ADD DIMENSIONS ON DATUM TARGETS B1/B2/C1 (SHEET 1). ADD MARKER TAPE SCALE INDEX W/END LIMITS & INDEX VIEWS AND NOTES. UPDATE END CAP/INDEX & LIMIT MARKERS/NOTES (PREVIOUSLY SHEET 3). ELIMINATE FIGURES. 1, 2, 3 & INSTALLATION NOTES (PREVIOUSLY SHEET4). CHANGE DRAWING DESCRIPTION IN TITLE BLOCK. 3 2360 SUBJECT TO CHANGE WITHOUT NOTIFICATION D C B A A B C D SCALE: SIZE DWG. NO. B SHEET 1 OF 4 REV. DATE APPROVALS DRAWN CHECKED ENGRG. MFG ENG UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN MILLIMETERS TOLERANCES ARE: 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 7/7/09 VB ADDED WIRE COLORS TO TABLES 2 & 3, MTG PLATE REC. UPDATED ADDRESS. OF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp. REVISIONS LTR DESCRIPTION DATE APPROVED DIM. APPLY AFTER PROCESSING INTERPRET ALL GEOMETRIC TOLS. PER ANSI Y14.5M-1994 7/28/08 VB DECIMALS: ANGULAR: NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE .XX ± .13 30 MIN. ECO .X ± .25 PROJECTION DESCRIPTION: CAD FILE: 1 2 2121 MicroE Systems Division of GSI Group Bedford, MA 01730 TAPE/MARKER TAPE SCALES THIS APPLIES TO QUADRATURE SENSOR ONLY. INITIAL 1 ---- 7/23/08 A.GOLDMAN UNITS: mm 6. QA 3rd ANGLE THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALL SENSOR, OUTPUT SIGNAL A+ (PIN 14) LEADS OUTPUT SIGNAL B+ (PIN 13). MERCURY II 5000 SENSOR ID-00353 3 S.BUTURLIA 7/10/08 DIRECTION "A" NOTES: 1. RECOMMENDED MOUNTING HARDWARE: 2-56 or M2.5 SOCKET HEAD CAP SCREWS 2. IF BENCHING PINS ARE TO BE USED, PINS MUST BE PLACED ALONG DATUM EDGES OF SENSOR FOR PROPER ALIGNMENT. (REFERENCE DATUMS B1,B2 AND C1). 3. HEIGHT OF SENSOR BENCHING PINS MUST NOT EXCEED HEIGHT OF SENSOR BODY (4.70mm). 4. RECOMMENDED SENSOR MOUNTING PLATE THICKNESS: MINIMUM: 4 SCREW THREADS MAXIMUM: ALLOW FOR CLEARANCE TO SCALE AND SCALE MOUNTING HARDWARE (BENCHING SURFACES, TRENCHES, ETC.) 5. SEE SHEETS 3 AND 4 FOR DIMENSIONS AND LOCATIONS OF REFERENCE MARKERS. 6. WHEN SCALE MOVES IN DIRECTION "A" WITH RESPECT TO A STATIONARY INTERFACE, ENCODER, 20um, 125 Middlesex Tpk. 6/27/11 SB B C REFERENCE MARKER REGION 5. D 8.60 6.00 SENSOR MOUNTING PLATE RECOMMENDATION 1.59 4x R ±0.08 ±0.08 33.00 3.10 27.42 7.50 3.50 14.50 THRU. 2X M2.5 or 2-56UNC-2B A 4.70 2X 5.38 ADHESIVE BACKING METAL TAPE SCALE OUT OF OPERATING RANGE FOR CLARITY TAPE SCALE SHOWN IN THIS VIEW TRANSLATED IN X-AXIS C L OPTICAL B C 3.00 4X R 2.39 0.76 4X R 13.50 26.42 33.00 38.50 7.50 5.33 2.35 15.88 2X 2.79 THRU. TAPE SCALE MOUNTING SURFACE SENSOR MOUNTING SURFACE A 2.03 9.0 4.70 0.29 3.38 B2 C C1 B B1 6.75 2.35 33.00
Transcript
ADD DIMENSIONS ON DATUM TARGETS B1/B2/C1 (SHEET 1). ADD MARKER TAPE SCALE INDEX W/END LIMITS & INDEX VIEWS AND NOTES. UPDATE ENDCAP/INDEX & LIMIT MARKERS/NOTES (PREVIOUSLY SHEET 3). ELIMINATE FIGURES. 1, 2, 3 & INSTALLATION NOTES (PREVIOUSLY SHEET4). CHANGE DRAWING DESCRIPTION IN TITLE BLOCK.
