Note: Total Colours Allura Red AC + Sunset Yellow FCF in finished product calculated at less than 290 mg/kg.Made in a facility that processes milk, eggs, soy, wheat, peanuts and treenuts.Seek medical advice if you have any questions on your condition and should a reaction occur.
REMEMBER: • Wash all parts before and immediately after use.• Wash hands before you start.• Read all instructions carefully to have fun and to get great results.• This is messy fun. Make sure you set up in an area where leaks and spills can be easily cleaned up.• For best results, complete each individual experiment without interuption. Consume right away.
CHOKING HAZARD - Small parts. Not for children under 3 years.
! WARNING: YEARS5+
CONTENTS
100908070605040302010
958575655545352515
(G) Brain Beaker
(F) Brain Valve
(D) Head Front
( J) Monocle Mold
(H) Worm Mold
(N) Stir Stick/Scoop
(B) GearPosts
(O) Tweezers
(P) Measuring Cup (R) 6 Packages of Candyand Drink Mixes
(M) Food Injector Nozzle
(L) Food Injector
(K) Plunger
(C) Jaws
TROUBLESHOOTING
Washing and Care Instructions:• Fully disassemble your Zombie Lab as shown in contents diagram (see front page).• Allow the parts to soak in warm soapy dishwater.• Use cleaning brush (not included) to clean hard to reach places.• Use cotton swab to clean nozzle if necessary.• Wipe down all parts with a dishcloth and rinse thoroughly under hot water. Air dry or dry with hand towel.• DO NOT put in dishwasher or microwave.
PROBLEM SOLUTIONMix has hardened.
Brain leaking before barf is released.
Liquids inside brain not flowing out correctly.
Bugs not solid enough.
Bugs setting too quickly.
Bug mold difficult to fill.
This may happen during storage. Break up the pieces with a spoon until the mix returns to a powder state. Stir for a few extra minutes for any clumps to dissolve into liquid.
Make sure valve is tightly screwed in before flipping.
Do not let liquids set. Use warmer water before mixing.
Place in fridge for an additional 5 or 10 minutes.
IMPORTANT INFORMATION: Content may vary from pictures. Retain this information, addresses and phone numbers for future reference. Remove all packaging before use. Meets CPSC safety requirements.
a WARNING: CHOKING HAZARD – Small parts. Not suitable for children under three years.
2 3
BUBBLING BRAINS
1
Watch brains grow.Eat and Enjoy.
3Add 15 units of water and stir.2
15 units
100908070605040302010
958575655545352515Mix 2 scoops
of Brain Mix...
...with 3 scoops of Brain Activator Mix. Stir.
NOTE: Contents may spill over. Use placemat or tray for easy cleanup.NOTE: Contents may spill over. Use placemat or tray for easy cleanup.
x 2 x 3
ZOMBIE SKIN
ASSEMBLY
1
A
BB
C
2Connect front and back of head together (D, E) and slide down onto jaws (C). Roll eye forward.
Connect front and back of head together (D, E) and slide down onto jaws (C). Roll eye forward.
C
D
E
3
Screw valve (F) into brain beaker (G). Place in skull.Screw valve (F) into brain beaker (G). Place in skull.
FG
4 H
JD
Snap molds (H,J) to head front (D) as shown. Ensure holes are facing forward.Snap molds (H,J) to head front (D) as shown. Ensure holes are facing forward.
5
Add measuring cup and accessories as shown.Add measuring cup and accessories as shown.
Attach gear posts (B) to base (A). Attach jaws (C) to gear posts (B).Attach gear posts (B) to base (A). Attach jaws (C) to gear posts (B).
Pour onto plate or wax paper. Place in refrigerator for 10 minutes.
2Peel and Eat!Peel and Eat!3
100908070605040302010
958575655545352515
NOTE: For best results use very WARM water. Do not use cold waterNOTE: For best results use very WARM water. Do not use cold waterZOMBIE BARF
Drink and Enjoy.
Press down on brain to release Part 1 into Part 2.
8
100908070605040302010
958575655545352515
100908070605040302010
958575655545352515
Fill cup with water to 40 unit mark...5
100908070605040302010
958575655545352515
Place cup with Barf Mix Part 2 under skull.
6
Screw in brain valve.3
Shake brain for 5 seconds and place brain inside skull as shown.
7
100908070605040302010
958575655545352515
Pull valve up to close then set aside.
4
x 4100908070605040302010
958575655545352515
ZOMBIE BUG
Inject mixture into molds until full as shown.Inject mixture into molds until full as shown.
4Remove molds and place in refrigerator for 10 minutes.Remove molds and place in refrigerator for 10 minutes.
5Open molds and carefully remove bugs. If necessary, use the end of a paper clip to release bug. Eat and Enjoy.
Open molds and carefully remove bugs. If necessary, use the end of a paper clip to release bug. Eat and Enjoy.
6
100
90 80 70 60 50 40 30 20 10
95 85 75 65 55 45 35 25 15
Carefully place plunger in food injector without pushing out the contents.
Carefully place plunger in food injector without pushing out the contents.
3Place finger under nozzle as shown.
Pour Bug Mix into food injector and immediately go to next step before
mixture sets.
Place finger under nozzle as shown. Pour Bug Mix into food injector and
immediately go to next step before mixture sets.
2
NOTE: For best results use very WARM water. Do not use cold waterNOTE: For best results use very WARM water. Do not use cold water
Add ingredients as shown and stir until smooth.Add ingredients as shown and stir until smooth.1
2 level scoops of Bug Mix
3 level scoops of WARM water
100908070605040302010
958575655545352515
x 2 x 3
4 level scoopsof Skin Mix
4 level scoopsof WARM water
100908070605040302010
958575655545352515
Add ingredients as shown and stir until smooth.
Add ingredients as shown and stir until smooth.
1
x 4 x 4
Remove valve. Fill brain beaker with Barf Mix Part 1. For best results, avoid pouring lumps into brain.2
Rinse outafter this step.
45352515
100908070605040302010
9585756555
Fill cup with water to 90 unit mark...
...then add 3 level scoops of Barf Mix Part 1. Quickly stir until lumps are dissolved.
1
100908070605040302010
958575655545352515
x 3
...then add 4 level scoops of Barf Mix Part 2. Stir until all powder is dissolved.
