SERVICE MANUAL
42″ COLOR LCD TELEVISION
LC420SS8
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1How to initialize the LCD Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.
1-1 A81H1SP
SPECIFICATIONS
< TUNER / NTSC >ANT. Input ---------------------- 75 ohm Unbal., F type
< TUNER / ATSC >
< LCD PANEL >
< VIDEO >
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
2. Syncronizing Sens.TV.ch.4
CA.ch.31CA.ch.87
dBµdBµdBµ
---------
202023
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
2. ATSC Dynamic Range (min / max)ch.4ch.10ch.41
dBmdBmdBm
---------
-76/+6-76/+6-76/+6
Description Condition Unit Nominal Limit
1. Native Pixel Resolusion HorizontalVertical
pixelspixels
19201080
------
2. Brightness (w / filter) --- cd/m2 500 ---
3. Viewing Angle HorizontalVertical
°°
------
-89 to +89-89 to +89
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
5±55±5
------
2. Color Temperature---xy
°K 120000.2720.278
---±10%±10%
3. Resolution (composite video) HorizontalVertical
lineline
720480
------
1-2 A81H1SP
< AUDIO >All items are measured across 8 Ω load at speaker output terminal with L.P.F. / Video1 Input.
Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.
Description Condition Unit Nominal Limit
1. Audio Output Power 10% THD: Lch/Rch W 10.0/10.0 9.0/9.0
2. Audio Distortion 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
3. Audio Freq. Response (NTSC) -6dB: Lch-6dB: Rch
HzHz
20 to 10 k20 to 10 k
------
2-1 LTVN_ISP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV Circuit1. Before returning an instrument to the
customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
READING SHOULD NOT BE ABOVE 0.5 mA
EARTHGROUND
_
DEVICELEAKAGECURRENT
TESTER
+BEINGTESTED
2-2 LTVN_ISP
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Hot Chassis Warning -
a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
2-3 LTVN_ISP
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.
H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.
L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.
2-4 LTVN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d), (d’)
110 to 130 V U.S.A. or Canada
≥ 3.2 mm (0.126 inches)
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V U.S.A. or Canada
0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible
parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
3-1 TVN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
Pb free mark
Fig. S-1-1
3-2 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
3-3 TVN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
3-4 TVN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
4-1 A81H1DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
2. Disassembly Method
Note:
(1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. N = Nut, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the Table."
Step/Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
[1] Stand Base D1 4(S-1), 4(S-2) ---
[2] Stand Cover D1 --------------- ---
[3] Rear Cabinet D1 6(S-3), 2(S-4), 11(S-5) ---
[4] Inverter Power CBA
D2D5
5(S-6), *CN701, *CN702, *CN751, *CN752, *CN753
---
[5] Jack Holder(D) D2 (S-7), 2(S-8), 2(S-9) ---
[6] Shield Box D2 5(S-10), 2(S-11), (N-1) ---
[7] Digital Main CBA Unit
D2D5
*CN200, *CN201, *CN202, *CN203, *CN3707, *CN4201
---
[8] Jack CBA D3D5
5(S-12), *CL7002A, *CN7002 ---
[2] Stand Cover
[5] Jack Holder(D)
[16] IR SensorCBA
[14] Function CBA
[1] Stand Base
[3] Rear Cabinet
[9] Power SupplyCBA
[4] Inverter PowerCBA
[8] Jack CBA
[18] Speaker(s)
[6] Shield Box [10] PCB Holder
[12] ChassisBracket (L,R)
[7] Digital Main CBA Unit
[15] Junction CBA
[11] Stand Shaft(L,R)
[19] Front Cabinet
[13] LCD Module Assembly
[17] Side Jack CBA
[9]Power Supply CBA
D3D5
8(S-13), *CN204, *CN801, *CN802 ---
[10] PCB Holder D3 4(S-14) ---
[11] Stand Shaft (L, R) D4 4(S-15) ---
[12]Chassis Bracket (L, R)
D4 6(S-16) ---
[13]LCD Module Assembly
D4 13(S-17) ---
[14] Function CBA
D4D5 3(S-18), *CL106B ---
[15] Junction CBA
D4D5 *CL101A ---
[16] IR Sensor CBA
D4D5 2(S-19) ---
[17] Side Jack CBA
D4D5 2(S-20) ---
[18] Speaker(s) D4 8(S-21) ---
[19] Front Cabinet D4 --------------- ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
Step/Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
4-2 A81H1DC
[3] Rear Cabinet
[2] Stand Cover
[1] Stand Base
(S-1)
(S-2)
(S-2)
(S-3)
(S-3)
(S-3)
(S-5)
(S-5)
(S-4)
(S-4)
(S-1)
(S-3)
(S-5)
(S-5)
(S-5)
(S-5)(S-5)
Fig. D1
4-3 A81H1DC
[5] Jack Holder(D)[6] Shield Box
[7] Digital MainCBA Unit
(N-1)
(S-6)
(S-7)
[4] Inverter Power CBA
(S-8)
(S-11)
(S-9)(S-10)
(S-6)
Fig. D2
4-4 A81H1DC
[9] Power Supply CBA
[10] PCB Holder
(S-12)
(S-14)
(S-13)
[8] Jack CBA
(S-13)
(S-13)
(S-14)
(S-14)
(S-14)
Fig. D3
4-5 A81H1DC
[13] LCD ModuleAssembly
[14] Function CBA
[16] IR SensorCBA
[18] Speaker
[19] Front Cabinet
(S-15)
(S-20)
[11] Stand Shaft (L)
[11] Stand Shaft (R)
(S-15)
[12] ChassisBracket (L)
[12] ChassisBracket (R)(S-16)
(S-16)
(S-16)(S-17)
(S-17)
(S-17)
(S-17)(S-17)
(S-17)
(S-17)
(S-18)
(S-19)
[15] JunctionCBA
[17] Side Jack CBA
(S-21)
[18] Speaker
(S-21)
(S-17)
(S-17)
Fig. D4
4-6 A81H1DC
TV Cable Wiring Diagram
CN4201 CN3707
CN3705CN3702CN3601
CN3701
CN501
CN7001
Function CBA
Power SupplyCBA
Digital Main CBA Unit
CL7002B
CN204
Fig. D5
Inverter Power CBA
CL106B
Side JackCBA
Jack CBA
IR Sensor CBA
To Speaker
CL101A
To LCD ModuleAssembly
CN751CN752
CN500CN206
CN200
CN201 CN202 CN203
CN802CN801
CL106A
Junction CBA
CL7002A
CN702CN701 CN753
CN100CL101B
5-1 A81H1EA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. DC Voltmeter
2. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
3. Remote control unit
4. Color Analyzer
How to make the Service remote control unit:Cut “A” portion of the attached remote control unit as shown in Fig. 1.
How to set up the service mode:
Service mode:1. Use the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote control unit. The following screen appears.
Fig. 1A
service button
Ver :Boot SystemPic Ver :
Picture :Submicon Ver :
*********************** Push 0 key Push 0 key********************************************** Push 0 key ******
"*" differs depending on the models.
5-2 A81H1EA
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit, the display changes as follows.
The following adjustment normally are not attempted in the field. Only when replacing the LCD Panel then adjust as a preparation.
2. White Balance AdjustmentPurpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 20 minutes.
2. Input the White Purity.
3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. n] button on the service remote control unit and select “C/D” mode.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
Red mode
Green mode
Blue mode
White mode
[7] button
[7] button
Test Point Adj. Point Mode Input
Screen[CH. o/p]
buttons[VIDEO1]
C/D
White Purity (APL 70%)
or(APL 25%)
M. EQ. Spec.
Pattern Generator, Color analyzer
x= 0.272 ± 0.005y= 0.278 ± 0.005
Figure
Color Analyzer
It carries out in a darkroom.
L = 3 cm
Perpendicularity
INPUT: WHITE 70%, 25%
25%=25IRE 70%=70IRE
INPUT SIGNAL
5-3 A81H1EA
5. [CUTOFF]Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.[DRIVE]Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red Drive adjustment.
6. In each color mode, press [CH. o / p] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y= 0.278 ±0.005).
6-1 A81H1INT
HOW TO INITIALIZE THE LCD TELEVISION
How to initialize the LCD television:1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit. (Refer to page 5-1.)
- To cancel the service mode, press [POWER] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initialzing is complete.
7-1
BLOCK DIAGRAMSSystem Control Block Diagram
A81H1BLS
FU
NC
TIO
N C
BA
IC31
01(S
UB
MIC
RO
CO
NT
RO
LLE
R)
IC33
01IC
3202
(MA
IN M
ICR
O C
ON
TR
OLL
ER
)(M
EM
OR
Y)
CL1
06B
KE
Y-IN
-12
2K
EY
SW
ITC
H
+3.
3V
RE
MO
TE
SE
NS
OR
RS
101
CL1
06A
CL1
01A
KE
Y-IN
-19
9LE
D1
77
LED
26
6R
EM
OT
E2
2
CL1
01B
CN
100
KE
Y-IN
-13
3LE
D1
55
LED
26
6R
EM
OT
E10
10
CN
204
CN
202
LED
16
6LE
D2
55
RE
MO
TE
1616
AM
P-S
TB
Y15
15A
MP
-MU
TE
AM
P-S
TB
YA
MP
-MU
TE
1414
CN
3702
CN
753
22
11
33
CN
206
CN
200
P-O
N-H
214
14BA
CKLI
GHT-A
DJ
BA
CK
LIG
HT-
AD
J
1515
BACK
LIGH
T-SW
BA
CK
LIG
HT-
SW
SC
LS
DA
SC
LS
DA
SC
LS
DA
SC
LS
DA
SC
LS
DA
I2C
-SC
L-A
I2C
-SD
A-A
I2C
-SC
L-B
I2C
-SD
A-B
WP
WP
P-O
N-H
2BA
CKLI
GHT-A
DJBA
CKLI
GHT-S
W
P-O
N-H
2B
AC
KLI
GH
T-A
DJ
BA
CK
LIG
HT-
SW
1313
CN
3701
CN
200
KE
Y-IN
-1
LED
1LE
D2
RE
MO
TE
P-O
N-H
2
BA
CK
LIG
HT-
SW
KE
Y-IN
-16
6C
N37
01
IR S
EN
SO
R C
BA
JUN
CT
ION
C
BA
INV
ER
TE
R P
OW
ER
CB
AP
OW
ER
SU
PP
LY C
BA
DIG
ITA
L M
AIN
CB
A U
NIT
D10
2S
TAN
DB
Y
D10
1P
OW
ER
P-O
N-H
1P
RO
TE
CT
6
P-O
N-H
1P
RO
TE
CT
6
Q34
01LE
V. S
HIF
TE
R
LEV.
