TENDER DOCUMENTengineeringprojects.com/Tender/UploadFiles/3662_VOL_-_III.pdftrenches or drains (not...

TENDER DOCUMENT

NIT No.: NRO/CON/ALIMCO-FBD/752/677 dated 03.12.2018

FOR

Construction of Boundary Wall, 2 nos. gates & 2 nos. Guard room at ALIMCO’s new manufacturing set up of Aids and assisted devices at village Nawada Tigaon, Block Ballabgarh, district Faridabad (Haryana).

VOLUME – III

BOQ / PRICE BID

EXECUTING AGENCY

ENGINEERING PROJECTS (INDIA) LIMITED (A GOVT. OF INDIA ENTERPRISE)

Core-3, Scope Complex, 7,Lodhi Road, New Delhi-110003

TEL NO: 011-24361666, FAX NO. 011- 24363426

AN ISO 9001 & ISO 14001 COMPANY

In figures In words In figures In words

1 BOUNDARY WALL 10,635,759.66

2 02 Nos. MAIN GATE 1,060,119.36

302 Nos. SECURITY

ROOM 2,623,591.91

Total: 14,319,470.93

Rounded off 14,319,471.00

BIDDER'S FINANCIAL

OFFER :

In Figures

SEAL

In Words

SIGNATURE

* Bidders should submit separate sheet clearly showing base rate + GST / other Taxes, levies etc. as applicable.

* Rates should be inclusive of all taxes & duties and GST etc.

* Note-The Rates are based on DSR-2016, tenderer has to quote the rates above/ at par /below on DSR-2016 rates.

SL.No. ITEM

AMOUNT IN Rs. After adding percentage above/ below/ at par% QUOTE ABOVE/ BELOW / AT PAR ESTIMATED COST

(IN Rs.)

PRICE BID

BIDDER'S PRICE

Construction of Boundary Wall, 2 nos. gates & 2 nos. Guard room at ALIMCO’s new manufacturing set up of Aids and assisted devices at village Nawada

Tigaon, Block Ballabgarh, district Faridabad (Haryana).

SUMMARY OF COST

NRO/CON/ALIMCO-FBD/752/677


S.No DSR ITEMS 2016 AMOUNT

1 BOUNDARY WALL 10,635,759.66

2 MAIN GATE (MS GATE) 2 Nos 1,060,119.36

3 SECURITY ROOM 2 Nos 2,623,591.91

TOTAL 14,319,470.93

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF

AIDS AND ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON,

BALLABGARH, FARIDABAD ,HARYANA

SUMMARY OF BOUNDARY WALL,MAIN GATE & SECURITY ROOM


S.No

.

DSR ITEM

2016 Item Description Unit RATE Quantity Amount

EARTH WORK

1 2.8

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in foundation

trenches or drains (not exceeding 1.5 m in width or 10

sqm on plan), including dressing of sides and ramming

of bottoms, lift upto 1.5 m, including getting out the

excavated soil and disposal of surplus excavated soil

as directed, within a lead of 50 m.

2.8.1 All Kinds of soil CUM 166.40 576.89 95,994.50

2 2.25

Filling available excavated earth (excluding rock) in

trenches, plinth sides of foundations etc. in layers not

exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m

CUM 125.75 432.67 54,408.25

3 2.28

Surface dressing of the ground including removing

vegetation and inequalities not exceeding 15 cm deep

and disposal of rubbish, lead up to 50 m and lift up to

1.5 m.

2.28.1 All kinds of soil (100 SQM) SQM 1,395.00 8.21 11,452.95

CONCRETE WORK

4 4.1.

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

4.1.101:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded

stone aggregate 40 mm nominal size).CUM 4,209.05 158.49 667,095.07

REINFORCED CEMENT CONCRETE

5 5.1

Providing and laying in position specified grade of

reinforced cement concrete, excluding the cost of

centering, shuttering, finishing and reinforcement - All

work up to plinth level :

5.1.21:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded

stone aggregate 20 mm nominal size).CUM 6,215.35 5.00 31,076.75

5.9Centering and shuttering including strutting, propping

etc. and removal of form for :

6 5.9.1Foundations, footings, bases of columns, etc. for mass

concrete.sqm 193.95 536.00 103,957.20

7 5.9.5

Lintels, beams, plinth beams, girders, bressumers and

cantilevers

sqm 342.90 917.94 314,761.63

8 5.9.6Columns, Pillars, Piers, Abutments, Posts and Struts.

sqm 467.85 690.70 323,142.12

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND

ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD ,HARYANA

CIVIL WORK -TYPE -BOUNDARY WALL

Page 1 of 3


S.No

.

DSR ITEM


9 5.22

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars KG 56.60 7,600.00 430,160.00

10 5.22A


straightening, cutting, bending, placing in position and

binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars KG 56.60 7,500.00 424,500.00

5.33

Providing and laying in position machine batched and

machine mixed design mix M-25 grade cement

concrete for reinforced cement concrete work, using

cement content as per approved design mix, including

pumping of concrete to site of laying but excluding

the cost of centering, shuttering, finishing and

reinforcement, including admixtures in recommended

proportions as per IS: 9103 to accelerate, retard

setting of concrete, improve workability without

impairing strength and durability as per direction of

Engineer-in-charge.“(Note :- Cement content

considered in this item is @ 330 kg/cum.“Excess/ less

cement used as per design mix is payable/recoverable

separately).

11 5.33.1 All works upto plinth level cum 6,446.45 350.00 2,256,257.50

12 5.33.2 All works above plinth level upto floor V level cum 7,250.05 70.00 507,503.50

13 5.35

Add for using extra cement in the items of design mix

over and above the specified cement content therein. Quintal 672.75 150.00 100,912.50

BRICK WORK

14 6.2

Brick work with common burnt clay modular bricks of

class designation 7.5 in foundation and plinth in:

6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). CUM 4,400.50 300.00 1,320,150.00

15 6.4

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in

all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM 5,582.85 375.00 2,093,568.75

Page 2 of 3


S.No

.

