DIN Rail Mounted Multi 9™ Surge Protective Devices
DIN Rail Mounted Multi 9™ Surge Protective Devices 6-5
Nipple Mounted Surge Protective Devices
HWA Series Non-Modular, Nipple Mounted Device 6-6
XW Series Non-Modular, Nipple Mounted Device 6-6
XR Series Nipple Mounted Surge Protective Device 6-6
LC Series In-Line Surge Protective Device and Noise Filter 6-7
Secondary Surge Arresters 6-7
Mounting Brackets 6-7
Residential Surge Protective Devices
Surgebreaker® Whole House Surge Protective Devices 6-8
Surgebreaker® Plus Low-Voltage Only Surge Suppressor 6-8
Surgebreaker® Plus Accessories 6-8
QO®, NQ, and Homeline® Panelboard Surge Arresters 6-8
New!
New!
New!
New!
New!
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Modular External SPDExternal Modular Assembly (EMA) SPD products feature a design based on modules for a flexible, cost effective way to achieve superior protection at every level of the electrical distribution system. Modularity means lower life cycle costs and fast, easy service or replacement.
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240b Can be used on 4-wire or 3-wire grounded neutral system.
( ) For option, select and add the appropriate suffix from the option listing below:
Non-Modular External SPDNon-modular External Brick Assembly (EBA) SPD products consist of a consolidation of phase modules into one solid “brick” casting and offered at a competitive price for those who want great protection on a limited budget.
a Can be used on 4 wire or 3 wire grounded neutral system.b 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
( ) For options, select and add the appropriate suffix from the option listing below:
10 Mode Modular External SPDThe 10-Mode (All Mode) SPD is an external modular parallel system that provides discrete surge suppression paths for all ten modes (L-L, L-N, L-G, N-G). Optional Sine Wave Tracker (SWT) circuitry establishes the power surge clamping window relative to the sine wave voltage to provide increased performance at distribution and branch panel applications.• 10 year product warranty• Audible alarm, dry contacts and surge counter are included in the standard
diagnostic package• Standard internal 200 kA IC fault rated fusing, 200 kA SCCR
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240( ) For option, select and add the appropriate suffix from the following listing:
High Resistance Ground (HRG) Modular External SPDThe Surgelogic® High Resistance Ground (HRG) SPD is an external modular parallel system that provides protection from transients referenced phase to phase and phase to ground and is designed specifically for HRG configured systems.
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
Option Descriptions• Integral Switch. The integral switch provides a mechanical means to
electrically isolate the entire surge suppressor before opening the enclosure door to facilitate servicing of the unit’s components.
• Remote Monitor. This option displays the alarm status of the surge protective device up to 1000 feet from the unit.
• Flush Mounting. Flush mounting collar can be used on 120–240 kA EMA and EBA series devices. Devices with integral switch require 20” flush mounting collar.
Surgelogic®
Surgelogic® Surge Protective Device (SPD) products offer the world’s finest array of solutions for electrical distribution systems. From simple to mission-critical applications in commercial, industrial, and OEM design, the comprehensive Surgelogic® line provides devices for every need.
Externally Mounted Surge Protective DevicesSurgelogic® offers a full range of externally mountable SPDs. These units are designed to provide protection against surges from service entrance panels down to point of use equipment.Listed to UL1449 Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009), and UL 1283 where applicable. Meets requirements of ANSI/IEEE C62.41.1, C62.41.2, and C62.45.
• 10 year product warranty• Standard product protection modes L-N, L-G, L-L, and N-G• Standard internal 200 kA AIC surge rated fusing, 200 kA SSCR
• Audible alarm with enable/disable switch, dry contacts, and surge counter standard
• Indicator LEDs; normal (green) and fault condition (red) for each phase
Table 6.1: EMA Series Modular Device
Service Voltage
Peak Surge Current Rating
per Phase(kA)
NEMA 1/3R/12 Cat. No. $ Price
NEMA 4X Stainless Steel
Cat. No. $ Price
Note: Supplied with audible alarm, alarm enable/disable switch, dry contacts, and surge counter.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Surge Protective Devices Replacement ModulesRefer to Catalog 6671CT9701
Replacement Modules
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240b High-leg delta (Phase B modules are different than Phase A and Phase C modules)
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240.