3 2360
SUBJECT TO CHANGE WITHOUT NOTIFICATION
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 1 OF 4
REV.
DATEAPPROVALS
DRAWN
CHECKED
ENGRG.
MFG ENG
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS ARE IN MILLIMETERS
OF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
REVISIONS
LTR DESCRIPTION DATE APPROVED
DIM. APPLY AFTER PROCESSINGINTERPRET ALL GEOMETRIC TOLS.
PER ANSI Y14.5M-1994
7/28/08 VB
DECIMALS: ANGULAR:
NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE
.XX ± .1330 MIN.
ECO
.X ± .25
PROJECTION
DESCRIPTION:
CAD FILE:
1
2 2121
MicroE SystemsDivision of GSI Group
Bedford, MA 01730
TAPE/MARKER TAPE SCALES
THIS APPLIES TO QUADRATURE SENSOR ONLY.
INITIAL1 ----
7/23/08A.GOLDMAN
UNITS: mm
6.
QA
3rd ANGLE
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALL
SENSOR, OUTPUT SIGNAL A+ (PIN 14) LEADS OUTPUT SIGNAL B+ (PIN 13).
MERCURY II 5000 SENSOR
ID-00353 3
S.BUTURLIA 7/10/08
DIRECTION "A"
NOTES: 1. RECOMMENDED MOUNTING HARDWARE: 2-56 or M2.5 SOCKET HEAD CAP SCREWS
2. IF BENCHING PINS ARE TO BE USED, PINS MUST BE PLACED ALONG DATUM EDGES OF SENSOR FOR PROPER ALIGNMENT. (REFERENCE DATUMS B1,B2 AND C1).
3. HEIGHT OF SENSOR BENCHING PINS MUST NOT EXCEED HEIGHT OF SENSOR BODY (4.70mm).
4. RECOMMENDED SENSOR MOUNTING PLATE THICKNESS: MINIMUM: 4 SCREW THREADS MAXIMUM: ALLOW FOR CLEARANCE TO SCALE AND SCALE MOUNTING HARDWARE (BENCHING SURFACES, TRENCHES, ETC.)
5. SEE SHEETS 3 AND 4 FOR DIMENSIONS AND LOCATIONS OF REFERENCE MARKERS.
6. WHEN SCALE MOVES IN DIRECTION "A" WITH RESPECT TO A STATIONARY
INTERFACE, ENCODER, 20um,
125 Middlesex Tpk.
6/27/11 SB
B
CREFERENCE MARKERREGION
5.
D
8.60
6.00
SENSOR MOUNTING PLATE RECOMMENDATION
1.594x R
±0.08
±0.0833.00
3.10
27.42
7.50
3.50
14.50
THRU. 2X
M2.5 or 2-56UNC-2B
A
4.70
2X 5.38
ADHESIVE BACKING
METAL TAPE SCALE
OUT OF OPERATING RANGE FOR CLARITYTAPE SCALE SHOWN IN THIS VIEW TRANSLATED IN X-AXIS
CLOPTICAL
B
C
3.00
4X R2.39
0.764X R
13.50
26.42
33.00
38.50
7.50
5.33
2.35
15.88
2X 2.79 THRU.
TAPE SCALE MOUNTING SURFACE
SENSOR MOUNTING SURFACE
A
2.03
9.0
4.70
0.293.38
B2
C
C1
B
B1
6.75
2.35
33.00
PIN 1
PIN 8PIN 15
PIN 9
SEE TABLE 2 and 3 FORPIN FUNCTIONS
IDENTIFICATION LABELSENSOR P/N, SERIAL#
IDENTIFICATION LABELINTERPOLATION SETTINGS
15.7
4.7
4.2 CABLEDIAMETER
+.013M/-0.0CABLE LENGTH
51.9
39.2
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 2 OF 4
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
TABLE 2. TABLE 3.