DSR ITEM


STEEL WORK

16 16.53

Providing and fixing concertina coil fencing with punched

tape concertina coil 600 mm dia 10 metre openable

length ( total length 90 m), having 50 nos rounds per 6

metre length, upto 3 m height of wall with existing angle

iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9

horizontal R.B.T. reinforced barbed wire, stud tied with

G.I. staples and G.I. clips to retain horizontal, including

necessary bolts or G.I. barbed wire tied to angle iron, all

complete as per direction of Engineer-in-charge, with

reinforced barbed tape(R.B.T.) / Spring core (2.5mm

thick) wire of high tensile strength of 165 kg/ sq.mm with

tape (0.52 mm thick) and weight 43.478 gm/ metre (cost

of M.S. angle, C.C. blocks shall be paid separately)

metre 255.00 663.80 169,269.00

17 16.19

Supplying at site Angle iron post & strut of required size

including bottom to be split and bent at right angle in

opposite direction for 10 cm length and drilling holes

upto 10 mm dia. etc. complete.

KG 62.05 3,000.00 186,150.00

FINISHING

18 13.4 12 mm cement plaster of mix:

13.4.1 1:4 (1 cement: 4 coarse sand) sqm 180.85 4,000.00 723,400.00

19 13.42

Distempering with 1st quality acrylic distemper (ready

mixed) of approved manufacturer, of required shade

and colour complete, as per manufacturer's

specification.

13.42.1 Two or more coats on new work sqm 53.15 2,000.00 106,300.00

2013.46

Finishing walls with Acrylic Smooth exterior paint of

required shade :

13.46.1

New work (Two or more coat applied @ 1.67 ltr/10

sqm over and including priming coat of exterior

primer applied @ 2.20 kg/10 sqm)

sqm 96.05 4,000.00 384,200.00

2113.61

Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade :

13.61.1 13.61.1 Two or more coats on new work sqm 78.40 2,000.00 156,800.00

22 13.80

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

sqm 87.35 2,000.00 174,700.00

TOTAL 10635759.66

Page 3 of 3


S.No. DSR-16 Description Quantity Unit Rate Amount

1 10.25

Steel work welded in built up sections/

framed work, including cutting, hoisting,

fixing in position and applying a priming coat

of approved steel primer using structural

steel etc. as required.

10.25.2In gratings, frames, guard bar, ladder,

railings, brackets, gates and similar works

5,812.75 Kg 85.95 499,605.86

2 8.0

Marble work gang saw cut (polished and

machine cut) of thickness 18 mm for wall

lining (veneer work), backing filled with a

grout of average 12 mm thick in cement

mortar 1:3 (1 cement : 3 coarse sand),

including pointing with white cement mortar

1:2 (1 white cement : 2 marble dust)

with an admixture of pigment to match the

marble shade (To be secured to the backing

by means of cramps, which shall be paid for

separately).

8.1.1Raj Nagar Plain white marble/ Udaipur green

marble/ Zebra black marble.

8.1.1.2 Area of slab over 0.50 sqm 172.80 Sqm 3035.50 524,534.40

3 13.5 Applying priming coat:

13.50.4With ready mixed red oxide zinc chromate

primer of approved brand and manufacture

on steel work (second coat)

43.20 Sqm 15.60 673.92

-

4 13.62

Painting with synthetic enamel paint of

approved brand and manufacture of

required colour to give an even shade :

13.62.1

Two or more coats on new work over an

under coat of suitable shade with ordinary

paint of approved brand and manufacture

43.20 Sqm 112.30 4,851.36

Total 530,059.68

TOTAL GATE 2 Nos 1,060,119.36

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR

ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD ,HARYANA

SUMMARY OF MAIN GATE - 2 Nos


SUB

HEADDESCRIPTION AMOUNT

I CIVIL WORK 2,168,433.51

II ELECTRICAL 302,054.00

III PLUMBING 153,104.40

2,623,591.91


ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

SUMMARY SHEET OF SECURITY ROOM (OPTION -1)

TOTAL (in Rs.)

Page 1 of 1


S.No.DSR ITEM


EARTH WORK

1 2.8

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in foundation

trenches or drains (not exceeding 1.5 m in width or

10 sqm on plan), including dressing of sides and

ramming of bottoms, lift upto 1.5 m, including

getting out the excavated soil and disposal of surplus

excavated soil as directed, within a lead of 50 m.

2.8.1 All Kinds of soil CUM 166.4 56.3 9,360.00

2 2.25

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

CUM 125.8 42.2 5,305.08

3 2.28

Surface dressing of the ground including removing

vegetation and inequalities not exceeding 15 cm

deep and disposal of rubbish, lead up to 50 m and lift

up to 1.5 m.2.28.1 All kinds of soil SQM 13.95 13.5 188.33

4 2.35.3

Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart

including drilling 12 mm diameter holes and plugging

with cement mortar 1 :2 (1 cement : 2 Coarse sand)

to match the existing floor:

2.35.3.1With Chlorpyriphos/Lindane E.C. 20% with 1%

concentrationSQM 131.90 13.5 1,780.65

CONCRETE WORK

5 4.1.

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

4.1.81:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded

stone aggregate 40 mm nominal size)CUM 4,478.15 2.40 10,747.56

6 1.11

Providing and laying damp-proof course 50mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate

20mm nominal size).

