of 14
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
1/14
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
2/142
Technical Data
EngineRating per ISO 9249______________ 99 kW (135 HP) at 2000 RPMModel __________________________________ Liebherr D 924 T-EType ____________________________________ 4 cylinder in-line
Bore/stroke ____________________ 4.8/5.6Displacement__________________ 1.74 gal
Engine operation __________________ 4-stroke dieseldirect injection
turbo-chargedreduced emissions
Cooling system ____________________water radiator with integratedengine oil cooler
Air cleaner __________________________ dry-type air cleaner with precleaner,primary and safety elements
Fuel tank______________________________ 63 galEngine idling________________________ sensor controlledElectrical system
Voltage __________________________ 24 VBatteries ________________________ 2 x 92 Ah/12 VStarter____________________________ 24 V/5.4 kW
Alternator ______________________ 24 V/55 Amp
Hydraulic SystemHydraulic pump____________________ Liebherr, variable displacement,
swashplate pumpMax. flow________________________ 79 gal/min.Max. hydr. pressure ________ 5075 PSI
Hydraulic pumpregulation and control __________ Liebherr-Synchro-Comfort-system
(LSC) with electronic engine speedsensing regulation, pressure andflow compensation, load sensingand torque controlled swing drivepriority
Hydraulic tank capacity ________ 52 galHydraulic system capacity ____ max. 103 galFiltration______________________________ one main return filter with integrated
partial micro filtration (5 mm)Cooling________________________________ combined with engine radiator;
thermostatically controlledModes__________________________________ four fixed modes, can also be adjusted
by the operator to adjust engineand hydraulic performance to match
job conditions (Note: All modesprovide full max. power)
LIFT ______________________________ for precise lifting tasksFINE______________________________ for precision work at high speed
i.e. gradingECO ______________________________ for most economic performance at
best environmental conditionsPOWER__________________________ for max. output
Super-Finish ________________________ additional operator adjustable workspeed function for further increasedfeathering. Applies to all modes andall control functions
R.P.M. adjustment ________________ stepless adjustment of engine outputvia the r.p.m. at each selected mode
Optional add on circuits ________ four preadjustable pump flows fortools
Hydraulic ControlsPower distribution ________________via control valve with integrated
safety valves, simultaneous andindependent operation of traveldrive, swing drive and allattachment functions
Control typeAttachment and swing____ proportional via joystick leversTravel ____________________________ proportional via foot pedal
Additional functions______________via switch and/or proportional footpedals
UndercarriageDrive______________________________variable flow swashplate motor with
automatic brake valveTransmission__________________ oversized two speed power shift
transmission with additional creeperspeed
Travel speed____________________ 0 1.6 mph (creeper speed off road)0 3.1 mph (off road)0 5.6 mph (creeper speed on road)0 12.4 mph (road travel)0 18.6 mph Speeder (Option)
Drawbar pull, max.__________ 100 kNAxles______________________________ 88200 lb excavator axles; automatic or
operator controlled front axle oscillationlock
Brakes____________________________wet, maintenance-free multi disc brakes,opt: rigid axle with drum brakes. Springapplied/pressure released parking brakeintegrated into gear box
Stabilization____________________ 2-point outriggers, rear;stabilizing blade (adjustable during travelfor dozing) rear;stabilizing blade (front) + 2 pt. outriggers,rear;4 point outriggers
AttachmentType ______________________________ combination of high yield steel plates
and cast steel componentsHydraulic cylinders ________ Liebherr cylinders with special seal
system. Shock absorptionPivots ____________________________ sealed, low maintenanceLubrication ____________________ centralized in easily accessible locationsHydraulic connections ____ pipes and hoses equipped with SAE
split-flange connectionsBucket____________________________ standard equipped with 26500 lb
safety hook for lifting
Operator CabCab ________________________________built from deep drawn components,
resiliently mounted, sound insulated,tinted windows, front window storesoverhead, door with sliding window
Operator's seat________________ fully adjustable, shockabsorbingsuspension, adjustable to operator's
weight and size, 6-way adjustableLiebherr seat
Joysticks ________________________ integrated into adjustable consolesMonitoring______________________ menu driven query of current operating
conditions via the LCD display.Automatic monitoring, display, warning(acoustical and optical signal) and saving
machine data, for example,engine overheating, low engine oilpressure or low hydraulic oil level
Heater/airconditioner______ combined hotwater heater/airconditionerwith dust filter for fresh or circulatedairflow
Noise emission________________ L pA ( inside cab) = 77 dB(A)(86/662/EEC) L wA (surround noise) = 102 dB(A)
Swing DriveDrive______________________________ Liebherr swashplate motor with torque
control and integrated brake valveTransmission__________________ Liebherr compact planetary reduction
gearSwing ring______________________ Liebherr sealed single race ball bearing
swing ring, internal teethSwing speed____________________ 09.0 R.P.M.Swing torque __________________ 46 kNmHolding brake ________________wet discs (spring applied pressure
released)Option____________________________ pedal controlled positioning brake
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
3/14
Dimensions
3
B
T
E
X
D
C
A
Q
W
K
H
M
L
U
Z
V
N
Z
M N
L
U
K
JI
B
S
Q
J
B
S
T
Q
L
U
P M N
I
K
Z
M N
L
U
Z
K
B
T
Q
Tires 10.00-20
A 904 A 904 A 904 A 904 A 904 EW A 904 EWwith with with with with withstabilizing 2 pt. stabilizing 4 pt. stabilizing 2 pt.blade out- blade and out- blade out-
riggers 2 pt. outr. riggers riggersft-in ft-in ft-in ft-in ft-in ft-in
A 82 82 8 2 8 2 82 8 2B 81 81 8 1 8 1 88 8 8C 103 103 10 3 10 3 103 10 3D 78 78 7 8 7 8 78 7 8E 80 80 8 0 8 0 80 8 0H 79 79 7 9 7 9 79 7 9I 18 1 7 18
J 21 2 0 21 K 40 40 4 0 4 0 40 4 0L 86 86 8 6 8 6 86 8 6M 37 37 3 7 3 7 37 3 7N 42 35 3 5 3 5 42 3 5P 5 0 Q 12 12 1 2 1 2 12 1 2S 82 8 2 90 T 121 12 1 12 1 12 1U 151 144 1611 1510 151 14 4Z 149 149 1710 14 9 149 1710Z* 149 149 14 8 14 9 149 14 8
E = tail radius
Stick with hydr. adjustable boom with gooseneck boomand and and 4 pt. and and and 4 pt.stabiliz- 2 pt. outr. or stabiliz- 2 pt. outr. or ing outr. blade + 2 pt. ing outr. blade + 2 pt.blade outr. blade outr.
ft-in ft-in ft-in ft-in ft-in ft-in ft-in
V 5 7 22 0 215 21 5 22 2 21 7 21 77 2 1910 193 19 3 19 5 1810 1810710 18 2 181 19 3* 18 6 18 8 19 7*810 18 1 173 20 3* 18 3 17 8 20 5*
10 6 19 0 185 21 2* 19 0 18 5 21 2*
W 5 7 10 2 102 10 2 10 8 10 8 10 8
7 2 10 2 102 10 2 10 4 10 4 10 4710 10 2 102 10 2* 10 6 10 6 10 6*810 10 2 102 10 2* 1010 1010 1010*
10 6 11 7 117 11 7* 1111 1111 1111*
X 5 7 29 2 287 28 7 29 3 28 9 28 97 2 2811 285 28 5 29 2 28 7 28 7710 2811 285 29 6* 29 2 28 7 2910*810 2811 285 31 3* 29 3 28 9 31 5*
10 6 28 7 282 3011* 2811 28 5 31 1*
Dimensions are with attachment over steering axle*Attachment over digging axle for shorter transportdimensions
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
4/144
Backhoe Attachmentwith Hydr. Adjustable Boom
11
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
m
0 ft51015202530
0 m12345678910
10
30
25
20
15
10
5
0
-5
-10
-15
-20
ft
35
1
234
5
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 57 7 2 710 810 10 6
Max. digging depth ft-in 168 18 0 19 0 19 8 19 7Max. reach at groundlevel ft-in 268 28 2 2810 2910 31 5Max. dumping height ft-in 212 22 3 22 7 23 3 24 3
Max. teeth height ft-in 296 3010 31 2 31 9 3211
Max. digging force kN 120.3 93.6 87.9 81.3 72.0lb 26900 20950 19624 18300 16100
Max. breakout force kN 126.4 126.4 126.4 126.4 126.4lb 28440 28440 28440 28440 28440
Max. breakout force with ripper bucket: 146 kN (32850 lb)
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 710 stickand the 0.92 cuyd bucket.
Undercarriage versions lb
A 904 litronicwith stabilizing blade 41950A 904 litronicwith 2 pt. outriggers 42940A 904 litronicwith stabilizing blade + 2 pt. outr. 45060A 904 litronicwith 4 pt. outriggers 45470A 904 EW litronicwith stabilizing blade 42260A 904 EW litronicwith 2 pt. outriggers 43160
BucketsCutting width SAE in 91) 132) 152) 203) 22 244) 26 33 41 49 55
Capacity SAE (heaped) cuyd 0.18 0.26 0.33 0.52 0.37 0.46 0.52 0.72 0.92 1.11 1.37Max. material weight lb/cuyd 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Weight withLiebherr teeth Z 13 C lb 970 1040 1190 1380 1570 1680
Weight withLiebherr teeth Z 16 P lb 1540
Weight withBofors teeth lb 750 820 840 900
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 106 106 106 106 106 106 72
Stabilizing blade down ft-in 106 106 106 106 106 106 106 106 810 57
2 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 810 72
Stabilizing blade + 2 pt. outr. down ft-in 106 106 106 106 106 106 106 106 106 106 106
4 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 106 106
EW, stabilizers raised ft-in 106 106 106 106 106 106 106 106 810 57 EW, Stabilizing blade down ft-in 106 106 106 106 106 106 106 106 106 72 57
EW, 2 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 106 72
1) Bucket with ejector (max. digging depth 307, since bucket suspension is wider than bucket)2) Bucket with ejector (max. digging depth 311, since bucket suspension is wider than bucket)3) Bucket with ejector4) Ripper bucket
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
5/14
Lift capacities A 904 litronicwith Hydr. Adjustable Boom
5
Lift capacities are stated in 1000 lb and can be lifted 360h on firm, level supporting surface. Loads in ( . . . ) can be lifted over end only. Capacities shown forStabilizers raised are valid only over the front or steering axle (travel position). Indicated loads are based on ISO 10567 and do not exceed 75 % of tipping or87% of hydraulic capacity. Indicated loads are limited by the weld-on safety hook to 26500 lb. Without bucket (0.92 cuyd) lift capacities increase by 1370 lb,and without bucket cylinder, link and lever they increase by an additional 640 lb.
