B B E E L L L L I I N N Z Z O O N N I I ® BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]Mastic 2000 polyester technical bulletin index Descriprition fm to Brochure of the product Page 2 Page 3 Mastic 2000 straw yellow liquid (flowing) Page 4 Page 5 Mastic 2000 straw yellow vertical (solid / knife grade) Page 6 Page 7 Mastic 2000 coloured liquid (flowing) Page 8 Page 9 Mastic 2000 coloured vertical (solid / knife grade) Page 10 Page 11 Mastic 2000 transparent liquid (flowing) Page 12 Page 13 Mastic 2000 transparent vertical (solid / knife grade) Page 14 Page 15 Hardeners Page 16 Page 18 – http://www.bellinzoni.com
Transcript
BBEELLLLIINNZZOONNII®
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
Mastice per marmi e pietre bi componente a base di resine poliesteri insature. La innovativa formulaconsente un impiego inferiore di solventi privilegiando la sicurezza durante l’utilizzo. Grazieall’impiego di resine poliesteri di eccellente qualità, l’adesione del mastice alla pietra è aumentatadel 23%. E’ disponibile in versione liquida e solida per qualsiasi esigenza.
Two-component polyester resin mastic for marble and stone. With its innovative formula it is possible touse lower quantity of solvents therefore making its usage safer. It contains polyester resin of excellentquality therefore the adhesion of the mastic to the stone has improved by 23%. Available in liquid andsolid form for every necessity.
Where to apply: Marble, granite, limestone, sandstone, slates
01 02 03
04 05 06
07 08 09
10 11 12
Modo d’uso: Le parti da incollare o stuccare devono essere pulite, perfettamente asciutte eprive di polvere. Aggiungere al mastice il 2% in peso del catalizzatore, mescolareaccuratamente ed applicare avendo cura di far aderire bene il mastice al supporto,esercitando con la spatola una leggera pressione. A indurimento avvenuto, il mastice èlevigabile e lucidabile dopo circa due ore con gli stessi attrezzi impiegati per lavorare lapietra. Spessori consigliati: nella stuccatura di superfici particolarmente estese non superarei 5 mm per ogni applicazione. Per spessori maggiori, eseguire più applicazioni.
Usage: The surfaces to be treated must be clean, fully dry and dust free. Add to the mastic 2%of hardener in weight mix thoroughly and apply making sure the mixture is properly applied onthe surface by using a little pressure on the spatula. After a couple of hours, when hardened, it ispossible to grind and polish with the standard tools used in stone processing. Recommended thickness:in big areas not more than 5mm at a time and for more thickness apply in several layers.
Dati tecnici: Essendo i dati tecnici differenti a seconda della versione sia essa Liquida o Solida e aseconda della colorazione, sono disponibili schede tecniche per ogni prodotto.
Technical data: Technical sheets are available for different types depending on types: liquid or solid,transparent or coloured.
Resa del prodotto: La resa del prodotto dipende molto dal tipo di applicazione se si tratta diincollaggio, stuccatura ecc... Non è pertanto possibile fornire un dato attendibile.
Output: Exact details are not available because its usage much depends on the type of application, ifused for gluing, filling etc.