SQM 320.25 16.00 5,124.00

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED

DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter

Page 1 of 5


S.No.DSR ITEM



7 4.17

Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) over

75mm thick bed of dry brick ballast 40 mm nominal

size, well rammed and consolidated and grouted

with fine sand, including necessary

excavation, levelling & dressing & finishing the top

smooth.

SQM 450.35 18.00 8,106.30

REINFORCED CEMENT CONCRETE

8 5.1

Providing and laying in position specified grade of

reinforced cement concrete, excluding the cost of

centering, shuttering, finishing and reinforcement -

All work up to plinth level :

5.1.2

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3

graded stone

aggregate 20 mm nominal size).

CUM 6215.35 8.00 49722.80

5.33

Providing and laying in position machine batched and

machine mixed design mix M-25 grade cement concrete

for reinforced cement concrete work, using cement

content as per approved design mix, including pumping

of concrete to site of laying but excluding the cost of

centering, shuttering, finishing and reinforcement,

including admixtures in recommended proportions as

per IS: 9103 to accelerate, retard setting of concrete,

improve workability without impairing strength and

durability as per direction of Engineer-in-charge.“(Note :-

Cement content considered in this item is @ 330

kg/cum.“Excess/ less cement used as per design mix is

payable/recoverable separately).

9 5.33.1 All works upto plinth level cum 6,446.45 8.00 51,571.60

10 5.33.2 All works above plinth level upto floor V level cum 7,250.05 10.00 72,500.50

11 5.35

Add for using extra cement in the items of design mix

over and above the specified cement content therein. Quintal 672.75 15.00 10,091.25

5.9Centering and shuttering including strutting,

propping etc. and removal

of form for all heights :12 5.9.1

Foundations, footings, bases of columns, etc. for

mass concrete.SQM 193.95 120.00 23274.00

135.9.3

Suspended floors, roofs, landings, balconies and

access platformSQM 422.30 140.62 59383.83

14

5.9.5

Lintels, beams, plinth beams, girders, bressumers

and

cantilevers

SQM 342.90 95.00 32575.50

155.9.6

Columns, Pillars, Piers, Abutments, Posts and Struts.SQM 467.85 140.00 65499.00

Page 2 of 5


S.No.DSR ITEM



5.22A


straightening, cutting, bending, placing in position

and binding all complete above plinth level.

165.22A.6

Thermo-Mechanically Treated bars of grade Fe-500 D

or more.KG 56.60 2600.00 147160.00

BRICK WORK

17 6.4

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level

in all shapes and sizes in :6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM 5582.85 8.34 46574.37

ALUMINIUM WORK

18 21.1

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat

angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately)

21.1.1 For fixed portion

21.1.1.2Powder coated aluminium (minimum thickness

of powder coating 50 micron)KG 384.50 450.00 173025.00

19 21.1.2

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever

required including the cost of EPDM rubber /

neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.1

Anodised aluminium (anodised transparent

or dyed to required shade according to IS:

1868, Minimum anodic coating of grade AC 15)

21.1.2.2Powder coated aluminium (minimum thickness

of powder coating 50 micron)KG 444.90 360.00 160164.00

Page 3 of 5


S.No.DSR ITEM



20 21.3

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per

the architectural drawings and the directions of

Engineer-in-charge . (Cost of aluminium snap

beading shall be

paid in basic item):21.3.2 With float glass panes of 5.50 mm thickness SQM 1003.95 18.00 18071.10

FLOORING

21 11.26

Kota stone slab flooring over 20 mm (average) thick

base laid over and jointed with grey cement slurry

mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base

of cement mortar 1 : 4 (1 cement : 4 coarse sand) :11.26.1 25 mm thick SQM 1158.1 12.00 13897.2

22 11.36

Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge,

in skirting, risers of steps and dados, over 12 mm

thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

SQM 744.8 36.00 26812.80

23.0 11.37

Providing and laying Ceramic glazed floor tiles of size

300x300 mm (thickness to be specified by the

manufacturer) of 1st quality conforming to IS : 15622

of approved make in colours such as White, Ivory,

Grey, Fume Red Brown, laid on 20 mm thick cement

mortar 1:4 (1 Cement : 4 Coarse sand), jointing with

grey cement slurry @ 3.3kg/sqm including pointing

the joints with white cement and matching pigment

etc., complete

SQM 688.35 18.00 12390.30

ROOFING

Page 4 of 5


S.No.DSR ITEM



24 12.55

Providing and fixing Heat Resistant Terrace Tiles (300

mm x 300 mm x 20 mm) with SRI (solar refractive

index) > 78, solar reflection > 0.70 and initial

emittance > 0.75 on waterproof and sloped surface

of terrace, laid on 20 mm thick cement sand mortar

in the ratio of 1:4 (1 cement : 4 coarse sand) and

grouting the joints with mix of white cement &

marble powder in ratio of 1:1, including rubbing and

polishing of the surface upto 3 cuts complete,

including providing skirting upto 150 mm height

along the parapet walls in the same manne

SQM 1150 13.50 15525.00

FINISHING

25 13.4 12 mm cement plaster of mix:

13.4.1 1:4 (1 cement: 4 coarse sand) sqm 180.85 135.00 24414.75

26 13.80

Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

sqm 87.35 135.00 11792.25

27 13.42

Distempering with 1st quality acrylic distemper

(ready mixed) of approved manufacturer, of required

shade and colour complete, as per manufacturer's

specification.13.42.1 Two or more coats on new work sqm 53.15 135.00 7175.25

28 13.60

Wall painting with acrylic emulsion paint of approved


13.60.1 Two or more coats on new work sqm 84.45 135.00 11400.75

29

13.61

Painting with synthetic enamel paint of approved


13.61.1 13.61.1 Two or more coats on new work sqm 78.40 135.00 10584.00

TOTAL 1,084,216.76

SECURITY 2 Nos 2,168,433.51

Page 5 of 5


SECTION DESCRIPTION AMOUNT (AS PER DSR 2016)