+ Rating limited by hoist cylindersh Rating limited by stick cylinder
Note: When used within the countries of the European Union and when lifting a load, this excavator has to be equipped with an overload warning device and itshoist cylinders with automatic check valves, according to the European Standard EN 474-5.
with stick 72Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down
2 pt. outr. downBlade + 2 pt. down104 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. downStabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
9.1 (10.5+) 5.8 ( 7.1h )9.8 (10.5+) 6.3 ( 7.1h )
10.5+ (10.5+) 7.1h ( 7.1h )10.5+ (10.5+) 7.1h ( 7.1h )10.5+ (10.5+) 7.1h ( 7.1h )
16.4 (16.9+) 8 .9 (11.7+) 5.7 ( 8.8 ) 3 .3 (6.0 )16.6 (16.9+) 9 .5 (11.7+) 6 .1 (10.4+) 3.6 (6.9h )16.9+ (16.9+) 11.1 (11.7+) 7 .1 (10.4+) 4.7 (6.9h )16.9+ (16.9+) 11.7+ (11.7+) 9 .4 (10.4+) 6 .6 (6.9h )16.9+ (16.9+) 11.7+ (11.7+) 10.4+ (10.4+) 6.9h (6.9h )
14.9 (16.1+) 8.6 (12.8 ) 5.6 ( 8.6+) 3.2 (6.0 )15.9 (16.1+) 9 .3 (14.1+) 6 .0 (11.3+) 3.5 (7.5h )
16.1+ (16.1+) 10.7 (14.1+) 7 .2 (11.3+) 4.7 (7.5h )16.1+ (16.1+) 13.9 (14.1+) 9 .3 (11.3+) 6.6 (7.5h )16.1+ (16.1+) 14.1+ (14.1+) 10.3 (11.3+) 7.5h (7.5h )
15.6 (20.3+) 8 .5 (12.7+) 5.4 ( 8.4 ) 3 .2 (5 .9 )15.8 (20.3+) 9 .1 (17.0+) 5 .8 (12.5+) 3.5 (7.8h )18.9 (20.3+) 10.5 (17.0+) 7 .3 (12.5+) 4.6 (7.8h )20.3+ (20.3+) 13.8 (17.0+) 9 .2 (12.5+) 6.5 (7.8h )20.3+ (20.3+) 15.4 (17.0+) 10.2 (12.5+) 7.4 (7.8h )
15.1 (25.1 ) 8.1 (13.4+) 4.8 ( 8.4 ) 2 .8 (5 .5 )16.4 (26.9+) 8 .8 (18.3+) 5 .2 (13.2+) 3.2 (9.0h )19.9 (26.9+) 11.0 (18.3+) 6 .6 (13.1 ) 4 .2 (9.0h )26.9+ (26.9+) 14.3 (18.3+) 9 .1 (13.2+) 6.1 (9.0h )26.9+ (26.9+) 15.9 (18.3+) 10.4 (13.2+) 7.0 (9.0h )
14.0 (26.2+) 7.8 (13.6 ) 4.6 ( 8.4 )15.3 (29.5+) 8 .4 (18.6+) 5 .0 (14.0h )19.9 (29.5+) 10.6 (18.6+) 6 .5 (14.0h )27.9 (29.5+) 14.8 (18.6+) 9 .2 (14.0h )29.5+ (29.5+) 16.9 (18.6+) 10.5 (14.0h )
14.0 (26.9 ) 6 .7 (12.4 ) 4 .0 ( 7.7 )15.2 (31.0+) 7 .3 (18.3+) 4 .4 (10.6+)19.9 (31.0+) 9 .5 (18.3+) 5 .9 (10.6+)29.3 (31.0+) 13.6 (18.3+) 8 .4 (10.6+)
31.0+ (31.0+) 15.6 (18.3+) 9 .6 (10.6+)12.9 (20.0+) 6.9 ( 9.7+)14.2 (20.0+) 7.6 ( 9.7+)18.7 (20.0+) 9.7+ ( 9.7+)20.0+ (20.0+) 9.7+ ( 9.7+)20.0+ (20.0+) 9.7+ ( 9.7+)
with stick 710Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down
2 pt. outr. downBlade + 2 pt. down104 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. downStabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
9.7 (10.2+) 6.1 ( 8.7+) 3.9 ( 6.1h )10.2+ (10.2+) 6 .6 ( 8.7+) 4.2 ( 6.1h )10.2+ (10.2+) 7 .8 ( 8.7+) 5.4 ( 6.1h )10.2+ (10.2+) 8.7+ ( 8.7+) 6.1h ( 6.1h )10.2+ (10.2+) 8.7+ ( 8.7+) 6.1h ( 6.1h )
16.0 (16.5+) 8 .9 (10.9+) 6.0 ( 9.2 ) 3.6 ( 6.2 )16.5+ (16.5+) 9 .6 (10.9+) 6.4 ( 9.4+) 4.0 ( 7.5h )16.5+ (16.5+) 10.9+ (10.9+) 7 .5 ( 9.4+) 5.1 ( 7.5h )16.5+ (16.5+) 10.9+ (10.9+) 9.4+ ( 9.4+) 6.8 ( 7.5h )16.5+ (16.5+) 10.9+ (10.9+) 9.4+ ( 9.4+) 7.5h ( 7.5h )
15.3 (20.5h ) 8.6 (13 .3 ) 5.9 ( 8.8 ) 3.7 ( 6.6h )16.0 (20.5h ) 9 .3 (13.7+) 6 .3 (10.6+) 4.1 ( 9.1+)
20.5h (20.5h ) 10.7 (13.7+) 7 .2 (10.6+) 5.2 ( 9.1+)20.5h (20.5h ) 13.7+ (13.7+) 9 .6 (10.6+) 6.6 ( 9.1+)20.5h (20.5h ) 13.7+ (13.7+) 10.6+ (10.6+) 7.5 ( 9.1+)
16.4 (18.1h ) 8.5 (13.3 ) 5.7 ( 8.8 ) 3.6 ( 6.6 )16.4 (18.1h ) 9 .2 (16.5+) 6 .1 (11.8+) 4.0 ( 9.6+)18.1h (18.1h ) 10.7 (16.5+) 7 .1 (11.8+) 5.2 ( 9.6+)18.1h (18.1h ) 14.1 (16.5+) 9 .3 (11.8+) 7.1 ( 9.6+)18.1h (18.1h ) 15.8 (16.5+) 10.4 (11.8+) 7.5 ( 9.6+)
15.1 (23.6+) 8.6 (13.9 ) 5.6 ( 9.2 ) 3 .2 ( 6.0 )16.2 (23.6+) 9 .3 (17.8+) 6 .1 (12.7+) 3.5 ( 9.9+)20.0 (23.6+) 11.3 (17.8+) 7 .6 (12.7+) 4 .6 ( 9.8 )23.6+ (23.6+) 14.7 (17.8+) 9 .6 (12.7+) 6.6 ( 9.9+)23.6+ (23.6+) 16.4 (17.8+) 10.7 (12.7+) 7.6 ( 9.9+)
14.8 (26.6 ) 8.1 (14.3+) 5.3 ( 9.4 ) 3 .0 ( 5.9 )16.1 (27.8+) 8 .8 (18.0+) 5 .8 (13.0+) 3.3 ( 9.7h )21.0 (27.8+) 11.1 (18.0+) 7 .4 (13.0+) 4.5 ( 9.7h )27.8+ (27.8+) 15.0 (18.0+) 10.3 (13.0+) 6.5 ( 9.7h )27.8+ (27.8+) 16.8 (18.0+) 11.7 (13.0+) 7.4 ( 9.7h )
14.5 (28.0 ) 8 .7 (15.7 ) 4 .3 ( 8 .2 )15.8 (29.6+) 9 .5 (19.8+) 4 .8 (12.8+)20.7 (29.6+) 12.1 (19.8+) 6 .3 (12.8+)29.6+ (29.6+) 17.0 (19.8+) 8 .9 (12.8+)
29.6+ (29.6+) 19.5 (19.8+) 10.2 (12.8+)14.0 (27.6 ) 7.3 (13.7 )15.4 (28.0+) 8 .0 (15.6+)20.3 (28.0+) 10.4 (15.6+)28.0+ (28.0+) 14.9 (15.6+)28.0+ (28.0+) 15.6+ (15.6+)
with stick 810Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. down
Blade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.6 ( 9.0+) 3 .4 ( 5.3h )6.0 ( 9.0+) 3 .8 ( 5.3h )7.3 ( 9.0+) 4 .8 ( 5.3h )9.0+ ( 9.0+) 5.3h ( 5.3h )9.0+ ( 9.0+) 5.3h ( 5.3h )
