Easily Selectable

Easily Serviceable

Interchangeability as easy as 1-2-3

3 Select youractuator

• Electric• Pneumatic• Thermoelectric• Thermostatic• Wireless• Spring Return• FLP Non Spring Return

Install a Spartan valve bodyassembly and easily change the

cartridge or actuator while thevalve body remains “in-line”.

Servicing is so much quicker andeasier... it’s the ultimate green

solution for piping installations.

This guide will help you select theright assembly for your needs.

As easy as 1-2-3 !

2 Select yourcartridge type

• Choice of CV• Hot and Chilled Water • 50% Glycol• Low Pressure Steam • Pressure Balanced

1 Select yourvalve body

• Female Thread • Male Thread• Solder • Single Union• Double Union

SELECTIONGUIDE

Terminal Unit Zone ValveV200/V300 Series

1⁄2” 3⁄4” 1”

A broad selection of inlet and outlet configurations and choice of sizes.

1013-1-1-01

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com

1⁄2” or 3⁄4”, 3 Way Diverting Valve Body. Conical Unions on all 3 ports

1⁄2” or 3⁄4”, 3 Way Mixing Valve Body. Conical Unions on all 3 ports

V300 Series 3 way Control Valve Bodies

General Specifications for all Valve Bodies

Terminal Unit Zone Valves SELECTIONGUIDE

Terminal Unit SelGd15 September 2017

Stem UP flow AB to A (default position),

Stem DOWN flow AB to B

Select to include: V320-12N for ½” threaded unions

V320-12S for ½” solder unions (for 5⁄8” copper pipe)

V320-34N for ¾” threaded unions

V320-34S for ¾” solder unions (for 7⁄8” copper pipe)

Select CV from cartridge type ED

Stem UP flow B to AB (default position),

Stem DOWN flow A to AB

Select to include: V321-12N for ½” threaded unions

V321-12S for ½” solder unions (for 5⁄8” copper pipe)

V321-34N for ¾” threaded unions

V321-34S for ¾” solder unions (for 7⁄8” copper pipe)

Select CV from cartridge type EX

V320 A B C D Weight 2.24 2.24 1.09 1.09 8.5oz (56,90) (56,90) (27,69) (27,69) (240g)

A B C D Weight 2.24 2.24 1.09 1.09 8.5oz (56,90) (56,90) (27,69) (27,69) (240g)

Body Material Low zinc bronze, alloy C84400

Pressure Rating ANSI 250 (400 PSI to 150˚F (66˚C), 250 PSI to 250˚ F (120˚C))

Max. Test Pressure 1200 PSI (81 bar)

Max. Differential P 50 PSI (3.5 bar) can be exceeded but with possible water noise

Valve Stem "Mirror – maker" burnished stainless steel stems

Rangeability See Internal Cartridge Specification table, on page 4

Stem Travel 5/32" (4mm)

Stem Position UP = valve open, DOWN = valve closed

AFlow Diagram

B

Stem UP flow AB to A (default position),

Stem DOWN flow AB to B

Select to include: V325-12S for ½” solder (for 5⁄8” (16mm) OD copper pipe)

V325-34S for ¾” solder (for 7⁄8” (22mm) OD copper pipe)

Select CV from cartridge type ED

1⁄2” or 3⁄4”, 3 Way Diverting Valve Body. Direct Solder1/2” Valve A B C D WeightV325-12 2.24 2.21 1.09 1.12 8.1oz (56,90) (56,13) (27,69) (28.45) (230g)3/4” Valve A B C DV325-34 2.24 3.32 1.09 2.23 8.5oz (56,90) (84,30) (25,00) (56,64) (240g)

AB

1 Select the valve body to best suit to your piping applications and choose from many connection types

Spartan Peripheral Devices 2 way V200 series and 3 way V300

series globe control valve bodies are available in a wide range of

styles and connection types. These valve bodies are common to

the complete line of Spartan Terminal Unit actuators (wireless,

electric, electronic, pneumatic and thermostatic) and are easily

interchangeable with a thumb nut.

The commercial application globe

valve bodies utilize low zinc anti

dezincification bronze.

All valve bodies are globe type rated ANSI 250 (PN 25).