SH
IFT
ER
Q34
02
IC33
02
+3.
3V
+3.
3V
RE
SE
T
3 32 31 17 2546 26 12
J1
22 23 15 14
J2 AK24
AK23
D17
B14
A14
V27
V28
V29
W29
W30 B15
A15
6 5 7
IC35
01(V
IDE
O A
DC
)TO
AU
DIO
-1B
LOC
K D
IAG
RA
M
TO A
UD
IO-2
BLO
CK
DIA
GR
AM
AU
DIO
-SW
1
X33
01
54.1
MH
zO
SC
AU
DIO
-SW
2A
UD
IO-S
W3
AU
DIO
-SW
4A
UD
IO-S
W5
AU
DIO
-SW
1A
UD
IO-S
W2
AU
DIO
-SW
3A
UD
IO-S
W4
AU
DIO
-SW
5
X-I
NX
-OU
T
X-I
NX
-OU
T
MA
IN-T
XD
MA
IN-R
XD
SU
B-R
XD
SU
B-T
XD
TO P
OW
ER
SU
PP
LY-1
BLO
CK
DIA
GR
AM
TO A
UD
IO-2
BLO
CK
D
IAG
RA
M
TO P
OW
ER
SU
PP
LY-2
BLO
CK
DIA
GR
AM
37 38
IC38
09(T
ON
E C
ON
TR
OL)
25 26
IC30
01(M
TS
/SA
P A
UD
IO S
IGN
AL
PR
OC
ES
S)
27 24
IC40
02(H
DM
I SW
)
15 14
AE26
AD26
AM
P-M
UT
EAG
25
AH25
AU
DIO
-MU
TE
AU
DIO
-MU
TE
AM
P-S
TB
Y27 41
RE
SE
T
RE
SE
TR
ES
ET
AJ27
35
RE
SE
TR
ES
ET
RE
SE
T
AH26
13
C6
X31
01
4MH
zO
SC
45
IC31
02
RE
SE
T5
419
RE
SE
T
7-2 A81H1BLVIS
Video Input Select Block Diagram
DIG
ITA
L M
AIN
CB
A U
NIT
JAC
K C
BA
SID
E J
AC
K C
BA
IC35
01(V
IDE
O A
DC
)
IC37
01 (
ME
MO
RY
)
VID
EO
SIG
NA
L
CL7
002A
CL7
002B
VID
EO
-IN
25
S-V
IDE
O-C
-IN
21
S-V
IDE
O-Y
-IN
23
5 1 3
CN
3707
CN
7001
VID
EO
-IN
25
S-V
IDE
O-C
-IN
27
S-V
IDE
O-Y
-IN
29
36 34 32V
IDE
O-I
N1
21S
-VID
EO
-C-I
N1
18S
-VID
EO
-Y-I
N1
VID
EO
-IN
2S
-VID
EO
-C-I
N2
S-V
IDE
O-Y
-IN
2V
IDE
O-I
N1
S-V
IDE
O-C
-IN
1S
-VID
EO
-Y-I
N1
19
20 23 22CO
MPO
NENT
-Y-IN
135
COM
PONE
NT-P
b-IN
134
COM
PONE
NT-P
r-IN1
33
6 7 8CO
MPO
NENT
-Y-IN
239
COM
PONE
NT-P
b-IN
240
COM
PONE
NT-P
r-IN2
38
2 1 3
CO
MP
ON
EN
T-Y
-IN
1
CO
MP
ON
EN
T-P
b-IN
1
CO
MP
ON
EN
T-P
r-IN
1
CO
MP
ON
EN
T-Y
-IN
2
CO
MP
ON
EN
T-P
b-IN
2
CO
MP
ON
EN
T-P
r-IN
2
JK70
03
JK70
05
JK75
02V
IDE
O-I
N2
JK75
03S
-VID
EO
-IN
2
CY
JK70
02V
IDE
O-I
N1
MU
X
PC
-V-S
YN
CP
C-H
-SY
NC
DV
I-V
-SY
NC
DV
I-D
ATA
(0-2
3)
TO L
CD
D
RIV
EB
LOC
K
DIA
GR
AM
DV
I-H
-SY
NC
DV
I-C
LOC
K
DV
I-V
-SY
NC
DV
I-H
-SY
NC
DV
I-C
LOC
K
OU
TP
UT
FO
RM
ATT
ING
43-5
0,55
-62,
76-8
3
JK70
01S
-VID
EO
-IN
1C
Y
JK37
01
PC
-IN
PC
-RP
C-G
PC
-BP
C-V
-SY
NC
PC
-H-S
YN
C
SD
AS
CL
9 6 11 25 22 27 20 18 15 14 1371 70 68
1 2 3 14 13 12 15
CLA
MP
AD
CM
UX
CS
C
Q71
02B
UF
FE
R
Q71
04B
UF
FE
R
Q71
03B
UF
FE
R
Q71
01B
UF
FE
R
Q71
05B
UF
FE
R
Q71
06B
UF
FE
R
5 6
WF
6W
F5
WF
4
WF
1W
F3
WF
2
7-3
Audio-1 Block Diagram
A81H1BLA1
DIG
ITA
L M
AIN
CB
A U
NIT
JAC
K C
BA
SID
E J
AC
K C
BA
IC70
01(I
NP
UT
SE
LEC
T)
(IN
PU
T S
ELE
CT
)
SW
CT
L
13
1 2 4 5 12 11
910
SW
CT
L
109
11
ST
ER
EO
FIL
TE
R75
uSD
E-E
MP
H
dBX
DE
-EM
PH
L+R
FIL
TE
R
WID
E B
AN
DF
ILT
ER
WID
E B
AN
DR
MS
DE
TW
IDE
BA
ND
EX
PAN
D
SP
EC
TR
AL
EX
PAN
D
SP
EC
TR
AL
RM
S D
ET
SP
EC
TR
AL
FIL
TE
R
OF
FS
ET
CA
NC
EL
L-C
H
R-C
H
MAT
RIX
AG
CO
FF
SE
TC
AN
CE
LL-
RF
ILT
ER
(L-R
)/S
AP
SW
SA
PF
ILT
ER
SA
PD
EM
OD
SA
P O
UT
FIL
TE
R
AU
DIO
1(L-C
H)
(R-C
H)
213
IC30
01(M
TS
/SA
P A
UD
IO S
IGN
AL
PR
OC
ES
S)
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
2
JK70
06
TU
3001
(TU
NE
R U
NIT
)
SIF
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
2
JK75
02
AU
DIO
(L)
-IN
2
AU
DIO
(R)
-IN
2
OF
FS
ET
CA
NC
EL
JK40
06
HD
MI-
AU
DIO
(L)-
IN
HD
MI-
AU
DIO
(R)-
IN
JK40
05P
C-
AU
DIO
-IN
3
AU
DIO
(L)
-IN
1
JK70
02
AU
DIO
(R)
-IN
1
JK70
04
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
1
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
1
15
CO
MP
1
CO
MP
2
SIF
/BB
SW
INP
UT
VC
AS
IFD
EM
OD
FIL
TE
RC
F30
01
AU
DIO
2
AU
DIO
1
CO
MP
1
CO
MP
2A
UD
IO2
14
AU
DIO
SIG
NA
L
CL7
002B
CL7
002A
99
AU
DIO
(R)-
IN2
77
AU
DIO
(L)-
IN2
CN
7001
AU
DIO
-SW
4A
UD
IO-S
W5
CN
3707
TO
AU
DIO
-2B
LOC
K
DIA
GR
AM
1229
SE
L-A
UD
IO(R
)14
27S
EL-
AU
DIO
(L)
1526
AU
DIO
-SW
516
25A
UD
IO-S
W4
Q70
01
Q70
02
Q38
07Q
3808
Q38
09
12 13 15 1 12 13 15 1
3 3
IC38
02
IC38
01
(IN
PU
T S
ELE
CT
)
SW
CT
L
109
11
AU
DIO
-SW
3
AU
DIO
-SW
1
AU
DIO
(L)
AU
DIO
(R)
AU
DIO
-SW
2
2930
Q30
06B
UF
FE
RQ
3005
BU
FF
ER
TU
NE
RS
EL
PC
HD
MI
TU
NE
RS
EL
PC
HD
MI
BU
FF
ER
Q38
11
BU
FF
ER
Q38
10
WF
7
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
7-4
Audio-2 Block Diagram
A81H1BLA2
DIG
ITA
L M
AIN
CB
A U
NIT
JAC
K C
BA
PO
WE
R S
UP
PLY
CB
A
IC38
03
IC38
03
(OP
AM
P)
IC38
05(O
P A
MP
)
(AU
DIO
AD
C)
IC33
01(D
IGIT
AL
SIG
NA
L P
RO
CE
SS
)
JK70
08
JK70
07
AU
DIO
(L)
-OU
T
AU
DIO
(R)
-OU
T
DIG
ITA
L-A
UD
IO-O
UT
(CO
AX
IAL)
AU
DIO
SIG
NA
L
TO A
UD
IO-1
BLO
CK
D
IAG
RA
M
CN
3702
CN
202
88
AU
DIO
(R)
1010
AU
DIO
(L)
CN
3707
CN
7001
Q80
0
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
DIA
GR
AM
1526
AU
DIO
(R)-
OU
T31
10S
PD
IF-O
UT
1328
AU
DIO
(L)-
OU
T
CN
801
2S
P(L
)-1
SP
(L)+
CN
802
2S
P(R
)-1
SP
(R)+
1
12A
411
3 21
10 15
2
BU
FF
ER
Q38
02
TO
NE
C
ON
TR
OL
AM
P-M
UT
EA
MP
-ST
BY
AU
DIO
AD
C
AU
DIO
DA
CA
UD
IOD
IGIT
AL
SIG
NA
LP
RO
CE
SS
DT
V/H
DM
I-A
UD
IO S
IGN
AL
TO L
CD
DR
IVE
BLO
CK
DIA
GR
AM
5 67
IC38
09
(TO
NE
CO
NT
RO
L)
3 21
5 67
1 2
23 19T
ON
E
CO
NT
RO
L
SP
901
SP
EA
KE
RL-
CH
SP
902
SP
EA
KE
RR
-CH
AU
DIO
(L)
AU
DIO
(R)
A2
A3
D6
AC27
AC28
AB28
AB27
AB29
AB30
AA28
AA27