16.2 (16.7+) 8 .7 (10.3+) 5.5 ( 8.7 ) 3 .2 ( 5.3h )16.7+ (16.7+) 9 .3 (10.3+) 5.9 ( 9.4+) 3 .5 ( 5.3h )16.7+ (16.7+) 10.3+ (10.3+) 7.2 ( 9.4+) 4 .5 ( 5.3h )
16.7+
(16.7+
) 10.3+
(10.3+
) 9.4+
( 9.4+
) 5.3h
( 5.3h
)16.7+ (16.7+) 10.3+ (10.3+) 9.4+ ( 9.4+) 5.3h ( 5.3h )
15.5 (16.4h ) 8 .3 (12.9+) 5.4 ( 8.5+) 3.2 ( 5.6 )16.0 (16.4h ) 9 .0 (12.9+) 5 .9 (10.6+) 3 .5 ( 8.8h )16.4h (16.4h ) 10.4 (12.9+) 7 .0 (10.6+) 4 .6 ( 8.8h )16.4h (16.4h ) 12.9+ (12.9+) 9 .1 (10.6+) 6 .2 ( 8.8h )16.4h (16.4h ) 12.9+ (12.9+) 10.1 (10.6+) 6 .9 ( 8.8h )
15.1 (20.2+) 8.1 (12.6 ) 5.5 ( 8.3+) 3.1 ( 5.8 )15.5 (20.2+) 8 .8 (15.9+) 5 .9 (11.9+) 3.4 ( 9.4 )18.3 (20.2+) 10.2 (15.9+) 6 .9 (11.9+) 4.4 ( 9.0 )20.2+ (20.2+) 13.5 (15.9+) 9 .0 (11.9+) 5.9 ( 9 .8+)20.2+ (20.2+) 15.1 (15.9+) 10.0 (11.9+) 6.8 ( 9 .8+)
15.1 (24.5+) 8.2 (13.2 ) 5.6 ( 8.4h ) 2.7 ( 5.3 )15.6 (24.5+) 8 .9 (17.9+) 6 .0 (12.9+) 3 .0 ( 9 .3 )19.3 (24.5+) 10.7 (17.9+) 7 .5 (12.9+) 4 .0 ( 8 .9 )24.5+ (24.5+) 14.0 (17.9+) 9 .0 (12.9+) 5.9 (10.0+)24.5+ (24.5+) 15.6 (17.9+) 10.3 (12.9+) 6.7 (10.0+)
14.0 (25.6+) 7.6 (13.4 ) 4.5 ( 8.1 ) 2.6 ( 5.3 )15.3 (28.7+) 8 .3 (18.2+) 4 .9 (13.2+) 2 .9 ( 8.0h )20.0 (28.7+) 10.5 (18.2+) 6 .3 (13.2+) 4 .0 ( 8.0h )27.6 (28.7+) 14.6 (18.2+) 8 .9 (13.2+) 5 .8 ( 8.0h )28.7+ (28.7+) 16.1 (18.2+) 10.0 (13.2+) 6 .7 ( 8.0h )
13.7 (26.4 ) 7 .4 (13.5 ) 4 .3 ( 8.1 )14.9 (30.0+) 8 .1 (19.7+) 4 .7 (13.5+)19.5 (30.0+) 10.4 (19.7+) 6 .2 (13.5+)28.9 (30.0+) 14.8 (19.7+) 8 .9 (13.5+)30.0+ (30.0+) 17.0 (19.7+) 10.2 (13.5+)
15.3 (30.8+) 6 .4 (12.1 )16.9 (30.8+) 7 .1 (12.8+)22.5 (30.8+) 9 .2 (12.8+)30.8+ (30.8+) 12.8+ (12.8+)30.8+ (30.8+) 12.8+ (12.8+)
with stick 106Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. down
Blade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.8 ( 7.9+) 3 .5 (4.2h )6.2 ( 7.9+) 3 .8 (4.2h )7.5 ( 7.9+) 4.2h (4.2h )7.9+ ( 7.9+) 4.2h (4.2h )7.9+ ( 7.9+) 4.2h (4.2h )
8.8 (10.1+) 5.5 ( 8.4+) 3.6 (5.8 )9.4 (10.1+) 5.9 ( 8.4+) 3 .9 (6.7h )
10.1+ (10.1+) 7 .2 ( 8.4+) 4 .6 (6.7h )
10.1+
(10.1+
) 8.4+
( 8.4+
) 6 .4 (6.7h
)10.1+ (10.1+) 8.4+ ( 8.4+) 6.7h (6.7h )
15.6 (16.5+) 8 .2 (11.6+) 5.4 ( 8.5 ) 3.2 (5.7 )15.8 (16.5+) 8 .8 (11.6+) 5.9 ( 9.8+) 3.5 (8.6+)16.5+ (16.5+) 10.3 (11.6+) 6.8 ( 9.8+) 4.4 (8.6+)16.5+ (16.5+) 11.6+ (11.6+) 9 .0 ( 9.8+) 6.2 (8.6+)16.5+ (16.5+) 11.6+ (11.6+) 9.8+ ( 9.8+) 7 .1 (8.6+)
14.8 (19.2h ) 8.3 (12.6 ) 5 .3 ( 8.3+) 3.1 (5.5 )15.4 (19.2h ) 8 .9 (14.9+) 5 .8 (11.2+) 3.4 (9.3+)18.1 (19.2h ) 10.0 (14.9+) 6 .8 (11.2+) 4.4 (9.0 )19.2h (19.2h ) 13.3 (14.9+) 8 .8 (11.2+) 6.0 (9.3+)19.2h (19.2h ) 14.9+ (14.9+) 9 .8 (11.2+) 6.9 (9.3+)
14.7 (24.5h ) 8.3 (12.9 ) 5.2 ( 8.6 ) 3 .1 (5.5h )15.3 (24.5h ) 8 .9 (17.2+) 5 .6 (12.5+) 3.4 (9.4 )19.0 (24.5h ) 10.4 (17.2+) 7 .0 (12.5+) 4.4 (9.1 )24.5h (24.5h ) 13.7 (17.2+) 9 .1 (12.5+) 5.9 (9.8+)24.5h (24.5h ) 15.3 (17.2+) 10.1 (12.5+) 6.8 (9.8+)
14.1 (25.3 ) 7.6 (13.2+) 4.6 ( 8.2h ) 2.8 (5.6 )15.4 (27.7+) 8 .3 (18.0+) 5 .0 (12.9+) 3.2 (9.1 )20.1 (27.7+) 10.5 (18.0+) 6.4 (12.9 ) 4.3 (8.8 )27.0 (27.7+) 14.2 (18.0+) 8 .7 (12.9+) 6 .2 (9.1h )27.7+ (27.7+) 15.8 (18.0+) 9 .9 (12.9+) 7 .1 (9.1h )
13.6 (26.3 ) 7 .3 (13.2 ) 4 .1 ( 7 .7 )14.8 (29.4+) 8 .0 (18.4+) 4 .5 (12.1+)19.4 (29.4+) 10.2 (18.4+) 5 .9 (12.1+)27.9 (29.4+) 14.3 (18.4+) 8 .4 (12.1+)29.4+ (29.4+) 15.9 (18.4+) 9 .6 (12.1+)
13.7 (27.2 ) 6 .7 (12.5 ) 3 .9 ( 7 .6 )15.1 (30.9+) 7 .3 (17.8+) 4.3 ( 9.0+)19.9 (30.9+) 9 .5 (17.8+) 5.8 ( 9.0+)29.8 (30.9+) 13.7 (17.8+) 8.4 ( 9.0+)30.9+ (30.9+) 15.8 (17.8+) 9.0+ ( 9.0+)
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
6/146
Lift capacities A 904 EW litronicwith Hydr. Adjustable Boom
Lift capacities are stated in 1000 lb and can be lifted 360h on firm, level supporting surface. Loads in ( . . . ) can be lifted over end only. Capacities shown forStabilizers raised are valid only over the front or steering axle (travel position). Indicated loads are based on ISO 10567 and do not exceed 75 % of tipping or87% of hydraulic capacity. Indicated loads are limited by the weld-on safety hook to 26500 lb. Without bucket (0.92 cuyd) lift capacities increase by 1370 lb,and without bucket cylinder, link and lever they increase by an additional 640 lb.
+ Rating limited by hoist cylindersh Rating limited by stick cylinder
Note: When used within the countries of the European Union and when lifting a load, this excavator has to be equipped with an overload warning device and itshoist cylinders with automatic check valves, according to the European Standard EN 474-5.