ON VALVE BODIES

page

2

AFlow Diagram

B

AB

ABFlow Diagram

B

A

AFlow Diagram

B

AB

A

B

C

D

A

B

C

D

A

B

A

B

C

D

AB A

B

AB

3⁄4” or 1”, 3 Way Diverting Valve Body. Conical Unions on all 3 portsStem UP flow AB to A (default position),

Stem DOWN flow AB to B

Select to include: V345-34N for ¾” threaded unions

V345-34S for ¾” solder unions (for 7⁄8” copper pipe)

V345-10N for 1” threaded unions

V345-10S for 1” solder unions (for 11⁄8” copper pipe)

Replacement cartridge V345PKG-5.5

V345 A B C D Weight 3.25 3.00 1.50 1.50 2.35lbs 83 76 38 38 (1.07kgs)

A

B

C

D

3 WAY MIXING

3 WAY DIVERTING

V320

V345

V325

V321

A

Straight Female NPT Ports In and Out, 1⁄2”, 3⁄4” or 1”

Straight Direct Solder Connections, 1⁄2”or 3⁄4”

Stem UP open (default position)

Select to include: V241-12N for ½” threaded union

V241-34N for ¾” threaded union

V241-10N for 1” threaded union

Select CV from cartridge type EP, EB, EV or BC

Stem UP open (default position)

Select to include: V245-12S ½” Valve Body (for 5⁄8” copper pipe)

V245-34S ¾” Valve Body (for 7⁄8” copper pipe)

Select CV from cartridge type EP, EB, EV or BC

Angle Female NPT In & Male NPT Union Out, 1⁄2”, 3⁄4” or 1”

Stem UP open (default position)

Select to include: V261-12N for ½” Valve Size

V261-34N for ¾” Valve Size

V261-10N for 1” Valve Size

Select CV from cartridge type EP, EB, EV or BC

Straight Female NPT Port In & NPT Male Union Out, 1⁄2”, 3⁄4” or 1”

A B C Weight1/2” Valve 2.29 1.60 1.09 8.5ozV243-12 (58,17) (40,64) (27,69) (240g)3/4” Valve 2.70 2.20 1.09 12.7ozV243-34 (68,58) (55,88) (27,69) (360g)1” Valve 3.88 2.84 1.80 33.2ozV243-10 (98,50) (71,10) (45,70) (940g)

A B C D Weight1/2” Valve 2.25 1.13 1.13 1.25 7.8ozV261-12 (58,00) (28,00) (29,00) (32,00) (221g)3/4” Valve 2.68 1.13 0.75 1.138 8.1ozV261-34 (67,00) (30,00) (19,00) (36,00) (230g)1” Valve 3.15 1.50 2.37 1.65 32.5V261-10 (80,00) (38,00) (60,00) (42,00) (921g)

A B C Weight1/2” Valve 3.34 1.76 1.09 10.6ozV241-12 (84,84) (44,70) (27,69) (240g)3/4” Valve 3.90 2.20 1.09 12.7ozV241-34 (99,06) (55,88) (27,69) (360g)1” Valve 5.44 2.50 1.24 35.3ozV241-10 (138,00) (63,50) (31,50) (1000g)

A B C Weight1/2” Valve (16mm) 2.24 1.60 1.09 7.8ozV245-12 (56,90) (40,64) (27,69) (220g)3/4” Valve (22mm) 2.29 1.60 1.09 8.1ozV245-34 (58,17) (40,64) (27,69) (230g)

B C

A

Stem UP open (default position)

Select to include: V24020-12N for ½” threaded unions

V24020-12S for ½” solder unions (for 5⁄8” copper pipe)

V24025-34N for ¾” threaded unions

V24025-34S for ¾” solder unions (for 7⁄8” copper pipe)

V24032-10N for 1” threaded unions

V24032-10S for 1” solder unions (for 11⁄8” copper pipe)

Select CV from cartridge type EP, EB, EV or BC

Straight Flat Face Male NPT Union Connections on Both Ports, 1⁄2”, 3⁄4” or 1”

CB

Stem UP open (default position)

Select to include: V243-12N ½” Valve Body

V243-34N ¾” Valve Body

V243-10N 1” Valve Body

Select CV from cartridge type EP, EB, EV or BC

B C

A

A

BC

AD

C

B

All dimensions in inches (mm). Weight includes the internal cartridge.

