tesa Solutions for the Flexible Packaging Industry
Optimizing the Entire Printing Process
Recovery Rate Printing Set-up
Comparison of Print Results
Increase of Peel Adhesion
tesa® Softprint –
Optimum Thickness Tolerances:
The properties of the PE (polyethylene)
foam used have been optimized with
thickness tolerances in mind; the foam
has been neither thermally nor mechan-
ically manipulated during production.
The consistent tape thickness supports
consistent ink distribution.
Set-up time is also reduced, which is
especially important for repeat jobs.
Always the right adhesive strength,
which ensures:
Simple repositioning of tape and plate
before printing
High bond strength during printing,
eliminating edge-lifting
Low increase in peel adhesion allows
for simple, residue-free demounting of
both plate and tape after printing
Set-up time
Reliable Technique, Proven Performance: tesa® Softprint 20-mil
This tesa solution was developed and
tested in close cooperation with well-
known press manufacturers under a
variety of typical production conditions.
Their unanimous assessment:
The details make the difference!
The PE (polyethylene) foam has an opti-
mized recovery capability, supporting
consistent print results at higher speeds.
Higher foam elasticity transmits even
the finest plate details.
The secret of tesa® Softprint foam:
Small, completely closed,
spherical foam-cells
Evenly distributed cell structure
Stable foam structure at speeds
up to 600 meters/minute
tesa adhesive tape Market standard
0 24 48 72 96 120 144 188
45
40
35
30
25
20
15
10
5 Time in hours
Adhesion in %
Market standard
tesaadhesive tape
Marketstandard
Foam poresprior to printing
Foam pores after1,000,000 metersof printed web
Standard plate mounting tape
tesa® 52223 helps to minimize
the unwanted stripes, which is
achieved by absorbing and
minimizing the vibrations during
printing.
tesa® 52223 Softprint x-Soft
With conventional plate mount-
ing tapes, press vibrations cause
unwanted stripes, which means
an imperfect print image. Block
and even screen printed areas
appear faint.
Succeed with tesa –Take Advantage of the Best Performance
With a comprehensive range of tapes
for flexo printers, tesa offers solutions
to fulfill every requirement:
Plate mounting tapes for highly
demanding print motifs
Graduated adhesive strengths
for the latest sleeve qualities
tesa® EasySplice® FilmLine
for high speed flying splice
processes
Printing is a business where both
excellent print results and high
process efficiency go hand in hand.
For many years, tesa® Softprint
plate mounting tapes have delivered
on both these counts, helping
printers to optimize print results
and improve processes. With our
industry experience and under-
standing of the total process, tesa
provides adhesive solutions for
every step of the flexible packaging
print-run.
In combination with the unrivaled
service provided by our industry
experts across the world, tesa
provides packaging printers with
ideas to optimize their processes,
along with the means to make
it happen.
The starting point for achievinga new dimension of efficiency –tesa® 51905 EasySplice® FilmLine –now for flexo printers, too!
Since 2000, tesa has led the application of
modern straight-line splicing in the paper
producing and converting industries. This
innovative concept now comes to the film-
processing industry with tesa® EasySplice®
FilmLine. Because of recognizable improve-
ments in efficiency, tesa® EasySplice®
FilmLine is increasingly regarded as the
standard method for splicing in the package
printing industry.
Splicing
Easy and fast splice
preparation, high splice security,
constant print results, and less waste
tesa® 51905 EasySplice® FilmLine
Failure Flagging
Varied color offering allows
for distinct imperfection
marking
tesa® 4104
Core Starting
Sufficient adhesion properties to
attach the web to the core
tesa® 4959
End-Tabbing
Safe bonding on all substrates; in
different colors or transparent version
tesa® 4104
Roller Wrapping
Keeps the printed substrate evenly dis-
tributed during printing; ensures greater
reliability and continuity in the print run;
the adhesive allows easy removal, even
after a prolonged period.
tesa® 4563 (smooth)
tesa® 4863 (embossed)
Plate Mounting
The characteristics of foam quality, along
with other variables, have a crucial effect
on print result. All tesa plate mounting
tapes are characterized by:
Constant tape thickness
Optimized recovery rate
High and even foam elasticity
Edge Sealing
tesa supplies plate edge-sealing products
with a broad range of benefits. The adhe-
sive sticks to photopolymer plates and
is subsequently easy to remove without
leaving any residue.
tesa® 53016
tesa® 53017
The formula for meeting increased
demand for the best flexo printing is:
the finer the dots, the harder the plate,
and the softer the tape.
Digitally produced plates are harder
and allow the finest dots, so a softer
tape is needed.
tesa has adapted its
assortment of foam-
based plate mounting
tapes to meet the demands of
today’s different applications.
tesa products prove their impressive quality day in day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to thebest of our knowledge on the basis of our practical experience. Nevertheless, tesa tape, inc. can make no warranties, expressed or implied, including, but not limited to any implied warrantyor merchantability or fitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa product is fit for a particular purpose and suitable for the user's methodof application. If you are in any doubt, our technical support staff will be glad to advise you.
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
©tesa
tape,inc.8-2008
UNITED STATES & CANADA
tesa tape, inc.
