SYLLABUS & GENERAL GUIDELINES OF THE

RECRUITMENT EXAMINATION FOR STAFF IN RIICO

1. For each post recruitment examination will be conducted as per schedule declared.

2. The recruitment examination will consist of one MCQ of 200 questions comprising of

two parts. ( Part-I: One and Half hours and Part II: One and Half hours)

Part-I will contain questions from Section A: Reasoning Aptitude (30 questions),

Section B: Quantitative Aptitude (30 questions) and Section C: Language

Comprehension (40 questions) which will include problems of sentence errors,

synonyms, antonyms and passage questions

Part-II: Subject specific(100 questions)

3. There will be a minimum pass mark of 40% for each section.

4. There will be no negative marking.

5. Each question will carry 1 marks each. Total marks will be 200.

6. Questions will be set only in English for post 1 to 4 where as papers will be set both in

Hindi and English for post 5 to 8. However, question paper for General Hindi will be set

only in Hindi and that for English language will be set in English only.

Syllabus for the subject specific Part

Post-1 Dy. Manager (HRD/GAD/ Infra)

100 questions from the syllabus of MBA specialization paper ( HR ) with following thrust areas:

Managerial Communication

Organizational behavior

Group Dynamic

Managing Interpersonal Effectiveness

Organization Development

Performance Management & Retention Strategies

Industrial Relation & labor laws

Post-2 Dy. Manager (ID/Tech)

The subject specific part will consist 50 questions from the Engineering and 50 questions from

Mananagment subjects

Engineering subject

50 questions will be put from the syllabus of following papers taught in the first year of

Engineering degree courses

1.Engineering Mathematics

2. Electrical and Electronic Engineering

3. Mechanical Engineering

4. Engineering Chemistry and Physics

5. Fundamentals of computer

ENGINEERING MATHEMATICS-I

Unit Contents

Unit-I

Solid Coordinate Geometry

Cartesian coordinates in shapes, Direction Cosines.

Different form of equations of a plan, Angle between two planes, Perpendicular distance of point from a plan, Equation to plane dissecting the angle between two planes, Volume of a tetrahedron.

Equation of a straight line, Intersection of a plane and a straight line in space. Shortest distance between two non-intersecting straight lines.

Equation of sphere, Intersection of sphere and a plane, Tangent plane and normal lines.

Unit-II

Solid Coordinate Geometry & Matrices

Equation of a right circular cone and a right circular cylinder.

Rank of matrix, Inverse of matrix.

Solution of simultaneous linear equation by matrix method.

Eigen values & Eigen vectors, Cayley-Hamilton theorem.

Unit-III Differential Calculus

Asymptotes (Cartesian coordinates only), Curvature.

Concavity, Convexity, Points of inflexion (Cartesian coordinates only)

Simple curve tracing: Cartesian and Poler curves including Cardioids, Lemniscates of Bernoulli, Limacon, equiangular Spiral, Folium of Descartes.

Unit-IV Differential Calculus

Partial differentiation, Euler’s theorem on homogeneous functions.

Approximate Calculation.

Maxima & Minima of functions of one & two variables connected by a relation. Integral Calculus

Application of integral Calculus in finding lenths, areas of simple plane curves.

Unit-V Integral Calculus

Application of integral calculus in finding volumes & surface of solids of revolution.

Double Integrals, Areas and volumes by double integration.

Change of order of integration.

Unit –V Integral Calculus

Application of integral calculus in finding volumes & surface of solids of revolution.

Double integrals, Areas and volumes by double integration.

Change of order of integration.

ENGINEERING MATHEMATICS-II

Unit Contents

I Vector Calculus

Vector & scalar Point functions.

Differentiation & integration of Vector Functions.

Gradient, Divergence, Curl

Line Integrals

II Liner Programming

Introduction to Liner Programming Problems, Mathematical Formulation.

Graphical Method to solve a Liner Programming Problem with tow variables.

Convex Sets and their properties, Theorems on Liner Programming (without proof)

Simplex Algorithm and its Applications to Simple Problems (excluding the cases of degeneracy)

III Dynamics

Angular motion, Radial Velocities and Accelerations.

Tangential and normal accelerations.

Rectilinear motion-Simple Harmonic Motion under inverse square law

IV Dynamics

Rectilinear motion in a resisting medium.

Circular motion, Banking of trucks.

V Differential Equation

Differential equation of first order and fist degree.