Confezioni: Mastici colorati: Cartoni da 9 barattoli da kg.1,600, cartoni da 2 barattoli da kg.7,fusti da kg.28,50Mastici trasparenti: Cartoni da 9 barattoli da kg.1,050, cartoni da 2 barattoli da kg. 4,150,fusti da kg.18,50
Packing: Coloured mastics: 9 sets of 1.6kg/set per carton - 2sets of 7kg/set per carton1 set of 28.5kg/setTransparent mastics: 9sets of 1.05kg/set per carton - 2 sets of 4.15kg/set per carton1set of 28.5kg/set
20016 PERO - MILANO ITALY U.E. - Via Don Gnocchi, 4 - Tel. +39 0233912133 - Fax +39 0233915224Internet: http://www.bellinzoni.com - E-mail: [email protected]
Since 1937
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 STRAW YELLOW LIQUID (BEIGE – BUFF FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based of unsatured polyester resins. It hardens quickly after adding its hardener. It has good adhesive power and thanks to its fluidity, it penetrates into the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It is possible to alter the colour by adding Bellinzoni colour paste tubes or colour oxide powders. It is resistant to most of the chemicals such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance Liquid Colour available 02 Light straw yellow
03 Straw yellow 04 Dark straw yellow
Odour Characteristic Specific gravity at 20°C (68° F) 1,76 ± 0,01 Hydro-solubility Insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strength at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight [Check technical bulletin for hardener for more information] Mpa 5.200 ± 479 Mpa 32,5 ± 2,1 0,6 ± 0,1 % Mpa 6.300 ± 320 Mpa 54,5 ± 4,5 1,1 ± 0,1 % 6 months in its original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add 2% of paste hardener in weight to the mastic, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season, it is possible to increase quantity of hardener up to 3%. Once hardened after a couple of hours, the mastic can be grinded and polished. For materials with porosity or holes very big (Travertine) we suggest to make a second application.
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 STRAW YELLOW LIQUID (BEIGE – BUFF FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use: • Do not use the hardener in quantity more than 4% as it will reduce adhesion of the product and also
reduces the working time and could cause a color variation. • Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the
mastic will dry quickly. • Do not use hardener in quantity less than 1% and/or at low temperature (below 5° C – 41°F) which
makes catalyzation time very long. • Do not use the coloring paste in quantity more than 2% as it could prejudice the adhesion. • After the mixing with hardener, the product has a working time between 3 and 15 minutes. • Stone can be moved after 20 minutes from treatment. • Read carefully recommendations printed on the tin before use.
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboards of: 9 tins of 1,600 kg (56 oz) , 2 tins of 7 kg (15,40 lb); 1 tin of 28,50 kg (62,80 lb) hardener included.
The composition of the tins is Steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed to the U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.); for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Harmonised Custom Tariff:
3214.10.10
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 STRAW YELLOW VERTICAL (BEIGE – BUFF KNIFE GRADE) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based on unsatured polyester resins. It hardens quickly after adding its hardener. It has good adhesive power and thanks to its fluidity, it penetrates into the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It is possible to alter the colour by adding Bellinzoni colour paste tubes or colour oxide powders. It is resistant to most of the chemicals such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance Paste Colour available 02 Light straw yellow
03 Straw yellow 04 Dark straw yellow
Odour Characteristic Specific gravity at 20°C (68° F) 1,65 ± 0,01 Hydro-solubility Insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strength at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight [Check technical bulletin for hardener for more informatin] Mpa 6,950 ± 768 Mpa 26,6 ± 1,7 0,4 ± 0,1 % Mpa 7,580 ± 150 Mpa 54,5 ± 3,4 0,9 ± 0,1 % 6 months in its original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add 2% of paste hardener in weight to the mastic, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season, it is possible to increase quantity of hardener up to 3%. Once hardened after a couple of hours, the mastic can be grinded and polished. For materials with porosities or holes very big (Travertine) we suggest to make a second application.
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 STRAW YELLOW VERTICAL (BEIGE – BUFF KNIFE GRADE) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use:
• Do not use the hardener more than 4% as it will reduce adhesion of the product and also reduces the working time and could cause a color variation.
• Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the mastic will dry quickly.
• Do not use hardener in quantity less than 1% and/or at low temperature (below 5° C – 41°F) which makes catalyzation time very long.
• Do not use the coloring paste in quantity more than 2% as it could prejudice the adhesion. • After the mixing with hardener, the product has a working time between 3 and 15 minutes. • Stone can be moved after 20 minutes from treatment. • Read carefully recommendations printed on the tin before use.
