Syllbus M.tech ME

5/28/2018 Syllbus M.tech ME

1/37

GURU KASHI UNIVERSITY

GURU GOBIND SINGH COLLEGE OF ENGINEERING &TECHNOLOGY

M.Tech. (Mechanical Engineering)

MATERIALS TECHNOLOGY (142101)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:

Introduction to material science & engineering, Classification of engineering materials,Properties of materials, Crystal geometry and structure determination.

2. Mechanical Properties & Testing of Materials:Fundamental mechanical properties, creep, fatigue and fracture processes, Factors effecting

mechanical properties, destructive and non-destructive testing of materials.

PartB

3. Metals and Alloys:

Ferrous and non-ferrous metals, alloy system, solid solutions, Phase diagram, phasetransformation, iron-carbon system, isothermal transformationTTT diagram, Heat treatment

of plain carbons steels, low alloy steels stainless steel, aluminum alloys, copper alloys and.

4. Ceramic Materials:Introduction, Simple ceramic crystal structure, silicate structure, mechanical properties of

ceramics.

PartC

5. Polymer Materials:Polymer, broad classification, basic concept of polymer science, mechanical properties of

polymers, reinforced polymers, manufacturing processes of polymer.

6. Nano Structural Materials:

Production methods for Carbon Nano Tubes (CNT), Properties of CNT, Advantages of Nano-materials.

PartD

7. Composite Materials:Introduction, Characteristics of particles, reinforced and fibre reinforced composites.

8. Deterioration of Materials:Oxidation and Corrosion, Corrosion control and corrosion resistance of alloys Wear andErosion, effect of porosity and hardness on degradation of materials.

References:

1. Sidney H. Avner, Introduction to Physical Metallurgy, Mc-GrawHill, N. York.2. Donald R. Askeland and Pradeep P. Phule, The science and Engineering of Materials,

Thomson.

3. V. Raghavan, Material Science & Engineering, Prentice-Hall of India (P), N. Delhi4. William F. Smith, Principles of Materials Science and Engineering, Mc-Graw Hill.5. Shirvastav, Non-Destructive Testing Technique.6. A.K. Jena & M.C. Chaturvedi, Phase Transformations in Materials, Prentice Hall


2/37




COMPUTER AIDED DESIGN (142102)

Credit: 04 L T P

4 0 0PartA

1. Introduction:Overview of conventional design & manufacturing process, computers role in design,benefits of computer application, relation of CAD with CAM, history of CAD

development, current trends in CAD.

2. CAD Hardware & Software:Central processing unit, memory, input & output devices, types of computer systems,

computer programming, general information of various software for CAD, types of file

formats & their exchange, graphics standards.

PartB

3.

Geometric Modeling:Curve representation methods, surface representation methods, half spaces, boundary

representation (B-rep), sweep representation, constructive solid geometry (CGS), solidmanipulations, modeling facilities desired.

4. Transformations:Translation, rotation, scaling symmetry, reflection, homogeneous transformations,orthographic projections, axonometric projections, oblique projections, perspective

transformation.

PartC

5. Visual Realization:Basic concepts of visual realization, hidden line removal, hidden surface removal,

shading surfaces and solids visibility techniques, sorting coherence, hidden lineremoval for curved surface.

6. CAD and CAM integration:Introduction, part production cycle, manufacturing system, process, integration

requirements, process planning, tool path generation and verification, Design and Engg.

applications.

PartD

7. Introduction to Reverse Engineering and Rapid Prototyping:8. Introduction to Design and Engineering Applications:

Geometry and mass property formulations.Practice on Drafting and Modeling systems : Basic geometric commands, layers, display

control commands, editing, dimensioning, solid modeling on available CAD packages.

Books Recommended:1. Groover and Zimmer, CAD/CAM, Prentice Hall2. I. Zeid, CAD/CAM: Theory and Practice, McGraw Hill3. M.E. Mortenson Geometric Modeling


3/37




ADVANCE MANUFACTURING PROCESSES (142103)

Credit: 04 L T P

4 0 0

PartA

1.Introduction:Overview of general trends in Manufacturing, concept and significance of important

properties related to manufacturing processes, limitations of conventional manufacturingprocesses need and evolution of advanced manufacturing, selection and economics of

manufacturing processes.

PartB

2.Advanced Machining Processes:Classification, Review of conventional machining processes, Principles, process parameters,

capabilities and mechanism of material removal of AJM, WJM, AWJM, USM3.Electro Chemical Type Advanced Machining Processes:ECM-Process principle, mechanism of material removal, Kinematics and dynamics of ECM,Tooling design, Choice and analysis of process parameters, Surface finish and accuracy.

PartC

4.Thermal Type Advanced Machining Processes:EDM, LBM and EBM processes: Working principle, Power circuits, Mechanism of material

removal, Process parameters and characteristics, Surface finish and accuracy, Shape and

materials applications, limitations.

PartD

5.Derived And Hybrid Advanced Machining Processes:Introduction of processes like rotary ultra sonic machining, electro stream drilling, shapedtube electro machining, wire electro discharge machining, electro chemical grinding, electrochemical honing, electro chemical deburring and electrochemical spark machining.

Recommended Books:1. Shan and Pandey, Modern Machining Processes, Tata Mc Hill N. Delhi2. ASTME ,High Velocity Forming of Metals, PHI N. Delhi3. Serope Kalpakjian and Steven R. Schmid, Manufacturing Processes for Engg. Materials,

Pearson Education4. G.F Benedict, Non Traditional manufacturing, Marcel Dekker5. P.K Mishra, Non Conventional Machining, Narosa Publishing House N. Delhi


4/37




ADVANCE HEAT AND MASS TRANSFER (142104)

Credit: 04 L T P

4 0 0

PartA

1 Conduction:General heat conduction equation in rectangular, polar and spherical co-ordinates, one

dimensional heat conduction, variable thermal conductivity, composite walls, elementary

cases of two dimensional heat conduction, critical insulation thickness, unsteady heatconduction, heat transfer from extended surfaces, numerical methods.

PartB

1 Radiation:Introduction, properties and definitions, review of radiation principles (Plancks law,

Kirchoffs law, Stefan Boltzman law, Lamberts cosine law), radiation through non-absorbing media, Hottels method of successive reflections, radiation through absorbing

media, logarithmic decrement of radiation, apparent abosrptivity of simple shaped gasbodies, net heat exchange between surfaces separated by absorbing medium; radiation of

luminous gas flames.

PartC

2 Convection:Heat transfer in laminar flow, free convection between parallel plates, forced internal flow

through circular tubes, fully developed flow, velocity and thermal entry lengths, solutions

with constant wall temperature and with constant heat flux, forced external flow over a flatplate, the two dimensional velocity and temperature boundary layer equations, Karman

Pohlhousen approximate integral method, Heat transfer in turbulent flow, eddy heatdiffusivity.