Terminal Unit Zone Valves SELECTIONGUIDE

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com

V200 Series 2 way Globe Control Valve Bodies

Terminal Unit SelGd15 September 2017

page

3

Part No. Used with A B C Weight union nut1/2” Valve 3⁄4” BSPP 21⁄4” 19⁄16” 11⁄16” 8.5ozV24020FLT (57,2) (39,7) (27,0) (240g)3/4” Valve 1” BSPP 21⁄2” 21⁄8” 17⁄16” 12.7ozV24025FLT (63,5) (54,0) (36,5) (360g)1” Valve 11⁄4” BSPP 31⁄2” 23⁄8” 11⁄2” 33.2ozV24032FLT (88,9) (60,3) (38,1) (940g)

2 W

AY V240FLT

V241

V243

V245

V261

V246-12F V243-12I 1⁄2”, Flared Female SAE 45˚ unionSelection :

V243-12I for ½” union

Selection :

V246-12F for ½” union

A B WeightFlared Male V246-12F

3.125 1.32 7.8oz (79,00) (33,53) (220g)

A B WeightFlared Female V243-12I

3.125 1.32 12.7oz (79,00) (33,53) (360g)

A

B

A

B

Select CV from cartridge type EP, EB, EV or BC - see page 4. Stem UP open (default position)

1⁄2”, Flared Male SAE 45˚ union

2 Select the valve cartridge type and CV value to best suit your application such ashot and chilled water, low pressure steam or high close-off pressures.

All Spartan valve body assemblies are service/maintenance free with

interchangeable internals (in the form of a replaceable cartridge) for

specific applications with variations of equal percentage parabolic or linear

characterized globe plungers. CV (KV) values can be changed without

having to remove the valve from the line simply by changing the cartridge.

The internals are equipped with 1½ million cycles (3 million repositions),

packings with burnished mirror finish stainless steel stems and micro

machined accurate parabolic characterized plugs.

Compatible with Ethylene/Propylene Glycol.

Terminal Unit Zone Valves SELECTIONGUIDE

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com Terminal Unit SelGd15 September 2017

EPTYPE CARTRIDGE (for 2 way valve body)Used for hot and chilled water.Select from available CV’s 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, Can be installed in all 2 way ½” valve bodies

Select from available CV’s 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.5 Can be installed in all 2 way 3⁄4” valve bodies

EBTYPE CARTRIDGE (for 2 way valve body)

Balanced cartridge used for high close-off pressureapplications (up to 100 psi) for hot and chilled water.

For 2 way ½” valve bodies select from CV’s 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5 For 2 way 3/4” valve bodies select from CV’s 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.5

For 2 way 1” valve bodies select from CV’s 6.0, 6.4, 8.0, 9.0

BCTYPE CARTRIDGE (for 2 way valve body)Cage type cartridge used for low CV values.Used for hot and chilled water.Select from available CV’s 0.15, 0.25, 0.50 Can be installed in all 2 way ½”valve bodies

EDTYPE CARTRIDGE (for 3 way valve body)

Used for 3 way diverting V320, V323, V325 valvebodies for hot and chilled water. Select from available CV’s 1.0, 2.0, 3.0Can be installed in 3 way ½” and ¾” valve bodies

EVTYPE CARTRIDGE (for 2 way valve body)Used for low pressure up to 15PSI steam applicationsrecognizable by nickel plated cap.Select from available CV’s 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, Can beinstalled in all 2 way ½” valve bodiesSelect from available CV’s 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.5 Can beinstalled in all 2 way 3⁄4” valve bodiesSelect from available CV’s 6.4, 9.0 Can be installed in 2 way 1” valve bodies