Linear differential equation of higher order with constant coefficients

Electrical & Electronics Engineering

Unit Contents

I DC Networks

Kirchoff’s Law, Node Voltage & Mesh Current Method.

Delta-star and star-delta Transformation, Source Conversion

Classification of network Elements, Superposition Principle , Thevenin’s Theorem

II Single Phase AC Circuits

Single Phase EMF Generation, Average and Effective Values.

Solution of R, L, C Series, Parallel and Series-Parallel Circuits.

Complex Representation of Impendence, Phase Diagram.

Power and power Factor. Three Phase Ac Circuits

Three Phase EMF Generation, Delta and Star Connection.

Line and Phase Quantities

Solution of three Phase Balanced Circuits.

Phasor Diagram

Measurement of power in Three Phase Balanced Circuits.

III Transformer

Faraday’s Law of Electromagnetic, Induction.

Construction and Principle Operation of Single Phase Transformer, EMF Equation

Voltage and Current Relationship and Phasor Diagram of Ideal Transformer

IV Electrical Measuring Instrument

Introduction, Types of measuring Instruments.

Deflecting, Controlling and Damping torque, DC PMMC Instruments.

Shunts and Multipliers, Moving Iron Ammeter and Voltmeter, Dynamometer,

Wattmeter, Induction type energy meter.

V Diode Circuits

Theory of PN Junction, PN Junction Diode, Zener Diode, volt-Ampere Characteristics, Diode Resistance, Breakdown Phenomenon

Principle of Operation and Circuits of Half Wave and Bridge Rectifier, Ripple Factor and Ripple Efficiency, Introduction to Filters

Transistors

Working principle and Operation of Bipolar Junction Transistor, Transistor Current.

Components, Characteristics and Basic Principle of Operation of CE, CB and CC Transistor Amplifiers.

Introduction to Amplification, Modulation, Demodulation and Oscillation

MECHANICAL ENGINEERING

Unit Contents

I Basic Concepts

Thermodynamic systems, Properties, Work and Heat Working Fluids

Air and Steam, Calculation of properties air as ideal gas for various thermodynamic processes.

Use of stem tables and Molier charts for steams properties. First and Second Law or Thermodynamics

Non-flow and flow energy equations: Second law statements;

II Internal Combustion Engines

Otto and Diesel cycles: Thermal efficiency calculations, Classification.

Tow and four stroke engines, construction and working of petrol and diesel engines.

Introduction to various systems of IC engines. Gas Turbine Plant

Ideal Brayton Cycle: Thermal efficiency calculation.

Construction and working of reciprocating and rotary air compressors.

Applications of gas turbines plants.

III Steam Power Plant

Simple Rankine Cycle : Thermal efficiency calculation.

Classifications of steam generators , Construction and working of low and high-pressure boilers.

Introduction to various components of thermal power plants. Refrigeration and Air Conditioning

Psychometric: Use of Psychometric charts, Elementary concept of refrigeration and air conditioning.

Vapour compression cycle, Working principle and schematic diagrams of refrigerators, Air conditioners and plants.

IV Manufacturing Processes

Classification, Principle of working, Specification.

Application of various machine tools, lathe, drilling, shaper, and milling machines.

Basic descriptions and application of hot and cold working processes, forging, bending, shearing, drawing and forming operations.

V Foundry

Tools, equipments and moulding materials. Gas Welding

Arc welding, Soldering and brazing. Power Transmission

Classification and application of mechanical drives like belts ropes.

Chains and gear drives (excluding epicyclic trains) and their velocity ratios.

Ratio of tensions in belts and ropes.

ENGINEERING CHEMISTRY

Unit Contents

I Water

Common impurities, Hardness, Determination of hardness by Clark’s test and

Complexmetric (EDTE) method , Degree of hardness Municipal Water Supply

Requisites of drinking water , Purification of water, Sedimentation, Filtration, Sterilization, Break Point Chlorination

Water for Steam Making

Boiler troubles carry over, Corrosion, Sludge and scale formation and Caustic embrittlement.

Methods of Boiler Water Treatment

Preliminary treatment s, Preheating, Lime-soda Process, Permutit or Zeolite Process.

Deionizer or demineralizers, Feed water conditioning , Internal treatment, blow down, Problems based on water treatment (Lime-Soda process)

II Fuels

Chemical fuels: Origin and classification of fuels.