PartD

3 Mass Transfer:Introduction, concentration, velocities and fluxes, Ficks law of diffusion, steady state

diffusion in common geometries, equimolal counter-diffusion in gases, steady state diffusionin liquids, transient mass diffusion in common geometries, mass transfer coefficient,

convective mass transfer.

Recommended Books:1. Eckert and Drake, Analysis of Heat and Mass Transfer, McGraw Hill

2. Grober, Erk and Grigul , Fundamentals of Heat Transfer, McGraw Hill

3. Holman J.P., Heat Transfer, McGraw Hill4. Schneider Addison Wesley, Conduction Heat Transfer

5. Siegel and Howel, Thermal Radiation, McGraw Hill

6. Rohsenhow and Choi ,Heat Mass and Momentum, Prentice Hall


5/37




MECHATRONICS (142105)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:What is mechatronics, systems, measurement systems, control systems, microprocessor-

based controllers, the mechatronics approach.

2. Sensors Strain Gauge, Potentiometer, Optical Encoders:Incremental and absolute encoders, linear variable differential transformer (LVDT),

piezoelectric, proximity sensor, resistance temperature detector, (RTD), thermistors,

thermocouple, hall effect sensor.

PartB

3.

Electronic Fundamentals:Signal conditioning process, operational amplifier, digital logic, logic gates, boolean algebra,

sequential logic, data acquisition systems, measurement systems, testing and calibration.

4. Precision Mechanical Actuation:Pneumatic actuation systems, electro-pneumatic actuation systems, hydraulic actuation

systems, electro-hydraulic actuation systems, mechanical systems, types of motion,kinematics, inverse kinematics, timing belts, ball screw and nut, linear motion guides, linear

bearings, harmonic transmission, bearings, motor / drive selection.

PartC

5. Electromechanical Drives:Relays and solenoids, stepper motors, DC brushed and brushless motors, DC servo

motors, AC / DC motors for non-servo motion drives, braking methods, pulse widthmodulated, bipolar driver, MOSFET drives, SCR drives, variable frequency drives.

6. Microprocessor and Computers:Introduction to 8085 , architecture, programming, computer interfacing, function of PLC,

architecture, components of PLC, selection of PLC, ladder logic diagram, logic functions:

latching, sequencing, counters, shift registers, jumpers, manipulation of data, arithmeticoperations

PartD

7. Input / Output Systems:Interfacing, input / output ports, interface requirements, peripheral interface adapters, serial

communication interface, direct memory access.

8.

Control System:System transfer function, laplace transformation and its applications, continuousand discrete processes, proportional control, integral control, differential control,

PID control, digital controllers, control system performance, controller tuning, adaptive

control, frequency response, PLC, PMC, introduction to fuzzy logic and neural networks.

Books Recommended:

1. Kamm, Understanding of Electro-Mechanical Engineering - An Introduction toMechatronics, Prentice-Hall of India.


6/37



M.Tech. (Mechanical Engineering)2. Koren, Computer Control of Manufacturing system, McGraw Hill.3. Groover, Production Systems and CIM, PHI.4. Maleki, Flexible Manufacturing systems, Prentice Hall.5. BC. Kuo, Feedback Control Systems, PHI.


7/37




OPTIMIZATION TECHNIQUES (142106)

Credit: 04 L T P

4 0 0

PartA

1. Definition of Optimization:Meaning of operations research, modeling in operation research, principles of modeling,introduction to linear and non-linear programming problems and formulation of problems.

2. Linear Programming:Modeling of linear programming problema few examples, Solution of linear programming

problem simplex method, two-phase method, M-method, Sensitivity analysis graphicalapproach

PartB

3. Transportation Model:Transportation problem, Vogels approximation method for finding feasible solution intransportation, methods for finding optimal solution, degeneracy in transportation problems,

maximization in transportation problems.

4. Assignment Model:Definition of assignment model, comparison with transportation problems, Hungarian

method to find optimal solution, travelling salesman problems, branch and bound method.

PartC

5. Queuing Theory:Types of queuing situation: queuing models with Poisson's input and exponential service,

their application to simple situations.

6. Dynamic Programming:Deterministic and probabilistic dynamic programmingPartD

7. CPM & PERT:Network situations where PERT & CPM can be applied, planning, scheduling & control,

work breakdown structure, Similarity and differences of CPM and PERT

8. Game theory: Two-person, Zero-sum games, Games with mixed strategies, Graphicalsolution, Solution by linear programming.

Books Recommended:

1. S.S. Rao, Engineering Optimization Theory and Practice by, New Age International2. Kalyanmoy Deb, Optimization for Engineering Design, PHI3. J.S Arora, Optimization Techniques, John Wiley


8/37




COMPUTER AIDED MANUFACTURING (142201)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Historical background, role of computers in manufacturing, automation, types of automation,

automation strategies.

2. Fundamentals of CNC Machines:CNC technology, functions of CNC control in machine tools, classification of CNC systems,

contouring system, interpolators, open loop and closed loop CNC system, CNC controllers,

hardware features, direct numerical control( DNC systems) and adaptive control.

PartB

3. Constructional Features of CNC Machines:Design considerations of CNC machines for improving machining accuracy, structural

members, slide ways, slides linear bearings, ball screws, spindle drives and feed drives, work

holding devices and tool holding devices, automatic tool changers. feedback devices,principles of operation, machining centers, tooling for CNC machines.

4. Part Programming For CNC Machines:Numerical control codes, standards, manual programming, canned cycles and subroutines,computer assisted programming, CAD/CAM approach to NC part programming, APT

language, machining from 3D models.

PartC

5. Introduction to Robot Technology in CAM:

Group technology and cellular manufacturing: introduction, part families, parts classificationand coding, production flow analysis, machine cell design. Computer aided process planning

( CAPP), types of process planning system, advantages of CAPP.

6. Production Planning and Control:Introduction to production planning and control, Shop Floor Control Systems, Just-in time

approach, Engineering Challenges in CAD/CAM, Product Data Management, Product

Modeling, Assemble and Tolerance Modeling.

PartD

7. Integrated Manufacturing System:Introduction toflexible manufacturing systems( FMS), different types of flexibilities in FMS,

type of FMS, machining system of FMS, tool management systems, work piece handling

system, FMS Control, Lay out considerations in FMS, advantages of FMS. Introduction tocomputer integrated manufacturing systems (CIMS), the future automated factory, trends in

manufacturing, human factors in future automated factory, the social impact. rapidprototyping, artificial intelligence and expert system in CIM.