5825 Carnegie Boulevard
Charlotte, NC 28209
Phone: 704 554 0707
Toll Free: 800 426 2181
Fax: 800 852 8831
Email: [email protected]
Website: www.tesatape.com
MEXICO
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
tesa Flexible Packaging Tapes
tesa® 52020 Softprint
tesa® 52021 Softprint
tesa® 52022 Softprint
tesa® 52120 Softprint
tesa® 52121 Softprint
tesa® 52122 Softprint
tesa® 52220 Softprint
tesa® 52221 Softprint
tesa® 52222 Softprint
tesa® 52223 Softprint
tesa® 51905 EasySplice® FilmLine
tesa® 53016
tesa® 53017
tesa® 4563
tesa® 4863
tesa® 4959
tesa® 4104
PE1 foam
PE foam
PE foam
PE foam
PE foam
PE foam
PE foam
PE foam
PE foam
PE foam
Paper
S-PVC2
S-PVC
Si-coat3 fabric
Si-coat fabric
Non-woven
H-PVC4
Plate Mounting
Splicing
Edge Sealing
Roller Wrapping
Core Starting
Flagging/End-Tabbing
Backing
Blue logo
Purple logo
Red logo
Blue logo
Purple logo
Red logo
Blue logo
Purple logo
Red logo
Yellow logo
Red
Yellow
White
Gray, Smooth
Gray, Structured
Translucent
8 Colors
Colors
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Modified rubber
Modified rubber
Modified rubber
Modified rubber
Modified rubber
Modified acrylic
Rubber
Adhesive
20 mil
20 mil
20 mil
20 mil
20 mil
20 mil
20 mil
20 mil
20 mil
20 mil
4 mil
5.3 mil
6 mil
16 mil
25 mil
4.5 mil
2.5 mil
Tape ThicknessApplication Product
1PE - polyethylene 2S-PVC - soft-polyvinyl chloride 3Si-coat - silicone rubber-coated fabric 4H-PVC - hard-polyvinyl chloride
the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]
tesa® 15-mil Plate Mounting Tapes for Labelprint
15MilBrochureREV.qxd 7/16/07 2:07 PM Page 2
Steel Master™ tesa® 52015 tesa® 52017
Prin
ting
Plat
e tesa® 52117tesa® 52115Steel Master™ TP*
Printin
gPla
te
1.70 mm / 0.067 thou
1.14 mm / 0.045 thou
1.70 mm / 0.067 thou
1.14 mm / 0.045 thou
*TP - Thin Plate
tesa® Plate Mounting Tapes – for best print results
In label printing, quick and straight-
forward tape handling really matters
so that plates can be easily replaced.
Labels for modern-day packaging
require complex print motifs – fine
screen, exact barcode, fine color
gradients, and solid areas. Labels must
be produced in the highest quality on
paper or film.
A specialized assortment with two
different grades of foam hardness and
various film-based qualities provides
solutions for all plates. tesa offers a
range of new products, with differenti-
ated adhesive strengths, promoting
damage-free demounting of thin plates.
15MilBrochureREV.qxd 7/16/07 2:07 PM Page 3
The details make the difference
the PE foam has an optimized recovery
capability, guaranteeing consistent print
results at higher speeds
higher foam elasticity transmits even
the finest plate details
magnification under screen-electron-
microscopes reveals the secret of the
tesa® softprint foam:
- small, completely closed, spherical
foam cells
- very evenly distributed cell structure
Always the right adhesivestrength, thereby ensuring:
simple repositioning of tape and plate
before printing
high bond strength during printing,
ensuring no edge lifting, even when
using the tape a second time
simple and residue-free demounting
of plate and tape following printing,
made possible by a low increase in
peel adhesion
tesa® Softprint – optimum thickness tolerances
the properties of the PE (polyethylene)
foam in use have been optimized
with thickness tolerance in mind –
the foam has been neither thermally
nor mechanically manipulated during
production
the constant tape thickness supports
consistent ink distribution. Set-up time
is also reduced, especially important
for repeat jobs
Recovery Rate
Foam pores prior to printing
Foam pores after 1,000,000 mof printed strip
Increase of Peel Adhesion
adhesion levelin %
Market standard
time in hours
45
40
35
30
25
20
15
10
5
0 24 48 72 96 120 144 168
tesa adhesive tape
Market standard
Printing Set-up
tesa® adhesive tape Market standard
15MilBrochureREV.qxd 7/16/07 2:07 PM Page 4
Always the right product
For each print job, you can choose the right tape hardness and special adhesive, all of which have proven themselves on all current
plates (also on .045 mil). tesa has the product with the ideal properties for superior print quality and simple, fast handling.
tesa® Steel Master TP
tesa® 52338
tesa® 52115 tesa® 52117
tesa® 52015 tesa® 52017
tesa® 15-mil Softprints (Combination Print)
tesa® Steel Master - for steel cylinders- high initial adhesion- color coding
Soft foam Medium-hard foam Film
- for steel cylinders- high initial adhesion- graded adhesion- thin plates (.045 mm)- color coding- easy to demount
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to the best of our knowledge on thebasis of our practical experience. Nevertheless, tesa can make no warranties, expressed or implied, including, but not limited to any implied warranty of merchantability or fitness for a particular purpose. The user, there-fore, is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical support staff will be glad to advise you.
©tesa
tape,inc.7-2007
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
NORTH AMERICA
tesa tape, inc.
5825 Carnegie Boulevard
Charlotte, NC 28209
Phone: 704 554 0707
Toll Free: 800 426 2181
Fax: 800 852 8831
Email: [email protected]
Website: www.tesatape.com
15MilBrochureREV.qxd 7/16/07 2:07 PM Page 1
the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]
For stable and precise
printing, slitting, or
converting, we offer our well-known grip tapes or tension control products, commonly called “Printer’s Friends” (tesa® 4863
and tesa® 4563). With their unique siliconized backing, they are extremely resistant to both ink and solvents and provide a
non-slip effect on smooth surfaces that come into their contact. In addition, the thermoset rubber adhesive allows r esidue-free
removal from most surfaces.