Internal Cartridge Types - Field replaceable & interchangeable

Replaceable Cartridge Type EP Type EV Type BC Type EB Type ED Type EX TypeValve seat Integral bronze Integral bronze Bronze - replaceable Integral bronze Integral bronze Integral bronzeValve disc/plunger EPDM / brass Hi-temperature EPDM Brass cage EPDM / brass EPDM / brass EPDM / brassValve spring Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless SteelValve stem Burnished 303 Stainless Steel (same as EP Type) (same as EP Type) (same as EP Type) (same as EP Type) (same as EP Type)Packing Double EPDM Hi-temperature Double EPDM Double EPDM Double EPDM Double EPDM Double EPDMStroke 4mm 4mm 4mm 4mm 4mm 4mmTight close off 100 % 100 % 0.1% of Cv 100% 100% 100%Steam rated N / A 15 psi. (250ºF / 120ºC) N / A N / A N / A N / AWater rated (250ºF / 120ºC) N / A (250ºF / 120ºC) (250ºF / 120ºC) (250ºF / 120ºC) (250ºF / 120ºC)Glycol rated To 50% N / A To 50% To 50% To 50% To 50%Cv Equal % - 4mm lift 0.5,1.0,1.5,2.0,2.5,3.0 0.5,1.0,1.5,2.0,2.5,3.0 0.15,0.25,0.50 0.5,1.0,1.5,2.0,2.5,3.0,6.0,8.0 N/A N/ARangeability 100:1 100:1 100:1 100:1 - -Cv Linear - 4mm lift 2.2,3.5,4.5 2.2,3.5,4.5,6.4,9.0 N/A 2.2,3.5,4.5,6.4,9.0 1.0,2.0,3.0 1.0, 2.0,3.0 Bottom port CV 2.0

Internal Cartridge Specifications - each CV/KV is stamped on the face of the cartridge

page

4

u

u

The EB cartridge is recommended for use on certain spring return actuators. See note on page 5.

ON CARTRIDGES

ON CARTRIDGES

ON CARTRIDGES

EX TYPE CARTRIDGE (for 3 way valve body)

Used for 3 way mixing V321 valve bodies for hot and chilled water. Select from available CV’s 1.0, 2.0, 3.0Can be installed in 3 way ½” and ¾” valve bodies

ON CARTRIDGES

ON CARTRIDGES

ON CARTRIDGES

For 1⁄2” & 3⁄4” valvebodies

For 1” valve bodies

3 WAY2 WAY

3 Select the valve actuator to best suit your control signal, voltage application,spring return or FLP requirements

ELECTRIC - FAIL LAST POSITION - SYNCUBE ACTUATORSMODEL SIGNAL VOLT FEATURESME4140 Floating 24Vac End of travel switch-off, complete shutdown *ME4240 PWM 24Vac Pulse Width Modulation 0.25-5.0 secs. Feedback 1-5 Vdc *ME4340 Modulating 24Vac Selectable 0-10Vdc, 2-10Vdc, 4-20mA. Feedback 1-5 Vdc *ME4344 Modulating 24Vac Selectable 0-5Vdc, 5-10Vdc. Feedback 1-5 Vdc *

ELECTRIC - SPRING RETURN (FAIL SAFE) - POWERCUBE ACTUATORSME4430 ON-OFF 24Vac N.O. (Normally open) * ME4430S ON-OFF 24Vac N.O. (Normally open) with SPDT auxillary switch ME4431 ON-OFF 110Vac N.O. (Normally open) ME4431S ON-OFF 110Vac N.O. (Normally open) with SPDT auxillary switch ME4530 ON-OFF 24Vac N.C. (Normally closed) * ME4530S ON-OFF 24Vac N.C. (Normally closed) with SPDT auxillary switch ME4531 ON-OFF 110Vac N.C. (Normally closed) ME4531S ON-OFF 110Vac N.C. (Normally closed) with SPDT auxillary switch ME4640 Floating 24Vac N.O. (Normally open) *ME4740 PWM 24Vac N.O. (Normally open), Pulse Width Modulation 0.25-5.0 secs. Feedback 1-5 Vdc *ME4840 Modulating 24Vac N.O. (Normally open), Selectable 0-10Vdc, 2-10Vdc, 4-20mA. Feedback 1-5 Vdc *ME4844 Modulating 24Vac N.O. (Normally open), Selectable 0-5Vdc, 5-10Vdc. Feedback 1-5 Vdc *ME4940 Modulating 24Vac N.C. (Normally closed), Selectable 0-10Vdc, 2-10Vdc, 4-20mA. Feedback 1-5 Vdc * ME4944 Modulating 24Vac N.C. (Normally closed), Selectable 0-5Vdc, 5-10Vdc. Feedback 1-5 Vdc *