Application on surfaces: Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, resin marble, concrete.
Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboards of: 9 tins of 1,600 kg (56 oz) , 2 tins of 7 kg (15,40 lb); 1 tin of 28,50 kg (62,80 lb) hardener included. The composition of the tins is steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.); for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Harmonized Custom Tariff:
3214.10.10
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 COLOURED LIQUID (FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based on unsatured polyester resins. It hardens quickly adding its hardener. It has good adhesive power, its fluidity allow to penetrates in the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It can be colored using paste coloring tubes Bellinzoni and coloring oxide powders. It is resistant to the most of chemical products such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance liquid Colour available 01 White
12 Black Odour characteristic Specific gravity at 20°C (68° F) 1,76 ± 0,01 Hydro-solubility insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strength at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight [Check technical bulletin for hardener for more information] Mpa 5.200± 479 Mpa 32,5 ± 2,1 06 ± 0,1 % Mpa 6.300 ± 320 Mpa 54,5 ± 4,5 1,1 ± 0,1 % 6 months in its original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add 2% of paste hardener in weight to the mastic, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season is possible to increase hardener up to 3%. Once hardened after a couple of hours, the mastic can be grinded and polished. For materials with porosity or holes very big (Travertine) we suggest to make a second application.
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 COLOURED LIQUID (FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use: • Do not use the hardener more than 4% as it will reduce adhesion of the product. It also reduces working
time and could cause a colour variation. • Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the
mastic will dry too quickly. • Do not use hardener in quantity less than 1% and/or at low temperature [below 5° C (41°F)] which makes
catalyzation time very long. • Do not use the colouring paste in quantity more than 2%, which could prejudice the adhesion. • After mixing with hardener, the product has a working time between 3 and 15 minutes. • Stone can be moved after 20 minutes from treatment. • Read carefully recommendations printed on the tin before use.
Application on surfaces: Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, resin marble, concrete.
Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboards of: 9 tins of 1,600 kg (56 oz) , 2 tins of 7 kg (15,40 lb); 1 tin of 28,50 kg (62,80 lb) hardener included The composition of the tins is steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.); for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Harmonised Custom Tariff:
3214.10.10
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin “MASTIC 2000” COLOURED VERTICAL (KNIFE GRADE- SOLID) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based on unsatured polyester resins. It hardens quickly adding its hardener. It has good adhesive power, it is perfectly transparent and with its fluidity, penetrates in the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It can be colored using paste coloring tubes Bellinzoni and coloring oxide powders. It is resistant to the most of chemical products such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance Tixotropic paste (knifegrade) Colour available 01 White
05 Svilari 06 Ochre yellow 07 Carnic gray 08 Partridge gray 09 Assisi red 10 Verona red 11 Green 12 Black
Odor characteristic Specific gravity at 20°C (68° F) 1,65 ± 0,01 Hydro-solubility insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strenght at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight for more information [Chech technical bulletin for hardener] Mpa 6950 ± 768 Mpa 26,6 ± 1,7 0,4 ± 0,1 % Mpa 7580 ± 150 Mpa 54,4 ± 3,4 0,9 ± 0,1 % 6 months in original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add to the mastic 2% of paste hardener in weight, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season is possible to increase hardener quantity till 3%. Once hardened after a couple of hours, the stone and the mastic can be grinded an polished.
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin “MASTIC 2000” COLOURED VERTICAL (KNIFE GRADE- SOLID) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use: • Do not use the hardener more than 4%, it will reduce adhesion of the product. It reduces also working
time and could cause a color variation. • Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the
mastic will dry too fast. • Do not use hardener in quantity less than 1% and/or at low temperature [below 5° C (41°F)] which
makes catalyzation time very long. • Do not use the coloring paste in quantity more than 2% could prejudice the adhesion • After the mixing with hardener, the product has a work-time between 3 and 15 minutes. • Stone can be moved after 20 minutes from filling. • Read carefully recommendations printed on the tin before use.