Edge sealing tapes
For sealing the edges of flexographic printing plates, tesa® 53016 and tesa® 53017 provide a highly flexible backing combined
with an aggressive adhesive that will secure edges in the most demanding printing environments. tesa® edge seal tapes are solvent
resistant and provide residue-free, clean removal. tesa® 53016 is intended for general-purpose applications, while tesa® 53017
is especially well suited for the highest-quality photopolymer printing plates available.
Non-stick
roller wrap
tapes for
gripping
®
®
®
Check out the detail – and discover the proof
of tesa’s “softprint®” foam quality
Only round and uniform cells can fully rebuild themselves after compression.
The images from a scanning electron microscope (REM) confirm that
tesa softprint® provides the perfect cell structure for plate mounting
applications. Uniformity of height is present, and the cells display neither
vertical nor horizontal orientation.
These cells are rounded, well
defined, and distributed evenly,
while maintaining their height.
They are not al igned in one
direction and, therefore, are able
to completely rebuild after
compression.
Medium foam for combinations of
halftone and solid work
Softer foam for excellent
halftone results
FOAM HARDNESS AND YOUR OPTIONS FOR BETTER PRINTING QUALITY
PRINTING OF SOLID AREAS*
* Printed at DFTA, Germany; impression set at 150 µm (microns) / 6 mils
tesa® 4863
tesa® 4563
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to the best of our knowledge on the basis of our practical experience. tesa, however, can make no warranties, expressed or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical support staff will be glad to advise you. tesa maintains the right to amend the products for technical reasons without prior notice as long as the agreed specifications of the product are still fulfilled. In case of legal problems, tesa is entitled to stop deliveries of the products without delay and without compensation to the customer. In this case, tesa will contact the customer without delay to find a solution for the delivery of alternative products.
tesa tape, inc.
5825 Carnegie BoulevardCharlotte, NC 28209Phone: 704 554 0707Toll Free: 800 426 2181Fax: 800 852 8831 Email: [email protected] Website: www.tesatape.com
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
UNITED STATES & CANADA
© tesa tap
e, inc. 11-2008
tesa Product Assortment for Plate Mounting
Harder foam for combination print of halftone and solid work
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
MEXICO
tesa® 53016
tesa® 53017REM image of tesa softprint®
For stable and precise
printing, slitting, or
converting, we offer our well-known grip tapes or tension control products, commonly called “Printer’s Friends” (tesa® 4863
and tesa® 4563). With their unique siliconized backing, they are extremely resistant to both ink and solvents and provide a
non-slip effect on smooth surfaces that come into their contact. In addition, the thermoset rubber adhesive allows r esidue-free
removal from most surfaces.
Edge sealing tapes
For sealing the edges of flexographic printing plates, tesa® 53016 and tesa® 53017 provide a highly flexible backing combined
with an aggressive adhesive that will secure edges in the most demanding printing environments. tesa® edge seal tapes are solvent
resistant and provide residue-free, clean removal. tesa® 53016 is intended for general-purpose applications, while tesa® 53017
is especially well suited for the highest-quality photopolymer printing plates available.
Non-stick
roller wrap
tapes for
gripping
®
®
®
Check out the detail – and discover the proof
of tesa’s “softprint®” foam quality
Only round and uniform cells can fully rebuild themselves after compression.
The images from a scanning electron microscope (REM) confirm that
tesa softprint® provides the perfect cell structure for plate mounting
applications. Uniformity of height is present, and the cells display neither
vertical nor horizontal orientation.
These cells are rounded, well
defined, and distributed evenly,
while maintaining their height.
They are not al igned in one
direction and, therefore, are able
to completely rebuild after
compression.
Medium foam for combinations of
halftone and solid work
Softer foam for excellent
halftone results
FOAM HARDNESS AND YOUR OPTIONS FOR BETTER PRINTING QUALITY
PRINTING OF SOLID AREAS*
* Printed at DFTA, Germany; impression set at 150 µm (microns) / 6 mils
tesa® 4863
tesa® 4563
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to the best of our knowledge on the basis of our practical experience. tesa, however, can make no warranties, expressed or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical support staff will be glad to advise you. tesa maintains the right to amend the products for technical reasons without prior notice as long as the agreed specifications of the product are still fulfilled. In case of legal problems, tesa is entitled to stop deliveries of the products without delay and without compensation to the customer. In this case, tesa will contact the customer without delay to find a solution for the delivery of alternative products.
tesa tape, inc.
5825 Carnegie BoulevardCharlotte, NC 28209Phone: 704 554 0707Toll Free: 800 426 2181Fax: 800 852 8831 Email: [email protected] Website: www.tesatape.com
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
UNITED STATES & CANADA
© tesa tap
e, inc. 11-2008
tesa Product Assortment for Plate Mounting
Harder foam for combination print of halftone and solid work
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
MEXICO
tesa® 53016
tesa® 53017REM image of tesa softprint®
®
Thanks to tesa softprint®, it is finally
feasible for a wide-web printer to
carry out even the most difficult
printing jobs with the highest
quality. Whether printing on paper
or film, fine screens, solid areas, or lines – everything is possible. We at tesa
offer a wide range of softprints® and tesaprints®. The tesa® Steel Master products
are designed for mounting photopolymer plates onto steel cylinders, while
tesa® Sleeve Master products are for mounting plates onto polyurethane sleeves.
