1
TA70-B8237 Quick Installation Guide Document # D2234-100/ Revision 1.0 Read Me First 1. The Barebone User’s Manual is available for download from our Web site at http://www.tyan.com. Make sure to read all precautions and instructions before you start installing the server system. 2. Refer all servicing to qualified personnel to avoid the risk of damage to the server system. 3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment. 4. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise caution when installing the processors as the manufacturer’s warranty does not cover damage inflicted upon the motherboard, including damage to the CPU sockets. Phillips Screwdriver Anti-Static Wrist Strap Flat-head Screwdriver Tools Required 1 General Information 3 System Installation Box Content Accessories 2 Motherboard Placement Note: Please save and replace the CPU protection cap when returning the server board for service. Note: - There is risk for the customers when setting the jumper by yourselves. - Customers need to add an external PCI-E VGA card. 5 Caution Motherboard Placement CONNECTORS SLOTS A CPU0 DIMM SLOT [Channel A/B/C/D] B CPU1 DIMM SLOT [Channel A/B/C/D] C PCI-E X 8 MEZZ Card D PCIE Gen2 slot (x8) E PCI-E X 1 IMC Card F PCIE Gen2 slot (x8) 1. TYAN Module Header (J96) 2. ID LED (LED1) 3. USB2.0 Port (USB5) 4. NCSI Header (J4) 5. USB2.0 Port (USB4) 6. LAN Port # 3 (LAN3) 7. VGA Header (J27) 8. IMC IPMB Header (J6) 9. System BIOS (U108) 10. SATA SGPIO Header (J63) 11. SATA Connector (SATA0~SATA5) 12. USB Front Panel Header (J91) 13/14. 4-pin Power Connector (PW2/PW1) 15. 16-pin Power Connector (PW3) Install the Memory CPU Cover for DOA/RMA Locate the External I/O Port Install the Hard Disks Quick Installation Guide x 1 Quick Installation Guide Driver's and Utilities CD x 1 Sliding Rails x 2 & Screw Pack x 1 CPU heatsink x 2 AIr Duct x 1 AC Power cord (US) x 2 AC Power Cord (EU) x 2 Screw Pack x 2 FL00EUI-A FL00EUI-A a COM Debug Jumper (JP14) b Clear CMOS Jumper (JP8) c Chassis Config Jumper (JP9/JP10) d/e COM Debug Jumper (JP11/JP12) JUMPERS Minimum Hardware Requirements To avoid integration difficulties and possible board damage, your system must meet the following minimum requirements: • Processor: AMD® Opteron® 6100 Series Processors (Magny-Cours), AMD® Opteron® 6200 Series Processors (Interlagos), AMD® Opteron® 6300 Series Processors (Abu Dhabi) • Memory Type: Minimum of one 1GB, 240-pin DDR3 800/1066/1333/1600/1866-MT/s DIMMs. • Hard Disk Drives: SATA/SAS • Rack Mount Kit (Industry 19" rack-mountable) NOTE: For an up to date list of compatible hardware, please visit the system’s support page on www.tyan.com Required Hardware Components (3) M1256T70-BP6-8 HDD BP M1702T70-USB (5) System fans M1807TA7-FB TYAN ® S8237 system board (pre-installed) (1+1), 750W power supply unit 30 (2) M2212-R16-2F Riser card M1701T70-FPB 2U barebone, (24) hot swap HDD bays 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 30 A B 1 31 35 30 29 28 27 7 8 9 10 11 2 3 4 5 6 C 26 25 24 23 D E F c a b 12 13 14 15 16 17 22 21 20 19 18 d e 34 3332 1 2 3 Install the Processor Open the socket lever. 1 Open the CPU socket cover. 2 Install the processor and make sure the gold arrow is located in the right direction. 4 5 Close the CPU socket cover. 3 Remove the CPU protective cap. 6 Close the socket lever. Loosen the 2 thumb screws on the back side. Take off the top cover. Take off the air duct. Preparing the Chassis Read normal ESD (Electrostatic Discharge) procedures. Place your TYAN ® Server Chassis on a flat anti-static surface to perform the following integration procedures. Read ESD procedures before reaching inside to install components. Open the Chassis Install the CPU Heatsink 1 Apply the thermal grease. 2 Install the CPU heatsink. 3 Secure the heatsink screws. Installing the Air Duct 1 Place the Air Duct onto the chassis. Installing the Add-On card (Optional) 2 Lift the riser bracket up. 5 Secure the add-on card onto the riser bracket. 4 Insert the add-on card onto the riser bracket. 3 Unscrew to remove the PCI bracket from the riser bracket. 1 Unscrew the riser card assembly. 7 Secure the add-on module to the chassis using a thumb screw. 6 Insert the riser bracket with the add-on module onto the chassis. NOTE: 1. Connect the add-on power cable to the connector of the add-on module. 2. There are two riser brackets inside the chassis. To install other add-on cards onto the riser brackets, please refer to the barebone user’s manual on our web site at http://www.tyan.com for more details. 1 2 3 Unlock the clips. Insert the memory module. Lock the clips. 1 Press the locking lever and pull the locking lever open. 2 Slide the HDD tray out. 3 Unscrew the HDD tray bracket. 4 Place a hard drive into the drive tray. Use four screws to secure the HDD. 5 Reinsert the HDD tray into the chassis. 6 Press the locking lever to secure the tray. Repeat the same procedures to install other HDD trays. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13 4 I/O Ports Ethernet (LAN3) USB2.0 Port USB2.0 Port shared with IPMI 16/17. 8-pin Power Connector (PWR3/PWR2) 18. 4-pin Power Connector (PW4) 19/20. Fan Connector (J23/J24) 21/22. Fan Connector (J21/J15) 23/24. Fan Connector (J14/J10) 25/26. Fan Connector (J9/J55) 27/28. 8-pin Power Connector (PWR5/PWR4) 29. Front Fan Header (J99) 30. Chassis Intrusion Header (JP16) 31. Front Panel Header (J64) 32. Super I/O ROM (U118) 33. USB Front Panel Header (J90) 34. Vertical Type-A USB Connector (USB0) 35. COM Header (J8) CPU 0 CPU 1 SR5670 SP5100