Application on surfaces: Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, resin marble, concrete.
Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboards of: 9 tins of 1,600 kg (56 oz) , 2 tins of 7 kg (15,40 lb); 1 tin of 28,50 kg (62,80 lb) hardener included. The composition of the tins is Steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.) for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Custom Tariff:
3214.10.10
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 TRANSPARENT LIQUID (TRANSPARENT FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based of unsatured polyester resins. It hardens quickly after adding its hardener. It has good adhesive power and it is perfectly transparent and thanks to its fluidity, it penetrates into the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It can be coloured by using Bellinzoni colour paste tubes and colour oxide powders. It is resistant to most of the chemicals such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance liquid Colour available 00 Transparent (honey colour) Odour characteristic Specific gravity at 20°C (68° F) 1,10 ± 0,01 Hydro-solubility insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strength at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight [Check technical bulletin for hardener for more information] Mpa 2.400± 323 Mpa 40,9 ± 2,4 2,2 ± 0,2 % Mpa 2.480 ± 74 Mpa 72,3 ± 8,7 3,9 ± 0,5 % 6 months in its original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add 2% of paste hardener in weight to the mastic, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season, it is possible to increase quantity of hardener up to 3%. Once hardened after a couple of hours, the mastic can be grinded and polished. For materials with porosity or holes very big (Travertine) we suggest to make a second application.
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 TRANSPARENT LIQUID (TRANSPARENT FLOWING) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected]
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use: • Do not use the hardener more than 4% as it will reduce adhesion of the product and also reduces the
working time and could cause a color variation. • Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the
mastic will dry quickly. • Do not use hardener in quantity less than 1% and/or at low temperature (below 5° C – 41°F) which
makes canalization time very long. • Do not use the coloring paste in quantity more than 2% as it could prejudice the adhesion. • After the mixing with hardener, the product has a working time between 3 and 15 minutes. • Stone can be moved after 20 minutes from treatment. • Read carefully recommendations printed on the tin before use.
Application on surfaces: Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, resin marble, concrete.
Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboard of: 9 tins of 1,05 kg (37 oz), 2 tins of 4.15 kg (9,15 lb); 1 tin of 18.50kg (40,80 lb) hardener included. The composition of the tins is steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.);for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Harmonised Custom Tariff:
3214.10.10
– http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 TRANSPARENT VERTICAL (KNIFEGRADE - SOLID) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
Two pack mastic for marble and stone, based of unsatured polyester resins. It hardens quickly after adding its hardener. It has good adhesive power and it is perfectly transparent and thanks to its fluidity, it penetrates into the hollowness and porosity of the stone. After hardening, it can be worked as the stone. It can be coloured by using Bellinzoni colour paste tubes and colour oxide powders. It is resistant to most of the chemicals such as oils, fats, detergents, solvents, etc.
Technical Characteristics:
Appearance Tixotropic paste (knifegrade) Colour available 00 Transparent (honey colour) Odour characteristic Specific gravity at 20°C (68° F) 1,10 ± 0,01 Hydro-solubility insoluble pH Catalysis ratio: Bending tension ASTM D638: Elasticity modulus Breaking Tension Deformation at break Bending flexion ASTM D790: Elasticity modulus Maximum strength at break Deformation at break Shelf life at 20° C (68° F)
n.a. 2% in weight [Check technical bulletin for hardener for more information] Mpa 2.400± 323 Mpa 36,1 ± 2,4 1,9 ± 0,2 % Mpa 2.570 ± 74 Mpa 69,5 ± 7,8 3,3 ± 0,5 % 6 months in its original packing
Instruction for Use:
The area to be glued or filled must be clean, perfectly dry and dust free. Add 2% of paste hardener in weight to the mastic, mix thoroughly until a homogeneous mass is obtained and apply with a spatula on horizontal or vertical surface. In cold season, it is possible to increase quantity of hardener up to 3%. Once hardened after a couple of hours, the mastic can be grinded and polished. For materials with porosity or holes very big (Travertine) we suggest to make a second application.