ID-00353 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
MicroE SystemsDivision of GSI GroupTABLE 1.
INTERFACE, ENCODER, 20um,TAPE/MARKER TAPE SCALES
MERCURY II 5000 SENSOR
NOTE: GND AND INNER SHIELD ARE INTERNALLY CONNECTED.
3.2
Cable Lengths
1 Meter
3 Meter
5 Meter
Custom
Pin Wire color Function
1 Brown RL+
2 Black GND
3 White RL-
4 White I-
5 White B-
6 White A-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray LL+
11 White LL-
12 Green I+
13 Blue B+
14 Violet A+
15 Black DO NOT CONNECT
Mercury II 5000 15-Plug Quadrature Output
Mercury II 5000 15-Plug Serial Output
Pin Wire color Function
1 Brown nCS+
2 Black GND
3 White nCS-
4 White DIAG_IN_OUT-
5 White SCLOCK_OUT-
6 White SDATA_OUT-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray SCLOCK_IN+
11 White SCLOCK_IN-
12 Green DIAG_IN_OUT+
13 Blue SCLOCK_OUT+
14 Violet SDATA_OUT+
15 Black DO NOT CONNECT
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 3 OF 4
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
ID-00353 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
NOTES:
1. MARKER TAPE SCALES CAN BE SUPPLIED IN INDIVIDUAL PIECES OR IN CONTINUOUS FORM.
2. END CAPS ARE OPTIONAL. IF USED, RECOMMENDED MINIMUM EXPOSED LENGTH OF END LIMITS IS 5 mm (SEE INSTALLATION MANUAL), AND ADDITIONAL TAPE LENGTH MAY BE REQUIRED BASED ON APPLICATION (SEE SHEET 4).
3. REFERENCE MARKERS (STICK-ONS) CANNOT BE USED ON MARKER TAPE.
4. FOR ALTERNATE MARKER LOCATIONS OR LENGTHS, MULTIPLE INDEXES OR ADDITONAL FEATURES, CONTACT MICROE SYSTEMS.
5. FOR MOUNTING REQUIREMENTS IN TAPE SCALE APPLICATIONS, REFERENCE INTERFACE DRAWING ID-00379.
INTERFACE, ENCODER, 20um,TAPE/MARKER TAPE SCALES
MERCURY II 5000 SENSOR
LEFT LIMIT
INDEX w/END LIMITS
INDEX
MAIN PATTERN
RIGHT LIMITD
20.0
MARKER TAPE SCALE LENGTH (ML + 40 mm)
MEASURING LENGTH (ML)
20.00
6.00
ML/2
INDEX
INDEX
MAIN PATTERN
D
6.00
5.00
MEASURING LENGTH (ML)
ML/25.00
MARKER TAPE SCALE LENGTH (ML + 10 mm)
END CAP
26.00
10.40
LEFT/RIGHT LIMIT MARKER
20.00
2.00INDEX MARKER
16.00
8.00
2.00
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 4 OF 4
REV.
12345678
8 7 6 5 4 3 2 1
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
3ID-00353
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
NOTES:
1. BEFORE PLACING INDEX MARKERS, LIMIT MARKERS AND END CAPS, REMOVE PROTECTIVE FILM FROM TAPE SCALE.
2. NOTE DATUM EDGE OF TAPE SCALE AND REFERENCE MARKER REGION BEFORE APPLYING MARKERS.
3. MINIMUM MEASURING LENGTH SHOWN. ACTUAL MEASURING LENGTH MAY BE GREATER.
4. END CAPS, INDEX AND LIMIT MARKERS ARE OPTIONAL (SEE INSTALLATION MANUAL). WHEN NO LIMITS OR END CAPS ARE USED, RECOMMENDED TAPE SCALE LENGTH = MEASURING LENGTH + 10 mm.
