TC1191

8/12/2019 TC1191

1/31

Cameron Ball ValvesValves For Pipelines and the Oil and Gas Industries

8/12/2019 TC1191

2/31

How To Order Cameron Ball ValvesHow To Order Cameron Ball Valves

Classification Pressure Opening End Operator TrimClass Connection

80 ANSI 01 ANSI 150 0 Full 1 RF/RF 1A Lever 1 Standard

81 API 03 ANSI 300 7 Reduced 2 WE/WE 1A Extensions Lever 2 Standard (API)

82 AFNOR 04 ANSI 400 4 Venturi 3 RF/WE 2A Worm Gear 1 4 Hi Temp Teflon (150-600)

83 DIN 06 ANSI 600 9 All Others 4 RTJ/RTJ 2A Extension Worm Gear-1 8 Lo-Temp Nylon (150-600)

84 UNI 09 ANSI 900 5 RTJ/WE 3A Worm Gear-2 123 Pressure Regulating (150-1500)

15 ANSI 1500 9 All Others 3A Extension Worm Gear-2 212 NACE/(150-2500)

25 ANSI 2500 7A Direct Stem 213 NACE/(960-5000)

20 API 2000 7A Extension Direct Stem 214 Tefzel/NACE (150-1500)

30 API 3000 8A Worm Gear-1/Adapted 215 Tefzel/NACE (960-5000)

50 API 5000 8A Extension Worm Gear- 216 NACE/Lo Temp (150-2500)

1/Adapted 217 NACE/Lo-Temp (960-5000)

9A Worm Gear-2/Adapted 222 NACE/Hi-Temp (150-600)

9A Extension Worm Gear- 259 NACE/316 Inlay (150-2500)

2/Adapted

22A Square

22A Extension Square

Nut/Mtg/Flg

23A Worm Gear W/2

Square Operating Nut

23A Worm Gear with Right

Angle Pinion Shaft

Extension and 2

Square Operating Nut

1. Valve figure number.(See chart below.)

2. End and bore sizes.

3. Pressure classification.(ANSI 600 lb, API 3000 psi)

4. Type of end connections.(unequal ends can be furnished.)For weld end valves, specify I.D. orO.D., wall thickness and grade of pipe.

5. Type of operator.

6. Stem extension, if desired.Specify distance from valve centerlineto center of handwheel, or top ofpower operator mounting flange.

7. Type of trim or application.

8. Accessories, if desired.(lifting eyes, locking devices, etc.)Handwheels are included with valves,but operating levers must be orderedseparately.

Information on special trims and APIconfigurations is available upon request.

1. Valve size and pressure class and, iffor field conversion, the presentoperator.

2. Maximum differential pressure acrossvalve during operation and anyabnormal operating conditions.

3. Speed of opening and closing,probably frequency of operation.

4. Type operator desired.(electric, hydraulic, pneumatic.)

5. Information on operating medium.If electric: voltage, frequency, single orthree phase, open or explosion-proofmotor. If hydraulic or pneumatic:operating medium, pressure.

6. Accessories and controls: limitswitches, instrumentation,valving, tanks, pumps, etc.

Specify the following when ordering a Cameron Ball Valve:

Specify the following when ordering another manufacturers power operator to fit a Cameron Ball Valve:

80 06 0 1 -2 -1

Ball Valve Figure Numbers

Additional trims available upon request

8/12/2019 TC1191

3/31

1

Page

Welded Body Valve Features and Benefits ..........................................................................................2-5

Standards, Materials, Torque Information and Trims..............................................................................6

Dimensional Codes ....................................................................................................................................7

150 lb Class: Full and Reduced Opening ............................................................................................8-9300 lb Class: Full and Reduced Opening ........................................................................................10-11

400 lb Class: Full and Reduced Opening ........................................................................................12-13



1500 lb Class: Full and Reduced Opening ......................................................................................18-19

2500 lb Class: Full and Reduced Opening ..........................................................................................20

API Flanged End: Full and Reduced Opening ................................................................................21-22

Centerline to Mounting Flange Dimensions ......................................................................................23

Square Nut and Adapter Flange Mounting Dimensions....................................................................24

Keyed Shaft and Adapter Flange Mounting Dimensions ..................................................................25Manual Gear Dimensions ....................................................................................................................26

Welded and Seamless Pipe Dimensions ..............................................................................................27

Cameron Ball Valve In-Line Launcher ....................................................................................................28

Cameron ball valves are part of a

wide range of products offered by

the Cooper Cameron Valve Division

of Cooper Cameron Corporation.

CAMERON BALL VALVES TABLE OF CONTENTS

8/12/2019 TC1191

4/31

8/12/2019 TC1191

5/31

Valve Open

Body Vent

SD-7018SD-7018

Valve Closed

Body VentDouble Block and BleedWhether in the open or closed position,

pressure on each side of the ball is

blocked from the body cavity by the

seat ring. The body cavity can be blown

down or drained through the body port.

Stem Seals

Cameron ball valves incorporate delta

and lip seals made of PTFE in the upperstem area. PTFE is a low friction, non-

deteriorating material that is not subject

to rapid decompression explosion. Valve

stem sizes 2 and larger have a provi-

sion for the injection of sealant to

establish a secondary seal.

4

Distinctive Body Design

The Cameron all-welded ball valve body is compact and streamlined for maximum

strength and minimum weight. Forged steel is used to assure uniform fine grain

structure and toughness.

The spherical body provides maximum resistance to pressure and pipeline stresses.

This compact spherical design also eliminates body flanges to reduce overall size andleak paths. This lightweight design allows for significant savings in overall structural

reinforcement costs, particularly in offshore platforms. The stand alone design

means that no extra foundations or supports are needed. In addition, the spherical

shape creates easier installation, coating and wrapping procedures than standard

bolted concepts.

Trunnion Mounting

Regardless of size or pressure rating, every Cameron ball valve is trunnion-mounted.

High strength forged stems are located in PTFE-impregnated stainless steel bearings

for smooth, accurate operations. Trunnion mounted stems absorb the thrust from line

pressure, preventing excess friction between the ball and seats, so even at full rated

working pressure, operating torque stays low.

CAMERON BALL VALVES FEATURES AND BENEFITS

Fire Tested to RecognizedStandards

Cameron ball valves have been fire-testedand can be supplied to API 6FA and API

607. Fire test programs are usually ongo-

ing. If industry standards change or cus-

tomer requirements are different from

above, call your Cooper Cameron Valves

representative.

Typical boltedvalve design

Cameronsphericalball valve

Typical gatevalve design

SD-24086

SD-0163

SD-7017

8/12/2019 TC1191

6/31

5

Secondary Seat Seal

The secondary seat seal sealant injection system provides a fast, simple way of

restoring tight shut-off if any foreign object should damage the sealing surfaces.

The injection system can also be used for routine flushing of the seat ring area in

services where this may be required.

Automatic Adjusting Seats

At low pressures, seat-to-ball contact is maintained by Bellville springs. At higher

pressures, seat contact is reinforced by line pressure. Tight long term shut-off is

obtained by Nylon seat inserts which are firmly locked into the seat ring. If required,

substitute materials can be used in the insert of the ring. Pressure energized lip seals

made from PTFE are used between the seat ring and the inside of the body.

Non-Lubricated Design

Self lubricated, low friction PTFE is

used for stem bearings, stem seals, and

body seats. Nylon or other low friction

materials are used for seat inserts.

Self-lubricating seals and stem bearings

give predictable operating torque for

the life of the valve.

Rotating Seats

Cameron ball valve sizes 14 and larger

incorporate the exclusive rotating seat

feature. Both seats rotate 15 degrees

each time the valve is closed, exposing a

fresh sealing surface to the critical area

where flow is pinched off.

Automatic Internal Relief of Body Pressure

Relief of excess body cavity pressure is automatic, avoiding dangerous pressure build-

up. Any pressure exceeding downstream line pressure by approximately 200 psi

pushes the downstream seat away from the ball, allowing the pressure to escape

into the pipeline.

CAMERON BALL VALVES FEATURES AND BENEFITS

SD-24026

Trapped LinePressure

EscapingPressure

LinePressure

SD-24087

SD-7808

SD-7807

8/12/2019 TC1191

7/31

CAMERON BALL VALVES STANDARDS,MATERIALS, TORQUE INFORMATION AND TRIMS

Trim Numbers

Trim Pressure Rating Temperature Rating Corrosion ResistantRegular

(NACE MR01-75)

Standard Class 150-2500 -20 to +250F (-29 to +121C) 1 212API 2000-5000 -20 to +250F (-29 to +121C) 2 213

Low Temperature Class 150-2500 -50 to +250F (-29 to +121C) 8 216API 2000-5000 -50 to +250 F (-29 to +121 C) 217

High Temperature Class 150-600 -20 to +375F (-29 to +190C) 4 222

Tefzel Class 150-1500 -20 to +300F (-29 to +149C) 140 214(Acidizing) API 2000-5000 -20 to +300F (-29 to +149C) 108 215

Tefzel Class 150-1500 -50 to +300F (-46 to +149C) 223 Low Temperature API 2000-5000 -50 to +300 F (-46 to +149 C)

Duplex (Internal) Class 150-1500 -20 to +250 F (-29 to +121 C) 276

Stainless SteelFull Duplex Class 150-1500 -50 to +250F (-29 to +121C) 504Stainless Steel

6

Standards

Cameron ball valves conform to one or more of the following

specifications for pressure, temperature ratings and dimen-

sions:

ANSI

API-6DAPI-6A

DIN

AFNOR

British Standards

ISO 9000

Materials

Materials used in ball valve construction are broadly equivalent

at all Cooper Cameron Valve manufacturing plants. However,

the availability of local supplies, the need to conform to nation-

al standards and to offer various trims may necessitate some

variations. In corrosive applications, valve trims can be offered

using various types of alloys and stainless steels. For more

information on material specifications and properties, please

contact your local Cooper Cameron Valves representative.

Torque Information

Please contact your Cooper Cameron Valves representative to

obtain a copy of the engineering bulletin which provides

detailed torque information for sizing of power actuators.

Trims

Cameron ball valves are available in a variety of trims. The

table at the left shows standard trims. The table below showsthe more common trims. Other trims are available upon

request. For more information on trims, contact your Cooper

Cameron Valves representative.

Pressure Range Class 150-2500

Temperature Range 20 to +250F

29 to +121C

Body ASTM A350 Gr. LF-2(M)

End Connection ASTM A350 Gr. LF-2(M)

Ball ASTM A694 Gr. F50 Cr. Pl.