BBEELLLLIINNZZOONNII®
Technical Bulletin MASTIC 2000 TRANSPARENT VERTICAL (KNIFEGRADE - SOLID) Two component polyester mastic for marble and stones
Revised 01-2006 RV/ARB
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Suggestion for Use: • Do not use the hardener more than 4% as it will reduce adhesion of the product and also reduces the
working time and could cause a color variation. • Never catalyze the total quantity of the mastic at one time in order to avoid “mass effect” because the
mastic will dry quickly. • Do not use hardener in quantity less than 1% and/or at low temperature (below 5° C – 41°F) which
makes canalization time very long. • Do not use the coloring paste in quantity more than 2% as it could prejudice the adhesion. • After the mixing with hardener, the product has a working time between 3 and 15 minutes. • Stone can be moved after 20 minutes from treatment. • Read carefully recommendations printed on the tin before use.
Application on surfaces: Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, resin marble, concrete.
Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing: Cardboard of: 9 tins of 1,05 kg (37 oz), 2 tins of 4.15 kg (9,15 lb); 1 tin of 18.50kg (40,80 lb) hardener included. The composition of the tins is steel (ACC). After use, comply with the local and national regulations currently in force regarding recycling. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.);for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
Harmonised Custom Tariff:
3214.10.10
BBEELLLLIINNZZOONNII®
Technical Bulletin HARDENER FOR POLYESTER MASTICS
Revised 01-2006 RV/ARB
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Description:
The proper usage of the hardener with polyester mastic is very important in order to obtain the proper solidification effect and if not used correctly it may spoil your work. This brief manual is for the user to understand how much hardener he has to use depending on the type of resin and job to do.
1. White paste hardener P.B.O. (Mastic 2000, Spezial Tak & Blitz)
Technical Characteristics:
Appearance cream Colour white Odour characteristic Specific gravity at 20°C 1,21 ± 0,02 Hydro-solubility insoluble PH Shelf life at 20° C (68° F)
n.a. 6 months in original packing
Instruction for Use:
Add 2% hardener to the resin – in weight – mix well and proceed to the application of this mixture. In cold temperature it is possible to increase the hardener up to 3%. Too much hardener can sensibly reduce the working time for the mixing and this will result in the resin to change colour. Never mix an entire tin at the same time just mix smaller quantities. The quantity of the paste hardener to be used can be in weight or in centimetres, see below table.
MEDIUM WORM TEMPERATURE/ MORE THAN 20° C (68° F)
COLD TEMPERATURE/ 5° C (41° F) TO 20° C (68°F)
HARDENING REACTION WITH 2%
HARDENING REACTION WITH 3%
Quantity of mastic in weight (ounces)
Quantity of hardener in Weight (ounces)
Quantity of hardener in Cm (inches)
Quantity of mastic in weight (ounces)
Quantity of hardener in Weight (ounces)
Quantity of hardener in Cm (inches)
25 g (0.9 oz) 0,50 g (0,018 oz) 0,625 (0,25 in) 25 g (0.9 oz) 0,75 g (0,025 oz) 0,937 (0,38 in)50 g (1,8 oz) 1,00 g (0,036 oz) 1,250 (0,50 in) 50 g (1,8 oz) 1,50 g (0,054 oz) 1,875 (0,75 in)75 g (2,6 oz) 1,50 g (0,054 oz) 1,875 (0,75 in) 75 g (2,6 oz) 2.25 g (0,081 oz) 2,812 (1,13 in)
100 g (3,5 oz) 2,00 g (0,072 oz) 2,500 (1,00 in) 100 g (3,5 oz) 3,00 g (0,108 oz) 3,750 (1,50 in) 150 g (5,3 oz) 3,00 g (0,108 oz) 3,750 (1,50 in) 150 g (5,3 oz) 4,50 g (0,162 oz) 5,625 (2,63 in)200 g (7,0 oz) 4,00 g (0,144 oz) 5,000 (2,00 in) 200 g (7,0 oz) 6,00 g (0,216 oz) 7,500 (3,00 in)
Appearance cream Colour Clear transparent Odour Characteristic Specific gravity at 20°C 1,09 ± 0,01 Hydro-solubility Insoluble PH Shelf life at 20° C (68° F)
n.a. 6 months in original packing
BBEELLLLIINNZZOONNII®
Technical Bulletin HARDENER FOR POLYESTER MASTICS
Revised 01-2006 RV/ARB
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
Instruction for Use:
Add 4% hardener to the resin – in weight – mix well and proceed to the application of this mixture. In cold temperature it is possible to increase the hardener up to 5%. Too much hardener can sensibly reduce the working time for the mixing and this will result in the resin to change colour. Never mix an entire tin at the same time just mix smaller quantities. The quantity of the paste hardener to be used can be in weight or in centimetres, see below table.
