+ All Categories
Home > Documents > T1S-000092_rev2 (MM Formated)

T1S-000092_rev2 (MM Formated)

Date post: 03-Jun-2018
Category:
Upload: mohamedramy
View: 223 times
Download: 0 times
Share this document with a friend

of 96

Transcript
  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    1/96

    9 Elementary procedures of mobility management

    The tests are based on TS 24.008.

    In this clause, when the expected sequence require that "a mobile originated ! connection is attempted", it shall beor a ser#ice other than emergenc$ call.

    In this clause, a initial ! message is either a S%T&' message, a (%)IST%( message or a '*+T message -inthat case the acnowledged mode o operation on S'I / will ha#e be established and this message will be sent onS'I /.

    9.1 TMSI reallocation

    The intention o the T!SI (eallocation procedure is to assign a new temporar$ identit$ or the &%. I the message isnot understood b$ the &%, the networ could not establish a lin to the &%. s this is a common !! procedure, it canbe initiated at an$ time.

    9.1.1 Conformance requirement

    1 &ser %quipment shall acnowledge a new T!SI when explicitl$ allocated during a location updatingprocedure or an incoming call.

    2 The T!SI shall be updated on the SI! when the &ser %quipment is correctl$ deacti#ated in accordance withthe manuacturers instructions.

    / &ser %quipment shall answer paging with this T!SI and includes it in the 'aging (esponse message.

    Reference(s

    TS 24.008 lause 4./.1.

    9.1.! Test purpose

    To #eri$ that the &% is able to recei#e and acnowledge a new T!SI b$ means o an explicit T!SI reallocationprocedure.

    To #eri$ that the &% has stored the T!SI in a non*#olatile memor$.

    The implicit reallocation procedure is tested in clause 3.4.1.

    9.1." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5, belonging to dierent location areas a and b, deault parameters.

    * &ser %quipment

    * the &% has #alid T!SI -6 T!SI1, 7S, 7c. It is "idle updated" on cell 5.

    Related ICS$I%IT statement(s

    Switch o button 9es:o.

    ;a$ to bring the &% into ser#ice.

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    2/96

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI -6 T!SI1, 7S, 7c. It is "idle updated" on cell .

    Test rocedure

    The &% is paged in cell 5 and the securit$ mode is established. n explicit T!SI reallocation procedure is perormed.The ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    3/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1

    SS I-ITITE/ RRCC0--ECTI0-

    Mobile identity 2 TMSI1.

    Establis#ment Cause3 ns*er to paging.

    ! 4I-4 RES0-SE" SEC'RIT5 M0/E C0MM-/ T#e SS starts decip#ering.6 SEC'RIT5 M0/E C0M7ETE T#e SS starts encip#ering.8 TMSI RE770CTI0-

    C0MM-/Mobile identity 2 ne* TMSI (TMSI! different fromTMSI 1.

    TMSI RE770CTI0-C0M7ETE

    : RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    4/96

    9.! ut#entication

    The purpose o this procedure is to #eri$ the user identit$. correct response is essential to guarantee theestablishment o the connection. I not, the connection will drop.

    The SS shall be able to handle #ectors o 7c, (+, and S(%S in a similar wa$ as the !S:5SS entities. The SS

    shall incorporate a test algorithm or generating S(%S and 7c rom (+ and 7i which operates as described inannex 4.

    9.!.1 ut#entication accepted

    9.!.1.1 Conformance requirement

    1 &ser %quipment shall correctl$ respond to an uthentication (equest message b$ sending an uthentication(esponse message with the S(%S inormation ield set to the same #alue as the one produced b$ theauthentication algorithm in the networ.

    2 &ser %quipment shall indicate in a 'aging (esponse message the ciphering e$ sequence number which wasallocated to it through the authentication procedure.

    Reference(s

    TS 24.008 lause 4./.2a.

    9.!.1.! Test purpose

    1 To chec that a &ser %quipment correctl$ responds to an uthentication (equest message b$ sending anuthentication (esponse message with the S(%S inormation ield set to the same #alue as the one produced b$the authentication algorithm in the networ.

    2 To chec that a &ser %quipment indicates in a 'aging (esponse message the ciphering e$ sequence numberwhich was allocated to it through the authentication procedure.

    9.!.1." Met#od of test

    Initial conditions

    * S$stem Simulator

    * 1 cell, deault parameters.

    * &ser %quipment

    * the &% has #alid T!SI, 7S -7S1, 7c. It is "idle updated" on the cell.

    Related ICS$I%IT statement(s

    one.

    &oreseen final state of t#e 'E

    The &% has #alid T!SI, 7S and 7c. It is "idle updated" on the cell.

    Test rocedure

    The &% is paged. ter the &% has sent a ')I) (%S'

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    5/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1

    SS I-ITITE/ RRCC0--ECTI0-

    Establis#ment Cause3 ns*er to paging.

    ! 4I-4 RES0-SE C@S- 2 C@S-1" 'TAE-TICTI0- RE?'EST T#e SS initiates aut#entication *it# C@S-! different

    from [email protected] 'TAE-TICTI0- RES0-SE ut#. parameter SRES IE s#all be bit e)act *it# t#e

    +alue as produced by t#e aut#entication algorit#m.8 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    6/96

    9.!.!.! Test purpose

    1 To chec that ,ater reception o an uthentication (e>ect message, the &ser %quipment

    1.1 does not perorm normal location updating?

    1.2 does not perorm periodic location updating?

    1./ does not respond to paging with T!SI?

    1.4 re>ects an$ request rom ! entit$ or !! connection except or emergenc$ call?

    1.@ does not perorm I!SI detach i deacti#ated.

    2 To chec that, ater reception o an uthentication (e>ect message the &ser %quipment, i it supports speech,accepts a request or an emergenc$ call b$ sending a ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    7/96

    E)pected sequence

    3GPP

    7

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    8/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+ed on cell ,

    1

    SS I-ITITE/ RRCC0--ECTI0-

    Establis#ment Cause3 ns*er to paging.

    ! 4I-4 RES0-SE Cip#ering 'TAE-TICTI0- RE?'EST C@S- 2 C@S-1."1 'TAE-TICTI0- RES0-SE"! 70CTI0- '/TI-4 CCET Mobile Identity 2 TMSI.

    ""

    TMSI RE770CTI0-C0M7ETE"6 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    3GPP

    8

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    9/96

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    10/96

    Test rocedure

    The SS requests identit$ inormation rom the &%

    * I!SI in non S%&(IT9 mode?

    * allocated T!SI in non S%&(IT9 mode?

    * I!%I in S%&(IT9 mode.

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1

    SS I-ITITE/ RRCC0--ECTI0-

    Establis#ment Cause3 ns*er to paging.

    ! 4I-4 RES0-SE" I/E-TIT5 RE?'EST Identity type IE is IMSI.