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
a 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Internally Mounted Surge Protective DevicesSurge protective devices installed internally or integral to systems for service entrance and branch panel protection against damaging surges. No SPDs in the industry that can compete with the performance of integrally/internally mounted products installed next to the supply busses inside Square D® systems. Built-in performance is the best way to ensure cost effective power quality (especially important for critical power facilities).
Internally Mounted—New ConstructionSurgelogic® SPD products with integral/internal performance make new construction projects easy with factory installed surge protection. Refer to the sections listed below to identify the correct product for your application or contact TVSS TAG at 1-800-577-7353 for assistance.
Busway—Refer to Section 12
Internally Mounted—RetrofitTo ensure high-performance surge protection at critical power locations, A variety of Surgelogic® products are offered which are designed specifically for retrofitting into commonly used Square D® systems. Retrofitting SPD units on I-Line, QMB, MCC, and Busway applications is simple. The QMB fusible switch, 6 in. MCC bucket, I-Line and Busway plug-on units come with the SPD factory-built into these devices.
• Meets requirements of CSA C22.2 No. 8-M1986• Audible alarm with enable/disable switch, dry contacts, and surge
counter standard.• Standard internal 200 k AIC surge rated fusing
• Standard internal 200 k AIC surge rated fusing• Short circuit current rating 200 kA• EMI/RFI filtering
Table 6.10: Internally Mounted—Retrofit
VoltageSurge
Current Rating
I-Line Branch Unitsb QMB Branch Unitsc Busway Units Model 6 MCC Unitse
a Can be used on 4-wire or 3-wire grounded neutral system.b Requires 13.5" mounting height.c Requires 9" mounting height.d 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
Note: If required, order remote monitor from page 6-2.
PanelboardsRefer to Section 9
NF NQ
Switchboards and SwitchgearRefer to Section 11
PZ4 QED
Motor ControlCenters Refer to
Section 17
Integrated Power andControl Centers
Refer to Section 10
MCC IPAC2
I-Line Surgelogic® SPD Unit
QMB Surgelogic SPD Unit
Busway Surgelogic SPD Unit
MCC Surgelogic SPD Unit
PE4 PE7 PE1A Discount Schedule
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Surge Protective Devices DIN Rail Mounted Multi 9™ Surge Protective DevicesRefer to Catalog 6671CT9701
Surgelogic OEM/Assembler KitSurgelogic® OEM/assembler kits allow manufacturers to add industry-leading surge protection directly to customized equipment. Manufacturers benefit from shorter wire lengths that optimize the clamping voltage of the SPD. Products come with a backplane-mounted SPD, mounting hardware and diagnostic display with 36" cables. Audible alarm, silence switch, remote monitoring contacts, and surge counter are standard.UL 1449 Recognized.
a Can be used on 4-wire or 3-wire grounded neutral system.b Note the last character of the catalog number is the letter “O”, not a zero.c 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
DIN Rail Mounted Multi 9™ Surge Protective DevicesMulti 9 SPDs offer a compact solution for protecting electronic equipment from the damaging effects of surges. These parallel, DIN-rail mountable, terminal-connected devices include 1-pole, 2-pole and 4-pole models with up to 80kA of surge protection. This product is ideal for control-panel manufacturers and electrical installers requiring integral power protection. They must be used in conjunction with the Multi 9 family of circuit breakers and supplementary protector products to provide safe, reliable, surge protectionUL, cUL, and IEC (CE Mark) listings to meet international requirements
• Designed for OEMs to protect electronic equipment from damaging surges• DIN rail mounting and compression terminals simplify installation • 1-pole, 2-pole and 4-pole with up to 80 kA surge current rating; 120 to 400 Vac• Status indication LED on all models• Thermally fused for added protection• Optional Form C dry contacts for remote monitoring• Used in conjunction with Multi 9 supplementary protectors—reference Table 6.12 below
OEM Kit
Table 6.11: OEM/Assembler KitsServiceVoltage
Peak Surge Current Ratingper Phase (kA) Cat. No.b $ Price
Note: Supplied with audible alarm, alarm enable/disable switch, dry contacts, and surge counter.