with stick 72Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
9.1h ( 9.1h ) 6 .5 ( 7 .2h )9.1h ( 9.1h ) 7 .0 ( 7 .2h )9.1h ( 9.1h ) 7.2h ( 7.2h )
10.1 (10.5+) 6 .5 ( 7 .1h )10.5+ (10.5+) 6 .8 ( 7 .1h )10.5+ (10.5+) 7.1h ( 7.1h )
16.9+ (16.9+) 9 .9 (11.7+) 6.4 ( 8.8 ) 3.8 (6.0 )16.9+ (16.9+) 10.2 (11.7+) 6.8 (10.4+) 4.2 (6.9h )16.9+ (16.9+) 11.7+ (11.7+) 7.6 (10.4+) 5.0 (6.9h )
16.0 (16.1+) 9 .6 (12.8 ) 6 .3 ( 8 .6+) 3.7 (6.0 )16.1+ (16.1+) 9 .9 (14.1+) 6.8 (11.3+) 4.1 (7.5h )16.1+ (16.1+) 11.1 (14.1+) 7.6 (11.3+) 5.0 (7.5h )
15.8 (20.3+) 9 .5 (12.7+) 6.1 ( 8.5 ) 3.7 (6.0 )16.7 (20.3+) 9 .8 (17.0+) 6.7 (12.5+) 4.1 (7.8h )20.3+ (20.3+) 10.8 (17.0+) 7.8 (12.5+) 4.9 (7.8h )
17.1 (25.2 ) 9.1 (13.4+) 5.4 ( 8.4 ) 3.3 (5.6 )17.7 (26.9+) 10.0 (18.3+) 5.9 (13.2+) 3.7 (9.0h )21.3 (26.9+) 11.7 (18.3+) 7 .1 (13.2 ) 4 .6 (9.0h )
16.0 (26.2+) 8 .8 (13.7 ) 5 .3 ( 8 .5 )17.7 (29.5+) 9 .6 (18.6+) 5 .8 (14.0h )21.6 (29.5+) 11.4 (18.6+) 7 .0 (14.0h )
16.0 (27.0 ) 7.7 (12.5 ) 4.7 ( 7.7 )17.7 (31.0+) 8 .5 (18.3+) 5.2 (10.6+)
21.5 (31.0+) 10.3 (18.3+) 6.3 (10.6+)
14.9 (20.0+) 7.9 ( 9.7+)16.6 (20.0+) 8.8 ( 9.7+)20.0+ (20.0+) 9.7+ ( 9.7+)
with stick 710Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
6.7 ( 6.8h )6.8h ( 6.8h )6.8h ( 6.8h )
10.2+ (10.2+) 6 .8 ( 8 .7+) 4.4 ( 6.1h )10.2+ (10.2+) 7 .2 ( 8 .7+) 4.8 ( 6.1h )10.2+ (10.2+) 8 .3 ( 8 .7+) 5.8 ( 6.1h )
16.5+ (16.5+) 9 .9 (10.9+) 6.6 ( 9.2 ) 4 .2 ( 6.2 )16.5+ (16.5+) 10.5 (10.9+) 6 .9 ( 9 .4+) 4.6 ( 7.5h )16.5+ (16.5+) 10.9+ (10.9+) 8 .0 ( 9 .4+) 5.5 ( 7.5h )
16.8 (20.5h ) 9.4 (13 .4 ) 6.5 ( 8.9 ) 4.3 ( 6.6h )18.6 (20.5h ) 9 .6 (13.7+) 6.7 (10.6+) 4.7 ( 9.1+)20.5h (20.5h ) 11.5 (13.7+) 7.6 (10.6+) 5.6 ( 9.1+)
16.4 (18.1h ) 9.3 (13 .4 ) 6.4 ( 8.8 ) 4 .2 ( 6.6 )17.3 (18.1h ) 9 .6 (16.5+) 6.7 (11.8+) 4.6 ( 9.6+)18.1h (18.1h ) 11.5 (16.5+) 7.6 (11.8+) 5.5 ( 9.6+)
17.0 (23.6+) 9 .3 (13.9+) 6.3 ( 9.2 ) 3 .7 ( 6.1 )18.8 (23.6+) 10.2 (17.8+) 6.9 (12.7+) 4.1 ( 9.9+)21.7 (23.6+) 11.6 (17.8+) 8.1 (12.7+) 5.0 ( 9.9+)
16.9 (26.7 ) 9 .2 (14.3 ) 6 .1 ( 9.5 ) 3 .5 ( 5.9 )18.7 (27.8+) 10.1 (18.0+) 6.7 (13.0+) 4.0 ( 9.7h )22.8 (27.8+) 11.9 (18.0+) 7.9 (13.0+) 4.9 ( 9.7h )
16.6 (28.1 ) 9.9 (15.7 ) 5.0 ( 8.2 )18.4 (29.6+) 10.9 (19.8+) 5.6 (12.8+)
22.4 (29.6+) 13.0 (19.8+) 6.8 (12.8+)
16.2 (27.8 ) 8.4 (13.7 )18.0 (28.0+) 9 .3 (15.6+)22.0 (28.0+) 11.3 (15.6+)
with stick 810Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
5.8h ( 5.8h )5.8h ( 5.8h )5.8h ( 5.8h )
6.3 ( 9.0+) 3.9 (5 .3h )6.8 ( 9.0+) 4.3 (5 .3h )7.8 ( 9.0+) 5.2 (5 .3h )
16.7+ (16.7+) 9 .7 (10.3+) 6.2 ( 8.8 ) 3.7 (5 .3h )16.7+ (16.7+) 10.3+ (10.3+) 6 .7 ( 9 .4+) 4.0 (5 .3h )16.7+ (16.7+) 10.3+ (10.3+) 7 .5 ( 9 .4+) 4.9 (5 .3h )
16.0 (16.4h ) 9 .3 (12.9+) 6 .1 ( 8.5+) 3.7 (5.6 )16.4h (16.4h ) 9 .8 (12.9+) 6.6 (10.6+) 4 .1 (8 .8h )16.4h (16.4h ) 11.1 (12.9+) 7.4 (10.6+) 4 .9 (8 .8h )
15.5 (20.2+) 9 .1 (12.7 ) 6 .1 ( 8 .3+) 3.6 (5.8 )16.9 (20.2+) 9 .6 (15.9+) 6.2 (11.9+) 4.0 (9.5 )19.9 (20.2+) 10.9 (15.9+) 7.2 (11.9+) 4.8 (9.1 )
16.3 (24.5+) 9.2 (13.3 ) 6 .3 ( 8.4h ) 3.2 (5.3 )18.0 (24.5+) 9 .6 (17.9+) 6.8 (12.9+) 3.6 (9.4 )20.9 (24.5+) 11.4 (17.9+) 7.7 (12.9+) 4.4 (9.0 )
16.1 (25.6+) 8.6 (13.5 ) 5.1 ( 8.2 ) 3.1 (5.3 )17.8 (28.7+) 9 .4 (18.2+) 5.7 (13.2+) 3 .5 (8.0h )21.6 (28.7+) 11.2 (18.2+) 6.8 (13.2+) 4 .3 (8.0h )
15.7 (26.6 ) 8.5 (13.6 ) 5.0 ( 8.1 )17.4 (30.0+) 9 .4 (19.7+) 5.5 (13.5+)21.2 (30.0+) 11.2 (19.7+) 6.7 (13.5+)
17.8 (30.8+) 7 .4 (12.2 )19.9 (30.8+) 8 .2 (12.8+)24.6 (30.8+) 10.0 (12.8+)
with stick 106Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
5.5h ( 5.5h )5.5h ( 5.5h )5.5h ( 5.5h )
6.5 ( 7.9+) 3.9 (4.2h )6.9 ( 7.9+) 4.2 (4.2h )7.9+ ( 7.9+) 4.2h (4.2 h )
9.8 (10.1+) 6.1 ( 8.4+) 4.1 (5.8 )10.1+ (10.1+) 6.7 ( 8.4+) 4.2 (6.7h )10.1+ (10.1+) 7.5 ( 8.4+) 4.9 (6.7h )
16.1 (16.5+) 9.2 (11.6+) 6.1 ( 8.5 ) 3.7 (5.8 )16.5+ (16.5+) 9.8 (11.6+) 6.5 ( 9.8+) 4.1 (8.6+)16.5+ (16.5+) 11.0 (11.6+) 7.3 ( 9.8+) 4.8 (8.6+)
15.5 (19.2h ) 9.3 (12.6 ) 6.0 ( 8.3+) 3.5 (5.5 )16.8 (19.2h ) 9.4 (14.9+) 6.5 (11.2+) 3.9 (9.3+)19.2h (19.2h ) 10.7 (14.9+) 7.0 (11.2+) 4.8 (9.1 )
15.9 (24.5h ) 9.3 (12.9 ) 5.8 ( 8.6 ) 3.6 (5.5h )17.6 (24.5h ) 9.6 (17.2+) 6.3 (12.5+) 4.0 (9.5 )20.6 (24.5h ) 11.2 (17.2+) 7.5 (12.5+) 4.8 (9.1 )
16.2 (25.4 ) 8.6 (13.2+) 5.3 ( 8.2h ) 3.4 (5.6 )17.9 (27.7+) 9.5 (18.0+) 5.8 (12.9+) 3.8 (9.1h )21.0 (27.7+) 11.3 (18.0+) 6.9 (12.9+) 4.6 (8.9 )
15.6 (26.5 ) 8.4 (13.2 ) 4.7 ( 7.7 )17.3 (29.4+) 9.2 (18.4+) 5.2 (12.1+)21.1 (29.4+) 11.0 (18.4+) 6.3 (12.1+)
15.8 (27.4 ) 7.7 (12.6 ) 4.6 ( 7.7 )17.6 (30.9+) 8.5 (17.8+) 5.1 ( 9.0+)21.6 (30.9+) 10.3 (17.8+) 6.3 ( 9.0+)
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
7/14
Backhoe Attachmentwith Gooseneck Boom 171
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 5 7 7 2 710 810 10 6
Max. digging depth ft-in 17 2 1810 19 4 20 6 22 2Max. reach at groundlevel ft-in 2610 28 4 29 0 30 0 31 7Max. dumping height ft-in 19 4 19 8 21 2 21 2 2111
Max. teeth height ft-in 27 8 28 6 29 6 29 6 30 4
Max. digging force kN 120.3 93.6 87.9 81.3 72.0lb 26900 20950 19624 18300 16100
Max. breakout force kN 126.4 126.4 126.4 126.4 126.4lb 28440 28440 28440 28440 28440
Max. breakout force with ripper bucket: 146 kN (32850 lb)
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 710 stickand the 0.92 cuyd bucket.
Undercarriage versions lb
A 904 litronicwith stabilizing blade 37390A 904 litronicwith 2 pt. outriggers 38390A 904 litronicwith stabilizing blade + 2 pt. outr. 40500A 904 litronicwith 4 pt. outriggers 40920A 904 EW litronicwith stabilizing blade 37700A 904 EW litronicwith 2 pt. outriggers 38610
BucketsCutting width SAE in 91) 132) 152) 203) 22 244) 26 33 41 49 55
Capacity SAE (heaped) cuyd 0.18 0.26 0.33 0.52 0.37 0.46 0.52 0.55 0.92 1.11 1.37Max. material weight lb/cuyd 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Weight withLiebherr teeth Z 10 C lb 970 1040 1190 1380 1570 1680
Weight withLiebherr teeth Z 16 P lb 1540
Weight withBofors teeth lb 750 820 840 900
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 106 106 106 106 106 106 72
Stabilizing blade down ft-in 106 106 106 106 106 106 106 106 72 57
2 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 72 72
Stabilizing blade + 2 pt. outr. down ft-in 106 106 106 106 106 106 106 106 106 106 72
4 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 106 72
EW, stabilizers raised ft-in 106 106 106 106 106 106 106 106 106 57 EW, Stabilizing blade down ft-in 106 106 106 106 106 106 106 106 106 72 57
EW, 2 point outriggers down ft-in 106 106 106 106 106 106 106 106 106 106 72
1) Bucket with ejector (max. digging depth 307, since bucket suspension is wider than bucket)2) Bucket with ejector (max. digging depth 311, since bucket suspension is wider than bucket)3) Bucket with ejector4) Ripper bucket
7
30
25
20
15
10
5
0
-5
-10
-15
-20
ft
10
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
m
0 ft51015202530
0 m12345678910
1
234
5
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
8/14
Lift capacities A 904 litronicwith Gooseneck Boom 171
Lift capacities are stated in 1000 lb and can be lifted 360h on firm, level supporting surface. Loads in ( . . . ) can be lifted over end only. Capacities shown forStabilizers raised are valid only over the front or steering axle (travel position). Indicated loads are based on ISO 10567 and do not exceed 75 % of tipping or87% of hydraulic capacity. Indicated loads are limited by the weld-on safety hook to 26500 lb. Without bucket (0.92 cuyd) lift capacities increase by 1370 lb,and without bucket cylinder, link and lever they increase by an additional 640 lb.