    6 I/E-TIT5 RES0-SE Mobile identity IE specifies t#e IMSI of t#e 'E.8 I/E-TIT5 RE?'EST Identity type IE is TMSI. I/E-TIT5 RES0-SE Mobile identity IE specifies t#e allocated TMSI of t#e

    'E.: SEC'RIT5 M0/E C0MM-/= SEC'RIT5 M0/E C0M7ETE9 I/E-TIT5 RE?'EST Identity type IE is IMEI.1> I/E-TIT5 RES0-SE Mobile identity IE specifies t#e IMEI stored in t#e

    Mobile Equipment.11 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    11/96

    * I!%I in non securit$ mode?

    * I!%ISB in non securit$ mode.

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1

    SS I-ITITE/ RRCC0--ECTI0-

    Establis#ment Cause3 ns*er to paging.

    ! 4I-4 RES0-SE" I/E-TIT5 RE?'EST Identity type IE is IMEI.6 I/E-TIT5 RES0-SE Mobile identity IE specifies t#e IMEI of t#e 'E.8 I/E-TIT5 RE?'EST Identity type IE is IMEIS. I/E-TIT5 RES0-SE Mobile identity IE specifies t#e IMEISD of t#e 'E.: RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    12/96

    9.".!." Met#od of test

    Initial conditions

    * S$stem Simulator

    * 1 cell, deault #alues?* I!SI attach:detach bit set to "1".

    * &ser %quipment

    * the &% has no #alid T!SI?

    * it is "idle updated"?

    * the I!SI has the #alue 0010112/4.

    Related ICS$I%IT statement(s

    The &% is switched on or powered on. The &% perorms I!SI attach. The &% shall include the correct I!SI in theC

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    13/96

    E)pected sequence

    3GPP

    13

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    14/96

    Step Direction Message Comments

    UE SS

    1

    SS I-ITITE/ RRCC0--ECTI0-

    mobile identity 1 contains IMSI of 'E.

    Establis#ment cause3 ns*er to paging.

    ! 4I-4 RES0-SE mobile identity contains t#e IMSI of t#e 'E." I/E-TIT5 RE?'EST identity type IE is IMSI.6 I/E-TIT5 RES0-SE mobile identity IE contains t#e IMSI of t#e 'E.8 T#e call is establis#ed using t#e sequence of t#e

    generic terminating call setup procedure. SS T#e SS stops sending +alid SCCA frames.: RRC C0--ECTI0- RE?'EST= RRC C0--ECTI0- SET'9 CM REEST,7ISAME-T

    RE?'ESTmobile identity IE contains IMSI of t#e 'E.

    1> TMSI RE770CTI0-C0MM-/

    mobile identity contains a TMSI.

    11 TMSI RE770CTI0-C0M7ETE

    1! RRC C0--ECTI0- RE7ESE fter sending t#is message; t#e SS *aits for t#edisconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    15/96

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    16/96

    Eor the networ response three dierent cases are identiied

    1.1 T!SI is allocated?

    1.2 location updating accept contains neither T!SI nor I!SI?

    1./ location updating accept contains I!SI.

    9.6.1." Met#od of test

    9.6.1.".1 7ocation 'pdating$accepted$test1

    Initial conditions3

    * S$stem Simulator

    * two cells, and 5, belonging to dierent location areas with location area identiication a and b o the same'C!?

    * I!SI attach:detach is allowed in both cells?

    * the T/212 time*out #alue is 1:10 hour in both cells.

    * &ser %quipment

    * the &% has a #alid T!SI -6T!SI1 and 7S -67S1. It is "idle updated" on cell .

    Related ICS$I%IT statement(s

    one.

    &oreseen final state of t#e 'E

    The &% has no #alid T!SI. It has #alid 7S and 7c. It is "idle, updated" on cell 5.

    Test rocedure

    The &% is made to select cell 5. normal location updating with T!SI reallocation is perormed in cell 5. The ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    17/96

    E)pected sequence

    3GPP

    17

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    18/96

    Step Direction Message Comments

    UE SS

    1 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell,.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 C@S-1;location area identification 2 a; mobile stationclassmar< 1 as gi+en by t#e ICSand mobile identity 2TMSI1.

    8 70CTI0- '/TI-4 CCET Mobile identity 2 ne* TMSI (2TMSI!; 7I 2 b. TMSI RE770CTI0-

    C0M7ETE: RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    19/96

    !9 4I-4 RES0-SE Mobile identity IE contains t#e IMSI."> RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    20/96

    E)pected sequence

    3GPP

    20

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    21/96

    Step Direction Message Comments

    UE SS

    1 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell,.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 C@S-1;location area identification 2 a; mobile stationclassmar< 1 as gi+en by t#e ICSand mobile identity 2TMSI1.

    8 70CTI0- '/TI-4 CCET Mobile identity 2 ne* TMSI (2TMSI!; 7I 2 b. TMSI RE770CTI0-

    C0M7ETE: RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    22/96

    !9 4I-4 RES0-SE Mobile identity IE contains t#e IMSI."> RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling linects a location updating rom the &ser %quipment with the cause "I!SI unnown in =C(","Illegal &%" or "Illegal !%" the &ser %quipment shall

    1.1 not perorm normal location updating?

    1.2 not perorm periodic location updating?

    1./ not respond to paging with I!SI?

    1.4 not respond to paging with T!SI?

    1.@ re>ect an$ request rom ! entit$ or !! connection other than or emergenc$ call?

    1.H not perorm I!SI detach i it is switched o or has its power source remo#ed.

    2 I the networ re>ects a location updating rom the &ser %quipment with the cause "I!SI unnown in =C(",

    "Illegal &%" or "Illegal !%" the &ser %quipment, i it supports speech, shall accept a request or an emergenc$call b$ sending a (( ects the location updating o the &% with the cause "I!SI unnownin =C(", "illegal &%" or "Illegal !%".

    9.6.!.1." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5, belonging to dierent location areas o the same 'C!?

    * I!SI attach:detach is allowed in both cells?

    * the T/212 time*out #alue is 1:10 hour in both cells.

    * &ser %quipment

    3GPP

    22

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    23/96

    * the &% has #alid T!SI, 7S and 7c. It is "idle updated" on cell .

    Related ICS$I%IT statement(s

    SI! remo#al possible while the &% is powered 9es:o.

    Switch o on button 9es:o.

    Support or speech 9es:o.

    &oreseen final state of t#e 'E

    The &% has #alid T!SI, 7S and 7c. It is "idle updated" on cell .

    Test rocedure

    The SS re>ects a normal location updating with the cause #alue "I!SI unnown in =C(". The ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    24/96

    E)pected sequence

    The sequence is executed or execution counter 6 1, 2, /.

    3GPP

    24

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    25/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell,.

    !

    RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause IE is IMSI un

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    26/96

    !9 'TAE-TICTI0- RE?'EST C@S- 2 C@S-1."> 'TAE-TICTI0- RES0-SE"1 70CTI0- '/TI-4 CCET Mobile Identity 2 TMSI."! TMSI RE770CTI0-

    C0M7ETE"" RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling linect a location updating rom the &ser %quipment with the cause "'C! not allowed" the &ser%quipment shall

    1.1 not perorm periodic updating?

    1.2 not perorm I!SI detach when switched o?

    1./ not perorm I!SI attach when switched on in the same location area?

    1.4 not perorm normal location updating when in the same 'C! and when that 'C! is not selectedmanuall$?

    1.@ re>ect an$ request rom ! entit$ or !! connection other than or emergenc$ call.

    2 I the networ re>ects a location updating rom the &ser %quipment with the cause "'C! not allowed" the&ser %quipment shall

    2.1 perorm normal location updating when a new 'C! is entered?

    2.2 accept a request or an emergenc$ call, i it supports speech, b$ sending a ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    27/96

    * two cells and 5, belonging to dierent location areas a and b and belonging to 'C!2. 'C!2 isdierent rom ='C! and rom 'C!1?

    * I!SI attach:detach is allowed in cells and 5 but not in cell ?

    * the T/212 time*out #alue is 1:10 hour in cells and 5.

    * &ser %quipment

    * the &% has a #alid T!SI. It is "idle updated" on cell ?

    * the &% is in manual mode or 'C! selection.

    Related ICS$I%IT statement(s

    SI! remo#al possible while the &% is powered 9es:o.

    Switch o on button 9es:o.

    The &% is automaticall$ in automatic mode ater switch on 9es:o.

    Support or speech 9es:o.

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI. It is "idle updated" on cell . The &% is in automatic mode or 'C! selection.

    Test rocedure

    The SS re>ects a normal location updating with the cause #alue "'C! not allowed". The ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    28/96

    E)pected sequence

    3GPP

    28

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    29/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1 'E T#e 'E is s*itc#ed off (or po*er is remo+ed.! SS T#e SS acti+ates cells and , and deacti+ates cell C.

    Cell , #as a le+el #ig#er by at least 8 d, t#an cell ." 'E T#e 'E is s*itc#ed on. (or po*er is reapplied If

    necessary t#e 'E is put in manual selection mode. T#e'E s#all offer t#e ne* 7M- as a+ailable to t#e user.T#e 7M- is manually selected.

    6 SS RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.8 RRC C0--ECTI0- SET' 70CTI0- '/TI-4

    RE?'EST: 70CTI0- '/TI-4 REECT ReBect cause 2 7M- not allo*ed.= RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 'E T#e 'E s#all not initiate an RRC connectionestablis#ment on cell or on cell ,.

    11 'E If possible (see ICS SIM detac#ment is performed.0t#er*ise if possible (see ICS s*itc# off is performed.0t#er*ise t#e po*er is remo+ed.

    1! 'E T#e 'E s#all not initiate an RRC connectionestablis#ment on cell or on cell ,. T#is is c#ec RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating."1 RRC C0--ECTI0- SET'"! 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    30/96

    "8 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling linection was recei#ed is manuall$ selected and the SS checs that a normallocation updating is perormed.

    3GPP

    30

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    31/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1 'E T#e 'E is s*itc#ed off (or po*er is remo+ed.! SS T#e SS acti+ates cells and , and deacti+ates cell C.

    Cell , #as a le+el #ig#er by at least 8 d, t#an cell ." 'E T#e 'E is s*itc#ed on (or po*er is reapplied."a 'E If t#e 'E is in manual mode; it s#all offer t#e ne* 7M-

    as a+ailable to t#e user. In t#is case t#e 7M- ismanually selected.

    6 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.8 RRC C0--ECTI0- SET' 70CTI0- '/TI-4

    RE?'EST: 70CTI0- '/TI-4 REECT ReBect cause 2 7M- not allo*ed.= RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.11 RRC C0--ECTI0- SET'1! 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    32/96

    2 I the networ re>ects a location updating rom the &ser %quipment with the cause "Cocation rea not allowed"the &ser %quipment shall

    2.1 perorm normal location updating when a new location area is entered?

    2.2 accept a request or an emergenc$ call, i it supports speech, b$ sending a ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    33/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1 SS T#e R& le+el of cell is lo*ered so t#at cell , isselected; *#ile .

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause 2 7ocation rea not allo*ed. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e mainsignalling lin 70CTI0- '/TI-4

    RE?'EST"1 'TAE-TICTI0- RE?'EST"! 'TAE-TICTI0- RES0-SE"" 70CTI0- '/TI-4 CCET Mobile identity 2 TMSI."6 TMSI RE770CTI0-

    C0M7ETE

    "8 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    34/96

    Specific message contents

    one.

    9.6.!.6 7ocation updating $ reBected $ roaming not allo*ed in t#is location area

    9.6.!.6.1 Conformance requirement

    1 I the networ re>ects a location updating rom the &ser %quipment with the cause "(oaming not allowed inthis area" the &ser %quipment shall

    1.1 not perorm periodic updating?

    1.2 not respond to paging with T!SI?

    1./ re>ect an$ request rom ! entit$ or !! connection other than or emergenc$ call?

    1.4 not perorm I!SI detach.

    2 I the networ re>ects a location updating rom the &ser %quipment with the cause "(oaming not allowed in

    this area" the &ser %quipment shall

    2.1 perorm normal location updating when a new location area is entered?

    2.2 accept a request or an emergenc$ call, i it supports speech, b$ sending a ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    35/96

    Test purpose 8

    To test that i the SI! is remo#ed the list o "orbidden location areas or roaming" is cleared.

    9.6.!.6." Met#od of test

    Initial conditions

    The initial conditions shall be met beore each o the dierent procedures.

    * S$stem Simulator

    * or procedures 1, 2, / and @ Two cells and 5, belonging to dierent location areas o the same 'C!with CI a and b. The ! o that 'C! is the same as that o the ='C!. The ! o that 'C! isdierent rom that o the ='C!?

    * or procedure 4 three cells , 5, o the same 'C! which is not the ='C! with / dierent locationarea codes. ells should dier in signal strength b$ 10 d5 with cell being the strongest and cell theweaest. There should be a 20 d5 range between and . should be set to a le#el o * 40 d5m?

    * I!SI attach:detach is allowed in e#er$ cell?

    * the T/212 time*out #alue is 1:10 hour in e#er$ cell.

    * &ser %quipment

    * procedures 1, 2, / and @ The &% has #alid T!SI, 7S and 7c. It is "idle updated" on cell 5?

    * procedure 4 The &% has #alid T!SI, 7S and 7c. It is "idle updated" on cell ?

    * the list o "orbidden location areas or roaming" shall be empt$ -this ma$ be achie#ed b$ either remo#ingthe SI! or switching the &%

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    36/96

    * The SS re>ects a normal location updating with the cause #alue "(oaming not allowed in this area". The ((ects a normal location updating with the cause #alue "(oaming not allowed in this area". The ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    37/96

    rocedure 1

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell .

    1 SS T#e R& le+el of cell , is lo*ered until cell , is no more

    suitable and t#e 'E selects cell .! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause IE is Roaming not allo*ed in t#is

    location area. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 'E /epending on *#at #as been performed in step 9 t#e 'Eis broug#t bac< to operation and placed in a automaticmode.

    11 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.1! RRC C0--ECTI0- SET'1" 70CTI0- '/TI-4

    RE?'EST7ocation 'pdating Type 2 normal.

    16 70CTI0- '/TI-4 CCET IE Mobile Identity not present.18 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    38/96

    rocedure !

    Step Direction Message Comments

    T#e follo*ing messages are sent and s#all be recei+edon cell .

    1 SS T#e R& le+el of cell , is lo*ered until t#e 'E selects cell. T#e le+el of cell , s#all be suc# t#at cell , is suitable

    for cell selection.! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating T#is message

    is sent on cell ." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause IE is Roaming not allo*ed in t#is

    location area. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 70CTI0- '/TI-4 REECT ReBect cause IE is Roaming not allo*ed in t#is

    location area.11 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin CM SERDICE CCET!1 EMER4E-C5 SET'!! RE7ESE C0M7ETE Cause 2 unassigned number.!" RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    39/96

    rocedure "

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell

    1 SS T#e R& le+el of cell , is lo*ered until t#e 'E selects cell. T#e le+el of cell , s#all be suc# t#at cell , is suitablefor cell selection.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause IE is Roaming not allo*ed in t#is

    location area. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    40/96

    Step Direction Message Comments

    UE SS

    location area.68 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    41/96

    rocedure 8

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell .

    1 SS T#e R& le+el of cell , is lo*ered until cell , is no longersuitable and t#e 'E selects cell .

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 REECT ReBect cause IE is Roaming not allo*ed in t#is

    location area. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    42/96

    9.6.".1." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5 o the same 'C!, belonging to dierent location areas with CI a and b?* the (E power le#el o cell 5 is higher than the one o cell ?

    * I!SI attach:detach is not allowed in both cells?

    * the T/212 time*out #alue is set to ininite in both cells.

    * &ser %quipment

    * the &% has a #alid T!SI, 7S and 7c. It is "Idle updated" on cell 5.

    Related ICS$I%IT statement(s

    one.

    &oreseen final state of t#e 'E

    The &% is "Idle updated" on cell .

    Test rocedure

    The SS causes a random access ailure in the &% during a normal location updating procedure. ter the expir$ oT/21/ and when the cell reselection procedure is inished the &% will tr$ to restart the normal location updatingprocedure.

    The test is repeated but the original cause o the location updating procedure has disappeared. The SS then checs thatthe &% will not restart the location updating procedure.

    3GPP

    42

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    43/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell .

    1 'E T#e R& le+el of cell , is lo*ered until t#e 'E selects cell. T#e R& le+el of cell , is set sufficiently lo* to ensuret#at cell , is not suitable as defined in 4SM >8.>=subclause ..!..

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating. T#is messageis sent by t#e 'E (Ma)HRetrans 1 times.

    " SS T#e SS *aits for 6 seconds.6 'E T#e 'E s#all not send any layer " message during t#is

    time.8 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating. T#e time

    difference bet*een t#is message and t#e last RRCC0--ECTI0- RE?'EST sent in step ! s#all be in t#erange 6 s 9 s.

    RRC C0--ECTI0- SET': 70CTI0- '/TI-4

    RE?'EST

    location updating type 2 normal; C@S- 2 initial +alue;

    7I 2 b; mobile station classmar< 1 and mobile identity 2TMSI.= 70CTI0- '/TI-4 CCET 0ptional IE Mobile Identity not included9 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin SS T#e R& le+el of cell , is set to t#e same +alue as for cell

    .11 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell

    ,. T#e R& le+el of cell is

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    44/96

    / ;hen a ailure such as case e o clause 4.4.4.3 o TS 24.008 has occurred during a normal location updatingprocedure and when an emergenc$ call establishment is requested b$ the user the &ser %quipment, i it supportsspeech, shall send a ! Ser#ice (equest message with ! Ser#ice T$pe I% set to "emergenc$ callestablishment", 7S I% set to "no e$ a#ailable" and !obile Identit$ I% set to its I!SI and ater acceptanceb$ the networ it shall send an %mergenc$ Setup message.

    4 ;hen a ailure such as cases d, and g o clause 4.4.4.3 o TS 24.008 has occurred during a normal locationupdating procedure the &ser %quipment shall use a request rom ! entit$ other than emergenc$ call as atrigger or a normal location updating procedure and shall send a Cocation &pdating (equest message with the!obile Identit$ I% set to its I!SI, 7S I% set to "no e$ is a#ailable" and the Cocation &pdating t$pe I% setto "normal location updating".

    @ ;hen a ailure such as cases d, and g o clause 4.4.4.3 o TS 24.008 has occurred during a normal locationupdating procedure the &ser %quipment shall answer to paging with I!SI and shall send a 'aging (esponsemessage with 7S I% set to "no e$ a#ailable" and !obile Identit$ I% set to its I!SI.

    H ;hen a ailure such as cases d, and g o clause 4.4.4.3 o TS 24.008 has occurred during a normal locationupdating procedure the &ser %quipment shall perorm a normal location updating procedure as soon as it entersa new cell.

    References

    TS 24.008 lauses 4.4.4.2, 4.4.4.3.

    9.6.".!.! Test purpose

    To #eri$ that the &% perorms normal location updating procedures when its attempt counter is smaller than 4.

    To chec that the &% does not perorm the I!SI detach procedure when "idle not updated".

    To #eri$ that when "idle not updated" the &% can perorm an emergenc$ call.

    To #eri$ that when "idle not updated" the &% uses requests rom ! la$er other than emergenc$ call as triggering oa normal location updating procedure.

    To #eri$ that the &% perorms a normal location updating procedure i it enters a new cell while being "idle notupdated".

    9.6.".!." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5 o the same 'C!, belonging to dierent location areas with CI a and b?

    * TT lag shall be set to I!SI attach:detach allowed.

    * &ser %quipment

    * the &% is "idle updated" on cell . #alid 7S #alue is stored in the SI! and is noted "initial 7S". T!SI is allocated.

    Related ICS$I%IT statements

    SI! remo#al possible while &% is powered 9es:o.

    Switch o on button 9es:o.

    Support or speech 9es:o.

    &oreseen final state of t#e 'E

    The &% is "Idle updated" on cell with a #alid 7S and a T!SI.

    3GPP

    44

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    45/96

    Test rocedure

    The &% is made to perorm a normal location updating procedure. Eour t$pes o ailure cases are triggered

    * sending o a Cocation &pdating (e>ect with cause randoml$ chosen between all deined cause #alues except 2,/, H, 11, 12 and 1/ -which trigger a dierent action -case g o TS 24.008 clause 4.4.4.3?