5. LIMIT MARKERS CAN BE PLACED AT ENDS OF THE TAPE SCALE WHEN END CAPS ARE NOT USED.
6. END CAPS, INDEX AND LIMIT MARKERS SHALL NOT OVERLAP (WILL CAUSE INTERFERENCE WITH SENSOR).
7. FOR OTHER LENGTHS OF REFERENCE MARKERS, CONTACT MICROE SYSTEMS.
8. FOR MOUNTING REQUIREMENTS IN TAPE SCALE APPLICATIONS, REFERENCE INTERFACE DRAWING ID-00379.
INTERFACE, ENCODER, 20um,TAPE/MARKER TAPE SCALES
MERCURY II 5000 SENSOR
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
END CAP
LEFT LIMITMARKER
INDEX MARKER
RIGHT LIMITMARKER END CAP
13
TAPE SCALE LENGTH (ML + 66 mm)
20
13
20
MEASURING LENGTH (ML) 3.
A
4.70
2X 5.38
SCALE PATTERNSURFACE
SCALE MOUNTING SURFACE
SENSOR MOUNTING SURFACE
A2.03
9.0
4.70
2.49±0.10
5.42
CLOPTICAL
B
C
3.00
4X R2.39
0.764X R
13.50
26.42
33.00
38.50
7.50
5.33
2.35
15.88
2X 2.79 THRU.
SENSOR MOUNTING PLATE RECOMMENDATION
1.594x R
±0.08
±0.0833.00
3.10
27.42
7.50
3.50
14.50
THRU. 2X
M2.5 or 2-56UNC-2B
B
REGION
C REFERENCE MARKER
6. D8.60
6.00
125 Middlesex Tpk.
CHANGE DRAWING DESCRIPTION IN TITLE BLOCK.
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 1 OF 3
REV.
DATEAPPROVALS
DRAWN
CHECKED
ENGRG.
MFG ENG
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS ARE IN MILLIMETERS
TOLERANCES ARE:
12345678
8 7 6 5 4 3 2
INITIAL
SUBJECT TO CHANGE WITHOUT NOTIFICATION
OF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
REVISIONS
LTR DESCRIPTION DATE APPROVED
DIM. APPLY AFTER PROCESSINGINTERPRET ALL GEOMETRIC TOLS.
PER ANSI Y14.5M-1994
3 2360
DECIMALS: ANGULAR:
NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALL
7. WHEN SCALE MOVES IN DIRECTION "A" WITH RESPECT TO A STATIONARY MERCURY II 5000 SENSOR
ID-00354 3
S.BUTURLIA
7/11/08
SENSOR, OUTPUT SIGNAL A+ (PIN 14) LEADS OUTPUT SIGNAL B+ (PIN 13). THIS APPLIES TO QUADRATURE SENSOR ONLY.
SHORT LINEAR SCALE INTERFACE, ENCODER, 20um,
w/ STICK-ON INDEX AND LIMITS,
DIRECTION "A"
7.
NOTES: 1. RECOMMENDED MOUNTING HARDWARE: 2-56 or M2.5 SOCKET HEAD CAP SCREWS
2. IF BENCHING PINS ARE TO BE USED, PINS MUST BE PLACED ALONG DATUM EDGES OF SENSOR FOR PROPER ALIGNMENT. (REFERENCE DATUMS B1,B2 AND C1).
3. HEIGHT OF SENSOR BENCHING PINS MUST NOT EXCEED HEIGHT OF SENSOR BODY (4.70mm).
4. HEIGHT OF SCALE BENCHING PINS NOT TO EXCEED THE THICKNESS OF THE SCALE.
5. RECOMMENDED SENSOR MOUNTING PLATE THICKNESS: MINIMUM: 4 SCREW THREADS MAXIMUM: ALLOW FOR CLEARANCE TO SCALE AND SCALE MOUNTING HARDWARE (BENCHING SURFACES, TRENCHES, ETC.)
6. SEE SHEET 3 FOR DIMENSIONS AND LOCATIONS OF REFERENCE MARKERS.
UPDATE INDEX AND LIMIT MARKERS AND NOTES. 6/27/11 SB
OUT OF OPERATING RANGE FOR CLARITYLINEAR GLASS SCALE SHOWN IN THIS VIEW TRANSLATED IN X-AXIS
B2
C
C1
B
B1
33.002.35
6.75
4.2 CABLEDIAMETER
+.013M/-0.0CABLE LENGTH
51.9
39.2
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 2 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
TABLE 2. TABLE 3.