Seat Ring AISI 1040

Seat Load Spring AISI 1040

Stem Seals PTFE

Lip Seals PTFE

Seat Ring Insert Nylon

Trim Materials for Standard Valves

Optional Trim Materials

8/12/2019 TC1191

8/31

CAMERON BALL VALVES DIMENSIONAL DATA

7

Dimensional Codes for Flanged and Welded Ends (Full and Reduced Openings)

Dimensional Codes for Cameron Manual Gear Operators

Code Identification:

A End-to-end (length dimension)

B Bore diameter

C Center line-to-bottom

D1 Flanged outside diameterD2 Flanged inside dimension

E Sphere dimension

Code Identification:

H Center of bore to top of square nut for lever operated

valves, center of bore to handwheel for gear operated

valves

L Center of bore to end of lever

G Handwheel diameter

The tables on the following pages list the major dimensions

for standard size Cameron ball valves. Please consult your

Cooper Cameron Valves representative for any special sizes

not listed.

Valves are grouped individually by pressure class. For conve-

nience, separate tables are provided for valves with fullopenings (same ball bore and end in side diameter.) and

reduced openings (bore one type size smaller than end inside

diameter).

The tables also list the final dimensions and approximate

weights for each valve with the operator that is normally

furnished.

The data is for your general information only. Design changes

do become necessary from time to time and these could result

in variations from the existing data. We therefore recommendthat you check with your local Cooper Cameron Valves sales

office for any details which are critical to your operations.

E

B

A

C

D1

D2

H

L

G

H

SD-24027

SD-24028 SD-24029

8/12/2019 TC1191

9/31

8


Length (A) of a weld x flanged end valve is one half the sum of lengths (A) of a weld and of a flange end of thread rating.

* Short pattern. # Length exceeds specified dimension of the API 6D.

Dimensions of 26 through 42 flanges are per MSS-SP-44.

Full Opening 150 lb. Class

285 psi WOG (20.0 kg/cm2)450 psi TEST (31.6 kg/cm2)

G

H

H

L

E

B

A

C

D1

D2

50.8 52.3 25.4 177.8 190.5 152.4 52.3 #279.4 100.1 127.0 609 161.0 18 15

76.2 79.5 25.4 203.2 215.9 190.5 79.5 #317.5 130.0 171.5 609 189.0 29 26

101.6 103.1 38.1 228.6 241.3 228.6 103.1 355.6 150.9 215.9 914 214.1 40 36

152.4 152.4 38.1 393.7 406.4 279.4 152.4 457.2 200.9 285.8 914 264.9 119 108

203.2 203.2 50.8 457.2 469.9 342.9 203.2 #546.1 254.0 393.7 457 320.3 171 153

254.0 254.0 50.8 533.4 546.1 406.4 254.0 #596.9 307.8 469.9 457 370.8 285 255

304.8 304.8 76.2 609.6 622.3 482.6 304.8 #673.1 368.3 567.9 457 511.5 445 395

355.6 336.6 76.2 685.8 698.5 533.4 336.6 *723.9 371.9 609.6 609 537.4 551 488

406.4 387.4 76.2 762.0 774.7 596.9 387.4 *774.7 406.7 668.5 609 572.0 685 603

457.2 438.2 101.6 863.6 876.3 635.0 438.2 850.9 489.0 741.7 609 665.2 864 764

508.0 489.0 101.6 914.4 927.1 698.5 489.0 901.7 528.6 819.7 457 704.9 1120 911

558.8 539.8 101.6 1016.0 1028.7 749.3 539.8 *977.9 565.9 914.4 457 780.8 1694 1509

609.6 590.6 101.6 1066.8 1079.5 812.8 590.6 *1066.8 601.7 984.5 457 778.0 1898 1638

660.4 635.0 127.0 1143.0 870.0 635.0 *1130.3 672.8 1060.5 609 872.2 2298 1989

711.2 685.8 127.0 1244.6 927.1 685.8 *1193.8 708.2 1139.4 609 907.3 2840 2480

762.0 736.6 127.0 1295.4 984.3 736.6 *1244.6 749.6 1216.7 609 949.2 3369 2997

863.6 831.9 127.0 1473.2 1111.3 831.9 *1384.3 816.9 1371.6 762 1016.3 4592 4146

914.4 876.3 127.0 1524.0 1168.4 876.3 *1435.1 857.5 1443.5 914 1056.6 5449 4991

1016.0 977.9 190.5 1752.6 1289.1 977.9 *1651.0 1019.6 1651.0 762 1276.4

1066.8 1047.8 190.5 1828.8 1346.2 1047.8 *1689.1 1061.2 1742.4 1067 1318.0

1219.2 1181.1 190.5 2032.0 1511.3 1181.1 *2133 1166 1956

2 2.06 1 7 7.5 6 2.06 #11 3.94 5 24 6.34 39 32

3 3.13 1 8 8.5 7.5 3.13 #12.5 5.12 6.75 24 7.44 64 58

4 4.06 1.5 9 9.5 9 4.06 14 5.94 8.5 36 8.43 88 79

6 6 1.5 15.5 16 11 6 18 11.73 11.25 36 10.43 263 237

8 8 2 18 18.5 13.5 8 #21.5 10 15.5 18 12.61 380 341

10 10 2 21 21.5 16 10 #23.5 12.12 18.5 18 14.6 633 567

12 12 3 24 24.5 19 12 #26.5 14.5 22.36 18 20.14 980 870

14 13.25 3 27 27.5 21 13.25 *28.5 14.64 24 24 21.16 1215 1075

16 15.25 3 30 30.5 23.5 15.25 *30.5 16.01 26.32 24 22.52 1510 1330

18 17.25 4 34 34.5 25 17.25 *33.5 19.25 29.2 24 26.19 1904 1684

20 19.25 4 36 36.5 27.5 19.25 *35.5 20.81 32.27 18 27.25 2468 2008

22 21.25 4 40 40.5 29.5 21.25 *38.5 22.28 36 18 30.74 3734 3327

24 23.25 4 42 42.5 32 23.25 * 42 23.69 38.76 18 30.63 4184 3610

26 25 5 45 34.25 25 *44.5 26.49 41.75 24 34.34 5066 4385

28 27 5 45 36.5 27 * 47 27.88 44.86 24 35.72 6261 5468

30 29 5 51 38.75 29 * 49 29.51 47.9 24 37.37 7427 6607

34 32.75 5 58 43.75 32.75 *54.5 32.16 53.64 30 40.01 10123 9140

36 34.5 5 60 46 34.5 *56.5 33.76 56.83 36 41.6 12012 11003

40 38.5 7.5 69 50.75 38.5 * 65 40.14 65 30 50.25

42 41.25 7.5 72 53 41.25 *66.5 41.78 68.6 42 51.89

48 46.5 7.5 80 59.5 46.5 * 84 45.9 77

Flanged End SizeData for Valve with Operator

Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

Stem

Sizemm

Raised

FaceLengthA mm

Ring

JointLengthA mm

Diam.D1 mm

Diam.D2mm

LengthAmm

C.L.To

BottomCmm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearGmm H

mm

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

10/31

9


76.2 52.3 25.4 203.2 215.9 190.5 79.5 #279.4 100.1 127.0 609 161.0 18 16101.6 79.5 25.4 228.6 241.3 228.6 103.1 #317.5 130.0 171.5 609 189.0 32 29

152.4 103.1 38.1 393.7 406.4 279.4 152.4 #355.6 150.9 215.9 914 214.1 52 47

203. 152.4 38.1 457.2 469.9 342.9 203.2 457.2 298 285.8 914 264.9 131 118

254.0 203.2 50.8 533.4 546.1 406.4 254.0 #546.1 254.0 393.7 457 320.3 191 171

304.8 254.0 50.8 609.6 622.3 482.6 304.8 #596.9 307.8 469.9 457 370.8 351 315

355.6 304.8 76.2 685.8 698.5 533.4 336.6 #673.1 368.3 567.9 457 511.5 524 461

406.4 336.6 76.2 762.0 774.7 596.9 387.4 *723.9 371.9 609.6 609 537.4 624 542

457.2 387.4 76.2 863.6 876.3 635.0 438.2 *774.4 406.7 668.5 609 572.0 803 703

508.0 438.2 101.6 914.4 927.1 698.5 489.0 *850.9 489.0 741.4 609 665.2 950 818

558.8 489.0 101.6 1016.0 1028.7 749.3 539.8 *901.7 528.6 819.7 457 704.9 1247 1004

609.6 539.8 101.6 1066.8 1079.5 812.8 590.6 *977.7 565.9 914.4 457 780.8 1795 1564

660.4 590.6 101.6 1143.0 870.0 635.0 *1066.8 601.7 984.5 457 778.0 2102 1789

711.2 635.0 127.0 1244.6 927.1 685.8 *1130.3 672.8 1060.5 609 872.2 2582 2185

762.0 685.8 127.0 1295.4 984.3 736.6 *1193.8 708.2 1139.4 609 907.3 3119 2689

812.8 736.6 127.0 1371.6 1047.8 831.9 *1244.6 749.6 1216.7 609 949.2 3753 3348

914.4 831.9 127.0 1524. 1168.4 876.3 *1384.3 816.9 1362.5 762 1016.3 4880 4475

1066.8 876.3 127.0 1828.8 1346.2 1047.8 *1435.1 857.5 1443.5 914 1056.6

3 2.06 1 8 8.5 7.5 3.13 #11 3.94 5 24 6.34 40 36

4 3.13 1 9 9.5 9 4.06 #12.5 5.12 6.75 24 7.44 70 63

6 4.06 1.5 10.5 11 11 6 #14 5.94 8.5 36 8.43 115 103

8 6 1.5 18 18.5 13.5 8 18 11.73 11.25 36 10.43 290 261

10 8 2 21 21.5 16 10 #21.5 10 15.5 18 12.61 424 381

12 10 2 24 24.5 19 12 #23.5 12.12 18.5 18 14.6 780 700

14 12 3 27 27.5 21 13.25 #26.5 14.5 22.36 18 20.14 1115 1015

16 13.25 3 30 30.5 23.5 15.25 *28.5 14.64 24 24 21.16 1375 1195

18 15.25 3 34 34.5 25 17.25 *30.5 16.01 26.32 24 22.52 1770 1550

20 17.25 4 36 36.5 27.5 19.25 *33.5 19.25 29.2 24 26.19 2094 1804

22 19.25 4 40 40.5 29.5 21.25 *35.5 20.81 32.27 18 27.75 2758 2214

24 21.25 4 42 42.5 32 23.25 *38.5 22.28 36 18 30.74 3957 3451

26 23.25 4 45 34.25 25 *42 23.69 38.76 18 30.63 4634 3943

28 25 5 49 36.5 27 *44.5 26.49 41.75 24 34.34 5692 4818

30 27 5 51 38.75 29 *47 27.88 44.86 24 35.72 6875 5928

32 29 5 54 41.25 32.75 *49 29.51 47.9 24 37.37 8273 7381

36 32.75 5 60 46 34.5 *54.5 32.16 53.64 30 40.01 10759 9865

42 34.5 5 72 53 41.25 *56.5 33.76 56.83 36 41.6

Note: Venturi opening or other reduced bore valves are available upon request.