9/37



M.Tech. (Mechanical Engineering)References:

1. Mikell P. Groover, Automation, Production System and CIMS, Prentice Hall of India, NewDelhi.

2. Ibrahim Zeid, CAD-CAM Theory and Practice, Tata McGraw-Hill Publishing Company.3. Yoram Koren, Computer Control of Manufacturing Systems, McGraw Hill Book Company.4. G.T.Smith, CNC-Machining Techniques-Vol. 1, 2 & 3, Verlag.5. Paul G. Ranky, Computer Integrated Manufacturing, Prentice Hall.6. Chang.T.C. & Wysk, An Introduction to Automated Process Planning, Prentice Hall Inc.


10/37




COMPUTER AIDED PROCESS PLANNING (142202)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Traditional process planning, process planning elements, product design evaluation, selection

of tooling and process parameters, operation sequence evaluation.

2. Group Technology:Introduction, advantages, part families, classification and coding systems, production flow

analysis, design of machine cells.

PartB

3. Production Systems at Operation Level:

Manufacturing support systems and concepts at the level of production processes, computergenerated time standards, machinability data system, cutting condition optimization.

4. Production Systems at Plant Level:

Communication oriented production information and control system (COPICS), materialrequirements planning, capacity planning, shop floor control and operation scheduling.

PartC

5. Automated Process Planning:Advantages of automated process planning, standardization of manufacturing process plans,

variant process planning, its features, and different stages, different variant systems,

advantages and limitations of variant process planning

6. Generative process planning, Its features, design strategies, planning modeling and coding

scheme, decision mechanism for software, decision trees for process, process information.PartD

7. Artificial intelligence, overview & application, search strategies for AI production systems,resolution and reduction systems, knowledge acquisition, machine selection, cutting tool

selection, software, various generative process planning systems, advantages of generative

process planning systems, case studies.

References:

1. Chang & Wysk , An Introduction to the Automated Process Planning, Prentice Hall.2. Groover & Zimmers, Computer Aided Design & Manufacturing, Prentice Hall.3. Gallagher & Knight, Group Technology; Prod. Method in Manufacturing, Ellis Hosewood.4. Groover, Automation; Production System & Computer Integrated Manufacturing, Prentice

Hall.


11/37




SIMULATION AND MODELLING (142203)

Credit: 04 L T P

4 0 0

PartA

1. Introduction and Overview:Concept of system, system environment, elements of system, simulation, a managementlaboratory, advantages limitations of system simulation, continuous and discrete systems.

2. Technique of Simulation:Monte-Carlo method, System simulation, comparison of simulation with analytical methods,

experimental nature of simulation, advantages, limitations and application of systemsimulation.

PartB

3. Numerical Computational Techniques:For continuous and discrete models. distributed lag models. Cobwals models, examples

involving numerical methods of analysis.

4. Simulation of Continuous Systems:Characteristics of a continuous system, comparison of numerical integration with continuoussimulation system, simulation of an integration formula, simulation of trajectories, pure

pursuit, serial pursuit, chemical reaction and auto pilot, analog methods, digital-analog

simulation time simulation, hybrid simulation.

PartC

5. Simulation of Discrete System:Time flow mechanisms, discrete and continuous probability density functions, generation of

random numbers, testing of random numbers for randomness and for auto correlation,generation of random varieties for discrete distribution, generation of random varieties for

continuous probability distributions-binomial, normal, exponential and beta distributions,

combination of discrete event and continuous models, the rejection method, simulation ofreliability, queuing and inventory problems.

6. Design of Simulation Experiment:Length of run, elimination of initial bias, variance reduction techniques, stratified sampling,antipathetic sampling, common random numbers, time series analysis, spectral analysis,

model validation, optimisation procedures, search methods, single variable deterministic case

search, single variable non-deterministic case search, regenerative technique.

PartD

7. Simulation of PERT:Simulation of maintenance and replacement problems, capacity planning production system,

reliability problems, computer time sharing problem, the elevator system.

8. Simulation Languages:Continuous and discrete simulation languages, block structured continuous languages,

special purpose simulation languages, SIMSCRIPT, GESS SIMULA importance and

limitations of special purpose languages.


12/37



M.Tech. (Mechanical Engineering)References:1. Loffick, Simulation and Modelling, Tata Mc-Graw Hill.2. Deo Narsingh, System Simulation with Digital Compute, PHI, N. Delhi3. D.S. Hira, System Simulation, S. Chand & Co., Delhi4. Meeiamkavil, Computer Simulation and Modelling, John Willey.5. Gerden, System Simulation, PHI, N. Delhi


13/37




FOUNDRY TECHNOLOGY (142204)

Credit: 04 L T P

4 0 0

PartA

1. Structure of Silica and Different Types of Clays:

Bonding mechanism of silica-water clay systems, swelling of clays, sintering adhesion andcolloidal clay, silica grain shape and size distribution standard permeability A.F.S. clay.

2. Characteristics:Ingradients and additives of moulding sand, core sands.

PartB4. Solidifications of Metals:

Nucleation, free energy concept, critical radius of nucleus, nucleation and growth in metals

and alloys, constitutional super cooling, columnar equiacquiesced and dendritic structures,freezing of alloys centerline feeding resistance, rate of solidification, time of solidification,

mould constant, fluidity of metals, volumes redistribution.

5. Various Moulding and Casting Processes:Hot box, cold box process, investment, shell moulding, full mould process, die casting,

ceramic shell mould, vacuum moulding etc.

PartC

6. Riser Design:Shape, size and placement, effect of appendages on risering, effective feeding distances for

simple and complex shapes, use of chills, gating design, filling time, aspiration of gases, top,

bottom and inside gating, directional solidifications stresses in castings, metal mould

reactions, expansion scale and metal penetration.PartD

6. Non-Ferrous Die-castingof Aluminum and its alloys, brass and bronze.

7. Inspection and testing of casting i.e. visual, mechanical, ultrasonic, dye penetration,magnetic particle and x-ray., Casting Defects.

References:

1. Flinn, Fundamentals of Metals Casting, Addison Wesley.2. , Heine Loper and Resenthal, Principles of Metal Casting, Mc-Graw Hill.3. Hielel and Draper Product Design & Process Engineering, Mc-Graw Hill.4. Salman & Simans, Foundry Practice, Issac Pitman.5. ASME, Metals Handbook- Metal Casting.


14/37




MANAGEMENT OF PRODUCTION SYSTEM (142205)

Credit: 04 L T P

4 0 0

PartA

1. System Theory and Concepts:

System defined, functional elements of a system, general systems theory, systems theory andorganization, systems concept and management, the system approach, planning and system

concepts. Control and system concepts, information and system concepts.