WIRELESS ACTUATORS - many other Wireless Actuators available at www.spartan-pd.comME8200 Modulating 24Vac FLP, operates on RF 433MHz ME8300 Modulating 24Vac FLP, operates on EnOcean TCM320(c) Dolphin module, 902 MHz America, 868 MHz Europe

THERMO-ELECTRIC ACTUATORS - SPRING RETURN (FAIL SAFE)ME1607 ON/OFF or PWM 24Vac N.O. (Normally open)

ME1707 ON/OFF or PWM 24Vac N.C. (Normally closed)

ME1707S ON/OFF or PWM 24Vac N.C. (Normally closed) with SPDT aux. switch

PNEUMATIC ACTUATORSMP5100 On-Off Modulating 3-6# N.O. Normally OpenMP5300 On-Off Modulating 7-11# N.O. Normally OpenMP5400 On-Off Modulating 5-11# N.O. Normally Open

THERMOSTATIC ACTUATORSOT1100 Valve mounted self-acting thermostatic actuator 40-80˚F (6-26˚C) OT2100/2115 Remote bulb self-acting thermostatic actuator with 6.5/16.5ft capillary 40-80˚F (6-26˚C)OT5100 Remote bulb wall-mounted self-acting thermostatic actuator with 6.5ft capillary 40-80˚F (6-26˚C)

Terminal Unit Actuators

Terminal Unit Nomenclature

Terminal Unit Zone Valves SELECTIONGUIDE

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com Terminal Unit SelGd15 September 2017

u

u

u

u

The EB cartridge is recommendedwhen using these actuators

* See individual actuator data sheets for additionalcable options

Standard clear coverOptional white cover

page

5

V E 243 - 12 N - EP 1.0 - 4340Actuator Type: ME4340

Cv Value: Cv1.0Cartridge Type: EP

Union Type - N = NPT, B = BSP, S = Solder Valve Size: 1/2”

Valve Body Type - select from connection typeValve Assembly Type - Select E for Electric, P for Pneumatic, or T for Thermostatic

STEP 1Choose a valve body{ STEP 2

Choose an internal cartridge{ STEP 3Choose an actuator{

M30 X 1.5 MOUNTING

Terminal Unit Zone Valves SELECTIONGUIDE

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com Terminal Unit SelGd15 September 2017

Terminal Unit Accessories

AV199-03 (1⁄2”, 3⁄4”), AV199-14 (1”) Pack of 10“O” rings for internal cartridges for valve bodies

OM1100P Manual adjuster for all valve bodiesBox of 10.

AVK100 Union Selection Kit. Consisting ofdifferent size and length unions

Terminal Unit Accessories

AVP20 (1⁄2”,3⁄4”), AVP116 (1”). Cap plug to replaceany valve cartridge when pipe flushing.

Flat Unions with washers

1⁄2”3⁄4” and 1”

NPT thread 1⁄2” - AV6112FLT (for valve body V24020FLT)3⁄4” - AV6534FLT (for valve body V24025FLT)1” - AV6810FLT (for valve body V24032FLT)

1⁄2” and 3⁄4” 1”

Sweat1⁄2” - AV6312SFLT (for valve body V24020FLT)3⁄4” - AV6534SFLT (for valve body V24025FLT)1” - AV6810SFLT (for valve body V24032FLT)

½” Tapered Unions (includes nut and nipple) - used with V241-12, V261-12, V320-20, V321 Valve Bodies.Union nut fits on ¾” BSPP threads

1.150”1.600”

1.650” 1.900”

2.150” 2.400”

2.650”1.090”

1.600”

page

6

1” Tapered Unions (includes nut and nipple) - used with V241-10, V261-10, V345-10 Valve BodiesUnion nut fits on 11/4” BSPP threads

1.410” 1.400”

AV6112 - ½” NPT Union, 1" nominal length nipple

AV6112D - ½” NPT Union, 11/2" nominal length nipple

AV6112F - ½” NPT Union,2” nominal length nipple

AV6112H - ½” NPT Union2½” nominal length nipple

AV6334 - 3⁄4” solder union step upfor 7⁄8” (22mm) OD copper pipe

(for ½” valves)

AV199-13 - Pack of 10 “O” rings for ½” unions (3⁄4” BSPP thread)