ID-00354 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
TABLE 1.
INTERFACE, ENCODER, 20um,SHORT LINEAR SCALE
w/ STICK-ON INDEX AND LIMITS,MERCURY II 5000 SENSORNOTE: GND AND INNER SHIELD ARE INTERNALLY CONNECTED.
PIN 1
PIN 8PIN 15
PIN 9
SEE TABLE 2 and 3 FORPIN FUNCTIONS
IDENTIFICATION LABELSENSOR P/N, SERIAL#
IDENTIFICATION LABELINTERPOLATION SETTINGS
15.7
4.7
3.2
Cable Lengths
1 Meter
3 Meter
5 Meter
Custom
Pin Wire color Function
1 Brown RL+
2 Black GND
3 White RL-
4 White I-
5 White B-
6 White A-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray LL+
11 White LL-
12 Green I+
13 Blue B+
14 Violet A+
15 Black DO NOT CONNECT
Mercury II 5000 15-Plug Quadrature Output
Mercury II 5000 15-Plug Serial Output
Pin Wire color Function
1 Brown nCS+
2 Black GND
3 White nCS-
4 White DIAG_IN_OUT-
5 White SCLOCK_OUT-
6 White SDATA_OUT-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray SCLOCK_IN+
11 White SCLOCK_IN-
12 Green DIAG_IN_OUT+
13 Blue SCLOCK_OUT+
14 Violet SDATA_OUT+
15 Black DO NOT CONNECT
LEFT/RIGHT LIMIT MARKER
20.00
2.00INDEX MARKER
16.00
8.00
2.00
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 3 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
ID-00354 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
MicroE SystemsDivision of GSI Group
INTERFACE, ENCODER, 20um,SHORT LINEAR SCALE
w/ STICK-ON INDEX AND LIMITS,MERCURY II 5000 SENSOR
NOTES:
1. APPLICABLE LINEAR GLASS SCALE LENGTHS 70-130 mm. FOR SCALE LENGTHS SHORTER THAN 70 mm, CONTACT MICROE SYSTEMS.
2. MINIMUM MEASURING LENGTH SHOWN. ACTUAL MEASURING LENGTH MAY BE GREATER.
3. NOTE DATUM EDGE OF GLASS SCALE AND REFERENCE MARKER REGION BEFORE APPLYING MARKERS.
4. INDEX AND LIMIT MARKERS ARE OPTIONAL (SEE INSTALLATION MANUAL). WHEN NO LIMITS ARE USED, RECOMMENDED SCALE LENGTH = MEASURING LENGTH + 5 mm.
5. INDEX AND LIMIT MARKERS SHALL NOT OVERLAP EACH OTHER (WILL CAUSE INTERFERENCE WITH SENSOR).
6. FOR OTHER LENGTHS OF REFERENCE MARKERS, CONTACT MICROE SYSTEMS.
7. INDEX AND LIMIT MARKERS MAY BE PRINTED ON GLASS SCALES AT LOCATIONS SPECIFIED BY THE CUSTOMER. CONTACT MICROE SYSTEMS FOR DETAILS.
LEFT LIMIT MARKER
INDEX MARKER
RIGHT LIMIT MARKER
D 20
MEASURING LENGTH (ML) 2.
20
SCALE LENGTH (ML + 40 mm)
A
4.70
2X 5.38
OUT OF OPERATING RANGE FOR CLARITYLINEAR GLASS SCALE SHOWN IN THIS VIEW TRANSLATED IN X-AXIS
CLOPTICAL
B
C
3.00
4X R2.39
0.764X R
13.50
26.42
33.00
38.50
7.50
5.33
2.35
15.88
2X 2.79 THRU.
B
C1
B2
C
B1
33.00
2.35
6.75B
SENSOR MOUNTING SURFACE
6.
CREFERENCE MARKERREGION D
20.00
8.60
CHANGE DRAWING DESCRIPTION IN TITLE BLOCK.