+ Rating limited by hoist cylindersh Rating limited by stick cylinder
Note: When used within the countries of the European Union and when lifting a load, this excavator has to be equipped with an overload warning device and itshoist cylinders with automatic check valves, according to the European Standard EN 474-5.
with stick 72Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down
2 pt. outr. downBlade + 2 pt. down104 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. downStabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.4 ( 6.5h )5.8 ( 6.5h )6.5h ( 6.5h )6.5h ( 6.5h )6.5h ( 6.5h )
15.1 (15.5+) 8 .2 ( 9 .6+) 5.1 ( 8.6 ) 3.4 ( 5.8h )15.5+ (15.5+) 8 .8 ( 9 .6+) 5.5 ( 8.8+) 3.7 ( 5 .8h )15.5+ (15.5+) 9 .6+ ( 9.6+) 6.9 ( 8.8+) 4.8 ( 5 .8h )15.5+ (15.5+) 9 .6+ ( 9.6+) 8.8+ ( 8.8+) 5.8h ( 5.8h )15.5+ (15.5+) 9 .6+ ( 9.6+) 8.8+ ( 8.8+) 5.8h ( 5.8h )
12.7 (13.4h ) 7 .2 (12.4+) 4.7 ( 8.2 ) 3.1 ( 5.6 )13.4h (13.4h ) 7 .8 (12.4+) 5 .1 (10.2+) 3.4 ( 5 .9h )
13.4h (13.4h ) 9 .9 (12.4+) 6 .4 (10.2+) 4.4 ( 5 .9h )13.4h (13.4h ) 12.4+ (12.4+) 8 .9 (10.2+) 5.9h ( 5.9h )13.4h (13.4h ) 12.4+ (12.4+) 10.1 (10.2+) 5.9h ( 5.9h )
10.4h (10.4h ) 6.6 (12.1 ) 4.3 ( 7.8 ) 3.0 ( 5.5 )10.4h (10.4h ) 7 .2 (15.9+) 4 .7 (11.7+) 3.3 ( 7.1h )10.4h (10.4h ) 9 .3 (15.9+) 6 .1 (11.7+) 4.3 ( 7.1h )10.4h (10.4h ) 13.2 (15.9+) 8 .5 (11.7+) 6.1 ( 7.1h )10.4h (10.4h ) 15.2 (15.9+) 9 .7 (11.7+) 6.9 ( 7.1h )
11.7 (13.1h ) 6.5 (11.9 ) 4.2 ( 7.7 ) 3.0 ( 5.6 )12.9 (13.1h ) 7 .1 (18.1+) 4 .6 (13.1+) 3.3 ( 7.5h )13.1h (13.1h ) 9 .2 (18.1+) 6.0 (13.0 ) 4.3 ( 7.5h )13.1h (13.1h ) 13.1 (18.1+) 8 .4 (13.1+) 6.1 ( 7.5h )13.1h (13.1h ) 15.1 (18.1+) 9 .6 (13.1+) 7.0 ( 7.5h )
11.8 (22.1h ) 6.3 (11.7 ) 4.1 ( 7.6 )12.9 (22.1h ) 6 .9 (18.7+) 4 .5 (13.4 )17.2 (22.1h ) 9 .0 (18.7+) 5 .8 (12.9 )22.1h (22.1h ) 12.9 (18.7+) 8 .3 (13.5+)22.1h (22.1h ) 14.8 (18.7+) 9 .5 (13.5+)
12.1 (24.0 ) 6.4 (11.9 ) 4.2 ( 7.7 )13.3 (25.2+) 7 .0 (17.1+) 4 .6 (12.6+)17.6 (25.2+) 9 .1 (17.1+) 6 .0 (12.6+)25.2+ (25.2+) 13.0 (17.1+) 8 .5 (12.6+)
25.2+ (25.2+) 14.9 (17.1+) 9 .6 (12.6+)12.7 (17.4+) 7 .4 (13.3 )13.9 (17.4+) 8 .1 (13.8+)17.4+ (17.4+) 10.3 (13.8+)17.4+ (17.4+) 13.8+ (13.8+)17.4+ (17.4+) 13.8+ (13.8+)
with stick 710Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down
2 pt. outr. downBlade + 2 pt. down104 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. downStabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.5 ( 7.8+)5.9 ( 7.8+)7.3 ( 7.8+)7.8+ ( 7.8+)7.8+ ( 7.8+)
15.5+ (15.5+) 8.2 ( 9.5+) 5 .1 ( 8 .3+) 3.2 ( 5.1h )15.5+ (15.5+) 8.9 ( 9.5+) 5 .5 ( 8 .3+) 3.5 ( 5.1 h )15.5+ (15.5+) 9.5+ ( 9.5+) 6 .9 ( 8 .3+) 4.5 ( 5.1h )15.5+ (15.5+) 9.5+ ( 9.5+) 8.3+ ( 8.3+) 5.1h ( 5.1h )15.5+ (15.5+) 9.5+ ( 9.5+) 8.3+ ( 8.3+) 5.1h ( 5.1h )
12.8 (13.0h ) 7 .3 (11.8+) 4.7 ( 8.2 ) 3 .0 ( 5.6 )13.0h (13.0h ) 7 .8 (11.8+) 5 .1 ( 9 .7+) 3.3 ( 7.1h )
13.0h (13.0h ) 10.0 (11.8+) 6 .4 ( 9 .7+) 4.3 ( 7.1h )13.0h (13.0h ) 11.8+ (11.8+) 8 .9 ( 9 .7+) 6.1 ( 7.1h )13.0h (13.0h ) 11.8+ (11.8+) 9.7+ ( 9.7+) 6.9 ( 7.1h )
10.5h (10.5h ) 6.6 (12 .0 ) 4.3 ( 7.7 ) 2 .9 ( 5.4 )10.5h (10.5h ) 7 .2 (15.5+) 4.7 (11.3+) 3.2 ( 8.9h )10.5h (10.5h ) 9 .3 (15.5+) 6.0 (11.3+) 4.2 ( 8.9h )10.5h (10.5h ) 13.2 (15.5+) 8.5 (11.3+) 5.9 ( 8.9h )10.5h (10.5h ) 15.1 (15.5+) 9.7 (11.3+) 6.8 ( 8.9h )
11.6 (13.2h ) 6.4 (11 .9 ) 4 .2 ( 7.6 ) 2 .8 ( 5.3 )12.8 (13.2h ) 7 .0 (17.8+) 4.6 (12.8+) 3.1 ( 7.2h )13.2h (13.2h ) 9 .1 (17.8+) 5.9 (12.8+) 4.1 ( 7.2h )13.2h (13.2h ) 13.1 (17.8+) 8.4 (12.8+) 5.9 ( 7.2h )13.2h (13.2h ) 15.0 (17.8+) 9.6 (12.8+) 6.7 ( 7.2h )
11.6 (21.5h ) 6.3 (11 .6 ) 4 .0 ( 7.5 )12.8 (21.5h ) 6 .8 (18.7+) 4 .4 (13.3 )17.0 (21.5h ) 8 .9 (18.7+) 5 .8 (12.8 )21.5h (21.5h ) 12.8 (18.7+) 8.2 (13.4+)21.5h (21.5h ) 14.7 (18.7+) 9.4 (13.4+)
11.9 (23.8 ) 6.3 (11.7 ) 4.1 ( 7.5 )13.1 (25.8+) 6 .9 (17.4+) 4.5 (12.3+)17.4 (25.8+) 9 .0 (17.4+) 5.8 (12.3+)25.8+ (25.8+) 12.9 (17.4+) 8.3 (12.3+)
25.8+ (25.8+) 14.8 (17.4+) 9.5 (12.3+)12.6 (19.3+) 6 .8 (12.2 )13.8 (19.3+) 7 .3 (13.5+)18.2 (19.3+) 9 .5 (13.5+)19.3+ (19.3+) 13.4 (13.5+)19.3+ (19.3+) 13.5+ (13.5+)
with stick 810Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. down
Blade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.5 ( 7.0+) 3 .4 ( 4 .3h )5.9 ( 7.0+) 3 .7 ( 4 .3h )7.0+ ( 7.0+) 4.3h ( 4.3h )7.0+ ( 7.0+) 4.3h ( 4.3h )7.0+ ( 7.0+) 4.3h ( 4.3h )
8.4 ( 9.4+) 5.1 ( 7.7+) 3 .2 ( 4 .7h )9.0 ( 9.4+) 5.5 ( 7.7+) 3 .5 ( 4 .7h )9.4+ ( 9.4+) 6.9 ( 7.7+) 4 .5 ( 4 .7h )
9.4+
( 9.4+
) 7.7+
( 7.7+
) 4.7h
( 4.7h
)9.4+ ( 9.4+) 7.7+ ( 7.7+) 4.7h ( 4.7h )