I SANITARY INSTALLATIONS 28307.50

II INTERNAL DRAINAGE 59184.45

III WATER SUPPLY 20945.85

IV EXTERNAL DRAINAGE 44666.60

NET TOTAL COST 153104.40


ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD,

HARYANA

PLUMBING WORKS


S.NO DESCRIPTION QTY. UNIT RATE AMOUNT

DSR 2016. ITEMS:-

1 17.2

Providing and fixing white vitreous china pedestal

type water closet (European type W.C. pan) with

seat and lid, 10 litre low level white P.V.C. flushing

cistern, including flush pipe, with manually

controlled device (handle lever), conforming to IS :

7231, with all fittings and fixtures complete,

including cutting and making good the walls and

floors wherever required :

17.2.1.W.C. pan with ISI marked white solid plastic seat and

lid2.00 Each 3418.70 6,837.40

2 17.3

Providing and fixing white vitreous china pedestal

type water closet (European type) with seat and lid,

10 litre low level white vitreous china flushing

cistern & C.P. flush bend with fittings & C.I.brackets,

40 mm flush bend, overflow arrangement with

specials of standard make and mosquito proof

coupling of approved municipal design complete,

including painting of fittings and brackets, cutting

and making good the walls and floors wherever

required :

17.3.1W.C. pan with ISI marked white solid plastic seat and

lid2.00 Each 4593.75 9,187.50

3 17.7

Providing and fixing wash basin with CI

brackets,15mm brass pillar taps,32mm CP brass

waste of standard pattern, including painting of

fittings and brackets,cutting and making good the

walls wherever required.

17.7.2White Vitreous China Wash basin size 630x450 mm

with a single 15 mm C.P. brass pillar tap2.00 Each 2020.60 4041.20

4 17.28Providing and fixing P.V.C waste pipe for sink or

wash basin including P.V.C waste fitting complete .

Flexible pipe

17.28.2.2 a) 40 mm dia 10 Each 81.40 814.00

5 17.29Providing and fixing 100mm sand cast iron grating

for gully trap.2 Each 29.25 58.50

6 17.31

Providing and fixing 600x450mm beveled edge

mirror of superior glass (of approved quality)

complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws

and washers complete.

2.00 Each 817.95 1,635.90


ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

SUB HEAD I : SANITARY INSTALLATIONS

Plumbing Work

Page 1 of 7



Plumbing Work

7 17.33Providing and fixing 600 x 120 mm glass shelf with

CP brass brackets and guard rail complete, fixed to

wooden cleadts with CP brass screws.

Each 573.30 -

8 17.34 Providing and fixing toilet paper holder.17.34.1 a) CP Brass 2 Each 385.35 770.70

9 17.60

Providing and fixing trap of self cleansing design

with screwed down or hinged grating with or

without vent arm complete, including cost of cutting

and making good the walls and floors17.60.1 100 mm inlet and 100 mm outlet

17.60.1.3Hubless centrifugally cast (spun) iron pipes epoxy

coated inside & outside IS: 159054 Each 677.70 2,710.80

17.60.2 100 mm inlet and 75 mm outlet


coated inside & outside IS: 159052 Each 496.40 992.80

10 17.70Providing and fixing PTMT Bottle Trap for Wash

basin and sink.

17.70.1

Bottle trap 31 mm single piece moulded with height

of 270 mm, effective length of tail pipe 260 mm

from the centre of the waste coupling, 77 mm

breadth with 25 mm minimum water seal, weighing

not less than 260 gms

2 Each 293.95 587.90

11 17.71

Providing and fixing PTMT liquid soap container 109

mm wide,125 mm high and 112 mm distance from

wall of standard shape with bracket of the same

materials with snap fittings of approved quality and

colour, weighing not less than 105 gms.minimum

water seal, weighing not less than 263 gms

2 Each 137.85 275.70

12 17.72

Providing and fixing PTMT towel ring trapezoidal

shape 215 mm long, 200 mm wide with minimum

distances of 37 mm from wall face with concealed

fittings arrangement of approved quality and

colour,weighing not less than 88 gms

2 Each 197.55 395.10

TOTAL (As per DSR. Items) 28,307.50

DSR 2016. ITEMS:-

1 17.35Providing and fixing soil, waste and vent pipes and

rain water pipes conforming to IS 1729.17.35.1 100 mm dia 30.00 Metre 925.55 27,766.50


coated inside & outside IS: 1590517.35.2 75 mm dia 5.00 Metre 759.80 3,799.00


coated inside & outside IS: 15905

SUB-HEAD II : INTERNAL DRAINAGE

Page 2 of 7



Plumbing Work

2 17.36Providing and filling the joints with spun yarn,

cement slurry and cement mortar 1:2 ( 1 cement : 2

fine sand) in S.C.I./ C.I. Pipes :17.36.1 75 mm dia 5.00 Each 72.95 364.75

17.36.2 100 mm dia 30.00 Each 85.95 2,578.50

3 17.37

Providing and fixing M.S. holder-bat clamps of

approved design to sand cast iron/cast iron (spun)

pipe embedded in and including cement concrete

block 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2

coarse sand: 4 graded stone aggregate 20mm

nominal size) including cost of cutting holes and

making good the walls etc.

17.37.1 For 100 mm dia pipe 10.00 Each 167.35 1,673.50

17.37.2 For 75 mm dia pipe 2.00 Each 165.05 330.10

4 17.38Providing and fixing bend of required degree with

access door, insertion rubber washer 3 mm thick,

bolts and nuts complete:17.38.1 100 mm dia 10.00 Each 489.45 4,894.50


coated inside & outside IS: 1590517.38.2 75 mm dia 2.00 Each 391.05 782.10



5 17.39 Providing and fixing plain bend of required degree.