Solid fuels: Coal, Proximate and ultimate analysis of coal , Significance of the constituents . Gross and net calorific value, Determination of calorific values by Bomb Calorimeter , Coke-metallurgical coke-carbonization process

Manufacture of coke-beehive, Coke ovens and By-product , Coke ovens

Liquid Fuels: Advantages, Petroleum and refining of petroleum , Synthetic Petrol , Refining and reforming of gasoline, Knocking, Octane Number, Knocking –antiknocking Agents, Cracking.

Gaseous Fuels: Advantages, Manufacture, Compositions and calorific value of coal gas, and oil-gas, Determination of calorific values by Junker’s calorimeter, Flue gas analysis by Orsat apparatus

III Phase Rule

Statement , Definition and meaning of the terms involved, Application to one component system, Water and sulphur systems , Study of two component system: Ag-Pb system

Polymers

Plastics: Classification and constituents of plastic and their uses. Preparation, Properties and uses Polyethylene, Bakelite, Terylene, and Nylon.

Rubber: Natural rubber, Vulcanization, Synthetic rubbers viz. Buna-S. Buna-N, Bufyl and Neoprene rubbers.

Lubricants

Classification ,Types of Lubricants, Properties and uses, Viscosity & viscosity index ,Flash & fier point , Cloud and pour point, Emulsification.

IV

Corrosion

Definition and its significance , Theories of corrosion, Galvanic Cell and concentration cell, Pitting and Stress Corrosion , Protection against Corrosion, Protective Metallic coating

Pollution

Elementary ideas of Air and Water pollution, effect of air pollution, Depletion of ozone layer and its Environmental impact, Substitute of Chlorofluorocarbons.

Explosives

Introduction, Classification, Requisites of explosives, Preparation of Explosives, Plastic explosives, Blasting fuses, Application of explosives.

V Cement

Manufacturing. Of Portland Cement ,Vertical shaft kiln Technology, Chemistry of setting and Hardening.

Refractories

Definition, Properties, Classification, Properties of silica and fireclay refractries. Glass

Preparation, Varieties and uses. New Engineering Materials

Brief ideas of following : Superconductors, Organic Electronic materials, Fullerenes.

PHYSICS

Units Contents

I Interference

Theory and method of measurement of wavelength using Fresnel’s Biprism.

Newton’s rings and Michelson Interferometer

Measurement of thickness of thin sheet using Biprism. Polarisation

Idea of behaviour of the electric vector of an EM wave leading to plane.

Circularly and elliptically polarized light.

Production and detection of circularly and elliptically polarized light.

Measurement of specific rotation using Half shade and Biquartz Devices.

II Diffraction

Fraunhofer’s diffraction at a single slit.

Theory and method of measurement of wavelength by plane diffraction grating

Diffraction of X-ray and matter waves from crystals, Bragg’s law

Concept of resolving power. Rayleigh criteria

Resolving power of diffraction grating

III Laser & Optical Fibers

Spatial & Temporal coherence.

Laser as coherent light criteria of laser action, Ruby and HE-Ne lasers.

Application of lasers with special emphasis an Holography.

Elementary ideas of optical fibers , Numerical aperture of a fiber.

IV Special Theory of relativity & Nuclear Instruments

Michelson-Morley experiment. Postulates of special theory of relativity.

Lorentz Transformation.

Relativity of length, mass, time and velocity. Mass –Energy relation.

Construction, theory and application of Geiger-Muller counter, Proportional & Scintillation counters.

V Wave Mechanics

Photoelectric effect and Compton Effect as evidences of quantum nature of radiation.

Heisenberg’s uncertainly principle, Schrodinger’s equation for a free particle.

Potential barrer and tunnel effect. Particle in one and three dimensional box.

Degeneracy, free-electron model of asolid.

Density of energy states & Fermi energy.

FUNDAMENTALS OF COMPUTER

Unit Contents

I Introduction

Types of computers and generations, Basic architecture of computer and its building blocks, Inputs-output Devices, Memories.

II Number systems

Binary, Octal, Decimal and Hexadecimal Representation of numbers.

Integers and floating point numbers.

Representation of Characters: ASCII and EBCDIC codes.

III Classification of Computer Languages

Machine Assembly and high level languages.

Brief idea of operating system, assembler, Compiler and interpreter. Programming in C

Need of Programming Languages, Defining problems, Flowcharts and algorithm development.

IV Data

Data types, constants, variables, operators, and expressions.

Input and Output Statements, Conditional and control statements, Arrays.