13.3 (15.4+) 7 .4 (11.0+) 4.6 ( 8.2+) 3.0 ( 5.6 )14.5 (15.4+) 8 .0 (11.0+) 5.0 ( 9.2+) 3 .3 ( 8 .5+)15.4+ (15.4+) 10.1+ (11.0+) 6.4 ( 9.2+) 4 .3 ( 8.5+)15.4+ (15.4+) 11.0+ (11.0+) 8.9 ( 9.2+) 6 .1 ( 8.5+)15.4+ (15.4+) 11.0+ (11.0+) 9.2+ ( 9.2+) 7 .0 ( 8 .5+)
11.9 (12.5h ) 6.6 (12.1 ) 4.2 ( 7.7 ) 2.8 ( 5.3 )12.5h (12.5h ) 7 .2 (14.5+) 4 .6 (10.9+) 3.1 ( 9.3 )12.5h (12.5h ) 9 .3 (14.5+) 6 .0 (10.9+) 4.1 ( 9.0 )12.5h (12.5h ) 13.3 (14.5+) 8 .4 (10.9+) 5 .9 ( 9 .3+)12.5h (12.5h ) 14.5+ (14.5+) 9 .6 (10.9+) 6 .8 ( 9 .3+)
11.6 (13.7h ) 6.4 (11.8 ) 4.1 ( 7.6 ) 2.8 ( 5.3 )12.8 (13.7h ) 7 .0 (17.2+) 4 .5 (12.5+) 3.1 ( 9.2 )13.7h (13.7h ) 9 .1 (17.2+) 5 .8 (12.5+) 4.1 ( 8.9 )13.7h (13.7h ) 13.0 (17.2+) 8 .3 (12.5+) 5.8 (10.1+)13.7h (13.7h ) 14.9 (17.2+) 9 .5 (12.5+) 6.7 (10.1+)
11.5 (20.3h ) 6.2 (11.6 ) 3.9 ( 7.4 ) 2.8 ( 5.3 )12.6 (20.3h ) 6 .8 (18.6+) 4 .3 (13.2 ) 3 .1 ( 6.9h )16.9 (20.3h ) 8 .9 (18.6+) 5 .7 (12.7 ) 4 .1 ( 6.9h )20.3h (20.3h ) 12.7 (18.6+) 8 .1 (13.3+) 5 .9 ( 6 .9h )20.3h (20.3h ) 14.7 (18.6+) 9 .3 (13.3+) 6 .8 ( 6 .9h )
11.7 (23.6 ) 6.2 (11.6 ) 4.0 ( 7.4 )12.9 (26.7+) 6 .8 (17.6+) 4 .3 (12.4+)17.2 (26.7+) 8 .9 (17.6+) 5 .7 (12.4+)25.9 (26.7+) 12.7 (17.6+) 8 .1 (12.4+)26.7+ (26.7+) 14.7 (17.6+) 9 .3 (12.4+)
12.2 (20.7+) 6 .5 (12.0 )13.4 (20.7+) 7 .1 (13.8+)17.8 (20.7+) 9 .2 (13.8+)20.7+ (20.7+) 13.2 (13.8+)20.7+ (20.7+) 13.8 (13.8+)
with stick 106Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
20
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. down
Blade + 2 pt. down
15
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
0
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
5
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
10
4 pt. outr. down
Stabilizers raisedStabil. blade down2 pt. outr. downBlade + 2 pt. down
15
4 pt. outr. down
5.6 ( 6.4+) 3.5h ( 3.5h )6.0 ( 6.4+) 3.5h ( 3.5h )6.4+ ( 6.4+) 3.5h ( 3.5h )6.4+ ( 6.4+) 3 .5h ( 3.5h )6.4+ ( 6.4+) 3 .5h ( 3.5h )
5.2 ( 6.6+) 3 .3 ( 5.8 )5.6 ( 6.6+) 3.6 ( 6.8h )6.6+ ( 6.6+) 4 .6 ( 6 .8h )
6.6+
( 6.6+
) 6 .4 ( 6 .8h
)6.6+ ( 6.6+) 6 .8h ( 6.8h )
14.0 (15.2+) 7.5 ( 9.3+) 4 .7 ( 8.1+) 3 .0 ( 5.6 )15.2+ (15.2+) 8.1 ( 9.3+) 5 .1 ( 8.1+) 3 .3 ( 7 .7+)15.2+ (15.2+) 9.3+ ( 9.3+) 6 .5 ( 8.1+) 4 .3 ( 7 .7+)15.2+ (15.2+) 9.3+ ( 9.3+) 8.1+ ( 8.1+) 6 .1 ( 7 .7+)15.2+ (15.2+) 9.3+ ( 9.3+) 8.1+ ( 8.1+) 7 .0 ( 7 .7+)
12.1 (15.0h ) 6.7 (12 .2 ) 4.2 ( 7 .7 ) 2 .8 ( 5.3 )13.3 (15.0h ) 7 .3 (13.4+) 4 .6 (10.2+) 3 .1 ( 8 .7+)15.0h (15.0h ) 9 .4 (13.4+) 6 .0 (10.2+) 4 .1 ( 8 .7+)15.0h (15.0h ) 13.3 (13.4+) 8 .5 (10.2+) 5 .9 ( 8 .7+)15.0h (15.0h ) 13.4+ (13.4+) 9 .7 (10.2+) 6 .7 ( 8 .7+)
11.7 (15.1h ) 6.4 (11 .9 ) 4.1 ( 7 .6 ) 2 .7 ( 5.2 )12.9 (15.1h ) 7 .0 (16.5+) 4 .5 (11.8+) 3 .0 ( 9.2 )15.1h (15.1h ) 9 .1 (16.5+) 5 .8 (11.8+) 4 .0 ( 8.9 )15.1h (15.1h ) 13.0 (16.5+) 8 .3 (11.8+) 5 .8 ( 9 .6+)15.1h (15.1h ) 15.0 (16.5+) 9 .5 (11.8+) 6 .6 ( 9 .6+)
11.4 (18.7h ) 6.1 (11 .5 ) 3.9 ( 7 .3 ) 2 .6 ( 5.1 )12.5 (18.7h ) 6 .7 (18.2+) 4 .3 (13.0+) 2 .9 ( 9.1 )16.8 (18.7h ) 8 .8 (18.2+) 5 .6 (12.6 ) 3 .9 ( 8 .8 )18.7h (18.7h ) 12.7 (18.2+) 8 .1 (13.0+) 5.7 ( 9.4h )18.7h (18.7h ) 14.6 (18.2+) 9 .2 (13.0+) 6.5 ( 9.4h )
11.4 (23.2 ) 6 .0 (11.4 ) 3 .8 ( 7 .3 )12.6 (26.1h ) 6 .6 (18.1+) 4 .2 (12.8+)16.9 (26.1h ) 8 .7 (18.1+) 5 .6 (12.6+)25.5 (26.1h ) 12.6 (18.1+) 8 .0 (12.8+)26.1h (26.1h ) 14.5 (18.1+) 9 .2 (12.8+)
11.9 (22.9+) 6.2 (11 .7 ) 4.1 ( 7 .6 )13.1 (22.9+) 6 .8 (15.5+) 4 .5 (11.5+)17.4 (22.9+) 8 .9 (15.5+) 5 .9 (11.5+)22.9+ (22.9+) 12.8 (15.5+) 8 .4 (11.5+)22.9+ (22.9+) 14.8 (15.5+) 9 .6 (11.5+)
8
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
9/149
Lift capacities A 904 EW litronicwith Gooseneck Boom 171
Lift capacities are stated in 1000 lb and can be lifted 360h on firm, level supporting surface. Loads in ( . . . ) can be lifted over end only. Capacities shown forStabilizers raised are valid only over the front or steering axle (travel position). Indicated loads are based on ISO 10567 and do not exceed 75 % of tipping or87% of hydraulic capacity. Indicated loads are limited by the weld-on safety hook to 26500 lb. Without bucket (0.92 cuyd) lift capacities increase by 1370 lb,and without bucket cylinder, link and lever they increase by an additional 640 lb.
+ Rating limited by hoist cylindersh Rating limited by stick cylinder
Note: When used within the countries of the European Union and when lifting a load, this excavator has to be equipped with an overload warning device and itshoist cylinders with automatic check valves, according to the European Standard EN 474-5.