17.39.1 100 mm dia 10.00 Each 307.10 3,071.00


coated inside & outside IS: 1590517.39.2 75 mm dia 2.00 Each 212.20 424.40

17.39.2.3 75 mm dia sand cast iron S&S as per 1729

6 17.42.1Providing and fixing double equal plain junction of

required degree.

17.42.1 100x100x100 * 100 mm 5.00 Each 645.10 3,225.50



7 17.44Providing and fixing single equal plain junction of

required degree.

17.44.1 100x100x100 * 100 mm 5.00 Each 503.40 2,517.00



8 17.48Providing and fixing single unequal plain junction of

required degree.

17.48.1 100x100x75 mm 2.00 Each 482.45 964.90


coated inside & outside IS: 15905 Page 3 of 7



Plumbing Work

9 17.49Providing and fixing double equal plain invert

branch of required degree.

17.49.1 100x100x100 * 100 mm 2.00 Each 785.60 1,571.20



10 17.50Providing and fixing single equal plain invert branch

of required degree. 17.50.1 100x100x100 * 100 mm 2.00 Each 503.40 1,006.80



11 17.56.1 Providing and fixing terminal guard- 100mm 2.00 Each 355.85 711.70



12 17.57AProviding and fixing shielded coupling for hubless

centrigugally cast iron pipe

17.57.A.1 100 mm dia 5.00 Each 360.50 1,802.50

17.57.A.1.1 SS304 grade coupling with EPDM rubber gasket

17.57.A.2 75 mm dia 1.00 Each 326.00 326.00

17.57.A.2.1 SS304 grade coupling with EPDM rubber gasket

13 17.65

Painting sand cast iron/centrifugally cast (spun) iron

soil, waste vent pipes and fittings with paint of any

colour such as chocolate grey, or buff etc. over a

coat of primer (of approved quality) for new work.

17.65.1 100 mm diameter pipe 30.00 Meter 40.65 1,219.50

17.65.2 75 mm diameter pipe 5.00 Meter 31.00 155.00

TOTAL (As per BSR. Items) 59,184.45

P.W.D. ITEMS:-

1 18.8

Providing and fixing Chlorinate Polyvinyl Chloride

(CPVC) pipes having thermal stability for hot & cold

water supply including all CPVC plain & brass

threaded fittings i/c fixing the pipe with clamps at

1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the the

same including testing of joints complete as per

direction of engineer in charge.

SUB HEAD III: WATER SUPPLY

Page 4 of 7



Plumbing Work

Concealed work oncluding cutting chases and

making good the walls etc.18.8.1 15 mm outer dia pipes. 15.00 Metre 246.20 3,693.00

18.8.2 20 mm outer dia pipes. 20.00 Metre 284.85 5,697.00

2 18.16Providing and fixing brass stop cock of approved

quality complete.18.16.1 15 mm nominal bore 5.00 Each 260.10 1,300.50

18.16.2 20 mm nominal bore 5.00 Each 280.40 1,402.00

3 18.17Providing and fixing gun metal gate valve with C.I.

wheel of approved quality (screwed end):18.17.1 25 mm dia nominal bore 2.00 Each 428.20 856.40

18.17.2 32 mm dia nominal bore 1.00 Each 500.75 500.75

4 1.18.48

Providing and placing on terrace (at all floor levels)

Polyethylene water storage tank ISI : 12701 marked

with cover and suitable locking arrangement amd

making necessary holes for inlet, outlet and

overflow pipes but without fittings and the base

support for tank

400.00 Litre 7.25 2,900.00

5 18.49Providing and fixing C.P.brass bib cock of approved

quality conforming to IS : 8931.8 Each 481.60 3,852.80

6 18.51Providing and fixing C.P.brass long body bib cock of

approved quality conforming to IS standard and

Weighing not less than 690 gms. 18.51.1 15 mm nominal bore. 2 Each 371.70 743.40

7 18.53

Providing and fixing C.P. bass angle valve for basin

mixer and geyser points of approved quality

conforming to I.S:8931 a) 15 mm nominal bore

18.53.1 15 mm nominal bore Each 475.70 -

TOTAL 20,945.85

1 19.4

Providing and fixing square-mouth S.W. gully trap

Class SP-1 complete with C.I. grating brick masonry

chamber with grating brick masonry chamber with

water tight C.I. cover with frame of 300 x300 mm

size (inside) the weight of cover to be not less than

4.50 kg and frame to be not less than 2.70 kg as per

standard design :19.4.2 150x100mm size P type 2.00 Each 1623.25 3,246.50

19.4.2.1With common burnt clay F.P.S (non - modular)

bricks of class designation 7.519.4.3 180x150mm size P type Each 1623.25 -


bricks of class designation 7.5

SUB HEAD IV: DRAINAGE- EXTERNAL

Page 5 of 7



Plumbing Work

2 19.6

Providing and laying non-pressure NP2 class (light

duty) R.C.C. pipes with collars jointed with stiff

mixture of cement mortar in the proportion of 1:2

(1 cement : 2 fine sand) including testing of joints

etc. complete.19.6.1 100 mm dia R.C.C. Pipe 20.00 Metre 325.55 6,511.00

19.6.2 150 mm dia R.C.C. Pipe Metre 356.00 -

19.6.3 250 mm dia R.C.C. Pipe Metre 482.05 -

3 19.70

Constructing brick masonry manhole in cement

mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top

slab with 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size),

foundation in cement concrete 1:4:8 mix (1 cement :

4 coarse sand : 8 graded stone aggregate 40mm

nominal size) inside plastering 12mm thick with

cement mortar 1:3

(1 cement : 3 coarse sand) finished with floating

coat of neat cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) finished with a

floating coat of neat cement complete as per

standard design :

19.7.1

Inside size 90 x 80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455 x 610 mm internal

dimensions total weight of cover and frame to be

not less than 38 kg (weight of cover 23 kg and

weight of frame 15 kg).


bricks of class designation 7.52.00 Each 8634.10 17,268.20

4 19.27

Providing and constructing brick masonry road gully

chamber 50x45x60 cm with bricks in cement

mortar 1:4 (1 cement : 4 coarse sand) including

500x450 mm precast R.C.C. horizontal grating with

frame complete as per standard design.