SUBJECT TO CHANGE WITHOUT NOTIFICATION
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 1 OF 3
REV.
DATEAPPROVALS
DRAWN
CHECKED
ENGRG.
MFG ENG
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS ARE IN MILLIMETERS
TOLERANCES ARE:
12345678
8 7 6 5 4 3 2
125 Middlesex Tpk.
INITIALOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
REVISIONS
LTR DESCRIPTION DATE APPROVED
DIM. APPLY AFTER PROCESSINGINTERPRET ALL GEOMETRIC TOLS.
PER ANSI Y14.5M-1994
3 2360
DECIMALS: ANGULAR:
NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALL
7. WHEN SCALE MOVES IN DIRECTION "A" WITH RESPECT TO A STATIONARY MERCURY II 5000 SENSOR
ID-00355 3
S.BUTURLIA
7/11/08
SENSOR, OUTPUT SIGNAL A+ (PIN 14) LEADS OUTPUT SIGNAL B+ (PIN 13). THIS APPLIES TO QUADRATURE SENSOR ONLY.
LONG LINEAR SCALE INTERFACE, ENCODER, 20um,
w/ STICK-ON INDEX AND LIMITS,
DIRECTION "A"
7.
NOTES: 1. RECOMMENDED MOUNTING HARDWARE: 2-56 or M2.5 SOCKET HEAD CAP SCREWS.
2. IF BENCHING PINS ARE TO BE USED, PINS MUST BE PLACED ALONG DATUM EDGES OF SENSOR FOR PROPER ALIGNMENT. (REFERENCE DATUMS B1,B2 AND C1).
3. HEIGHT OF SENSOR BENCHING PINS MUST NOT EXCEED HEIGHT OF SENSOR BODY (4.70mm).
4. HEIGHT OF SCALE BENCHING PINS NOT TO EXCEED THE THICKNESS OF THE SCALE.
5. RECOMMENDED SENSOR MOUNTING PLATE THICKNESS: MINIMUM: 4 SCREW THREADS MAXIMUM: ALLOW FOR CLEARANCE TO SCALE AND SCALE MOUNTING HARDWARE (BENCHING SURFACES, TRENCHES, ETC.)
6. SEE SHEET 3 FOR DIMENSIONS FOR LOCATIONS OF REFERENCE MARKERS.
UPDATE INDEX AND LIMIT MARKERS AND NOTES. 6/27/11 SB
SENSOR MOUNTING PLATE RECOMMENDATION
1.594x R
±0.08
±0.0833.00
3.10
27.42
7.50
3.50
14.50
THRU. 2X
M2.5 or 2-56UNC-2B
SCALE PATTERNSURFACE
SCALE MOUNTING SURFACE
A2.03
5.42
9.0
4.70
2.49±0.10
IDENTIFICATION LABELSENSOR P/N, SERIAL#
IDENTIFICATION LABELINTERPOLATION SETTINGS
15.7
4.7
PIN 1
PIN 8PIN 15
PIN 9
SEE TABLE 2 and 3 FORPIN FUNCTIONS
4.2 CABLEDIAMETER
+.013M/-0.0CABLE LENGTH
51.9
39.2
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 2 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
TABLE 2. TABLE 3.
ID-00355 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
TABLE 1.
INTERFACE, ENCODER, 20um,LONG LINEAR SCALE
w/ STICK-ON INDEX AND LIMITS,MERCURY II 5000 SENSORNOTE: GND AND INNER SHIELD ARE INTERNALLY CONNECTED.
3.2
Cable Lengths
1 Meter
3 Meter
5 Meter
Custom
Pin Wire color Function
1 Brown RL+
2 Black GND
3 White RL-
4 White I-
5 White B-
6 White A-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray LL+
11 White LL-
12 Green I+
13 Blue B+
14 Violet A+
15 Black DO NOT CONNECT
Mercury II 5000 15-Plug Quadrature Output
Mercury II 5000 15-Plug Serial Output
Pin Wire color Function
1 Brown nCS+
2 Black GND
3 White nCS-
4 White DIAG_IN_OUT-
5 White SCLOCK_OUT-
6 White SDATA_OUT-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray SCLOCK_IN+
11 White SCLOCK_IN-
12 Green DIAG_IN_OUT+
13 Blue SCLOCK_OUT+
14 Violet SDATA_OUT+
15 Black DO NOT CONNECT
LEFT LIMIT MARKER RIGHT LIMIT MARKER
INDEX MARKER
MAIN PATTERN
D
SCALE LENGTH (ML + 40 mm)
MEASURING LENGTH (ML) 2.