STANDARD tesapr int ®
LinerProduct Thickness (mm/mil) Color Backing
tesapr int ® for postpr int in corrugated industry
LinerProduct Thickness (mm/mil) Color Backing
LinerProduct Thickness (mm/mil) Color Backing
tesa® BigFoam - higher tack
tesa® BigFoam TP - lower tack
*without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - for plate thickness .067”-.107” - colored marking
tesa® Steel Master TP - for steel cylinders - plate easier to reposition - for plate thickness .045”-.067” - colored marking
tesa products for
corrugated board
printing
tesa products for
printing flexible
packaging
tesa products for
label printing
For high-quality label printing,
we at tesa offer a wide range
of 15 mil softprints®. Due to their
adhesive system, the tesa® Steel Master products are well suited for mounting
photopolymer plates onto steel cylinders. In addition to the tesa softprints®, there is
a wide range of tesaprints®.
For corrugated board preprint,
a variety of tesa products are
available in sizes ranging from
15 mil to 20 mil softprints®. For corrugated board postprint, there is a full range of
filmic prints. Due to its high adhesion values, tesaprint® 52332 is especially designed
for permanent mounting.
* without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - colored marking
tesa® Steel Master TP - for steel cylinders - lower tack - white
Softer foam for halftone process
tesa® 52117
For today’s flexo printer, printing quality and secure bonding of plate to cylinder are the most significant requirements –
a fact that reflects the demands on the tapes used for mounting plates. tesa offers a complete range of plate mounting tapes
that provide a product solution for virtually every flexo printing application.
* µm = microns
Harder foam for combination print
Super soft foam for fine screen
Harder foam for combination print
Medium foam for halftone and solids
Softer foam for halftone
tesa® Sleeve Master - for polyurethane sleeves
- plate easier to reposition
- for plate thickness .045”-.067”
- colored marking
tesa softpr int ® 60 mi l
tesa softpr int ® 20 mi l
white embossedpolypropylene liner
0.11 / 4 colorless,transparent
filmtesa® 52310
white embossedpolypropylene liner
0.15 / 6 yellow,transparent
filmtesa® 52315
white embossedpolypropylene liner
0.20 / 8 white filmtesa® 52320
white embossedpolypropylene liner
0.24 / 10 pink filmtesa® 52325
creped paper liner
0.38 / 15 white woventesa® 52330
white embossedpolypropylene liner
0.38 / 15 black soft filmtesa® 52338
white embossedpolypropylene liner
0.50 / 20 black soft filmtesa® 52350
yellow paper0.10 / 4 colorless,transparent
filmtesa® 52916
tesa® 52060
tesa® 52062
tesa softpr int ® 15 mi l
Harder foam for combination print
tesa® 52015
tesa® 52115
Softer foam for halftone
tesa® 52017
tesa® 52222
tesa® 52122
tesa® 52022
Medium foam for halftone and solids
tesa® 52221
tesa® 52121
tesa® 52021tesa® 52020
tesa® 52120
tesa® 52220
1
2
For high-quality results from flexo printing, consider tesa first!
tesa® 52223tesa® 52223
yellow paper0.12 / 4.8 colorless,transparent
filmtesa® 52917
tesapr int ® for compressib le s leeves
tesa® 52118tesa® 52118
Super soft foam for fine screen
tesa® 52015
tesa® 52115
tesa® 52017
tesa® 52117
tesa® 52020
tesa® 52120
tesa® 52220
tesa® 52021
tesa® 52121
tesa® 52221
tesa® 52022
tesa® 52122
tesa® 52222
®
Thanks to tesa softprint®, it is finally
feasible for a wide-web printer to
carry out even the most difficult
printing jobs with the highest
quality. Whether printing on paper
or film, fine screens, solid areas, or lines – everything is possible. We at tesa
offer a wide range of softprints® and tesaprints®. The tesa® Steel Master products
are designed for mounting photopolymer plates onto steel cylinders, while
tesa® Sleeve Master products are for mounting plates onto polyurethane sleeves.
STANDARD tesapr int ®
LinerProduct Thickness (mm/mil) Color Backing
tesapr int ® for postpr int in corrugated industry
LinerProduct Thickness (mm/mil) Color Backing
LinerProduct Thickness (mm/mil) Color Backing
tesa® BigFoam - higher tack
tesa® BigFoam TP - lower tack
*without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - for plate thickness .067”-.107” - colored marking
tesa® Steel Master TP - for steel cylinders - plate easier to reposition - for plate thickness .045”-.067” - colored marking
tesa products for
corrugated board
printing
tesa products for
printing flexible
packaging
tesa products for
label printing
For high-quality label printing,
we at tesa offer a wide range
of 15 mil softprints®. Due to their
adhesive system, the tesa® Steel Master products are well suited for mounting
photopolymer plates onto steel cylinders. In addition to the tesa softprints®, there is
a wide range of tesaprints®.
For corrugated board preprint,
a variety of tesa products are
available in sizes ranging from
15 mil to 20 mil softprints®. For corrugated board postprint, there is a full range of
filmic prints. Due to its high adhesion values, tesaprint® 52332 is especially designed
for permanent mounting.
* without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - colored marking
tesa® Steel Master TP - for steel cylinders - lower tack - white
Softer foam for halftone process
tesa® 52117
For today’s flexo printer, printing quality and secure bonding of plate to cylinder are the most significant requirements –
a fact that reflects the demands on the tapes used for mounting plates. tesa offers a complete range of plate mounting tapes
that provide a product solution for virtually every flexo printing application.