2. Quantitative Techniques of System Analysis:

System analysis, problem solving, scientific method, mathematical analysis models,computers, techniques of analysis, linear programming input output analysis queuing monte

cargo techniques, simulation, industrial dynamics.

Part

B3. Behavioral Aspect of System Design:

The motivation factor in system design, leadership factor in systems design, the need for

systematic human relationships, the need for systems change, resistance to change,behavioral consequence of system changes, microanalysis of complex, man-machine open

systems concept as a basis of human integration, meeting the human and social problems.

PartC

4. Flow System:Increasing complexity in distribution and production, increasing cost of a distribution, the

total flow system, planning the transformation, the service system integration systems.

5. Program Management:

Impact of advancing technology, large scale integrating systems. Program-managementconcept functional stage of program-management organizational medications, matrix

organization applications of program-management.

PartD

6. Management Cybernetics:Management cybernetics in controlling a manufacturing firm, production and inventory

control systems, production, inventory and employment control system, the enterprise controlsystems.

References:

1. Eilon, Elements of production planning and control, Macmillan.2. Donald Bower son and David Closes, Logistical Managemen, Mc-Graw Hill.3. James Dilworth, Production and Operations Management, Mc-Graw Hill.4. M. Therese Flaherty, Global Operations Management, Mc-Graw Hill.5. Nauhria, R.N. & Parkash Rajnish, Management of Systems.6. Elwood, Modern Production Management, S. BuffaWiley, Eastern


15/37




PRODUCT DESIGN & DEVELOPMENT (142206)

Credit: 04 L T P

4 0 0

PartA

1. Basics of Product Design:

Introduction to product design, concept, terminology, principles, requirements of a goodproduct design, product types and design considerations for engineering, production

consumption cycle, flow and value addition in production consumption cycle.

2. Basic Design Considerations:

Functional & aesthetics consideration, basic design considerations, role of aesthetics inproduct design, basic concept and elements of visual design, functional design practice.

PartB

3. Manufacturing Consideration:Producibility requirements in the design of machine components, forging design, pressed

component design, design for machining, ease of location and clamping, some additional

aspects of production design, design of powder metallurgical parts, redesigning on basis ofproduction consideration.

PartC

4. Legal & Economic Considerations in Design:

Product value, design for safety, reliability and environmental considerations, economicanalysis, profit and competitiveness, break even analysis, economics of a new product

design, concurrent design, reverse engineering and rapid prototyping.

PartD

5. Value Engineering:Definition of value, nature, measurement & importance of value, maximum value, normal

degree of value, the value analysis job plan, creativity, problem solving and value analysis,

value engineering, cost reduction, materials and process selection in value engineering.

6. Product Development:Definition, concept and objective, role of designer in product development, manufacturing &

economic aspects of product development, product promotion & development.

References:

1. Kail T Ulrich and Steven D Eppinger, Product Design and Development, Mcgraw-hill2. AK Chitale and Gupta, Product Design and Engineering, Prentice-Hall of India Pvt Ltd3. Niebel & Draper, Product Design and Process Engineering, McGraw-Hill New York4. William H. Middendorf, Richard H. Engelmann , Design of Systems and Devices, Marcel

Dekker


16/37




QUALITY ASSURANCE & RELIABILITY ENGINEERING

(142207)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Inspection, definition, objectives, kinds of inspection, centralized inspection, decentralized

inspection, functions of inspection, quality control- need and functions, difference between

inspection and quality control.

PartB

2. Statistical Concepts and Control Charts:

Review of fundamental statistical concept, frequency distribution, central tendency, measuresof dispersion, probability distributions, statistical quality control, theory of control charts,

control charts for variables and attributes (X, R, P, np and C chart), their advantages and

disadvantages, Applications.

PartC

3. Acceptance Sampling:Introduction, advantages and disadvantages, operating characteristics curve, producer's and

consumer's risk, quality indices for acceptance sampling plans, types of sampling plans-single double sequential sampling plan, sampling plan for variables, continuous sampling

plans, skip lot sampling plans, chain sampling plan.

4. Quality Management:

ISO 9000 and TQM concepts - Quality circles, tools Zero defect management, 6 sigma

Quality Function Deployment (QFD).PartD

5. Reliability:Introduction, factors effecting reliability, failure and its types, failure curve, reliability and its

management, MTBF, MTTF, relationship b/w reliability failure rate and MTBF, and its

characteristics, reliability predictions and analysis, system reliability analysis, reliability test

and life testing plans, types of test, maintainability and availability, reliability models Series, Parallel, Hybrid.

References:

1. R.C. Gupta, Statistical Quality control.2. Harrism; M. Wadsworth, Modern Methods for Quality Control and Improvement.3. E.L. Grant, Statistical Quality control.4. B.L. Ams Tadter, Reliability Mathematics.5. Amitava Mitra, Fundamental of Quality Control and Improvement.6. A.K. Gupta, Reliability Engineering and Tero technology.


17/37




DESIGNS OF EXPERIMENTS (142208)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Strategy of experimentation, some typical applications of experimental design, basic

principles, guidelines for designing experiments, a brief history of statistical design, using

statistical design in experimentation.

2. Simple Comparative Experiments:Introduction, basic statistical concepts, sampling and sampling distribution, inferences about

the differences in means, randomized designs, inferences about the differences in means,paired comparison designs, inferences about the variances of normal distributions.

Part

B3. Randomized Block Designs:

Randomized complete block design, latin square design, balanced incomplete block design.

4. Introduction to Factorial Design:Basic definition and principles, advantages of factorials, the two factor factorial design,

general factorial design, fitting response curves and surfaces, blocking in a factorial design.

PartC

5. Fitting Regression Models:Introduction, linear regression models, estimate of parameters in linear regression models,

hypothesis testing in multiple regression, confidence intervals in multiple regression,

prediction of new response observations, regression model diagnostics, testing for lack of fit

6. Analysis of Variance (ANOVA):Introduction, example of ANOVA process, degrees of freedom, error variance and pooling,

error variance and application, error variance and utilizing empty columns, the F-test.

PartD

7. Taguchi Method of Design of Experiments:Concept design, parameter design, tolerance design, quality loss function, signal-to- noise

ratio, orthogonal array experiments, analysis of mean(ANOM), quality characteristics,selection and testing of noise factors, selection of control factors, parameter optimization

experiment, parameter design case study.


18/37



M.Tech. (Mechanical Engineering)References:1. Douglas C Montgomery, Design and Analysis of Experiments, John Wiley.2. John P.W.M., Statistical Design and Analysis of Experiments, Macmillan.3. Montgomery D.C., Runger G. C., Introduction to Linear Regression Analysis.4.