A5
MU
TE
-ON
Q38
04M
UT
E-O
NQ
3803
Q38
05
AU
DIO
-MU
TE
TO
SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M
DR
IVE
2122
CLN
801
CLN
802
IC80
0 (A
UD
IO P
OW
ER
AM
P)
1 44
9,10
13,1
4
35,3
631
,32
LPF
1P
WM
1D
RIV
ER
1
LPF
2P
WM
2
SH
UT
DO
WN
MU
TE
CO
NT
RO
L
DR
IVE
R2
7-5 A81H1BLLCD
DIG
ITA
L M
AIN
CB
A U
NIT
IC42
01(L
VD
S T
RA
NS
MIT
TE
R)
TU
3001
(T
UN
ER
UN
IT)
TU
-SC
LT
U-S
DA
TU
-SC
LT
U-S
DA
DV
I-V
-SY
NC
DV
I-H
-SY
NC
DV
I-C
LOC
K
DT
V-I
F(+
)D
TV
-IF
(-)
TO V
IDE
OIN
PU
T S
ELE
CT
BLO
CK
DIA
GR
AM
HD
MI-
IN1
HD
MI-
IN2
JK40
02
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LK(+
)T
MD
S-C
LK(-
)D
DC
DAT
AD
DC
CLK
IC32
03 (
FLA
SH
ME
MO
RY
)
IC32
04 (
SD
RA
M)
PLL
TT
LPA
RA
LLE
LTO LV
DS
R D
ATA
(0-7
)
G D
ATA
(0-7
)
B D
ATA
(0-7
)
VID
EO
DE
CO
DE
R/O
SD
AU
DIO
DE
CO
DE
R
DT
V/H
DM
I-A
UD
IO S
IGN
AL
TO A
UD
IO-2
BLO
CK
DIA
GR
AM
DAT
A(0
-7)
DAT
A(0
-7)
DAT
A(0
-15)
DAT
A(0
-15)
AD
DR
ES
S(0
-15)
AD
DR
ES
S(0
-15)
HD
MI
DE
CO
DE
R
SD
AS
CL
DIG
ITA
LS
IGN
AL
PR
OC
ES
S
IC33
01(D
IGIT
AL
SIG
NA
L P
RO
CE
SS
)
IC40
02(H
DM
I SW
)
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
LCD
MO
DU
LE
CN
4201
TX1O
-DAT
A0(+
)7
TX1O
-DAT
A0(-)
6TX
1O-D
ATA1
(+)
9TX
1O-D
ATA1
(-)8
TX1O
-DAT
A2(+
)11
TX1O
-DAT
A2(-)
10TX
1O-D
ATA3
(+)
17TX
1O-D
ATA3
(-)16
TX1O
-CLO
CK(+
)14
TX1O
-CLO
CK(-)
13TX
1E-D
ATA0
(+)
21TX
1E-D
ATA0
(-)20
TX1E
-DAT
A1(+
)23
TX1E
-DAT
A1(-)
22TX
1E-D
ATA2
(+)
25TX
1E-D
ATA2
(-)24
TX1E
-DAT
A3(+
)31
TX1E
-DAT
A3(-)
30TX
1E-C
LOCK
(+)
28TX
1E-C
LOCK
(-)27
36 37 33 34 31 32 26 27 28 29
115455A
10
49 50 46 47 44 45 38 39 41 42
AD
1A
C4
AD
2
AH10
P3
P4
T3
T4
V4
V3
M3
M4
L2 L1
B10
D10
AK20
AK19
21
VID
EO
4 2014 15A
H6
AG
6
AH20
AG15
AJ19
AK21
AG21
AH14
7 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15
JK40
04
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LK(+
)T
MD
S-C
LK(-
)D
DC
DAT
AD
DC
CLK
22 21 25 24 28 27 19 18 31 30
7 8 5 4 1 2 10 11 77 78
62 61 65 64 68 67 59 58 70 71
HD
MI
SW
DE
MO
D.
MAT
RIX
VID
EO
AD
C
VID
EO
-IN
2
DV
I-V
-SY
NC
DV
I-D
ATA
(0-2
3)
DV
I-H
-SY
NC
DV
I-C
LOC
K
DV
I-V
-SY
NC
Y3,
Y4,
AA
1-A
A4,
AB
1-A
B4,
AC
1,A
C2,
AD
3,A
D4,
AE
1-A
E4,
AF
1-A
F4,
AG
1,A
G2
DV
I-H
-SY
NC
DV
I-C
LOC
K
S-V
IDE
O-C
-IN
2S
-VID
EO
-Y-I
N2
VID
EO
-IN
1S
-VID
EO
-C-I
N1
S-V
IDE
O-Y
-IN
1
3-10
1,2,
93-9
6,99
,100
85-9
2
A12
,A13
,B12
,B
13,C
12,C
13,
D12
,D13
A8,
A11
,B9,
B11
,C9,
C11
,D
9,D
11
A6,
A7,
B7,
B8,
C7,
C8,
D7,
D8
29-3
2,41
-44
AG
3,A
H1-
AH
3,A
J1-A
J3,A
K2
G27
,G28
,H27
,H
28,J
27-J
30,
K28
-K30
,L27
,L2
8,M
27-M
29
B1,
B9,
C2,
C8,
D1,
D3,
D7,
D9,
F1,
F9,
G2,
G8,
H1,
H3,
H7,
H9
C27
-C30
,D
27-D
30,
E27
-E30
,F
27-F
30
L1-L
3,M
2,M
3,M
7,M
8,N
2,N
3,N
7,N
8,P
2,P
3,P
7,P
8,R
2
Q30
03B
UF
FE
R
LCD Drive Block Diagram
7-6
Power Supply-1 Block Diagram
A81H1BLP1
F50
08A
/250
VLI
NE
FIL
TE
R
L501
,L50
2A
C60
0A
C C
OR
D
BR
IDG
ER
EC
TIF
IER
CO
NT
INU
EP
OW
ER
SU
PP
LY-2
BLO
CK
DIA
GR
AM
BR
IDG
ER
EC
TIF
IER
D50
0
D51
7 -
D52
0
HO
T
HO
TC
OL
D
CO
LD
IC50
0
IC70
2 (F
EE
DB
AC
K)
IC60
0 (F
EE
DB
AC
K)
IC50
3 (F
EE
DB
AC
K)
IC50
2 (F
EE
DB
AC
K)
IC70
3 (I
SO
LATO
R)
(PF
C)
IC70
1(H
IGH
-VO
LTAG
E R
ESO
NAN
T C
ON
TRO
L)
HIG
H-
VOLT
AGE
RES
ON
ANT
CO
NTR
OL
INV
ER
TE
R P
OW
ER
CB
A
PO
WE
R S
UP
PLY
CB
A
4 3
1 2
4 3
1 2
4 3
1 2
4 3
1 2
IC76
1
+13
V
SH
UN
TR
EG
.
+34
5V1
CN
500
HO
T-G
ND
21 2
INV
+24
V1-
5C
N75
1
GN
D6-
10BA
CKLI
GHT
-SW
12BA
CKLI
GHT
-ADJ
13
AL+
15V
1C
N50
1
CN
701
CN
702
HO
T-G
ND
22 1
T60
1
T70
1
LCD
MO
DU
LE
16912131424 7 6 8
15 1110
Q50
0,Q
501Q
502
Q50
8
Q50
3
POW
ERFA
COTO
RCO
RREC
TIO
N VC
C
(AL+
15V
)
Q50
4
Q50
5Q
506
SW
DR
IVE
Q60
0
Q60
1
SW
SW
CT
L
Q60
2+
15V
RE
G.
351 2
Q70
4
Q70
3S
WVC
C
OV
ER
CU
RR
RE
NT
PR
OT
EC
TOR
Q70
1
Q76
2
Q76
1
SW
Q70
2 SW
6 41611 14 13
1115
6512
P-O
N-H
2
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
BA
CK
LIG
HT-
SW
BA
CK
LIG
HT-
AD
J
8A/2
50V
Q50
9
1 2
4 3
INV
+24
V1-
5C
N75
2
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
500)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
yci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 8
A, 2
50V
fuse
.C
AU
TIO
N !
:
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 8
A, 2
50V
.8A
250
V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
7-7
Power Supply-2 Block Diagram
A81H1BLP2
CO
NT
INU
EP
OW
ER
SU
PP
LY-1
BLO
CK
DIA
GR
AM
HO
TC
OL
D
IC60
0 (F
EE
DB
AC
K)
IC50
3 (F
EE
DB
AC
K)
IC50
2 (F
EE
DB
AC
K)
PO
WE
R S
UP
PLY
CB
AD
IGIT
AL
MA
IN C
BA
UN
IT
INV
ER
TE
R P
OW
ER
CB
A4 3
1 2
4 3
1 2
T60
1
CN
200
131514111024 7 6 8
16 129IC
210,
Q21
0,Q
211,
Q21
2
SW
+12
V
Q24
0,Q
241,
Q24
2,Q
243
SW
+13
V
Q22
0,Q
221,
Q22
2
SW
+5V
Q20
0,Q
201
SW
+6V
IC36
04+
5V R
EG
.
IC36
03+
2.5V
RE
G.
IC36
01+
1.2V
RE
G.
IC36
05+
1.8V
RE
G.
IC36
02
+3.
3V R
EG
.
IC22
0+
3.3V
RE
G.
Q25
0+
9V R
EG
.
IC29
0+
3.3V
RE
G.
IC65
0
Q65
0
SH
UN
TR
EG
.
+6V
99
+3V
1111
CN
202
P-O
N-H
122
22C
N20
3P
RO
TE
CT
623
23
CN
206
CN
753
+13
V+
13V
66
+2.