AV6312 - ½” solder union for 5⁄8” (16mm) OD copper pipe (for ½” valves)

AV6112G - ½” NPT Union,21/4" nominal length nipple

AV6112E - ½” NPT Union, 13/4" nominal length nipple

AV6810 1” NPT union,11/4” nominal length nipple

AV6810S 1” Solder union

AV6134 - ½” Union with 1½” nominallength. Step up 3⁄4” NPT nipple

3⁄4” Tapered Unions (includes nut and nipple) - used with V241-34, V261-34, V345-34 Valve Bodies Union nut fits on 1” BSPP threads

1.422” 2.150”

2.650” 1.466”

AV6534 ¾” NPT Union,11/4" nominal length nipple

AV6534H ¾” NPT Union,2½” nominal length nipple

AV199-08 Pack of 10 “O” rings for ¾” union (1” BSPP thread)

AV6534S ¾” Solder Union

AV6534F ¾” NPT Union,2” nominal length nipple

Installation Tools

AV08 Spud Tool for union nipple installation1/2”, 3/4” and 1” valve bodies

Terminal Unit Zone Valves SELECTIONGUIDE

Spartan Peripheral Devices telephone: (450) 424-6067 • fax: (450) 424-6071 • email: info@spartan-pd.com • website: www.spartan-pd.com Terminal Unit SelGd15 September 2017

2 way and 3 way Terminal Unit Piping Diagrams

COIL

A B A

B

COIL

A B A

B

COIL

A B A

B

COIL

COIL

3 WAY - V320, V323, V325, V345 DIVERTING VALVE BODIES1⁄2”, 3⁄4” & 1”The diverting valve body is installed on the supply side of the coil.

The water diverts in the valve and mixes in the “T” the flow enters the

common port AB

The side port A must be connected to the supply of the coil

The bottom port B must be connected to the bypass

around the coil.

STEM UP: FLOW AB-A

STEM DOWN: FLOW AB-B

3 WAY - V321 MIXING VALVE BODY - 1⁄2” and 3⁄4”The mixing valve body is installed on the return side of the coil.

The water diverts in the “T” and mixes in the valve.

Piping example No1: The flow enters port A from the coil and

port B from the bypass and exits from the common port AB

STEM UP: FLOW B-AB

STEM DOWN: FLOW A-AB

Piping example No 2: The flow enters port B from the coil and

port A from the bypass and exits from the common port AB

STEM UP: FLOW B-AB

STEM DOWN: FLOW A-AB

SOLDER INSTRUCTIONSIf direct solder bodies are used, remove the

stem packing cartridge before installation as

the heat will damage the packing.

If solder unions are used, solder the unions

without the sealing O-ring.

2 WAY - V240FLT, V241, V243, V245, V246, V261 VALVE BODIES - 1⁄2”, 3⁄4” & 1” sizes

Valve installed on the supply side of the coil.

V240, V241, V243, V245, V246, V261, V246ITERMINAL UNIT BODIES ARE NORMALLY OPEN

STEM UP: VALVE IS OPEN

STEM DOWN: VALVE IS CLOSEWhen used in conjunction with direct acting actuatorsthey become normally open valve assemblies. When used in conjunction with reverse acting actuatorsthey become normally closed valve assemblies.

Valve installed on the return side of the coil.

The valve body must be installed in thedirection indicated on the valve body cavity

Example 2

Example 1

StemUp

AB A

B

StemDown

AB A

B

StemUp

AB A

B

StemDown

Stem UpValve Open

Multi CV  cartridges replaceable inline

Stem DownValve Closed

AB A

B

page

7

IMPORTANT INSTALLATION NOTESThe complete valve assembly can be installed vertically or horizontally; it cannot be installed upside down. The Actuator mounting thumbnut is to be tightened by hand only, using tools may result in over-tightening. Thumbnut

CANADA187 Joseph Carrier, Vaudreuil,

Quebec. J7V 5V5

UNITED STATES100 Walnut Street, Champlain,

N.Y. 12919

telephone TOLL-FREE in North America: (888) 554-4465telephone: (450) 424-6067fax: (450) 424-6071

email: info@spartan-pd.comwebsite: www.spartan-pd.com

CONTROLSWITHOUTCOMPROMISE

Printed in Canada 2018

Distributed by