* µm = microns
Harder foam for combination print
Super soft foam for fine screen
Harder foam for combination print
Medium foam for halftone and solids
Softer foam for halftone
tesa® Sleeve Master - for polyurethane sleeves
- plate easier to reposition
- for plate thickness .045”-.067”
- colored marking
tesa softpr int ® 60 mi l
tesa softpr int ® 20 mi l
white embossedpolypropylene liner
0.11 / 4 colorless,transparent
filmtesa® 52310
white embossedpolypropylene liner
0.15 / 6 yellow,transparent
filmtesa® 52315
white embossedpolypropylene liner
0.20 / 8 white filmtesa® 52320
white embossedpolypropylene liner
0.24 / 10 pink filmtesa® 52325
creped paper liner
0.38 / 15 white woventesa® 52330
white embossedpolypropylene liner
0.38 / 15 black soft filmtesa® 52338
white embossedpolypropylene liner
0.50 / 20 black soft filmtesa® 52350
yellow paper0.10 / 4 colorless,transparent
filmtesa® 52916
tesa® 52060
tesa® 52062
tesa softpr int ® 15 mi l
Harder foam for combination print
tesa® 52015
tesa® 52115
Softer foam for halftone
tesa® 52017
tesa® 52222
tesa® 52122
tesa® 52022
Medium foam for halftone and solids
tesa® 52221
tesa® 52121
tesa® 52021tesa® 52020
tesa® 52120
tesa® 52220
1
2
For high-quality results from flexo printing, consider tesa first!
tesa® 52223tesa® 52223
yellow paper0.12 / 4.8 colorless,transparent
filmtesa® 52917
tesapr int ® for compressib le s leeves
tesa® 52118tesa® 52118
Super soft foam for fine screen
tesa® 52015
tesa® 52115
tesa® 52017
tesa® 52117
tesa® 52020
tesa® 52120
tesa® 52220
tesa® 52021
tesa® 52121
tesa® 52221
tesa® 52022
tesa® 52122
tesa® 52222
®
Thanks to tesa softprint®, it is finally
feasible for a wide-web printer to
carry out even the most difficult
printing jobs with the highest
quality. Whether printing on paper
or film, fine screens, solid areas, or lines – everything is possible. We at tesa
offer a wide range of softprints® and tesaprints®. The tesa® Steel Master products
are designed for mounting photopolymer plates onto steel cylinders, while
tesa® Sleeve Master products are for mounting plates onto polyurethane sleeves.
STANDARD tesapr int ®
LinerProduct Thickness (mm/mil) Color Backing
tesapr int ® for postpr int in corrugated industry
LinerProduct Thickness (mm/mil) Color Backing
LinerProduct Thickness (mm/mil) Color Backing
tesa® BigFoam - higher tack
tesa® BigFoam TP - lower tack
*without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - for plate thickness .067”-.107” - colored marking
tesa® Steel Master TP - for steel cylinders - plate easier to reposition - for plate thickness .045”-.067” - colored marking
tesa products for
corrugated board
printing
tesa products for
printing flexible
packaging
tesa products for
label printing
For high-quality label printing,
we at tesa offer a wide range
of 15 mil softprints®. Due to their
adhesive system, the tesa® Steel Master products are well suited for mounting
photopolymer plates onto steel cylinders. In addition to the tesa softprints®, there is
a wide range of tesaprints®.
For corrugated board preprint,
a variety of tesa products are
available in sizes ranging from
15 mil to 20 mil softprints®. For corrugated board postprint, there is a full range of
filmic prints. Due to its high adhesion values, tesaprint® 52332 is especially designed
for permanent mounting.
* without stabilizing film, black
tesa® Steel Master - for steel cylinders - higher tack - colored marking
tesa® Steel Master TP - for steel cylinders - lower tack - white
Softer foam for halftone process
tesa® 52117
For today’s flexo printer, printing quality and secure bonding of plate to cylinder are the most significant requirements –
a fact that reflects the demands on the tapes used for mounting plates. tesa offers a complete range of plate mounting tapes
that provide a product solution for virtually every flexo printing application.
* µm = microns
Harder foam for combination print
Super soft foam for fine screen
Harder foam for combination print
Medium foam for halftone and solids
Softer foam for halftone
tesa® Sleeve Master - for polyurethane sleeves
- plate easier to reposition
- for plate thickness .045”-.067”
- colored marking
tesa softpr int ® 60 mi l
tesa softpr int ® 20 mi l
white embossedpolypropylene liner
0.11 / 4 colorless,transparent
filmtesa® 52310
white embossedpolypropylene liner
0.15 / 6 yellow,transparent
filmtesa® 52315
white embossedpolypropylene liner
0.20 / 8 white filmtesa® 52320
white embossedpolypropylene liner
0.24 / 10 pink filmtesa® 52325
creped paper liner
0.38 / 15 white woventesa® 52330
white embossedpolypropylene liner
0.38 / 15 black soft filmtesa® 52338
white embossedpolypropylene liner
0.50 / 20 black soft filmtesa® 52350
yellow paper0.10 / 4 colorless,transparent
filmtesa® 52916
tesa® 52060
tesa® 52062
tesa softpr int ® 15 mi l
Harder foam for combination print
tesa® 52015
tesa® 52115
Softer foam for halftone
tesa® 52017
tesa® 52222
tesa® 52122
tesa® 52022
Medium foam for halftone and solids
tesa® 52221
tesa® 52121
tesa® 52021tesa® 52020
tesa® 52120
tesa® 52220
1
2
For high-quality results from flexo printing, consider tesa first!
tesa® 52223tesa® 52223
yellow paper0.12 / 4.8 colorless,transparent
filmtesa® 52917
tesapr int ® for compressib le s leeves
tesa® 52118tesa® 52118
Super soft foam for fine screen
tesa® 52015
tesa® 52115
tesa® 52017
tesa® 52117
tesa® 52020
tesa® 52120
tesa® 52220
tesa® 52021
tesa® 52121
tesa® 52221
tesa® 52022
tesa® 52122
tesa® 52222
For stable and precise
printing, slitting, or
converting, we offer our well-known grip tapes or tension control products, commonly called “Printer’s Friends” (tesa® 4863
and tesa® 4563). With their unique siliconized backing, they are extremely resistant to both ink and solvents and provide a
non-slip effect on smooth surfaces that come into their contact. In addition, the thermoset rubber adhesive allows r esidue-free
removal from most surfaces.