* Short pattern. # Length exceeds specified dImension of the API 6D.


Reduced Opening 150 lb. Class



Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBore

B mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

11/31

10


2 2.06 1 8.5 9.125 6.5 2.06 #11 3.94 5 24 6.34 41 34

3 3.13 1 11.125 11.75 8.25 3.13 #12.5 5.12 6.75 24 7.44 80 72

4 4.06 1.5 12 12.625 10 4.06 #14 5.94 8.5 36 8.43 120 108

6 6 1.5 15.875 16.5 12.5 6 18 11.73 11.25 36 10.43 275 247

8 8 2 19.75 20.375 15 8 #21.5 10 15.5 18 12.61 455 406

10 10 2 22.375 23 17.5 10 #23.5 12.12 18.5 24 14.6 726 648

12 12 3 25.5 26.125 20.5 12 #26.5 14.5 22.36 18 20.14 1100 990

14 13.25 3 30 30.625 23 13.25 *28.5 14.64 24 24 21,16 1460 1314

16 15.25 3 33 33.625 25.5 15.25 *30.5 16.01 26.32 24 22.52 1812 1631

18 17.25 4 36 36.625 28 17.25 *33.5 19.25 29.2 24 26.19 2299 2067

20 19.25 4 39 39.75 30.5 19.25 *35.5 20.81 32.27 18 27.75 2808 2508

22 21.25 4 43 43.875 33 21.25 *38.5 22.28 36 24 30.74 4257 3327

24 23.25 4 45 45.875 36 23.25 *42 23.69 38.76 24 30.63 4770 3610

26 25 5 49 50 38.25 25 *44.5 26.49 41.75 24 34.34 5775 4335

28 27 5 53 54 40.75 27 *47 27.88 44.86 24 35.72 7138 5518

30 29 5 55 56 43 29 *49 29.51 47.9 30 37.37 8467 6607

34 32.75 5 64 65.125 47.5 32.75 *54.5 32.16 53.64 36 40.01 11540 9140

36 34.5 7.5 68 69.125 50 34.5 *56.5 36.8 56.83 24 46.92 13693 11093

40 38.5 7.5 74 48.75 38.5 *65 40.14 65 36 50.25

42 41.25 7.5 76 50.75 41.25 *66.5 41.78 68.6 42 51.89

48 46.5 7.5 86 57.75 46.5 *84 45.9 77

50.8 52.3 25.4 215.9 231.8 165.1 52.3 #279.4 100.1 127.0 609 161.0 19 15

76.2 79.5 25.4 282.6 298.5 209.6 79.5 #317.5 130.0 171.5 609 189.0 36 33

101.6 103.1 38.1 304.8 320.7 254.90 103.1 #355.6 150.9 215.9 914 214.1 54 49

152.4 152.4 38.1 403.2 419.1 317.5 152.4 457.2 298 285.8 914 264.9 125 112

203.2 203.2 50.8 501.7 517.5 381.0 203.2 #546.1 254.0 393.7 457 320.3 205 183

254.0 254.0 50.8 568.3 584.2 444.5 254.0 #596.9 307.8 469.9 609 370.8 327 292

304.8 304.8 76.2 647.7 663.6 520.7 304.8 #673.1 368.3 567.9 457 511.5 499 449

355.6 336.6 76.2 762.0 777.9 584.2 336.6 *723.9 371.9 609.6 609 537.4 662 596

406.4 387.4 76.2 838.2 854.1 647.7 387.4 *774.7 406.7 668.5 609 572.0 822 740

457.2 438.2 101.6 914.4 930.3 711.2 438.2 *850.9 489.0 741.7 609 665.2 1043 938

508.0 489.0 101.6 990.6 1009.7 774.7 489.0 *901.7 528.6 819.7 457 704.9 1274 1138

558.8 539.8 101.6 1092.2 1114.4 838.2 539.8 *977.9 565.9 914.4 609 780.8 1931 1509

609.6 590.6 101.6 1143.0 1165.2 914.4 590.6 *1066.8 601.7 984.5 609 778.0 2164 1637

660.4 635.0 127.0 1244.6 1270.0 971.6 635.0 *1130.3 672.8 1060.5 609 872.2 2620 1966

711.2 685.8 127.0 1346.2 1371.6 1035.1 685.8 *1193.8 708.2 1139.4 609 907.3 3238 2503

762.0 736.6 127.0 1397.0 1422.4 1092.2 736.6 *1244.6 749.6 1216.7 762 949.2 3840 2997

863.6 831.9 127.0 1625.6 1654.2 1206.5 831.9 *1384.3 816.9 1362.5 914 1016.3 5234 4146

914.4 876.3 190.5 1727.2 1755.8 1270.0 876.3 *1435.1 934.7 1443.5 609 1191.8 6211 5032

1016.0 977.9 190.5 1879.6 1238.3 977.9 *1651.0 1019.6 1651.0 914 1276.4

1066.8 1047.8 190.5 1930.4 1289.1 1047.8 *1689.1 1061.2 1742.4 1067 1318.0

1219.2 1181.1 190.5 2184.4 1466.9 1181.1 *1930.4 1143.0 1955.8







Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

Nom

Diam.mm

Ball

BoreB mm

StemSizemm

Raised

FaceLengthA mm

Ring

JointLengthA mm

Diam.

D1 mm

Diam.

D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

12/31

11


3 2.06 1 11.125 11.75 8.25 3.13 *11 3.94 5 24 6.34 65 59

4 3.13 1 12 12.625 10 4.06 #12.5 5.12 6.75 24 7.44 95 85

6 4.06 1.5 15.875 16.5 12.5 6 *14 5.94 8.5 36 8.43 175 157

8 6 1.5 19.75 20.375 15 8 *18 11.73 11.25 36 10.43 335 301

10 8 2 18 18.625 17.5 10 *21.5 10 15.5 18 12.61 522 467

12 10 2 19.75 20.375 20.5 12 *23.5 12.12 18.5 24 14.6 848 758

14 12 3 30 30.625 23 13.25 *26.5 14.5 22.36 18 20.14 1285 1165

16 13.25 3 33 33.625 25.5 15.25 *28.5 14.64 24 24 21.16 1642 1486

18 15.25 3 36 36.625 28 17.25 *30.5 16.01 26.32 24 22.52 2114 1903

20 17.25 4 39 39.75 30.5 19.25 *33.5 19.25 29.2 24 26.19 2511 2258

22 19.25 4 43 43.875 33 21.25 *35.5 20.81 32.27 18 27.75 3144 2714

24 21.25 4 45 45.875 36 23.25 *38.5 22.28 36 24 30.74 4611 3451

26 23.25 4 49 50 38.25 25 *42 23.69 38.76 24 30.63 5283 3943

28 25 5 53 54 40.75 27 *44.5 26.49 41.75 24 34.34 6488 4868

30 27 5 55 56 43 29 *47 27.88 44.86 24 35.72 7838 5978

32 29 5 60 61.125 45.25 32.75 *49 29.51 47.9 30 37.37 9431 7381

36 32.75 5 68 69.125 50 34.5 *54.5 32.16 53.64 36 40.01 12265 9865

42 34.5 7.5 76 50.75 41.25 *56.5 36.8 56.83 24 46.92

76.2 52.3 25.4 282.6 298.5 209.6 79.5 *279.4 100.1 127.0 609 161.0 29 27101.6 79.5 25.4 304.8 320.7 254.0 103.1 #317.5 130.0 171.5 609 189.0 43 39

152.4 103.1 38.1 403.2 419.1 317.5 152.4 *355.6 150.9 215.9 914 214.1 79 71

203.2 152.4 38.1 501.7 517.5 381.0 203.2 *457.2 298 285.8 914 264.9 152 136

254.0 203.2 50.8 568.3 584.2 444.5 254.0 *546,1 254.0 393.7 457 320.3 235 210

304.8 254.0 50.8 647.7 663.6 520.7 304.9 *596.9 307.8 469.9 609 370.8 382 341

355.6 304.8 76.2 762.0 777.9 584.2 336.6 *673.1 368.3 567.9 457 511.5 587 528

406.4 336.6 76.2 838.2 854.1 647.7 387.4 *723.9 371.9 609.6 609 537.4 745 678

457.2 387.4 76.2 914.4 930.3 711.2 438.2 *774.7 406.7 668.5 609 572.0 959 862

508.0 438.2 101.6 990.6 1009.7 774.7 489.0 *850.9 489.0 741.7 609 665.2 1138 1024

558.8 489.0 101.6 1092.2 1114.4 838.2 539.8 *901.7 528.6 819.7 457 704.9 1426 1231

609.6 539.8 101.6 1143.0 1165.2 914.4 590.6 *977.9 565.9 914.4 609 780.8 2091 1565

660.4 590.6 101.6 1244.6 1270.0 971.6 635.0 *1066.8 601.7 984.5 609 778.0 2396 1789

711.2 635.0 127.0 1346.2 1371.6 1035.1 685.8 *1130.3 672.8 1060.5 609 872.2 2943 2208

762.0 685.8 127.0 1397.0 1422.4 1092.2 736.6 *1193.8 708.2 1139.4 609 907.3 3555 2612

812.8 736.6 127.0 1524.0 1552.6 1149.4 831.9 *1244.6 749.6 1216.7 762 949.2 4278 3348

914.4 831.9 127.0 1727.2 1755.8 1270.0 867.3 *1384.3 816.9 1362.5 914 1016.3 5563 4475

1066.8 876.3 190.5 1930.4 1289.1 1047.8 *1435.1 934.7 1443.5 609 1191.8



* Short pattern. # Length exceeds specified dImension of the API 6D.




Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm


G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

13/31

2 2.06

3 3.13

4 4.06 1.5 16 16.125 10 4.06 *14 5.94 8.5 36 8.43 140 126

6 6 1.5 19.5 19.625 12.5 6 *18 11.73 11.25 36 10.43 305 274

8 8 2 23.5 23.625 15 8 *21.5 10 15.5 18 12.61 530 473

10 10 2 26.5 26.625 17.5 10 *23.5 12.12 18.5 24 14.6 910 819

12 12 3 30 30.125 20.5 12 *26.5 14.5 22.36 18 20.14 1390 1240

14 13.25 3 32.5 32.625 23 13.25 *28.5 14.64 24 18 21.16 1774 1576

16 15.25 4 35.5 35.625 25.5 15.25 *30.5 17.84 26.32 18 24.78 2282 2040

18 17.25 4 38.5 35.625 28 17.23 *33.5 19.24 29.2 24 26.19 2918 2626

20 19.25 5 41.5 41.75 30.5 19.25 *35.5 22.11 32.27 24 30 3370 3028

22 21.25 5 45 45.375 33 21.25 38.5 23.63 36 24 31.53 5108 4332

24 23.25 5 48.5 48.875 36 23.25 *42 25.05 38.76 24 32.95 5963 5278

26 25 5 51.5 52 38.25 25 *44.5 26.49 41.75 24 34.34 7219 5872

28 27 5 55 55.5 40.75 27 *47 27.88 44.86 30 35.72 8923 7464

30 29 5 60 60.5 43 29 *49 29.51 47.9 36 37.37 10584 8657

34 32.75 7.5 70 70.625 47.5 32.75 *54.5 35.19 53.64 30 45.31 14425 12712

36 34.5 7.5 74 74.625 50 34.5 *56.5 36.8 56.83 30 46.92 18116 16700

40 38.5 7.5 78 50 38.5 *65 40.14 65 42 50.25 25100 23800

42 41.25 7.5 81 52 41.25 *66.5 41.78 68.6 42 51.89 27900 26200

48 46.5 9 91 59.5 46.5 *84 47.98 77

Use 600 lb. Class Valves


12


50.8 52.3

76.2 79.5

101.6 103.1 38.1 406.4 409.6 254.0 103.1 *355.6 150.9 215.9 914 214.1 64 57

152.4 152.4 38.1 495.3 498.5 317.5 152.4 *457.2 298 285.8 914 264.9 138 124

203.2 203.2 50.8 596.9 600.1 381.0 203.2 *546.1 254.0 393.7 457 320.3 240 215

254.0 254.0 50.8 673.1 676.3 444.5 254.0 *596.9 307.8 469.9 609 370.8 413 371

304.8 304.8 76.2 762.0 765.2 520.7 304.8 *673.1 368.3 567.9 457 511.5 631 562

355.6 336.6 76.2 825.5 828.7 584.2 336.6 *723.9 371.9 609.6 457 537.4 804 714

406.4 387.4 101.6 901.7 904.9 647.7 387.4 *774.7 453.1 668.5 457 629.4 1035 925

457.2 438.2 101.6 977.9 981.1 711.2 438.2 *850.9 489.0 741.7 609 665.2 1324 1191

508.0 489.0 127.0 1054.1 1060.5 774.7 489.0 *901.7 561.6 819.7 609 762.0 1529 1374

558.8 539.8 127.0 1143.0 1152.5 838.2 539.8 *977.9 600.2 914.4 609 800.9 2317 1955609.6 590.6 127.0 1231.9 1241.4 914.4 590.6 *1066.8 636.3 984.5 609 836.9 2605 2394

660.4 635.0 127.0 1308.1 1320.8 971.6 635.0 *1130.3 672.8 1060.5 609 872.2 3275 2664

711.2 685.8 127.0 1397.0 1409.7 1035.1 685.8 *1193.8 708.2 1139.4 762 907.3 4047 3386

762.0 736.6 127.0 1524.0 1536.7 1092.2 736.6 *1244.6 749.6 1216.7 914 949.2 4801 3927

863.6 831.9 190.5 1778.0 1793.9 1206.5 831.9 *1384.3 893.8 1362.5 762 1150.9 6543 5766

914.4 876.3 190.5 1879.6 1895.5 1270.0 876.3 *1435.1 934.7 1443.5 762 1191.8 8218 7575

1016.0 977.9 190.5 1981.2 1270.0 977.9 *1651.0 1019.6 1651.0 1067 1276.4 11385 10796

1066.9 1047.8 190.5 2057. 1320.8 1047.8 *1689.1 1061.2 1742.4 1067 1318.0 12655 11884

1219.2 1181.1 228.6 2311.4 1511.3 1181.3 *2133 1219 1956









Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

Stem

Sizemm

Raised

FaceLengthA mm

Ring

JointLengthA mm

Diam.D1 mm

Diam.D2mm

LengthAmm

C.L.To

BottomCmm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearGmm H

mm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

14/31

13


3 2.06

4 3.13 1 16 16.125 10 4.06 *12.5 5.12 6.75 24 7.44 110 99

6 4.06 1.5 19.5 19.625 12.5 6 *14 5.94 8.5 36 8.43 195 175

8 6 1.5 23.5 23.625 15 8 *18 11.73 11.25 18 10.43 430 387

10 8 2 26.5 26.625 17.5 10 *21.5 10 15.5 18 12.61 635 567

12 10 2 30 30.125 20.5 12 *23.5 12.12 18.5 24 14.6 1110 999

14 12 3 32.5 32.625 23 13.25 *26.5 14.5 22.36 18 20.14 1620 1458

16 13.25 3 35.5 35.625 25.25 15.25 *28.5 14.64 24 18 21.16 2034 1828

18 15.25 4 38.5 38.625 28 17.25 *30.5 17.84 26.32 18 24.78 2592 2351

20 17.25 4 41.5 41.75 30.5 19.25 *33.5 19.25 29.2 24 26.19 3348 3013

22 19.25 5 45 45.375 33 21.25 *35.5 22.11 32.27 24 30 3772 3322

24 21.25 5 48.5 48.875 36 23.25 *38.5 23.63 36 24 31.53 5413 4457

26 23.25 5 51.5 52 38.25 25 *42 25.05 38.76 24 32.95 6604 5413

28 25 5 55 55.5 40.75 27 *44.5 26.49 41.75 24 34.34 8110 6561

30 27 5 60 60.5 43 29 *47 27.88 44.86 30 35.72 9798 8184

32 29 5 65 65.625 45.25 32.75 *49 29.51 47.9 36 37.37 11789 9694

36 32.75 7.5 74 74.625 50 34.5 *54.5 35.19 53.64 30 45.31 15331 13517

42 34.5 7.5 81 52 41.25 *56.5 36.8 56.83 30 46.92

76.2 52.3101.6 79.5 25.4 406.7 409.6 254.0 103.1 *317.5 130.0 171.5 609 189.0 50 45

152.4 103.1 38.1 495.3 498.5 317.5 152.4 *355.6 150.9 215.9 914 214.4 88 79

203.2 152.4 38.1 596.9 600.1 381.0 203.2 *457.2 298 285.8 457 264.9 195 176

254.0 203.2 50.8 673.1 676.3 444.5 254.0 *546.1 254.0 393.7 457 320.3 288 257

304.8 254.0 50.8 762.0 765.2 520.7 304.8 *596.9 307.8 469.9 609 370.8 503 453

355.6 304.8 76.2 825.5 828.7 584.2 336.6 *673.1 368.3 567.9 457 511.5 735 661

406.4 336.6 76.2 901.7 904.9 647.7 387.4 *723.9 371.9 609.6 457 537.4 923 829

457.2 387.4 101.6 977.9 981.1 711.2 438.2 *774.7 453.1 668.5 457 629.4 1175 1066

508.0 438.2 101.6 1054.1 1060.5 774.7 489.0 *850.9 489.0 741.7 609 665.2 1519 1367

558.8 489.0 127.0 1143.0 1152.5 838.2 539.8 *901.7 561.6 819.7 609 762.0 1711 1507

609.6 539.8 127.0 1231.9 1241.4 914.4 590.6 *977.9 600.2 914.4 609 800.9 2455 2022

660.4 590.6 127.0 1308.1 1320.8 971.6 635.0 *1066.8 636.3 984.5 609 836.9 2942 2455

711.2 635.0 127.0 1397.0 1409.7 1035.1 685.8 *1130.3 672.8 1060.5 609 872.2 3679 2976

762.0 685.8 127.0 1524.0 1536.7 1092.2 736.6 *1193.8 708.2 1139.4 762 907.3 4444 3712

812.8 736.6 127.0 1651.0 1666.9 1149.4 831.9 *1244.6 749.6 1216.7 914 949.2 5348 4397

914.4 831.9 190.5 1879.6 1895.5 1270.0 876.3 *1384.3 893.8 1362.5 762 1150.9 6954 6131

1066.8 876.3 190.5 2057.4 1320.8 1047.8 *1435.1 934.7 1443.5 762 1191.8





* Short pattern.





Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm


G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

15/31

14


2 2.06 1 11.5 11.625 6.5 2.06 *11 3.94 5 24 6.34 44 40

3 3.13 1 14 14.125 8.25 3.13 *12.5 5.12 6.75 24 7.44 85 78

4 4.06 1.5 17 17.125 10.75 4.06 *14 5.94 8.5 36 8.43 165 148

6 6 1.5 22 22.125 14 6 *18 11.73 11.25 36 10.43 445 397

8 8 2 26 26.125 16.5 8 *21.5 10 15.5 24 12.61 670 603

10 10 2 31 31.125 20 10 *23.5 12.12 18.5 30 14.6 1050 945

12 12 3 33 33.125 22 12 *26.5 14.5 22.36 18 20.14 1510 1359

14 13.25 3 35 35.125 23.75 13.25 *28.5 14.64 24 24 21.16 2030 1825

16 15.25 4 39 39.125 27 15.25 *30.5 17.84 26.32 18 24.78 2483 2232

18 17.25 4 43 43.125 29.25 17.25 *33.5 19.25 29.2 24 26.19 2985 2685

20 19.25 5 47 47.25 32 19.25 *35.5 22.11 32.27 24 30 4208 3628

22 21.25 5 51 51.375 34.25 21.25 *38.5 23.63 36 24 31.53 5772 4332

24 23.25 5 55 55.375 37 23.25 *42 25.05 38.76 30 32.95 6938 5278

26 25 5 57 57.5 40 25 *44.5 26.49 41.75 36 34.34 8013 5963

28 27 7.5 61 61.5 42.25 27 *47 30.87 44.86 30 40.99 9905 7555

30 29 7.5 65 65.5 44.5 29 *49 32.53 47.9 30 42.65 11748 8748

34 32.75 7.5 76 76.625 49 32.75 *54.5 35.19 53.64 42 45.31 16012 12712

36 34.5 7.5 82 82.625 51.75 34.5 *56.5 36.8 56.83 42 46.92 19998 16700

40 38.5 9 80 52 38.5 *65 42.02 65 42 55.425 26900 23800

42 41.25 9 83 55.25 41.25 66.5 43.66 69 42 57.06 29920 26200

48 46.5 11 94 62.75 46.5 *84 51.18 77.33 --

50.8 52.3 25.4 292.1 295.3 165.1 52.3 *279.4 100.1 127.0 609 161.0 20 18

76.2 79.5 25.4 355.6 358.8 209.6 79.5 *317.5 130.0 171.5 609 189.0 39 35

101.6 103.1 38.1 431.8 435.0 273.1 103.1 *355.6 150.9 215.9 914 214.1 75 67

152.4 152.4 38.1 558.8 562.0 355.6 152.4 *457.2 298 285.8 914 264.9 202 180

203.2 203.2 50.8 660.4 663.6 419.1 203.2 *546.1 254.0 393.7 609 320.3 304 274

254.0 254.0 50.8 787.4 790.6 508.0 254.0 *596.9 307.8 469.9 762 370.8 476 429

304.8 304.8 76.2 838.2 841.4 558.8 304.8 *673.1 368.3 567.9 457 511.5 685 616

355.6 336.6 76.2 889.0 892.2 603.3 336.6 *723.9 371.9 609.6 609 537.4 921 827

406.4 387.4 101.6 990.6 993.8 685.8 387.4 *774.7 453.1 668.5 457 629.4 1126 1012

457.2 438.2 101.6 1092.2 1095.4 743.0 438.2 *850.9 489.0 741.7 609 665.2 1354 1218

508.0 489.0 127.0 1193.8 1200.2 812.8 489.0 *901.7 561.6 819.7 609 762.0 1909 1646

558.8 539.8 127.0 1295.4 1304.9 870.0 539.8 *977.9 600.2 914.4 609 800.9 2618 1965

609.6 590.6 127.0 1397.0 1406.5 939.8 590.6 *1066.8 636.3 984.5 762 836.9 3147 2394

660.4 635.0 127.0 1447.8 1460.5 1016.0 635.0 *1130.3 672.8 1060.5 914 872.2 3635 2705

711.2 685.8 190.5 1549.4 1562.1 1073.2 685.8 *1193.8 784.1 1139.4 762 1041.1 4493 3427

762.0 736.6 190.5 1651.0 1663.7 1130.3 736.6 *1244.6 826.3 1216.7 762 1083.3 5329 3968

863.6 831.9 190.5 1930.4 1946.3 1244.6 831.9 *1384.3 893.8 1371.6 1067 1150.9 7263 5766

914.4 8 76.3 1 90.5 2082.8 2098 1314.5 876.3 *1435.1 934.7 1443.5 1067 1191.8 9063 7575

1016.0 977.9 228.6 2032.0 1320.8 977.9 *1651.0 1067.3 1651.0 1067 1407.8 12202 10796

1066.8 1047.8 228.6 2108.2 1403.4 1047.8 *1689.1 1109.0 1752.6 1067 1449.5 13572 11884

1219.2 1181.1 279.4 2387.6 1593.9 1181.1 *2133 1300 1964.2


* Short pattern.





Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

Nom

Diam.mm

Ball

BoreB mm

StemSizemm

Raised

FaceLengthA mm

Ring

JointLengthA mm

Diam.

D1 mm

Diam.

D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

16/31

15


3 2.06 1 14 14.125 8.25 3.13 *11 3.94 5 24 6.34 80 72

4 3.13 1 17 17.125 10.75 4.06 *12.5 5.12 6.75 24 7.44 140 126

6 4.06 1.5 22 22.125 14 6 *14 5.94 8.5 36 8.43 230 207

8 6 1.5 26 26.125 16.5 8 *18 7.91 11.25 36 10.43 570 541

10 8 2 31 31.125 20 10 *21.5 10 15.5 24 12.61 775 697

12 10 2 33 33.125 22 12 *23.5 12.12 18.5 30 14.6 1353 1217

14 12 3 35 35.125 23.75 13.25 *26.5 14.5 22.36 18 20.14 1873 1684

16 13.25 3 39 39.125 27 15.25 *28.5 14.64 24 24 21.16 2300 2068

18 15.25 4 43 43.125 29.25 17.25 *30.5 17.84 26.32 18 24.78 2634 2378

20 17.25 4 47 47.25 32 19.25 *33.5 19.25 29.2 24 26.19 4110 3675

22 19.25 5 51 51.375 34.25 21.25 *35.5 22.11 32.27 24 30 4462 4122

24 21.25 5 55 55.375 37 23.25 *38.5 23.63 36 24 31.53 6117 4457

26 23.25 5 57 57.5 40 25 *42 25.05 38.76 30 32.95 7463 5413

28 25 5 61 61.5 42.25 27 *44.5 26.49 41.75 36 34.34 9002 6652

30 27 7.5 65 65.5 44.5 29 *47 30.87 44.86 30 40.99 10875 8275

32 29 7.5 70 70.625 47 32.75 *49 32.53 47.9 30 42.65 13085 9785

36 32.75 7.5 82 82.625 51.75 34.5 *54.5 35.19 54 42 45.31 17017 13517

42 34.5 7.5 83 55.25 41.25 *56.5 36.8 56.83 42 46.92

76.2 52.3 25.4 355.6 358.8 209.6 79.5 *279.4 100.1 127.0 609 161.0 36 33101.6 79.5 25.4 431.8 435.0 273.1 103.1 *317.5 130.0 171.5 609 189.0 64 57

152.4 103.2 38.1 558.8 562.0 355.6 152.4 *355.6 150.9 215.9 914 214.1 104 94

203.2 152.4 38.1 660.4 663.6 419.1 203.2 *457.2 200.9 285.8 914 264.9 259 245

254.0 203.2 50.8 787.4 790.6 508.0 254.0 *546.1 254.0 393.7 609 320.3 352 316

304.8 254.0 50.8 838.2 841.4 558.8 304.8 *596.9 307.8 469.9 762 370.8 614 552

355.6 304.8 76.2 889.0 892.2 603.3 336.6 *673.1 368.3 567.9 457 511.5 850 764

406.4 336.6 76.2 990.6 993.8 685.8 387.4 *723.9 371.9 609.6 609 537.4 1043 938

457.2 387.4 101.6 1092.2 1095.4 743.0 438.2 *774.7 453.1 668.5 457 629.4 1195 1079

508.0 438.2 101.6 1193.8 1200.2 812.8 489.0 *850.9 489.0 741.7 609 665.2 1864 1667

558.8 489.0 127.0 1295.4 1304.9 870.0 539.8 *901.7 561.6 819.7 609 762.0 2024 1870

609.6 539.8 127.0 1397.0 1406.5 939.8 590.6 *977.7 600.2 914.4 609 800.9 2775 2021

660.4 590.6 127.0 1447.8 1460.5 1016.0 635.0 *1066.8 636.3 984.5 762 836.9 3385 2455

711.2 635.0 127.0 1549.4 1562.1 1073.2 685.8 *1130.3 672.8 1060.5 914 872.2 4083 3017

762.0 685.8 190.5 1651.0 1663.7 1130.3 736.6 *1193.8 784.1 1139.4 762 1041.1 4933 3754

812.8 736.6 190.5 1778.0 1793.9 1193.8 831.9 *1244.6 826.3 1216.7 762 1083.3 5935 4438

914.4 831.9 190.5 2082.8 2098.7 1314.5 876.3 *1384.3 893.8 1371.6 1067 1150.9 7719 6131

1066.8 876.3 190.5 2108.2 1403.4 1047.8 *1435.1 934.7 1443.5 1067 1191.8



* Short pattern.





Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

17/31

2.06

16


2

3 3.13 1.5 15 15.125 9.5 3.13 *13.5 4.88 7 36 7.44 130 117

4 4.06 2 18 18.125 11.5 4.06 *15 6.77 9.25 18 9.76 255 225

6 6 2 24 24.125 15 6 *20 12.4 12.5 24 10.92 675 607

8 8 2 29 29.125 18.5 8 *23.5 10 15.5 30 12.61 1340 1206

10 10 3 33 33.125 21.5 10 *25.5 12.88 18.5 18 18.49 2077 1867

12 12 3 38 38.125 24 12 *29.5 14.5 22.36 24 20.14 3002 2699

14 12.75 5 40.5 40.875 25.25 12.75 *31.5 17.4 24.5 24 25.3 4106 3695

16 14.75 5 44.5 44.875 27.75 14.75 *33.5 19.02 27.25 24 26.92 5112 4592

18 16.75 5 48 48.5 31 16.75 *36.5 20.62 30.07 24 28.51 6600 5940

20 18.625 7.5 52 52.5 33.75 18.625 *38.5 24.22 33.88 24 35.23 8620 7750

24 22.5 7.5 61 61.75 41 22.5 *45 28.07 39.95 30 38.18 12400 11200

30 29 7.5 75 75.875 48.5 29 *52 32.53 49.88 42 42.65 22000 19800

36 34.5 9 90 91.125 57.5 34.5 *59.5 38.64 58.25 52.03 35000 31400

50.8 52.3

76.2 79.5 38.1 381.0 384.2 241.3 79.5 *342.9 124.0 177.8 914 189.0 59 53

101.6 103.1 50.8 457.2 460.4 292.1 103.1 *381.0 172.0 235.0 457 247.9 116 102

152.4 152.4 50.8 609.6 612.8 381.0 152.4 *508.0 315 317.5 609 277.4 306 275

203.2 203.2 50.8 736.6 739.8 469.9 203.2 *596.9 254.0 393.7 762 320.3 608 547

254.0 254.0 76.2 838.2 841.4 546.1 254.0 *647.7 327.2 469.9 457 469.6 942 847

304.8 304.8 76.2 965.2 968.4 609.6 304.8 *749.3 368.3 567.9 609 511.5 1362 1224

355.6 323.9 127.0 1028.7 1038.2 641.4 323.9 *800.1 442.0 622.3 609 642.6 1863 1676

406.4 374.7 127.0 1130.3 1139.8 704.9 347.7 *850.9 483.1 692.2 609 683.8 2319 2083

457.2 425.5 127.0 1219.2 1231.9 787.4 425.5 *927.1 523.7 763.8 609 724.2 2994 2694

609.6 571.5 190.5 1549.4 1568.5 1041.4 571.5 *1143.0 713.0 1014.7 762 969.8 5625 5080

508.0 473.1 190.5 1320.8 1333.5 857.3 473.1 *977.9 615.2 860.6 609 894.8 3910 3515

762.0 736.6 190.5 1905.0 1927.2 1231.9 736.6 * 1320.8 826.3 1267.0 1067 1083.3 9979 8981

914.4 876.3 228.6 2286.0 2314.6 1460.5 876.3 *1511.3 981.5 1479.6 1321.4 15876 14243



* Short pattern.





Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm


G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

18/31

17


3 2.06 1 15 15.125 9.5 3.13 *11 3.94 5 24 6.34 105 94

4 3.13 1.5 18 18.125 11.5 4.06 *13.5 4.88 7 36 7.44 197 177

6 4.06 2 24 24.125 15 6 *15 6.77 9.25 18 9.76 345 297

8 6 2 29 29.125 18.5 8 *20 12.4 12.5 24 10.92 825 742

10 8 2 33 33.125 21.5 10 *23.5 10 15.5 30 12.61 1590 1431

12 10 3 38 38.125 24 12 *25.5 12.88 18.5 18 18.49 2307 2074

14 12 3 40.5 40.875 25.25 12.75 *29.5 14.5 22.36 24 20.14 2893 2801

16 12.75 5 44.5 44.875 27.75 14.75 *31.5 17.4 24.5 24 25.3 4396 3956

76.2 52.3 25.4 381.0 384.2 241.3 79.5 *279.4 100.1 127.0 609 161.0 48 43

101.6 79.5 38.1 457.2 460.4 292.1 103.1 *342.9 124.0 177.8 914 189.0 89 80

152.4 103.1 50.8 609.6 612.8 381.0 152.4 *381.0 172.0 235.0 457 247.9 156 135

203.2 152.4 50.8 736.6 739.8 469.9 203.2 *508.0 315 317.5 609 277.4 374 337

254.0 203.2 50.8 838.2 841.4 546.1 254.0 *596.9 254.0 393.7 762 320.3 721 649

304.8 254.0 76.2 965.2 968.4 609.6 304.8 *647.7 327.2 469.9 457 469.6 1046 940

355.6 304.8 76.2 1028.7 1038.2 641.4 323.9 *749.3 368.3 567.9 609 511.5 1312 1270

406.4 323.9 127.0 1130.3 1139.8 704.9 374.7 *800.1 442.0 622.3 609 642.6 1994 1794

Reduced Opening

Reduced Opening



* Short pattern.





Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1 in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.

Flanged End Size Data for Valve with OperatorNormally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1 mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

19/31

18


2 2.06 1 14.5 14.625 8.5 2.06 *11 3.94 5 24 6.34 95 85

3 3.13 1.5 18.5 18.625 10.5 3.13 *13.5 4.88 7 36 7.44 189 169

4 4.06 2 21.5 21.625 12.25 4.06 *15 6.77 9.25 18 9.76 311 276

6 6 2 27.75 28 15.5 6 *20 12.4 12.5 30 10.92 805 724

8 8 3 32.75 33.125 19 8 *23.5 10.95 16.38 18 16.89 1637 1473

10 10 4 39 39.375 23 10 *25.5 15.15 19.5 18 19.96 2435 2063

12 12 4 44.5 45.125 26.5 12 *29.5 17.31 23.38 24 21.8 3753 3103

14 12.75 5 49.5 50.25 29.5 12.75 *31.5 17.4 26 24 25.3 5208 4102

16 14.75 5 54.5 55.375 32.5 14.75 *33.5 19.02 29.25 30 26.92 6750 5273

18 16.75 7.5 60.5 61.375 36 16.75 *36.5 22.69 31.57 30 33.71 9050 7100

20 18.625 7.5 65.5 66.375 38.75 18.625 *38.5 24.22 34.72 30 35.23 12620 9900

24 22.5 7.5 76.5 77.625 46 22.5 *45 28.07 42.16 48 38.18 18100 14200

50.8 52.3 25.4 368.3 371.5 215.9 52.3 *279.4 100.1 127.0 609 161.0 43 39

76.2 79.5 38.1 469.9 473.1 266.7 79.5 *342.9 124.0 177.8 914 189.0 66 77

101.6 103.1 50.8 546.1 549.3 311.2 103.1 *381.0 172.0 235.0 457 247.9 141 125

152.4 152.4 50.8 704.9 711.2 393.7 152.4 *508.0 315 317.5 762 277.4 365 328

203.2 203.2 76.2 831.9 841.4 482.6 203.2 *596.9 278.1 416.1 457 429.0 743 668

254.0 254.0 101.6 990.6 1000.1 584.2 254.0 *647.7 384.8 495.3 457 507.0 1105 936

304.8 304.8 101.6 1130.3 1146.2 673.1 304.8 *749.3 439.7 593.9 609 553.7 1702 1408355.6 323.9 127.0 1257.3 1276.4 749.3 323.9 *800.1 442.0 660.4 609 642.6 2362 1861

406.4 374.7 127.0 1384.3 1406.5 825.5 374.7 *850.9 483.1 743.0 762 683.8 3062 2392

457.2 425.5 190.5 1536.7 1558.9 914.4 425.5 *927.1 576.3 801.9 762 856.2 4105 3220

508.0 473.1 190.5 1663.7 1685.9 984.3 473.1 *977.9 615.2 881.9 762 894.8 5724 4491

609.6 571.5 190.5 1943.1 1971.7 1168.4 571.5 *1143.0 713.0 1070.9 1219 969.8 8210 6441


* Short pattern.


3705 psi WOG (260.5 kg/cm2)5575 psi TEST (392 kg/cm2)


Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

20/31

19


3 2.06 1 18.5 18.625 10.5 3.13 *11 3.94 5 24 6.34 130 117

4 3.13 1.5 21.5 21.625 12.25 4.06 *13.5 4.88 7 36 7.44 230 207

6 4.06 2 27.75 28 15.5 6 *15 6.77 9.25 18 9.76 450 401

8 6 2 32.75 33.125 19 8 *20 12.4 12.5 30 10.92 1100 990

10 8 3 39 39.375 23 10 *23.5 10.95 16.38 18 16.89 1990 1701

12 10 4 44.5 45.125 26.5 12 *25.5 15.15 19.5 18 19.96 2972 2530

14 12 4 49.5 50.25 29.5 12.75 *29.5 17.31 23.38 24 21.8 3996 3347

16 12.75 5 54.5 55.375 32.5 14.75 *31.5 17.4 26 24 25.3 5875 4382

76.2 52.3 25.4 469.9 473.1 266.7 79.5 *279.4 100.1 127.0 609 161.0 59 53

101.6 79.5 38.1 546.1 549.3 311.2 103.1 *342.9 124.0 177.8 914 189.0 104 94

152.4 103.1 50.8 704.9 711.2 393.7 152.4 *381.0 172.0 235.0 457 247.9 204 182

203.2 152.4 50.8 831.9 841.4 482.6 203.2 *508.0 315 317.5 762 277.4 499 448

254.0 203.2 76.2 990.6 1000.1 584.2 254.0 *596.9 278.1 416.1 457 429.0 903 772

304.8 254.0 101.6 1130.3 1146.2 673.1 304.8 *647.7 384.8 495.3 457 507.0 1348 1148

355.6 304.8 101.6 1257.3 1276.4 749.3 323.9 *749.3 439.7 593.9 609 553.7 1813 1518

406.4 323.9 127.0 1384.3 1406.5 825.5 374.7 *800.1 442.0 660.4 609 642.6 2665 1988

Reduced Opening

Reduced Opening



* Short pattern.


3705 psi WOG (260.5 kg/cm2)5575 psi TEST (392 kg/cm2)


Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1in.

Diam.D2in.

LengthAin.

C.L.To

BottomC

in.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.

Flanged End Size Data for Valve with OperatorNormally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

Flange Weld

WeldEnd

WeldEnd

8/12/2019 TC1191

21/31

20


2 2.06 1 17.75 17.875 9.25 2.06 *15 4.53 5.43 24 7.25 114 94

3 3.13 1.5 22.75 23 12 3.13 *18 5.67 7.5 36 8.94 236 187

4 4.06 2 26.5 26.875 14 4.06 *20 7.24 9.75 24 11.70 471 382

6 6 3 36 36.5 19 6 *24 7.76 13.5 24 13.13 943 737

8 6 3 40.5 40.875 21.75 7.125 *24 7.76 13.5 24 13.13 1297 1017

10 8.875 4 50 50.875 26.5 8.875 *33 14.84 20.87 24 20.00 2922 2166

12 10.5 5 56 56.875 30 10.5 *36 16.615 24.5 30 24.75 4506 3258

8 7.125 4 40.5 40.875 21.75 7.125 *28 12.84 18.11 24 17.88 2094 1676

3 2.06 1 22.75 23 12 3.13 *15 4.53 5.43 24 7.25 156 129

4 3.13 1.5 26.5 26.875 14 4.06 *18 5.67 7.5 36 8.94 286 247

6 4.06 2 36 36.5 19 6 *20 7.24 9.75 24 11.7 638 513

10 7.13 4 50 50.875 26.5 8.875 *28 12.84 18.11 24 17.88 2518 1916

12 8.875 4 56 56.875 30 10.5 *33 14.875 20.87 24 20 3566 2657

Full Opening

Reduced Opening

50.8 52.3 25.4 450.9 454.0 235.0 52.3 *381.0 115 138 609 184.2 52 43

76.2 79.5 38.1 577.9 584.2 304.9 79.5 *457.2 144 190.5 914 227.1 107 85

101.6 103.1 50.8 673.1 682.6 355.6 103.1 *508.0 184 247.7 609 297.2 214 173152.4 152.4 76.2 914.4 927.1 482.6 152.4 *609.6 248 342.9 609 333.5 428 334

203.2 181.0 101.6 1028.7 1038.2 552.5 181.0 *711.2 326 460 609 454.0 950 760

254.0 225.4 101.6 1270.0 1292.2 673.1 225.4 *838.2 377.8 530 609 508.0 1325 983

304.8 266.7 127.0 1422.4 1444.6 762.0 266.7 *914.4 423 622.3 762 628.7 2044 1478

76.2 52.3 25.4 577.9 584.2 304.8 79.5 *381.0 115 138 609 184.2 71 59

101.6 79.5 38.1 673.1 682.6 355.6 103.1 *457.2 144 190.5 914 227.1 130 98

152.4 103.1 50.8 914.4 927.1 482.6 152.4 *508.0 184 247.7 609 297.2 289 233

203.2 152.4 76.2 1028.7 1038.2 552.5 181.0 *609.6 248 342.9 609 333.5 588 461

254.0 181.0 101.6 1270.0 1292.2 673.1 225.4 *711.2 326 460 609 454.0 1142 869

304.8 225.4 101.6 1422.4 1444.6 762.0 266.7 *838.2 377 530 609 508.0 1618 1205

Full Opening

Reduced Opening

Full and Reduced Opening2500 lb. Class






Normally Furnished

Approx. Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

RingJoint

LengthA in.