MEDIUM WORM TEMPERATURE/ MORE THAN 20° C (68° F)
COLD TEMPERATURE/ 5° C (41° F) TO 20° C (68°F)
HARDENING REACTION WITH 4%
HARDENING REACTION WITH 5%
Quantity of mastic in weight (ounces)
Quantity of hardener in Weight (ounces)
Quantity of hardener in Cm (inches)
Quantity of mastic in weight (ounces)
Quantity of hardener in Weight (ounces)
Quantity of hardener in Cm (inches)
25 g (0.9 oz) 1,00 g (0,036 oz) 1,25 (0,50 in) 25 g (0.9 oz) 1,25 g (0,045 oz) 1,50 (0,60 in)50 g (1,8 oz) 2,00 g (0,072 oz) 2,50 (1,00 in) 50 g (1,8 oz) 2,50 g (0,090 oz) 3,00 (1,20 in)75 g (2,6 oz) 3,00 g (0,108 oz) 3,75 (1,50 in) 75 g (2,6 oz) 3,75 g ( 0,135 oz) 4,50 (1,80 in)
100 g (3,5 oz) 4,00 g (0,144 oz) 5,00 (2,00 in) 100 g (3,5 oz) 5,00 g ( 0,180 oz) 6,00 (2,40 in)150 g (5,3 oz) 6,00 g (0,216 oz) 6,25 (2,50 in) 150 g (5,3 oz) 7,50 g ( 0,270 oz) 7,50 (3,00 in)200 g (7,0 oz) 8,00 g (0,288 oz) 7,50 (3,50 in) 200 g (7,0 oz) 10,00 g ( 0,360 oz) 9,00 (4,80 in)
One tablespoon contain approx 16 gr (0,58 oz) of hardener
3. Clear transparent liquid hardener (Astra 24k liquid) Description: This brief manual is for the user to understand how much hardener he has to use depending on the type of resin and job to do. The liquid hardener is supplied in a kit together with Mastic ASTRA 24K LIQUID. It is however possible to use the liquid hardener for NEW THASSOS and ASTRA 24 VERTICAL as well.
Technical Characteristics:
Appearance Liquid Colour Clear transparent Odour Characteristic Specific gravity at 20°C 1,08 ± 0,01 Hydro-solubility Insoluble PH Shelf life at 20° C (68° F)
n.a. 6 months in original packing
Usage: add 4% of the special hardener to the resin – in weight – mix well and proceed to the application of this mixture. In cold temperature, it is possible to increase the hardener quantity to 5%. Too much hardener can sensibly shorten the working time for the mixing and this will result in the resin to change colour (yellowish). Never mix an entire tin at the same time, just mix smaller quantities. The quantity of the paste hardener to be used can be in weight or in centimetres, see below table.