7V7
7
CN
201
CN
3701
CN
3702
CN
3705
CN
3601
LCD
+12
V21
,22
21,2
2
AL+
3.3V
2020
P-O
N+
6V17
,18
17,1
8
P-O
N+
9V16
16+
3V14
14+
4V12
,13
12,1
3+
2.7V
1010
+6V
88
VT
+33
V4
4
AM
P+
13V
P-O
N+
6V
AL+
3.3V
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
DIA
GR
AM
P-O
N-H
1P
RO
TE
CT
6
VT
+33
VP
-ON
+9V
LCD
+12
V
+5V
+3.
3V
+2.
5V+
1.2V
+1.
8V
P-O
N+
9VP
-ON
+3.
3V
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
1 2
4 3
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
8-1 A81H1_SC
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
8-2 A81H1_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F500) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:
5. How to read converged lines
6. Test Point Information
2 315.0 5.0
Voltage Indicates that the voltage is not consistent here.
Power on mode(Unit: Volt)
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
8-3 A81H1SCP1
Power Supply 1/3 Schematic Diagram
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F500) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 8A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250V
8-4 A81H1SCP2
Power Supply 2/3 Schematic Diagram
CN200
1 02 03 04 05 3.36 3.37 2.68 09 7.010 011 3.212 013 3.514 3.215 3.6
CN201
1 0.9
2 2.7
3 0
4 32.9
5 0
6 12.3
7 0
8 7.0
9 0
10 2.6
11 0
12 3.9
13 3.9
14 3.2
15 0
16 9.1
17 5.6
18 5.6
19 0
20 3.3
21 12.3
22 12.3
23 0
VOLTAGE CHART
Pin No. Voltage
Pin No. Voltage
8-5
Power Supply 3/3 Schematic Diagram
A81H1SCP3
CN202
1 02 03 04 3.35 0.96 3.37 08 ---9 010 ---11 012 3.313 5.114 3.615 0.116 3.317 018 3.619 020 3.621 022 3.123 2.7
CN203
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
10 0
11 0
12 0
13 0
14 0
15 0
16 0
17 0
18 0
19 0
20 0
21 0
22 0
23 3.1
VOLTAGE CHART
Pin No. Voltage
Pin No. Voltage
8-6 A81H1SCJ
Jack & Side Jack Schematic Diagram
CN7001
1 02 3.93 04 05 06 4.07 08 09 010 1.511 012 4.113 014 4.115 016 3.317 018 9.119 020 3.921 2.822 4.023 0
24 0
25 0
26 0
27 0
28 0
29 0
30 0
31 0
32 4.0
33 2.8
34 0
35 0
36 4.0
37 0
38 0
39 0
40 3.8
VOLTAGE CHART
Pin No. Voltage
8-7 A81H1SCINV
Inverter Power Schematic Diagram
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
8-8 A81H1SCF
Function Schematic Diagram
8-9 A81H1SCIR
IR Sensor & Junction Schematic Diagram
8-10 A81H1SCD1
Digital Main 1/9 Schematic Diagram
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-11 A81H1SCD2
Digital Main 2/9 Schematic Diagram
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-12
Digital Main 3/9 Schematic Diagram
A81H1SCD3
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-13
Digital Main 4/9 Schematic Diagram
A81H1SCD4
8-14
Digital Main 5/9 Schematic Diagram
A81H1SCD5
8-15
Digital Main 6/9 Schematic Diagram
A81H1SCD6
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-16
Digital Main 7/9 Schematic Diagram
A81H1SCD7
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-17
Digital Main 8/9 Schematic Diagram
A81H1SCD8
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-18
Digital Main 9/9 Schematic Diagram
A81H1SCD9
The order of pins shown in this diagram is different from that of actual IC3301.IC3301 is divided into seven and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
8-19
Power Supply CBA Top View
BA81H0F01012-1
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F500) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 8A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250V
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
8-20
Power Supply CBA Bottom View
BA81H0F01012-1
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F500) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 8A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.8A 250V
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
8-21 BA81H0F01022-1
Jack CBA Top View
8-22
WF4
WF3
WF2
WF1
WF7
WF6
WF5
PIN 2 OFCN7001PIN 6 OFCN7001
PIN 1 OFCN7001PIN 7 OFCN7001
PIN 3 OFCN7001PIN 8 OFCN7001
PIN 12 OFCN7001PIN 14 OFCN7001
PIN 20 OFCN7001PIN 36 OFCN7001
PIN 22 OFCN7001PIN 32 OFCN7001
PIN 23 OFCN7001PIN 34 OFCN7001
BA81H0F01022-1
Jack CBA Bottom View
8-23
Inverter Power CBA Top View
BA81H0F01022-4
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
8-24
Inverter Power CBA Bottom View
BA81H0F01022-4
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
8-25
Function CBA Top View
Function CBA Bottom View
BA81H0F01012-4
Junction CBA Top & Bottom View
BA81H0F01012-2
8-26
IR Sensor CBA Top View
IR Sensor CBA Bottom View
BA81H0F01012-3
Side Jack CBA Top View
Side Jack CBA Bottom View
BA81H0F01022-3
WAVEFORMS
A81H1WF9-1
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1 ~ WF7 = Waveforms to be observed atWaveform check points.(Shown in Schematic Diagram.)
CVBS 0.2V 20µs
WF1 Pin 20 of CN7001 (CVBS1)Pin 36 of CN7001 (CVBS2)
S-VIDEO-Y 0.2V
WF2 Pin 22 of CN7001 (S1-Y)Pin 32 of CN7001 (S2-Y)
20µs
S-VIDEO-C 0.2V
WF3 Pin 23 of CN7001 (S1-C)Pin 34 of CN7001 (S2-C)
20µs AUDIO 1V 0.5ms
WF7 Pin 14 of CN7001 (JACK-SEL-L)Pin 12 of CN7001 (JACK-SEL-R)
VIDEO-Pr 0.2V 20µs
Pin 8 of CN7001 (COMP1-Pr)Pin 3 of CN7001 (COMP2-Pr)
WF6
VIDEO-Pb 0.2V 20µs
Pin 7 of CN7001 (COMP1-Pb)Pin 1 of CN7001 (COMP2-Pb)
WF5
VIDEO-Y 0.2V 20µs
Pin 6 of CN7001 (COMP1-Y)Pin 2 of CN7001 (COMP2-Y)
WF4
WIRING DIAGRAM
A81H1WI10-1
CN
4201 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23 24 25
TX1O
-DAT
A2(+
)TX
1O-D
ATA2
(-)
NU
NU
NU
NU
NU
TX1O
-DAT
A0(-)
TX1O
-DAT
A0(+
)TX
1O-D
ATA1
(-)TX
1O-D
ATA1
(+)
TX1O
-CLO
CK(-)
TX1O
-CLO
CK(+
)G
ND
TX1O
-DAT
A3(-)
TX1O
-DAT
A3(+
)N
UN
UTX
1E-D
ATA0
(-)TX
1E-D
ATA0
(+)
TX1E
-DAT
A1(-)
TX1E
-DAT
A1(+
)TX
1E-D
ATA2
(-)TX
1E-D
ATA2
(+)
GN
D
282726 29 30 3231 3433 3635 37 38 39 40
GN
D
TX1E
-CLO
CK(+
)G
ND
TX1E
-DAT
A3(-)
TX1E
-DAT
A3(+
)V
-CO
MN
UG
ND
GN
DG
ND
GN
DLC
D+
12V
LCD
+12
VLC
D+
12V
41LC
D+
12V
TX1E
-CLO
CK(-)
CN
7001 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23 24 25
GN
DS
PD
IF-O
UT
COMP
ONEN
T-Pb-I
N2CO
MPON
ENT-Y
-IN2
COMP
ONEN
T-Pr-IN
2G
ND
GN
DCO
MPON
ENT-Y
-IN1
COMP
ONEN
T-Pb-I
N1CO
MPON
ENT-P
r-IN1
GN
D
GN
DSE
L-AU
DIO(
L)A
UD
IO-S
W5
AU
DIO
-SW
4P
-ON
+9V
P-O
N+
9VG
ND
VID
EO
-IN
1S-
VIDE
O-SW
-IN1
S-VI
DEO-
Y-IN
1S-
VIDE
O-C-
IN1
GN
DG
ND
SEL-
AUDI
O(R)
282726 29 30 3231 3433 3635 37 38 39 40
CN
3707
CN
751
40 3839 3637 3435 33 32
CN
753 1 32 54 76 8 9
BACK
LIG
HT-A
DJP
-ON
-H2
BACK
LIG
HT-S
WP
RO
TE
CT
3PR
OTE
CT1(
NU)
+13
VN
UG
ND
GN
D
CN
206
1 32
CN
701 1 2
+34
5VH
OT-
GN
D
CN
500
1 2C
N70
2 1 2H
OT-
GN
DA
L+15
V
CN
501
2 154 76 8 9
31 282930 27
CL7
002B
1 32 54 76 8 9 10 131211 14
NU
GN
D
S-VI
DEO
-C-IN
2S-
VIDE
O-S
W-IN
2S-
VIDE
O-Y
-IN2
GN
DV
IDE
O-I
N2
GN
DAU
DIO
(L)-I
N2G
ND
AUDI
O(R
)-IN2
NU
NU
NU
1 32 54 76 8 9 10 131211 14
NU
GN
D
INV
+24
VIN
V+
24V
INV
+24
VIN
V+
24V
INV
+24
VG
ND
GN
DG
ND
GN
D
BACK
LIGH
T-ADJ
NU
BACK
LIGH
T-SW
CL7
002A
SID
E
JAC
K
CB
A
INV
ER
TE
RP
OW
ER
CB
A JAC
K
CB
A
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PL
Y C
BA
JUN
CT
ION
CB
A
LC
DM
OD
UL
E
1 32 54 76 8 9 10 131211 14
26 2425 2223 2021 19 18
CN
202 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23
GN
DA
UD
IO(L
)
GN
DN
UN
ULE
D3(
NU
)LE
D2
LED
1G
ND
AU
DIO
(R)
GN
D
NU
AM
P-M
UT
EA
MP
-ST
BY
RE
MO
TE
GN
DN
UG
ND
NU
GN
DP
-ON
-H1
PR
OT
EC
T3
NU
CN
3702
1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23C
N20
3 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23
GN
DN
U
GN
DN
UG
ND
GN
DG
ND
NU
GN
DN
UG
ND
GN
DN
UG
ND
NU
GN
DN
UN
UN
UN
UN
UP
RO
TE
CT
6
NU
CN
3705
1 32 54 76 8 9 10 131211 14 15
CN
3701
CN
204
CN
100
CL1
01B
CL1
01A
1 32 54 76 8 9 10 131211 14 15
+3V
GN
D
NU
NU
NU
GN
DN
UK
EY-
IN1
+2.