19.27.1With common burnt clay F.P.S (non - modular)

bricks of class designation 7.52.00 Each 4043.10 8,086.20

Page 6 of 7



Plumbing Work

5 19.30

Providing and constructing brick masonry chamber

for undergroundCI inspection chamber and bends

with bricks in cement mortar 1:4 (1 cement : 4

coarse sand) C.I. cover with frame (light duty)

455x610 mm internal dimensions, total weight of

cover with frame to be not less than 38 kg (weight

of cover 23 kg and weight of frame 15 kg) R.C.C. top

slab with 1:2:4 mix (1 cement :2 coarse sand : 4

graded stone aggregate 20 mm nominal size)

foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement mortar

1:3 (1 cement : 3 coarse sand) finished smooth with

a floating coat of neat cement on walls and bed

concrete etc. complete as per standard design :

19.30.1Inside dimensions 455x610 mm and 45 cm deep for

single pipe line :2.00 Each 4777.35 9,554.70

19.30.1With common burnt clay F.P.S (non - modular)

bricks of class designation 7.5

TOTAL 44,666.60

Page 7 of 7


SUB

HEADDESCRIPTION

AMOUNT (DSR 2018

Items)

(In Rs.)

AMOUNT (NS Items)

(In Rs.)

I POINT WIRING 96,854.00 21,500.00

II DISTRIBUTION BOARDS 12,744.00

III LT CABLE 3,516.00 9,040.00

IV SUPPLY OF LIGHTING FIXTURES 94,600.00

V CCTV SYSTEM 63,800.00

113,114.00 188,940.00

302,054.00 GRAND TOTAL (in Rs.)

SUMMARY SHEET OF ELECTRICAL WORKS

TOTAL (in Rs.)

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED

DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA


S.No.DSR Item

CodeDescription Unit Qty Rate Amount REMARKS

1 1.10

Wiring for light point/Ceiling/Wall fan point

/exhaust fan/call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single

core cable in surface/ recessed PVC conduit

with modular switch modular plate suitable GI

box and earthing the point with 1.5 sq.mm


core cable etc.as required.

1.10.3 Group C Point 34 990.00 33660.00

2 1.11

Wiring for twin control light point with 1.5

sq.mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed PVC

conduit with 2 way modular switch modular

plate suitable GI box and earthing the point

with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc.as required.

Point 2 1057.00 2114.00

3 1.12

Wiring for light/ power plug with 2X4 sq. mm


core cable in surface/ recessed medium class

PVC conduit along with 1 No 4 sq. mm FRLS

PVC insulated copper conductor single core

cable for loop earthing as required.

Mtr. 80 200.00 16000.00

4 1.13

Wiring for light/ power plug with 4X4 sq. mm


core cable in surface/ recessed medium class

PVC conduit along with 2 Nos 4 sq. mm FRLS

PVC insulated copper conductor single core

cable for loop earthing as required.

Mtr. 20 308.00 6160.00

5 1.14

Wiring for circuit/ sub main wiring along with

earth wire with the following sizes of PVC

insulated copper conductor, Single core cable

in surface/ recessed PVC conduit as required

a 1.14.2 2x 2.5 sqmm+ 1x 2.5 sqmm earth wire Mtr. 120 167.00 20040.00b 1.14.3 2x 4 sqmm+ 1x 4 sqmm earth wire Mtr. 0 200.00 0.00c 1.14.4 2x 6 sqmm+ 1x 6 sqmm earth wire Mtr. 0 249.00 0.00c 1.14.5 2x 10 sqmm+ 1x 6 sqmm earth wire Mtr. 0 328.00 0.00d 1.14.8 4x 4 sqmm+ 2x 4 sqmm earth wire Mtr. 0 308.00 0.00e 1.14.9 4x 6 sqmm+ 2x 6 sqmm earth wire Mtr. 0 394.00 0.00f 1.14.10 4x 10 sqmm+ 2x 6 sqmm earth wire Mtr. 0 543.00 0.00g 1.14.11 4x 16 sqmm+ 2x 6 sqmm earth wire Mtr. 0 752.00 0.00

6 1.18

Telephone wiring in existing conduiting:

Supply & drawing following pair, 0.5 sq.mm

FRLS PVC insulated copper conductor,

unarmoured telephone cable in existing

surface/ recessed steel/ PVC conduit as

required.a 1.18.2 2 pair Mtrs. 60 20.00 1200.00b 1.18.3 4 pair Mtrs. 0 29.00 0.00

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR ALIMCO AT

NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

ELECTRICAL BOQ

Sub-Head-I : Circuit Cum Point Wiring ( DSR Items)

Page 1 of 3


S.No.DSR Item


ELECTRICAL BOQ

7 1.21

Supply & fixing of following sizes of PVC conduit

along with accessories in surface / recessed

including cutting the wall & making good the

same in case of recessed conduit as required.

a 1.21.1 20 mm dia. Mtrs. 0 84.00 0.00b 1.21.2 25 mm dia. Mtrs. 40 90.00 3600.00c 1.21.3 32 mm dia. Mtrs. 0 92.00 0.00d 1.21.4 40 mm dia. Mtrs. 0 130.00 0.00e 1.21.5 50 mm dia. Mtrs. 0 158.00 0.00

8 1.24

Supplying and fixing following modular switch/

socket on the existing modular plate & switch

box including connections but excluding

modular plate etc. as required.1.24.1 5/6 A switch Each 4 85.00 340.00

1.24.3 15/16 A switch Each 2 132.00 264.00

1.24.4 3 pin 5/6 A socket outlet Each 4 111.00 444.00

1.24.5 6 pin 15/16 A socket outlet Each 2 175.00 350.00

1.24.6 Telephone socket outlet Each 2 119.00 238.00

1.24.7 TV antenna socket outlet Each 0 119.00 0.00

1.24.8 Bell push Each 0 126.00 0.00

9 1.25

Supplying and fixing two module of Stepped

type electronic fan regulator on the existing

modular plate & switch box including

connections but excluding modular plate etc. as

reqd.