Myres R.H., Montgomery D. C., Response Surface Methodology: Process And ProductOptimisation Using Designed Experiments, Wiley, New York.

5. Taguchi, Introduction to Quality Engineering, Asian Productivity Organisation, G. UNIPUB,White Plains, New York.

6. Taguchi, System of Experimental Design: Engineering Methods to Optimize Quality andminimize Cost, G. UNIPUB, White Plains, New York.

7. J. Wesley Barnes, Statistical Analysis for Engineers And Scientists, McGraw Hill Inc.


19/37




FINITE ELEMENT ANALYSIS (142209)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Finite element methods, history and range of applications.

2. Finite Elements:Definition and properties, assembly rules and general assembly procedure, features ofassembled matrix, boundary conditions.

PartB

3. Continuum Problems:Classification of differential equations, variational formulation approach, Ritz method,

element equations from variations. Galerkins weighted residual approach, energy balancemethods.

PartC

4. Element Shapes and Interpolation Functions:Basic element shapes, generalized coordinates, polynomials, natural coordinates in one-, two-

and three-dimensions, Lagrange and Hermite polynomials, two-D and three-D elements for

Co and C

1 problems, coordinate transformation, iso-parametric elements and numerical

integration.

PartD

5. Applications & Case Studies:Application of finite element methods to elasticity and structural, heat transfer, fluid-flow,

lubrication and general field problems.

References:

1. K.H. Huebner, The Finite Element Method for Engineers, John Wiley, New York.2. Jeffery M. Steche, Applied Finite Element Modeling, Marcel Dekker, New York.3. O.C. Zienkiewicz, The Finite Element Method, Tata McGraw Hill, New Delhi.4. Desai & Abel, Introduction to the FEM, (CBS)-affiliated to East West Press, New Delhi.5. George R. Buchanan, Finite Element Analysis, Schaum MGH, New York.6. Chandrupatla & Belgundu, Introduction to Finite Elements in Engineering, Prentice Hall of

India, New Delhi.

7. J.N. Reddy, An Introduction to the Finite Element Method, McGraw Hill, New York.8. Cheung Y.K, Lo.S.H.,Leung A.Y.T Finite Element Implementation, Blackwell Science Ltd,London.


20/37




WELDING TECHNOLOGY (142210)

Credit: 04 L T P

4 0 0

PartA

1. Introduction:Basic classification of welding processes, weldability, weld thermal cycle, metallurgy of

fusion welds, solidification mechanism and micro structural products in weld metal,

epitaxial, cellular and dendritic solidification, metallurgical changes in weld metal, phasetransformation during cooling of weld metal in carbon and low alloy steel, prediction of

microstructures and properties of weld metal, heat affected zone, re-crystallization and grain

growth of HAZ, gas metal reaction, effects of alloying elements on welding of ferrousmetals.

2. Welding Power Sources:Arc welding power sources, basic characteristics of power sources for various arc welding

processes, duty cycles, AC/DC welding power source, DC rectifiers, thyristor controlled

rectifiers, transistorized units, inverter systems.

PartB

3. Welding Arc:

Arc efficiency, temperature distribution in the arc, arc forces, arc blow, electricalcharacteristics of an arc, mechanism of arc initiation and maintenance, role of electrode

polarity on arc behavior and arc stability, analysis of the arc, arc length regulation in

mechanized welding processes.

4. Fusion Welding Reviews:

Critical reviews of manual metal arc welding (MMAW) GTAW, GMAW, FCAW and CO 2welding processes, plasma arc, submerged arc welding, electro gas and electro slag welding,

analysis of the process.

PartC

5. Coated Electrodes:

Electrode coatings, classification of coatings of electrodes for SMAW, SAW fluxes, role of

flux ingradients and shielding gases, classification of solid and flux code wires.

6. Metal Transfer & Melting Rate:

Mechanism and types of metal transfer, forces affecting metal transfer, modes of metal

transfer, metal transfer in various welding processes, effect of polarity on metal transfer and

melting rate.

Part

D7. Solid State Welding:

Theory and mechanism of solid state welding, techniques and scope of friction welding,diffusion welding, cold pressure welding and ultrasonic welding, high energy rate welding.

Analysis of the Process.

8. Welding Techniques:Technique, scope and application of the electron beam and laser welding processes, under

water welding - process & problem.


21/37



M.Tech. (Mechanical Engineering)References:1. R.S.Parmar, Welding processes & Technology, Khanna Publishers.2. S.V. Nandkarni, Modern Arc Welding Technology, Oxford & IDH publishing Co.3. L.M.Gourd, Principles of Welding Technology, ELBS/ Edward Arnold.4.

Richard L. Little, Welding & Welding Technology, Mc-Graw Hill.5. Rossi, Welding Technology, Mc-Graw Hill.


22/37




VIBRATION ANALYSIS (142211)

Credit: 04 L T P

4 0 0

PartA

1. Fundamentals:Introduction of vibrations, harmonic motion, vector representation. Beats phenomenon,

complex method of representing harmonic vibrations, Fourier series and harmonic

analysis, analytical and numerical methods of harmonic analysis.

2. Free Vibrations:Undamped free vibrations of single degree of freedom systems, viscously damped free

vibrations of single degree of freedom systems, energy method for natural frequency,

equivalent stiffness of spring combinations.

Part

B3. Forced Vibrations of Damped 1-DOF Systems:Forced vibrations of single degree of freedom system with constant harmonic excitation,

forced vibrations due to excitation of support absolute amplitude and relativeamplitude.

4. Vibration Isolation, Transmissibility & Measurement:Force transmissibility, motion transmissibility, vibration isolation, vibration measuringinstruments for displacement, velocity, acceleration and frequency measurement.

PartC

5. Two Degrees of Freedom Systems:Principal modes of vibration of a 2-DOF system, systems with damping, undamped

forced vibrations under harmonic excitation, vibration absorbers: undamped dynamicabsorber, centrifugal pendulum absorber, dry friction damper, untuned viscous damper.6. Multi Degree of Freedom SystemsExact Analysis:

Governing equations, influence coefficients, flexibility coefficients and stiffness

coefficients, Maxwells reciprocal theorem, generalized coordinates and coordinate

coupling, natural frequencies and mode shapes, orthogonal properties of normal modes,modal analysis, forced vibrations by matrix inversion.

PartD

7. Numerical Techniques for Multi Degree of Freedom Systems:Rayleighs method for finding the first natural frequency, Dunkerleys method, Stodolasmethod, method of matrix iterations, Holzers tabulation method, critical speed of shaft

with single and multiple unbalanced discs without damping.8. Transient Vibrations:Laplace transformation, system response to different inputs, viz, impulsive, step andpulse inputs, phase plane method, shock spectrum.