7VG
ND
+6V
BACK
LIGH
T-SW
P-O
N-H
2BA
CKLI
GHT-A
DJ
GN
D
CN
200
1 32 54 76 8 9 10 131211 14 15
1716 1918 2120 22 23
CN
3601 1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23
GN
D+
2.7V
PR
OT
EC
T2
PR
OT
EC
T1
1 2S
P(L
)+S
P(L
)-
1 2S
P(R
)+S
P(R
)-
GN
DV
T+
33V
GN
DLC
D-1
2V(N
U)
GN
D+
6VG
ND
+4V
+3V
GN
DP
-ON
+9V
P-O
N+
6VP
-ON
+6V
GN
DA
L+3.
3VLC
D+
12V
LCD
+12
VG
ND
+4V
CN
201
1 32 54 76
CN
801
CN
802
8 9 10 131211
11
910
78
56
4321GND
REMOTE
GNDNUKEY-IN1NULED1LED2NUNUAL+3.3V
11
910
78
56
4321
CL1
06A
CL1
06B
1
32
4
AL+3.3VKEY-IN1NUGND
1
32
4
1
32
54
76
891011GND
REMOTE
GNDNUKEY-IN1NULED1LED2NUNUAL+3.3V
1
32
54
76
89
1011
14 15 1716 1918 2120 22 23
17 16 131415 12 11 910 78 56 4 3 2 1
AUDI
O(R)
-OUT
AUDI
O(L)
-OUT
GN
DN
UG
ND
S-VI
DEO-
Y-IN
2S-
VIDE
O-SW
-IN2
S-VI
DEO-
C-IN
2G
ND
VID
EO
-IN
2G
ND
NU
NU
NU
GN
D
FU
NC
TIO
N C
BA
IR S
EN
SO
R C
BA
AU
DIO
(R)
-IN
1
AU
DIO
(L)
-OU
T
AU
DIO
(R)
-OU
T
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
1
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
1
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
2
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
2
S-V
IDE
O-I
N2
VID
EO
-IN
2
AU
DIO
(L)
-IN
2
AU
DIO
(R)
-IN
2
VID
EO
-IN
1
SP
901
SP
EA
KE
RL-
CH
SP
902
SP
EA
KE
RR
-CH
AU
DIO
(L)
-IN
1
DIG
ITA
L-A
UD
IO-O
UT
S-V
IDE
O-I
N1
CO
MP
ON
EN
T-Y
-IN
1
CO
MP
ON
EN
T-P
b-IN
1
CO
MP
ON
EN
T-P
r-IN
1
CO
MP
ON
EN
T-Y
-IN
2
CO
MP
ON
EN
T-P
b-IN
2
CO
MP
ON
EN
T-P
r-IN
2C
LN80
1
CLN
802
CN
752
1 32 54 76 8 9 10G
ND
INV
+24
VIN
V+
24V
INV
+24
VIN
V+
24V
INV
+24
VG
ND
GN
DG
ND
GN
D
AC
600
AC
CO
RD
TU
3001
TU
NE
R U
NIT
D-S
UB
CO
NN
EC
TO
RH
DM
I-C
ON
NE
CT
OR
-1H
DM
I-C
ON
NE
CT
OR
-2
11-1 A81H1CEX
EXPLODED VIEWS
Cabinet
L12
A1
B1
L19
A4
A12
L6
L6
A6
L6
A9
A21
A22
B2
L6
L2
L2
L2
L2
L2L6
B8
B4
L11L4
B5
L7
L3
L3
B7
A10
See Electrical Parts List for parts with this mark.
Digital MainCBA Unit
Inverter PowerCBA
AC600
L4
L4
L3
L11
IR SensorCBA
Side Jack CBA
Function CBA
SP901
CLN801
SP902
CLN802
Power Supply CBA
A3
A11
L4
B20
L11
A13
A7
L5
L4
L15
B3
A12
L3
L3
L2
B22
CLN420Jack CBA
L8
L3
L1
L9
L1
L9
LCD-1
B16
B17
B6
B9
S5
A23
L1
L1
L11L11
L11
L11
L12
B19 B18L12
L12
L12
L12 B18B17
L12
L3
L3
L20
L20
L2
L6 A12
A12
L4
B7
L3CLN751
CLN752
CLN501
CLN370
Digital MainCBA Unit Parts
B23
L1
L1
JunctionCBA
11-2 A81H1PEX
Packing
X2
X9
X3
X4
L6
Tape
Tape
X5
X1S12
S2
Packing Tape
Packing Tape
PP Band
Packing Tape
Packing Tape
LCD Unit Assembly
Stand Assembly
Packing Tape
S4
S13
S6
S5
S3
Some Ref. Numbers are not in sequence.
FRONT
S3
20070911 12-1 A81H1CA
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref. No. Description Part No.
A1 FRONT CABINET A81H1UH 1EM021813
A3 CONTROL PLATE A81H0UH 1EM322723
A4 REAR CABINET A81H1UH 1EM021814
A6# RATING LABEL A81H1UH ----------
A7 FUNCTION KNOB A81H0UH 1EM121947
A9 STAND COVER A81H0UH 1EM021739
A10 REAR COVER A7260JH 1EM322484
A11 LED LENS A7260JH 1EM221523
A12 STAND RUBBER FOOT L5001CB 1EM423855
A13 SENSOR LENS A7260JH 1EM221522
A21 POP LABEL A81H1UH ----------
A22 PUNCHING SHEET A81H0UH 1EM021740
A23 ENERGY STAR LABEL A81H0UH ----------
B1 CHASSIS BRACKET(L) A81H0UH 1EM121905
B2 CHASSIS BRACKET(R) A81H0UH 1EM121906
B3 SHIELD BOX A81H0UH 1EM122153
B4 PCB HOLDER A81H0UH 1EM121904
B5 JACK HOLDER(D) A81H1UH 1EM221636
B6 JACK HOLDER(S) A81H0UH 1EM221578
B7 STAND BASE A81H0UH 1EM221581
B8 STAND SHAFT(L) A81H0UH 1EM221579
B9 STAND SHAFT(R) A81H0UH 1EM221580
B20 GASKET A71F0UH 1EM424393
B22 GRAND TAPE A81H0UH 1EM425137
B23 GRAND TAPE (TR-19) A71F0UH 1EM424512
CLN370 WIRE ASSEMBLY 101 40PIN UL2896 WX1A81H0-101
CLN420 WIRE ASSEMBLY 201 36PIN AWG32 WX1A81H0-201
CLN501 WIRE ASSEMBLY 302 2PIN AWG24 WX1A81H0-302
CLN751 WIRE ASSEMBLY 304 14PIN AWG24 WX1A81H0-304
CLN752 WIRE ASSEMBLY 305 10PIN AWG24 WX1A81H0-305
CLN801 WIRE ASSEMBLY 306 2PIN AWG22 WX1A81H0-306
CLN802 WIRE ASSEMBLY 307 2PIN AWG22 WX1A81H0-307
L1 ASSEMBLY SCREW A81H0UH 1EM424524
L2 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140
L3 SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080
L4 SCREW P-TIGHT M3X10 BIND HEAD+ GBJP3100
L5 SCREW P-TIGHT M3*10 WASHERHEAD+ GCJP3100
L6 DOUBLE SEMS SCREW M4X10 + BLK FPH34100
L7 SCREW B-TIGHT 3X10 BIND HEAD+ BLK GBHB3100
L8 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080
L9 DOUBLE SEMS SCREW M5X10 BLACK M5X10
FPH35100
L11 SCREW SEMS M4X8 PAN HEAD + FPJ34080
L15 NUT 3/8-32UNEF 0EM401451A
L19 HEX SCREW #4-40 7MM 1EM422042
L20 SCREW S-TIGHT 3X8 WASHER HEAD+BLAC GCHS3080
LCD-1 LCD 42V TFT LC420WU5-SLA2 UDPULCDGS003
SP901 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
SP902 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
PACKINGS2 STYROFORM TOP A81H0UH 1EM021800
S3 STYROFORM BOTTOM A81H0UH 1EM021801
S4 SET BAG A81H0UH 1EM322766
S5 SERIAL NO. LABEL L9750UA ----------
S6 STAND BAG A81H0UH 1EM424649
S12 CARTON(U) A81H1UH 1EM322741
S13 CARTON(L) A81H0UH 1EM322725
ACCESSORIESX1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
X2# OWNERS MANUAL A81H1UH 1EMN22312
X3 REMOTE CONTROL NF020UD NF020UD NF020UD
X4 DRY BATTERY(SUNRISE) R6SSE/2S XB0M451MS002
X5 SCREW BAG A81N0UH 1EM424596
X9 QUICK SETUP GUIDE A81H1UH 1EMN22313
Ref. No. Description Part No.
20070911 13-1 A81H1EL
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Compatibility between the DIGITAL MAIN CBAUNIT and the POWER SUPPLY CBAFor both DIGITAL MAIN CBA UNIT and POWER SUPPLYCBA, two different types of connecters, either Type A(SerialNumber below 'J37713000') or Type B(Serial Number over'J37713001'), are being used for this model.Consequently, there are pairing compatibilities betweenType A and Type B when repairing these units. Refer to thecorrelation table below and make sure to confirm the serialnumber of the unit.
