Date post: | 30-Dec-2015 |
Category: |
Documents |
Upload: | merritt-davidson |
View: | 41 times |
Download: | 0 times |
T4L – NSW DET SOET4L – NSW DET SOEMuticasting an ImageMuticasting an Image
ProblemProblem
New T4L computers use SATA HDD’s
SATA drives are not recognised by Current DET Licensed version of GhostV7.01 Corporate Edition
Attempts to ghost from a floppy boot disk result in error 24010.
New T4L computers use SATA HDD’s
SATA drives are not recognised by Current DET Licensed version of GhostV7.01 Corporate Edition
Attempts to ghost from a floppy boot disk result in error 24010.
Windows DomainsWindows Domains
If the PC has been joined to a Windows domain you must run the following registry patch BEFORE capturing an image.C:\DETapps\Support\Source\~scripts\dompassw.reg
By default, Windows automatically changes the password on the local computer account at regular intervals
When you restore an image it will have an 'old' domain computer account password and so the Windows domain will reject the computer ie. prevent the PC from rejoining the domain again
NB. This is the domain computer account and NOT a user account.
If the PC has been joined to a Windows domain you must run the following registry patch BEFORE capturing an image.C:\DETapps\Support\Source\~scripts\dompassw.reg
By default, Windows automatically changes the password on the local computer account at regular intervals
When you restore an image it will have an 'old' domain computer account password and so the Windows domain will reject the computer ie. prevent the PC from rejoining the domain again
NB. This is the domain computer account and NOT a user account.
Ghost MulticastGhost Multicast
1. Download Necessary Files2. Prepare ASI computers – network
drivers3. Set up “Model”4. Setup Multicast Server5. Take image of Model – whole disk6. Multicast image to all Targets – whole
disk7. Perform Post imaging tasks8. Create Local Current Image
1. Download Necessary Files2. Prepare ASI computers – network
drivers3. Set up “Model”4. Setup Multicast Server5. Take image of Model – whole disk6. Multicast image to all Targets – whole
disk7. Perform Post imaging tasks8. Create Local Current Image
1. Download Necessary Files
1. Download Necessary Files
ASIRecoveryUpdate.exe http://www.sydneyr.det.nsw.edu.au/ASI/
ASIRecoveryUpdate.exe Recoveryfix.bat
http://www.sydneyr.det.nsw.edu.au/ASI/Recoveryfix.bat
Newsid.exe http://www.sydneyr.det.nsw.edu.au/ASI/
newsid.exe Symantec Ghost
http://software.det.nsw.edu.au/downloads/symantec/Ghost/Ghost.htm
ASIRecoveryUpdate.exe http://www.sydneyr.det.nsw.edu.au/ASI/
ASIRecoveryUpdate.exe Recoveryfix.bat
http://www.sydneyr.det.nsw.edu.au/ASI/Recoveryfix.bat
Newsid.exe http://www.sydneyr.det.nsw.edu.au/ASI/
newsid.exe Symantec Ghost
http://software.det.nsw.edu.au/downloads/symantec/Ghost/Ghost.htm
2. Prepare ASI computers2. Prepare ASI computers
• Run ASIRecoveryUpdate.exe to produce Update floppy.
• Boot with Update floppy on ALL ASI T4L computers.
• Installs network drivers to recovery partition
• Run ASIRecoveryUpdate.exe to produce Update floppy.
• Boot with Update floppy on ALL ASI T4L computers.
• Installs network drivers to recovery partition
3. Set up “Model”3. Set up “Model”
• Commission computer• Create Local admin User – Build• Log in as build• Install all software and configure• Install Novell Client/Zenworks if required• Install all network printers• Login as Local Admin• Copy Build Profile to Default User• Remove any other local user profiles• If you needed to join a domain – remove
computer from domain
• Commission computer• Create Local admin User – Build• Log in as build• Install all software and configure• Install Novell Client/Zenworks if required• Install all network printers• Login as Local Admin• Copy Build Profile to Default User• Remove any other local user profiles• If you needed to join a domain – remove
computer from domain
4. Setup Multicast Server4. Setup Multicast Server
• Install Ghost – Standard tools only
• Use any windows Workstation – not target to model
• Install Ghost – Standard tools only
• Use any windows Workstation – not target to model
5. Take image of Model5. Take image of Model• Start Multicast Session
• Dump from Client• Whole disk
• Set up Model• Boot Model to Rebuild Menu• Restricted Menu – Console• Options – Image/Tape
• Image Boot
• Start Multicast Session• Dump from Client• Whole disk
• Set up Model• Boot Model to Rebuild Menu• Restricted Menu – Console• Options – Image/Tape
• Image Boot
• Join Session• Take image
6. Multicast image to all Targets
6. Multicast image to all Targets
• Prepare Multicast Server• Whole drive
• Boot each target• Rebuild menu• Restricted• Console• Join Session• Change partition sizes to match
original
• Prepare Multicast Server• Whole drive
• Boot each target• Rebuild menu• Restricted• Console• Join Session• Change partition sizes to match
originalSend imageSend image
7. Perform Post imaging tasks
7. Perform Post imaging tasks
• Run NewSID.exe and assign new computer name
• Join Domain if required• Run
C:\DETapps\Support\Source\~scripts\dompassw.reg
• Run Recoveryfix.bat if required• Install Local printers, custom
software• Set default Printer
• Run NewSID.exe and assign new computer name
• Join Domain if required• Run
C:\DETapps\Support\Source\~scripts\dompassw.reg
• Run Recoveryfix.bat if required• Install Local printers, custom
software• Set default Printer
8. Create Local Current Image
8. Create Local Current Image
• Reboot PC and enter Rebuild menu• Restricted• Capture Current image
• Reboot PC and enter Rebuild menu• Restricted• Capture Current image