Edge sealing tapes
For sealing the edges of flexographic printing plates, tesa® 53016 and tesa® 53017 provide a highly flexible backing combined
with an aggressive adhesive that will secure edges in the most demanding printing environments. tesa® edge seal tapes are solvent
resistant and provide residue-free, clean removal. tesa® 53016 is intended for general-purpose applications, while tesa® 53017
is especially well suited for the highest-quality photopolymer printing plates available.
Non-stick
roller wrap
tapes for
gripping
®
®
®
Check out the detail – and discover the proof
of tesa’s “softprint®” foam quality
Only round and uniform cells can fully rebuild themselves after compression.
The images from a scanning electron microscope (REM) confirm that
tesa softprint® provides the perfect cell structure for plate mounting
applications. Uniformity of height is present, and the cells display neither
vertical nor horizontal orientation.
These cells are rounded, well
defined, and distributed evenly,
while maintaining their height.
They are not al igned in one
direction and, therefore, are able
to completely rebuild after
compression.
Medium foam for combinations of
halftone and solid work
Softer foam for excellent
halftone results
FOAM HARDNESS AND YOUR OPTIONS FOR BETTER PRINTING QUALITY
PRINTING OF SOLID AREAS*
* Printed at DFTA, Germany; impression set at 150 µm (microns) / 6 mils
tesa® 4863
tesa® 4563
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to the best of our knowledge on the basis of our practical experience. tesa, however, can make no warranties, expressed or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical support staff will be glad to advise you. tesa maintains the right to amend the products for technical reasons without prior notice as long as the agreed specifications of the product are still fulfilled. In case of legal problems, tesa is entitled to stop deliveries of the products without delay and without compensation to the customer. In this case, tesa will contact the customer without delay to find a solution for the delivery of alternative products.
tesa tape, inc.
5825 Carnegie BoulevardCharlotte, NC 28209Phone: 704 554 0707Toll Free: 800 426 2181Fax: 800 852 8831 Email: [email protected] Website: www.tesatape.com
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
UNITED STATES & CANADA
© tesa tap
e, inc. 11-2008
tesa Product Assortment for Plate Mounting
Harder foam for combination print of halftone and solid work
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF SOLID AREAS*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
PRINTING OF HALFTONE*
MEXICO
tesa® 53016
tesa® 53017REM image of tesa softprint®
the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]
Plate Mounting Tape: A good one mounts - the better one secures
tesa Softprint® SecureThe specially developed solution for print process productivity
tesa Softprint® Secure – the ultimate solution to
promote higher print process efficiency.
tesa Softprint® Secure stands for:
optimal print results and result consistency
the highest plate security on the market
increased process productivity and output
Specially developed with the most
demanding process parameters in
mind, tesa Softprint® Secure takes
edge security to a new level.
tnirptfoS asetdradnats tekraM ® Secure
Package printing in the 21st century has taken print results and production quality to new levels.
Now the market will be challenged to maximize the efficiency of the production process, while
keeping print results at the level that printers and clients have come to expect.
Equipped with a revolutionary adhesive system,
tesa Softprint® Secure maintains consistent,
original placement of plates and plate edges,
regardless of cylinder, sleeve, or plate
dimensions, press speed, or length of print run.
Testing has demonstrated that
many tapes fail to secure plates
over the duration of the print
job, which can place limits on
the print process.
©tesa tape, inc. 4-2009
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are providedto the best of our knowledge on the basis of our practical experience. Nevertheless tesa SE can make no warranties, express or implied, including, but not limited to any impliedwarranty of merchantability or fitness for a particular purpose. Therefore, the user is responsible for determining whether the tesa® product is fit for a particular purpose andsuitable for the user’s method of application. If you are in any doubt, our technical support staff will be glad to advise you.
tesa tape inc.
5825 Carnegie Boulevard
Charlotte, N.C. 28209
Phone: 704 554 0707
Toll Free: 800 426 2181
Fax: 800 852 8831
Email: [email protected]
Website: www.tesatape.com
UNITED STATES & CANADA
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
MEXICO
Overview of the benefits
Specially designed
“Secure” adhesive
Explanation Benefit
Keeps plates mounted securely
tesa Softprint® foamSuperior print results at highest
speeds, even on longer jobsPolyethylene (PE) foam with closed, round cells
tesa Service Maximize machine potentialExperts on site to give advice
on upgrading processes
tesa® Softprint Secure 20mil
Please ask your tesa® representative for more details.
Hard foam Medium foam Soft foam
228251282502825tesa Softprint® Secure
Color Coding per foam hardness
20 milThickness
No press stops for remounting
Easy demounting
No primer needed – no residues
No sealing tape necessary
No damaged plates
the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]
Faster print runs, finer screens,less bouncing, better results
tesa® 52223 Softprint x-Soft
The leading plate mounting solutionwith extra-soft foam – tesa® 52223Softprint x-Soft.
Finer screen printing with better results at higher speeds. What wasonce a goal of modern flexographicprinters now becomes a reality withtesa® 52223 Softprint x-Soft.
