by height of instrument method (or)Rise and fall method.

    ARITHMETIC CHECK;-

    B.S - F.S=RISE - FALL=LAST RL - FIRST R.L

    RESULT;- Difference of elevation between two given points is ______ M.

    SIMPLE LEVELLING

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    20/23

    20

    ST.NO BS (M) I.S(M) F.S(M) HI(M) R.L(M) REMARKS

    RESULT;- Difference between point =________ m.

    DIFFERENTIAL LEVELLING.

    ST.NOS B.S (M) I.S(M) F.S(M) H.I(M) R.L REMARKS

    ARITHMETICAL CHECK;-B.S F.S =Last R.L-First R.L

    RESULT;- Difference of level A and B is = ______m.

    9. PROFILE LEVELLING

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    21/23

    21

    (Longitudinal section & cross section, L.S & C.S)And plotting

    AIM; -Determining the elevation at various points on ground at regular interval.

    APPRATUS;- Dumpy level, leveling staff, tripod, peg.

    Procedure;-1) Divide the proposed center line of a given work at regular intervals2) Fix the level and do station adjustments3) BS on Bench Mark4) IS on intermediate points5) FS on Change points and End point6) Record the values in field book in respective columns

    Profile leveling

    ST.NO Left Centre Right B.S(M) I.S(M) F.S(M) H.I(M) R.L REMARK

    ARITHMETIC CHECK;- B.S F.S = Last R.L First R.L.

    JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITYHYDERABAD

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    22/23

    22

    II YEAR B.TECH. C.E.I SEM T P CA0 4+1* 0 4

    SURVEYING

    UNIT IINTRODUCTION: Overview of plane surveying (chain, compass and plane table), Objectives, Principles andclassifications.

    UNIT II:DISTANCES AND DIRECTION: Distance measurement conventions and methods; use of chain and tape, Electronicdistance measurements, Meridians, Azimuths and Bearings, declination, computation of angle.

    UNIT IIILEVELING AND CONTOURING: Concept and Terminology, Temporary and permanent adjustments- method ofleveling.Characteristics and Uses of contours- methods of conducting contour surveys and their plotting.

    UNIT IVCOMPUTATION OF AREAS AND VOLUMES:Area from field notes, computation of areas along irregular

    boundaries and area consisting of regular boundaries. Embankments and cutting for a level section and two levelsections with and without transverse slopes, determination of the capacity of reservoir, volume of barrow pits.

    UNIT - VTHEODOLITE: Theodolite, description, uses and adjustments temporary and permanent, measurement ofhorizontal and vertical angles. Principles of Electronic Theodolite. Trigonometrical leveling, Traversing.

    UNIT VITACHEOMETRIC SURVEYING:

    Stadia and tangential methods of Tacheometry. Distance and Elevation formulae for Staff vertical position.

    UNIT VIICurves: Types of curves, design and setting out simple and compound curves.

    UNIT - VIIIIntroduction to geodetic surveying, Total Station and Global positioning system, Introduction to Geographicinformation system (GIS).

    TEXT BOOKS:1. Surveying (Vol 1, 2 & 3), by B.C.Punmia, Ashok Kumar Jain and Arun Kumar Jain - Laxmi Publications (P) ltd.,New Delhi2 .Duggal S K, Surveying (Vol 1 & 2), Tata Mc.Graw Hill Publishing Co. Ltd. New Delhi, 2004.3. Surveying and levelling by R. Subramanian, Oxford university press, New Delhi

    REFERENCES:1. Arthur R Benton and Philip J Taety, Elements of Plane Surying, McGraw Hill 20002. Arror K R Surveying Vol 1, 2 & 3), Standard Book House, Delhi, 20043. Chandra A M, Plane Surveying, New age International Pvt. Ltd., Publishers, New Delhi, 2002.

    4. Chandra A M, Higher Surveying, New age International Pvt. Ltd., Publishers, New Delhi, 2002.

    w.jntuworld.com

    www.jntuworld.com

    www.jwjobs.net

  • 8/12/2019 Surveying Lab11111111111

    23/23

    23

    JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITYHYDERABAD

    II YEAR B.TECH. C.E.I SEM T P C0 3 2

    SURVEYING LAB I

    LIST OF EXERCISES :1. Survey of an area by chain survey (closed traverse) & Plotting2. Chaining across obstacles3. Determination of distance between two inaccessible points with compass.4. Surveying of a given area by prismatic compass (closed traverse) and plotting after adjustment.5. Radiation method, intersection methods by plane Table survey6. Two point and three point problems in plane table survey7. Traversing by plane table survey8. Fly leveling (differential leveling)9. An exercise of L.S and C.S and plotting10. Two exercises on contouring.

    List of Major Equipment:

    1. Chains, tapes, Ranging rods, cross staff, arrows2. Compasses and Tripods, Optical square.3. Plane tables, Alidade, Plumbing fork, trough compasses4. Leveling instruments and leveling staves5. Box sextants, planimeter.

    w.jntuworld.com www.jwjobs.net


Recommended