23/37




1. S. Timoshenko, Vibration Problems in Engineering, D. Van Nostrand Company Inc., NewYork.

2. W. Weaver and D.H. Young , Fundamentals of Mechanical Vibrations.3. P. Srinivasan, Mechanical Vibration Analysis, McGraw-Hill Companies4. S. Graham Kelly, Fundamentals of Mechanical Vibrations, McGraw-Hill.5. William W. Seto, Theory and Problems of Mechanical Vibrations.6. G.K. Grover, Mechanical Vibrations, Roorkee Press.7. S. S. Rao, Mechanical Vibrations, Addison Wesley


24/37




AUTOMOTIVE DESIGN (142212)

Credit: 04 L T P

4 0 0

PartA

1. Automotive Engineering Development:Innovations and inventions, engine developments, (transmission, steering, suspension, brake)system development, interior refinement, safety design.

2. Modern Materials and Manufacturing Challenge:Structure, properties and manufacturing technology of automotive materials, material

selection, design to manufacture as a single process and IPPD

3. Body Design:Styling process, aerodynamics, chassis design & analysis.

Part

B4. Crashworthiness and its Influence on Vehicle Design:

Accident and injurt analysis, vehicle impact (general dynamics & crush characteristics),

structural collapse and its influence upon safety.

5. Noise, Vibration and Harshness:Vibration control, Fundamentals of acoustics, Sound measurement, general noise control

principles.

6. Occupant Accommodation: An Ergonomics Approach:Eight fundamental Fallacies, ergonomics in the automotive industry, strategies for improving

occupant accommodation and comfort.

PartC

7. Suspension System and Components:Factors effecting design, mobility of suspension mechanisms, kinematic analysis, roll centeranalysis, force analysis, vehicle ride analysis, controllable suspensions.

8. The design of engine Characteristics for Vehicle Use

9. Transmissions and Driveline:Manual gearbox, automatic transmission, continuously variable transmission.

10. Braking Systems:Fundamentals of braking, brake proportioning and adhesion utilization, materials design.

PartD

11. Control Systems in Automobiles:Automotive application of sensors, EMS, electronic transmission control, integration of EMS

and TCS, chassis control system, multiplex wiring system, vehicle safety and securitysystem, on-board navigation system.

12. Failure Prevention:Important aspects of failures in real engineering world, testing and failure prediction,

automotive technology and the importance of avoiding failures.

13. Future Trends in Automobile Design:Mechanical possibilities, electronic and electrical possibilities.


25/37




1. Julian Happian-Smith, Butterworth , An Introduction to Modern Vehicle Design, AButterworth-Heinemann

2. Heisler, Advanced Vehicle Technology, ISBN.3. R. and Harding, Automobile Design: Twelve Great Designers and Their Work, SAE.4. Barnard, R.H., Road Vehicle Aerodynamic Design, Longman.5. Peacock, B. and Karwowski, Taylor & Francis., Automotive Ergonomics, CRC Press6. Nwagboso, C.O., Chapman and Hall , Automotive Sensory Systems, Chapman & Hall


26/37




SYSTEM DESIGN (142213)

Credit: 04 L T P

4 0 0

PartA

1. System Theory and Concepts:Engineering and engineering profession, engineer, science and scientist, engineering andsociety, social responsibility and engineering, new challenges to engineers in the present

socio-political-economic environment.

2. System Design:Design, designer, qualities in a designer, system, its characteristics and system design cycle,features and steps of inventiveness, obstacles and aids to creativity, systematic search for

new ideas, information and information resources, procedure to obtain information and

information handling.PartB

3. Engineering Analysis and Decision Making:Methods of engineering analysis, decision making and its requirements, methods for decisionmaking, steps in engineering design process.

4. Problem Formulation:Need, analysis, identification of surrounding problems, problem formulation criterion,feasibility study, physical principles, concept formation, checking, estimations & bidding,subjective and quantitative analysis.

PartC

5. Preliminary Design:Consideration of alternative models, sensitivity analysis, compatibility analysis, optimization,rechecking.

6. Detail Design:Steps in detailed design, factors affecting detailed design, importance of technical knowledgeand manufacture processes, detailed design and production drawings.

PartD

7. Revision:Prototype testing and technique, evaluation of predicted performance and generalization,

revision and report writing.

8. Case studiesto be discussed involving systems design process.

References:1. J.B. Dixon, An introduction to System Design, Mc-Graw Hill.2. D. K. Aggarwal and S.L. Singla, Systems Design.3. M. Asimow, Introduction to Design, PHI, N. Delhi


27/37




INDUSTRIAL AUTOMATION AND ROBOTICS (142214)

Credit: 04 L T P

4 0 0

PartA

1. Concept of Automation in Industry:Mechanization and automation, classification of automation systems, difference between

hard automation and robotic automation.

2. Air Cylinders:Their design and mounting, pneumatic and hydraulic valves- flow control valves, metering

valves, direction control valves, hydraulic servo systems, pneumatic safely and remote

control circuits.

PartB

3. Basis of Automated Work Piece Handling:Working principles and techniques, job orienting and feeding devices, transfer mechanisms-automated feed cut of components, performance analysis.

4. Assembly Automation:Automated packaging and automatic inspection.

PartC

5. Introduction to robot technology:Robot physical configuration and basic robot motions

6. Types of manipulators:Constructional features, servo and non servo manipulators.

PartD

7. Feedback systems and sensors:Encoders and other feed back systems, vision, ranging systems, tactile sensors.8. Concept of spatial desecrations and transformations, manipulator kinematics, Inverse

manipulator, kinematics Jacobians, velocity and static forces, manipulator dynamics

References:

1. Johon. J. Craig, Introduction to Robotics, Pearson Education.2. Saeed. B. Niku. Introduction to Robotics, Pearson Education Asia..3. Andrew Parr, Hydraulics and Pnematics (HB)", Jaico Publishing House, 1999.4. Dudleyt, A. Pease and John J. Pippenger, Basic Fluid Power , Prentice Hall,5. Anthony Esposite, Fluid Power with Applications, Prentice Hall, 1980.6. K.S.Fu, R.CGonzalez and C.S.G. Lee, Robotics control, Sensing, Vision and intelligence,

McGrawHill,1987

7. Yoram Koren, Robotics for Engineers, Mc-Graw Hill.8. Tunnel, Industrial Robots Vol. I, SME.9. Deb, S.R., Robotics Technology and Flexible Automation, Tata McGraw Hill,199410.S. R. Majumdar, Pneumatic System Principles and Maintenance, Tata Mc Graw Hill, 1995.