DIGITAL MAIN CBA UNIT
MMA CBA
POWER SUPPLY CBAC.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
TYPEDIGITAL
MAIN CBA UNIT
POWER SUPPLY CBA
Part No.(CN201, CN202,
CN203)
SERIAL NUMBER
A 1ESA14707 1ESA14710 J3TWA23TG001 below J37713000
B 1ESA20892 1ESA20888 JCTWA23TG004 over J37713001
Type A
Type B
POWER SUPPLY CBA (1ESA14710)
CN201 CN202 CN203
DIGITAL MAIN CBA UNIT (1ESA14707)
CN3601 CN3702 CN3705
POWER SUPPLY CBA (1ESA20888)
CN201 CN202 CN203
DIGITAL MAIN CBA UNIT (1ESA20892)
CN3601 CN3702 CN3705
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT 1ESA14707 or1ESA20892
Ref. No. Description Part No.
MMA CBAConsists of the following:
1ESA14710 or1ESA20888
POWER SUPPLY CBAFUNCTION CBAIR SENSOR CBAJUNCTION CBA
----------------------------------------
Ref. No. Description Part No.
POWER SUPPLY CBAConsists of the following:
----------
CAPACITORSC203 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C204 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102
C205 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C210 CERAMIC CAP.(AX) F Z 0.01µF/25V CCA1EZTFZ103
C211 ELECTROLYTIC CAP. 1000µF/16V M CE1CMASDL102
C220 ELECTROLYTIC CAP. 220µF/25V M CE1EMASDL221
C221 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C231 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C250 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C251 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C290 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C292 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C293 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C294 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C295 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C296 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C297 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C298 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C299 CAP ELE STD-85 4700µF 6.3V SL CE0KMZNDL472
C300 CAP ELE STD-85 4700µF 6.3V SL CE0KMZNDL472
C301 ELECTROLYTIC CAP. 2200µF/16V M CE1CMZNDL222
C500 ELECTROLYTIC CAPACITOR 100µF/400V CA2H101NC230
C501# CERAMIC CAP. B K 2200pF/500V CCD2JKP0B222
C502# METALIZED FILM CAP. 1µF/630V K CT2K105DT037
C503 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C504 CERAMIC CAP.(AX) B K 0.1µF/50V CA1J104TU011
C505 CERAMIC CAP.(AX) B K 0.022µF/50V CA1J223TU011
C507 ELECTROLYTIC CAP. 22µF/25V M CE1EMASDL220
C508 CERAMIC CAP.(AX) F Z 0.01µF/25V CCA1EZTFZ103
C509 CERAMIC CAP.(AX) CH J 680pF/50V CA1J681TU008
C510# TF CAP. 1µF/50V CT1J105MS045
C511 CERAMIC CAP(AX) CH J 33pF/50V CA1J330TU008
C512 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C513 CERAMIC CAP.(AX) F Z 0.01µF/25V CCA1EZTFZ103
C515 CERAMIC CAP. B K 0.01µF/500V CCD2JKP0B103
C517 CERAMIC CAP. B K 0.01µF/500V CCD2JKP0B103
C518# METALIZED FILM CAP. 0.22µF/250V CT2E224MS037
C519# METALIZED FILM CAP. 0.22µF/250V CT2E224MS037
C520# METALIZED FILM CAP. 1µF/250V CT2E105MS037
C523 SAFETY CAP. 1000pF/250V KX CA2E102MR050
C524 CERAMIC CAP. BN 680pF/2KV CCD3DKA0B681
20070911 13-2 A81H1EL
C525 CERAMIC CAP.(AX) B K 1000pF/50V CCA1JKT0B102
C526 SAFETY CAP. 1000pF/250V KX CA2E102MR050
C527 SAFETY CAP. 1000pF/250V KX CA2E102MR050
C528 SAFETY CAP. 2200pF/250V KX CA2E222MR050
C529 METALIZED FILM CAP. 0.1µF/250V CT2E104MS037
C530 CERAMIC CAP.(AX) B K 0.01µF/50V CA1J103TU011
C531 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C532 CERAMIC CAP. B K 2200pF/500V CCD2JKP0B222
C600 CERAMIC CAP. BN 1000pF/2KV CCD3DKA0B102
C603 STACKED FILM CAP. 0. 0.15µF/50V J CMA1JJS00154
C604 FILM CAP.(P) 0.033µF/50V J CMA1JJS00333
C605 CAP METALIZED FILM 2.2µF 50V CT1J225MS045
C606 CERAMIC CAP.(AX) F Z 0.01µF/25V CCA1EZTFZ103
C607 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
C608 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C609# PP CAP. 0.0033µF/1.6KV J CT3C332MS039
C610 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101
C653 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C654 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C655 ELECTROLYTIC CAP. 100µF/50V M CE1JMASDL101
C656 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C657 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C658 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C659 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C664 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C668 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C669 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C671 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C674 PCB JUMPER D0.6-P5.0 JW5.0T
C675 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C800 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C801 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C802 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C803 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C804 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C805 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3
C806 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C807 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C808 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C809 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C811 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C812 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C813 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C814 CERAMIC CAP.(AX) B K 0.1µF/50V CA1J104TU011
C815 CERAMIC CAP.(AX) B K 0.1µF/50V CA1J104TU011
C817 CHIP CERAMIC CAP.(2125) B K 4.7µF/16V CHE1CK30B475
C818 CERAMIC CAP.(AX) B K 0.1µF/50V CA1J104TU011
C819 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C820 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C821 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C822 CERAMIC CAP.(AX) B K 0.1µF/50V CA1J104TU011
C823 CHIP CERAMIC CAP.(2125) B K 4.7µF/16V CHE1CK30B475
C826 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C827 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C828 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C829 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C830 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
CONNECTORSCN200 CONNECTOR PRINT MES C/15/S/
127301115K2JCTWA15TG004
CN201 CONNECTOR 23P Refer to page 13-1
CN202 CONNECTOR 23P Refer to page 13-1
Ref. No. Description Part No.
CN203 CONNECTOR 23P Refer to page 13-1
CN204 242 SERIES CONNECTOR 224202111W1 J322C11TG001
CN206 TWG CONNECTOR 09P TWG-P09P-A1 J3TWA09TG001
CN500 WIRE ASSEMBLY 303 2PIN AWG18 WX1A81H0-303
CN501 CONNECTOR PRINT OSU 008283021200000S+
J383C02UG004
CN801 CONNECTOR BASE 2P(EH) B 2B-EH-A(LF)(SN)
J3EHC02JG010
CN802 CONNECTOR BASE 2P(EH) B 2B-EH-A(LF)(SN)
J3EHC02JG010
DIODESD110 ZENER DIODE MTZJT-7710B QDTB00MTZJ10
D200 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D201 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1
D202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D220 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
D221 PCB JUMPER D0.6-P10.0 JW10.0T
D222 ZENER DIODE MTZJT-7715B QDTB00MTZJ15
D223 DIODE FR104-B NDLZ000FR104
D224 ZENER DIODE MTZJT-773.9B QDTB0MTZJ3R9
D225 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D227 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D231 ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D233 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D240 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D241 ZENER DIODE MTZJT-7716B QDTB00MTZJ16
D243 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D250 ZENER DIODE MTZJT-7710B QDTB00MTZJ10
D251 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D291 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D500# DIODE BRIDGE D10XB60-7000 QDWZ0D10XB60
D503# ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D504 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D505 DIODE 1N5406 NDLZ001N5406
D506# FAST RECOVERY DIODE YG972S6R QDLZYG972S6R
D507 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D508# ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D509 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D510 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D511 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D512 ZENER DIODE MTZJT-7724B QDTB00MTZJ24
D514 RECTIFIER DIODE 1N4005 NDQZ001N4005
D516 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D517 RECTIFIER DIODE 1N4005 NDQZ001N4005
D518 RECTIFIER DIODE 1N4005 NDQZ001N4005
D519 RECTIFIER DIODE 1N4005 NDQZ001N4005
D520 RECTIFIER DIODE 1N4005 NDQZ001N4005
D521 ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D522 ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D523 ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D550 PCB JUMPER D0.6-P5.0 JW5.0T
D600 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D601 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D602 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D604 DIODE FR104-B NDLZ000FR104
D606 ZENER DIODE MTZJT-7715B QDTB00MTZJ15
D607 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D608# DIODE 05NU42 QDTZ005NU42Q
D609 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
D610 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D611 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D612 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D614 ZENER DIODE MTZJT-7736B QDTB00MTZJ36
Ref. No. Description Part No.
20070911 13-3 A81H1EL
D615 ZENER DIODE MTZJT-7720B QDTB00MTZJ20
D616 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D650 SCHOTTKY BARRIER DIODE ERC84-009 QDLZERC84009
D651 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D652 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D654 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D655 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D659 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D661 CHIP ZENER DIODE CMZ22(TE12L Q) QD1Z00CMZ22Q
D664 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D665 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D666 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D667 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D668 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D669 DIODE 1N5406 NDLZ001N5406
D670 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D671 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D672 SCHOTTKY BARRIER DIODE ERC84-009 QDLZERC84009
D673 DIODE FR104-B NDLZ000FR104
D674 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D675 SCHOTTKY BARRIER DIODE ERC81-004 QDPZERC81004
D676 PCB JUMPER D0.6-P20.0 JW20.0T
D678 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D680 CHIP ZENER DIODE CRZ47(TE85L Q) QD1Z00CRZ47Q
ICSIC210 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
IC220 IC LD1117V NSZBA0SSS046
IC290 REGULATOR IC(3.5V) PQ035ZN1HZPH QSZBA0TSH078
IC500# IC PFC UC2853ADTR SOIC 8 NSZBA0TTY257
IC502# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC503# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC600# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC650# IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
IC800 IC POWER AMP BD5422EFS-E2 QSZBA0TRM113
COILSL290 CHOKE COIL 22µH-K LLBD00PKV021
L501# FILTER LLBG00ZY2015 LLBG00ZY2015
L502# FILTER LLBG00ZY2015 LLBG00ZY2015
L503 CIOL TOROIDAL HKBS-14D100-9810WRPF LLET0Z0BF003
L800 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L801 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L802 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L803 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L804 INDUCTOR 22µH-K-5FT LLARKBSTU220
TRANSISTORSQ200 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q201 PNP TRANSISTOR POWER 2SA1887(F) QQWZ2SA1887F
Q210 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q211 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q212 TRANSISTOR(PB FREE) KTC2026-Y/P NQEYKTC2026P
Q220 TRANSISTOR(PB FREE) KTC2026-Y/P NQEYKTC2026P
Q221 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q222 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q240 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q241 PNP TRANSISTOR POWER 2SA1887(F) QQWZ2SA1887F
Q242 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q243 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q250 TRANSISTOR 2SD400(E) QQUE002SD400
Q500# TRANSISTOR KTD1347-C-AT/P NQSCKTD1347P
Q501 TRANSISTOR KTB985-C-AT/P NQSC0KTB985P
Q502# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
Q503# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
Ref. No. Description Part No.