V Structures and Unions, Pointers and File Handling

Management subject

50 questions from the syllabus of following areas covered in MBA course:

General management

Management Information systems.

Managerial Economics.

Marketing,

Accounting & Finance.

Human Resources Management.

Organizational Behavior.

Strategic Management.

Operation Management,

Telecom Knowledge, and

Current events of national and international importance

Post-3 Assistant Site Engineer (Civil)

100 questions from the following

1. BUILDING MATERIALS

Timber: Different types and species of structural timber, density-moisture relationship, strength

in different directions, defects, influence of defects on permissible stress, preservation, dry and

wet rots, codal provisions for design, plywood. Bricks: Types, Indian Standard classification,

absorption, saturation factor, strength in masonry, influence of morter strength on masonry

strength. Cement: Compounds of, different types, setting times, strength. Cement Mortar:

Ingredients, proportions, water demand, mortars for plastering and masonry. Concrete :

Importance of W/C Ratio, Strength, ingredients including admixtures, worksability, testing

for strength, elasticity, non-destructive testing, mix design methods.

2. SOLID MECHANICS

Elastic constants, stress, plane stress, Mohr’s circle of stress, strains, plane strain, Mohr’s circle

of strain, combined stress; Elastic theories of failure; Simple bending, shear; Torsion of circular

and rectangular sections and simple members.

3. STRUCTURAL ANALYSIS

Analysis of determinate structures - different methods including graphical methods. Analysis of

indeterminate skeletal frames - moment distribution, slopedeflection, stiffness and force

methods, energy methods, Muller-Breslau principle and application. Plastic analysis of

indeterminate beams and simple frames - shape factors.

4. DESIGN OF STEEL STRUCTURES

Principles of working stress method. Design of connections, simple members, Built-up sections

and frames, Design of Industrial roofs. Principles of ultimate load design. Design of simple

members and frames.

5. DESIGN OF CONCRETE AND MASONRY STRUCTURES

Limit state design for bending, shear, axial compression and combined forces. Codal provisions

for slabs, beams, walls and footings. Working stress method of design of R.C.

members. Principles of prestressed concrete design, materials, methods of prestressing, losses.

Design of simple members and determinate structures. Introductions to prestressing of

indeterminate structures. Design of brick masonry as per I.S. Codes.

6. CONSTRUCTION PRACTICE, PLANNING AND MANAGEMENT

Concreting Equipment: Weight Batcher, Mixer, vibrator, batching plant, concrete pump. Cranes,

hoists, lifting equipment. Earthwork Equipment : Power shovel, hoe, dozer, dumper, trailers and

tractor, rollers, sheep foot rollers, pumps. Construction, Planning and Management : Bar chart,

linked bar chart, work-break down structures, Activity - on - arrow diagrams. Critical path,

probabilistic activity durations; Event-based networks. PERT network: Time-cost study,

crashing; Resource allocation.

7. (a) FLUID MECHANICS, OPEN CHANNEL FLOW, PIPE FLOW Fluid Properties, Pressure, Thrust, Buoyancy; Flow Kinematics; Integration of flow

equations; Flow measurement; Relative motion; Moment of momentum; Viscosity, Boundary

layer and Control, Drag, Lift; dimensional Analysis, Modelling; Cavitation; Flow oscillations;

Momentum and Energy principles in Open channel flow, Flow controls, Hydraulic jump, Flow

sections and properties; Normal flow, Gradually varied flow; Surges; Flow development and

losses in pipe flows, Measurements; Siphons; Surges and Water hammer; Delivery of Power

Pipe networks.

(b) HYDRAULIC MACHINES AND HYDROPOWER

Centrifugal pumps, types, performance parameters, scaling, pumps in parallel; Reciprocating

pumps, air vessels, performance parameters; Hydraulic ram; Hydraulic turbines, types,

performance parameters, controls, choice; Power house, classification and layout, storage,

pondage, control of supply.

8. (a) HYDROLOGY

Hydrological cycle, precipitation and related data analyses, PMP, unit and synthetic

hydrographs; Evaporation and transpiration; Floods and their management, PMF; Streams and

their gauging; River morphology; Routing of floods; Capacity of Reservoirs.