20 20
LEFT/RIGHT LIMIT MARKER
20.00
2.00
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 3 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
ID-00355 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
NOTES:
1. APPLICABLE LINEAR GLASS SCALE LENGTHS 131-1000 mm. FOR SCALE LENGTHS LONGER THAN 1000 mm, CONTACT MICROE SYSTEMS.
2. MINIMUM MEASURING LENGTH SHOWN. ACTUAL MEASURING LENGTH MAY BE GREATER.
3. NOTE DATUM EDGE OF GLASS SCALE AND REFERENCE MARKER REGION BEFORE APPLYING MARKERS.
4. INDEX AND LIMIT MARKERS ARE OPTIONAL (SEE INSTALLATION MANUAL). WHEN NO LIMITS ARE USED, RECOMMENDED SCALE LENGTH = MEASURING LENGTH + 5 mm.
5. INDEX AND LIMIT MARKERS SHALL NOT OVERLAP EACH OTHER (WILL CAUSE INTERFERENCE WITH SENSOR).
6. FOR OTHER LENGTHS OF REFERENCE MARKERS, CONTACT MICROE SYSTEMS.
7. INDEX AND LIMIT MARKERS MAY BE PRINTED ON GLASS SCALES AT LOCATIONS SPECIFIED BY THE CUSTOMER. CONTACT MICROE SYSTEMS FOR DETAILS.
INTERFACE, ENCODER, 20um,LONG LINEAR SCALE
w/ STICK-ON INDEX AND LIMITS,MERCURY II 5000 SENSOR
INDEX MARKER
16.00
8.00
2.00
B2
B
B1
C
C1
33.002.35
6.75
125 Middlesex Tpk.
SCALE/HUB TABLE FROM SHEET 1 TO SHEET 3 & ADD COLUMN "DIM.J".
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 1 OF 3
REV.
DATEAPPROVALS
DRAWN
CHECKED
ENGRG.
MFG ENG
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS ARE IN MILLIMETERS
TOLERANCES ARE:
12345678
8 7 6 5 4 3 2
INITIAL
SUBJECT TO CHANGE WITHOUT NOTIFICATION
UNITS: mm
OF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
REVISIONS
LTR DESCRIPTION DATE APPROVED
DIM. APPLY AFTER PROCESSINGINTERPRET ALL GEOMETRIC TOLS.
PER ANSI Y14.5M-1994
3 2360
DECIMALS: ANGULAR:
NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALL
THIS APPLIES TO QUADRATURE SENSOR ONLY.
MERCURY II 5000 SENSOR
ID-00356 3
S.BUTURLIA
5.
7/11/08
6. SEE SHEET 3 FOR DIMENSIONS OF ROTARY SCALE AND HUB.
INTERFACE, ENCODER, 20um,
OUTPUT SIGNAL B+ (PIN 13).
NOTES: 1. RECOMMENDED MOUNTING HARDWARE: 2-56 or M2.5 SOCKET HEAD CAP SCREWS
2. IF BENCHING PINS ARE TO BE USED, PINS MUST BE PLACED ALONG DATUM EDGES OF SENSOR FOR PROPER ALIGNMENT. (REFERENCE DATUMS B1,B2 AND C1).
3. HEIGHT OF SENSOR BENCHING PINS MUST NOT EXCEED HEIGHT OF SENSOR BODY (4.70mm).
4. RECOMMENDED SENSOR MOUNTING PLATE THICKNESS: MINIMUM: 4 SCREW THREADS MAXIMUM: ALLOW FOR CLEARANCE TO SCALE AND SCALE MOUNTING HARDWARE (BENCHING SURFACES, TRENCHES, ETC.)
