Date post: | 10-Jul-2015 |
Category: |
Technology |
Upload: | sytech-corporation |
View: | 140 times |
Download: | 1 times |
Interconnect Documentation for use with TELEX Products
Designed and Manufactured by:Systems Engineering Technologies Corporation
6121 Lincolnia RoadAlexandria, Virginia 22312
TEL. 703-941-7887www.SyTechCorp.com
External connections available via DB-15(F)
Pin 1: Output, RS-232, CDPin 2: Output, RS-232, TXDPin 3: Input, RS-232, RXDPin 4: Input, RS-232, DTRPin 5: GroundPin 6: NCPin 7: Output, 128mVrms, Audio (balanced)Pin 8: Input, 43.5mVrms, Audio (balanced)Pin 9: Output, RS-232, DSRPin 10: Input, RS-232, RTSPin 11: Output, RS-232, CTSPin 12: Output, RS-232, RIPin 13: GroundPin 14: Output, 128mVrms, Audio (balanced)Pin 15: Input, 43.5mVrms, Audio (balanced)
RF ConnectorType: TNC(F)Impedance: 50 Ohms iDEN Module Function Switch
Enabled (To the Left)
Disabled (To the Right)
Status Indicators3VDC 4VDCRXD TXDRed Status Green Status Status Indicators
3VDC LED: Steady Green 3VDC OK4VDC LED: Steady Green 4VDC OKRXD LED: Flickering Yellow Data from HostTXD LED: Flickering Yellow Data to HostRed Status LED: See BelowGreen Status LED: See Below
Alternating Red and Green – FlashstrapFatal Error was detected during power-up.
Flashing Red – Registering, the device is registering with the carrier’s network. Pleas wait.
Steady Red – No Service.
Flashing Red and Green (together) – Unit registered, No packet data service. (no phone service).
Flashing Green – In Full service (phone, DC, GC)
Steady Green – In Use.
iSPACE Card Settings - Standard
TELEX IP-223Remote Adapter
Configuration Screen Shots and Jumper Settings
TELEX IP-233 required the iSPACE RALP VersionSyTech Part Number P/N: RIOS-iDEN-R
Note: After making changes power reset this device
Screen Shot Copyrights to Telex Communications 2008
Serial Connection Radio 1
Radio 2
C-SOFT Dispatch Console
iDOCK 8-Channel ChassisP/N: RIOS-iDEN-8CH
iSPACE iDEN Cards (8)with 2 cards in use
iSPACE TELEX IP 223 – Common Application
800 MHz Antenna
Cable Connections
Interfacing Telex IP-223 to SyTech iSPACE iDEN Card without using the Telex NI-223 Nextel interface unit.
Single iSPACE connected to Telex IP-223 Radio 1 connector
123456789101112131415
CDRxDTxDDTRGND
RXALTXAL
DSRRTSCTS
RIGND
RXAHTXAH
iSPACEDB-15(M)
13141516171819202122232425
12
TXAL (GND)
RXAHTXAH
TELEXRADIO 1DB-25(M)
123456789
RX L1 TTLTX L1 RS232RX L1 RS232TX L2 TTLNCRX L2 TTLRX L2 RS232TX L2 RS232TX L1 TTL
TELEXSerial
DB-9(M)
NOTE: USE QUALITY SHIELDED CABLE FOR AUDIO LINES
P/N: RIOS-CAB-iDEN-S
123456789101112131415
CDRxDTxDDTRGND
RXALTXAL
DSRRTSCTS
RIGND
RXAHTXAH
iSPACEDB-15(M)
13141516171819202122232425
12
TXAL (GND)
RXAHTXAH
TELEXRADIO 2DB-25(M)
123456789
RX L1 TTLTX L1 RS232RX L1 RS232TX L2 TTLNCRX L2 TTLRX L2 RS232TX L2 RS232TX L1 TTL
TELEXSerial
DB-9(M)
Cable Connections
Interfacing Telex IP-223 to SyTech iSPACE iDEN Card without using the Telex NI-223 Nextel interface unit.
Single iSPACE connected to Telex IP-223 Radio 2 connector
NOTE: USE QUALITY SHIELDED CABLE FOR AUDIO LINES
P/N: RIOS-CAB-iDEN-S
Dual iSPACE connected to Telex IP-223 Radio 1 and 2 Connector
123456789101112131415
CDRxDTxDDTRGND
RXALTXAL
DSRRTSCTS
RIGND
RXAHTXAH
iSPACE 1DB-15(M)
13141516171819202122232425
12
TXAL (GND)
RXAHTXAH
TELEXRADIO 1DB-25(M)
123456789
RX L1 TTLTX L1 RS232RX L1 RS232TX L2 TTLNCRX L2 TTLRX L2 RS232TX L2 RS232TX L1 TTL
13141516171819202122232425
12
TXAL (GND)
RXAHTXAH
TELEXRADIO 2DB-25(M)
123456789101112131415
CDRxDTxDDTRGND
RXALTXAL
DSRRTSCTS
RIGND
RXAHTXAH
iSPACE 2DB-15(M)
NOTE: USE QUALITY SHIELDED CABLE FOR AUDIO LINES
P/N: RIOS-CAB-iDEN-R
TELEX Screen Shots for use with iSPACE
RS232AJ26J35Serial Data
+12 VoltsBJ30J8Digital Pull up
HighBJ27J13TX Output Level
600 OhmsBJ10, J15J17, J22
TX Output Impedance
Single EndedA
J25, J28, J29J3, J9, J11TX Output Type
600 OhmsAJ24J14
RX Input Impedance
Single EndedAJ19, J20J16, J21RX Input Type
4 WireBJ5, J6J33, J342 or 4 Wire
POSITIONLINE2LINE 1SIGNALJUMPER
TELEX IP223 Jumper Setting for use with iSPACE
TELEX IP-2002Dispatch Console
Configuration Screen shots
Note: After making changes power reset this device
Testing and configuration of the TELEX IP-223 functioning with the SyTech iSPACE as depicted with the below configuration. This
configuration set both IP-223 port to work as iDEN devices. Other configurations can easily be extrapolated.
Local Network
SyTech2 ea. iSPACE-R Cards
TELEXIP-2002 Firmware Ver. 4.1
TELEXIP-223 Firmware Ver. 4.1PCB 750743
P/N: RIOS-iDEN-2CH
TELEX IP223 and IP2002 with iSPACE Network
Continued on Next Page
Line One Continued
Continued on Next Page
Line Two Continued