(b) WATER RESOURCES ENGINEERING

Water resources of the globe: Multipurpose uses of Water: Soil-PlantWater relationships,

irrigation systems, water demand assessment; Storages and their yields, ground water yield and

well hydraulics; Waterlogging, drainage design; Irrigation revenue; Design of rigid boundary

canals, Lacey’s and Tractive force concepts in canal design, lining of canals; Sediment transport

in canals; Non-Overflow and overflow sections of gravity dams and their design,

Energy dissipators and tailwater rating; Design of headworks, distribution works, falls, cross-

drainage works, outlets; River training.

9. ENVIRONMENTAL ENGINEERING

(a) WATER SUPPLY ENGINEERING Sources of supply, yields, design of intakes and conductors; Estimation of demand; Water

quality standards; Control of Water-borne diseases; Primary and secondary treatment, detailing

and maintenance of treatment units; Conveyance of treatment units; Conveyance and distribution

systems of treated water, leakages and control; Rural water supply; Institutional and industrial

water supply.

(b) WASTE WATER ENGINEERING

Urban rain water disposal; Systems of sewage collection and disposal; Design of sewers and

sewerage systems; pumping; Characteristics of sewage and its treatment, Disposal of products of

sewage treatment, streamflow rejuvenation Institutional and industrial sewage management;

Plumbing Systems; Rural and semi-urban sanitation.

(c) SOLID WASTE MANAGEMENT

Source, classification collection and disposal; Design and Management of landfills.

(d) AIR AND NOISE POLLUTION AND ECOLOGY

Sources and effects of air pollution, monitoring of air pollution; Noise pollution and standards;

Ecological chain and balance, Environmental assessment.

10. (a) SOIL MECHANICS

Properties of soil, classification and interrelationship; Compaction behavior, methods of

compaction and their choice; Permeability and seepage, flow nets, Inverted

filters; Compressibility and consolidation; Shearing resistance, stresses and failure; soil testing in

laboratory and insitu; Stress path and applications; Earth pressure theories, stress distribution in

soil; soil exploration, samplers, load tests, penetration tests.

(b) FOUNDATION ENGINEERING

Types of foundations, Selection criteria, bearing capacity, settlement, laboratory and field tests;

Types of piles and their design and layout, Foundations on expansive soils, swelling and its

prevention, foundation on swelling soils.

11 SURVEYING

Classification of surveys, scales, accuracy; Measurement of distances - direct and indirect

methods; optical and electronic devices; Measurement of directions, prismatic compass, local

attraction; Theodolites - types;

Measurement of elevations - Spirit and trigonometric levelling; Relief representation; Contours;

Digital elevation modelling concept; Establishment of control by triangulations and traversing -

measurements and adjustment of observations, computation of coordinates; Field astronomy,

Concept of global positioning system; Map preparation by plane tabling and by photogrammetry;

Remote sensing concepts,

map substitutes.

12. TRANSPORTATION ENGINEERING

Planning of highway systems, alignment and geometric design, horizontal and vertical curves,

grade separation; Materials and construction methods for different surfaces and maintenance:

Principles of pavement design; Drainage. Traffic surveys, Intersections, signalling: Mass transit

systems, accessibility, networking. Tunnelling, alignment, methods of construction, disposal of

muck, drainage, lighting and ventilation, traffic control, emergency management. Planning of

railway systems, terminology and designs, relating to gauge, track, controls, transits, rolling

8tock, tractive power and track modernization; Maintenance; Appurtenant works;

Containerisation. Harbours - layouts, shipping lanes, anchoring, location identification; Littoral

transport with erosion and deposition; sounding methods; Dry and Wet docks, components and

operational Tidal data and analyses. Airports - layout and orientation; Runway and taxiway

design and drainage management; Zoning laws; Visual aids and air traffic control; Helipads,

hangers, service equipment.

Post 4: Assistant Account Officer ( Grade II )

100 questions from the syllabus of B.Com by D.C.W.A./M.Com (ABST) with following thrust areas:

Accounting standards (1 to 20)

Bank reconciliation & banking transactions

Cost Estimate Ascertainment & Appropriation of Overheads

Valuation of inventories

Companies act: basic provisions about final accounts, audit

Financial statements, including revised schedule VI

Elementary knowledge of service tax

Financial management

Income tax

POST No. 7: Draughtsman Cum Tracer (Civil)

100 questions will be set as from the following topics

Drawing office organisation. Drawing instruments, equipments materials their use, care &

maintenance, safety precautions. Introduction to IS code of practice and architectural drawings.

Importance of lettering, writing of letters and figures sizes, proportion, etc. as per IS code.