BBEELLLLIINNZZOONNII®
Technical Bulletin HARDENER FOR POLYESTER MASTICS
Revised 01-2006 RV/ARB
All data indicated in this leaflet are the results of tests and experiments carried out in our laboratories and through reliable operators in the stonebusiness and have to be considered reliable. Because of the many factors which can influence them, the information here reported do notconstitute implicit or formal guarantees. The end user undertakes the responsibility in the usage of the product making sure to experiment theproduct characteristic as preventive measure.
BELLINZONI srl - Via Don Gnocchi 4 – 20016 PERO (MI) ITALIA E.U. Tel. +39-0233912133 – Fax +39-0233915224 – e-mail: [email protected] – http://www.bellinzoni.com
MMAA
SSTTII CC
II –– MM
AASSTTII CC
SS ––
MMAA
SSII LL LL AA
SS ––
MMAA
SSTTII QQ
UUEESS -- SS
TTEEII NN
KKII TT
TTEE
MEDIUM TEMPERATURE/ ABOVE AND MORE THAN 15° C (59° F)
COLD TEMPERATURE/ 0° C (32°F) TO 10° C (50°F)
HARDENING REACTION WITH 4% HARDENING REACTION WITH 5% Quantity of mastic in weight
Quantity of hardener in weight
Quantity of hardener in drops
Quantity of mastic in weight
Quantity of hardener in weight
Quantity of hardener in drops
25 g (0.9 oz) 1,00 g (0,036 oz) 40 drops 25 g (0.9 oz) 1,25 g (0,045 oz) 50 drops50 g (1,8 oz) 2,00 g (0,072 oz) 80 drops 50 g (1,8 oz) 2,50 g (0,090 oz) 100 drops75 g (2,6 oz) 3,00 g (0,108 oz) 120 drops 75 g (2,6 oz) 3,75 g ( 0,135 oz) 150 drops
100 g (3,5 oz) 4,00 g (0,144 oz) 160 drops 100 g (3,5 oz) 5,00 g ( 0,180 oz) 200 drops150 g (5,3 oz) 6,00 g (0,216 oz) 200 drops 150 g (5,3 oz) 7,50 g ( 0,270 oz) 300 drops200 g (7,0 oz) 8,00 g (0,288 oz) 300 drops 200 g (7,0 oz) 10,00 g ( 0,360 oz) 400 drops Suggestion for Use:
• Excessive addition of hardener in weight will reduce the gluing properties of the mixture precluding goods results. Moreover when too much hardener is used the mastic once hardened will change colour.
• Too little hardener below 1% will not allow the polymerisation to happen therefore the resin will not harden and will just remain a sticky mass precluding goods resutls.
• When working protect the eyes, hand and all exposed sensitive part of the body. • Never mix different hardeners together after ahving added one hardener to the resin. • When using colouring such as BELLINZONI colour paste or powders add the hardener at the last
moment after the colouring of the resin has been completed. • The information in this leaflet are obtained from our laboratory test and actual usage by experienced
stone processing people and if not comprehensive or for any further request our technical office is at full disposal for further information.
• Read carefully recommendations printed on the tin before use. Safety procedures:
As far as the proper working procedures is concerned, we recommend to consult Material Safety Data Sheets issued according to E.U. rules and to follow your national laws concerning safety in the working place.
Packing:
Hardeners are supplied in kit with mastic, packing for extra hardeners: Hardener white paste 50 pcs hardener of 30 and 50 gr - 20 pcs hardener of 150 gr - 6 pcs hardener of 500 gr Transparent clear paste: 50 pcs hardener 40 gr Liquid transparent hardener 50 pcs hardener 40 gr For bigger packing contact us. Our packing is conformed as per U.N. rules for inland transport (A.D.R.) and by sea (I.M.O.) for transportation via air refer to updated rules (I.A.T.A.). For further information regarding transport please check MSDS.
