+ All Categories
Home > Documents > SW178WA01 7” alu-cone subwoofer, 8 ohm - Wavecor · For more information please visit...

SW178WA01 7” alu-cone subwoofer, 8 ohm - Wavecor · For more information please visit...

Date post: 13-Sep-2018
Category:
Upload: hakien
View: 213 times
Download: 0 times
Share this document with a friend
2
Specifications are subject to change without any further notice. Copyright © 2009 - 2012 by Wavecor Ltd., Guangzhou, China. All rights reserved. Wavecor ® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com SPECIFICATIONS Page 1 SW178WA01 7” alu-cone subwoofer, 8 ohm SW178WA01 is a woofer designed for dedicated subwoofer applicaons. It works equally well for high-end hi-fi, high quality home theater systems, and top mulmedia setups. FEATURES Very rigid aluminium cone to ensure piston moon at high levels and for beer heat transfer at high connuous power levels Vented voice coil former for reduced distoron and compression Vented center pole with dual flares for reduced noise level at large cone excursions Vented chassis for lower air flow speed reducing audible distoron Heavy-duty black fiber glass voice coil bobbin to reduce mechanical losses resulng in beer dynamic performance and low-level details Large motor system with 1½” voice coil diameter and 110mm magnet for beer control and efficiency Built-in alu field-stabilizing ring for reduced high-level distoron Long linear stroke motor for reduced distoron at high levels Linear suspension with specially designed CONEX damper (spider) for long durability under extreme operang condions 4-layer voice coil for increased control and beer small-cabinet performance Gold plated terminals to prevent oxidaon for long-term reliable connecon Sealing gasket pre-aached for hassle-free mounng and secure cabinet sealing Notes Parameter Before burn-in Aſter burn-in Unit Nominal size 7 [inch.] Nominal impedance 8 [ohm] Recommended max. upper frequency limit 600 [Hz] 1, 3 Sensivity, 2.83V/1m (calculated from T/S parameters) 85 [dB] 2 Power handling, short term, IEC 268-5, no addional filtering [W] 2 Power handling, long term, IEC 268-5, no addional filtering [W] 2 Power handling, connuous, IEC 268-5, no addional filtering 100 [W] Effecve radiang area, S d 131 [cm²] 3, 6 Resonance frequency (free air, no baffle), F s 38 36 [Hz] Moving mass, incl. air (free air, no baffle), M ms 35 [g] 3 Force factor, Bxl 12.0 [N/A] 3, 6 Suspension compliance, C ms 0.50 0.56 [mm/N] 3, 6 Equivalent air volume, V as 12.2 13.6 [lit.] 3, 6 Mechanical Q, Q ms 19.3 18.4 [-] 3, 6 Electrical Q, Q es 0.37 0.35 [-] 3, 6 Total Q, Q ts 0.365 0.346 [-] 4 Voice coil resistance, R DC 6.4 [ohm] 5 Voice coil inductance, L e (measured at 1 kHz) 2.2 [mH] Voice coil inside diameter 39 [mm] Voice coil winding height 16 [mm] Air gap height 6 [mm] Magnet weight 680 [g] Total unit net weight excl. packaging 1.81 [kg] 3, 5 K rm [mohm] 3, 5 E rm [-] 3, 5 K xm [mH] 3, 5 E xm [-] NOMINAL SPECIFICATIONS Note 1 Measured in infinite baffle. Note 2 Tested in free air (no cabinet). Note 3 Measured using a semi-constant current source, nominal level 2 mA. Note 4 Measured at 25 deg. C Note 5 It is generally a rough simplificaon to assume that loudspeaker transducer voice coils exhibit the characteriscs of an inductor. Instead it is a far more accurate approach to use the more advanced model oſten referred to as the “Wright empirical model”, also used in LEAP-4 as the TSL model (www.linearx.com), involving parameters K rm , E rm , K xm , and E xm . This more accurate transducer model is described in a technical paper here at our web site. Note 6 Aſter burn-in specificaons are measured 12 hours aſter exing the transducer by a 20 Hz sine wave for 2 hours at level 14.1 V RMS. . The unit is not burned in before shipping.
Transcript

Specifications are subject to change without any further notice. Copyright © 2009 - 2012 by Wavecor Ltd., Guangzhou, China. All rights reserved.Wavecor® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com

SPECIFICATIONS

Page 1

SW178WA01 7” alu-cone subwoofer, 8 ohm

SW178WA01 is a woofer designed for dedicated subwoofer applications. It works equally well for high-end hi-fi, high quality home theater systems, and top multimedia setups.