Geometrical drawing-definition, construction of plain geometrical figures.

Method of construction of spiral and helix.

Principles, representation and construction of different types of scales, graphic scales,

recommended scales for drawing with reference to IS codes. Choice of scales.

Types of lines and different conventional representation as per IS.

Definition and types of projections.

Methods of projection as per IS.

Projection of points, lines, planes and solids.

Sections of solid and their true shapes

Principle of Isometric & Axonometric projection, difference between Isometric drawing &

Isometric projection,

Isometric scale, dimensioning an Isometric drawing.

Reducing and enlargement technique by graphically and by instrument.

Perspective projection – definition of picture plane, station point, horizontal line, vanishing

point, cone of vision, central visual ray, spectator, eye level focus, fundamentals - diminution,

foreshortening, convergence.

Method of drawing of two point perspective. Comparative study of perspective by changing the

position of spectator, vanishing point. Distortion, limits of exactness, limitation of field of vision.

Building materials:

Clay products like Bricks, tiles, terracotta, earthenware; stoneware, stone, cement, lime, surki,

sand, timber, glass, paints, texture etc.

Sequence of construction of a building. Names of different parts of building. Bricks masonry –

principles of construction of bonds .Tools and equipment used. Scaffolding.

Stone masonry, terms used, principles of construction, classification, composite masonry and

strength of walls. Timber: Structure Indian timber uses

Foundation:-purpose, causes of failure of foundation, bearing capacity of soils, dead load, live

load, wind load and seismic load. Examination of ground. Types of foundation .Drawing of

footing foundation, setting out of building on ground excavation, shoring & simple machine

foundations.

Damp proof course,

Sources and effects of dampness,

method of prevention of dampness in building, periodic repair and care for prevention.

Anti-termite treatment.

Surveying – their classifications, plane survey, geodetic survey, purpose of survey – instruments

used in survey. Nature of surveyors work – importance of system. Common terms and

definitions used in surveying conventional signs used in

Field book and survey maps. Linear measuring instrument used by surveyors, their descriptions

and uses. Types of chain and chain survey, compass survey, plane table survey and levelling.

Field book types- methods of entry of check lines – its importance.

Locations of details – types of off-sets and their limit- town survey traversing with chain

procedure in plotting chain lines skeleton, its check and filling in details.

Technical terms used in compass survey , difference between angles and bearings-magnetic and

true meridians declination and its variation , local attraction , its detection , and elimination.

Plane table survey advantage & disadvantages of plane table surveying general instruction for

Plate Table survey Methods of Plate tabling –Radiation –Intersection Traversing Resection.

Two point and three point problems triangle of error and its elimination – Lehman’s rule –

mechanical and graphical method.

Instruments employed, use, care & maintenance. Field problems. Field book plotting.

Introduction to plane table in surveying. Instruments employed, use, care&maintenance.

prismatic compass.

Instruments and accessories-their uses and description level book. Differential; levelling

application of chain and levelling to building construction. Plotting, preparation of contour

computing earth work by spot level and contours. Setting out work.

Road: Introduction to roads, general principles of alignment.

Classification and construction of different types of roads.

Indian railways –their gauges, construction of permanent ways. Different rail sections. Use of

stone ballast in railway track. Use and types of sleepers.

Bridge:-introduction to bridge, component parts of bridge. classification of culverts(IRC)

Bridges-types, location of a bridge, tunnels.

INTRODUCTON OF WATER RESOURCES ENGINEERING.

Different terms used in irrigation.

Hydrology like duty, delta, base period, intensity of irrigation, hydrograph , peak flow, run off,

catchment area, CCA, corps like, rabi, kharif etc.

Storage/ diversion head work definition: types of dam –masonry, concrete, arc and buttress

dams, earth.

(A)Reservoir –types of reservoirs viz . Single purpose and multipurpose, area, capacity of

reservoir.

B) CANALS:-canals, classification of canals and distribution system, canal structures via head

regulators, escape, etc. Drawing of canal alignment including longitudinal and cross section of

canals with the given data. Types of cross drainage works viz. aqueducts, siphon aqueduct, super

passage, level crossing in irrigation.

Introduction –terms used in public health engineering. System of sanitation house plumbing,

sanitary fittings etc. types of supply system and purification of water.

Introduction to RCC uses materials proportions and form work, including bending of bars and

construction reference to IS code. Reinforced brickwork.