with stick 72Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
5.9h ( 5.9h )5.9h ( 5.9h )5.9h ( 5.9h )
6.1 ( 6.5h )6.5h ( 6.5h )6.5h ( 6.5h )
15.5+ (15.5+) 9.2 ( 9.6+) 5.7 ( 8.7 ) 3 .9 ( 5.8h )15.5+ (15.5+) 9.6+ ( 9.6+) 6.2 ( 8.8+) 4 .3 ( 5.8h )15.5+ (15.5+) 9.6+ ( 9.6+) 7.3 ( 8.8+) 5 .1 ( 5.8h )
13.4h (13.4h ) 8 .2 (12.4+) 5.3 ( 8.2 ) 3.5 ( 5.6 )13.4h (13.4h ) 8 .9 (12.4+) 5 .8 (10.2+) 3 .9 ( 5.9h )13.4h (13.4h ) 10.7 (12.4+) 6 .9 (10.2+) 4 .7 ( 5.9h )
10.4h (10.4h ) 7.6 (12.1 ) 4.9 ( 7.8 ) 3.4 ( 5.5 )10.4h (10.4h ) 8 .3 (15.9+) 5 .4 (11.7+) 3 .8 ( 7.1h )10.4h (10.4h ) 10.0 (15.9+) 6 .5 (11.7+) 4 .6 ( 7.1h )
13.1h (13.1 h ) 7.4 (12.0 ) 4.8 ( 7.7 ) 3.5 ( 5.6 )13.1h (13.1 h ) 8 .2 (18.1+) 5 .3 (13.1+) 3 .8 ( 7.5h )13.1h (13.1 h ) 9 .9 (18.1+) 6 .4 (13.1+) 4 .6 ( 7.5h )
13.6 (22.1h ) 7.3 (11.8 ) 4.7 ( 7.6 )15.2 (22.1h ) 8 .0 (18.7+) 5 .2 (13.5+)18.7 (22.1h ) 9 .7 (18.7+) 6 .3 (13.0 )
13.9 (24.1+) 7.4 (11.9 ) 4.8 ( 7.8 )15.5 (25.2+) 8 .1 (17.1+) 5 .3 (12.6+)
19.1 (25.2+) 9 .8 (17.1+) 6 .4 (12.6+)
14.6 (17.4+) 8 .4 (13.4 )16.3 (17.4+) 9 .3 (13.8+)17.4+ (17.4+) 11.1 (13.8+)
with stick 710Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
5.5h ( 5.5h )5.5h ( 5.5h )5.5h ( 5.5h )
6.2 ( 7.8+)6.7 ( 7.8+)7.8+ ( 7.8+)
15.5+ (15.5+) 9 .2 ( 9.5+) 5.7 ( 8.3+) 3.7 ( 5.1h )15.5+ (15.5+) 9.5+ ( 9.5+) 6.2 ( 8.3+) 4.0 ( 5.1h )15.5+ (15.5+) 9.5+ ( 9.5+) 7.3 ( 8.3+) 4.8 ( 5.1h )
13.0h (13.0h ) 8 .2 (11.8+) 5.3 ( 8.2 ) 3.5 ( 5.6 )13.0h (13.0h ) 9 .0 (11.8+) 5.8 ( 9.7+) 3.9 ( 7.1h )13.0h (13.0h ) 10.7 (11.8+) 6.9 ( 9.7+) 4.7 ( 7.1h )
10.5h (10.5h ) 7.5 (12.1 ) 4.9 ( 7.8 ) 3.3 ( 5.4 )10.5h (10.5h ) 8 .3 (15.5+) 5 .4 (11.3+) 3.7 ( 8.9h )10.5h (10.5h ) 10.0 (15.5+) 6 .5 (11.3+) 4.5 ( 8.9h )
13.2h (13.2h ) 7.4 (12.0 ) 4.8 ( 7.7 ) 3 .3 ( 5.4 )13.2h (13.2h ) 8 .2 (17.8+) 5 .3 (12.8+) 3.7 ( 7.2h )13.2h (13.2h ) 9 .9 (17.8+) 6 .4 (12.8+) 4.5 ( 7.2h )
13.5 (21.5h ) 7.2 (11.7 ) 4.6 ( 7.5 )15.0 (21.5h ) 7 .9 (18.7+) 5 .1 (13.4 )18.6 (21.5h ) 9 .6 (18.7+) 6 .2 (12.9 )
13.8 (23.9 ) 7.3 (11.8 ) 4.7 ( 7.6 )15.3 (25.8+) 8 .0 (17.4+) 5 .2 (12.3+)
18.9 (25.8+) 9 .7 (17.4+) 6 .3 (12.3+)
14.5 (19.3+) 7 .7 (12.3 )16.1 (19.3+) 8 .5 (13.5+)19.3+ (19.3+) 10.2 (13.5+)
with stick 810Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
4.9h ( 4.9h )4.9h ( 4.9h )4.9h ( 4.9h )
6.2 ( 7.0+) 3.9 (4.3h )6.7 ( 7.0+) 4.3 (4.3h )7.0+ ( 7.0+) 4.3h (4.3h )
9.4 ( 9.4+) 5.8 ( 7.7+) 3.7 (4.7h )9.4+ ( 9.4+) 6.3 ( 7.7+) 4.1 (4.7h )9.4+ ( 9.4+) 7.4 ( 7.7+) 4.7h (4.7h )
15.2 (15.4+) 8.3 (11.0+) 5.3 ( 8.2 ) 3.5 (5.6 )15.4+ (15.4+) 9.1 (11.0+) 5.8 ( 9.2+) 3.8 (8.5+)15.4+ (15.4+) 10.8 (11.0+) 6.9 ( 9.2+) 4.7 (8.5+)
12.5h (12.5h ) 7.6 (12.2 ) 4.8 ( 7.7 ) 3.3 (5.4 )12.5h (12.5h ) 8.3 (14.5+) 5.3 (10.9+) 3.7 (9.3+)12.5h (12.5h ) 10.0 (14.5+) 6.4 (10.9+) 4.4 (9.1 )
13.5 (13.7h ) 7.3 (11.9 ) 4.7 ( 7.6 ) 3.2 (5.3 )13.7h (13.7h ) 8.1 (17,2+) 5.2 (12.5+) 3.6 (9.4 )13.7h (13.7h ) 9.8 (17,2+) 6.3 (12.5+) 4.4 (9.0 )
13.3 (20.3h ) 7.1 (11.7 ) 4.6 ( 7.4 ) 3.3 (5.4 )14.9 (20.3h ) 7.9 (18.6+) 5.1 (13.3+) 3.6 (6.9h )18.4 (20.3h ) 9.6 (18.6+) 6.1 (12.8 ) 4.4 (6.9h )
13.6 (23.7 ) 7.1 (11.6 ) 4.6 ( 7.4 )15.2 (26.7+) 7.9 (17.6+) 5.1 (12.4+)18.7 (26.7+) 9.6 (17.6+) 6.2 (12.4+)
14.1 (20.7+) 7.5 (12.1 )15.7 (20.7+) 8.3 (13.8+)19.3 (20.7+) 9.9 (13.8+)
with stick 106Height Undercarriage Radius of load from centerline of machine in ft
ft 10 15 20 25
Stabilizers raisedStabil. blade down252 pt. outr. down
Stabilizers raisedStabil. blade down202 pt. outr. down
Stabilizers raisedStabil. blade down152 pt. outr. down
Stabilizers raisedStabil. blade down102 pt. outr. down
Stabilizers raisedStabil. blade down52 pt. outr. down
Stabilizers raisedStabil. blade down02 pt. outr. down
Stabilizers raisedStabil. blade down 52 pt. outr. down
Stabilizers raisedStabil. blade down 102 pt. outr. down
Stabilizers raisedStabil. blade down 152 pt. outr. down
4.4h ( 4.4h )4.4h ( 4.4h )4.4h ( 4.4h )
6.2 ( 6.4+) 3.5h (3.5h )6.4+ ( 6.4+) 3.5h (3.5h )6.4+ ( 6.4+) 3.5h (3.5h )
5.9 ( 6.6+) 3.8 (5.9 )6.4 ( 6.6+) 4.1 (6.8h )6.6+ ( 6.6+) 4.9 (6.8h )
15.2+ (15.2+) 8.5 ( 9.3+) 5.3 ( 8.1+) 3.5 (5.6 )15.2+ (15.2+) 9.3+ ( 9.3+) 5.8 ( 8.1+) 3.9 (7.7+)15.2+ (15.2+) 9.3+ ( 9.3+) 6.9 ( 8.1+) 4.7 (7.7+)
14.0 (15.0h ) 7.6 (12.2 ) 4.9 ( 7.8 ) 3.3 (5.3 )15.0h (15.0h ) 8.4 (13.4+) 5.4 (10.2+) 3.6 (8.7+)15.0h (15.0h ) 10.1 (13.4+) 6.5 (10.2+) 4.4 (8.7+)
13.6 (15.1h ) 7.4 (11.9 ) 4.7 ( 7.6 ) 3.2 (5.3 )15.1h (15.1h ) 8.1 (16.5+) 5.2 (11.8+) 3.5 (9.3 )15.1h (15.1h ) 9.8 (16.5+) 6.3 (11.8+) 4.3 (9.0 )
13.2 (18.7h ) 7.1 (11.6 ) 4.5 ( 7.3 ) 3.1 (5.2 )14.8 (18.7h ) 7.8 (18.2+) 5.0 (13.0+) 3.4 (9.2 )18.3 (18.7h ) 9.5 (18.2+) 6.1 (12.7 ) 4.2 (8.8 )
13.3 (23.3 ) 7.0 (11.5 ) 4.4 ( 7.3 )14.9 (26.1h ) 7.7 (18.1+) 4.9 (12.8+)18.4 (26.1h ) 9.4 (18.1+) 6.0 (12.7 )
13.8 (22.9+) 7.2 (11.7 ) 4.7 ( 7.7 )15.4 (22.9+) 7.9 (15.5+) 5.2 (11.5+)19.0 (22.9+) 9.6 (15.5+) 6.3 (11.5+)
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
10/14
Clamshell model 10 Bwithout ejector with ejector
Width of shells in 13 16 24 31 39 39 59 71 13 16 24 31Capacity SAE (heaped) cuyd 0.22 0.29 0.46 0.59 0.78 1.30 1.96 2.35 0.22 0.29 0.46 0.59
Max. material weight lb/cuyd 3000 3000 3000 3000 3000 3000 2000 2000 3000 3000 3000 3000
Weight incl. suspensionand hydr. swivel lb 1630 1740 1830 1940 2070 2230 2510 2780 1740 1850 2030 2180
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 810 7 2 5 7 106 106 810 7 2
Stabilizer blade down ft-in 106 106 10 6 810 5 7 106 106 10 6 7 2
2 point outriggers down ft-in 106 106 10 6 10 6 810 810 106 106 10 6 10 6
Blade + 2 pt. outr. down ft-in 106 106 10 6 10 6 10 6 10 6 810 57 106 106 10 6 10 6
4 point outriggers down ft-in 106 106 10 6 10 6 10 6 10 6 10 6 72 106 106 10 6 10 6
EW, stabilizers raised ft-in 106 106 10 6 810 7 2 5 7 106 106 10 6 810
EW, stabilizer blade down ft-in 106 106 10 6 10 6 7 2 5 7 106 106 10 6 10 6
EW, 2 point outriggers down ft-in 106 106 10 6 10 6 10 6 810 106 106 10 6 10 6
10
Clamshell Attachmentwith Hydr. Adjustable Boom
0 ft51015202530
0 m12345678910
25
20
15
10
5
0
-5
-10
-15
-20
-25
ft
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
m
1
234
5
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 57 72 710 810 106
Max. digging depth ft-in 196 212 22 7 22 9 245Max. reach at groundlevel ft-in 259 272 2710 2810 304Max. dumping height ft-in 174 186 1810 19 6 208
Camshell model: 10 BMax. tooth force: 73 kN (16300 lb)Max. torque of hydr. swivel: 1.76 kNm
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 72 stickand the clamshell model 10 B/0.59 cuyd.