FEATURES• Very rigid aluminium cone to ensure piston motion at high levels and for better

heat transfer at high continuous power levels• Vented voice coil former for reduced distortion and compression• Vented center pole with dual flares for reduced noise level at large cone

excursions• Vented chassis for lower air flow speed reducing audible distortion• Heavy-duty black fiber glass voice coil bobbin to reduce mechanical losses

resulting in better dynamic performance and low-level details• Large motor system with 1½” voice coil diameter and 110mm magnet for better

control and efficiency• Built-in alu field-stabilizing ring for reduced high-level distortion• Long linear stroke motor for reduced distortion at high levels• Linear suspension with specially designed CONEX damper (spider) for long

durability under extreme operating conditions• 4-layer voice coil for increased control and better small-cabinet performance• Gold plated terminals to prevent oxidation for long-term reliable connection• Sealing gasket pre-attached for hassle-free mounting and secure cabinet sealing

Notes Parameter Before burn-in After burn-in Unit

Nominal size 7 [inch.]Nominal impedance 8 [ohm]Recommended max. upper frequency limit 600 [Hz]

1, 3 Sensitivity, 2.83V/1m (calculated from T/S parameters) 85 [dB]2 Power handling, short term, IEC 268-5, no additional filtering [W]2 Power handling, long term, IEC 268-5, no additional filtering [W]2 Power handling, continuous, IEC 268-5, no additional filtering 100 [W]

Effective radiating area, Sd 131 [cm²]3, 6 Resonance frequency (free air, no baffle), Fs 38 36 [Hz]

Moving mass, incl. air (free air, no baffle), Mms 35 [g]3 Force factor, Bxl 12.0 [N/A]

3, 6 Suspension compliance, Cms 0.50 0.56 [mm/N]3, 6 Equivalent air volume, Vas 12.2 13.6 [lit.]3, 6 Mechanical Q, Qms 19.3 18.4 [-]3, 6 Electrical Q, Qes 0.37 0.35 [-]3, 6 Total Q, Qts 0.365 0.346 [-]

4 Voice coil resistance, RDC 6.4 [ohm]5 Voice coil inductance, Le (measured at 1 kHz) 2.2 [mH]

Voice coil inside diameter 39 [mm]Voice coil winding height 16 [mm]Air gap height 6 [mm]Magnet weight 680 [g]Total unit net weight excl. packaging 1.81 [kg]

3, 5 Krm [mohm]3, 5 Erm [-]3, 5 Kxm [mH]3, 5 Exm [-]

NOMINAL SPECIFICATIONS

Note 1 Measured in infinite baffle.Note 2 Tested in free air (no cabinet).Note 3 Measured using a semi-constant current source, nominal level 2 mA.Note 4 Measured at 25 deg. CNote 5 It is generally a rough simplification to assume that loudspeaker transducer voice coils exhibit the characteristics of an inductor. Instead it

is a far more accurate approach to use the more advanced model often referred to as the “Wright empirical model”, also used in LEAP-4 as the TSL model (www.linearx.com), involving parameters Krm, Erm, Kxm, and Exm. This more accurate transducer model is described in a technical paper here at our web site.

Note 6 After burn-in specifications are measured 12 hours after exiting the transducer by a 20 Hz sine wave for 2 hours at level 14.1 VRMS.. The unit is not burned in before shipping.

Specifications are subject to change without any further notice. Copyright © 2009 - 2012 by Wavecor Ltd., Guangzhou, China. All rights reserved.Wavecor® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com

SPECIFICATIONS

Page 2

SW178WA01 7” alu-cone subwoofer, 8 ohm

PACKAGING AND ORDERING INFORMATIONPart no. SW178WA01-01 Individual packaging (one piece per box)Part no. SW178WA01-02 Bulk packaging

OUTLINE DRAWING(nominal dimensions, mm)

Measuring conditions, SPLDriver mounting: Flush in infinite baffle, back side open (no cabinet)Microphone distance: 1.0 mInput signal: 2.83 VRMS stepped sine waveSmoothing: 1/6 oct.

Measuring conditions, impedanceDriver mounting: Free air, no baffle, back side open (no cabinet)Input signal: Stepped sine wave, semi- current-drive, nominal current 2 mASmoothing: None

CONNECTIONS

Thickness, both terminals: 0.5 mmTerminal plating: Gold

Red mark for positive terminal

4.8 2.8

6.5

7.1

dBSPL

50

55

60

65

70

75

80

85

90

95

100SPL & impedance response, SW178WA01

Frequency, Hz

Ohm

20k10k5k2k1k50020010050202

5

10

20

50

100

200

300

168

4x

5

EVA gasket attached to rear side of chassis

100

178

max

73

max 142

0.5

110

3

Latest update: July 5, 2012


Recommended