Table 6.12: DIN Rail Mounted Multi 9™ Surge Protective Devices
Service Voltage Number of Poles
Peak Surge Current
Dry Contacts Cat. No. Rating $ Price
Multi 9™ C60N Supplementary Protectors
1P 2P 3P 4P
120 V, Single Phase 1
20 kA No 12710 10 A, Curve B 94.00 MG24116 — — —
45 kANo 12713 20 A, Curve B 161.00 MG24119 — — —Yes 12714 20 A, Curve B 189.00 MG24119 — — —
65 kANo 12719 25 A, Curve B 243.00 MG24120 — — —Yes 12720 25 A, Curve B 269.00 MG24120 — — —
120/240 V, 1-phase, 3-wire 2
20 kA N/A 12725 10 A, Curve B 136.00 — MG24131 — —45 kA N/A 12727 20 A, Curve B 215.00 — MG24134 — —
208Y/120 V, 3-phase, 4-wire 4
20 kANo 12729 10 A, Curve B 269.00 — — MG24146 MG24161Yes 12730 10 A, Curve B 323.00 — — MG24146 MG24161
45 kANo 12733 20 A, Curve B 484.00 — — MG24149 MG24164Yes 12734 20 A, Curve B 538.00 — — MG24149 MG24164
80 kANo 12737 25 A, Curve C 660.00 — — MG24470 MG24487Yes 12738 25 A, Curve C 713.00 — — MG24470 MG24487
OE1A Discount Schedule
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Surge Protective DevicesRefer to Catalog 6671CT9701
HWA Series Non-Modular, Nipple-Mounted Surge Protective DeviceThe Surgelogic® HWA series surge protective device is a non-modular, nipple-mounted parallel connected surge protective device. A surge suppression path is provided for each mode, line-to-neutral (L–N), line-to-line (L–L), line-to ground (L–G), and neutral-to-ground (N–G). Each mode is individually fused and uses circuitry with thermal cutouts. On-line diagnostics continuously monitor the device status.Listed to CULUS 1449 Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009), and UL 1283 where applicable. Meets requirements of fourth edition CSA C22.2 No. 8-M1986.• Audible alarm indicates a fault condition• Compact design provides easy mounting inside or outside the equipment cabinets• Dry contacts• Does not contain alarm enable/disable switch
a Can be used on 4-wire or 3-wire grounded neutral system.b 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
XW Series Non-Modular, Nipple-Mounted Surge Protective DeviceThe XW Series SPD is a multi-phase surge suppressor rated at 100 kA per phase. It is compact and affordable and comes in a variety of voltage configurations, including Delta. The XW Series SPD is designed for use in industrial, commercial, and residential applications and comes standard in a NEMA 4 housing.Listed to UL 1449 Second Edition rev. 2/9/2007, cUL Listed, and CSA 22.2 No. 8-M1986.• Audible alarm indicates a fault condition• Compact design provides easy mounting inside or outside the equipment cabinets• Dry contacts• Does not contain alarm enable/disable switch
a MCOV = Maximum Continuous Operating Voltageb 480Y/277 series applies to the following voltages 380Y/220, 400Y/230, and 415Y/240
XR Series Nipple-Mounted Surge Protective DeviceThe XR Series SPD provides high-quality surge protection in a compact and versatile package. This product is ideal for panel builders as well as manufacturers and integrators of instrumentation cabinets for industrial, commercial, and residential applications for single-phase power systems.UL, cUL Listed, UL 1449 Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009), CSA 22.2 No. 8-M1986• 40 kA surge rating• Short circuit current rating 25 kA• NEMA 4X housing suitable for indoor or outdoor application• Audible alarm standard• Convenient back or side nipple mounting locations available
Table 6.13: HWA Series Non-Modular, Nipple-Mounted Surge Protective DeviceService Voltage
Peak Surge Current Rating per Phase (kA)
NEMA 3R, 4X, 12 Cat. No. $ Price
120/240 V,1-phase, 3-wire
+ground
50 TVS1HWA50X 1399.0080 TVS1HWA80X 1560.00
120 TVS1HWA12X 1995.00
208Y/120 V,3-phase, 4-wire
+ground a