Digital plates now deliver the finestscreens ever, with their harder textureallowing the finest dots; but this comes at a cost. A harder plate needsextra cushion to ensure consistent,spectacular print results.
tesa® 52223 Softprint x-Soft is a specially designed, extra-soft foam plate mounting tape, giving plates theideal cushion to transfer the finestscreens and lower dot gain.
The extra-soft foam of tesa® 52223Softprint x-Soft also works effectivelyin another challenging area — overcom-ing press bounce. The foam absorbsunwanted vibrations, allowing fasterprinting speeds without compromisingprint results — an ideal solution to one of the most pressing problems for modern flexographic printers.
tesa® 52223 Softprint x-Soft isredefining boundaries for flexographicprinting. Improved performance and efficiency provide benefits that printersand their customers really notice.
Contact your tesa representativetoday, 800-426-2181.
Increased dot gain
Bouncing stripes Optimum results
tesa® 52223 Softprint x-Soft – solving problems at higher speeds
tesa® 52223 Softprint x-Soft – the finest screens in the finest detail
Optimum resultsMissing screens
Other plate mounting tapes
Other plate mounting tapes
tesa® 52223 Softprint x-Soft
tesa® 52223 Softprint x-Soft
tesa® 52223 Softprint x-Soft – benefits overview
tesa® products prove their impressive quality day in day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to the best of ourknowledge on the basis of our practical experience. Nevertheless, tesa tape, inc. can make no warranties, expressed or implied, including, but not limited to any implied warranty or merchantability orfitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you arein any doubt, our technical support staff will be glad to advise you.
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
Extra-soft foam
Superiorfoam recovery
Tight thicknesstolerances
Ideal solutions with harderdigital plates for finest screens
Helps compensate for press vibrations
Faster printing speeds
Allows over pressure
Consistent print results —even on longer, faster print runs
Extra-soft foam for perfect cushion,reducing dot-gain
Solids are also possible if machines are adjusted
Faster, more accurate job set-up and no missing screens
Tight control of tolerances promotes absolute consistency in print results
Even, stable, closed-cell foam structure ensures excellent results, impression
after impression
Extra-soft foam compensates for press vibrations, even at increased speeds,
thus eliminating bouncing stripes
Benefit Explanation
Specially developed plate-side adhesive
Superior application, mounting, and repositioning
Helps avoid edge lifting and plate movement during printing; ensures
residue-free demounting and removal
Specially optimizedopen-side adhesive
Secure bonding to sleeves and cylinders Secure printing with easy, residue-free removal properties
1PE - polyethylene 2PP - polypropylene
©tesa
tape,inc.11-2007
Technical Details
tesa® 52223Softprint x-Soft 20 mil
— PE1 foam(extra soft)
— Closed cell— Yellow ID logo
— Acrylic— Enhanced removal
ThicknessProduct Backing Adhesive Liner
— PP2-filmic— White— Embossed
UNITED STATES & CANADA
tesa tape, inc.
5825 Carnegie Boulevard
Charlotte, NC 28209
Phone: 704 554 0707
Toll Free: 800 426 2181
Fax: 800 852 8831
Email: [email protected]
Website: www.tesatape.com
MEXICO
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977 the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]
tesa Solutions for Label Printing
Optimizing the Entire Label Printing Process
Benefits You Really Notice
At a Glance: Reliable Technique, Proven Performance, Better Results
Optimum thickness tolerances:
Stable print results
The constant tape thickness supports
consistent ink distribution. Set-up time
is also reduced, which is especially
important for repeat jobs.
Optimal register
The consistent tape thickness also
supports perfection of register.
Constant circumference of printing cylinder
Fast set-up of die-cutting unit – less waste
Die-cutting precision
Recovery rate
Magnification under scanning electron
microscope reveals the secret of
tesa® Softprint foam:
Small, completely closed, spherical
foam-cells
Very evenly distributed cell structure
over the entire dimension of the tape
Always the right adhesive strength,
which ensures:
Simple repositioning of tape and plate
before printing
High bond strength during printing,
eliminating edge-lifting, even when tape
is used a second time
Low increase in peel adhesion allows for
simple, residue-free demounting of plate
and tape
The simple, reliable handling of
tesa products makes a notice-
able difference in the work of a
label printer. These products
save time, render some steps
redundant, and make a signifi-
cant contribution to top-quality
print results.
tesaadhesive tape
Marketstandard
tesaadhesive tape
Marketstandard
Set-up time
tesa® Softprint
0 24 48 72 96 120 144 188
45
40
35
30
25
20
15
10
5 Time in hours
Adhesion in %
Market standard
Improve Your Process – Succeed with tesa
Permanent Splicing
For preparation of butt
splices without a liner; the
sufficient adhesion and tensile
strength are suitable for all materials with
alternatives for higher temperatures.
tesa® 4104
tesa® 4137 (heat resistant)
Label designs continue to become more and more demanding,
with both product appeal and large amounts of information to
consider. The drive for optimization of print results means that
process efficiency has even greater significance in modern
label printing than ever before.
tesa solutions for label printers include all parts of the
process. tesa® Softprint plate mounting tapes optimize
results and achieve process excellence, while innovations
like tesa® UV Strips ensure reliable process output.
These adhesive solutions, coupled with the superior
service provided by tesa industry experts worldwide,
make tesa the adhesive partner to the label printing
industry in the 21st Century.