    * ((*connection ailure -case d?

    * sending o a ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    46/96

    E)pected sequence

    3GPP

    46

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    47/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+ed on cell ,.

    1 'E T#e R& le+el of cell is lo*ered until t#e 'E selects cell,. T#e R& le+el of cell is set sufficiently lo* to ensuret#at cell is not suitable as defined in subclause ..!.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 initial +alue;7I 2 a; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    8 70CTI0- '/TI-4 REECT IE ReBect cause is set to a +alue arbitrarily c#osen3 J intable 1>. of; causes K!; K"; K; K11; K1! and K1"being e)cluded.

    RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling lin 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    48/96

    Step Direction Message Comments

    UE SS

    SS I-ITITE/ RRCC0--ECTI0-

    sent continuously to t#e 'E during = seconds.

    3GPP

    48

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    49/96

    Step Direction Message Comments

    UE SS

    "! SS T#e SS c#ec are performed - times. - s#all be

    c#osen in suc# a *ay t#at T"!1> e)pires. /epending on*#en T"!1> e)pires in t#e 'E; it is possible t#at on t#e-t# occurrence of step 8> t#e 'E may send a 7! /ISCrat#er t#an t#e 'TAE-TICTI0- RES0-SEmessage.

    69 SS T#e SS c#ec 'E If t#e 'E supports speec# it is made to perform anemergency call.

    81 RRC C0--ECTI0- RE?'EST Establis#ment cause3 Emergency call.8! RRC C0--ECTI0- SET'8" CM SERDICE RE?'EST CM ser+ice type 2 Emergency call establis#mentL C@S-

    2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    50/96

    Step Direction Message Comments

    UE SS

    C0M7ETE8 RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin to =" are optional as t#e 'E may #a+e

    memoried t#e request for CM connection attempt Nait1> s to decide *#et#er to go directly to step =6.

    := RRC C0--ECTI0- RE?'EST Establis#ment cause3 -ot c#ecs.

    =9 RRC C0--ECTI0- SET'9> 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    51/96

    Specific message contents

    one.

    9.6."." 7ocation updating $ abnormal cases $ attempt counter equal to 6

    9.6.".".1 Conformance requirement

    1 ;hen our ailures such as cases d to g o clause 4.4.4.3 o TS 24.008 ha#e occurred during a normal locationupdating procedure the &ser %quipment shall

    1.1 perorm location updating ater T/212 expir$ b$ sending a Cocation &pdating (equest message with the!obile Identit$ I% set to its I!SI, 7S I% set to "no e$ is a#ailable" and the Cocation &pdating t$pe setto "normal updating"?

    1.2 i the T/212 initiated location updating was unsuccessul, then ater T/211 expir$ the &ser %quipment shallsend a Cocation &pdating (equest message with the !obile Identit$ I% set to its I!SI, 7S I% set to "noe$ is a#ailable" and the Cocation &pdating t$pe I% set to "normal location updating".

    2 ;hen our ailures such as cases d, , g o clause 4.4.4.3 o TS 24.008 ha#e occurred during a normal

    location updating procedure the &ser %quipment, i it supports speech, shall be able to perorm an emergenc$call i.e. the &ser %quipment is able to send a ! Ser#ice (equest message with the ! Ser#ice T$pe I% set to"emergenc$ call establishment", 7S I% set to "no e$ is a#ailable" and !obile Identit$ I% set to its I!SI andthen send an %mergenc$ Setup message.

    / ;hen our ailures such as cases d, , g o clause 4.4.4.3 o TS 24.008 ha#e occurred during a normallocation updating procedure

    /.1 the &ser %quipment shall use a request rom ! entit$ or !! connection or a ser#ice other thanemergenc$ call as a trigger or a normal location updating procedure and shall send a Cocation &pdating(equest message with the !obile Identit$ I% set to its I!SI, 7S I% set to "no e$ is a#ailable" and theCocation &pdating t$pe I% set to "normal location updating"?

    /.2 ater a location updating triggered b$ a request rom the ! la$er which was .unsuccessul, ater T/211

    expir$ the &ser %quipment shall send a Cocation &pdating (equest message with the !obile Identit$ I% setto its I!SI, 7S I% set to "no e$ is a#ailable" and the Cocation &pdating t$pe I% set to "normal locationupdating".

    4 ;hen our ailures such as cases d, , g o clause 4.4.4.3 o TS 24.008 ha#e occurred during a normallocation updating procedure

    4.1 the &ser %quipment shall perorm a normal location updating procedure i it enters a new cell?

    4.2 i this location updating is unsuccessul, ater T/211 expir$ the &ser %quipment shall send a Cocation&pdating (equest message with the !obile Identit$ I% set to its I!SI, 7S I% set to "no e$ is a#ailable"and the Cocation &pdating t$pe I% set to "normal location updating".

    References

    TS 24.008 lause 4.4.4.3.

    9.6.".".! Test purpose

    To #eri$ that the &% perorms normal location updating procedures ater T/212 expir$, when its attempt counter hasreached #alue 4 and that the &% reset its attempt counter ater a timer T/212 expir$.

    To #eri$ that the &% still ollows the !! I+C% TT%!'TI) T< &'+T% state requirements ater its attemptcounter has reached #alue 4.

    To #eri$ that the attempt counter is reset in the cases where it has to be done.

    3GPP

    51

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    52/96

    9.6."."." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5, belonging to dierent location areas a and b?* I!SI attach:detach is allowed in both cells?

    * T/212 is set to H minutes.

    * &ser %quipment

    * the &% is "Idle updated" on cell 5 with a #alid 7S and a T!SI.

    Related ICS$I%IT statements

    SI! remo#al possible while &% is powered 9es:o.

    Switch o on button 9es:o.

    Support o speech 9es:o.

    &oreseen final state of t#e 'E

    The &% is "Idle updated" on cell with a #alid 7S and a T!SI.

    Test rocedure

    The &% is made to perorm a normal location updating. The SS triggers a ailure in this procedure. ter T/211 expir$the &% will tr$ again the location updating procedure. The SS triggers again a ailure. This is done again 2 times. tthis point the attempt counter shall be equal to 4. It is then checed that T/212 has been started and that at its expir$the &% will tr$ a normal location updating procedure. It is #eriied that the &% has reset its attempt counter ater timer

    T/212 expir$.

    Then it is checed that, when the attempt counter has reached the #alue o 4, the &% is in the !! I+C% state andTT%!'TI) T< &'+T% substate, that is

    * not perorm an I!SI detach procedure?

    * support request or emergenc$ call?

    * use requests rom ! la$er other than emergenc$ call as triggering o a normal location updating procedure?

    * perorm normal location updating procedure when a new cell is entered.

    3GPP

    52

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    53/96

    E)pected sequence

    3GPP

    53

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    54/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell .

    1 'E T#e R& le+el of cell , is lo*ered until t#e 'E selects cell. T#e R& le+el of cell , is set sufficiently lo* to ensuret#at cell , is not suitable as defined in subclause ..!.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 initial +alue;7I 2 b; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    8 70CTI0- '/TI-4 REECT IE ReBect cause is set to K!! J in table 1>. of; causesK!; K"; K; K11; K1! and K1" being e)cluded.

    RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signallinglin e)pires. /ependingon *#en T"!1> e)pires in t#e 'E; it is possible t#at ont#e -t# occurrence of step 8> t#e 'E may send a 7!/ISC rat#er t#an t#e 'TAE-TICTI0- RES0-SEmessage.

    1= 'E T#e 'E s#all cease transmission (after t#e /ISC$'e)c#ange #as been completed and t#en s#all not initiatean RRC connection establis#ment on cell or on cell ,during T"!11 seconds at least after t#e e)piry of T"!1>.

    19 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.!> RRC C0--ECTI0- SET' !1 70CTI0- '/TI-4

    RE?'EST

    location updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    55/96

    Step Direction Message Comments

    UE SS!= RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signalling

    lin RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating."1 RRC C0--ECTI0- SET'"! 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no RRC C0--ECTI0- SET'81 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    56/96

    Step Direction Message Comments

    UE SS8: SS performs step 6! *it# cause K"= and step 6".8= 'E If t#e 'E supports speec#; it is made to perform an

    emergency call.89 RRC C0--ECTI0- RE?'EST Establis#ment cause3 Emergency call.> RRC C0--ECTI0- SET'

    1 CM SERDICE RE?'EST CM ser+ice type 2 Emergency call establis#mentL C@S-2 no . of; causesK!; K"; K; K11; K1!; and K1" being e)cluded.

    =! RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signallinglin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    57/96

    Step Direction Message Comments

    UE SSRE?'EST a+ailable; 7I 2 deleted 7I (t#e MCC and M-C #old t#e

    pre+ious +alues; t#e 7C is coded &&&E; Mobile Identity2 IMSI.

    3GPP

    57

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    58/96

    Step Direction Message Comments

    UE SS9! RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signalling

    lin RRC C0--ECTI0- SET'1>1 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no ! SS performs step 8!.1>" 'E T#e 'E s#all not initiate an RRC connection

    establis#ment on cell or on cell , during T"!11seconds at least after t#e RRC C0--ECTI0- release.

    1>6 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.1>8 RRC C0--ECTI0- SET'1> 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no : 'TAE-TICTI0- RE?'EST C@S- 2 initial [email protected]>= 'TAE-TICTI0- RES0-SE1>9 70CTI0- '/TI-4 CCET IE mobile Identity 2 ne* TMSI.11> TMSI RE770CTI0-

    C0M7ETE111 RRC C0--ECTI0- RE7ESE 'E is no* idle; updated in cell T#e 'E may or maynot #a+e memoried t#e request for CM connection. T#esteps 11! to 11 are t#erefore optional for t#e 'E. T#eSS *aits 1> second *#et#er to decide to go directly tostep 11:.

    11! RRC C0--ECTI0- RE?'EST11" RRC C0--ECTI0- SET'116 CM SERDICE RE?'EST C@S- 2 initial +alue; Mobile identity 2 TMSI.118 CM SERDICE REECT cause K1: (net*or< failure.11 RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signalling

    lin 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 initial +alue;7I 2 a; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    1!1 70CTI0- '/TI-4 REECT IE ReBect cause is set to K"= J in table 1>. of; causesK!; K"; K; K11; K1! and K1" being e)cluded.

    1!! RRC C0--ECTI0- RE7ESE T#e SS *aits for t#e disconnection of t#e main signallinglin RRC C0--ECTI0- SET'61 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 periodic; C@S- 2 initial +alue;7I 2 b; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    6! SS performs step 8 of 9.6.".! *it# cause K1: and step of9.6.".!.

    6" 'E T#e 'E s#all not initiate an RRC connectionestablis#ment during T"!11 at least after t#e RRCC0--ECTI0- release.

    66 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.68 RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 periodic; C@S- 2 initial +alue;7I 2 b; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    6: SS performs step 11 of 9.6.".!.6= 'E T#e 'E s#all not initiate an RRC connection

    establis#ment *it#in T"!11 Radio7in.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 periodic; C@S- 2 initial +alue;7I 2 b; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    8 SS performs step 8 of 9.6.".! *it# cause K1: and step of9.6.".!.

    'E T#e 'E s#all not initiate an RRC connectionestablis#ment during T"!11 at least after t#e RRC

    C0--ECTI0- release.: RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.= RRC C0--ECTI0- SET'

    3GPP

    64

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    65/96

    Step Direction Message Comments

    UE SS9 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 periodic; C@S- 2 initial +alue;7I 2 b; mobile station classmar< 1 as gi+en by t#e ICSand mobile identity 2 TMSI.

    :> SS performs step 11 of 9.6.".!.:1 'E T#e 'E s#all not initiate an RRC connection

    establis#ment *it#in T"!11 Radio7in SS performs step 8 of 9.6.".! *it# cause K1: and step of

    9.6.".!.=1 'E M0 CM connection is attempted.=! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.=" RRC C0--ECTI0- SET'=6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no " 'E T#e 'E s#all not initiate an RRC connection

    establis#ment *it#in T"!11 Radio7in6 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.1>8 RRC C0--ECTI0- SET'

    1> 70CTI0- '/TI-4RE?'EST

    location updating type 2 IMSI attac#; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    66/96

    Step Direction Message Comments

    UE SSby t#e ICSand mobile identity 2 TMSI.

    3GPP

    66

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    67/96

    Step Direction Message Comments

    UE SS1>: RRC C0--ECTI0- RE7ESE fter t#e sending of t#e message t#e SS *aits for t#e

    disconnection of t#e main signalling lin= 'E T#e 'E s#all not initiate an RRC connection

    establis#ment during T"!11 at least after t#e RRCC0--ECTI0- release.

    1>9 RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.11> RRC C0--ECTI0- SET'111 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 IMSI attac#; C@S- 2 no RRC C0--ECTI0- SET'1!1 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 periodic or normal or IMSIattac# (see -ote !; C@S- 2 no t#e'E is broug#t bac< to operation.

    1"" RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.1"6 RRC C0--ECTI0- SET'1"8 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 IMSI attac#; C@S- 2 initial+alue; 7I 2 b; mobile station classmar< 1 as gi+en byt#e ICSand mobile identity 2 TMSI.

    1" SS performs step 1 of 9.6.".!.1": 'E T#e 'E s#all not initiate an RRC connection

    establis#ment during T"!11 at least after t#e RRCC0--ECTI0- release.