Each 2 342.00 684.00

10 1.26

Supplying and fixing of modular Blanking plate

on the existing modular plate & switch box

including connections but excluding modular

plate etc. as reqd.

Each 4 32.00 128.00

11 1.27

Supply and fixing of following size/ modules, GI

box along with modular base & cover plate for

modular switch/ regulator in recess, including

connection as required.1.27.1 1or 2 module (75mmx 75mm) Each 6 243.00 1458.001.27.1 3 Module (100 mmX75 mm) Each 0 267.00 0.001.27.1 4 Module (125 mmX75 mm) Each 0 287.00 0.001.27.1 6 Module (200 mmX75 mm) Each 0 333.00 0.001.27.1 8 Module (125 mmX125 mm) Each 4 383.00 1532.001.27.1 12 Module (200 mmX150 mm) Each 0 434.00 0.00

12 1.33Supply and fixing of 3 Pin ,5amp ceiling rose on

the existing junction box /wooden block

including connection etc as required.

Each 2 65.00 130.00

13 1.41

Installation, testing & commissioning of pre-

wired, fluorescent fitting / compact fluoroscent

fitting of all type, complete with all accessories

& tubes etc. directly on ceiling / wall, including

connection with 1.5 sq.mm. FRls PVC insulated,

copper condutor, single core cable and earthing

etc. as required.

Each 34 168.00 5712.00

Page 2 of 3


S.No.DSR Item


ELECTRICAL BOQ

14 1.42

Installation, testing and commissioning of pre-

wired, fluorescent fitting/ compact fluorescent

fitting of all types, with all accessories and tube

etc., including supplying and fixing ball and

socket arrangement, 2 no. down rods of 20 mm

dia X 1.6 mm thick steel conduit upto 30 cm

length, painting and wiring the down rods and

connection with 1.5 sq. mm FRLS PVC insulated,

copper conductor, single core cable and

earthing etc as required.

Each 2 358.00 716.00

15 1.45

Installation, testing & commissioning of ceiling

fan including wiring the down rods of standard

length ( upto 30 cm) with 1.5 sq.mm FRLS PVC

insulated, copper conductor, single core cable,

including providing and fixing phenolic

laminated sheet cover on the fan box etc. as

reqd.

Each 2 203.00 406.00

16 1.49Numbering of ceiling fan/ exhaust fan/

fluorescent fittings as required.Each 34 28.00 952.00

17 1.50

Installation of Exhaust/Wall fan in the existing

opening , including making the hole to suit the

size of the above fan, making good the damage

connection, testing commissioning etc. as

required. 1.50.1 Upto 450 mm sweep Each 2 363.00 726.00

96854.00

1 NSI

Supply, installation, testing and commissioning

of following krone type tag blocks enclosed in

MS enclosure of suitable size with lockable

cover.a 10 pair Tag block No 2 1500.00 3000.00

2 NSI

Supply, laying, testing and commissioning of

following size of 0.6mm dia copper conductor

multi pair telephone cable as per suitable for

indoor telephone wiring conforming for ITD

S/WS - 113 C and S/WS - 114 (actual qty. may

vary as per site) in existing conduit/ trench/

tray.

a5 pair Armoured. Cable (Incoming from BSNL

TAG BLOCK)RM 80 150.00 12000.00

3 NSISupplying, drawing, connecting & testing of 4

pair CAT-6 (E) wire for Data Outlet in existing

conduit

Mtrs. 80 65 5200.00

4 NSISupply, fixing, testing & commisssioning of

Modular RJ-45 with data outlet socket with grid

& cover plate in suitable size of 16 SWG GI box.

Nos 2 650 1300.00

21500.00Total of Sub-Head - I carried to summary sheet (NSI Item)

Total of Sub-Head - II carried to summary sheet (DSR Item)

Sub-Head -I : Circuit Cum Point Wiring (Non Schedule Items)

Page 3 of 3


S.NO. SR Item Code Description Unit Qty Rate Amount REMARKS

1 2.3

Supplying and fixing following way, single pole

and neutral, sheet steel, MCB distribution board,

240 V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including

earthing etc. as required. (But without

MCB/RCCB/Isolator)

a 2.3.1 6 way, Double door Each 0 1661.00 0.00

b 2.3.2 8 way, Double door Each 0 1760.00 0.00

c 2.3.3 12 way, Double door Each 2 2053.00 4106.00

2 2.10

Supplying & fixing 5 amps to 32 amps rating 240

volts C curve, Miniature Circuit Breaker suitable

for lighting loads of following poles in the

existing MCB DB complete with connections,

testing and commissioning etc. as required.

a 2.10.1 Single Pole Each 20 199.00 3980.00

3 2.11Supply and fixing single pole blanking plate in

the existing MCB DB complete etc. as required.Each 2.00 8.00 16.00

4 2.14

Supplying and fixing following rating, double

pole, (single phase and neutral), 240 volts,

residual current circuit breaker (RCCB), having a

sensitivity current upto 300 milliamperes in the

existing MCB DB complete with connections,

testing and commissioning etc. as required.

a 2.14.1 25A Each 0 1927.00 0.00

b 2.14.2 40A Each 2 2095.00 4190.00

c 2.14.3 63A Each 0 2640.00 0.00

5 2.21

Providing and fixing M.V. danger notice plate of

200x150mm ,made of mild steel at least 2mm

thick ,vitreous enameled white on both sides

,and with inscription in single red colour on front

side as required.