Diam.D1in.

Diam.D2in.

LengthAin.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.


Normally Furnished

Approx. Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

RaisedFace

LengthA mm

RingJoint

LengthA mm

Diam.D1mm

Diam.D2mm

LengthA

mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

G

H

H

L

E

B

A

C

D1

D2

Flange Weld

WeldEnd

Flange Weld

WeldEnd

8/12/2019 TC1191

22/31

21


2.06 2.06 1 11.625 6.5 2.06 3.94 5 36 6.34 44

3.13 3.13 1 14.124 8.25 3.13 5.12 6.75 36 7.44 85

4.06 4.06 1.5 17.125 10.75 4.06 5.94 8.5 36 8.43 165

7.06 6 2 22.125 14 6 7.91 11.5 24 10.29 445

2.06 2.06 1 14.625 8.5 2.06 3.94 5 36 6.34 90

3.13 3.13 1.5 15.125 9.5 3.13 4.88 7 36 7.44 130

4.06 4.06 2 18.125 11.5 4.06 6.77 9.25 36 9.76 255

7.06 6 2 24.125 15 6 8.39 12.5 30 10.92 675

2.06 2.06 2 14.625 8.5 2.06 3.94 5 36 6.34 953.13 3.13 1.5 18.625 10.5 3.13 4.88 7 36 7.44 189

4.06 4.06 2 21.625 12.25 4.06 6.77 9.25 24 9.30 361

7.06 6 3 28 15.5 6 8.39 13.5 24 13.13 805

52.3 52.3 25.4 295.3 165.1 52.3 100.1 127.0 914 161.0 20

79.5 79.5 25.4 358.8 209.6 79.5 130.0 171.5 914 189.0 39

103.1 103.1 38.1 435.0 273.1 103.1 150.9 215.9 914 214.1 75179.3 152.4 50.8 562.0 355.6 152.4 200.9 292.1 609 262.4 202

52.3 52.3 25.4 371.5 215.9 52.3 100.1 127.0 914 161.0 41

79.5 79.5 38.1 384.2 241.3 79.5 124.0 177.8 914 189.0 59

103.1 103.1 50.8 460.4 292.1 103.1 172.0 235.0 914 247.9 116

179.3 152.4 50.8 612.8 381.0 152.4 213.1 317.5 762 277.4 306

52.3 52.3 25.4 371.5 215.9 52.3 100.1 127.0 914 161.0 43

79.5 79.5 38.1 473.1 266.7 79.5 124.0 177.8 914 189.0 86

103.1 103.1 50.8 549.3 311.2 103.1 172.0 235.0 914 236.2 164

179.3 152.4 76.2 711.2 393.7 152.4 213.1 342.9 609 333.5 365

API Flanged EndFull Opening

Flange

Flanged End (RTJ)Size Data for Valve withOperator Normally

Furnished

Approx.Wt. lb.

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

RaisedFace

LengthA in.

Diam.D1in.

Diam.D2in.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.

Flange


Furnished

Approx.Wt. kg.

NomDiam.mm

BallBoreB mm

StemSizemm

LengthA mm

Diam.D1mm

Diam.D2mm

C.L.To

BottomC

mm

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm

2000 psi W.P. 4000 psi TEST



140.6 kg/cm2 W.P. 281.2 kg/cm2 TEST



G

H

H

L

E

B

A

C

D1

D2

8/12/2019 TC1191

23/31

22


3.13 2.06 1 14.125 8.25 3.13 3.94 5 36 6.34 80

4.06 3.13 1 17.125 10.75 4.06 5.12 6.75 36 7.44 140

7.06 4.06 1.5 22.125 14 6 5.94 8.5 36 8.43 230

3.13 2.06 1 15.125 9.5 3.13 3.94 5 36 6.34 105

4.06 3.13 1.5 18.125 11.5 4.06 4.88 7 36 7.44 197

7.06 4.06 2 24.125 15 6 6.77 9.25 36 9.76 345

3.13 2.06 1 18.625 10.5 3.13 3.94 5 36 6.34 130

4.06 3.13 1.5 21.625 12.25 4.06 4.88 7 36 7.44 230

7.06 4.06 2 28 15.5 6 6.77 9.25 24 9.30 490

API Flanged EndReduced Opening

79.5 52.3 25.4 358.8 209.6 100.1 127.0 914 161.0 38103.1 79.5 25.4 435.0 273.1 130.0 171.5 914 189.0 64

179.3 103.1 38.1 562.0 355.6 150.9 215.9 914 214.1 104

79.5 52.3 25.4 384.2 241.3 100.1 127.0 914 161.0 48103.1 79.5 38.1 460.4 292.1 124.0 177.8 914 189.0 89

179.4 103.1 50.8 612.8 381.0 172.0 235.0 914 247.9 156

79.5 52.3 25.4 473.1 266.7 100.1 127.0 914 161.0 59103.1 79.5 38.1 549.3 311.2 124.0 177.8 914 189.0 104

179.3 103.1 50.8 711.2 393.7 172.0 235.0 609 236.2 222


FurnishedApprox.Wt. lb.Flange

NomDiam.

in.

BallBoreB in.

Stem

Sizein.

LengthA in.

Diam.D1in.

Diam.D2in.

C.L.To

BottomCin.

Body

SphereEin.

Lever

LengthLin.

DiameterHandwheel

for GearGin. H

in.

Size Data for Valve withOperator Normally

Furnished

Approx.Wt. kg.Flange

NomDiam.mm

BallBoreB mm

StemSizemm

C.L.

BodySphere

Emm

LeverLength

Lmm

DiameterHandwheel

for GearG

mm Hmm




79.5

103.1

152.4

79.5

103.1

152.4

79.5

103.1

152.4

LengthA mm

Diam.D1mm

Diam.D2mm

Flanged End (RTJ)




C.L.To

BottomC

in.

G

H

H

L

E

B

A

C

D1

D2

8/12/2019 TC1191

24/31

23

Centerline to Mounting Flange Dimensions

The dimensions on this page, combined with the top

works dimensions on the following two pages, provide the

information required for determining the overall dimensions

of a Cameron ball valve when an actuator is installed.

For additional dimensional information on Cameron ball

valves, contact your Cooper Cameron Valves representative.

Bore Dimension A (in.)

Size ANSI Pressure Class

(in.) 150 300 400 600 900 1500

2 4.06 4.06 4.06 4.06 4.06 4.06

3 5.08 5.08 5.08 5.08 4.76 4.76

4 5.79 5.79 5.79 5.79 6.61 6.61

6 7.64 7.64 7.64 7.64 8.23 8.23

8 9.92 9.92 9.92 9.92 9.92 13.45

10 11.91 11.91 11.91 11.91 15.05 15.96

12 16.70 16.70 16.70 16.70 16.70 17.80

14 17.72 17.72 17.72 17.72 20.55 20.55

16 19.08 19.08 20.78 20.78 22.17 22.17

18 22.19 22.19 22.19 22.19 23.76 27.71

20 23.75 23.75 25.25 25.25 29.23 29.23

22 25.22 25.22 26.78 26.78

24 26.63 26.63 28.20 28.20 32.18 32.18

26 29.59 29.59 29.59 29.59

28 30.97 30.97 30.97 34.99

30 32.62 32.62 32.62 36.65 36.65

34 35.26 35.26 39.31 39.31

36 36.85 40.92 40.92 40.92 44.65

40 44.25 44.25 44.25 48.05

42 45.89 45.89 45.89 49.69

48 50.04 50.04 54.02 56.50


A

Bore Dimension A (mm)

Size ANSI Pressure Class

(mm) 150 300 400 600 900 1500

50.8 103.12 103.12 103.12 103.12 103.12 103.12

76.2 129.03 129.03 129.03 129.03 120.90 120.90

101.6 147.06 147.06 147.06 147.06 167.89 167.89

152.4 194.06 194.06 194.06 194.06 209.04 209.04

203.2 251.97 251.97 251.97 251.97 251.97 341.63

254.0 302.51 302.51 302.51 302.51 382.27 405.38

304.8 424.18 424.18 424.18 424.18 424.18 452.12

355.6 450.09 450.09 450.09 450.09 521.97 521.97

406.4 484.63 484.63 527.81 527.81 563.12 563.12

457.2 563.63 563.63 563.63 563.63 603.50 703.83

508.0 603.25 603.25 641.35 641.35 742.44 742.44

558.8 640.59 640.59 680.21 680.21

609.6 676.40 676.40 716.28 716.28 817.37 817.37

660.4 751.59 751.59 751.59 751.59

711.2 786.64 786.64 786.64 888.75

762.0 828.55 828.55 828.55 930.91 930.91

812.8 895.60 895.60 998.47 998.47

914.4 935.99 1039.37 1039.37 1039.37 1134.11

1016.0 1123.95 1123.95 1123.95 1220.47

1066.8 1165.61 1165.61 1165.61 1262.13

1219.2 1271.12 1271.12 1372.11 1435.10

SD-24030

8/12/2019 TC1191

25/31

24

Notes: -1 and -2 bolt holes straddle centerline

Notes: -3 bolt holes are on centerline

Cameron Ball Valve Square Nut and Adapter Flange Mounting Dimensions (BX-1220)


Cameron Ball Valve Square Nut and Adapter Flange (BX-1220)

Cameron Ball Valve Keyed Shaft and Adapter Flange (BX-1221)