5. WHEN SCALE MOVES IN DIRECTION "A" WITH RESPECT TO A STATIONARY SENSOR, OUTPUT SIGNAL A+ (PIN 14) LEADS
CHANGE DRAWING DESCRIPTION IN TITLE BLOCK. ADD SHEET 3 AND MOVE 6/27/11 SB
SCALE MOUNTING SURFACE
SENSOR MOUNTING SURFACE
A
2.67
2.93
9.0
4.70
±0.102.29
H
A
4.70
5.38
SENSOR MOUNTING PLATE RECOMMENDATION
1.594x R
±0.08
±0.0833.00
3.10
27.42
7.50
3.50
14.50
THRU. 2X
M2.5 or 2-56UNC-2B
CLOPTICAL
B
C
3.00
4X R2.39
0.764X R
13.50
26.42
33.00
38.50
7.50
5.33
2.35
15.88
2X 2.79 THRU.
MAIN PATTERN
E
B
MACHINE AXIS
C
C
15.88±0.076
PIN 1
PIN 8PIN 15
PIN 9
SEE TABLE 2 and 3 FORPIN FUNCTIONS
IDENTIFICATION LABELSENSOR P/N, SERIAL#
IDENTIFICATION LABELINTERPOLATION SETTINGS
15.7
4.7
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 2 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
DESCRIPTION:
TABLE 2. TABLE 3.
ID-00356 3
UNITS: mm
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
TABLE 1.
INTERFACE, ENCODER, 20um,ROTARY SCALE w/ HUB,
MERCURY II 5000 SENSOR
NOTE: GND AND INNER SHIELD ARE INTERNALLY CONNECTED.
4.2 CABLEDIAMETER
+.013M/-0.0CABLE LENGTH
51.9
39.2
3.2
Cable Lengths
1 Meter
3 Meter
5 Meter
Custom
Mercury II 5000 15-Plug Serial Output
Pin Wire color Function
1 Brown nCS+
2 Black GND
3 White nCS-
4 White DIAG_IN_OUT-
5 White SCLOCK_OUT-
6 White SDATA_OUT-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray SCLOCK_IN+
11 White SCLOCK_IN-
12 Green DIAG_IN_OUT+
13 Blue SCLOCK_OUT+
14 Violet SDATA_OUT+
15 Black DO NOT CONNECT
Pin Wire color Function
1 Brown RL+
2 Black GND
3 White RL-
4 White I-
5 White B-
6 White A-
7 Red 5V
8 Red 5V
9 Black GND
10 Gray LL+
11 White LL-
12 Green I+
13 Blue B+
14 Violet A+
15 Black DO NOT CONNECT
Mercury II 5000 15-Plug Quadrature Output
D
C
B
A
A
B
C
D
SCALE:
SIZE DWG. NO.
BSHEET 3 OF 3
REV.
12345678
8 7 6 5 4 3 2 1
THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF MicroE Systems Corp. AND SHALLNOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALEOF APPARATUS WITHOUT EXPRESS WRITTEN AUTHORIZATION FROM MicroE Systems Corp.
CAD FILE: 3rd ANGLEPROJECTION
3
DESCRIPTION:
125 Middlesex Tpk.Bedford, MA 01730
Division of GSI GroupMicroE Systems
INTERFACE, ENCODER, 20um,ROTARY SCALE w/ HUB,
MERCURY II 5000 SENSOR
ID-00356
UNITS: mm
NOTES: 1. FOR ADDITIONAL PRINTED ON FEATURES (LIMITS) AND CUSTOM SIZES AND COUNTS, CONTACT MICROE SYSTEMS.
SCALE/HUB IDENTIFICATION AND SIZE
2.29
H
MAIN PATTERN(COUNTS/REV.)
REFERENCE/INDEXPATTERN
C
B
D
A
J
ON A BOLT CIRCLE G
EMOUNTING HOLE and
THREAD F. EQ. SPACED
Scale/Hub Counts/ Dim. A Scale I.D. Dim. B Dim. C Dim D. Dim E. Thread F Dim G. Dim. H Dim. J