Undercarriage versions lb
A 904 litronicwith stabilizer blade 39600A 904 litronicwith 2 pt. outriggers 40590A 904 litronicwith stabilizer blade + 2 pt . outr. 42700A 904 litronicwith 4 pt. outriggers 43120A 904 EW litronicwith stabilizer blade 39900A 904 EW litronicwith 2 pt. outriggers 40810
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
11/14
Clamshell model 10 Bwithout ejector with ejector
Width of shells in 13 16 24 31 39 39 59 71 13 16 24 31Capacity SAE (heaped) cuyd 0.22 0.29 0.46 0.59 0.78 1.30 1.96 2.35 0.22 0.29 0.46 0.59
Max. material weight lb/cuyd 3000 3000 3000 3000 3000 2000 2000 2000 3000 3000 3000 3000
Weight incl. suspensionand hydr. swivel lb 1630 1740 1830 1940 2070 2230 2510 2780 1740 1850 2030 2180
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 106 7 2 5 7 106 106 810 7 2
Stabilizer blade down ft-in 106 106 106 810 7 2 5 7 106 106 10 6 810
2 point outriggers down ft-in 106 106 106 10 6 10 6 810 106 106 10 6 10 6
Blade + 2 pt. outr. down ft-in 106 106 106 10 6 10 6 10 6 810 57 106 106 10 6 10 6
4 point outriggers down ft-in 106 106 106 10 6 10 6 10 6 810 72 106 106 10 6 10 6
EW, stabilizers raised ft-in 106 106 106 10 6 7 2 5 7 106 106 10 6 810
EW, stabilizer blade down ft-in 106 106 106 10 6 810 7 2 106 106 10 6 10 6
EW, 2 point outriggers down ft-in 106 106 106 10 6 10 6 810 5 7 106 106 10 6 10 6
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 5 7 72 710 810 10 6
Max. digging depth ft-in 20 0 217 2211 23 3 2411Max. reach at groundlevel ft-in 2511 274 28 0 29 0 30 6Max. dumping height ft-in 15 7 166 17 4 17 4 18 2
Camshell model: 10 BMax. tooth force: 73 kN (16320 lb)Max. torque of hydr. swivel: 1.76 kNm
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 72 stickand the clamshell model 10 B/0.59 cuyd.
Undercarriage versions lb
A 904 litronicwith stabilizer blade 37680A 904 litronicwith 2 pt. outriggers 38670A 904 litronicwith stabilizer blade + 2 pt. outr. 40790A 904 litronicwith 4 pt. outriggers 41210A 904 EW litronicwith stabilizer blade 37990A 904 EW litronicwith 2 pt. outriggers 38890
11
Clamshell Attachmentwith Gooseneck Boom 171
0 ft51015202530
0 m12345678910
1
234
5
25
20
15
10
5
0
-5
-10
-15
-20
-25
ft
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
m
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
12/1412
Ditchcleaning Attachmentwith Hydr. Adjustable Boom
0 ft51015202530
0 m12345678910
1
234
5
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
m
10
30
25
20
15
10
5
0
-5
-10
-15
-20
ft
Ditchcleaning bucketCutting width SAE mm 59 791) 79 95 79 (with 2 x 45h rotator)
Capacity SAE (heaped) cuyd 0.65 0.52 0.92 1.10 0.92Max. material weight lb/cuyd 3000 3000 3000 3000 3000
Weight of bucket lb 840 820 1100 1320 1540
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 5 7 5 7
Stabilizer blade down ft-in 106 106 810 7 2 7 2
2 point outriggers down ft-in 106 106 10 6 10 6 10 6
Blade + 2-pt. outr. down ft-in 106 106 10 6 10 6 10 6
4 point outriggers down ft-in 106 106 10 6 10 6 10 6
EW, stabilizers raised ft-in 106 106 10 6 7 2 810
EW, stabilizer blade down ft-in 106 106 10 6 810 10 6
EW, 2 point outriggers down ft-in 106 106 10 6 10 6 10 6
1) Bucket for narrow bottomed ditches
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 5 7 72 710 810 10 6
Max. digging depth ft-in 15 3 168 17 6 18 4 20 0Max. reach at groundlevel ft-in 25 1 266 27 4 28 2 2910Max. dumping height ft-in 19 8 239 24 1 24 9 2511
Max. teeth height ft-in 28 2 294 29 8 30 4 31 5
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 72 stickand the ditchcleaning bucket 0.92 cuyd.
Undercarriage versions lb
A 904 litronicwith stabilizer blade 38770A 904 litronicwith 2 pt. outriggers 39760A 904 litronicwith stabilizer blade + 2 pt . outr. 41870A 904 litronicwith 4 pt. outriggers 42290A 904 EW litronicwith stabilizer blade 39070A 904 EW litronicwith 2 pt. outriggers 39980
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
13/1413
Ditchcleaning Attachmentwith Gooseneck Boom 171
0 ft51015202530
0 m12345678910
1
234
5
30
25
20
15
10
5
0
-5
-10
-15
-20
ft
10
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
m
Ditchcleaning bucketCutting width SAE mm 59 791) 79 95 79 (with 2 x 45h rotator)
Capacity SAE (heaped) cuyd 0.65 0.52 0.92 1.10 0.92Max. material weight lb/cuyd 3000 3000 3000 3000 3000
Weight of bucket lb 840 820 1100 1320 1540
For machine stability per ISO 10567 the max. stick length is:
Stabilizers raised ft-in 106 106 810 5 7 7 2
Stabilizer blade down ft-in 106 106 810 7 2 810
2 point outriggers down ft-in 106 106 10 6 10 6 10 6
Blade + 2-pt. outr. down ft-in 106 106 10 6 10 6 10 6
4 point outriggers down ft-in 106 106 10 6 10 6 10 6
EW, stabilizers raised ft-in 106 106 10 6 7 2 810
EW, stabilizer blade down ft-in 106 106 10 6 810 10 6
EW, 2 point outriggers down ft-in 106 106 10 6 10 6 10 6
1) Bucket for narrow bottomed ditches
Digging Envelope1 stick 5 72 stick 7 23 stick 7104 stick 8105 stick 10 6
Stick length ft-in 5 7 7 2 710 810 10 6
Max. digging depth ft-in 15 9 17 4 1710 19 0 20 8Max. reach at groundlevel ft-in 25 3 2610 27 6 28 6 2910Max. dumping height ft-in 2010 21 9 22 7 22 7 23 5
Max. teeth height ft-in 26 5 27 3 28 0 28 0 29 0
Operating WeightThe operating weight includes the basic machine with8 tires plus spacer rings, hydr. adjustable boom, 72 stickand the ditchcleaning bucket 0.92 cuyd.
Undercarriage versions lb
A 904 litronicwith stabilizer blade 36850A 904 litronicwith 2 pt. outriggers 37840A 904 litronicwith stabilizer blade + 2 pt. outr. 39960A 904 litronicwith 4 pt. outriggers 40380A 904 EW litronicwith stabilizer blade 37160A 904 EW litronicwith 2 pt. outriggers 38060
8/14/2019 Technical Description Hydraulic Excavator Operating Weight 36850 45470
14/14
LIEBHERR Construction Equipment Co., 4100 Chestnut Avenue, Newport News,VA 23607, USA, (757) 245-5251, Fax (757) 9 28-8700, www.liebherr.com, e-Mail: [email protected]
With compliments:
LHB/VF8420685-2-09.0
0
PrintedinGermanyby
TypodruckGagstatter.
Illustrationsanddatamaydiffer
froms
tandardequipment.Subjecttochangewithoutno
tice.
Standard Equipment
Undercarriagex Two speed powershift transmission plus creeper speedx Creeper speed electrically switchable from cabx Two circuit travel brake with accumulatorx Proportional power steering with mechanical back upx Service free parking brake inside transmission (spring
activated)x Auto check valve directly on each stabilizer cylinderx Clam travel bracketx Lockable large rustfree storage boxx New tires
Uppercarriagex Engine hood with lift help, lockablex Lockable tool boxx Main switch for electric circuitx Handrails, non slip surfacesx Tool kitx Maintenance-free swing brake lockx Maintenance-free HD-batteriesx Sound insulationx Pin lock upper/lower
Hydraulicsx Electronic pump regulation at all R.P.M.x Four fixed modes, can also be adjustedx Pressure storage for controlled lowering of attachments
with engine turned offx Hydraulic tank shut-off valvex Pressure compensationx
Flow compensationx Filter with partial micro filtration (5 mm)x Hook ups for pressure checks
Enginex Direct injectionx Turbo chargerx Air filter with pre-cleaner main- and safety elementx Sensor controlled engine idling
Operator cabx Deep drawn cab shell componentsx Air conditionx All tinted windowsx Door with sliding windowx All-round adjustable roof ventx Rain hood over front window openingx Wiper/washer
x 6-way adjustable Liebherr seatx Seat and consoles independently adjustablex Cloth hookx Dome lightx Sun shadex Inside and outside rear mirrorx Cigarette lighter and ashtrayx Removable customized foot matx Storage compartmentx Warning lightsx Digital instruments for oil temp, engine R.P.M. and oil pressurex Additional hour meter, readable from outside
Attachmentx Cylinders with shock absorberx Sealed pivotsx Centralized lube pointsx SAE-dbl flange connection for all hi-pressure linesx Locking of connecting link during clam workx Safety lift hook on hoe bucketsx Hose quick connections for clam operationx Hydr. lines for clam operation on stickx Two way valves for bucket/clam usex Flood light on boom
Optional Equipment
x Independent outrigger controlx Second lockable rust free storage box in u/cx Customized colorsx Choice of tires
x Electric fuel tank filler pumpx Pedal controlled positioning swing brakex Extended tool kitx Customized colors
x Additional hydraulic circuitsx Bio degradable hydraulic oilx Full flow micro filtration
x Cold start aid
x Removable lower section of front window with storagex Preparation for radio installationx Stereo radiox Airpressure adjustable seatx Beaconx Optical and acoustical warning if outriggers are not fully
retracted
x Electronic drive away lockx Additional flood lightsx Fanx Bullet proof front window (fixed installation can not be
opened)
x Safety check valves for all attachment cylindersx Overload warning devicex Hydraulic or manual quick change tool adaptorx Liebherr line of clams and grapplesx Special buckets and other toolsx Customized colors
Options and/or special attachments, supplied by vendors other than Liebherr, may only beinstalled with the knowledge and approval of Liebherr to retain warranty.