Material used for RCC, methods of concreting, construction selection of materials course

aggregate cement –water, reinforcement, characteristics. Methods of mixing concrete- hand and

machine, slump test, water cement ratio.

Flooring:

Different types of floors, materials used in floor and construction process.

Forms of riveted head, types of riveted joints and connection, failure of riveted joints.

Introduction to structural drafting. Arrangements of drawing, standard drawing.

Types of mortar & concrete proportion and mixing. Plastering and pointing. White washing

&distempering.

Types of ground floor and methods of constructing granolithic, mosaic brick tiles etc. floors.

Arches &lintel-technical terms ,forms of brick and stone ,form work and centering . Market

forms and sizes.

Carpentry joints terms, classification of joints.

Door: parts of door , location, sizes, and types

Windows and ventilators: including steel windows and ventilators fixtures and fastening used in

doors. Windows and ventilators.

Roof: pitched roof types, roof covering, and component parts of roof. Theory of trussing, king

and queen post trusses

Classification and construction of upper floors including water-proofing, general principles of

construction of masonry & R.C.C.

STAIRS: Terms, forms materials, planning and designing of stairs. Details of construction

Safety precaution &elementary first aid, forge and fuel. Lighting fire. Common hand tools – their

descriptions and use. Description of plumbing operations.

Safety precautions & elementary first aid.

Carpenters’ hand tools, their names description and uses. Common joints Use of nails, screws ,

hinges, dowels etc. Preparation of glue & putty. Grinding & sharpening of tools .Their care &

maintenance. Use of different types of joints properties and uses of different timbers used in

construction work.

Safety precautions and elementary first aid. Artificial respiration and treatment of electrical

shock. Elementary electricity. General idea of supply system. Wireman’ tool kits. Wiring

materials. Electric fittings. System of wiring. Wiring installation for domestic lighting.

Masonry tools:

Safety precautions, description, uses and their care, Details of different bonding wall and section

according to IS

Introduction to theodolite, temporary adjustment of theodolite – procedure in setting up – method

of measurement of horizontal & vertical angles and height.

Residential building. Principles of planning. Orientation local building bye-laws including IS

code, type of residential building, rooms services, utilities which constitute as dwelling house.

Estimating. Method and find out quantities for a single storied residential building.

Preparing bar bending schedules

Building Estimating.

Types of estimate, standard method of taking out quantity, labour & material detailed & abstract

estimate. Analysis of rates for simple items of work. Schedule of rates, specifications.

Residential building, Planning of building, local bye-laws including IS code. Types of residential

building rooms service utilities which constitute a dwelling house. Building bye-laws of State

urban Development authorities / boards, Improvement trust etc.

1)Window command and their uses and Familiarization with word processing software.

2) CAD commands and use of different menus of CAD -

Use of different co –ordinate system, geometrical drawing and 2 D Drafting, different edit

commands, Concept of 3d Drafting, layout and printing of drawing.

Architectural Desk top and creating modeling

SCHEME AND SYLLABUS OF THE COMPETITIVE EXAMINITION

FOR THE POST STENOGRAPHER (POST NO.6)

Scheme of examination: the competitive examination shall include the following papers and each

paper shall carry the number of marks as shown against it, namely:-

Papers DURATION MARKS

Phase- 1

1. General knowledge every day 3 Hour 100

Science and general

Knowledge of Rajasthan

2. General Hindi and English 3 Hour 100

Phase- 2

1. English shorthand ( the test 10 Minutes

Shall consist of dictation 50

100 words per minute)

Transcription and typing 60 Minutes

Of dictated passage in English

On computer

2. Hindi shorthand ( the test shall 10 Minutes

consist of dictation of 80

Words per minute) 50

Transcription and typing of 70 Minutes

Dictated passage in Hindi on

computer

Explanation:

(1) The standard of the paper will be of the secondary examination of the board of secondary

education, Rajasthan. The Syllabus and scope of each paper of the examination will be as

prescribed by the commission from time to time and will be intimated to the candidates

within the stipulated time in the manner as the commission deem fit.

(2) The competitive examination will be held in two phases – phase-1 & phase-II. All the papers

phase-1 will be of objective type.

(3) Candidates securing minimum 40% marks in phases-1 shall only be admitted to the phases -II

subject to three times the number of advertised vacancies but in the said range all those

candidates who secure the same percentage of marks shall be included.

(4) The marks obtained by a candidate in the phase -1 and phases-II of the examination will be

counted in determining their final order of merit.