28/37




INDUSTRIAL TRIBOLOGY (142215)

Credit: 04 L T P

4 0 0

PartA

1 Introduction:Friction, wear and lubrication, types of engineering contacts, conforming and non-

conforming, types of motion, rubbing, sliding, oscillating, rolling and surface of interactions,

elastic and plastic deformations, properties of materials, surface energy and flash temptheory.

2 Friction:Law of sliding friction, concept of adhesion, Taylors model of friction, measurement offriction.

Part

B3 Wear:

Laws of wear, types of wear such as adhesive, declamation, abrasive, fatigue, corrosive,

fretting erosive, electrical and oxidative, measurement of wear in dry atmosphere anddifferent environments preventive, control of wear, wear of cutting tool and dies, study of

abrasion in grinding, lapping and honing.

PartC

4 Lubricants:Mechanisms of lubricants, boundary, squeeze film hydrodynamic and elasto hydrodynamic

and hydrostatic lubricants plasto hydrodynamic lubricants, solution of Reynolds equation in

two and three-dimensional flow, pressure distribution load carrying capacity friction forces in

oil film and coefficient of friction in journal bearing, solid lubricants, types and applications.5 Bearing Design:

Design of bearing, clearance in journal bearing, minimum film thickness, sommar-fieldnumber, oil grooves and flow of oil in axial and circumferential grooves cavitations and

turbulence in oil bearings, heat generation and cooling of bearings (hydrostatic and dynamic)

and their applications in machine tools, design of air bearing and other gas bearing.

PartD

6 Rolling Friction:Reynoldss slip, concept, selection of roller bearings and their methods of lubrication , design

aspects and modes of bearing failures and also hydrodynamic lubrication.

7 Solid Lubricants: Solid lubricants and its applications in metal forming processes.Recommended Books:

1. Sharma & Aggarwal A text book ,Kataria2. Powell ,A Machine Design Handbook ,McGraw Hill3. Shigley, Mischke & Brown ,Standard handbook of machine design ,McGraw Hill4. Dr.B.S.Prabhu Industrial Tribology ,McGraw Hill


29/37




METAL FORMING (142216)

Credit: 04 L T P

4 0 0

PartA

1 Classification of Metal Forming Processes:Elementary theory of plasticity, stress / strain / strain-rate characteristics of materials, yieldcriteria of metals, formability.

2 Mechanics of Forming Process:Rolling, process parameters, pressure distribution and roll separating force, rolling pressure,

driving torque and power requirements.

PartB

3 Forging:Determination of forces in strip forging and disc forging, defects in forged components.

4 Drawing:Drawing stresses, limiting draw ratio, factors affecting drawability determination of force

and power in wire drawing, determination of maximum allowable reduction, deep drawingforce analysis. defects in drawn components.

PartC

5 Bending:Bendability, determination of work load and spring back.

6 Extrusion:Process parameters, determination of work load from stress analysis and energy

considerations, power loss, hydrostatic extrusion, pressure required to extrude, variables

affecting the extrusion process.PartD

7 Punching & Blanking:Two-dimensional deformation model and fracture analysis, determination of working force.

8 High Energy Rate Forming:Classification, comparison of conventional and high speed forming, Introduction to High

Energy Rate Forming Processes (HERF).

Recommended Books:

1. J. W. Rowe, An Introduction to the Principles of Industrial Metal Working, Edward Arnold,London

2. B. L. Juneja, Fundamentals of Metal Forming Processes, New Age International Publishers,N. Delhi.3. Avitzur, Metal Forming Analysis, McGraw Hill, New York4. Johnson & Millore, Plasticity for Mechanical Engineers, Van Nostrand, London5. Ghosh & Malik, Manufacturing Science, Affiliated East-West Press, New Delhi.6. Samy R. Narayan : Metal Forming Technology, Ahuja Book Publishers, New Delhi


30/37




THEORY OF CUTTING & MACHINE TOOL DESIGN (142217)

Credit: 04 L T P

4 0 0

PartA

1. Theory of Metal Cutting:Mechanism of metal cutting, cutting forces, chip formation, merchants circle diagram,calculations, system of tool nomenclature, tool geometry, machinability, tool life, cutting tool

materials, cutting fluids. Abrasive machining- mechanism of grinding, lapping and honing.

2. Introduction To Machine Tool Design:Introduction to metal cutting machine tools, kinematics of machine tools, basic principles ofmachine tool design.

PartB

3. Design of Drives:Design considerations of electrical, mechanical and hydraulic drives in machine tool,selection of speeds and feeds, stepped and stepless regulation of speed, estimation of power

requirements and selection of motor for metal cutting machine tool spindles, design of gearbox.

4. Design of Machine Tool Structures:Principles, materials, static & dynamic stiffness, shapes of machine tool structures, design of

beds, columns, housings, tables, ram etc.

PartC

5. Design of Spindles, Guide ways and Slide ways:Design of machine tool spindles- materials of spindles, machine tool compliance, design of

bearings- anti friction bearings, sliding bearings, design of guide ways and slide ways.6. Design of Control Mechanisms:

Basic principles of control, mechanical, electrical, hydraulic, numeric and fluid controls,

Selection of standard components, dynamic measurement of forces and vibrations in machinetools, stability against chatter, use of vibration dampers.

PartD

7. Automation, Testing and Standardization:Automation drives for machine tools, degree of automation, semi-automation, analysis of

collet action, design of collet, bar feeding mechanism, tooling layout, single spindle

mechanism, analysis, Swiss type automatic machine, loading and unloading, transfer-devices,

modulator-design concept, in process gauging, acceptance tests and standardization of

machine tools.


31/37




1. Juneja.B.L. and Sekhon.G.S, Fundamentals of metal cutting and machine tools, New AgeInternational (P ) Ltd., N. Delhi

2. M.C.Shaw, Metal Cutting Principles, Oxford Clarendon Press.3. A.Bhattacharya, Metal Cutting Theory and Practice, New Central Book Agency( P) Ltd,

Calcutta.

4. Arshinov & Alelrev, Metal Cutting Theory and Cutting Tool Design, MIR Publishers,Moscow.

5. N.K.Mehta, Machine Tool Design, Tata Mc-Graw Hill, N. Delhi6. G.C.Sen and A.Bhattacharyya, Principles of Machine Tools, New Central Book Agency ( P)

Ltd.

7. Ackerkan, Machine Tool Design Vol 1-4, MIR Publishers, Moscow.8. Koenigsberger, Design Principles of Metal Cutting Machine Tools, Pergamon Press.9. Tobias, Machine Tool Vibration, Blackie Oxford London.