Failure Flagging
For marking defective
points during the
printing process.
tesa® 4104
UV Measuring
tesa® UV Strips offer a fast and easy
way to measure UV (ultraviolet)
light doses. The results of the
system are unique in constancy
and reliability. It can be used for
all UV curing inks and lacquers.
tesa® 54140
Roller Wrapping
Keeps the printed substrate
evenly distributed during
printing; ensures greater
reliability and continuity
in the print run; the adhesive
allows easy removal, even after
a prolonged period.
tesa® 4563 (smooth)
tesa® 4863 (embossed)
End-Tabbing
For safe bonding on all
substrates; available in different
colors or transparent versions.
tesa® 4104
Core Starting
Excellent adhesion properties
to ensure the web is securely
attached to the core.
tesa® 4959
Edge Sealing
tesa supplies plate edge-sealing products with a
broad range of benefits. The adhesive sticks to
photopolymer plates and, subsequently, is easy to
remove without leaving any residue.
tesa® 53016
tesa® 53017
tesa Plate Mounting Tapes –Meeting Increased Demands for the Best Print Results
The characteristics of foam quality, along
with other variables, have a crucial effect
on print results. All tesa plate mounting
tapes are characterized by:
Constant tape thickness
Optimized recovery rate
High foam elasticity
The formula for meeting increased demand
for the best flexo printing is: the finer the
dots, the harder the plate, and the softer
the tape.
tesa® Softprint Toolbox 15mil
tesa® Softprint SteelMaster TP
tesa® Softprint SteelMaster
tesa® 52015 tesa® 52017
The tesa® Softprint Toolbox is a specialized assortment with two different
grades of foam hardnesses, and two different adhesive systems, for
thicker or thinner plates.
The broad range combines optimal solutions for achieving superior print
results, while providing easy selection of the appropriate tape.
Enhancing print results has never been easier!
TP represents “thin plate” for high cylinder-side adhesion and a tailored
bond for easy demounting, even of thin plates (0.045“).Medium-hard foam Soft foam
tesa® 52115 tesa® 52117
tesa® Softprint x-Soft provides an optimum solution for finest screen printing
with 80 lines/cm or more.
The extra soft foam also compensates for press vibrations, thereby
improving overall printing processes by helping machines run faster while
improving print results.
tesa® Softprint x-Soft is equipped with optimized adhesive properties to
promote optimal tape handling, mounting, and demounting.
Missing screens Increased dot gain Optimum results
tesa Specialty Solutions for Sleeves and Steel Cylinders
Extra soft foam
tesa® Softprintx-Soft
tesa® 52118
Other plate mounting tapestesa® 52118Softprint x-Soft
Medium-hard foam Soft foam
012 4786 99235 9852 65519 0119 84
Extra Soft Foam
Medium-hard
foam for combi-
nation print
Extra soft
foam for fine
screen print
Soft foam for
halftone print
tesa Label Printing Tapes
tesa® 52015 Softprint
tesa® 52017 Softprint
tesa® 52115 Softprint
tesa® 52117 Softprint
tesa® 52118 Softprint x-Soft
tesa® 4104
tesa® 4137
tesa® 53016
tesa® 53017
tesa® 4563
tesa® 4863
tesa® 4959
tesa® 4104
tesa® 54140
Plate Mounting
Splicing
Edge Sealing
Roller Wrapping
Core Starting
Flagging/
End-Tabbing
UV Measuring
Backing Color(s) Adhesive
15 mil
15 mil
15 mil
15 mil
15 mil
2.5 mil
2 mil
5.3 mil
6 mil
16 mil
25 mil
4.5 mil
2.5 mil
1.5 mil
Tape thicknessApplication Product
PE1 foam
PE foam
PE foam
PE foam
PE foam
H-PVC2
PET3
S-PVC4
S-PVC
Si-coat fabric5
Si-coat fabric
Non-woven
H-PVC
PET
Blue logo
Red logo
Blue logo
Red logo
Yellow logo
8 Colors
Silver
Yellow
White
Gray, Smooth
Gray, Structured
Translucent
8 Colors
Transparent
Acrylic
Acrylic
Acrylic
Acrylic
Acrylic
Rubber
Modified acrylic
Modified rubber
Modified rubber
Modified rubber
Modified rubber
Modified acrylic
Rubber
Acrylic1PE - polyethylene 2H-PVC - hard polyvinyl chloride 3PET - polyester 4S-PVC - soft polyvinyl chloride 5Si-coat - silicone rubber-coated fabric
ISO 9001:2000 Certified • ISO/TS 16949:2002 Certified • ISO 14001:2004 Certified
©tesa
tape,inc.8-2008
UNITED STATES & CANADA
tesa tape, inc.
5825 Carnegie Boulevard
Charlotte, NC 28209
Phone: 704 554 0707
Toll Free: 800 426 2181
Fax: 800 852 8831
Email: [email protected]
Website: www.tesatape.com
MEXICO
Technical Tape México S.A. de C.V.
Av. Santa Fe No. 170
German Centre P 6-3-3Col.
Lomas de Santa Fe
Mexico D.F. C.P. 01210
Phone: +52 (55) 5292 6978
Fax: +52 (55) 5292 6977
tesa products prove their impressive quality day in day out in demanding conditions and are regularly subjected to strict controls. All information and recommendations are provided to thebest of our knowledge on the basis of our practical experience. Nevertheless, tesa tape, inc. can make no warranties, expressed or implied, including, but not limited to any implied warrantyor merchantability or fitness for a particular purpose. The user, therefore, is responsible for determining whether the tesa product is fit for a particular purpose and suitable for the user'smethod of application. If you are in any doubt, our technical support staff will be glad to advise you.
the Difference!Experi
ence
Toll-free: 866.282.7697 • Fax: 800.223.6869www.AndVre.com • E-mail: [email protected]