(5) It will be necessary for candidates to do typing work on the computer and he will bring his

own computer, pen and pencil for the test.

SCHEME AND SYLLABUS OF THE COMPETITIVE EXAMINITION FOR THE POST OF

JUNIOR ASSISTANT (Post No.8)

Scheme of examination: the competitive examination shall include the following

papers and each paper shall carry the number of marks as shown against it namely:-

Papers Durations Marks

Phase-1

1. General knowledge, 3 hours 100

Everyday science and

Mathematics.

2. General Hindi & English. 3 hours 100

Phase -II

(i) For candidates other than

Persons with disabilities:-

(1) Type – writing in Hindi on

Computer

(a) Speed test 10 Minutes 25

(b) Efficiency test 10 Minutes 25

(2) Type- writing in English on Computer

(a) Speed test 10 Minutes 25

(b) Efficiency Test 10 Minutes 25

(ii) Persons with disabilities

Will be given the average marks

Obtained by them in phases-1

Explanation:

1. “Persons with disabilities” mean a person who is eligible for appointment

to the post of lower division clerk under the provisions of the Rajasthan

employment of the person with disabilities rules ,2000

2. With proof of being so disabled, the candidate shall be required to submit

a certificate issued by an officer not below the rank of chief medical and

health officer at the time of submitting his application to the commission

for appearing in the examination.

3. The standard of the papers will be that of the secondary examination of

the board of secondary education Rajasthan. The syllabus and scope of

the each paper of the examination will be as prescribed by the

commission from time to time and will be intimated to the candidates

within the stipulated time in the manner as the commission deem fit

4. The competitive examination will be held in two phases-1 and phases II .

All the papers of phase -1 will be of objective type.

5. Candidates securing minimum 40 % marks in the phase -1 shall only be

admitted to the phase -2 subject to three times the number of advertised

vacancies but in the said range all those candidates who secure the same

percentage of marks shall be included.

6. The marks obtained by a candidate in the phase -1 and phases - II of the

marks of the examination will be counted in determining their final order

of merit.

7. It will be necessary for a candidate to do typing work on the computer

and he will bring his own computer , pen and pencil for the test.”

Scheme of written examination for the Post 5: Junior Legal Officer

The subject specific part will consist two sections. Section 1 will contain 25 questions from the syllabus

of LLB with following thrust areas will be set (25 marks) as MCQ type questions, whereas section 2 will

consist two descriptive type questions to check the subject knowledge as well as drafting knowledge of

the candidate. The descriptive part of the answer will be evaluated independently by two examiners

and average of the two will be awarded and no re-evaluation facility will be made.

The civil procedure code

Transfer of property act

The contract act

The land acquisition act

The companies act

The land revenue act & industrial area allotment rules

The single window enabling act

The DRT act

The constitution of India ( article, 226-227, 32, 14, 27, 22)

The labor law (I.D. act, minimum wages act, standing order act, bounded labour abolition act,

P.F act , E.S.I. act)

The SICA act

Right to information act

Water/air pollution act

The tenancy act

The Indian penal code

The Indian recovery act

The criminal procedure code

The PDR act

The pleading & conveyance act

Right to hearing act

Rajasthan industrial area development authority act

General Instructions

1. The scope of the syllabus of MBA will be that of Rajasthan Technical University, Kota

and that for LLB and M.Com (ABST) will be that University of Rajasthan, Jaipur.

2. Questions will be set only in English to post 1 to 4 whereas that for post 5 to 8 will be

set both in English and Hindi. Question papers for General Hindi and English language

test will be set only the respective language .

3. No mobile phones or any type of electronic gadgets will be allowed in the examination

hall. All the candidates will be frisked at the entrance gate. Only the admit card ,one

photoid and two normal pen, will be allowed inside the examination hall.

4. Candidates will be required to make their own arrangements to keep their belongings

and mobile phones since the examination centres will not have the facilities to keep these

items.

5. No candidate will be allowed to enter examination hall after 10 minutes commencement

of examination and shall not be allowed to go out before completion of examination.

6. Candidates will be required to bring their admit card with a passport size Colour

Photograph fixed on it and handover the same to the Invigilator after signing on it and

putting their left hand thumb impression failing which candidate will be declared not

eligible on account of not submitting hardcopy of their admit card.

7. Candidates will be required to bring their Photoid in the examination hall.

8. All applicants are advised to visit this site regularly for further information.

Co-ordinator