50 TVS2HWA50X 1492.0080 TVS2HWA80X 1648.00
120 TVS2HWA12X 2118.00
120/240 V,3-phase, 4-wire +ground
High-leg Delta
50 TVS3HWA50X 1492.0080 TVS3HWA80X 1648.00
120 TVS3HWA12X 2118.00
480Y/277 V,3-phase, 4-wire
+ground ab
50 TVS4HWA50X 1549.0080 TVS4HWA80X 1705.00
120 TVS4HWA12X 2198.00
Table 6.14: XW Series Non-Modular, Nipple-Mounted DeviceService Voltage Surge Capacity MCOVa Cat. No. $ Price
120/240 V, 1-phase 100 kA/phase 150/300 V TVS1XW100C 1764.00208Y/120 V, 3-phase 100 kA/phase 300/150 V TVS2XW100C 1875.00240D/120 V, 3-phase 100 kA/phase 300/150 V TVS3XW100C 1875.00
480Y/277 V, 3-phaseb 100 kA/phase 640/320 V TVS4XW100C 2024.00480D V, 3-phase 100 kA/phase 640 V TVS5XW100C 2150.00240D V, 3-phase 100 kA/phase 300 V TVS6XW100C 1875.00
600Y/347 V, 3-phase 100 kA/phase 780/390 V TVS8XW100C 2024.00600D V, 1-phase 100 kA/phase 780 V TVS9XW100C 2150.00
Table 6.15: XR Series Nipple-Mounted Surge Protective DevicesService Voltage Mounting Method Cat. No. $ Price
120/240 V,1-phase, 3-wire +ground
Back Nipple TVS120XR40B 315.00Side Nipple TVS120XR40S 315.00
120 V,1-phase, 2-wire +ground
Back Nipple TVS120XRB 290.00Side Nipple TVS120XRS 324.00
230 V, 1-phase, 2-wire +ground
Back Nipple TVS230XR40B 347.00Side Nipple TVS230XR40S 347.00
Type HWA
Type XW
Type XR
DE2 Discount Schedule
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
LC Series In-Line Surge Protective Device and Noise FilterThe LC Series SPD offers high-quality surge protection and noise filtration for any microprocessor-based product, computer, analyzer, PLC, motion control system, original equipment manufacturer (OEM), or any sensitive single phase load. The LC can be connected to the incoming power source (20 A or less) to isolate the control cabinet from the outside environment. This product is ideal for panel builders as well as manufacturers and integrators of instrumentation cabinets for industrial, commercial, or residential applications. The LC uses a series/hybrid suppression circuit that delivers 40,000 peak amps of surge protection with true sine wave tracking protection up to -75 dB of noise filtration.UL 1449 Second Edition rev. 2/9/2007 330 Vac clamping rated. CURUS, CSA, and CE recognized, CSA C22.2 No. 0-M91, CSA C22.2 No. 8-M1986, CSA C22.2 No. 42-M1984, CSA C22.2 No. 21-M90• 40 kA surge rating• Short circuit current rating 10 kA maximum• Optional Form C dry contact status output• DIN rail or direct panel mounting• LED status indication• -75 db noise filtration sine wave tracking
a Optional Form C Dry Contact—Add “C” suffix to catalog number, e.g. TVS120LC5C. Option Price $60.00
Hard-Wired Secondary Surge ArrestersThe SDSA1175 Secondary Surge Arrester is designed and listed for indoor or outdoor installation and surge protection of single-phase three-wire 120/240 Vac 60 Hz electrical services and major appliances. Two SDSA1175 Secondary Surge Arresters can be installed to provide protection on 208Y/120 Vac three-phase four-wire services.The SDSA3650 Secondary Surge Arrester is designed and listed for indoor or outdoor installation and surge protection of three-phase grounded electrical services up to 600 Vac. and is used extensively in service entrance panels to provide an efficient and economical means of surge protection.CULUS secondary surge arresters. Meets ANSI/IEEE C62.11-1993 and meets requirements of NEC Article 285. SDSA3650 Listed to UL Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009).• Suitable for indoor and outdoor applications (NEMA 4X housing)• LED indicates operational status• SDSA1175 36 kA per phase• SDSA3650 40 kA per phase
b See Table 6.18 for QOSAMK mounting kit for installation in QO load centers.c Do not use on ungrounded systems. Systems must be solidly grounded.