32/37




RESEARCH METHODOLOGY (142218)

Credit: 04 L T P

4 0 0

PartA

1 Nature and Objectives of research Methods of Research:Historical, descriptive and experimental, alternative approaches to the study of the researchproblem and problem formulation, formulation of hypotheses, feasibility, preparation and

presentation of research proposal.

PartB

2 Introduction to Statistical Analysis:Probability and probability distributions binomial, Poisson, exponential and normal

distributions and their applications.

3 Sampling:Primary and secondary data, their collection and validation, methods of sampling, simplerandom sampling, stratified random sampling and systematic sampling.

PartC4 Regression and correlation analysis, tests of significance based on normal, t and chi-square

distributions, analysis of variance.

5 Basic principles of design of experiments, completely randomized and randomized blockdesigns.

PartD6 Edition, tabulation & testing of hypotheses, interpolation of results, presentation, styles for

figures, tables, text, quoting of reference and bibliography, use of software for statistical

analysis like SPSS, Mini Tab or MAT Lab, report writing, preparation of thesis, use ofsoftware like MS office.

The course will include extensive use of software, report writing and seminars in the tutorial

class.

Recommended Books:

1. C.R. Kothari, Research Methodology, Wishwa Prakashan2. P.G. Tripathi, Research Methodology, Sultan Chand & Sons, N. Delhi3. Fisher, Design of Experiments, Hafner4. Sadhu Singh, Research Methodology in Social Sciences, Himalya Publishers5. Stoufferetal, Measurement & Prediction, Wiley, N. York6. J.W. Barnes, Statistical Analysis for Engineers & Scientists, McGraw Hill, N. York7. Donald Cooper. Business Research Methods, Tata McGraw Hill, N. Delhi


33/37




ENTREPRENEURSHIP (142219)

Credit: 04 L T P

4 0 0

PartA

1. Concept of Entrepreneurship:Entrepreneurship and small scale industry, need for promotion of entrepreneurship,

entrepreneurship development programmes (EDP), personality characteristics ofentrepreneur.

PartB

2. Identification of Investment Opportunities:Governmental regulatory framework, industrial policy, industrial development and regulation

act, regulation of foreign collaboration and investment, foreign exchange regulation act,incentives for export oriented units, incentives for units in industrially backward areas,

incentives for small scale industry, government assistance to SSI, how to start a SSI, list ofitems reserved for SSI, Scouting for project ideas, preliminary screening, project

identification for an existing company.

PartC

3. Market and Demand Analysis:Information required for market and demand analysis, market survey, demand forecasting,

uncertainties in demand forecasting.

PartD

4. Cost of Project and Means of Financing:Cost of project, means of financing, planning the capital structure of a new company, term

loan financial institutions, cost of production.

5. Financial Management:Concept and definition of financial management, types of capital of finance, reserve and

surplus, concepts and liabilities, profit and loss statement, balance sheet, depreciation,

methods of calculating depreciation break even analysis.

Books:

1. E.D.I. Ahmedabad, Publication regarding Entrepreneurship.2. Prasanna chandra, Project Preparation, Appraisal Budgeting and Implementation, TMH.3. Entrepreneurship, TTTI4. C.S.Gupta & N.P.Srinivasan, Entrepreneurial Development.5. Entrepreneurship Development Practice & Planning, S.Chand.6. Entrepreneurship of Small Scale Industries. M.U.Deshpanda C.B.I.


34/37




SELF STUDY AND SEMINAR (142107)

Credit: 03

Each student will be required to prepare a Seminar Report and present a Seminar on a topic in

any of the areas of modern technology related to Mechanical Engineering including

interdisciplinary fields. The topic/title will be chosen by the student in consultation with the

Faculty Advisor allocated to each student. The student will be required to submit the SeminarReport and present a talk to an audience of Faculty/Students in open defense in front of the

Seminar Evaluation Committee having Faculty Advisor as one of its members. The Seminar

Evaluation Committee will be constituted by Head of Department.


35/37




SEMINAR (142108)

Credit: 03

Each student will be required to prepare a Seminar Report and present a Seminar on a topic in

any of the areas of modern technology related to Mechanical Engineering including

interdisciplinary fields. The topic/title will be chosen by the student in consultation with the

Faculty Advisor allocated to each student. The student will be required to submit the SeminarReport and present a talk to an audience of Faculty/Students in open defense in front of the

Seminar Evaluation Committee having Faculty Advisor as one of its members. The Seminar

Evaluation Committee will be constituted by Head of Department.


36/37




PROJECT (142109)

Credit: 03

Each student will be required to complete a Project and submit a Project Report on a topic on any

of the areas of modern technology related to Mechanical Engineering including interdisciplinary

fields. The title and objectives of the Project will be chosen by the student in consultation with

the Project Guide allocated to each student. The student will be required to present a talk to anaudience of Faculty/Students in open defense in front of the Project Evaluation Committee

having Project Guide as one of its members. The Project Evaluation Committee will be

constituted by Head of Department for the purpose of evaluation for internal assessment.


37/37




DISSERTATION (142110)

Credit: 10

Each student will be required to complete a Dissertation and submit a written Report on the topic

on any of the areas of modern technology related to Mechanical Engineering including

interdisciplinary fields in the Final semester of M.Tech. course. The title and objectives of theDissertation will be chosen by the student in consultation with the Supervisor (s) and the same

will be required to be defended by the student in open defense in front of the Dissertation

Monitoring Committeeapproved by the Head of Department. The title and objectives will beapproved by the Dissertation Monitoring Committee having main Supervisor as one of its

members. The progress will also be monitored at weekly coordination meetings with the

Supervisor (s). The student will be required to present a talk to the gathering in open defense in

front of the Dissertation Monitoring Committee having main Supervisor as one of its members.

The Dissertation Monitoring Committee will be constituted by Head of Department for thepurpose examining the suitability of the work carried out by the student in the Dissertation for its

evaluation by the external examiner. The Dissertation will be sent to the External Examiner forits evaluation only after its due approval by the Dissertation Monitoring Committee. The external

evaluation will be done jointly by the main Supervisor and external examiner appointed by the

Head of Department. The dissertation (non-credit course) will be either approved or rejected.The external examiner will evaluate the dissertation and the viva-voce will be fixed by the Head

of Department. After Viva-voce, the examiners (internal and external) will approve/reject the

dissertation. In case, the dissertation is rejected, the candidate will rework and resubmit the

dissertation. The dissertation will be again be evaluated jointly by the same external examiner

and the Main Supervisor.

Date post:	18-Oct-2015
Category:	Documents
Upload:	san-deep-sharma
View:	16 times
Download:	0 times

Syllbus M.tech ME

Documents