Each 2.00 226.00 452.00

12744.00

ELECTRICAL BOQ

Sub-Head-II: Distribution Boards (DSR Items)

Total of Sub-Head - II carried to summary sheet (DSR Item)

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR ALIMCO AT

NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA


S.N0.SR Item

CodesDescription Unit Qty Rate Amount

1 7.7 Laying and fixing one Number PVC

insulated and PVC sheathed/XLPE

power cable of 1.1 KV grade of

following size on cable tray as

required.

7.7.1 Upto 35 Sq. mm Meter 80 39.00 3,120.00

2 9.1 Supplying & making of end

terminations with brass compression

gland and Al. lugs for following sizes

of PVC insulated and PVC sheathed/

XLPE Al. conductor cable of 1.1 KV

grade as required.

a) 9.1.1 2 x 6 sq.mm. Each 2 198.00 396.00

3,516.00

1 NSI Supply of following sizes of XLPE/ PVC

insulated Aluminum/ Copper

conductor strip/ wire Armoured,

overall PVC sheathed 1.1 KV grade

cables conforming to relevant IS code

and technical specifications.

1.1 NSI XLPE insulated Al. Ar.Cable

a) 2 x 6 sq.mm. Metre 80 113 9,040.00

9,040.00

.Total of Sub-Head - III carried to summary sheet (NSI Item)

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES

FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

ELECTRICAL BOQ

Sub-Head -III : L.T Cables ( DSR Items)

Total of Sub-Head - III carried to summary sheet (DSR Item)

Sub-Head-VII: L.T Cables (Non- Schedule Items)


S.NO. Description Unit Qty. Rate Amount REMARKS

Sub-Head - IV: Supply & Fixing of Light Fixtures ( Non DSR Items)

Supply & fixing of following fans & Light

fittings with Electronic Ballast (THD<10%,

HF-P), starter, control gears, lamps holder,

transformer etc. as called for and flexible

wires as required for fixing including

providing of Lamps as required.

1

20 Watt LED TUBE LIGHT Fitting ( 20W

ENDURA LINEAR NEO-MODEL NO-

LHEWEBP6IN1W020 -HAVELLS MAKE or

equivalent)

Each 4 1335.00 5340.00

2

6 Watt LED Light Fitting ( 6W BOLT ROUND

(SURFACE) LED-MODEL NO.-

LHEAARP7UL1W006 - HAVELLS MAKE or

equivalent)

Each 6 1125.00 6750.00

3

30 Watt LED Light Fitting (JETA NEO 30 &

50 LED IP65-MODEL NO.-

LHEPBFUEIN6W030 - HAVELLS MAKE or

equivalent)

Each 20 3850.00 77000.00

4

1200mm sweep 3 blade Ceiling fan

complete with assembling of blades, down

rod, shackle insulator, canopy etc. ( SS-390 -

HAVELLS MAKE)

Each 2 1560.00 3120.00

5Exhaust Fan 250 mm ( VENTIL AIR-DX -

HAVELLS MAKE)250mm Each 2 1195.00 2390.00

94600.00

ELECTRICAL BOQ

Total For Internal Lights

ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES

FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA


SUB-V

A. CCTV SYSTEM

1 Bullet cameras

Supply, installation, testing and commissioning of IP

based, 4 MP, FULL HD WDR IR bullet CAMERA - 40

MTRS, colour indoor verifical dome camera, 3.6 MM

FIXED LENS, 1/3 ", 4 Mega Pixel PS CMOS Image Sensor,

WDR (120 dB), Day/ Night (ICR), IR Range of 40 Mtrs,

IP67 and all ancillary equipments and all accessories.

Nos. 4 14000 56000

CP PLUS MAKE - UNC TD40L4-D OR EQUIVALENT IN

OTHER MAKES LIKE SONY/ HONEYWELL.

Network Video Recorder

2 Supply, Installation, Testing and Commisioning of 8

CHANNEL NETWORK VIDEO RECORDER, H.264/MJPEG

dual codec decoding,Max 256 Mbps incoming

bandwidth, HDMI/ VGA simulation video output,

support 8 SATA HDD's upto 32 TB, 1 ESATA up to 16 TB,

supports multi brand network cameras. Each NVR shall

have a storage capacity so as to record a backup for 15

days at 4 CIF @ 25FPS.NVR should have system

expandibility feature of at least 20% of current

requirement, redundant fan and power supplies,

outputs TCPIP network feature & server software

monitor outputs. The NVR should be networkable via IP

protocol & should be able to connect to a web based

system for remote viewing via web system. Vendor

should submit the storage / HDD Calculation.

Nos. 0 45000 0

CP PLUS MAKE - UNR 7364R8-R OR EQUIVALENT IN

OTHER MAKES LIKE SONY/ HONEYWELL.

3 Supplying, drawing, connecting & testing of 4 pair CAT-6

(E) wire for Data Outlet in PVC conduit Mtr. 120 65 7800

TOTAL CARRIED OVER TO SUMMARY V 63800


ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA

CCTV SYSTEM

Sr. No Item Description Unit Qty Rate Amount

Date post:	19-Mar-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

TENDER DOCUMENTengineeringprojects.com/Tender/UploadFiles/3662_VOL_-_III.pdftrenches or drains (not...

Documents