Q504# TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F
Q505 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q506 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q508 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q509 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q600# MOS FET 2SK3798(Q) QFWZ2SK3798Q
Q601# TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q602 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q650 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q800 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
RESISTORSR204 METAL OXIDE FILM RES. 2W J 1 Ω RN021R0DP004
R205 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R206 CARBON RES. 1/4W J 330 Ω RCX4JATZ0331
R207 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R208 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R209 CHIP RES. 1/10W F 680 Ω RRXAFR5H6800
R210 CHIP RES. 1/10W F 560 Ω RRXAFR5H5600
R211 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R212 CARBON RES. 1/4W J 15k Ω RCX4JATZ0153
R213 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R214 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R215 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R216 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182
R217 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R218 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R219 CHIP RES. 1/10W F 8.2k Ω RRXAFR5H8201
R220 RES METALIZED FILM T 1/4W F 1.00k Ω RDC1001HH003
R221 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R222 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R223 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R224 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R225 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R226 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R227 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R233 CARBON RES. 1/4W J 820 Ω RCX4JATZ0821
R234 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R235 CARBON RES. 1/4W J 27k Ω RCX4JATZ0273
R236 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R237 METAL OXIDE FILM RES. 2W J 1 Ω RN021R0DP004
R240 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R241 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R242 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R243 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R244 METAL OXIDE FILM RES. 2W J 0.27 Ω RN02R27DP004
R245 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R246 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R247 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151
R248 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151
R249 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R250 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R251 METAL OXIDE FILM RES. 1W J 3.9 Ω RN013R9DP003
R253 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R254 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682
R255 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R256 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R257 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R292 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R293 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R294 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R500# RES CEMENT 5W J 0.33 Ω RW05R33KA050
R501# RES CEMENT 5W J 0.39 Ω RW05R39KA050
Ref. No. Description Part No.
20070911 13-4 A81H1EL
R502 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R503 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R504 CARBON RES. 1/4W J 56k Ω RCX4JATZ0563
R506 CARBON RES. 1/4W J 22 Ω RCX4JATZ0220
R507 CARBON RES. 1/4W J 15 Ω RCX4JATZ0150
R508 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R509 CARBON RES. 1/4W J 15 Ω RCX4JATZ0150
R510 CARBON RES. 1/4W J 22 Ω RCX4JATZ0220
R512 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R513 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R514 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R515 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R516 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R517 CARBON RES. 1/4W J 10 Ω RCX4JATZ0100
R518 CARBON RES. 1/4W J 10 Ω RCX4JATZ0100
R519 CARBON RES. 1/4W J 27k Ω RCX4JATZ0273
R520 CARBON RES. 1/4W J 56k Ω RCX4JATZ0563
R521 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R522 RES METALIZED FILM T 1/4W F 3.92k Ω RDC3921HH003
R523 PCB JUMPER D0.6-P5.0 JW5.0T
R524 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R525 RES METALIZED FILM T 1/4W F 100k Ω RDC1003HH003
R526 RES METALIZED FILM T 1/4W F 100k Ω RDC1003HH003
R527 RES METALIZED FILM T 1/4W F 100k Ω RDC1003HH003
R528 RES METALIZED FILM T 1/4W F 27.4k Ω RDC2742HH003
R529 PCB JUMPER D0.6-P5.0 JW5.0T
R530 RES METALIZED FILM 1/4W F 274k Ω RDC2743HH001
R531 RES METALIZED FILM 1/4W F 274k Ω RDC2743HH001
R532 RES METALIZED FILM 1/4W F 332k Ω RDC3323HH001
R533 RES METALIZED FILM 1/4W F 274k Ω RDC2743HH001
R534 RES METALIZED FILM T 1/4W F 10.0k Ω RDC1002HH003
R537 RES METALIZED FILM T 1/4W F 100k Ω RDC1003HH003
R539 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R540 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R541 CARBON RES. 1/4W J 2.2 Ω RCX4JATZ02R2
R542 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R543 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R544# SOLID RES.(UL) 1/2W 3.3M Ω RSX2335KE010
R545 SOLID RES.(UL) 1/2W 8.2M Ω RSX2825KE010
R546 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R547 CARBON RES. 1/4W J 27k Ω RCX4JATZ0273
R548 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R549 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R550 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R551 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R553 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R558 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R559 CARBON RES. 1/4W J 47k Ω RCX4JATZ0473
R600 RES CEMENT 5W J 1.0 Ω RW051R0KA050
R603 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151
R604 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R605 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R606 CARBON RES. 1/4W J 470k Ω RCX4JATZ0474
R607 CARBON RES. 1/4W J 470k Ω RCX4JATZ0474
R608 CARBON RES. 1/4W J 470k Ω RCX4JATZ0474
R609 CARBON RES. 1/4W J 470k Ω RCX4JATZ0474
R610 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R611 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471
R612 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R613 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R614 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R615 METAL OXIDE FILM RES. 1W J 10 Ω RN01100DP003
R616 METAL OXIDE FILM RES. 2W J 100k Ω RN02104DP004
Ref. No. Description Part No.
R617 METAL OXIDE FILM RES. 2W J 100k Ω RN02104DP004
R650 RES METALIZED FILM T 1/4W F 2.21k Ω RDC2211HH003
R651 RES METALIZED FILM T 1/4W F 1.00k Ω RDC1001HH003
R652 RES METALIZED FILM T 1/4W F 332 Ω RDC3320HH003
R653 RES METALIZED FILM T 1/4W F 2.21k Ω RDC2211HH003
R654 RES METALIZED FILM T 1/4W F 2.21k Ω RDC2211HH003
R655 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R656 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R657 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R662 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R663 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R665 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R666 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R672 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R673 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R674 CARBON RES. 1/4W J 39k Ω RCX4JATZ0393
R800 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003
R801 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394
R802 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R803 CHIP RES. 1/10W F 51.0 k Ω RRXAFR5H5102
R804 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R805 CHIP RES. 1/10W F 51.0 k Ω RRXAFR5H5102
R807 CHIP RES. 1/10W J 270k Ω RRXAJR5Z0274
R808 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003
R809 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R810 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R811 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
MISCELLANEOUSAC600# AC CORD LP-11W&PT218P-K90A&S WAC0172LW020
B16 HEAT SINK EAI ASSEMBLY A81H0UH 1EM424642
B17 HEAT SINK EAJ ASSEMBLY A81H0UH 1EM424644
B18 HEAT SINK EAK ASSEMBLY A81H0UH 1EM424646
B19 HEAT SINK EAL ASSEMBLY A81H0UH 1EM424648
BC502 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC503 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC504 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC505 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC506 PCB JUMPER D0.6-P5.0 JW5.0T
BC507 PCB JUMPER D0.6-P5.0 JW5.0T
BC508 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC509 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC600 PCB JUMPER D0.6-P5.0 JW5.0T
BC601 PCB JUMPER D0.6-P5.0 JW5.0T
BC602 PCB JUMPER D0.6-P5.0 JW5.0T
BC603 PCB JUMPER D0.6-P5.0 JW5.0T
F500# FUSE 8A/250V(PB FREE) 0215008.MXP PBGZ20BAG022
FC600 CORE FERRITE TOROIDAL HF40T18X10X10 XL04018TE001
FH500 HOLDER FUSE CNT41-0014 1790424
FH501 HOLDER FUSE CNT41-0014 1790424
J115 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
JS211 PCB JUMPER D0.6-P5.0 JW5.0T
JP200 PCB JUMPER D0.6-P5.0 JW5.0T
JP201 PCB JUMPER D0.6-P25.0 JW25.0T
JP202 PCB JUMPER D0.6-P10.0 JW10.0T
JP212 PCB JUMPER D0.6-P5.0 JW5.0T
JP511 PCB JUMPER D0.6-P5.0 JW5.0T
JP600 PCB JUMPER D0.6-P7.5 JW7.5T
JP601 PCB JUMPER D0.6-P7.5 JW7.5T
JP801 PCB JUMPER D0.6-P12.5 JW12.5T
L12 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
SA500# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
SA502 SURGE ABSORBER 470V+-10PER NVQZ10D471KB
Ref. No. Description Part No.
20070911 13-5 A81H1EL
FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
JACK ASSEMBLY
JACK CBA
SA503 SURGE ABSORBER RA-452MS-V7-Y PDVAEA0DC452
SA504 PCB JUMPER D0.6-P7.5 JW7.5T
T600# TRANS POWER 7736 LTT3PC0KT033
TM601 EYELET TYPE D-1 0VM406868
TM602 EYELET TYPE D-1 0VM406868
TP500 PCB JUMPER D0.6-P10.0 JW10.0T
TP501 PCB JUMPER D0.6-P10.0 JW10.0T
TP650 PCB JUMPER D0.6-P10.0 JW10.0T
Ref. No. Description Part No.
FUNCTION CBAConsists of the following:
----------
CAPACITORSC118 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C119 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
RESISTORSR120 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R121 PCB JUMPER D0.6-P5.0 JW5.0T
R124 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152
R125 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152
R126 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R127 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R128 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R129 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
SWITCHESSW101 TACT SWITCH SKQSAB SST0101AL038
SW102 TACT SWITCH SKQSAB SST0101AL038
SW103 TACT SWITCH SKQSAB SST0101AL038
SW104 TACT SWITCH SKQSAB SST0101AL038
SW105 TACT SWITCH SKQSAB SST0101AL038
SW106 TACT SWITCH SKQSAB SST0101AL038
SW107 TACT SWITCH SKQSAB SST0101AL038
MISCELLANEOUSBC102 PCB JUMPER D0.6-P5.0 JW5.0T
Ref. No. Description Part No.