F

B

A

C

D

R

K

V

J

Q

H

S

N

E

F

Dash Number - 1 - 2 - 3

Valve Stem Size 1 1.50 2

A - Flange Dia (in.) 6.50 6.50 8.75

B - Boss Dia (in.) 4.747 4.747 6.997

C - Height of Nut (in.) 1.94 2.12 2.62

D - Bolt Size (in.) 0.44 0.54 0.66

F - Width of Nut (in.) 1.5 2.0 2.5

H - Number of Holes 8 8 16

J - Dia Bolt Circle (in.) 5.75 5.75 8.00

Bolt Size 3/8-16 3/8-16 3/8-16NC-2 NC-2 NC-2

Bolt Torque (ft-lb) 30 30 30

Dash Number - 1 - 2 - 3

Valve Stem Size 25.40 38.10 50.80

A - Flange Dia (mm) 165.10 165.10 222.25

B - Boss Dia (mm) 120.57 120.57 177.72

C - Height of Nut (mm) 49.28 53.85 66.55

D - Bolt Size (mm) 11.18 13.72 16.76

F - Width of Nut (mm) 38.10 30.80 63.50

H - Number of Holes 8 8 16

J - Dia Bolt Circle (mm) 146.05 146.05 203.20

Bolt Size 3/8-16 3/8-16 3/8-16NC-2 NC-2 NC-2

Bolt Torque (NM) 40.68 40.68 40.68

SD-016398

SD-016397

SD-016400 SD-016399

8/12/2019 TC1191

26/31

25

Dash Number - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11

Valve Stem Size 3 4 5 7.5 9 11 13 15

A - Number of Holes 16 16 24 24 24 28 28 32

C - Dia Bolt Circle (in.) 10.375 17.25 18.375 24.00 31.00 27.50 27.50 36.00

E - Max Shaft Dia (in.) 2.745 3.245 4.495 5.495 6.245 8.995 8.995

F - Boss Dia (in.) 9.122 16.246 17.121 21.746 28.308 25.496 25.496 33.496

H - Shaft to Slot ID (in.) 2.402 2.831 3.786 4.803 5.409 7.887 6.774

J - Height of Nut (in.) 4.75 5.310 6.25 8.50 9.13 13.31 13.31 19.25

K - Flange Dia (in.) 11.50 18.25 19.380 25.75 32.75 30.00 30.00 39.00

N - Flange Thickness (in.) 0.63 0.63 0.63 1.00 1.00 1.25 1.25 1.50

Q - Key Width (in.) 0.625 0.75 1.25 1.25 1.50 2.00 2.00 2.25

R - Height of Boss (in.) 3.75 4.310 5.250 7.50 8.13 12.00 12.00 17.50

S - Overall Height (in.) 6.120 7.00 8.120 11.00 11.75 16.12 15.84 21.50

V - Adapter Flange 1.00 1.00 1.00 1.00 1.00 1.25 1.25 1.50V - Thickness (in.)

Flange Bolt Size 1/2-13 1/2-13 1/2-13 7/8-9 7/8-9 1-1/4-8 1-1/4-8 1-1/4-8

NC-2 NC-2 NC-2 NC-2 NC-2 NC-2 NC-2 NC-2

Bolt Torque (ft-lb) 60 60 63 330 330 1000 1000 1600

Notes: -1 and -2 bolt holes straddle centerline

Notes: -3 bolt holes are on centerline

Cameron Ball Valve Keyed Shaft and Adapter Flange Mounting Dimensions (BX-1221)

Notes: -7 through -11 bolt holes straddle centerline

Notes: -4 through -6 bolt holes are on centerline


Dash Number - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11

Valve Stem Size 76.20 101.60 127.00 190.50 228.60 279.40 330.20 381.00

A - Number of Holes 16 16 24 24 24 28 28 32

C - Dia Bolt Circle (mm) 263.53 438.15 466.73 609.60 787.40 698.50 698.50 914.40

E - Max Shaft Dia (mm) 69.73 82.43 114.18 139.58 158.63 228.48 228.48

F - Boss Dia (mm) 231.69 412.64 434.87 552.34 719.02 647.59 647.59 850.79

H - Shaft to Slot ID (mm) 61.01 71.91 96.16 122.00 137.38 200.32 172.05

J - Height of Nut (mm) 120.65 134.88 158.75 215.90 231.91 338.03 338.03 488.95K - Flange Dia (mm) 292.10 463.55 492.26 654.05 831.85 762.00 763.00 990.60

N - Flange Thickness (mm) 16.00 16.00 16.00 25.40 25.40 31.75 31.75 38.10

Q - Key Width (mm) 15.88 19.05 31.75 31.75 38.10 50.80 50.80 57.15

R - Height of Boss (mm) 95.25 109.48 133.35 190.50 206.51 304.80 304.80 444.50

S - Overall Height (mm) 155.45 177.80 206.25 279.40 298.45 409.45 402.34 546.10

V - Adapter Flange 25.40 25.40 25.40 25.40 25.40 31.75 31.75 38.10V - Thickness (mm)

Flange Bolt Size 1/2-13 1/2-13 1/2-13 7/8-9 7/8-9 1-1/4-8 1-1/4-8 1-1/4-8

NC-2 NC-2 NC-2 NC-2 NC-2 NC-2 NC-2 NC-2

Bolt Torque (NM) 81 81 85 447 447 1356 1356 2169

8/12/2019 TC1191

27/31

26

Q

M

P

N

P

N

M

Q

M

N

Q

P

M

N

Q

P

N

P

MM

N

Q

P

Q

R

Stem Effective No. OfSize Model Ratio Turns M N P Q R(in.) Per 90 (in.) (in.) (in.) (in.) (in.)

1.5 MG 11:1 11.5 3.63 4.37 1.81 3.38

2 MG 18.3:1 18.0 4.75 5.00 2.31 5.38

3* DT 11:1 11.5 5.75 7.53 4.21 4.63 4.05

Manual Gear Dimensions for Cameron Ball Valves Manufactured in U.S.

Manual Gear Dimensions for Cameron Ball Valves Manufactured in France

Manual Gear Dimensions for Cameron Ball Valves 3 and Larger

Model WG1/B6 Model WG1/S12

Model RC431Model RC250

Mastergear Dynatorque


SD-24020 SD-24021

SD-24023SD-24022

SD-24024 SD-24025

*Normally furnished in above ground applications

Stem Effective No. OfSize Model Ratio Turns M N P Q R(in.) Per 90 (mm) (mm) (mm) (mm) (mm)

1.5 MG 11:1 11.5 92.20 111.00 45.97 85.85

2 MG 18.3:1 18.0 120.65 127.00 58.67 136.65

3* DT 11:1 11.5 146.05 1 91.26 1 06.93 1 17.60 102.87

Stem Effective No. OfSize Model Ratio Turns M N P Q(in.) Per 90 (in.) (in.) (in.) (in.)

1 250 11:1 11.5 3.27 5.12 2.17 3.76

1.5 250 11:1 11.5 3.27 5.12 2.17 3.76

2 431 22:1 18 4.39 5.67 4.21 5.43

Stem Effective No. OfSize Model Ratio Turns M N P Q(in.) Per 90 (mm) (mm) (mm) (mm)

1 250 11:1 11.5 83.06 130.05 55.12 92.27

1.5 250 11:1 11.5 83.06 130.05 55.12 92.27

2 431 22:1 18 111.51 144.02 144.02 137.92


3 1/B6 55:1 60 5.75 7.56 4.11 12.64

4 1/B6 110:1 112.5 9.13 8.69 4.69 12.64

5 1/S12 153:1 190 9.69 10.25 5.50 9.50

7.5 1/S12 297:1 297 12.88 12.63 6.63 14.00

9 1/S12 432:1 428 16.38 14.77 7.39 19.50


3 1/B6 55:1 60 146.05 192.02 104.39 321.06

4 1/B6 110:1 112.5 236.22 220.73 119.30 321.06

5 1/S12 153:1 190 246.13 260.35 137.70 241.30

7.5 1/S12 297:1 297 327.15 320.80 168.40 355.60

9 1/S12 432:1 428 416.05 375.16 187.71 495.30

8/12/2019 TC1191

28/31

DIMENSIONS OF WELDED AND SEAMLESS PIPE

Nominal Wall Thickness and Inside Diameter

Nominal Outside Wall Schedule Schedule Schedule Standard Schedule Schedule Extra Schedule Schedule Schedule Schedule Schedule Dbl Ex.Pipe Size Diameter I.D. 10 20 30 Weight 40 60 Strong 80 100 120 140 160 Strong

1/8 .405Wall .049 .068 .068 .095 .095

I.D. .307 .269 .269 .215 .215

1/4 .540Wall .065 .088 .088 .119 .119

I.D. .410 .364 .364 .302 .302

3/8 .675Wall .065 .091 .091 .126 .126

I.D. .545 .493 .493 .423 .423

1/2 .840Wall .083 .109 .109 .147 .147 .187 .294

I.D. .670 .622 .622 .546 .546 .466 .252

3/4 1.050Wall .083 .113 .113 .154 .154 .218 .308

I.D. .113 .824 .824 .742 .742 .614 .434

1 1.315Wall .109 .113 .113 .179 .179 .250 .358

I.D. 1.097 1.049 1.049 .957 .957 .815 .599

11/4 1.660Wall .109 .140 .140 .191 .191 .250 .382

I.D. 1.442 1.380 1.380 1.278 1.278 1.160 .896

11/2 1.900Wall .109 .145 .145 .200 .200 .281 .400

I.D. 1.682 1.610 1.610 1.500 1.500 1.338 1.100

2 2.375Wall .109 .154 .154 .218 .218 .343 .436

I.D. 2.157 2.067 2.067 1.939 1.939 1.689 1.503

21/2 2.875Wall .120 .203 .203 .276 .276 .375 .552

I.D. 2.635 2.469 2.469 2.393 2.323 2.125 1.771

3 3.500Wall .120 .216 .216 .300 .300 .438 .600

I.D. 3.260 3.068 3.068 2.900 2.900 2.624 2.300

31/2 4.000Wall .120 .226 .226 .318 .318 .636

I.D. 3.760 3.548 3.548 3.364 3.364 2.728

4 4.500Wall .120 .237 .237 .337 .337 .438 .531 .674

I.D. 4.260 4.026 4.026 3.826 3.826 3.624 3.438 3.152

5 5.563Wall .134 .258 .258 .375 .375 .500 .625 .750

I.D. 5.295 5.047 5.047 4.813 4.813 4.563 4.313 4.063

6 6.625Wall .134 .280 .280 .432

Date post:	03-Jun-2018
Category:	Documents
Upload:	boris-zaslichko
View:	220 times
Download:	0 times

TC1191

Documents