Mounting Brackets for Nipple-Mounted DevicesThe nipple products shown in this catalog provide a convenient means of incorporating SPD protection within a new or existing cabinet. The mounting bracket (below) is designed for easy mounting of nipple products inside enclosures.
Table 6.16: LC Series In-Line Surge Protective Device and Noise FilterService Voltage Rated Load Current Cat. No.a $ Price
120 V, 1-phase
5 A TVS120LC5 255.0010 A TVS120LC10 282.0015 A TVS120LC15 308.0020 A TVS120LC20 330.00
230 V, 1-phase
5 A TVS230LC5 255.0010 A TVS230LC10 282.0015 A TVS230LC15 308.0020 A TVS230LC20 330.00
Type LC
Secondary Surge ArrestersThe Secondary Surge Arrester (SDSA) series products are designed primarily to protect against external surges at service entrance panels. They are designed and tested to be used on the line side or the load side of the main service disconnect switch. These devices may also be used for surge protection of irrigation pumps, oil pumps and motors operating below 600V.
Table 6.18: Mounting Bracket for EnclosuresDescription Cat. No. $ Price
Mounts to QO®, Homeline® Load Center and other enclosures QOSAMK 7.60
SDSA1175
SDSA3650
QOSAMK
DE1B Discount Schedule
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Surgebreaker® Plus Whole House Surge Protective DeviceThe Surgebreaker® Plus Whole House Surge Protector provides protection against electrical surges to AC power, telephone, and television cables. Installed next to your circuit breaker power panel, the device is hard-wired to the electrical panel and accommodates up to four telephone lines (eight with optional telco unit) and two 75 ohm coaxial television cable or satellite protection. The Surgebreaker® Plus device can be surface or flush mounted, depending on your power panel installation.Listed to UL 1449 Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009). Meets requirements of NEC® Article 285, ANSI/IEEE C62.41.1, C62.41.2, C62.45, and CSA C22.2 No. 8-M1986.• AC line protection single phase three wire—120/240 Vac• Four line telephone protection standard with tool-less insulation displacement connectors (IDC)• Two line coaxial protection for CATV standard• LED status indicator• Space for additional telephone protector• Space for additional coaxial protector (CATV or Satellite)• Modular design with optional accessories• 80 kA per phase AC protection
Surgebreaker® Plus Low-Voltage Only Surge Protective DeviceThe Surgebreaker® Plus Low Voltage Module provides protection against electrical surges to telephone, and television cables. Installed next to your Telephone and Cable entrance point. The device accommodates up to four telephone lines (eight with optional telco unit) and two 75 ohm coaxial television cable or satellite protection.Listed to UL 497 A and B.• Non-metallic NEMA 3R enclosure can be installed indoor or outdoor• Four line telephone protection standard with tool-less insulation displacement connectors (IDC)• Two line coaxial protection for CATV or satellite• Space for additional telephone protector• Space for additional coaxial protector • Modular design with optional accessories
Surgebreaker® Plus AccessoriesAdd additional protection or replace existing modules in any of the three Surgebreaker Plus products.
QO, NQ, and Homeline Panelboard Surge Protective DeviceThe Square D Surgebreaker® surge protective device is an easy to install plug-in unit that installs as quickly as a standard circuit breaker. The Surgebreaker® uses two pole spaces in a QO or Homeline loadcenter, or NQ panelboard.CULUS Listed secondary surge arrester, and Listed to UL 1449 Second Edition rev. 2/9/2007 (Third Edition effective 9/29/2009). Meets ANSI/IEEE C62.11-1993; CSA C22.2 No. 233.1-87, and NEC Article 285.• QO2175SB for QO® load centers and combination devices, NQ panelboards• HOM2175SB for Homeline® load centers and combination devices• Plug-on design requires two pole spaces• LED indicates operational status• 27 kA per phase AC protection
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