    1"= RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.1"9 RRC C0--ECTI0- SET'

    16> 70CTI0- '/TI-4RE?'EST

    location updating type 2 IMSI attac#; C@S- 2 initial+alue; 7I 2 b; mobile station classmar< 1 as gi+en byt#e ICSand mobile identity 2 TMSI.

    3GPP

    67

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    68/96

    Step Direction Message Comments

    UE SS161 SS performs step 8 of 9.6.".! *it# cause K1: and step of

    9.6.".!.16! 'E T#e 'E s#all not initiate an RRC connection

    establis#ment during T"!11 at least after t#e RRCC0--ECTI0- release.

    16" RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.166 RRC C0--ECTI0- SET'168 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 IMSI attac#; C@S- 2 initial+alue; 7I 2 b; mobile station classmar< 1 as gi+en byt#e ICSand mobile identity 2 TMSI.

    16 SS performs step 11 of 9.6.".!.16: 'E T#e 'E s#all not initiate an RRC connection

    establis#ment *it#in T"!11 Radio7in 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 IMSI attac#; C@S- 2 initial+alue; 7I 2 b; mobile station classmar< 1 as gi+en byt#e ICSand mobile identity 2 TMSI.

    181 SS performs step 1 of 9.6.".!.18! 'E T#e 'E is made to perform a M0 call.18" RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating.186 RRC C0--ECTI0- SET'188 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no RRC C0--ECTI0- RE7ESE

    Steps 11 to 1 are optional.11 'E n M0 CM connection is attempted.1! RRC C0--ECTI0- RE?'EST1" RRC C0--ECTI0- SET'16 CM SERDICE RE?'EST C@S- 2 initial +alue; Mobile identity 2 TMSI.18 CM SERDICE REECT cause K1: (net*or< failure.1 RRC C0--ECTI0- RE7ESE

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    69/96

    9.6.6.! Test purpose

    To #eri$ that the &% aborts the ((*connection at the expir$ o timer T/240.

    9.6.6." Met#od of test

    Initial conditions

    * S$stem Simulator

    * two cells and 5, belonging to dierent location areas a and b.

    * &ser %quipment

    * the &% has a #alid T!SI. It is "idle updated" on cell .

    Related ICS$I%IT statements

    one.

    &oreseen final state of t#e 'E

    The &% is "idle updated" on cell 5.

    Test rocedure

    normal location updating procedure is perormed. The ((*connection is not released b$ the SS within the timerT/240. It is checed that the &% aborts the ((*connection.

    E)pected sequence

    Step Direction Message CommentsUE SS

    1 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell,.

    ! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST8 70CTI0- '/TI-4 CCET SS T#e SS *aits T"!6> e)piry.: 'E T#e 'E s#all abort t#e RRC connection (disconnection

    of layer !.

    Specific message contents

    one.

    9.6.8 7ocation updating $ periodic

    9.6.8.1 7ocation updating $ periodic spread

    9.6.8.1.1 Conformance requirement

    1 The &ser %quipments shall perorm spreading o the time beore perorming a periodic location updating whenthe location updating timer #alue is reduced.

    2 The &ser %quipment shall reset timer T/212 when the &ser %quipment is deacti#ated, and shall start with a#alue between Mero and the broadcasted #alue when reacti#ated in the same cell, I!SI attach being orbidden.

    3GPP

    69

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    70/96

    / ;hen acti#ated the &ser %quipment shall start timer T/212 with a #alue randoml$ drawn in the allowed range.

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    71/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1 'E T#e 'E is acti+ated.! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'

    6 70CTI0- '/TI-4RE?'EST

    location updating type3 IMSI attac#.

    8 70CTI0- '/TI-4 CCET RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    72/96

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    73/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1 'E M0 CM connection is attempted.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'

    6 CM SERDICE RE?'EST8 CM SERDICE REECT cause K1: (net*or< failure. RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 70CTI0- '/TI-4

    RE?'EST7ocation updating type 2 periodic.

    11 70CTI0- '/TI-4 CCET1! RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    74/96

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    75/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+edon cell ,.

    1 SS T#e R& le+el of cell is lo*ered until t#e 'E selects cell

    ,.! RRC C0--ECTI0- RE?'EST establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal.

    8 70CTI0- '/TI-4 CCET RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 70CTI0- '/TI-4

    RE?'EST7ocation updating type 2 periodic.

    11 70CTI0- '/TI-4 CCET1! RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    76/96

    9.6.8.6 7ocation updating $ periodic A7M- searc#

    9.6.8.6.1 7ocation updating $ periodic A7M- searc# $ 'E *aits time T

    9.6.8.6.1.1 Conformance requirement

    ;hen in automatic mode and roaming in the home countr$, the &% shall mae an attempt to access the ='C!, ithe &% is on the B'C! at time T ater since the last attempt.

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    77/96

    E)pected sequence

    Step Direction Message Contents

    UE SS

    T#e follo*ing messages s#all be sent and recei+ed onCell ,.

    1 'E T#e 'E is s*itc#ed on by eit#er using t#e o*er S*itc#

    or by applying po*er.! RRC C0--ECTI0- RE?'EST Establis#ment cause3 7ocation updating." RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'EST7ocation 'pdate Type3 -ormal.

    8 70CTI0- '/TI-4 CCET RRC C0--ECTI0- RE7ESE fter sending t#is message t#e SS *aits for t#e

    disconnection of t#e main signalling lin RRC C0--ECTI0- SET'11 70CTI0- '/TI-4

    RE?'EST7ocation 'pdate Type3 normal.

    1! 70CTI0- '/TI-4 CCET1" RRC C0--ECTI0- RE7ESE fter sending t#is message t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    78/96

    Related ICS$I%IT statements

    Switch on:o button 9es:o.

    &oreseen final state of t#e 'E

    The &% is "idle updated" on ell 5.

    Test rocedure

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    79/96

    * two cells and 5, belonging to dierent location areas with location identiication a and b. ell shall be acell o the ='C! and ell 5 shall be a cell o the B'C! with a ountr$ ode the same as that o ell. Initiall$ ell shall not be broadcasting. I!SI attach:detach is not allowed on either cell.

    * &ser %quipment

    * the &% is switched o. The ='C! Search 'eriod on the SI! shall be set to H minutes. The location area

    inormation on the SI! is "deleted".

    Related ICS$I%IT statements

    Switch on:o button 9es:o.

    &oreseen final state of t#e 'E

    The &% is "idle updated" on ell .

    Test rocedure

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    80/96

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    81/96

    ater the end o the I!SI attach procedure. The &% shall perorm a periodic location update on cell a between 11,@minutes and 12,2@ minutes ater the end o the I!SI attach procedure.

    / minutes ater the end o the periodic location updating procedure, cell a is switched o. The &% shall not locationupdate on cell b. 14 minutes ater the end o the periodic location updating procedure, cell a is switched on and cell bis switched o. The &% shall perorm a location update on cell a beore 1 minutes ater the end o the periodiclocation updating procedure.