IR SENSOR CBAConsists of the following:
----------
CAPACITORSC102 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C103 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C105 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C107 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMASSL470
DIODESD101 LED 333GT/E NPHZ00333GTE
D102 LED L-53HT NP4Z000L53HT
RESISTORSR107 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100
R108 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R109 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R110 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R111 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R112 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R113 PCB JUMPER D0.6-P5.0 JW5.0T
MISCELLANEOUSBC100 PCB JUMPER D0.6-P5.0 JW5.0T
CL101 WIRE ASSEMBLY 003 11PIN AWG26 WX1A81H0-003
CL106 WIRE ASSEMBLY 004 4PIN AWG26 WX1A81H0-004
Ref. No. Description Part No.
RS101 PHOTO LINK MODULE KSM-712TH2E USESJRSKK044
Ref. No. Description Part No.
JUNCTION CBAConsists of the following:
----------
CONNECTORCN100 242 SERIES CONNECTOR TUC-P11X-B1 WHT
STJCTUB11TG002
Ref. No. Description Part No.
JACK ASSEMBLYConsists of the following:
1ESA14714
JACK CBAINVERTER POWER CBASIDE JACK CBA
------------------------------
Ref. No. Description Part No.
JACK CBAConsists of the following:
----------
CAPACITORSC7001 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMASSL101
C7002 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7003 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMASSL101
C7040 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7041 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7042 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7043 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7044 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7045 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7046 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7047 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7048 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7049 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7050 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7051 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7052 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7053 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7054 CHIP CERAMIC CAP. CH J 12pF/50V CHD1JJ3CH120
C7055 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMASSL470
C7056 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7061 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7062 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7063 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7064 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7065 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7066 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7091 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
C7092 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221
C7093 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
C7094 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221
C7101 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7102 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7103 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMASSL4R7
C7104 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7105 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7106 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7107 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7108 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7201 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
Ref. No. Description Part No.
20070911 13-6 A81H1EL
C7202 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
C7203 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
C7204 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
C7205 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
C7206 ELECTROLYTIC CAP. 47µF/10V M H7 CE1AMASSL470
C7211 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7213 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7215 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7216 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
CONNECTORCN7001 FMN CONNECTOR TOP 40P 40FMN-BTRK-
A(LF)(SN)JCFNG40JG020
DIODESD7001 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D7002 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
ICIC7001 IC SWITCHING TC4052BF(ELNF) QSZBA0TTS162
TRANSISTORSQ7001 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7002 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7101 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7102 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7103 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7104 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7105 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q7106 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
RESISTORSR7000 PCB JUMPER D0.6-P5.0 JW5.0T
R7001 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7002 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7003 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R7004 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R7005 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7006 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7007 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7008 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7009 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7010 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7011 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7012 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7013 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R7014 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7015 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R7016 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7017 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7018 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7019 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7020 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7021 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7022 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7031 PCB JUMPER D0.6-P5.0 JW5.0T
R7032 PCB JUMPER D0.6-P5.0 JW5.0T
R7040 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7041 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7043 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7044 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7047 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7048 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7049 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7051 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7052 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7053 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
Ref. No. Description Part No.
R7054 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7055 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7056 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R7057 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7058 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7059 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7061 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7062 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7063 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7064 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7065 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7066 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7067 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7068 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7069 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7071 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7072 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7081 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7082 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7083 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7084 PCB JUMPER D0.6-P5.0 JW5.0T
R7085 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7086 PCB JUMPER D0.6-P5.0 JW5.0T
R7087 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7091 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7093 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7094 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7096 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R7101 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R7102 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7103 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7104 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7105 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7106 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7107 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R7108 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243
R7113 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7201 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7202 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7203 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7204 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R7206 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7207 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7208 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7209 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R7211 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7212 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7213 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7214 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R7216 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7217 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7218 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7219 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R7221 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7222 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7223 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7224 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
R7226 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681
R7227 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
R7228 CHIP RES. 1/10W J 39k Ω RRXAJR5Z0393
R7229 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333
MISCELLANEOUS
Ref. No. Description Part No.
20070911 13-7 A81H1EL
INVERTER POWER CBA
CL7002 WIRE ASSEMBLY 005 14PIN AWG26 WX1A81H0-005
JK7001 JACK SW DIN PCB S YKF51-5379V JYEJ040JC002
JK7002 JACK SW RCA PCB S RCA-347HDT-02 JYRJ030YUQ01
JK7003 JACK RCA PCB S 03 RCA-347HT-03 JXRJ030YUQ01
JK7004 JACK SW RCA PCB S RCA-228H(2)NI-01 JYRJ020YUQ02
JK7005 JACK RCA PCB S 03 RCA-347HT-03 JXRJ030YUQ01
JK7006 JACK SW RCA PCB S RCA-228H(2)NI-01 JYRJ020YUQ02
JK7007 JACK RCA PCB S AV-4B-70HH JXRJ010SNJ06
JK7008 JACK SW RCA PCB S RCA-228H(2)NI-01 JYRJ020YUQ02
JS7002 PCB JUMPER D0.6-P7.5 JW7.5T
Ref. No. Description Part No.
INVERTER POWER CBAConsists of the following:
----------
CAPACITORSC701 ELECTROLYTIC CAPACITOR 150µF/400V CA2H151NC229
C703 CAP METALIZED FILM 2.2µF 50V CT1J225MS045
C706 FILM CAP. 0.33µF/50V J CMA1JJS00334
C707 CERAMIC CAP.(AX) CH J 470pF/50V CA1J471TU008
C709 FILM CAP.(P) 0.01µF/50V J CMA1JJS00103
C710 FILM CAP. 0.33µF/50V J CMA1JJS00334
C711 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C712 CERAMIC CAP. B K 220pF/500V CCD2JKP0B221
C713 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C714 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C715 P.P.CAPACITOR 0.022µF/630V J CT2K223MS086
C717 FILM CAP.(P) 0.0047µF/50V J CMA1JJS00472
C718 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C731 SAFETY CAP. 1000pF/250V KX CA2E102MR050
C751 CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C752 CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C753 CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C754 CERAMIC CAP.(AX) F Z 0.1µF/50V CCA1JZTFZ104
C755 CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C761 MYLAR CAP. 0.22µF/50V J CMA1JJS00224
C763 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C764 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C786 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
CONNECTORSCN701 CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001
CN702 CONNECTOR PRINT OSU 008283021200000S+
J383C02UG004
CN751 CONNECTOR PRINT OSU B14B-PH-K-S(LF)(SN)
J3PHC14JG029
CN752 PH CONNECTOR TOP 10P B10B-PH-K-S(LF)(SN)
J3PHC10JG029
CN753 BOARD CONNECTOR 09P(PB FREE) 127301109K2
JCTWA09TG004
DIODESD703 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D704 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D705 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D706 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D711 CHIP ZENER DIODE CRZ27(TE85L Q) QD1Z00CRZ27Q
D712 CHIP ZENER DIODE CRZ36(TE85L Q) QD1Z00CRZ36Q
D751 DIODE SCHOTTKY YG802C10R QDQZYG802C10
D752 DIODE SCHOTTKY YG802C10R QDQZYG802C10
D756 CHIP ZENER DIODE CRZ30(TE85L Q) QD1Z00CRZ30Q
D757 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D758 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D781 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
ICS
Ref. No. Description Part No.
IC701# IC HIGH-VOLTAGE RESONANT CONTR L6599N
NSZBA0SSS312
IC702# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC703# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC761 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
TRANSISTORSQ701# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
Q702# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
Q703 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q761 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q762 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
RESISTORSR701 RES MATALIZED FILM 1/4W F 562k Ω RDC5623HH001
R702 RES MATALIZED FILM 1/4W F 562k Ω RDC5623HH001
R703 RES MATALIZED FILM 1/4W F 562k Ω RDC5623HH001
R704 RES MATALIZED FILM 1/4W F 562k Ω RDC5623HH001
R705 CARBON RES. 1/4W J 10 Ω RCX4JATZ0100
R706 RES METALIZED FILM T 1/4W F 12.1k Ω RDC1212HH003
R707 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R708 RES METALIZED FILM T 1/4W F 15.0k Ω RDC1502HH003
R709 CARBON RES. 1/4W J 39 Ω RCX4JATZ0390
R712 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R713 CARBON RES. 1/4W J 1M Ω RCX4JATZ0105
R714 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R715 RES METALIZED FILM T 1/4W F 75.0 Ω RDC75R0HH003
R718 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R719 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R720 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R721 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R722 CARBON RES. 1/4W J 39 Ω RCX4JATZ0390
R723 CARBON RES. 1/4W J 39 Ω RCX4JATZ0390
R724 CARBON RES. 1/4W J 39 Ω RCX4JATZ0390
R725 CARBON RES. 1/4W J 56 Ω RCX4JATZ0560
R726 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R727 CARBON RES. 1/4W J 56 Ω RCX4JATZ0560
R728 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R753 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R754 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R760 CARBON RES. 1/4W J 5.6k Ω RCX4JATZ0562
R761 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R762 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R763 PCB JUMPER D0.6-P5.0 JW5.0T
R764 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R765 RES METALIZED FILM T 1/4W F 9.09k Ω RDC9091HH003
R766 PCB JUMPER D0.6-P5.0 JW5.0T
R767 RES METALIZED FILM T 1/4W F 2.21k Ω RDC2211HH003
R768 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R769 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R770 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R771 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R772 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R773 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R784 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R785 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R787 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
MISCELLANEOUSB17 HEAT SINK EAJ ASSEMBLY A81H0UH 1EM424644
B18 HEAT SINK EAK ASSEMBLY A81H0UH 1EM424646
BC701 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC781 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC782 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC783 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
Ref. No. Description Part No.
20070911 13-8 A81H1EL
SIDE JACK CBA
BC784 BEAD INDUCTOR FBR07HA121TB-00 LLBF00ZTU021
BC785 PCB JUMPER D0.6-P5.0 JW5.0T
L12 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
T701# TRANS POWER ETS42LZ196AD LTT4PC0MS004
Ref. No. Description Part No.
SIDE JACK CBAConsists of the following:
----------
RESISTORSR7501 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7502 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7503 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
MISCELLANEOUSJK7502 JACK SW RCA PCB S RCA-347HDT-02 JYRJ030YUQ01
JK7503 JACK SW DIN PCB S YKF51-5379V JYEJ040JC002
Ref. No. Description Part No.