    E)pected sequence

    Step Direction Message Comments

    UE SS1 'E T#e 'E is acti+ated in automatic net*or< selection

    mode.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'6 70CTI0- '/TI-4

    RE?'ESTlocation updating type3 IMSI attac#.

    8 70CTI0- '/TI-4 CCET RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin RRC C0--ECTI0- SET'11 70CTI0- '/TI-4

    RE?'ESTlocation updating type3 periodic updating.

    1! 70CTI0- '/TI-4 CCET1" RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    82/96

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    83/96

    Specific message contents

    one.

    9.8." MM connection $ establis#ment *it#out cip#er

    9.8.".1 Conformance requirement

    &pon reception o the ! S%(BI% %'T message, the &% shall send a ! message.

    References

    TS 24.008 lause [email protected].

    9.8.".! Test purpose

    To #eri$ that the &% can correctl$ set up an !! connection in an originating ! connection establishment whensecurit$ mode setting is not required.

    9.8."." Met#od of test

    Initial conditions

    * S$stem Simulator

    * 1 cell, deault parameters.

    * &ser %quipment

    * the &% has a #alid T!SI. It is "idle updated".

    Related ICS$I%IT statements

    one.

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI. It is "idle updated".

    Test rocedure

    mobile originating ! connection is attempted. The !!*connection is established without in#oing the securit$mode setting procedure.

    Then, the &% sends a ! message and the SS releases the ((

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    84/96

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1 'E M0 CM connection is attempted.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'

    6 CM SERDICE RE?'EST8 CM SERDICE CCET

    SET'

    , RE4ISTER

    C C/TC: CC@C= C/TC9 CC@

    1> RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling linected b$ the SS.

    9.8.6." Met#od of test

    Initial conditions

    * S$stem Simulator

    * 1 cell, deault parameters.

    * &ser %quipment

    * the &% has a #alid T!SI. It is "idle updated".

    Related ICS$I%IT statements

    one.

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI? It is "idle updated".

    3GPP

    84

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    85/96

    Test rocedure

    mobile originating ! connection is attempted. ter the &% has sent the ! S%(BI% (%A&%ST message to theSS, the SS responds with a ! S%(BI% (%L%T message with re>ect cause "requested ser#ice option notsubscribed". It is checed that the &% does not send a la$er / message.

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1 'E M0 CM connection is attempted! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'6 CM SERDICE RE?'EST8 CM SERDICE REECT ReBect cause IE3 requested ser+ice option not

    subscribed. SS T#e 'E s#all not send a layer " message. T#is is

    c#ec

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    86/96

    Related ICS$I%IT statements

    one.

    &oreseen final state of t#e 'E

    The &% has #alid T!SI, 7S. It is "idle updated".

    Test rocedure

    mobile originating ! connection is attempted. ter the &% has sent the ! S%(BI% (%A&%ST message to theSS, the SS responds with a ! S%(BI% (%L%T message with re>ect cause "I!SI unnown in BC(".

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    87/96

    9.8.." Met#od of test

    Initial conditions

    * S$stem Simulator

    * 1 cell, deault parameters.* &ser %quipment

    * the &% has a #alid T!SI. It is "idle updated".

    Related ICS$I%IT statements

    one.

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI. It is "idle updated".

    Test rocedure

    mobile originating ! connection is attempted. ter the &% has sent the ! S%(BI% (%A&%ST message to theSS, the SS waits or expir$ o timer T/2/0. It is checed that the &% does not send a la$er / message but waits or therelease o the ((*connection.

    E)pected sequence

    Step Direction Message Comments

    UE SS

    1 'E M0 CM connection is attempted.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'

    6

    CM SERDICE RE?'EST8 SS T#e SS *aits for e)piry of timer T"!">. CM SERDICE CCET: MM STT'S ReBect cause IE is message not compatible *it# t#e

    call state or not implemented.= RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    88/96

    2.4 re>ect an$ request or !obile

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    89/96

    E)pected Sequence

    3GPP

    89

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    90/96

    Step Direction Message Comments

    UE SS

    T#e follo*ing messages are sent and s#all be recei+ed on cell ,

    1 'E mobile originating CM connection is attempted.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'

    6 O CM SERDICE RE?'EST8 'TAE-TICTI0- RE?'EST 'TAE-TICTI0- RES0-SE: ,0RT reBect cause 2 K.= SS T#e SS *aits for 8 seconds.9 'E T#e 'E s#all not send any layer " message during t#at

    time.1> RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin 70CTI0- '/TI-4

    RE?'ESTlocation updating type 2 normal; C@S- 2 no

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    91/96

    Step Direction Message Comments

    UE SSdisconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    92/96

    E)pected Sequence

    This procedure is perormed i the &% supports non call related supplementar$ ser#ice operation.

    Step Direction Message Comments

    UE SS

    1 'E non call related supplementary ser+ice operation is

    attempted at t#e 'E.! CM SERDICE RE?'EST" CM SERDICE CCET6 RE4ISTER8 ,0RT reBect cause 2 K1:. /ISC0--ECT *it# t#e TI of t#e mobile terminating call.: RE7ESE C0M7ETE cause 2 K=1. Same / and TI as t#e /ISC0--ECT

    message.= RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#e

    disconnection of t#e main signalling lin

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    93/96

    Test procedure

    The &% is acti#ated and a ! connection is attempted during the location updating procedure. The SS does notinclude the ollow on proceed inormation element in the C

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    94/96

    &oreseen final state of t#e 'E

    The &% has a #alid T!SI. It is "idle updated".

    Test procedure

    The &% is acti#ated and a ! connection is attempted during the location updating procedure. The SS includes theollow on proceed inormation element in the C

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    95/96

    9.8.=." MM connection $ follo*on request pending $ test "

    9.8.=.".1 Conformance requirement

    1 The &% shall not set the ollow on request bit in a C

    95

  • 8/12/2019 T1S-000092_rev2 (MM Formated)

    96/96

    E)pected Sequence

    Step Direction Message Comments

    UE SS

    1 'E T#e 'E is acti+ated.! RRC C0--ECTI0- RE?'EST" RRC C0--ECTI0- SET'

    6 70CTI0- '/TI-4RE?'EST

    7ocation updating type 2 IMSI attac#. T#e &0R bit isset to -o follo*on request pending.

    8 70CTI0- '/TI-4 CCET follo* on proceed IE is included. SS T#e SS *ait for 8 seconds.: 'E T#e 'E s#all not send any layer " message for 8

    seconds after reception of t#e 70CTI0- '/TI-4CCET message.

    = SET'

    If t#e 'E supports a basic ser+ice on TCA.9 C77 C0-&IRME/

    If t#e 'E does not support any basic ser+ice on TCA.,9 RE7ESE C0M7ETE cause K==.

    1> RRC C0--ECTI0- RE7ESE fter t#e sending of t#is message; t#e SS *aits for t#edisconnection of t#e main signalling lin


Recommended